Providing, Installing, Testing Of L.E.D. Street Light and Highmast Tower With Fixture, As Per Various Location of Nagarpalika, At- Jetpur, Under 15(Percentage) Vivekadhin (Year-2026-27)

NAME OF WORK:- PROVIDING, INSTALLING, TESTING OF L.E.D.STREET LIGHT AND HIGHMAST TOWER WITH

FIXTURE, AS PER VARIOUS LOCATION, AT. JETPUR-NAVAGADH

TOTAL AMOUNT PUT TO TENDER

TOTAL AMOUNT PUT TO TENDER

PERCENTAGE RATE TENDER

Sr.No. Schedule Amount

1 Schedule - "B"- 1

2 Schedule - "B"- 2

3 Schedule - "B"- 3

4 Schedule - "B"- 4

Total Amount Rs.

Total Amount Rs.

I/We am/are willing to carry out the work @ ________% Above / Below_____________Percentage (should be

writen in figures and words) of the Estimated rates mentioned above amount of my / our Tender works out as

Estimated Amount Estimated Amount

Put to Tender Rs. 19,70,327=00 Put to Tender Rs. 19,70,327=00

Add …………………….% Rs. Deduct …………………….% Rs.

Total Rs. Total Rs.

(In Words (In Words

Stamp with Signature of Contractor

Cons. Engineer Engineer

"DESIGN POINT" Jetpur-Navagadh Nagarpalika

Chief Officer President

Jetpur-Navagadh Nagarpalika Jetpur-Navagadh Nagarpalika

JETPUR-NAVAGADH NAGARPALIKA - JETPUR

SCHEME : 15% VIVEKADHIN GRANT (YEAR-2026-27)

NAME OF WORK :- PROVIDING AND FIXING 12 MT. HIGH MAST TOWER

Location :- Gondal Daravaja, Opp. Haveli, Near Bhadar Bridge, At. Jetpur

SCHEDULE - "B-1"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

Supplying, erecting, testing commissioning, approved make M.S.

polygonal high mast pole having following general specification. (a)

polygonal section fabricated from M.S plate confirms BSEN 10025 & hot

deep galvanised minimum 65/86 micron (as per IS 01461) lentern

carriage with ring and rubber lines for erection of luminaries of suitable

site.(b) maximum telescopic section not more than four (c) double drum

gear pipe motorised winch with 6mm dia S.S. rod (for 16mtr and above

size) (d) approved make L.E.D. aviation light = 1 no. lighting arrestor =

No. with necessary wiring of 2.5 sq.mm 5 core ISI copper cable

unarmoured. (e) bottom most section suitable for mounting reversible

motor and switchgears having door not more than 1400mm x 300mm with

water proof gasket & hinges & locking arrangement.

(f) pole structure comprises suitable size of reversible motor, cable and

necessary switchgears. With Control panel

(g) bottom section shall have suitable size of thickness supports ribs

foundation bolts nuts etc.(h) item not comprises the cost of lanterns. (i)

necessary cement concrete foundation as per IS including testing &

commissioning of the entire structure for following size of High Mast poles

[1] high mast 12mtr TOP A/F 105mm BOTTOM A/F 360mm, No. of sec.

no.-one, BOTTOM thickness - 3 mm, size base plate- 520x16,

foundation bolt size M24 x 850, Qty-6 nos., suitable for mounting fitting of

light- 6 nos. 1.00 141616.14 Each

Supplying and erecting LED street light / Flood light fittings with High

power White LEDs wattage of 3 Watt and above assembled on single

MCPCB, efficiency more than 130 lm/w and corrosion free High pressure

die cast aluminum housing with smooth finish powder coated and heat

sink extruded aluminium with diffuser and Polycarbonate optics/ lenses,

with toughened glass with company mark/name engraved or embossed

160 to 270 V,Power Factor more than 0.95, THD < 10 %, CCT 3000 K to

5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED

driver efficiency > 85 %.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.)

(A) Street Light (IP-65), Surge protection -4KV integral and ,Light must

have 440VAC line supply with over-voltage protection.

(iv) above 200 to 250 watts, cat - III 6.00 10263.62 Each

Supplying & erecting IP 55 grade following size section pillar fabricated

from joint less M.S. Sheet with angle iron legs made from jointless M.S.

Angle with cable clamps to be buried in ground to have appropriate

erection to work uniform until erected with cement concrete foundation

and 45 cm high bricks work finishing with plaster etc. hinged double door

internally supported on both side, with internal and outside looking

arrangement with look and keys in duplicate 35 x 35 x 5 mm M.S. Angle of

Two Nos. one is welded and other with nut and bolt for erecting Bakelite

sheet. Painting the Section Pillar inside and out side with three tank

powder coated paint. section pillar roof should be without joint with water

leakage proof & tested as per IP 55 test & followed by IS 2147 of

(B) 75 X 60 X 45 cm section pillar fabricated from 16 Guage MS Sheet

with angle iron legs 45 cms long made from 35 X 35 X 5 mm thick MS

Supplying and erecting nuwood 12 mm thick on existing angle iron frame.

Supplying & erecting power contactor for time swich complete erected as

per diration cat III [D] 4 pole 440v. 40amp. 1.00 2782.55 Each

Supplying & erecting approved make Digital time switch having lithium cell

6 years operative and and operate battery backup 1 chennel day clock

with 14 memory programme, suitable to operate on240V+5% 16A with,

floating contacts minimum & LCD display. Also comprised permenet

ON/OFF switching. Programming switches & transparent cover erected as

required with necessary connection erected as directed.

providing and erecting Miniature circuit breaker single pole 6A to 25A

suitable to operate on 240 V A.C. system and having breaking capacity

10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI

Mark 8.00 112.11 Each

Providing Approved make Triple Pole Cast Iron Clad Switch & rewirable

Fuse with neutral link 415/500 V confirming to IS 63 A 2.00 1977.58 Each

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI

marked stranded Copper conductor wire in following type of pipe to be

erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green colour for earth

continuity of following size (b) 2 wire 2.5 s.q. mm 100.00 82.82 Rmt

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

multistrand Aluminium conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of following size of cables

(A) 3 1/2 core 25 Sq. mm ( 16 Sq. mm 1/2 core) 40.00 163.62 Rmt

Making trench in Hard Murrum / Tar Road of suitable width of 90 cm or

required depth for laying any size of cable or locating the fault all over the

run and back filling the same and making the surface as normal ground.

Supplying & erecting earth pit of minimum bore dia.150mm size approved

make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS

3043-1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe

dia of 50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm

having 200-250 Micron galvanising, connection terminal dia of 12mm with

constant ohmic value surrounded by highly conductive compound with

high charge dissipation suitable for following type of applications with

chamber and heavy duty cover.(approved make OEM has to submit test

certificate) & having back filling compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 / meter testing as per IEC 62561-2017,

Voltage drop:- < 1 volt at no load & dry form, Sulphar content:- <2%(C)

Back fill Compound :- Earthing compound should be capable to retain

moisture for long time Necessary test report must be submitted. (a) For

Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Total Amounts Rs.......…

Total Amounts Rs.......…

Stamp with Signature of Contractor

Consl.Engineer Municipal Engineer

"DESIGN POINT" Jetpur-Navagadh Nagarpalika

Chief Officer President

Jetpur-Navagadh Nagarpalika Jetpur-Navagadh Nagarpalika

JETPUR-NAVAGADH NAGARPALIKA - JETPUR

SCHEME : 15% VIVEKADHIN GRANT (YEAR-2026-27)

NAME OF WORK :- PROVIDING AND FIXING 12 MT. HIGH MAST TOWER

Location :- Hindu Smashan Campus, At. Jetpur

SCHEDULE - "B-2"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

Supplying, erecting, testing commissioning, approved make M.S.

polygonal high mast pole having following general specification. (a)

polygonal section fabricated from M.S plate confirms BSEN 10025 & hot

deep galvanised minimum 65/86 micron (as per IS 01461) lentern

carriage with ring and rubber lines for erection of luminaries of suitable

site.(b) maximum telescopic section not more than four (c) double drum

gear pipe motorised winch with 6mm dia S.S. rod (for 16mtr and above

size) (d) approved make L.E.D. aviation light = 1 no. lighting arrestor =

No. with necessary wiring of 2.5 sq.mm 5 core ISI copper cable

unarmoured. (e) bottom most section suitable for mounting reversible

motor and switchgears having door not more than 1400mm x 300mm with

water proof gasket & hinges & locking arrangement.

(f) pole structure comprises suitable size of reversible motor, cable and

necessary switchgears. With Control panel

(g) bottom section shall have suitable size of thickness supports ribs

foundation bolts nuts etc.(h) item not comprises the cost of lanterns. (i)

necessary cement concrete foundation as per IS including testing &

commissioning of the entire structure for following size of High Mast poles

[1] high mast 12mtr TOP A/F 105mm BOTTOM A/F 360mm, No. of sec.

no.-one, BOTTOM thickness - 3 mm, size base plate- 520x16,

foundation bolt size M24 x 850, Qty-6 nos., suitable for mounting fitting of

light- 6 nos. 1.00 141616.14 Each

Supplying and erecting LED street light / Flood light fittings with High

power White LEDs wattage of 3 Watt and above assembled on single

MCPCB, efficiency more than 130 lm/w and corrosion free High pressure

die cast aluminum housing with smooth finish powder coated and heat

sink extruded aluminium with diffuser and Polycarbonate optics/ lenses,

with toughened glass with company mark/name engraved or embossed

160 to 270 V,Power Factor more than 0.95, THD < 10 %, CCT 3000 K to

5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED

driver efficiency > 85 %.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.)

(A) Street Light (IP-65), Surge protection -4KV integral and ,Light must

have 440VAC line supply with over-voltage protection.

(iv) above 200 to 250 watts, cat - III 6.00 10263.62 Each

Supplying & erecting IP 55 grade following size section pillar fabricated

from joint less M.S. Sheet with angle iron legs made from jointless M.S.

Angle with cable clamps to be buried in ground to have appropriate

erection to work uniform until erected with cement concrete foundation

and 45 cm high bricks work finishing with plaster etc. hinged double door

internally supported on both side, with internal and outside looking

arrangement with look and keys in duplicate 35 x 35 x 5 mm M.S. Angle of

Two Nos. one is welded and other with nut and bolt for erecting Bakelite

sheet. Painting the Section Pillar inside and out side with three tank

powder coated paint. section pillar roof should be without joint with water

leakage proof & tested as per IP 55 test & followed by IS 2147 of

(B) 75 X 60 X 45 cm section pillar fabricated from 16 Guage MS Sheet

with angle iron legs 45 cms long made from 35 X 35 X 5 mm thick MS

Supplying and erecting nuwood 12 mm thick on existing angle iron frame.

Supplying & erecting power contactor for time swich complete erected as

per diration cat III [D] 4 pole 440v. 40amp. 1.00 2782.55 Each

Supplying & erecting approved make Digital time switch having lithium cell

6 years operative and and operate battery backup 1 chennel day clock

with 14 memory programme, suitable to operate on240V+5% 16A with,

floating contacts minimum & LCD display. Also comprised permenet

ON/OFF switching. Programming switches & transparent cover erected as

required with necessary connection erected as directed.

providing and erecting Miniature circuit breaker single pole 6A to 25A

suitable to operate on 240 V A.C. system and having breaking capacity

10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI

Mark 8.00 112.11 Each

Providing Approved make Triple Pole Cast Iron Clad Switch & rewirable

Fuse with neutral link 415/500 V confirming to IS 63 A 2.00 1977.58 Each

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI

marked stranded Copper conductor wire in following type of pipe to be

erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green colour for earth

continuity of following size (b) 2 wire 2.5 s.q. mm 100.00 82.82 Rmt

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

multistrand Aluminium conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of following size of cables

(A) 3 1/2 core 25 Sq. mm ( 16 Sq. mm 1/2 core) 40.00 163.62 Rmt

Making trench in Hard Murrum / Tar Road of suitable width of 90 cm or

required depth for laying any size of cable or locating the fault all over the

run and back filling the same and making the surface as normal ground.

Supplying & erecting earth pit of minimum bore dia.150mm size approved

make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS

3043-1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe

dia of 50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm

having 200-250 Micron galvanising, connection terminal dia of 12mm with

constant ohmic value surrounded by highly conductive compound with

high charge dissipation suitable for following type of applications with

chamber and heavy duty cover.(approved make OEM has to submit test

certificate) & having back filling compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 / meter testing as per IEC 62561-2017,

Voltage drop:- < 1 volt at no load & dry form, Sulphar content:- <2%(C)

Back fill Compound :- Earthing compound should be capable to retain

moisture for long time Necessary test report must be submitted. (a) For

Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Total Amounts Rs.......…

Total Amounts Rs.......…

Stamp with Signature of Contractor

Consl.Engineer Municipal Engineer

"DESIGN POINT" Jetpur-Navagadh Nagarpalika

Chief Officer President

Jetpur-Navagadh Nagarpalika Jetpur-Navagadh Nagarpalika

JETPUR-NAVAGADH NAGARPALIKA - JETPUR

SCHEME : 15% VIVEKADHIN GRANT (YEAR-2026-27)

NAME OF WORK :- PROVIDING AND FIXING 12 MT. HIGH MAST TOWER

Location :- Sardar Garden Campus, Tinbatti Chowk, At. Jetpur

SCHEDULE - "B-3"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

Supplying, erecting, testing commissioning, approved make M.S.

polygonal high mast pole having following general specification. (a)

polygonal section fabricated from M.S plate confirms BSEN 10025 & hot

deep galvanised minimum 65/86 micron (as per IS 01461) lentern

carriage with ring and rubber lines for erection of luminaries of suitable

site.(b) maximum telescopic section not more than four (c) double drum

gear pipe motorised winch with 6mm dia S.S. rod (for 16mtr and above

size) (d) approved make L.E.D. aviation light = 1 no. lighting arrestor =

No. with necessary wiring of 2.5 sq.mm 5 core ISI copper cable

unarmoured. (e) bottom most section suitable for mounting reversible

motor and switchgears having door not more than 1400mm x 300mm with

water proof gasket & hinges & locking arrangement.

(f) pole structure comprises suitable size of reversible motor, cable and

necessary switchgears. With Control panel

(g) bottom section shall have suitable size of thickness supports ribs

foundation bolts nuts etc.(h) item not comprises the cost of lanterns. (i)

necessary cement concrete foundation as per IS including testing &

commissioning of the entire structure for following size of High Mast poles

[1] high mast 12mtr TOP A/F 105mm BOTTOM A/F 360mm, No. of sec.

no.-one, BOTTOM thickness - 3 mm, size base plate- 520x16,

foundation bolt size M24 x 850, Qty-6 nos., suitable for mounting fitting of

light- 6 nos. 1.00 141616.14 Each

Supplying and erecting LED street light / Flood light fittings with High

power White LEDs wattage of 3 Watt and above assembled on single

MCPCB, efficiency more than 130 lm/w and corrosion free High pressure

die cast aluminum housing with smooth finish powder coated and heat

sink extruded aluminium with diffuser and Polycarbonate optics/ lenses,

with toughened glass with company mark/name engraved or embossed

160 to 270 V,Power Factor more than 0.95, THD < 10 %, CCT 3000 K to

5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED

driver efficiency > 85 %.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge may select any wattage

capacity between the ranges shown.)

(A) Street Light (IP-65), Surge protection -4KV integral and ,Light must

have 440VAC line supply with over-voltage protection.

(iv) above 200 to 250 watts, cat - III 6.00 10263.62 Each

Supplying & erecting IP 55 grade following size section pillar fabricated

from joint less M.S. Sheet with angle iron legs made from jointless M.S.

Angle with cable clamps to be buried in ground to have appropriate

erection to work uniform until erected with cement concrete foundation

and 45 cm high bricks work finishing with plaster etc. hinged double door

internally supported on both side, with internal and outside looking

arrangement with look and keys in duplicate 35 x 35 x 5 mm M.S. Angle of

Two Nos. one is welded and other with nut and bolt for erecting Bakelite

sheet. Painting the Section Pillar inside and out side with three tank

powder coated paint. section pillar roof should be without joint with water

leakage proof & tested as per IP 55 test & followed by IS 2147 of

(B) 75 X 60 X 45 cm section pillar fabricated from 16 Guage MS Sheet

with angle iron legs 45 cms long made from 35 X 35 X 5 mm thick MS

Supplying and erecting nuwood 12 mm thick on existing angle iron frame.

Supplying & erecting power contactor for time swich complete erected as

per diration cat III [D] 4 pole 440v. 40amp. 1.00 2782.55 Each

Supplying & erecting approved make Digital time switch having lithium cell

6 years operative and and operate battery backup 1 chennel day clock

with 14 memory programme, suitable to operate on240V+5% 16A with,

floating contacts minimum & LCD display. Also comprised permenet

ON/OFF switching. Programming switches & transparent cover erected as

required with necessary connection erected as directed.

providing and erecting Miniature circuit breaker single pole 6A to 25A

suitable to operate on 240 V A.C. system and having breaking capacity

10 KA to be erected in existing box. confirming to IS 8828/1996 with ISI

Mark 8.00 112.11 Each

Providing Approved make Triple Pole Cast Iron Clad Switch & rewirable

Fuse with neutral link 415/500 V confirming to IS 63 A 2.00 1977.58 Each

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI

marked stranded Copper conductor wire in following type of pipe to be

erected concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper

conductor FRLS PVC insulated stranded wire of green colour for earth

continuity of following size (b) 2 wire 2.5 s.q. mm 100.00 82.82 Rmt

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

multistrand Aluminium conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of following size of cables

(A) 3 1/2 core 25 Sq. mm ( 16 Sq. mm 1/2 core) 40.00 163.62 Rmt

Making trench in Hard Murrum / Tar Road of suitable width of 90 cm or

required depth for laying any size of cable or locating the fault all over the

run and back filling the same and making the surface as normal ground.

Supplying & erecting earth pit of minimum bore dia.150mm size approved

make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS

3043-1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe

dia of 50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm

having 200-250 Micron galvanising, connection terminal dia of 12mm with

constant ohmic value surrounded by highly conductive compound with

high charge dissipation suitable for following type of applications with

chamber and heavy duty cover.(approved make OEM has to submit test

certificate) & having back filling compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 / meter testing as per IEC 62561-2017,

Voltage drop:- < 1 volt at no load & dry form, Sulphar content:- <2%(C)

Back fill Compound :- Earthing compound should be capable to retain

moisture for long time Necessary test report must be submitted. (a) For

Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Total Amounts Rs.......…

Total Amounts Rs.......…

Stamp with Signature of Contractor

Consl.Engineer Municipal Engineer

"DESIGN POINT" Jetpur-Navagadh Nagarpalika

Chief Officer President

Jetpur-Navagadh Nagarpalika Jetpur-Navagadh Nagarpalika

JETPUR-NAVAGADH NAGARPALIKA - JETPUR

SCHEME : 15% VIVEKADHIN GRANT (YEAR-2026-27)

NAME OF WORK :- PROVIDING, INSTALLING, TESTING OF L.E.D.STREET LIGHT FIXTURE, BRACKET, CABLE

Location :- Various Location of Jetpur Town, At. Jetpur

SCHEDULE - "B-4"

PERCENTAGE RATE TENDER

Item No. & Description Quantity Rate Per Amount

Providing Street Light pole bracket comprising main B Class MS pipe of

4.2 cm/require outside dia. complete with suitable B Class M.S. sleeve

tubing of approx. 45cms.length and suitable for 76.5 mm /80mm / required

size of pole top having sufficient fastners for fixing the brackets and

having spread of 1.5.mtr. length with 110 deg.with vertical plane & suitable

welded stays, reducer and with check nuts complete painted with one coat

of Red oxide / PU base primer and two coats of Aluminium / PU paint.

paint with following nos of arms. [A] Single Arm Bracket 1.5 Mtr

Supplying and erecting LED street light / Flood light fittings with High

power White LEDs wattage of 3 Watt and above assembled on single

MCPCB, efficiency more than 130 lm/w and corrosion free High pressure

die cast aluminium housing with smooth finish powder coated and heat

sink extruded aluminium with diffuser and Polycarbonate optics/ lenses

with company mark/name engraved or embossed 160 to 270 V,Power

Factor more than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity

ratio >0.45, Luminaire efficacy> 100 lumens/watt . LED driver efficiency >

85 %.( fittings required LM-79 & LM-80 certificates)(NOTE: Below

description have shown ranges of Wattage capacity of LED fittings.The

Engineer incharge may select any wattage capacity between the ranges

shown.) (A) Street Light (IP-65), Surge protection -4KV integral and ,Light

must have 440VAC line supply with over-voltage protection. above 60 to

90 watts Cat-lll 176.00 5976.17 No.

Supplying & erecting XLPE(IS:7098)(I)-88 ISI unarmoured copper cable

1.1 KV grade to be erected as directed of following size. (E) 3 core

Total Amounts Rs.......…

Total Amounts Rs.......…

Stamp with Signature of Contractor

Consl.Engineer Municipal Engineer

"DESIGN POINT" Jetpur-Navagadh Nagarpalika

Chief Officer President

Jetpur-Navagadh Nagarpalika Jetpur-Navagadh Nagarpalika