GE/SMB/T-53/2023-24 SPL REPAIR TO BLDG NO T 19 PROVN OF ADDITION ALTRATION TO BLDG NO T50 AND CERTAIN MINOR AND REVENUE WORKS AT MIL HOSPITAL AREA AND KHETARPAL LINES AT SAMBA UNDER GE SAMBA

Amount

Taking down cement plaster on brick/concrete surfaces or stone walls, ceiling, etc, including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed . NOTE- Work will be carried out upto 3rd storey of bldgs also as per direction of Engr-in-charge including necessary scaffolding required as per site conditions & no extra payment shall be made on this account.

Rendering 15 mm thick cement plaster in cement mortar 1:4 in two layers (10+5mm) on brick /stone/concrete surfaces finished even and smooth without using extra cement (upto 3rd storey with necessary scaffolding), complete all as specified and directed.

Rendering 10 mm thick cement plaster in cement mortar 1:6 on brick /stone/concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position, framed work, complete all as specified and directed.

Roof trusses (framed), trussed, purlins, rafters, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel, flat, hollow sections) including distance pieces, cleats, welding/rivets/nut/bolts/washer etc, conforming to Fe-410-W (Gde-E-250) Quality-'A' ,complete all as specified and as directed.

Dismantling asbestos cement, corrugated or semi-corrugated sheets in roofs incl ridge, complete all as specified.

Pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.50mm thick of approved colour having tensile strength 550 MPa as in roof covering/cladding to wall fixed with self tapping screws including side and end lap as per manufacturer’s instructions complete all as specified and directed.

Pre-painted galvalume aluminium zinc coated GI based plain steel sheet 0.50mm thick of approved colour having tensile strength 550 MPa as in ridges, fixed with self tapping screws including side and end lap as per manufacturer’s instructions complete all as specified and directed.

Designer ceiling board tiles 600x600x4mm thick white prelaminated self embosed reinforced of approved texture at all height laid on Hot dipped Galvanised iron imposed grid with 24 mm wide T-section exposed flanges which shall be power coated white. The frame work shall comprise of main runner made from 0.33mm thick G S sheet and of size 24x32x3000mm and spaced at 1200mm centers securely fixed to the structural soffits by approved hangers at 1200mm maximum centers. Hangers/suspended with 2 run of 2 mm dia of GI wire to be fixed by approved rawl plug, level and justers and screws etc. The last hanger at the end of each main runner shall be greater than 450mm from adjacent wall. Flush fitting of 1200mm long cross tee (with double stitching) to be interlocked between main runners at 600mm center to form 1200x600mm modules cross tee longer than 600 mm to be supported independently. 600x600 mm modulesto be formed by fitting 600 mm long cross Tee centrally between the 1200mm cross tee. Tee, Perimeter wall angle shall be of 0.45mm thick GS sheet of size 19x19mm and 300 mm long of white colour as per manufacturer's instruction including dismantling existing false ceiling board and fittings etc completed all as specified and directed.

Demolition of cement concrete (unreinforced/ Reinforced) ground floor and pavings n exc 15 cm thickness (below or above ground level) and removing the rubbish from the work site out side defence premises complete all as specified and directed.

PCC 1:2:4 type B-1 (using 20 mm graded stone crushed aggregate) as in coping, bed blocks etc complete all as specified and directed.

Demolition of brick work or stone masonry, built in cement mortar incl all quoins, arches pillars etc complete all as specified and directed .

Brick work with sub class 'B' burnt old size bricks straight or curved on plan exc. 6 m mean radius bult in CM 1:6 ,complete all as specified and as directed.

Rotational moulded polyethylene water storage tanks of 500 litres capacity,(cylindrical vertical with closed top) with plastic lid cover, triple layered, white, hoisted and fixed in position all as specified in SSR Part-I including PTMT Ball valves high pressure with epoxy coated Aluminium rod & high density plastic ball complete, screwed for iron pipe or brass ferrule and fixed for 20 mm bore pipe, including making connections and taking down old u/s water tank with fittings, complete all as specified and directed.

20mm bore ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed in repair minimum weight 20 mm size-210 gms),complete all as specified and as directed.

Taking down GI pipe 15 mm bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed

GI water tubing medium grade of bore 15 mm dia with all fitting like as (Elbow, Tee, Sockets, Union, Nipple, and bend etc) on wall for water heater, complete all as specified and directed.

G.I. pipe 15 mm bore tubing medium grade galvanised with all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts etc fixed to wall, ceiling or laid in floors but except pipe complete all as specified and directed

Taking down GI pipe 20 mm bore steel tubing and connections including cleaning for refixing or removal to store complete all as specified and directed

GI water tubing medium grade of bore 20 mm dia with all fitting like as (Elbow, Tee, Sockets, Union, Nipple, and bend etc) on wall for water heater, complete all as specified and directed.

G.I. pipe 20 mm bore tubing medium grade galvanised with all fitting such as bends, tees, elbows, unions, short pieces, connectors, back nuts etc fixed to wall, ceiling or laid in floors but except pipe complete all as specified and directed

Cutting chases,pining in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landing steps, cills, sunshades ,shelves,lintels,etc.; and cutting chases for concealed water tubing or concealed conduit,wiring,etc,and making good cutting not exceeding 10 cm girth in brick walls. complete all as specified and directed.

Dismanting of floor hearth or wall tiling including cement mortar bedding , removing serviceable tiles to store and rubbish off the premises , complete all as specified and directed.

Non - skid Digital Ceramic joint free coloured tiles 8 to 10 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface over and including 15 mm thick screed bed in CM 1:6, Complete all as specied and directed.

Non-skid digital ceramic coloured tiles 8 to 10 mm thick(square/rectangular joint free) , in skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including rendering on brick or concrete surface of wall 10 mm thick screed bed in CM 1:4, complete all as specified and directed

Glazed coloured digital ceramic tiles (1st quality) joint free in vertical surfaces of wall of size 450x300x7mm thick set & jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering in CM 1:4 on brick /concrete surfaces complete all as specified and directed .

Taking down chowkats or frames with shutter (without taking off shutter from the frame) n.exc 1.5 Sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site all as specified and directed.

Taking down chowkats or frames with shutter (without taking off shutter from the frame) exc 1.5 Sqm & n.exc 4 Sqm each including cutting holes for taking out hold fast or dismantling brick work and removing from site all as specified and directed.

Pressed steel frames 125mm x 60mm made out of size 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, hold fast,hinges, lock strike plate, etc and making good in CM 1:3 or cement concrete 1:2:4 Type B-1 including PCC 1:3:6 C-1 as in back filling to chowkhats .complete all as specified and directed .

Pressed steel frames 105mm x 60mm made out of size 1.25 mm thick MS sheet for doors with one or more rebates including necessary fixing lugs, hold fast,hinges, lock strike plate, etc and making good in CM 1:3 or cement concrete 1:2:4 Type B-1 including PCC 1:3:6 C-1 as in back filling to chowkhats .complete all as specified and directed .

Factory made, plain framed, panelled shutter (two Panel) 35mm thick, 2nd class Hardwood with lock rail and panel of 9 mm B.W.P commercial ply. The size of rail and stiles as per as per IS:1003 (Part-I),kiln seasoned and chemically pressure treated complete all as specified and directed.

35mm thick 2nd Class hard wood glazed,gauzed and skelton shutters open rebated and prepare to receive glass, gauge etc but divided into squares with plain chamfered or rounded mitred and rebated sash bars,stiles and rails as specified in SSR Part-I Sec 8 clause 8.24 (a) complete all as specified and directed.

Solid PVC Door Frame of size 50mm x 95mm made out of 5mm Plain colour PVC sheet reinforced with mild steel square tube, supplying and fixing in opening as per specifications and drawing including making good to disturbed surface of walls, complete all as specified and as directed by Engr-in-Charge.

Factory made solid PVC moulded door shutter 28 to 30 mm thick (stiles) with partical board core with 2, 4 or 6 raised panel design with 2 mm thick moulded prelam PVC sheet on the front face & back face to be fitted in the mild steel frame welded / sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site as per specification and drawings.

Factory made steel windows / ventilators double shutter box type, outer frame made out of ERW TUBE 'P' section (60x45x25mm) and shutters of ERW TUBE 'P' section (50x35x20mm) operable shutters side hung includding pistol hinges with two Nos of MS Tower bolts 150mm size on each shutter steel handle and stopper of 'Z' section as specified complete with sash bars devetailed or welded ready for glass fixing and wire gauzed fixing with suitabel fittings/openning for cooler/AC where required .Steel windows will be double shutter external glazed and internal wire gauzed complete all as specifed and as per Drg No CEPZ/TD-324/07 1/3 to 3/3 all as specified and directed by Engr-in-Charge. NOTE: The quoted rate against the above item shall also include (i) 04 Nos MS Steel lugs of 20x5mm MS flat 20cm long over all welded to frames (ii) PCC block for embedding lugs.

Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staple, complete all as specified and directed.

Aluminium alloy, anodised, sliding door bolt Size- 300 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified.

Aluminium handles, fabricated type, anodised Size-150mm, anodised section and fixed complete all as specified.

Aluminium anodised, barrel tower bolts size 200 mm of extruded section and fixed complete all as specified. (ISI Marked)

Aluminium hanging floor door stopper,Twin rubber stopper,size 150mm , anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete all as specified and directed.

Mild steel helical ordinary rat tail rod pattern springs 150mm including roller and roller plate, fixing to pressed steel frames including necessary welding complete inlcuding all as specified and directed

4mm thick sheet glass ordinary quality glazing with oil putty or any type of beads in square n.exc. 0.5 Sq each pane in any type of frame of iron/Steel/Wood/Aluminium as required at site complete all as specified (upto fourth storey with necessary scaffolding), complete all as specified and directed. Make : Saint Gobain, Modi Float, Triveni Float Glass

Preparation of new painted wooden surfaces having width/girth exceeding 10 cm including necessry rubbing with sand paper or grinding by hand grinder to achieve smooth and even surface and applying two coats of synthetic enamel paint over a coat of primer on wooden surfaces of any description ( up to 2nd storey with necessary scaffolding) complete all as specified and directed

Preparation of new painted steel surfaces having width/girth exceeding 10 cm including necessry rubbing with sand paper or grinding by hand grinder to achieve smooth and even surface and applying two coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces of any description ( up to 2nd storey with necessary scaffolding) complete all as specified and directed

Preparation of new surfaces of walls and applying two coats of cement based paint over and including one coat of primer (up to 2nd storey with necessary/scaffolding) complete all as specified and directed by Engr-in-charge.

Preparation of old surfaces of walls and applying one coats of cement based paint (up to 2nd storey with necessary/scaffolding) complete all as specified and directed by Engr-in-charge.

Complete removal of old decorated surfaces including brooming down of steel wire scrapping down smoke foot moulds moss and efflorencet salts and trading oil and grasy spots etc. and applying two coat oil bound distemper over a coat of wall care putty and primer on decorated old plastered or un-plastered surface in walls complete all as specified and directed.

Vitreous China, wash down water closet pan padestral pattern white, excluding fixing bolts, flushing cistern but including flush pipe, seat cover, fixed in repairs complete all as specified and directed.

Vitreous China, wash basin white, flat back , size 500mmx400 including brackets of any size, including cutting for and pinning in ends of brackets or erecting stand including fixing and supply of waste pipe of 32 mm dia, waste coupling of chromium plated brass, fixed in repairs complete all as specified and directed.

PVC valveless,syphonic action type, flushing cistern, low level,white with inlet, ball valve, float and handle including brackets, PVC 32 mm 'L' bend of capacity 10.0 litres and making good to dismantled/damaged floor/surfaces, fixing in repair, complete all as specified and as directed by Engineer-in-charge. Make:- Cera, Cat No- B1010109 ( CONGO) or equivalent model in Jaquar/ Hindware.

15mm bore CP Bib taps, fancy type, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

15mm bore CP Pillar taps, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed in repair, complete all as specified and directed.

15mm bore angle valve with wall flange , cast copper alloy, chromium plated fancy type screwed for 15 mm iron pipe, fixed in repair,complete all as specified and directed.

15mm bore Stop/ cock valves, cast copper alloy,fancy type, chromium plated with long shank and cup (concealed type) screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in repair, , complete all as specified and directed.

Brass chromium plated shower rose with or without swivel joints, 15mm boresize, including fixing to steel pipe or union, fixed in repair, complete all as specified and directed.

Tubular towel rail, 20mm dia, D type, 60cm long between flanges, fixed in repair, complete all as specified and directed.

20mm bore stop ball valves , cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for pipe or for unions and fixed,complete all as specified and as directed.

PVC connection 15 mm x 450 mm including brass check nut at both ends screwed for iron pipe of 15 mm bore fixed in repairs, complete all as specefied and directed.

Sinks with drainage board made of stainless steel 1.00 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm & bowl size 410mm x 355mm x 200mm complete with CP waste coupling & PVC waste pipe complete all as specified and directed by Engineer-in-charge. Make:- Jainko Model No .-SSJ-8. & equivalent model in Prayag, Nirali, Jayana.

Dismantling of PVC(SWR) drain pipes upto 150 mm dia, jointed in cement mortar and taking out of trenches, if required, complete all as specified and directed.

Taking down eaves gutters and PVC rainwater pipes (any size or pattern), including all fittings, heads, shoes, swan-necks, etc including cleaning or refixing or removal to store. (measured overall as fixed along the centre line over fittings and accessories)

PVC (SWR) type B pipes 110 mm bore single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed by Engineer-in-charge.

PVC (SWR) type B pipes 110 mm bore single socketed in any length with rubber ring joints, laid in wall, complete all as specified and as directed by Engineer-in-charge.

UPVC (SWR) type B pipes 75 mm bore single socketed in any length with rubber ring joints, laid in trenches or in floors, complete all as specified and as directed by Engineer-in-charge.

UPVC(SWR) type B pipes 75 mm bore single socketed, in any length with rubber ring joints fixed to walls including stack clamp of GI flat 30mm wide 2mm thick fixed to wall with nail at spacing of 1m center to center , complete all as specified and as directed by Engineer-in-charge.

UPVC (SWR) floor trap plain with grating having dia meter of out let 75mm including jointing with solvent cement to waste pipe fixed in cement concrete type B-1 (1:2:4), fixed in repairs complete all as specified and directed.

UPVC(SWR) , bends for 110 mm bore any radius, complete all as specified and as directed by Engineer-in-charge.

UPVC (SWR) , bends for 75 mm bore any radius , complete all as specified and as directed by Engineer-in-charge.

UPVC(SWR) , bends with access door, for 110 mm bore complete all as specified and as directed by Engineer-in-charge.

UPVC(SWR) , bends with access door, for 75 mm bore complete all as specified and as directed by Engineer-in-charge.

Plain cement concrete 1:4:8 Type D-2 using 40 mm graded crushed stone aggregate as in foundation, sub base of floors , complete all as specified and directed.

75 mm thick cement concrete 1:3:6, type C-2, using 20mm graded crushed stone aggregate as in plinth protection, laid in slope of 1:20 and surface finished even and smooth without using extra cement including making joint at 3m interval and at each corner the joint shall be filled with bitumen mastic filling to full depth (comprising one part hot blown bitumen 85/25 and two part of sand), complete all as specified and directed.

20mm outer dia stainless steel decorative drapery rod of thickness 20 gauge and for every 01 RM length, with stainless steel brackets near to ends with stainless steel finials for 20mm dia drapery rod at both ends. The drapery rod shall be projecting 150 mm outer side from the clear opening of doors/windows. ( Including necessary fittings)

Surface excavation to required camber and gradient n. exc. 30 cm deep and averaging 15 cm deep and getting out in any type of soil, complete all as specified and directed.

Removing excavated material (soil) n exc 50m and depositing where directed at a level n exc 1.5m above the starting point,complete all as specified and directed.

Plain cement concrete 75 mm thick 1:4:8 Type D-2 using 40 mm graded crushed stone aggregate as in sub base of floors , complete all as specified and directed.

Pre-polished chequered cement concrete tiles of size 20 cm x 20cm x 25 mm thick / 25 cm x 25 cm x 25 mm thick, set & jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 20 mm thick cement screed bed in CM 1:6 complete all as specified and as directed.

PCC 1:2:4 type B-0(using 12.5 mm graded stone crushed aggregate) as in roof, padding coping, bed blocks etc complete all as specified and directed.

Forming embankments including raising (or lowering) earth, spreading in layers not exc. 30cm thick, watering, ramming / rolling and finishing to required size, shape etc, n.exc. 1.5 m high from base, complete all as specified and directed.

Hardcore of gauge n.exc. 63 mm, deposited, spread and levelled in layers n.exc. 15 cm thick, watered and well rammed to a true surface, complete all as specified and directed.

Formwork to edges of concrete flates etc exc. 10 cm but not exc. 20 cm wide fair finished, complete all as specified and directed.

Cement concrete 100 mm thick type C-2, 1:3:6 using 40 mm graded crushed stone aggregate as in sub-base of floor and pavings etc, complete all as specified and directed.

Cement concrete 75 mm thick type B-0, 1:1.5:3 using 20 mm graded crushed stone aggregate as in PCC Path, complete all as specified and directed.

Finishing cement concrete surface even and smooth with spike rolling to surfaces or making impressions of expanded metal, whilst the concrete is green without using extra cement, complete all as specified and directed.

Returning, filling in, including spreading levelling, watering and well ramming in layers not exceeding 25 cm in any type of soil complete as specified and as directed by the Engineer-in-Charge.

Complete taking down old aluminium work partition and providing new aluminium work partition wall fixed with 5.5 mm glass 2.0 mtr height and ACP sheet 1.0 mtr height including one aluminium door with floor mechine, complete all as specified and directed.

Demolition of cement concrete as in slab, flooring etc. complete all as specified and as directed.

Excavation in trenches n. exc. 1.5 mtr wide and n. exc. 1.5 mtr in depth for laying of UG cable and getting out in any type of soil complete all as specified and directed . Note :Rates for demoition /excavation in PCC flooring shall be deemed included in quoted rates .No extra shall be paid to the contractor.

Precast cement concrete 1:2:4 Type B-1 1:2:4 using 20 mm graded crushed stone aggregate as in cover slabs, chajjas, shelves and similar articles with plain faces, set in CM 1:4, complete all as specified and directed.

Mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Mild steel TMT bars 6 to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Preparation of new plastered or unplastered surfaces of walls and applying three coats of white washing complete all as specified and as directed by Engineer-in-charge.

Rendering 10 mm thick on concrete surfaces in CM 1:3 on ceiling finished even and smooth without using extra cement , complete all as specified and directed .

Preparation of new plastered or unplastered surfaces of ceilings and applying three coats of white washing complete all as specified and as directed by Engineer-in-charge.

Butt hinges of mild steel cold rolled medium weight of size 100mm complete all as specified and directed

Aluminium anodised, barrel tower bolts size 150 mm of extruded section and fixed complete all as specified. (ISI Marked)

Vitreous China, premium / 1st quality wash down water closet wall hung EWC white / ivory/ offwhite (closed pattern) including all bolts / gel gasket etc. excluding flushing cistern and flush pipe , complete all as specified and directed.

UPVC (SWR) 'S' trap 125/110 mm, setting and jointing with solvent cement complete all as specified.

PVC flush pipe 32 mm bore of polyethylene of low or high density, complete all as specified.

Vitreous china half stall urinal flat back, size 465x355x265 mm white(minimum) with grating and union for discharge pipe (including flush pipe) complete including providing and fixing plugs, bedding urinal against screws, pointing around urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement fixing flushing cistern with brackets, flush pipe, grating and union for discharge pipe, complete all as specified and directed.

UPVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified.

Cement concrete bed to 150 mm internal dia drain pipes including packing under and hunching against the sides of pipes after the area laid and tested in cement concrete 1:3:6 type C-2, complete all as specified and directed.

Cutting existing steel tubing of 15mm bore for alteration are edition (each cut measure)

Cutting existing steel tubing of 20mm bore for alteration are edition (each cut measure)

Gun-metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe of 20 mm bore pipe including making connections, fixed in repair, complete all as specified and directed.

Gun-metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe of 15 mm bore pipe including making connections, fixed in repair, complete all as specified and directed.

Grubbing up vegitation, small tree from roots clean the lose dirt with water, and the reapir the same portion with CM 1:3, touchup with same finish, area n. exc. 0.10 sqm each adjacent to cI pipe with fourth story buldings with necessary scaffolding/ladder, complete all as specified and directed.

Framed work such as grills,gratings etc, with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe.290.Gde-E-165 including fixing in PCC platform, complete all as specified and directed.

Wire neting of galvanised steel wire 2.0mm dia size of mesh 25mm fixed with tinned tacks of wire staples, complete all as specified and directed.

Taking down old unserviceable aluminium point wiring (light, fan, socket , power socket and bulk head fittings) from PVC/metallic conduit,on surface wiring, on wooden batten/casings & caping complete, including fixture and fittings such as switches, ceiling roses,pendents holder, regulators, sockets and defective main switch/DB/MCB/Metal plug etc. by unscrewing carefully from boards etc complete all as specfied and directed.

Point wiring for one light/ fan/ exhaust fan controlled by one switch with 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor (FRLS) in and including PVC concealed conduit having thickness not less than 1.8 mm with sunken box having thickness not less than 2.0 mm thickness with 3 mm bakelite laminated socket ISI marked for switches and sockets , including 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor (FRLS) as earth continuity conductor connected to comman earth dolly in and including cutting chiseling for concealed piping as required and making good disturbed surface area and white wash /colour wash to matching with the existing colour and all as specified and directed . Note: (a) Insulation test of point wiring (b) colour coding is to be maintained .(Ph-Red, N-Black, Half -Yellow, Earth- Green)

Ditto all as per srl item No 112 above but for call bell point, complete all as specified and directed.

Ditto all as per srl item No 112 above but for 3 pin 5 amps on independent board complete all as specified and directed.

Ditto all as per srl item No 112 above but for 3 pin 5 amps on same board complete all as specified and directed.

Point wiring for one light/ AC/Deep Frezzer power point controlled by one switch with 2.5 sqmm single core PVC insulated unsheathed multistranded copper conductor (FRLS) with in and including PVC concealed conduit having thickness not less than 1.8 mm with all fittings including anodise pressed steel sunken box having thickness not less than 2mm with 3mm bakelite laminated sheet ISI marked for switches and sockets , including 2.5 sqmm single core PVC insulated unsheathed multistranded copper conductor (FRLS) as earth continuity conductor connected to comman earth dolly in and including cutting chiseling for concealed piping and making good disturbed surface area and white wash /colour wash to matching with the existing colour and all as specified and directed. Note: (a) Insulation test of point wiring (b) colour coding is to be maintained .(Ph-Red, N-Black, Half -Yellow, Earth- Green)

Switch piano flush type one way 5 amps SP complete all as specified and directed.

Switch piano flush type single pole 15 Amp, one way, AC 230 volts SP complete all as specified and directed.

Socket outlet 3 pin 5 amps flush type complete all as specified and directed.

Switch Socket multipurpose 2 in 1, 6 pin 6 and 16 amps controlled by one switch flush type universal.

Bell push flush type with indicator, 6 Amps, complete all as specified and directed.

Electronic bell ding-dong, AC 230 volts, SP, complete all as specified and directed.

Ceiling rose 65 x 50mm three terminals complete all as specified and directed.

Ceiling fan regulator electronic type 5 stage speed variation,socket type is size, ISI marked complete all as specified and directed.

Lamp holder/batton holder/angle holder insulated body(Metal ring) with back bakelite plate suitable for batten fittings, complete all as specified and directed.

LED tube light fitting 20 watt, 230 volt,box type complete bipin holders, connector block and retro LED rod of 20 watt polycarbonate diffuser having high efficacy (single side connection) complete with all accessories internally pre wired batten(single side connection) including connecting up with three core twisted flexible copper conductor cable of suitable size and mounted on PVC square block complete all as specified and directed,LED tube rod ,make :Havells ,cat part no: TITANIANEO1213T8SSTL20WLED865SPC and LED tube light batten ,make :Havells ,cat part no: REGALBATTANT8UPTO1X22WSSBSWH or technocommerically equivalant make of Crompton/Philips/Halonix/Benlo. Note: (i) Contractor shall produce LM 79 & LM 80 test report form OEM owned NABL accredited laboraory. (ii) Contractor shall give gurantee of complete fitting/ fixtures for minimum of 2 years form the date of completion. (iii) Contractor shall conduct the inspection of company representative at site before installation of fittings/fixtures at no extra cost.

Environmental friendly, ultra modern, energy saving, surface mounted, decorative hexagon bulk head Back-lit LED luminaire comprising of high brightness LEDs. suitable for 10W IP-66 Make: Havells ,cat part no :HEXAFT10WLED857SSYMBOPC or technocommerically equivalant make of Crompton/Philips/Halonix/Benlo.

Sheet metal enclousre for DBs when MCB to be used double door powder coated factory made flush fixed complete with 200 amps rated bus bar 240 volts single phase 12 ways complete all as specified and directed,

MCB SP 6 to 32 Amps 240 Volt 'B' series complete all as specified and as directed.

MCB SPN 63 Amps 240 Volt 'B' series complete all as specified and directed.

Supply, laying and testing cable XLPE insulated, screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor of sixe 10 sqmm 2 core complete all as specified and directed.

Earthing complete with galvanized steel earth plate electrode 600x600x6mm thick buried directly in the ground (earth pit not less than 2.25 mtr deep below the normal ground level ) with top edge of plate not less than 1.5 mtr below the normal ground level connected to galvanized iron wire 4mm dia as earth lead by means of nuts bolts,washers of GI upto test point,GI tubing light grade 15mm bore protection pipe and GI watering pipe 20mm light grade with funnel and wire mesh ,charcoal and salt,40mm thick pre-cast RCC M-15 (nominal mix) cover reinforced with XPM weight not less than 4 kg /sqm with suitable handle of 6mm dia MS bar and angle iron 40x40x3mm frame for cover ,PCC M-15 (nominal Mix) pit,excavation and earth work in any type of soil and removing surplus soil to a distance n.exc.50m) and connecting, Testing on complition, Complete all as specified and shown on Electrical Plate No 3 of SSR-2009 Part-1. complete all as specified and directed. Notes:- 1. Earth lead & protection pipes length upto & including 7.50 mtr is included in the quoted rate. 2. Soil should be free from stone, boulders, aggregate, gravels etc.

Sand cushioning to under ground electric cable a layer of 8 cm thick before laying the cable and 15 cm thick after laying and stretching the cable complete all as specified in clause 19.75 of MES Schedule part-I (2009) Note : Sand shall be of good quality as specifed and punned thickness shall be measured and paid.

Material and labour for sub class 'B' bricks well burnt old size laid dry flat for protection of cable complete all as specifeid and directed.

GI pipe in replacement ( Light grade ) for protection of LT cable fixed to walls/ poles/road crossing including suitable size clamps complete of size 40 mm bore , complete all as specified and directed

Recess mounting LED 2x2 luminaire 36 watt light fitting complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of 1.5 Sqmm with suitable size of 36 watt, complete all as specified and directed.

Sheet metal enclosures distribution boards, double door ,VTPN, 415 volts 4 ways (one incoming three phase & twelve out goings single phase )for MCCB & MCB,s comprising three phase four wire copper strip bus bar of appropriate capacity complete all as specified and directed and comprising of the following a) MCCB FOUR POLE 100 AMPS AC 415 VOLTS 25 KA=01 NO (for incoming ) (b) MCB SPN 63 amps = 01 Nos (b) MCB SP 6 to 32 amps = 5 Nos (for outgoings) . Note :- (i)The DB shall be VTPN series of Make : Schneider ,cat part no: A9HVD04L or equivalent make of L&T/ ABB/ Legrand/BENLO . (ii) The DB shall be flush fixed and making good the disturbed surface matching with existing specifications shall be part of job at no extra cost. (iii)connection of the MCCBs/ MCBs with cable shall be made through appropriate size pin /bottle type thimble properly crimped. (iv) All the vacant holes of the DB shall be provided with blank plates of appropriate size. (v) Double continuous earth wire shall be provided for each three phase DB from earthing mains dolly. (vi) cutting chasing shall be part of job at no extra cost .

Submain wiring in and including PVC conduit 1.8 mm thick ,20 mm dia with two run of PVC insulated, unsheathed multistranded copper conductor of 4 sqmm(FRLS) and one run of PVC insulated,unsheathed multistranded copper conductor 4 sqmm (green in colour) for earth continuity conductor and connected to common earth dolly with thimble etc including taking down old U/S brunt sub main wiring from wooden battens, complete all as specified and directed. (Two run of 4 sqmm plus one run 4 sqmm of earth wire will be measured as 1RM) Note: (a) Insulation test of point wiring (b) colour coding is to be maintained .(Ph-Red, N-Black,Earth- Green)

Water heater (gyser) storage type , electric, capacity 25 ltr, BEE 5 star rated with set of hot and cold flexible connection pipe and connecting electrically, complete all as specified and directed. Make - Standred, Cat part no. Amazer-H 25 ltr white or technocommercially equivalent of Havells/Bajaj.

AC hi wall split units indoor / outdoor (Hot & Cold) complete with cordless remote control units and with in built air ioniser and plasma filter for better indoor air quality with minimum 5 star rating and EER 3.2 of capacity of 1.5 ton, complete with all connection and specified and directed.

Single pole and neutral enclosere with a two pin and earth plug and socket complete with one single pole 20 Amps MCB, complete all as specified and directed.

Ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 volts, 1200 mm sweep, minimum air delivery 210 CFM with service valve 6.00 BEE, 5 star rating, with brushless direct current motor (BLDC), complete all as specified and directed.

Supply, installation and commissioning of refrigerators, electric driven (single phase) double door, of capacity 320 ltr, BEE 5 star rated including point wiring & connection, complete all as specified and directed.

Supply, installation and commissioning of deep freezer hard top, double door, single phase 240 volts, 50 Hz of capacity 400 ltrs including point wiring & connection, complete all as specified and directed.

Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 90 V to 280 V with output voltage stabilizer at 230 V with accuracy of ( -) or (+) 2.5% and of capacity 2 KVA including all connection , complete all as specified and directed.

Supply, installation and commissioning of desert cooler, stand / trolley mounted with castor wheels plastic body tank capacity 47 ltr synthetic honeycomb pads normal air delivery 3000 cubic meter per hour power consumption 210 W fan size 400 mm for 4000 nominal capacity , complete all as specified and directed. Make - Crompton/Usha/Symphony/Voltas/Bajaj

Supply, installation and commissioning of water cooler, partially stainless steel, electric driven single phase having approx storage 40 ltr and nominal cooling capacity 80 ltr including point wiring and all connection, complete all as specified and directed.

Supply, installation and commissioning of water purification system based on Reverse Osmosis mechanism of out put capacity of 50 ltr per hour with RO+UV+UF+TDS Control and filter change alarm, with double RO membrance in pre bowl including all standard fittings and fixture with point wiring and all connection, complete all as specified and directed. Make - KENT/AQUA FRESH/ SATHAYA SAYA AQUA PURA.

Switch Socket combination 2 in 1, 3 pin, 6 and 6 amps, flush type universal, complete all as specified. .

Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 90 V to 280 V with output voltage stabilizer at 230 V with accuracy of ( -) or (+) 2.5% and of capacity 1 KVA including all connection , complete all as specified and directed.

Air circulator fans 230 volts, single phase, oscilating 450 mm sweep suitable for wall mounting including all connection, complete all as specified and directed. Make - Havells or or technocommercially equivalent of Bajaj/Crompton

Note:- The contract sum arrived after deduction of amount of Sch of credit as listed in tender Documents.

SIDDAHANT ENTERPRISES

s k construction co

Ms International Engineers