Mtc. of road from i). Netaji Chowmuhani to IS Office. (Ch 0.00 to 0.400 Km. ii) IS Office to Loknath Asram (Ch 0.00 km to 0.200 Km). under PWD (R and B) Sabroom Division during the year 2025-26.

Construction of Embankment with Material Obtained from Borrow Pits Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per MoRD Technical Specification Clause 301.5.

Demolishing cement concrete manually / by mechanical means including disposal of material with all lifts and upto 50 m lead etc. complete as per direction of the Engineer- in-charge:- Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Compacting original ground supporting subgrade Loosening of the ground upto a level of 300 mm below the subgrade level, watered, graded and compacted in layers to meet requirement of Tables 300.1 and 300.2 for subgrade construction as per MoRD Technical Specification Clause 303.5.2.

Granular Sub-base with Well Graded Material (Table 400.1) using Jhama Brick Aggregate (A) By Mix in Place Method Construction of granular sub-base by providing well graded material (Jhama Brick Aggregate, Grading-I, as per Table 400.1, spreading in uniform layers with tractor with attachments on prepared surface, mixing by mix in place method with rotavator at OMC, applying and brooming sand to fill up the interstices of coarse aggregate, watering and compacting with smooth wheel roller to achieve the desired density, complete as per MoRD Technical Specification Clause 401 (i) For Grading - I Material (jhama brick aggreate)

1) WBM Grading 3 : Providing, laying, spreading and compacting 63 mm to 0.075 mm jhama brick aggregates to water bound macadam specification including spreading in uniform thickness, hand picking rolling with three wheel roller 80-100 KN in stage to proper grade and camber, applying and brooming and binding materials to fill up the interstices of coarse aggregate , watering and compacting to the required density Grading 2 as per MoRD Technical Specification Clause 405. (A) By manual means

Tack coat using hot straight run bitumen of grade VG-30 on W.B.M. Providing and applying tack coat using hot straight run bitumen of grade VG-30, including heating the bitumen, spraying the bitumen, cleaning and preparing the existing road surface as per specifications: On W.B.M. @ 0.75 kg/ sqm.

Tack coat using hot straight run bitumen of grade VG-30 on bituminous surface. Providing and applying tack coat using hot straight run bitumen of grade VG-30, including heating the bitumen, spraying the bitumen, cleaning and preparing the existing road surface as per specifications: On bituminous surface @ 0.50 Kg/ Sqm.

20mm thick open –graded premix carpet using Bituminous (penetration grade / Modified bitumen) binder. Providing & laying rolling of open –graded carpet of 200mm thickness composed of 13.2mm to 5.6mm aggt.Either using penetration grade bitumen of emulsion to required line, grade & level to serve as wearing course on a previously prepared base in/c. mixing in a suitable plants, laying & rolling with a three wheel 80-100km static roller capacity, finished to required level & grades to be followed by seal coat of either type A or type B C or type D as per MoRD technical specification clauses 508. 1) By Manual means Means.I) Bitumen VG-30

Seal Coat Providing & laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade & cross fall using type A or B type C or D as per MoRD technical specification clauses 510.1) By Manual Means. Case-iv : Type D ( Premix with fine sand ) I) Bitumen VG-30

Maintenance of bituminous surface road I. Repair to pot holes by removal of failed material, trimming the sides to vertical and levelling the bottom, cleaning the same with compressed air or any appropriate method, filled with 75 mm B.M, after applying bitumen emulsion prime coat at the bottom and bitumen emulsion tack coat on sides and on bottom as per MoRD technical specification Clauses 1900, 502, 503 and 504.

Road marking strips (retro-reflective) of specified shade/ colour using Hot Applied Thermoplastic material with Reflectorising Glass Beads on Bituminous Surface Providing and applying 2.5 mm thick thick road marking strips (retro-reflective) of specified shade/ colour using hot thermoplastic material including reflectorising glass beads @ 250 gms per sqm area by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater including cost of cleaning the road surface of all dirt, seals, oil, grease and foreign material etc, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes as per MoRT&H Technical Specification Clause 803.