PROVISION AND ADDITION/ALTERATION OF TOILETS AT VARIOUS LOCATIONS AT AF STN AND SPECIAL REPAIRS TO DRAIN AT CSD DEPOT MISSAMARI UNDER GE MISAMARI

Amount

Demolition of Brick Work or Stone/ Bolder masonary built in Cement Mortar including all Quoins, Arches, Pillars, etc. of any description, complete all as specified and as directed. Note:Demolished material to be used for filling under floors to bring upto required level.

Demolition of Cement Concrete (un-reinforced) of any description in Ground Floors, Pavings, etc. not exc. 150mm thickness (above or below Ground Level), complete all as specified and as directed. (Note:Demolished material to be used for filling under floors to bring upto required level, if neccesary)

Demolition of Cement Concrete (reinforced) of any description and in any position not otherwise specifically provided for,complete all as specified and as directed.

Dismantling Bricks (laid Flat or on edge) or bricks tiles in floors, channel, kerbs, aprons etc (each layer), Bricks laid, bedded and pointed in any Mortar, complete all as specified and as directed.

Dismantling of 600 mm bore cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required, complete all as specified and as directed.

Surface dressing n exc15 cm deep in soft and loose soil, complete all as specified and directed.

Excavation in trenches not exc. 1.5 Metre Wide and not exc. 1.50 Metre in Depth for foundation etc. or for Shafts, Wells, Cess Pits, Manholes, Pier Holes for laying of UG Cable/Pole/Stays etc, and getting out as in Soft/Loose Soil, complete all as specified and as directed.

Returning, Filling in, including Spreading, Levelling, Watering and Well Ramming in Layers not exc. 25 Cm in Soft/Loose Soil, complete all as specified and as directed.

Removing excavated Materials (Soils) n.exc.50.00 Metre and depositing where directed at a level not exc. 1.50 Metre above the Starting Point in Soil, complete all as specified and as directed.

Removing excavated Materials (Soils) exc. 50.00 Metre but n. exc. 500 meter and depositing where directed at a level not exc. 1.50 Metre above the Starting Point in Soil, complete all as specified and as directed.

Removing excavated Materials (Soils) exc. 1.5 KiloMetre but n. exc. 5 Kilometer and depositing where directed at a level not exc. 1.50 Metre above the Starting Point in Soil, complete all as specified and as directed.

M&L for Cement Concrete 1:4:8, Type D2, (40mm graded aggregate) in Foundations, Filling and Mass Concrete, etc. complete all as specified and as directed.

M&L for Cement Concrete 1:3:6, Type C2, (40mm graded aggregate) in surface channels and drain, complete all as specified and as directed.

M & L for 75mm thick cement concrete 1:3:6 type C2, using 40 mm graded aggregate as in plinth protection and finishing surface even and smooth without using extra cement, complete all as specified and as directed.

M&L for Cement Concrete Bed 1:3:6 type C2 (40mm graded aggregate) of 600mm bore (dia) Drain Pipes including Packing under and completely surrounding pipe with concrete they Laying and Testing of Pipe, complete all as specified and as directed.

S & F for NP3 600mm dia reinforced cement concrete pipe class NP3 laid and jointed, complete all as specified and directed.

M&L for Non skid ceramic coloured jointless tiles 7 to 8mm thick (Square/ Rectangular) area of each tiles exceeding 0.11 Sqm but n.exc. 0.18 Sqm in floors etc. over and including 15 mm thick screed bed in CM 1:4 set and jointed in neat cement slurry and pointed in white or colored cement to match the surface of tiles complete all as specified and as directed.

M&L for glazed ceramic coloured tiles, glossy finished of size 300x200x7mm thick as in vertical surfaces such as skirting/dados and riser of stems., over and including including 10 mm thick rendering/backing coat in CM 1:3 and set and jointed in neat cement slurry and pointed in white or colored cement to match the surface of tiles,complete all as specified and as directed.

M&L for Rendering 5mm thick in Cement Mortar 1:3 on fair faces of ceiling , plastered surfaces finished Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L for Rendering 10mm thick in Cement Mortar 1:4 on Brick Walls or on Concrete Surfaces, plastered surfaces finished Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L for Rendering 15mm thick in Cement Mortar 1:4 on Brick Walls or on Concrete Surfaces, plastered surfaces finished Even and Smooth without using Extra Cement, complete all as specified and as directed.

Supply only Integral Water Proofing Compound, conforming to IS-2465-1975 and/or as approved, complete all as specified and as directed.

M&L for Cement Concrete 1:2:4 (20mm graded aggregate) as in Kerbs, Coping, mud stops etc. including weathering, slightly rounded or Chamfered angles and throating including use and waste of Formwork as required/ordered at Site(s), complete all as specified and as directed

Cleaning to Drain by taking out Brick Bat, Pebbles, Slits, Muds, Clay, Sludge etc from the bottom of Drains and culvert bed and removing to a distance not exc 50.00 meter and depostied, complete all as specified and directed.

S&F Factory made Solid PVC Door Frame of size 50x47 mm made out of 5.0 mm thick wood grain printed PVC sheet reinforced with Mild Steel Square Tube and edges will be painted to match with printed sheet and fixing in opening as per Specification and Drawing of MES Schedule Part-II, complete all as specified and as directed.

S&F Factory made Solid Panel PVC Door Shutter 30mm thick (Style) consisting of Frame made out of Mild Steel Square Tube for Top and Bottom Rails, mild steel Frame shall be covered with heat moulded plain colour PVC 'C' Channel having PVC Sheet Strip 20 mm wide stuck inside with Solvent Cement for Styles and plain colour PVC Sheet for Top Rail, Lock Rail & Bottom Rail on either side and as gap insert for Top Rail, Bottom Rail Panelling of plain colour PVC Sheet to be fitted in mild steel Frame welded/sealed to the Styles and Rails with suitable Sheet Beading and jointed together with Solvent Cement and fixing in the Frame at Site as per Specification and Drawing of MES Schedule Part-II, complete all as specified and as directed.

S&F stainless Steel Butt Hinge of size 100mm, medium weight, cold rolled and fixed, complete all as specified and as directed

S&F Aluminium Handle 150mm long Cast type, complete all as specified and as directed.

S&F Aluminium anodised Barrel Tower Bolt 150 mm long, Extruded Section and fixed, complete all as specified and as directed.

Supply & laying Steel Water Tubing 15mm bore (dia), galvanised, ‘medium grade’ with all Fittings, fixed on walls, ceiling or laid in floors or any other situation, complete as all specified and as directed.

All as per Item No.30 here in before but for 20 mm, complete all as specified and directed.

S&F Pillar Tap 15mm bore (dia), Cast Copper Alloy, Chromium Plated with Capstan Heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed Shanks and Fly-nuts, screwed for Iron Pipe and fixed, complete all as specified and as directed.

S&F Stop Cock 15mm bore , Chromium Plated with long shank, fancy type, screwed down high pressure with Crutch or Butter-fly Handle, screwed both Ends for Iron Pipe or for Unions and fixed, complete all as specified and as directed.

S&F Bib Tap 15mm bore (dia), Cast Copper Alloy, Chromium Plated with Crutch or Butter-fly Handle, screwed down, screwed for Iron Pipe or for Brass Ferrule and fixed, complete all as specified and as directed.

S&F CP fancy type twin Angle valve 15mm dia (angle cock) cast copper alloy, complete all as specified and as directed.

Supply and fix CP Health Faucet with 1.50 Metre Tube & Hook (as approved) and fixed, complete all as specified and as directed.

S&F Brass Chromium plated Tubular Towel Rail, 20mm dia, D-type, 60 Cm long between Flanges with Bracket (one Pair) and fixed, complete all as specified and as directed.

S&F vitreous china wash hand basin, white size 550 x 400 mm incl bracket & waste coupling complete all as specified and as directed.

S&F vitreous china wash down water closet pan (pedestal pattern) white incl seat cover of plastic, CP jet and pipe etc complete incl necssary PVC pipe fittings, complete all as specified and as directed.

S&F PVC low level flushing cistern white including flush pipe suitable for IWC/EWC, 10 Lit capacity complete all as specified and as directed.

S&F PVC Connection Pipe 15mm in size with PTMT Nuts of length 450mm and fixed, complete all as specified and as directed.

S & F PVC waste pipe of 32 mm bore of adequate length complete all as specified and as directed.

S&F PTMT grating Doom 125mm dia (minimum weight 40 Grams) complete all as specified and as directed.

S&F PVC (SWR) 75mm bore (dia) Soil, Waste and Ventilating Pipe, Single Socketed, in any length with Rubber Ring Joints, laid in Trenches or in Floors complete all as specified and as directed.

S&F PVC (SWR) 110 mm bore (dia) Soil, Waste and Ventilating Pipe, double Socketed, in any length with Rubber Ring Joints, laid in Trenches or in Floors complete all as specified and as directed.

M&L for brick work with sub-class ‘B’ Bricks, straight or curved on plan exc 6m mean radius, built in Cement Mortar 1:4, complete all as specified and as directed.

M&L for Brick Work with Sub-Class ‘B’ Bricks (with Old Size Bricks), Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and as directed.

M&L for brick work with sub-class ‘B’ Bricks Straight or Curved on Plan to any radius in half brick thick built in Cement Mortar 1:4, complete all as specified and as directed.

M&L for brick work with sub-class ‘B’ Bricks Straight or Curved on Plan to any radius in half brick thick built in Cement Mortar 1:3, complete all as specified and as directed.

M&L for brick work (except brick) with sub-class ‘B’ Bricks Straight or Curved on Plan to any radius in half brick thick built in Cement Mortar 1:3, complete all as specified and as directed.

M&L for brick work with sub-class ‘B’ Bricks in one brick thick honycomb walling built in Cement Mortar 1:4, complete all as specified and as directed.

M&L for Formwork to Sides of Concrete Foundations, Footings, bases of Columns, Raft and Raft Beams, Sides and Soffits (if any) of foundation and plinth beams and similar work; Square, rectangular or polygonal, vertical or to batter, flat, rough finished surfaces of concrete, complete all as specified and as directed.

M&L for Formwork to Sides and Soffits of Floor or Roof Beams, Lintels, Cantilevers, Shelves including Supports, Overhangs, etc. also splays between Floors and Beams, etc., rough finished surfaces of Concrete, complete all as specified and as directed.

M&L for Formwork to Soffits of suspended Slabs such as Roof Slabs, Floor Slabs, Landings and similar work; not exc. 200mm thick (horizontal or sloping), rough finished surfaces of Concrete, complete all as specified and as directed.

M&L for Formwork to sides of Pillars, Posts, Struts, Piers, Columns and stanchions, flat, rough finished surfaces of concrete, complete all as specified and as directed.

M&L for TMT Bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia, complete all as specified and as directed.

M&L for TMT Bars 5mm dia and over upto and including 10mm dia in Stirrups, Spacers and Binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia, complete all as specified and as directed.

M&L for Reinforced Cement Concrete 1:2:4 type B1(20mm graded stone aggregate) in columns, pillars, piers, post and strut, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be measured and paid separately under relevant Items.

M&L for Reinforced Cement Concrete (Nominal Mix) 1:2:4 type B1 (20mm graded aggregate) in Foundations including Rafts, Footings, Foundation Beams; Plinth Beams; bases for Columns, etc.; Basement Slabs, Under-reamed Piles and Mass Concrete, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be measured and paid separately under relevant Items.

M&L for Reinforced Cement Concrete (Nominal Mix) 1:2:4,type A1 (20mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.50 Metre span, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be measured and paid separately under relevant Items.

M&L for Reinforced Cement Concrete (Nominal Mix) A1 1:2:4 (20mm graded stone aggregate) as in slab supported on wall,beam and column in floor,roof,landing,balconies,canopies,deck slab and in shelves and the like, complete all as specified and as directed. NOTE : Reinforcement & Formwork will be measured and paid separately under relevant Items.

M& L for Providing precast RCC type B1 1:2:4 (20 mm graded aggreagae) as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in cement mortar 1:4, complete all as specified and as directed.

M&L for Hardcore of broken stone or boulders of gauge exc. 63mm but not exc.100mm, deposited, spread and levelled in layers not exc. 15 Cm thick, watered and rammed to a True Surface, complete all as specified and as directed.

M&L for sand filling under floors spread, levelled, watered and well rammed in layers n.esc 25 cm thick, complete all as specified and as directed.

M&L for 100mm thick Cement Concrete 1:4:8, type D2 (40mm graded aggregate), as in Sub-base finishing Concrete Surfaces Even and rough, complete all as specified and as directed.

M&L for 50mm thick Cement Concrete 1:3:6, type C2 (40mm graded aggregate), as in Sub-base finishing Concrete Surfaces Even and rough, complete all as specified and as directed.

S&F Vitreous China Urinal, Half stall type, white including Push cock, Spreader white complete all as specified.

S&F PVC (SWR) floor trap, plain with grating, Diameter of outlet 110mm, including jointing with solvent cement complete all as specified and as directed.

S&F PVC (SWR) floor trap, plain with grating, Diameter of outlet 75mm, including jointing with solvent cement complete all as specified and as directed.

M&L for preparing new Plastered Surfaces of Walls and applying Two Coats of Cement Base Paint over a coat of primer, complete all as specified and as directed.

M&L for preparing newly plastered surfaces of wall and applying Three Coats of White Wash, complete all as specified and as directed

M&L for preparing newly plastered surfaces of Ceiling and applying Three Coats of White Wash, complete all as specified and as directed

M&L for preparing new or previously untreated Steel and Iron Surfaces of any description, over. 10 Cm Width or Girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L for Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and as directed.

S & F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded incl hinges peg stay, glass pane, wire mesh etc complete all as specified and directed.

M&L for Rotational Moulded Polyethene Water Storage Tank 1000 Litre Capacity (Cylindrical, Vertical with Closed Top), 3 layered, hoisted and fixed in Position all as specified in MES Schedule , complete all as specified and as directed.

S&F Ball Valve 20mm dia (minimum Weight 210 Gram), high pressure of PTMT with epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe and fixed, complete all as specified and as directed.

M&L for Sheet Glass, Ordinary, 4.0mm thick, Glazing in Wooden/Metal Frames and glazed with Beads or Oil Putty, area not exc. 0.50 SQM in Each Pane, complete all as specified and as directed.

M&L for 10 User LDPE septic tank, complete all as specified and as directed.

M&L for Cement Concrete Bed 1:3:6 (40mm graded aggregate) of 150mm bore (dia) Drain Pipes including Packing under and Haunching to Sides of the pipes after Laying and Testing of Pipe, complete all as specified and as directed.

S&F for double wall corrugated DWCPE pipes 200mm dia conforming to IS 16098(part-2): 3013 laid in trenches and jointed complete all as specified and as directed.

Supply and fill brick bats on soak pit complete all as specified and as directed.

M&L for Cutting into existing manholes 150mm dia of internal pipe for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and as directed.

Taking down carefully Copper/Aluminium Point Wiring (Light, Fan, Socket or Power) of any description on batten/conduit and making good disturbed surfaces of Ceiling, Walls, etc. in Cement Mortar 1:3 and providing Surface Treatment so as to match the existing Finishes, complete all as specified and as directed.

Taking down the existing unservicable main switch/ cut out/ DBs of any type/ capacity/ description as existing at site including making good the disturbed surfaces to match with the existing finishes all as specified.

Taking down the existing unservicable UG cable of any type/ description as existing at site including making good the disturbed surfaces to match with the existing finishes all as specified.

M&L for Point Wiring with 1.5 Sqmm Copper Conductor single core PVC insulated Flame Retardant Low Smoke (FRLSH) Unsheathed 1100 Volt grade multi-stranded Cable drawn through and including Rigid PVC Conduit, medium grade, ISI marked of suitable size and its Accessories as required at Site, fixing on surface of Wall, Roof, mounted on Sunk Mild Steel Pressed Terminal Box 1.22mm thick of suitable size duly painted with red oxide metal primer with 3.0mm thick Plastic Laminated Sheet Top Cover for mounting Switches, Sockets, etc. including PVC insulated and unsheathed Single Core multi-stranded Copper Conductor Cable of size 1.5 Sqmm (FRLS) Green in Colour as Earth Continuity Conductor connected to Common Earth and Earth dolly for One Light Point controlled by One 1-Way Switch 5 Amp, complete all as specified and as directed.

All as per item No. 88 here in before for One Ceiling Fan/Exhaust Fan Point controlled by One 1-Way Switch 5 Amp and Regulator, complete all as specified and as directed.

All as per Item No. 88 here in before but or One 3 Pin 5 Amps Switch Socket Outlet Point controlled by One Switch on Independent Board, complete all as specified and as directed

S&F Switch Piano, Flush type, Single Pole, 1-Way, 5 Amps, 230 Volt, conforming to IS and connecting up, complete all as specified and as directed.

S&F Switch Socket Combination 2-in-1, Flush type, multi-purpose, 3 Pin, 6 Amp, 240 Volt, conforming to IS and connecting up, complete all as specified and as directed.

S&F Ceiling Rose, Surface Bakelite of size 65x50mm, 3 Terminals, AC, 50 Hz, 240 Volts, conforming to IS and connecting up, complete all as specified and as directed.

S&F Lamp Holder Surface Bakelite with Back Plate insulated body suitable for Batten/Angle Fittings and fixed with PVC Block, conforming to IS and connecting up, complete all as specified and as directed.

S & F LED ADORE 10 W B22 CDL 5 STAR LAMP with B 22 base capacity 1200 lumen complete all as specified and as directed.Make : Havells, Cat No: LHLDEUEBML8Z010 or equivalent in CG/Polycab.

S & F wall mounted LED 10 watts , batten type T5 mirror light fitting (Warm light), 230 volts with extruded aluminium heat sink provided for efficient heat dissipation and intregrated electronic driver connector block etc complete with all accessories internally pre wired and necessary mounting arrangements ,provision of new 3 core multistranded copper conductor of size 23/0.193 from celing rose to fitting, complete all as specified and as directed.

S & F wall mounted LED 18 watts , batten type T8 light fitting, 230 volts with extruded aluminium heat sink provided for efficient heat dissipation and intregrated electronic driver connector block etc complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including ultra bright LED polycarbonate(T8) tube (single side connection) 4' x 18 watts with G13 lamp holdercomplete all as specified and as directed. Make- Havells, Model -REGALBATTENT5UPTO1X18WDSBSWH For Batten Fitting and Model-PHOTONULTRAE2.01213T8SSTL18WLED865SPC For T8 Tubelight or equivalent in CG/Polycab.

S & F sheet metal enclosure MCB DB SPN 4 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system complete including removal of old unsv sheet metal enclosure all as specified. Make :-L&T model No. DBSPN004DD or equivalent in Legrand/Havells.

S&F MCB Double Pole, 32 Amps, 240/415 Volt for fixing on MCB DB’s, 10 kA,c curve 50 Hz, conforming to IS/IEC 60898 and connecting up, complete all as specified and as directed.(Make- L&T, Cat No: BB20320B, BB20320C or erquivalent in Schinder/Legrand.)

S&F MCB SP,6-32 Amps, 240 Volt for fixing on MCB DB’s, 10 kA,c curve 50 Hz, conforming to IS/IEC 60898 and connecting up, complete all as specified and as directed.(Make- L&T, Cat No: BB10060C , BB10100C, BB10160C or equivalent in Schinder/Legrand.)

S & F Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 security light fitting luminaire with high power LEDs as light source and PC cover having top opening seperate driver compartment with IP 66 protection and impact resistance of IK07 with electronic driver of capacity 15 watts with pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting and GI pipe bracket made out of GI pipe medium grade 32 mm dia 1.5 mtr long bend to required shape complete all as specified and as directed.Make-Havells,Model No - ENDURAPEARLSL15WLED757SASYTOPCMP or equivalent in CG/POLYCAB.

S&F Sub-Class ‘B’ Brick, well burnt, laid breadthwise along the length of Cable laid in trenches over Sand Cushion laid for UG Cable Protection, complete all as specified and as directed.

M&L for Sand Cushioning (dry) in trenches/ducts for protection of UG Cables (below, above and around the UG Cable laid in Trenches) of 23 Cm Spread thickness (8 Cm in depth before laying the Cable and 15 Cm in depth after lay-ing the Cable) and consolidated (punned) upto 180mm thickness, complete all as specified and as directed. NOTE: For the purpose of Payment, Punned thickness of Sand Cushioning only shall be measured and paid for.

Supply & laying LT UG XLPE sheathed PVC insulated, screened PVC bedded, Galvanised Steel Strip of Wire armoured Electric Power Cable heavy duty with stranded Aluminium Conductor 1100 Volt grade, cross-sectional area 10 Sqmm 2.0 Core, laid in trenches/surface of Wall/in GI Pipe along with Pole for connec-tion to OH Lines including Brass Cable Glands Mild Steel Flat Iron Clamps, etc. and Testing, complete all as specified and as directed. NOTE : Earthwork, Sand Cushioning, Bricks, GI Pipe, etc. will be measured and paid under appropriate Items.

S&F Galvanised Iron Pipe 40mm bore (dia), Light grade as in protection of UG Cable laid in Trenches/fixing with Poles with Mild Steel Flat Iron Clamps, complete all as specified and as directed. NOTE: Cost of Mild Steel Clamp, Nuts, Bolts and painting is deemed to be included in the QUOTED UNIT RATE.

S&F Galvanised Iron Pipe 50mm bore (dia), Light grade as in protection of UG Cable laid in Trenches/fixing with Poles with Mild Steel Flat Iron Clamps, complete all as specified and as directed. NOTE: Cost of Mild Steel Clamp, Nuts, Bolts and painting is deemed to be included in the QUOTED UNIT RATE.

S&F heavy duty exhaust fan 300 mm sweep MS body, 3 wing 1400 rpm, single phase 240 volts copper wounds complete with all accessories as louvers shutters etc incl making connection through 3 core PVC coper wire run through flexible pipe. Single phase type.

Boring holes horizontally under Road without damaging the surface of Road of any type (minimum 1.0 METRE below the Road Surface with the help of GI Tubing not exc. 40 mm bore (dia) for passing of UG Cable, complete all as specified and as directed.

M&L for Earthing complete with Galvanised Steel Earth Plate Electrode 600x600x6mm, buried directly in ground vertically to a depth not less than 2.25 Metre below ground level with Top Edge of Earth Plate at depth not less than 1.50 Metre below normal ground level, connected to Galvanised Earth Lead Wire 4.0mm dia by means of Bolts, Nuts, Check, Nuts and Washers of Galvanised Iron or Steel and Earth Wire protected with and including GI Pipe 15mm bore (dia) ‘light grade’ upto 1.0 Metre above the Floor Level of Building where Main Switch/ DB situated, Earth Plate surrounded by a packed thickness of Char Coal or Coke Dust mixed with Common Salt in alternate layers of not exc. 150 mm thick, PCC Pit in Cement Concrete 1:3:6 (20mm graded aggre gate) and Pre-cast RCC Cover Slab of size 350x350x50 mm in Cement Concrete 1:2:4 (20mm graded aggregate), reinforced with 8.0mm dia TMT Bars @ 100mm Centre to Centre in both ways, GI Wire Mesh, Funnel with GI Watering Pipe 20mm bore (dia) ‘medium grade’ including necessary Excavation in Soft/Loose Soil, Returning, Filling in and Removal of surplus Spoil upto a distance of 50.00 Metre and all as shown in Electrical Plate No. 3 of MES Schedule Part-I and Testing on Completion including removal old existing unserviceable Earthing, complete all as specified and as directed.

S&F 3 layered(Outer green coloured UV stabalized,middle black coloured UV stabalized and inner most layer white coloured with antimicrobial property) PP-R (Polypropyelene random copolymer) pipe 32mm outer dia,ISI marked,SDR 7.4 and SDR11 UV stabalised and antimicrobial fusion welded having thermal stabality for hot and cold water supply all PP-R plain and brass threaded polypropyelene random fittings and laid in treanches, complete all as specified and directed.

S&F 40mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed (as approved) complete all as specified and as directed.

S&F 25mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed (as approved) complete all as specified and as directed.

Cutting of existing CI/DI pipe laid 50 mm dia for inserting Tees for new connection of 50x40 mm diacomplete all as specified and as directed.

M&L for GI connection pieces for inserting 25 mm PPR pipe into 50 mm distribution mains all as specified and directed.

M&L for fixing GI plug into 40 mm distribution mains all as specified and directed.

M/S Krishna Construction Co.

Markson

M/S K.K.TRADERS

MS Gautam Construction and CO

R D ENTERPRISE