COMPREHENSIVE MAINTENANCE TO HIGH RISE BUILDINGS IN NEW NSB UNDER AGE B R-II OF GE NB, VISAKHAPATNAM

Amount

Taking down Cement Plaster of any description on brick or stone walls or concrete surfaces etc including raking out joints, hacking for key scrubbing down with water etc and removing rubbish to a distance not exceeding 1.5 KM complete all as specified and as directed.

Demolition of Brick / Stone Masonry built in Cement Mortar including all quoins arches pillars etc complete all as specified and as directed.

M & L for brick work with Fly Ash bricks, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

M & L for brick work in half brick thick walls using Fly Ash bricks straight or curved on plan to any radius built in Cement Mortar 1:4 including 2 Nos of 8mm dia bars at every fourth course of brick work complete all as specified and as directed.

M & L for applying Polymer Modified Mortar made using Shrinkage Compensated Polymer Modified Fibre Reinforced Cementitious Repair Mortar such as Renderoc SP 40 of M/s. Fosroc Chemicals India [P] Ltd. or equivalent in M/s. Sika India Pvt. Ltd. or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd. as per manufacturer's instructions to form average 25 mm thick even surface complete all as specified and as directed.

M & L for Non-Shrink, Cementitious Micro Concrete with compressive strength not less than 50 N/ Sq.mm at 28 days as in structural strengthening of existing columns, beams and similar structural members using Rendroc RG' manufactured by M/s. Fosroc Chemicals India [P] Ltd. or its equivalent in M/s. Sika India Pvt. Ltd. or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Bostik India Pvt. Ltd. or M/s Asian Paints Ltd. modified with 12mm graded, clean, saturated surface dry crushed stone aggregate in the ratio as per manufacturer's instructions, laid in columns, beams and similar structural members including use and waste of water tight formwork to facilitate pouring of micro concrete complete all as per manufacturer's instructions including providing double scaffolding and safety measures as required and removal of the same on completion complete all as specified and as directed. Note: Measurement shall be considered for circumference at centreline of core thickness.

M & L for providing additional reinforcement using High Strength Corrosion Resistant Deformed TMT Bars of Grade Fe–500D by checking the diameter of the existing bars, cutting the necessary main reinforcement to the required length with proper development length, tying / binding / welding with the existing shear connectors / reinforcement so that the additional reinforcement acts monolithically with the existing reinforcement and core concrete complete all as specified and as directed. Note: The shear reinforcement shall also be provided as specified here-in-above in the form of 2 "U" shaped bars if existing shear reinforcement is found deteriorated / diameter of the bars is reduced. Diameter of the new bar shall be equal to the existing bars. Additional reinforcement shall be provided only in case the diameter of the existing bars is found less than 30% of the original diameter.

M & L for rendering to brick / concrete surfaces, 15 mm thick in Cement Mortar 1:4, including mixing water proofing compound as per manufacturers instructions and finishing the top surface even and smooth without using extra cement complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

M & L for rendering to brick / concrete surfaces, 10 mm thick in Cement Mortar 1:6, surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for rendering 5 mm thick in Cement Mortar 1:3 on fair faces of concrete surface of ceiling surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M & L for preparing newly plastered wall surfaces by using vaccume based sanding machine and applying two coats of Acrylic washable Distemper by using auto roller/airless sprayer, over a coat of alkali resistant primer over 1mm thick Cement based Wall Care Putty on walls by using multipurpose mixture for proper mixing of putty and putty sprayer for application of putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces complete all as specified and as directed. Note:- The contractor shall carryout Distempering & allied works under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Distempering & allied works through their authorised applicators before commencement of the work to GE for approval.

M & L for Two coats of Weather Proof Exterior Emulsion Paint [100% Acrylic] by using auto roller/ airless sprayer over a Coat of Exterior Primer over 1 mm thick of Cement based Wall Care Putty [primer and putty shall be of same manufacturer as that of exterior emulsion paint] by using multipurpose mixture for proper mixing of putty and putty sprayer for application of putty on newly plastered walls/ ceiling, pillasters, bands, borders, soffits of chajjas and projections including rubbing with sand paper to obtain a smooth surface complete all as specified and as directed. Note:- The contractor shall carryout Exterior Emulsion Painting and allied works under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Exterior emulsion painting through their authorised applicators before commencement of the work to GE for approval.

M & L for preparing newly plastered ceiling surfaces and applying three coats of white washing complete all as specified and as directed.

Taking down and Refixing of wooden shutter in the same or other opening shutters of any description exceeding 1.00 Sq.m but not exceeding 2.00 Sq.m each after easing and adjusting complete all as specified and as directed.

Taking down and Refixing of wooden shutter in the same or other opening shutters of any description not exceeding 1.00 Sq.m each after easing and adjusting complete all as specified and as directed.

Dismantling of Mild Steel or Wrought Iron Work of any description not otherwise provided for complete all as specified and as directed.

S & F Mild Steel work conforming to Fe - 290, Grade E-165 as in Bands, Straps, Supports or Stays for Rainwater, Ventilating Pipes, including Bolts, if required, Hooks [Stay], heavy, for Large Gates, Hook and Pintle Hinges, large Hasps and Staples, Chains, hand made Sliding Bolts, Clamps, Hold Fasts, Wall Ties, Hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles complete all as specified and as directed.

M & L for two coats of Synthetic Enamel paint over one coat of Red Oxide / Zinc Chrome Primer on new steel surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

S & F 150 mm bore Cast iron spun pipe of soil, waste and vent pipes in any length with or without ears, with cement joints, fixed to walls including taking down existing unserviceable CI pipe of any dia with fittings complete all as specified and as directed.

S & F 100 mm bore Cast iron spun pipe of soil, waste and vent pipes in any length with or without ears, with cement joints, laid in floors or trenches including taking down existing unserviceable CI pipe of any dia with fittings complete all as specified and as directed.

S & F 100 mm bore Cast iron spun pipe of soil, waste and vent pipes in any length with or without ears, with cement joints, fixed to walls including taking down existing unserviceable CI pipe of any dia with fittings complete all as specified and as directed.

M & L for jointing only 100 mm bore cast iron pipes and fittings or AC pipes and fittings, in repairs, with cement joints complete all as specified and as directed.

M & L for jointing only 150 mm bore cast iron pipes and fittings or AC pipes and fittings, in repairs, with cement joints complete all as specified and as directed.

S & F 100 mm dia out let, Cast Iron Floor Trap with grating including jointing to waste pipe fixed in cement concrete 1:2:4, Type B-1 complete all as specified and as directed.

S & F 100 mm bore Cast Iron Nahani Trap with grating including jointing to waste pipe, fixed in cement concrete type B1, 1:2:4 complete all as specified and as directed.

S & F Cast Iron Bends [any radius], diminishing pieces or tapers [larger bore measured] of 150mm bore, for Cast Iron soil / waste / vent pipes complete all as specified and as directed.

S & F Cast Iron Branch pieces of 150 mm bore (T or Y ), single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete all as specified and as directed.

S & F Cast Iron Bends [any radius], diminishing pieces or tapers [larger bore measured] of 100mm bore, for Cast Iron soil / waste / vent pipes complete all as specified and as directed.

S & F Cast Iron Branch pieces of 100 mm bore (T or Y ), single (equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches with oval access door complete all as specified and as directed.

S & F Stack clamps made out of 50 X 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 150mm dia pipes complete all as specified and as directed.

S & F Stack clamps made out of 50 X 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100mm dia pipes complete all as specified and as directed.

S & F 110mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, fixed to walls including necessary brackets, clamps as in rain water down pipes including taking up / down unserviceable / cracked rain water pipes including taking out joints of any type complete all as specified and as directed.

S & F 110mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints,laid in trenches or in floors including necessary brackets, clamps as in rain water down pipes including taking up / down unserviceable / cracked rain water pipes including taking out joints of any type complete all as specified and as directed.

S & F 75mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints, fixed to walls including necessary brackets, clamps as in rain water down pipes including taking up / down unserviceable / cracked rain water pipes including taking out joints of any type complete all as specified and as directed.

S & F 75mm bore PVC [SWR] pipes single socketed, in any length with rubber ring joints,laid in trenches or in floors including necessary brackets, clamps as in rain water down pipes including taking up / down unserviceable / cracked rain water pipes including taking out joints of any type complete all as specified and as directed.

S & F 75mm outlet PVC [SWR] Floor Trap with grating including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Junction Single [Single "T"] equal or unequal with access door including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Bends of any radius with access door including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Bends of any radius including jointing with solvent cement complete all as specified and as directed.

S & F 75 mm bore PVC [SWR] Junction Single [Single "T"] equal or unequal with access door including jointing with solvent cement complete all as specified and as directed.

S & F 75 mm bore PVC [SWR] Bends of any radius with access door including jointing with solvent cement complete all as specified and as directed.

S & F 75 mm bore PVC [SWR] Bends of any radius including jointing with solvent cement complete all as specified and as directed.

S & F 110 mm bore PVC [SWR] Vent Cowl including jointing with solvent cement complete all as specified and as directed.

Taking down or up steel tubing and connections for 15 mm bore of pipe complete all as specified and as directed.

Taking down or up steel tubing and connections for 20 mm bore of pipe complete all as specified and as directed.

Taking down or up steel tubing and connections for 25 mm or 32 mm bore of pipe complete all as specified and as directed.

Taking down or up steel tubing and connections for 40 mm or 50 mm bore of pipe complete all as specified and as directed.

Refixing old steel tubing of 15 mm bore and connections in new or old position in wall,ceiling,floor etc. complete all as specified and as directed.

Refixing old steel tubing of 20 mm bore and connections in new or old position in wall,ceiling,floor etc. complete all as specified and as directed.

Refixing old steel tubing of 25 or 32 mm bore and connections in new or old position in wall,ceiling,floor etc. complete all as specified and as directed.

Refixing old steel tubing of 40 or 50 mm bore and connections in new or old position in wall,ceiling,floor etc. complete all as specified and as directed.

S & F GI water tubing of 15 mm bore, medium grade conforming to IS - 1239 [Part - 1] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing, complete all as specified and as directed.

S & F GI water tubing of 20 mm bore, medium grade conforming to IS - 1239 [Part - 1] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing, complete all as specified and as directed.

S & F GI water tubing of 25 mm bore, medium grade conforming to IS - 1239 [Part - 1] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing, complete all as specified and as directed.

S & F GI water tubing of 40 mm bore, medium grade conforming to IS - 1239 [Part - 1] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing, complete all as specified and as directed.

S & F GI water tubing of 50 mm bore, medium grade conforming to IS - 1239 [Part - 1] including all fittings such as bends, tees, short pieces, connectors, elbows, reducers, union, sockets etc fixed to walls, ceiling or laid on floors including testing, complete all as specified and as directed.

S & F in repairs 32mm outer dia of pipe, 3–layer PP–R Polypropylene random copolymer] concealed pipes of SDR 7.4 & SDR 11 UV stabilised and anti microbial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings complete to walls, ceilings or in floors etc. including testing complete all as specified and as directed.

S & F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening complete all as specified and as directed.

Dismantling of stone slabs and tiles in flooring, apron etc of any description or thickness laid dry and pointed in any mortar complete all as specified and directed.

M & L for Granite Stone Slabs of 18 to 20 mm thick of Colour Mexican Red / Ruby Red / Z Black / Pearl Black as in Skirting, Dado, Risers of Steps, Jambs, Pillars, Wall Lining [Veneering to Wall] etc. with machine cut edges, Table rubbed and prepolished to smooth mirror finish all to required sizes, granite stone slabs shall be of design / pattern as directed, including diagonals, inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and bedded with grey cement [slurry] and jointed and pointed flush using polymer based cementitious tiling joint filler to match the shade of the Granite Slabs over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: Single stone slab shall be used for entire height of Skirting / Dado / Risers and joints shall match with the flooring.

M & L for Granite Stone Slabs of 18 to 20 mm thick of Colour Mexican Red / Ruby Red / Z Black / Pearl Black as in Floors, Treads of Steps, Window Cills, Cooking Platform etc., and the like with machine cut edges, Table rubbed and prepolished to smooth mirror finish all to required sizes, granite stone slabs shall be of design / pattern as directed, including inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and bedded with grey cement [slurry] and jointed and pointed flush using polymer based cementitious tiling joint filler to match the shade of the Granite Slabs including screed bed or bedding layer of mortar 20 mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: Single stone slab shall be used for entire Width and Length of Steps, Window Cills, Cooking Platform etc. and joints shall match with the flooring. The edges of treads shall be bull nosed / half rounded. The edges of the treads and landings shall also be provided with three Nos of grooves.

M & L for Marble Stone Slabs of 18 to 20 mm thick of Green Colour as in Flooring, Treads and Risers of Steps, Landings of Staircase etc. with machine cut edges, Table rubbed and prepolished to smooth mirror finish all to required sizes, slabs shall be of design / pattern as directed, including inlays, borders, margins, set and bedded with grey cement [slurry] and jointed and pointed flush using polymer based cementitious joint filler to match the shade of the Slabs including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:6 complete all as specified and as directed. Note: Single stone slab shall be used for entire width of Steps, Risers & Landing etc. and joints shall match with the flooring. The edges of treads shall be bull nosed / half rounded. The edges of the treads and landings shall also be provided with three Nos of grooves.

M & L for Kota Stone Slabs of 20 to 25 mm thick as in Floors, Gallery platforms,Steps, etc. with machine cut edges, including diagonals, inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and bedded with Grey Cement [slurry] and jointed and pointed with grey cement slurry mixed with a admixture of pigment to match shade of Slabs, rubbing and grinding with mechanical equipment fitted with suitable grit size corborundum stones and polishing with Oxalic Acid to smooth, bright mirror finish over screed bed of 15mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: Single stone slab shall be used for entire width of Platforms, Steps, etc.

M & L for Kota Stone Slabs of 20 to 25 mm thick in vertical surfaces of Gallery platforms, Skirting, Dado, Risers of Steps, Jambs, Pillars etc. with machine cut edges, including diagonals, inlays, borders, margins in two or more colours / shades, designs / patterns of stone slabs, set and bedded with Grey Cement [slurry] and jointed and pointed with grey cement slurry mixed with a admixture of pigment to match shade of Slabs, rubbing and grinding with mechanical equipment fitted with suitable grit size corborundum stones and polishing with Oxalic Acid to smooth, bright mirror finish over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: Single stone slab shall be used for entire height of skirting / dado / risers and joints shall match with the flooring.

Dismantling of Floor, Hearth or Wall Tiling of any description including Cement Mortar bedding [but not backing] and removing serviceable tiles to the stores and removing rubbish / debris to a distance exceeding 1.5 KM but not exceeding 5.00 KM complete all as specified and as directed.

M & L for Joint Free Glazed Ceramic Tiles, Edge Cut, Concept Type, Coloured, Premium Quality, of size 450 mm X 300 mm , 7 to 8 mm thick as in Vertical Surfaces such as Skirting, Dado etc set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Joint Free Glazed Ceramic Tiles, Edge Cut, Concept Type, Coloured, Premium Quality, of size 200 mm X 300 mm , 7 to 8 mm thick as in Vertical Surfaces such as Skirting, Dado etc set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in Cement Mortar 1:4 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Non Skid Ceramic Tiles, Joint Free, Coloured, Premium Quality of size exceeding 0.06 Sq.m and not exceeding 0.11 Sq.m, 7 to 8 mm thick [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:6 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Non Skid Ceramic Tiles, Joint Free, Coloured, Premium Quality of size exceeding 0.11 Sq.m and not exceeding 0.18 Sq.m, 7 to 8 mm thick [Square or Rectangular] as in Floors etc, set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:6 complete all as specified and as directed. Note: The colour / shade / design of tiles shall be as approved by GE.

M & L for Non Skid Ceramic Tiles, Joint Free, Coloured, Premium Quality of size exceeding 0.11 Sq.m and not exceeding 0.18 Sq.m, 7 to 8 mm thick [Square or Rectangular] as in Vertical Surfaces such as Skirting, Dado etc set and jointed in neat cement slurry and pointed flush using polymer based cementitious tiling joint filler to match the shade of the tile over backing coat of 10mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note:-The colour / shade / design of tiles shall be as approved by GE.

M & L for providing and injecting chemical emulsion for Post Constructional Anti - termite Treatment at points of contact of wood work by chemical emulsion [in oil or kerosene based solution] @ 0.5 litre per hole by drilling 6 mm dia holes at a downward angle of 45 degrees at 150 mm centre to centre and sealing the same complete all as specified and as directed.

M & L for providing and injecting chemical emulsion for Post Constructional Anti - termite Treatment along external walls where the apron is not provided using chemical emulsion @ 7.5 litres per Sq.m of the vertical surface of sub - structure to a depth of 300 mm by 12 mm dia holes at 150 mm centre to centre both ways including excavating channel along the wall and rodding etc complete all as specified and as directed.

M & L for providing and injecting chemical emulsion for Post Constructional Anti - termite Treatment of soil under existing floors using chemical emulsion @ 1 litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 to match the existing floors complete all as specified and as directed

Taking down framed work such as grill gratings etc to facilitate repair to window etc and refixing after repair with new screws complete all as specified and as directed.

Taking down Chowkats or frame with shutters [without taking off shutter from the frame] not exceeding 1.5 Sq.m each complete all as specified and as directed.

Taking down Chowkats or frame with shutters [without taking off shutter from the frame] exceeding 1.5 Sq.m but not exceeding 4.00 Sq.m each complete all as specified and as directed.

Taking down shutters of any description not exceeding 1 Sq.M each and removing to or from store.complete all as specified and as directed.

Taking down shutters of any description exceeding 1 Sq.M but not exceeding 2 Sq.M each and removing to or from store.complete all as specified and as directed.

Taking down aluminium window shutters not exceeding 1.5 sqm each complete all as specified and as directed.

S & F Second Class Hard Wood, plain, solid, straight Chowkats and Frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joints complete all as specified and directed.

S & F Factory made 35mm thick, Second Class Hard Wood, Plain framed, Panelled Shutter [Two Panel] with Lock Rail and Panel of 9 mm BWP Commercial Ply or 12 mm Veneered Particle Board with Commercial Veneering on both faces, the size of Rail and Stile as per IS – 1003 [Part – I], Kiln Seasoned and Chemically Pressure treated and fitted to Chowkats complete all as specified and as directed.

S & F 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S & F 35mm thick Factory made, Second Class Hard Wood, Glazed and Skeleton Shutters, open rebated and prepared to receive glass, gauze, etc., divided into squares, with plain, chamfered or rounded, mitred and rebated Sash Bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part – I, Section 8, Clause 8.24 [a] and fitted to Chowkats complete all as specified and as directed.

S & F 30mm thick Factory made, Second Class Hard Wood, Glazed and Skeleton Shutters, open rebated and prepared to receive glass, gauze, etc., divided into squares, with plain, chamfered or rounded, mitred and rebated Sash Bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part – I, Section 8, Clause 8.24 [a] and fitted to Chowkats complete all as specified and as directed.

S&F aluminium powder coated window frame with shutters sliding pattern consisting of three tracked frame and 03 shutters (2shutters glazed with 4mm thick tinted glass fixed with suitable EPDM rubber beading and one shutter with stainless steel mosquito proof wire cloth made of 0.36mm nominal dia wire and average aperture 1.4mm) including F Aluminium powder coated grill of make "Deco grill" weight not less than 1.30 kg/ Sqm , suitable 'F' or 'E' sections fixed to window frame for securing Deco grill and necessary handles/locking arrangements for shutter of Jindal sections Window Frame( Top & Sides) : 21137, Bottom L 20977, Window shutters : Top & Bottom : 20567, Sides : 20738 or equivalent of Hindalco & Indalco complete all as specified and as directed.

S & F Solid PVC door frame of size 50mmX47mm made out of 5mm wood grain printed PVC sheet reinforced with MS square tube fixed in opening including edges painted to match with printed sheet complete all as specified and as directed.

S & F Factory made Solid PVC door frame of size 100mmX45mm made out of 5mm plain colour PVC sheet reinforced with MS square tube fixed in opening including edges painted to match with printed sheet complete all as specified and as directed.

S & F Factory made solid panel PVC door shutter 30 mm thick [Style] consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded wood grain printed PVC "C" Channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of wood grain printed PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with 5mm thick x 15mm wide PVC sheet beading used inside stiles and rails and decorative PVC beading of 10mm x 10mm (90°), and joined together with solvent cement fixing in frame at site as per specification complete all as specified and as directed.

S & F PVC solid ventilator frame size 55 X 47mm with wall thickness of 5mm made out of extruded 5mm PVC sheet, mitre cut at two comers and jointed with 2 Nos of 150mm long brackets of 15 x 15mm MS square tube the two vatted profiles are to be reinforced with 19 x 19mm MS squre tube the 50% of bottom portion is fixed with 4mm pin headed glass and balance 50% of top portion is fixed with 4mm thick pin headed glass louvers and cover with 0.36mm dia stainless steel wire mesh at top portion including necessary PVC beading with screws and 3 Nos 12mm dia MS guard, bars fixed in ventilator frame including two coats of synthetic enamel paint over a coat of red oxide primer to MS guard bars etc complete all as specified and as directed. Note:-(Make SINTEX or epuivalent approved make)

S & F Aluminium anodised barrel Tower Bolt of size 150 mm size of extruded section complete all as specified and as directed.

S & F Aluminium anodised barrel Tower Bolt of size 100 mm size of extruded section complete all as specified and as directed.

S & F Aluminium anodised Handle, of extruded section Fabricated Type of size 150mm long complete all as specified and as directed.

S & F Aluminium anodised Handle, of extruded section Fabricated Type of size 100mm long complete all as specified and as directed.

S & F 100 mm size, medium weight Butt Hinges, cold rolled, mild steel including fixtures complete all as specified and as directed.

S & F 75 mm size, medium weight Butt Hinges, cold rolled, mild steel including fixtures complete all as specified and as directed.

S & F Aluminium alloy anodised Sliding Door Bolt with hasp and staple [Bolt Type] of size 300 mm and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S & F Mild Steel work conforming to Fe - 290, Grade E-165 as in Bands, Straps, Supports or Stays for Rainwater, Ventilating Pipes, including Bolts, if required, Hooks [Stay], heavy, for Large Gates, Hook and Pintle Hinges, large Hasps and Staples, Chains, hand made Sliding Bolts, Clamps, Hold Fasts, Wall Ties, Hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters, knee piece inserts, two way and three way straps, plate washers and similar small articles complete all as specified and as directed.

M & L for PCC 1:3:6, Type B-0, using 12.5 mm graded stone aggregate as in hold fast, door and windows frames, any size, single or double rebated,including arrangement for fixing of hinges and fixtures as required complete all as specified and directed.

S & F in repairs Stainless steel wire cloth / mesh with average aperture not exceeding 1.40 mm and dia of wire 0.36 mm and fixed with tinned tacks or Aluminium wire staples with new wooden beading including necessary painting to beading to match with existing surfaces complete all as specified and as directed.

Dismantling Plywood cup board shutters including shelves complete all as specified and as directed.

M & L 19mm thick, Prelaminated Particle Board, One Side Decorative Choice Lamination and other side Balancing White, Medium Density, Interior Grade complete all as specified and as directed.

S & F 18mm thick Plywood, Grade BWR, Type BB, fixed with nails to Wooden Frames complete all as specified and as directed.

S & F 0.9 mm thick Decorative Laminate, Type - 1 of Surface Finish, Colour and Pattern as approved, fixed with approved adhesive as per manufacturer's instructions, complete all as specified and directed.

S & F Second class hard wood small fittings such as brackets of any type, shaped door and window stops and the like including all necessary Labour, articles not exceeding 200 Cu.cm each complete all as specified and as directed.

M & L for two coats of synthetic enamel paint over one coat of pink primer to newly untreated wooden surfaces over 10cm width or girth including preparation of surfaces complete all as specified and as directed.

Demolition of Unreinforced Cement Concrete in ground floors and Pavings not exceeding 15cm thick [below or above ground level] and removing rubbish to a distance exceeding 1.50 KM but not exceeding 5.00 KM complete all as specified and as directed.

M & L for 75mm thick PCC 1:3:6, Type C-1, using 20mm graded aggregate as in Plinth protection etc surface finished even and smooth with out using extra cement and providing 12mm thick joints for full depth of PCC at every 3.00 m and every change of direction duly filled with mastic filling comprising of 01 Part of heated bitumen blown grade of any penetration and 3 parts of sand [all by weight] complete all as specified and as directed.

Demolition of Unreinforced Cement Concrete of any description and in any position not otherwise specifically provided for and removing rubbish to a distance exceeding 1.5 KM but not exceeding 5 KM complete all as specified and as directed.

M & L for rendering to brick / concrete surfaces, 15 mm thick in Cement Mortar 1:3, including mixing water proofing compound as per manufacturers instructions and finishing the top surface even and smooth without using extra cement complete all as specified and as directed. Note: The quoted rate shall be deemed to include cost of water proofing compound and nothing shall be paid extra on this account.

M & L for applying Chemical Injection Treatment in the form of Pressure Grouting by drilling 20 mm dia holes, 60 mm deep @ 100 cm grid at bottom floor and all the internal wall surfaces of the sunken slabs of toilet by injecting Cement Slurry mixed with Grout Admixture "CONBEXTRA EP 10" of M/s. Fosroc Chemicals India [P] Ltd. or its equivalent in M/s. Sika India Pvt. Ltd. or M/s. STP Ltd. or M/s. Choksey Chemicals Pvt. Ltd. or M/s Batik India Pvt. Ltd. at 225 Grams for 50 KG of cement and applying a coat of Brush Bond RFX of M/s. Fosroc Chemicals or equivalent approved water proofing coating as per manufacturer's instructions complete all as required and as directed at site.

M & L for PCC 1:5:10, Type E-2, using 40mm graded stone aggregate as in foundations and mass concrete etc complete all as specified and as directed.

M & L for 40 mm thick, PCC 1:2:4, Type B-0, using 12.5mm graded aggregate with mixed with WPC at 2% by weight as in Sub base for flooring complete all as specified and as directed. Note: The quoted rate shall be deemed to include cost of water proofing compound and nothing shall be paid extra on this account.

M & L for 25 mm thick PCC 1:2:4, Type B-0, using 12.5mm graded aggregate as in levelling course / sub base for flooring, complete all as specified and as directed.

M & L for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc and brushing neat cement slurry with 3.0 KG of cement per Sq.m area, rendering 10mm thick in cement mortar 1:3 on concrete surfaces finished even and smooth without using extra cement including mixing of water proofing compound of approved make @3% by weight of cement for levelling the surface smooth to receive the water proofing membrane, applying a coat of Blown Bitumen of grade 85/25 @ 1.2 Kg per Sq.m, laying Polymeric water proofing membrane of weight not less than 3.00 Kg per Sq.m reinforced with polyester non-woven fabric of weight not less than 150 Grams per Sq.m, by torch application with side over lap of 100mm & end over lap of 150mm & tucked into the chases on vertical surfaces by thermo fusion including applying a coat of Blown Bitumen of grade 85/25 @ 1.2 Kg per Sq.m including taking down existing Roof Treatment of any description and removing rubbish to a distance exceeding 1.50 KM but not exceeding 5.00 KM complete all as specified and as directed. Note: Water proofing compound will be measured and paid separately.

M&L for providing roof cooling ceramic tiles of size 300 x 300 mm, 7 to 8 mm thick, conforming to IS 15622, set and jointed in cement slurry and pointed flush with epoxy mortar to match the shade of the tile including screed bed or bedding layer of mortar 15 mm thick in Cement Mortar 1:3 complete all as specified and as directed. Note: [a] The colour/ shade/ design of tiles shall be as approved by GE.

Demolition of Unreinforced Cement Concrete in ground floors and Pavings not exceeding 15cm thick [below or above ground level] and removing rubbish to a distance not exceeding 100M complete all as specified and as directed.

M & L for 100 mm thick, PCC 1:2:4, Type B-2, using 40mm graded stone aggregate as in Hardstanding / Path flooring etc. as required, surface finished even and smooth complete all as specified and as directed.

M & L for Forming Contraction Joint [Dummy], 30mm deep X 10mm wide, filled with sealing compound and sealed with Sealing Compound Grade "A" for 100mm thick flooring complete all as specified and directed.

M & L for One coat of synthetic enamel paint on old painted wooden surfaces of any description not other wise described over 10 cm width or girth incuding necessary preparation of surfaces complete all as specified and directed.

M & L for One coats of synthetic enamel paint on old painted steel surfaces of any description not other wise described over 10 cm width or girth incuding necessary preparation of surfaces complete all as specified and directed.

M & L for Complete removal of existing treatment of any description on wall surfaces by using vaccume based sanding machine, removal of nails and applying suitable thickness of Cement based Wall Care Putty on walls by using multipurpose mixture for proper mixing of putty and putty sprayer for application of putty including rubbing with sand paper to obtain a smooth surface and making good any undulations on the surfaces and applying two coats of Acrylic Washable Distemper by using auto roller/ airless sprayer over one of alkali resistant primer on wall surfaces complete all as specified and as directed. Note:- The contractor shall carryout Distempering & allied works under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Distempering & allied works through their authorised applicators before commencement of the work to GE for approval.

M & L for One coat of Acrylic Washable Distemper over suitable thickness of cement based wall care putty by using auto roller/ airless sprayer on old decorated surfaces of walls, pillasters, cornices, etc., including necessary preparation of surfaces by using vaccume based sanding machine complete all as specified and as directed. Note:- The contractor shall carryout Distempering under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Distempering through their authorised applicators before commencement of the work to GE for approval.

M & L for Preparation of surface of CI Pipes of 100mm dia and applying one coat of Epoxy painting complete all as specified and as directed.

M & L for One coat of Weather Proof Exterior Emulsion Paint [100% Acrylic] by using auto roller/ airless sprayer on old painted Walls/ ceilings, pillasters, bands, borders, soffits of chajjas and projections including necessary preparation of surfaces by using vaccume based sanding machine complete all as specified and as directed. Notes:- (a) The contractor shall carryout Weather proof Exterior Emulsion Painting under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Weather proof Exterior Emulsion Painting through their authorised applicators before commencement of the work to GE for approval.

M & L for two coats of Weather Proof Exterior Emulsion Paint [100% Acrylic] by using auto roller/ airless sprayer on old painted Walls/ ceilings, pillasters, bands, borders, soffits of chajjas and projections including necessary preparation of surfaces by using vaccume based sanding machine complete all as specified and as directed. Notes:- (a) The contractor shall carryout Weather proof Exterior Emulsion Painting under subject work through the Authorised Applicator of the manufacturer only. The lowest bidder shall submit MoU from manufacturer to provide technical support and trained persons for carrying out Weather proof Exterior Emulsion Painting through their authorised applicators before commencement of the work to GE for approval.

M & L for Repainting G.I. pipes and fittings with a coat of synthetic enamel white paint of approved quality 20mm to 50mm bore complete all as specified and as directed.

Cleaning the existing vertical plastered surface with brush and removing of loose flakes, dirt and foriegn material with high pressure water wash. Filling the cracks with Acriseal or Crackfill of Perma or equivalent, then applying on vertical surface one coat of primer made of Multiprime of Perma or equivalent @ 0.10 liter / sqm and surface shall allowed to dry for 8 to 10 hours. Finally apply two coats of Wall Guard of Perma or equivalent, first coat @ 0.15 liter /sqm and shall allowed to dry for 12 to 24 hours of application and 2nd coat @ 0.10 liter / sqm over dry surface to a thickness of 300 to 500 DFT. complete as per direction of Engineer in charge including surface preparation excluding scaffolding. Note: No further work shall be carried out over the coated area within 72 hours of final coat complete all as specified and as directed.

M & L for One coat of white wash on old decorated surfaces of wall including necessary preparation by brooming down or steel wire brushing complete all as specified and as directed.

M & L for One coat of white wash on old decorated surfaces of ceiling including necessary preparation by brooming down or steel wire brushing complete all as specified and as directed.

M & L for removing Plants with roots by chipping Walls / Beams / Junctions of Vertical Stacks / Water Supply lines or at any other location as directed, applying recommended chemical to prevent growth or plants and making good the disturbed portion with Cement Mortar 1:3 or with PCC 1:2:4, Type B0 [using 12.5 mm graded aggregate] and painting the surfaces to match with existing treatment / finishes and removing debris to a distance not exceeding 1.50 KM complete all as directed.

S & F in repairs Gun Metal Globe or Gate Valve of Class - I, Pressure Tested of 1.5 Mpa, 15 mm bore with iron wheel head, screwed both ends for iron pipe, conforming to IS, ISI Marked complete all specified and as directed.

S & F in repairs Gun Metal Globe or Gate Valve of Class - I, Pressure Tested of 1.5 Mpa, 25 mm bore with iron wheel head, screwed both ends for iron pipe, conforming to IS, ISI Marked complete all specified and as directed.

S & F in repairs Gun Metal Globe or Gate Valve of Class - I, Pressure Tested of 1.5 Mpa, 40 mm bore with iron wheel head, screwed both ends for iron pipe, conforming to IS, ISI Marked complete all specified and as directed.

S & F in repairs Gun Metal Globe or Gate Valve of Class - I, Pressure Tested of 1.5 Mpa, 50 mm bore with iron wheel head, screwed both ends for iron pipe, conforming to IS, ISI Marked complete all specified and as directed.

S & F in repairs Gun Metal Globe or Gate Valve of Class - I, Pressure Tested of 1.5 Mpa, 80 mm bore with iron wheel head, screwed both ends for iron pipe, conforming to IS, ISI Marked complete all specified and as directed.

M&L for Disconnecting existing upto 250 Ltr capacity water tanks and Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, and mention the cleaning date with white paint etc.complete all specified and as directed.

M & L for Cleaning and removing all scale and dirt, etc, from tanks of capacity exc 5000 ltr but not exc 25000 ltr and from mouths of circulating pipes, and mention the cleaning date with white paint etc.etc.complete all specified and as directed.

S & F PVC Lid for 250/500 ltrs water tank complete all specified and as directed.

S&F in repairs 32 / 40mm dia PVC waste pipe fixed to Wash Hand Basin / Kitchen Sinks complete all specified and as directed.

S & F Rectangular Polythene [HDPE] Water Tanks, Loft Type 225 Litres Capacity hoisted and fixed in position including provision of 25mm/25mm dia spouts for connecting inlet, outlet, over flow and washout pipes complete complete all as specified and as directed.

S & F in repairs 15 mm dia Brass ball Valves, high pressure, with polythene float and fly nut complete, screwed for Iron pipe or brass ferrule including taking down the existing valve.complete all as specified and as directed.

S & F in repairs 40 mm dia Brass ball Valves, high pressure, with polythene float and fly nut complete, screwed for Iron pipe or brass ferrule including taking down the existing valve.complete all as specified and as directed.

S & F in repairs 50 mm dia Brass ball Valves, high pressure, with polythene float and fly nut complete, screwed for Iron pipe or brass ferrule including taking down the existing valve.complete all as specified and as directed.

S & F in repairs Stainless steel kitchen sink, made of stainless steel 1 mm thick, with plugs, washers and Waste Fittings, 32 mm dia, Brass, Chromium plated, and 32mm dia PVC flexible Waste Pipe, 750 mm long including bedding in cement mortar on to dwarf wall or including fixing cantilever CI Brackets and connecting union to pipe, overall size 495mm X 420mm, bowl size 410mm X 330mm X 160mm complete all as specified and as directed.

S&F in repairs Helical door spring 300mm, ordinary rat tail rod patttern springs includding roller and roller plate complete all as specified and as directed.

S & F in repairs Bib Taps, 15 mm dia, Brass Chromium Plated, Fancy Type with crutch or butterfly handle, screwed down for iron pipe and fixed etc. complete all as specified and as directed.

S & F in repairs Pillar Taps, cast copper alloy, Chromium Plated, Fancy Type, 15 mm dia, with capstan head, screwed down high pressure with or with out lettered "Hot" or "Cold" with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified.

S & F in repairs Stop Valves, 15 mm bore dia of pipe, cast copper alloy, Chromium Plated, Fancy Type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions etc complete all as specified and as directed.

S & F in repars Stop Valves, 15 mm dia, cast copper alloy with capstan head, Chromium Plated, Fancy Type, screwed down high pressure with crutch or butterfly handle with long shank and cup [concealed type] for iron pipe etc complete all as specified and as directed.

S & F in repairs Angle cocks, 15 mm bore dia of pipe, cast copper alloy, Chromium Plated, Fancy Type, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions etc complete all as specified and as directed.

S & F in repairs Health faucet Brass chromium plated, with 1m flexible pipe fixed fo 15 mm bore iron pipe fixed complete all as specified and as directed.

S&F 10 liters capacity PVC flushing cistern low level with all accessories in repairs including taking down old flushing cistern.complete all as specified and as directed.

S&F in repairs PVC syphon kit (any type / any pattern ) suitable for 10 ltrs capacity 'Slimline' low level flushing cistern and make functional complete all as specified and directed.

S & F in repair, plastic water closet seat cover, black or white or coloured, with ms chromium plated hinging device complete all as specified and directed.

S&F in repair PVC connection 15 mm size with brass CP nut of length 450 mm complete all as specified and directed.

S&F in repair stainless steel grating with doom 100 mm dia without waste hole or with waste hole ( to insert waste pipe from WHB SINK etc).complete all as specified and directed.

S & F in repairs, Brass Chromium Plated Shower Rose of size 125mm with or with out swivel joints fixing to steel pipes complete all as specified and as directed.

Replacement of damaged float handle with new float handle for low level flush tank complete all as specified and as directed. (Make : Super flow or equivalent)

S & F in repairs brass spindles suitable for bib taps/stop cocks of any dia, fixed .complete all as specified and as directed.

S&F in repair bib tap standard of PTMT any color high pressure served for Iron pipe and fixed 15 mm dia (min 90 grams) complete all as specified and as directed. (Make : PRAYAG or equivallent approved make).

S & F in repairs Stainless steel kitchen sink with draining board, made of stainless steel sheet of 1 mm thick, with plugs, washers, Waste Fittings, 32 mm dia, Brass, Chromium plated, and 32mm dia PVC flexible Waste Pipe, 750 mm long, including bedding in Cement Mortar to dwarf wall or including fixing cantilever CI Brackets and connecting union to waste pipe, over all size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and as directed.

S & F in repairs chromium plated cast copper alloy mixer valve for hot and cold water connections with an arrangement for shower and one tap of model No. 6770 : M of JAIL make manufactured by Jupiter Aqualines Pvt Limited, Chandigarh or equivalent as approved by the Engineer-in-charge complete all as specified and as directed

S&F in repairs GI Tank Nipple 15 mm dia of any length.complete all as specified and as directed

Removing kitchen drainage block from the waste pipes by removing grating removing waste material from traps bends etc carefully and Roding with flexible GI wire to clear blocking including disposing the waste material as directed by Engineer -in-Charge

Removing blockages from soil pipes or from WCs by carefully Roding soil pipe with split bamboos or flexible GI wire etc including cleaning the toilet by flushing water and disposing any removed soiled material in each quarter as directed by Engineer -in-charge

S&F in repairs Stainless steel soap stand in bathroom and fixed to walls with necessary screws etc.complete all as specified and as directed

S&F in repairs glass shelves with SS railing in bathroom and fixed to walls with necessary screws etc.complete all as specified and as directed.

Taking down wash hand basin or sink of any size including refixing with MS angle new brackets/ rod bolts in the same places complete all as specified and as directed.

M & L filling of cement moratar in sides of nahani trap, gully trap, rain water pipes outlet etc CM 1:3 by including WPC and making good finishes to arrest leakage/seepage complete all as specified and as directed.

Taking down unserviceable plate rack and S&F stainless steel plate rack size 600mmX750X220mm of approved pattern made out of stainless steel sheet 18 gauge sheet thick with round 8mm dia rods complete all as specified and as directed.

S & F in repair including making good disturbed floor surfaces for vitreous china white semi-pedestal pattern (Anglo-Indian type) water closet with P or S trap complete all as specified and as directed.

S & F in repairs Vitreous China Wash Down Water Closet [Pedestal pattern], White, , PVC Connection of 15mm Bore and 600mm long with PTMT check nut and union etc. including brackets and connections to pipe and flush pipe including plastic water closet seat back closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device and 'P' or 'S' trap complete all as specified and as directed.

S & F in repairs Vitreous China Squatting Pan "Orissa Pattern", White of size 580 mm X 440 mm with integral foot rests and 'P' or 'S' Trap including provision of lime concrete bedding and 10 Litres capacity, PVC Valve less, , PVC Connection of 40mm Bore and 750mm long with PTMT check nut and union etc. including brackets and connections to pipe complete all as specified and as directed.

S & in repairs Vitreous China Ware Wash Hand Basin, White, Flat Back of size 550 mm X 400 mm including brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting strand, 32mm bore PVC flexible waste pipe, PVC Connection of PTMT complete all as specified and as directed.

S & in repairs Vitreous China Ware Wash Hand Basin, White, Flat Back of size 450 mm X 300 mm including brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting strand, 32mm bore PVC flexible waste pipe, PVC Connection of PTMT complete all as specified and as directed.

S & F low density polyethylene pipes (LDPE) 40 mm in small length to facilitate for carry over the waste to nahani trap point etc and fixed as required complete all as specified and as directed.

S & F PVC bends 40mm dia complete all as specified and as directed.

Hacking out old broken glass (any thickness size quality or description) from wooden or metal frames glazed with petty or fixed with beads complete all as specified and as directed.

S&F Sheet glass 4 mm thick ordinary quality and glazing with wooden or aluminium windows in square n.exc 0.5 sqm in each pane complete all as specified and as directed.

S & F 4 mm thick Sheet glass, ordinary quality fixed to aluminium windows in squares exceeding 0.5 Sq. M in each pane complete all as specified and as directed.

S&F in repair Mortice lock vertical type or cylindrical type size 100 mm brass body 4 lever complete all as specified and as directed.

S & F in repairs stainless steel wire mesh with aperture n exc 1.40 mm dia and of of wire 0.36 mm and fixed with existing/new wooden/ aluminium/UPVC beading stapples including painting to beading etc complete all as specified and as directed.

S & F in repairs Aluminium anodised barrel Tower Bolt of size 150 mm size of extruded section complete all as specified and as directed.

S & F in repairs Aluminium anodised barrel Tower Bolt of size 100 mm size of extruded section complete all as specified and as directed.

S & F in repairs Aluminium alloy anodised Sliding Door Bolt with hasp and staple [Bolt Type] of size 300 mm and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

S & F in repairs Aluminium anodised Handle, of extruded section Fabricated Type of size 150mm long complete all as specified and as directed.

S & F in repairs Aluminium anodised Handle, of extruded section Fabricated Type of size 100mm long complete all as specified and as directed.

S & F in repairs 100 mm size, medium weight Butt Hinges, cold rolled, mild steel including fixtures complete all as specified and as directed.

S & F in repairs 75 mm size, medium weight Butt Hinges, cold rolled, mild steel including fixtures complete all as specified and as directed.

S&F in repairs Helical door spring 300mm, ordinary rat tail rod patttern springs includding roller and roller platecomplete all as specified and as directed.

S & F in repairs Floor Door Stopper of size 150 mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring complete all as specified and as directed.

S & F in repairs 20mm bore aluminium alloy anodized curtain rails with brackets complete all as specified and as directed.

S & F in repairs 20 mm dia stainless steel fancy curtain rod having minimum 1mm thick alongwith one pair fancy bracket for each opening/door/window. complete all as specified and as directed. Note:-(Rod and bracket as required at site or as directed by Engr-in-Charge)

S & F in repairs Continuous [Piano] Hinges, Mild Steel, Bright finish or Electrogalvanised and width of Flaps 30mm [When Open] complete all as specified and as directed.

Note for Serial Item No. 1 to 195 : The work shall be carried out up to Ten (16) Storey and the rates quoted are deemed to be including providing double scaffolding and safety measures as required and removal of the same on completion complete all as specified and as directed. Nothing shall be paid extra on this account.

GAGANSRI INFRA (BID ID -3457350)

k.b.venkatarao and co (BID ID -3457664)

VENKATA SAI SRINIVASA CONSTRUCTIONS PRIVATE LIMITED (BID ID -3457528)

SOUTHERN BUILDERS (BID ID -3457670)

srisampathassociates (BID ID -3456902)

M/s.DSRK CONSTRUCTIONS (BID ID -3457343)

Sri Surya Enterprises (BID ID -3456942)