Construction of Porta Cabin...

Amount

[10.10.1]Providing and laying Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 1. 40 mm thick with 20 mm nominal size stone aggregate [Through Rate]

[12.102.1]Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 1. 125 mm [Through Rate]

[12.98.2]Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 2. 250x16 mm [Through Rate]

[12.99.4]Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 4. 150x10 mm [Through Rate]

[13.29.2]Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 2. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works [Through Rate]

[32.38]Coloured and textured imprinted cast in place concrete flooring applying finishing of the top surface by sprinkling of colour hardener @ 2.5 Kg per sqm comply with ASTM C 979, floating and levelling the surface, application of release agent, imprint the design in concrete with imprinting tools, cleaning the surface with water jet (next day) and application of acrylic based sealer for complete finishing. Work included by providing and laying 75mm thick M-30 grade concrete and mixing of Chopped Glass Fibre as per ASTM C 1666/C 1666 M-07 Type II, Filament diameter (ASTM D 578) 14 micron, Filament length 12mm (1/2”), Specific gravity (ASTM D 3800) 2.68 g/cm3, Tensile Strength 1700 Mpa, dosage 600 g/m3 or 85 gms/50 kgs of cement bag, well compaction for necessary finish of top surface, side supports, levelling, pumping, curing compound etc., complete treatment of construction joints by groove cutting of 4mmx 20mm panel size approx 3x3mtr and filling the same with baker road and providing PU joint sealer etc. and as per directions of Engineer-in-charge. [Through Rate]

[32.49]Providing and Fixing in place metallic all embossed Non Fire doors ( Embossed sheet in single side of door) finished with Powder Coating In Regular RAL shades as desired by Engineer- In-Charge. Over all of thickness of the shutter to be 46mm thick manufactured from 0.8mm GPSP Galvanised Steel Sheet confirming to (IS277) with provision of Reinforcement Pad and necessary provision for the receiving appropriate hardwares. The Shutter shall be filled with Paper Honeycomb core in fill . Doors should be Coated with pure polyester/Epoxy Polyester powder having coating thickness of 60-80 micron [Through Rate]

[32.58.2]Providing and fixing thermal insulation on external wall with CFC Free closed cell, high performance rigid Polyurethane Foam(PUF) Insulation Slab conforming to IS: 12436 having density not less than 36±2 kg/m3, thermal conductivity (K-value) 0.021 W/m.K measured at 10 deg. C mean temperature and classified as “not easily ignitable” per BS: 476, Part-5, fixed with the help of adhesive (patch applied) and PVC fastener to the wall surface and all complete as per the instruction of engineer-in-charge 2. 50 mm thick Polyurethane foam(PUF) rigid insulation board [Through Rate]

[32.67.2]Providing and laying on smooth roof surface with CFC free, closed cell free Rigid Polyurethane foam slab over deck insulation conforming to IS -12436 (density of foam being 36±2 kg/m3) having thermal conductivity not more than 0.024 W/m.K, over a coat of cold adhesive like CPRX compound, laying 400 G polythene sheet over PUF slab and providing a wearing course of 40 mm thick cement screed 1: 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) in chequered rough finish, in panels of 2.5 m x 2.5 m and embedding with 24 G wire netting and sealing the joints with polymerized mastic, all complete as per direction of engineer-in-charge 2. 50 mm thick Polyurethane foam (PUF) rigid insulation board [Through Rate]

[4.12.1]Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by Engineer-in-charge. 1. All kinds of soil [Through Rate]

[4.4.1]Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. 1. All kinds of soil [Through Rate]

[6.1.6]Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work below plinth level and up to Floor IV level: 6. 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size) [Through Rate]

[6.14.1]Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) [Through Rate]

[6.33.6]Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect below plinth level Note: Reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work , excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. 6. Thermo-Mechanically Treated bars of grade Fe-500D or more [Through Rate]

[7.20.1]Brick work with common burnt clay modular bricks of class designation 10.5 in foundation and plinth in: 1. Cement mortar 1:4 (1 cement : 4 coarse sand) [Through Rate]

[9.33]Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm ( plus 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length up to 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete up to any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. [Through Rate]