Building Repairing And Renovation Work of Diffirent Muni. Building At Bopal-Ghuma area and Diff. places of Thaltej Ward In North West Zone. (A.R.C.)

Name of Work:- Building Repairing And Renovation Work of Diffirent Muni. Building At Bopal-Ghuma area and Diff. places of Thaltej Ward In North

West Zone. (A.R.C.)

Sr.No Oty. Item Description Rate Unit Amt.Rs.

Excavation for foundation up to1.5 m depth including sorting out and stacking of

useful materials and disposing of theexcavated stuff upto 50 Meter lead.(A)

Loose or soft soil (R & B S.O.R 2023-24 I.no. Item Code 04001A)

40 Upto 1.5 mt Depth 115.92 Cmt

10 1.5 to 3.0 mt.depth 128.52 Cmt

Filling available excavated earth (excluding rock) in trenches, plinth, sides of

2 41 foundations etc. in layers not exceeding 20 cm. in depth consolidation each 129.10 Cmt

deposited layer by ramming and watering.

Providing and laying cement concrete1:5:10 (1-Cement: 5- coarses

sand and:10-hand broken stone aggregates 40mm nominal size) and

curing complete excluding cost of formworkin (A) Foundation and Plinth.

Providing and laying cement concrete1:4:8 (1-Cement: 4- coarses

4 7 and:8 hand broken stoneaggregates 40mm nominal size) and curing complete 2653.67 Cmt

excluding cost of formworkin (A) Foundation and Plinth

Providing and laying cement concrete1:3:6 (1-Cement: 3- coarses

sand and:6-hand broken stone aggregates 40mm nominal size) and curing

complete excluding cost of formworkin (A) Foundation and Plinth.

Providing and laying cement concrete 1:3:6 (1-Cement:3-coarse sand:6-

6 7 crushed stone aggregates 20mm nominal size) and curing complete 4006.15 Cmt

including cost of formwork in (A) wall caps/coping

Providing and laying cement concrete work 1:2:4 ((1-Cement:2- coarse

7 sand:4-graded aggregates 20mm nominal size) curing complete

excluding cost of formwork and reinforcement.

a 10 Foundations, footings, base or columns and mass concrete 3923.53 Cmt

Slabs, landing, shelves, balconies, lintels, beams, girders and cantilivers

upto floor two level

c 5 Independent piers, columns, and pillars, upto floor two level 3661.30 Cmt

Provdg. & laying cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded

stone aggregates 20 mm nominal size) for reinforced concrete chhajjas

not exceeding 10 cm. thickness upto floors two level including finishing

the exposed surfaces with cement mortar 1:3 (1 cement : 3 find sand) to give

a smooth and even surface centering and form work and curing complete

excluding cost of reinforcement.

Providing and laying controlled cement concrete / Ready Mix Concrete of

9 M-200 and curing complete, excluding the cost of form work and

reinforcement for reinforced concrete work in:

(A) 5 Foundations, footings, base of columns, and mass concrete. 3977.88 Cu.M.

(B) 7 Walls from top of foundations /level up to floor Two level. 4484.17 Cu.M.

Slabs,landing,shelves,Balconies Lintels, Beams, Girders and Cantilever upto floor

(D) 5 Columns, pillars, posts, and struts, up to floor two level. 4558.20 Cu.M.

(E) 5 Staircase up to floor two level. (excluding landing) 5418.91 Cu.M.

(K) 8 Vertical and horizontal fins up to floor two level. 4701.97 Cu.M.

Providing and Laying ordinary cement concrete 1:2:4 (1-Cement 2-

coarsesand: 4-graded stone aggregates 20 mm nominal size) and finishing

smooth with curing etc. complete including the cost of form work but excluding the

10 1 cost of reinforsement for R.C.C work in (iv) Slabs having more than 13 cm and 6241.78 Cum

upto 15 cm.thickness

Providing and Laying ordinary cement concrete 1:2:4 (1-Cement 2-

coarsesand: 4-graded stone aggregates 20 mm nominal size) and finishing

smooth with curing etc. complete including the cost of form work but excluding the

cost of reinforsement for R.C.C work in (iv) Slabs having more than 8 cm and

upto 10 cm.thickness

Brick work using common burnt clay building bricks having crushing

12 strength not less than 35kg./Sq.Cm.in foundation and plinth in Cement

Mortar1:6 (1-Cement :6 - fine sand)

15 (A) Conventional (upto 10 ton) 3981.21 Cmt

12 B) Modular 4241.70 Cmt

Extra Rate for brickwork in Above Item for super structure above plinth

level upto floor two level (B) Conventional

a 5 (A) Conventional 272.25 Cmt

b 5 B) Modular 262.35 Cmt

C) above floor two level Item No. 2(6.13) (A) Modular Per Floor

D) above floor two level Item No. 2(6.13) (B) Conventional Per Floor

Providing and laying in position Ready Mixed M250 grade concrete for reinforced

cement conctere work , using cement content as per approved Design Mix

manufactured in fully automatic batching plant and transported to site of work in

transit mixer for a lead up to 10 kms having continuous agitated mixer,

manufactured as per mix design of specified grade for reinforced cement concrete

work including pumping of R.M.C. from transit mixer to site of laying, excluding the

cost of centering shuttering finishing and reinforcement including cost of admixtures

13a 10 in recommended proportions as per IS: 9103 to accelerate/ retard setting of 4853.56 Cmt

concrete, improve workability without impairing strength and durability as per

direction of the Engineer - in - charge. Without Fly Ash (Min cement level as per

latest IS 456 shall be maintained) (Cement level 450 kg )

Half brick masonry in common brunt clay building bricks having crushing

strength not less than 35 Kg/Sq.Cm. in Cement mortar 1:5 ( 1-Cement : 5 coarse

sand ) in foundation and Plinth conventional brickwork

Extra for half brick masonry in super structure above plinth level upto

floor two level (B) conventional

Providing form work in ordinary timber planking so as to give a rough

finish including centering, shuttering, strutting and propping etc. height of

16 propping and centering below supporting floor to celling not exceeding 4 M

& removal of the same for in situ reinforced or plain concrete work upto floor

a 40 Foundation, footings, bases of columns etc. and mass concrete. 171.68 Smt

(B) Flat surfaces such as soffits of supspened floors slabs Landings and the like. (1)

Floors etc. upto 200 mm in thickness.

(B) Flat surfaces such as soffits of suspended floor roof slabs Landings and the like.

(2) Floors etc. above 200mm in thickness.

Vertical surface such as walls (any thickness) partitions and the like including

attached buttresses & string course & the like.

(ii) Sides And Soffits Of Beam, Haunchings Cantilevers, Girders,

Bressumers And Lintels Not Exceeding 1 M In Depth.

f 40 (G) Columns PillarsPosts and struts. (1) Square Rectangular Polygonal in plan. 297.68 Smt

g 40 (2) Circular or curved in plan. 422.10 Smt

(H) (2) Sides and soffits of Beams Beam Haunchings canti-levers Girders

Bressumers and Lintels exceeding 1M.in Depth.

Providing and fixing 35 mm thick panelled, glazed or panelled and glazed

shutters for Doors windows and clear story windows including anodised

alluminium But hinges with necessary screws and indian teak wood shutters

a 3 (A) Plywood sheet panels. 3459.09 Smt

b 3 (B) Particle board panels 3464.51 Smt

c 2 (C)Hard board panels. 3433.65 Smt

d 2 (D) Asbestos sheet panels. 3406.53 Smt

Providing and fixing 25 mm thick shutters for cup boards etc. including

18 2 black enamelled M.S. butt hinges with necessary screws.(A) Indian teak 3006.75 Smt

wood. (i) Fully Panelled.

Providing and fixing 25 mm thick shutters for cupboards etc. including anodised

a 2 alluminiu butt hinges with necessary screws. (A) Indian teak wood. (ii) Fully Glazed. 3006.75 Smt

Providing and fixing 25 mm thick shutters for cupboards etc. including anodised

b 3 alluminiu butt hinges with necessary screws. (A) Indian teak wood. (ii) Partly 2814.42 Smt

panelled and partl glazed.

Providing and fixing M.S. grills of required pattern to wooden frames of windows

etc. with M.S. flats at required spacings and frame alround, square or

round bars with round headed bolts and nuts or by screws (A) Plain Grill.

Providing and fixing glazed louvered glass windows and ventilators

20 3 with teak wood frame 10 cm. x 7 cm. size including 3 coats of oil painting to 4102.54 Smt

wood work etc.complete.

Providing and fixing glazed louvered glass windows and ventilators

with teak wood frame 10 cm.x7 cm. size including 3 coats of oil painting

to wood work etc.complete.with wooden louvers plank 12mm thick

Providing and fixing 35 mm thick shutters for Doors, windows and clere

story windows including Indian teak wood frames 10 cm x 7 cm. size

22 6 including anodized alluminium fixtures and fastenings including primer coat of 4595.06 Smt

approved quality and two coats of oil painting etc, complete.(ii) Fully Glazed.

Providing and fixing 35 mm thick shutters for Doors, windows and clere

story windows including Indian teak wood frames 10 cm x 7 cm. size including

23 3 black enamelled iron oxidixed fixtures and fastenings including primer 5285.45 Smt

coat of approved quality and two coats of oil painting etc, complete.(ii) Fully

Providing and fixing 35 mm thick shutters for Doors, windows and clerestory

windows including Indian teak wood frames 10 cm x 7 cm. size including anodized

alluminium fixtures and fastenings including primer coat of approved quality and two

coats of oil painting etc, complete. (iii) Partly panelled and partly glazed.

Providing and fixing 30 mm thick FACTORY MADE SOLID PANEL PVC

DOOR SHUTTER consisting of frame made out of M.S.tubes of 19 gauge

thickness and size of 19 mm x 19 mm for stiles and 15 mm x 15 mm for top and

bottom rails.M.S. frames hall have a coat of steel primers of approved make

and manufacture, M.S. frames hall be covered with 5 mm thick heat moulded

PVC ‘C’ channel of size 30 x 50 mm formings tiles, and 5 mm thick 75 mm

24 5 wide PVC sheets for to prail, lock rail and bottom rail on either side, and 10 mm (5 1135.02 Smt

mm x 2) thick, 20 mm wide cross PVC sheet as gap insert for top rail and

bottom rail, Panelling of 5 stiles and rails with 30 mm wide x 5 mm thick PVC

sheet beading on eighter side, and joined together with solventcement

adhesive,. An additional 5 mm thick PVC strip of 20 mm width is to be stculkon the

interiors side of the ‘c’ channel using PVC solvent cement adhesive

etc. complete as per direction of Engineer incharge, manufacture’s

specification and drawing.

Providing and fixing in position collapsible steel shutters with vertical

channels 20 x 10 x 2 mm braced with flat iron diagonal 20 x 5 mm size with

25 4 top and bottom rails T iron 40 x 40 x 6 mm with 38 mm dia steel pulleys complete 5391.23 Sq.M.

with bolts, nuts, locking arrangements, stoppers, handles, including a

priming coat of red lead paint & approved make.

Providing and fixing 1 mm thick M.S. sheet sliding shutters with frame and

diagonal braces of 40x40x6 mm angle iron, 3.15 mm M.S.gusset plates at

Junctions and corners 25 mm dia. pulley, 40x40x6 mm angle and T-

iron guide rail at top and bottom respactively with handles, stoppers and

locking agangement etc, including applying a priming coat of red lead paint.

Providing & Fixing in position Alluminium doors with frame using approved

quality anodised extruded alluminium section as approved by Engg.in

charge(Jindal alluminium) (a) Frame sections 101.6x44.45 mm (b) Shutter

bottom vertical & top section 83.5x44.45 (wt.1.31 kg/mt.)(at 1.31 kg/mt) (c)

27 5 Shutter bottom section at 114.3x44.45 mm at (1.37kg/mt) Shutter middle 2900.00 Smt

section at 100x44.3 wt.(1.37 kg/mt) incl.providing & installing 5 mm thick

approved color Acrylic sheet of standard quality fixed with glazing chips on

upper pannel & Laminated sheet on lower pannel (wtt.0.13 kg/Rmt)

etc.comp.as direction of engg.in charge.(N.S.)

Providing and fixing extruded aluminum window having extruded aluminum Colour r

Powder Coated section frame main outer size 127mm x 38.10mm x 1.35mm ,@

Wt.1.384 Kg/mt,horizontal Four track member size 122.20mm x 31.75mm x

1.10mm @ Wt. 1.205 Kg/mt,vertical member of size 122.20mm x 31.75mm x

28 1 1.50mm ,@ Wt. 1.398 Kg/mt with sliding shutters of horizontal member size 40mm 2119.14 Sq. M.

x 18mm x 1.29mm @ wt.of 0.456Kg/mt,vertical member of size 40mm x 18mm x

1.29mm @ wt.of 0.456Kg/mt,@ with 5 mm thick transparent bronze colour tinted

float glass with powder coated aluminum fittings and fixtures and transparent silicon

sealant glass fixing to frame as per details etc complete for window.

Providing & Fixing in position Alluminium vents with frame using approved

anodised extruded alluminium section as approved by Engg. In

charge.(Jindal alluminium) units equivalent Approved Rate)Frame section of

63.50 x 38.50 mm. (wt. 0.68Kg/Rmt) incl. Providing & Installing 5 mmthick

approved color Acrylic sheet of standard quality etc. comp.

Providing and fixing standared extruded of alluminium section of size

mmx38.10 mmx1.2 mm (Jindal Section:2434, or equivalent @ Wt.0.643 Kg/mt)

with colour anodized alluminium frame for ventilation with 5 mm thick

frosted glass as details etc complete for Ventilation

Providing and fixing standared extruded of alluminium section of size 63.50 x

x 1.95 mm,@ Wt 1.094Kg / Rmt with colour Powder Coated alluminium frame with

5 mm thick transparent bronze colour tinted float glass as details etc complete for

Providing and laying 40 mm thick marble chips flooring rubbed and polished

(I.E.terrazo) to granolithic finish with under layer 30 mm thick cement concrete1:2:4

(1-Cement: 2-coarse sand: 4-graded stone aggregate 10 mm and down

gauge) and to player 10 mm thick with white, black or white and blak marble cihps

32 5 of required sizes from 1 mm to 4 mm nominal size laid in cement marble powder 811.13 Sqm

mix 3:1 (3- Cement:1-Marble powder by weight) in proportion of 4:7 (4-

Cement: 7-marble chips by volume) (C) Medium Shade pigment

with approx 50% white cement and 50% ordinary cement (In top layer only)

Providing and laying marble chips skirting (Terrazo) or dedo rubbed, and

polished to Granolithic finish to player 6 mm white, black or white and black

marble chips of size from smallest to 4 mm nominal size laid in cement

marble powder mix 3:1 (3-Cement: 1 marble powder by weight) in

proportion of 4:7 (4-cement marble powder mix: 7-marble chips by volume) (B) Light

shade pigment with white cement (In top layer only)

Providing and laying white glazed tiles 6mm thick in flooring treads of steps and

34 45 landing laid on a bed of 12mm thick cement mortar 1:3 (1-cement : 3-coarse sand ) 908.17 Sq.M.

finishing with flush

Providing and laying Ceramic tiles 6 mm thick in flooring treads of steps and

35 30 landing laid on a bed of 12 mm thick cement mortar 1:3 (1- cement :3-coarses 960.47 Sq.M.

and) finishing with flush pointing in white cement.

Providing & Fixing 20 mm thick Mirror Polished Decorative Granite Board with

Computerised Golden Letters Discription as per instructions of engg.

in charge to M.S. frame structure for Inaugaration & Public

Handover Function (N.S.)

Providing and laying Vitrified tiles 8 to 10 mm thick, 36''x36'' in flooring treads of

37 20 steps and landing laid on a bed of 12 mm thick cement mortar 1:3 (1- 1469.91 Sq.M.

cement:3-coarses and) finishing with flush pointing inwhite cement.

Providing and laying Vitrified tiles 8 to 10 mm thick, 24''x24'' in skrting risers of steps

38 18 and dedo on 10 mm thick cement plaster 1:3 (1- cement: 3-coarse 1130.15 Sqm

sand) and jointed with white cement slurry

Providing and laying Vitrified tiles 8 to 10 mm thick, in skrting risers of steps and

39 25 dedo on 10 mm thick cement plaster 1:3 (1-cement:3- coarse sand) and 1523.61 Sqm

jointed with white cement slurry

Providing and laying Vitrified tiles 8 to 10 mm thick , 24'' x 24'' in flooring treads of

40 25 steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1- cement : 3- 1062.50 Sq. M.

coarse sand ) finishing with flush pointing in white cement.

Providing and laying 24" x 24" vitrified 8 to 10 mm th.Double Charged

Gloosy / Matt tiles of Approved make as Approved by Adl.C.E. / Consultants

for upto 10 cm high skirting as approved by Engineer in charge over 10 mm

thick cement mortar 1:6 (1 cement : 6 coarse sand)on new surface& jointed with

colour cement slurry incl with flush pointing & cleaning the surface etc. comp.

Providing and laying polished Kota stone slab flooring over 20 mm (Average)

thick base of cement mortar 1:6 (1-cement:6-coarses and) or

42 50 L.M.1.1.5 (1-Lime putty:1.5-coarses and) laid over and jointed with grey 982.83 Sq.M.

cement slurry mixed with pigment to match the shade of slab including

rubbing and polishing etc. complete. (A) 25 mm thick

Providing and laying marble stone slab flooring over 20mm (average)base of

cement mortar 1:6 (1-cement : 6 coarse sand) or L.M. 1:1.5(1- lime putty : 1.5 -

coarse sand) laid and jointed with gray cement slurry including rubbing and

polishing complete. (A) Marble slab 25mm thick

Providing and laying polished Kota stone slab flooring over 20 mm (Average)

thick base of cement mortar 1:6 (1-cement:6-coarses and) or L.M.1.1.5

laid over and jointed with grey cement slurry including rubbing and

polishing etc.complete. (B) 30 mm thick

Providing and laying polished kota stone slab 25 mm thick in risers of steps, skirting

Dedo and pillars laid on 10 mm thick cement mortar 1:3 (1-Cement :3 coarses

and) and jointed with gray cement slury mixed with pigment to match the

shade of slab including rubbing and polishing etc.complete.

Providing and laying cement concrete flooring 1:2:4 (1-cement: 2-coarses

46 5 and:4-graded stone aggregate 20mm nominal size) laid in one layer and 297.68 Sq.M.

finished with a floating coat of neat cement. (A) 40mm thick.

Providing and laying cement concrete flooring 1:2:4 (1-cement: 2-coarse

47 5 sand:4-graded stone aggregate 20mm nominal size) laid in one layer and 348.08 Sq.M.

finished with a floating coat of neat cement. (B) 50mm thick.

Providing and laying broken china mosaic flooring for terrace using 12 mm to

20 mm broken pieces of glazed tiles to be laid over cement mortar 1:3 to plain or

slope and to be tempered to bring mortar creme out upto surface using

white cement including rounding off junctions and extending them up to15

cm along the wall, clearing with water and oxalic acid etc.as directed.

Providing and laying coloured glazed tiles of the size 300 mmx200

mmx8 mm/300 mmx450 mmx8 mm in skirting, risers of steps and dedo on

10 mm. thick cement plaster 1:3 (1cement: 3 coarse sand) & jointed with

white cement slurry.

Providing ridges or hips 600 mm overall in plain G.I. sheet class-3 fixed with

50 1 G.I. J or L Hooks and nuts 8 mm dia G.I. Limpet and bitumen washer 635.58 Sqm

complete. (1) 0.80 mm thick sheet.

Providing and fixing 150 mm wide 450 mm over all semi circular plain G.I.sheet

class-3 gutter with Iron brackets 40 mmx3 mm size Bolts, Nuts, washers etc.

including making necessary connection with rain water pipes. (i) 0.80 mm thick

Providing and fixing five courses water profing treatment with bitumen

felt consisting of second and fourth course of blown/ bitumen or/and

residual bitumen applied hot at 1.2 kg.per Sq.M.of area for each course

52 1 and first course with fibre base bitunen saturated under lay type land third 466.84 Sqm

course with fibre base self finished felt type 2 grade 1 and fifth and final course

of stone grit 6 mm and down size or pea sizes gravel spread at

0.008 Cu.Metre/Sq.metre preparation of surface excluding grading

Providing and fixing on wall face C.I. Rain water pipe including filling the joints

53 1 with spun yarn soaked in neat cement slurry and cement mortar 1:2(1- 283.62 Rmt

Cement : 2-fine sand) (A) 75 mm dia.

Providing 15 mm thick cement plaster in single coat on Rough (Similar)

54 86 side of single or half brick walls for interior plastering up to floor two level and 174.83 Sqm

finished even and smooth in (i) Cement mortar 1:3 (1-cement :3-sand)

Providing 20 mm thick sand faced cement plaster on walls upto height 10 metres

above ground level consisting of 12mm thick backing coat of C.M. 1:3 (1-cement : 3-

sand) and 8mm thick finishing coat of C.M. 1:1 (1-cement : 1-sand) etc. complete.

Colour washing with lime on wall surface (two coats) over and including

a primary coat of white washing to give an even shade after through brooming

the surface to remove all dirt, dust, mortar drops and other foreigh matter.

Removing dry or oil bound distemper by a washing and scraping

57 10 and sand papering the wall surface smooth including necessary repairs to 11.19 Sqm

scratches complete.

Distempering with dry distemper of approved brand and manufacture (two coats)

and of required shade on wall surfaces of given an even shade, over and

58 43 including a priming coat of whiting after thoroughly brooming the 46.94 Sqm

surface free from mortar dropping and other foreign matter.

Distempeing (Two coats) with oil bound distemper of approved brand and

manufacture and of required shade on wall surfaces to give an even shade,

over and including a priming coat with distemper primer of approved

59 55 brand and manufacture after thoroughly brushing the surface free from 76.08 Sqm

mortar dropping and other foreign matter and also including preparing

the surface even and sand papered smooth.

Extra Coat for Above Item over above for every subsequent coat of

approved brand and manufacture.

Wall painting (two coats) with plastic emulsion paint of approved brand and

manufacture on undecorated wall surface to give an even shade including

throughly brushing the surface free from mortar droppings and other foreign

matter and sand papered smooth.

Extra over item for every sub sequent coat of wall painting with plastic

emulsion paint of approved brand

Extra over item for painting with plastic emulsion paint of approved brand on

ceilings and sloping roofs.

Applying priming coat over new steel and other metel surface after and

including preparing the surface by throughly cleaning, oil, grease, dirt

63 50 and other foreign matter and scoured with brushes fine steel wood, scrapers 34.34 Sqm

and sand paper with ready mixed priming paint brushing red lead.

Painting two coats (excluding priming coat) on new steel and other metal

surface with enamel paint, brushing, interior to give an even shade including

cleaning the surface an even shade including cleaning the surface of all dirt, dust

and other foreign matter.

Painting one coats (excluding priming coat) on previously painted steel and

65 55 other metal surface with enamel paint, brushing to give an even shade including 54.35 Sqm

cleaning the surface of all dirt, dust and other foreign matter.

66 25 Extra over item for every sub sequent coat of paint. 50.40 Sqm

Painting two coats (excluding priming coat) on new steel and other metal

67 5 surface with synthetic enamel paint, brushing to give an even shade including 64.66 Sqm

cleaning the surfaceofalldirt,dust and other foreign matter.

Painting one coats (excluding priming coat) on previously printed steel and

other metal surface with synthetic enamel paint, brushing to give an even

shade including cleaning the surface of all dirt, dust and other foreign matter.

69 5 Extra over Above item for every sub sequent coat of paint. 43.47 Sqm

Painting two coats (excluding priming coat) on external surface of new rain

water, soil, waste and vent pipes and fittings with ready mixed bituminous

brushing, black, anti corrosive to give an even shade including cleaning of all

dirt, dustand other foreign matter.(75 mm dia)

Painting two coats (excluding priming coat) on external surface of new rain

water, soil, waste and vent pipes and fittings with ready mixed bituminous

brushing, black, anti corrosive to give an even shade including cleaning of all

dirt, dust and other foreign matter.(100 mm dia)

Painting two coats (excluding priming coat) on new wood and wood based

surface with enamel paint, interior to give an even shade including

72 50 cleaning the surface of all dirt, dust and other foreign matter sand papering 26.78 Sqm

and stopping. (a) Ready mixed paint brushing wood primier pink.

Painting one coats (excluding priming coat) on previously painted wood and

wood based surface with enamel paint, to give an even shade including cleaning

the of all dirt, dust and other foreign matter.(b) Ready mixed paintbrushing priming

74 5 Extra over Above item for every sub sequent coat of paint. 24.26 Sqm

Painting two coats (excluding priming coat) on new wood and wood

based surface with ready mixed paint, brushing, oil, gloss, semi gloss to give

and even shade including cleaning of all dust, dirt and other foreign matters

and papering and stopping.

Finishing wall with weather proof exterior emulsion paint on wall surface

(two coats) to give an required shape even shade after thoroughly brushing

the surface to remove all dirt, and remains of loose powdered

materials.etc complete

Applying two coats of Birla (white cement based) or Asian

(acryliclapy-putty) or equivalent & two coats of primer of approved brand and

77 35 manufacture on new wall surface to give an even shade including thoroughly 40.19 Sqm

brushing the surface free from mortar dropping and other foreign matter and

sand papered smooth.

Painting one coats (excluding priming coat) on previously painted wood and wood

based surface with enamel paint, to give an even shade including

cleaning the of all dirt, dust and other foreign matter.

Writing letter or figures on any surface with black japan paint (stops,

79 50 comas, hyphens and the like not to be measured and paid for separately) 3.15

(i) Block (Letters/Figures) (Per 10 Letter pet CM.HT)

Demolition including stacking of serviceable materilas and disposal of

unserviceable materials with all lead and lift. (i) R.C.C. work

Demolition of Brick work and stone masonry including stacking of serviceable

81 15 materil as and disposalof unserviceable materials with all lead and lift.(ii) In 544.95 Cu.M.

Dismentaling tiled of stone floors laid in mortar including stacking of serviceable

82 20 materil as and disposal of unserviceable materials with all lead and lift. 47.25 Sqm

Dismentaling of sheet roofing including ridges, Hips, Valleys, Gutters etc.

83 1 stacking of serviceable materil as and disposal of unserviceable 47.25 Sqm

materials with all lead and lift.(i) G.I.sheet roofing.

Dismentling steel work including distempering and stacking the materials

with all lead and lift.

Dismentling doors, windows, ventilators etc. (wood or steel) shutters

including chowkhats architraves, hold fasts and other attachment etc.

complete and stacking the material within all lead and lift.(i) Not exceeding

Dismentling doors, windows, ventilators etc. (wood or steel) shutters

including chowkhats architraves,hold fasts and other attachment etc.

complete and stacking the material with in all lead and lift.(ii) Exceeding

Dismentling barbed wire in fencing including making rolls and also including

dismentling fencing posts including all earth work concrete in base and making

87 30 good the disturbed ground stacking useful materials as directed and 66.15 Rmt

disposing as directed and disposing of the unserviceable materials

with all lead and lift.

Dismentling C.I. pipes G.S.W. pipes abd A.C. rain water pipes with fittings

88 30 and clamps including stacking the materials with all lead and lift (for any dia, of 74.03 Rmt

Dismantling santtary fittings like wash basin . W.C. pan Indian and Europe an

89 25 type, flushing tank etc. including stacking the materials with all lead and lift 401.63 Each

Scraping oil paint from steel and other metal surface and making the

surface even (with Hand Scraping.)

Removing and scraping of old deteriorated plaster of any thickness

from wall / R.C.C member including stacking of serviceable material

and disposal of unserviceable from site of work with all lead and lift

Providing and fixing M.S. fan clamps of shape and size as specified

in existing R.C.C. slab including cutting chase and making good.

Cutting out cracks of roof terrace to V-section, cleaning out, wetting, grouting

with cement and sand slurry 1:3 (1-cement 3-sand )

Cutting out cracks roof terrace to V-Section cleaning out and filling solidly

with a hot mixture of bitumen and clean dry sand (1:1 by weight)

Providing & Fixing in position Alluminium doors with frame using approved

quality anodised extruded alluminium section as approved by Engg.in

charge(Jindal alluminium)(a) Frame sections 101.6x44.45 mm (b)

Shutter bottom vertical & top section 83.5x44.45 (wt.1.31 kg/mt.)(at

95 3 kg/mt) (c) Shutter bottom section at 114.3x44.45 mm at (1.37 kg/mt) Shutter 2900.00 Sq. M.

middle section at 100x44.3 wt.(1.37 kg/mt) incl.providing & installing 5 mm

thick approved color Acrylic sheet of standard quality fixed with glazing

chips on upper pannel & Laminated sheet on lower pannel (wtt.0.13 kg/Rmt)

etc.comp.as direction of engg.in charge.(N.S.)

Providing & Fixing in position Fully Panelled / Partly Panelled Partly Glazed /

Fully Glazed Alluminium doors with frame using approved quality anodised

extruded alluminium section as approved by Engg. In charge.(Jindal

alluminium )(a) Frame sections 101.6x44.45 mm b) Shutter vertical & top

96 3 section 83.5x44.45 (wt. 1.31 kg/mt.)( at 1.31 kg/mt) © Shutter bottom 4583.00 Sq.M.

section at 114.3 x44.45mm at ( 1.37 kg/mt ) Shutter middle section at

100x44.3 wt. (1.37 kg/mt ) incl. providing & installing 5 mm thick Glass of

standaed quality fixed / 12 mm thick Laminated sheet with glazing chips

(wt. 0.13 kg/ Rmt) in panels etc. comp. as per Detail Given & direction

of engg.in charge.

Providing & Fixing in position Alluminium window 2/3/4 track sliding /

fix type with frame using approved anodised extruded alluminium section

97 3 as approved by Engg. In charge.(Jindal alluminium) units 4518.00 Sq. M.

equivalent. including P/F installing 5 mm thick clear/tinted Glass of standard

quality etc.comp.

Providing & Fixing in position Alluminium vents with frame using approved

anodised extruded alluminium section as approved by Engg. In

98 4 charge.(Jindal alluminium) units equivalent Frame section of 63.50 x 38.50 mm. 4218.00 Sq. M.

(wt.0.68 Kg/Rmt) incl. Providing & Installing 5 mm thick Glass of

standard quality etc. comp.

Providing and fixing of Ridge flashing for roof panel shall be made

out of 0.5 mm thick pre coated GI sheet. The Pre coatedsheet shall be

of minimum 240 mpa steel grade confirming to IS 14246:1995 and shall

have zinc coating of minimum 120 gsm as per IS:277:1992, 5-7 microns

99 2 epoxy primer on both side of the sheet and polyester top coat 15-18 micron. 510.10 Sqm

The PP GI Sheet shall have plastic protective guard film of minimum

microns to avoid scratches during transportation. The ridge shall be fixed to

the steel members by poprivetor self drilling/self stitching fastners @

maximum 450mm c/c along length of capping/flashing etc complete .

Supplying and fixing vinyl flooring over the surface having 1-2 mm thickness

100 4 as per directed by engineer incharge etc as completed (N.S.) 963.00 Smt

Providing and laying 15mm bamboza wooden flooring as per architect's

drawing with all necessary details as directed by the project

consultants. Use underlay for better result as per Detail specifications and

directed by the project consultants. (N.S.) Approved Rate )

Providing and fixing 1.20 Metre high fencing with 2.0 Metre long M.S. Angle

posts 40 mm x 40 mm x 6 mm and oil painting 3 coats fixed at 2.5 Mt,

C/c. with five Horizontan lines and two diagonals of galvanised steel barbed

wire weighting 9.38 Kg. per 100 Metre, strained and fixed to posts with G.I,

staples including fixing the posts in ground with 0.5 M x 0.5.M x 0.5 M. block

in C.C 1:5:10 etc complete.

Renovation and Repairing work in Chainlink fencing any size and also

103 3 refixing work incl. febrication work with all materails to be painted one 735.00 Rmt.

coat of primer and twocoats of paint as directed inline and level. (N.S.)

Constructing a sink (chowkedi) with C.C. 1:2:4, 12 cm. thick over B.B.

masonry in C.M, (1:6) in front and dwarf wall 1.0 Mt. high and 23 cm. thick

cement plaster to masonry / in C.M.1:3) and cement concrete flooring in 1:2:4:

mix 5cm.dia.drain pipe etc.complete.

Constructing a cooking platform 60 cm. width and 70 cm high resting on B.B.

Masonry walls 23 cm. thick in C.M. (1:6) with (i) Fixing or precast R.C.C.

105 5 1:2:4) 8 cm. thick slab with marble chips set in C.M. (1:6) (6 mm thick 933.98 Rmt

terrazo) with plastering on exposed faces walls in C.M. (1:4) etc complete.

Extra rate for using Ready Mix Concrete of any grade for below ground

level to vertical upto any floor with delivery & suction Pipe & Pump etc. The

rate includes fule, pump operator, skilled labor, driver etc completed and as per

direction of engineer in charge

P/A Tremix with dewartering machine and floater machine on constructed

CC work for finishing the surface as per requirement. The rate including all

machinaries, labor, loading, unloading, transportaion etc complete as

per direction given by engineer incharge.

Carrying out timber treatment to all wood work including drilling holes and spraying

oil based chemical solution on surface of timber work for termite control including

labor and material etc. complete. Using Chlorpyriphos20 EC as per 6313 2013 Part

108 5 III (1% concentration by mass) is recommended one litre chemical emulsion diluted 54.98 Smt

with 19 liters of kerosene. Total diluted concentration will be 20 liters inclusive of

liter chemical emulsion application in drilled holes and 0.75 / Litre chemical per one

Sqmt two coat on wood surface not protected by paint or varnish.

Applying general insecticide pest control treatment to floors, cupboards etc

including labour materials etc. complete. Using Imidacloprid 30.5 SCas Per IS

part -II( (0.075% concentration by mass) is recommended 10.5ml chemical diluted

with 5 liters of water application 0.5 litre chemical /Sqm of surface is recommended

Carring out plinth treatment to post construction / existing structure by spraying

chemical solution for termite control treatment including labour and material

consist ment with I.S. specification. Using Chlordene and Chior purfiles

110 5 20 EC. As Per 6131_paret-II Consentration Weight on percentis 104.90 Smt

recommended i.e one litre 20 EC chemical emulsion with 19 liter give 1%

concrentration inclusive of one litre chemical emulsion appication attherate

of 5 Litre chemical / Sqm of surface is recommended as per I.S

Carrying out wall treatment for termite control including spraying with chemical

solution in oil base including labour and material Using Chlorpyriphos 20 ECAs per

IS 6313 part - II (1% concentration by mass) is recommended i.e one litre chemical

emulsion diluted with 19 liter oil base. Total solution will be 20 liters inclusive of one

liter chemical emulsion application at the rate of 7.5 litre chemical / Sqm of surface

is recommended as per I.S.S

Providing erecting and fixing double coated Syntex or equivalent

112 5 PVC.(ISI) water tank of required capacity each with all necessary fittings and 3.91 Litre

connection etc. complete on terrace.

Providing and fixing to wall, ceiling and floor galvanised Mild steel tubes

113 (Medium grade) of the following nominal bore, tube fitting and clamps

including making good the wall ceiling and floor.

Providing and laying in trenches galvanised mild steel tubes (Midium

114 grade) of the following nominal bore, and tube fitting (Earth work in

trenches to be measured and paid for separately)

Making connection of galvanised Mild steel distribution branch with galvanised

mild steel main 50 mm to 80 mm nominal bore by providing and fixing

tee including cutting and threading the pipes complete.

Providing and fixing to wall ceiling and floor 6.0 Kg.F/Cm2 working pressure

poluthene pipes of the following out side Dia. Low densidy, complete

with special falnge compression type fittings,wall clips etc.including

making good the wall ceiling and floor.

Providing and fixing to wall ceiling and floor 10.0Kg.F/Cm2 working pressure

polythene pipes of the following out side Dia. Low densidy, complete

with special falnge compression type fittings, wall clips etc. including

making good the wall ceiling and floor.

Providing and fixing cast iron (Spun) Nahni trap of the following nominal

diameter of self cleaning design with C.I. screaed down or higned grating

including cost of cutting and making good the walls and floor 100 mm inlet and

mm outlet.(C)100mm dia.

Providing and fixing water closet squatting Pan (Indian type W.C.Pan)

size 580 mm (Earth work, bed concrete, foot rest and trap to be measured

and paid for separately) (A) Vitreous China. (I)Long pattern = White colour

Provdg. & fixing wall mounted White / Color Vitreous China European

water closet with integral P trap of "Cera" - Clair Series or equivalent

incl. seat cover , Chair Bracket etc. complete as per direction of engg. In

Providing and fixing wsh down water closet (Europe an type, W.C.Pan)

with integral P or S trap including jointing the trap with soil pipe in Cement

121 5 Mortar1:1 (1- Cement:1-fine sand) (Seal and cover to be measured and paid 1290.80 Each

forseparately) (A) vitreous China Pattern :(i) in white colour

Provdg. & Fixing Flat Back Large Urinal of White/ colour of "Cera" or " Hindware"

122 6 incl. C.P. Brass waste coupline , waste pipe, pvcconnection etc. 1850.00 No.

Complete.( size 635 x395x420 mm )

Providing & Fixing Angle cock of " Ess Ess" - Trend series or equivalent

123 10 standard make as approved by engg. in charge all complete. (N.S.) 675.00 No.

Providing and fixing 100 mm size P or S trap for water closet squatting

124 10 pan including jointing the trap with the pan and soil pipe in cement Mortar1:1 311.85 Each

(1-Cement : 1-Fine sand)(A) Vitreous China.

Providing and fixing wash basin with single hole for pillar tap with C.I.or M.S.

brackets painted white including sutting holes and making good the same

but excluding fittings. (A) Vitreous China: (ii) Flat Back wash basin 550 mm x v

400 mm size.(i) In white colour.

Providing and fixing Kitchen sink with C.I. or M.S. brackets, painted white

126 8 including cutting holes in walls and making good the same but excluding 2257.69 Each

fittings. © Vitreous China Sink. (i) 600 mm x 450 mmx 150 mm size

Providing and fixing 600 mm x 450 mm bevelled edge mirrror of superior

127 15 glass mounted on 6 mm thick A.C. sheet or ply wood sheet and fixing to 825.48 Each

wooden pluge with C.P. brass screws and washers.

Providing and fixing chromium plated brass halftrun flush cock of approved quality

including fixing in pipe line etc. complete.

Provdg. & fixing White / Color Vitreous china Counter wash basin with signle

hole for pillar tap of "Cera " - Concord series of 550 x425 mm size to be fiited

in stone counter with necessary brackets painted white incl. cutting holes

129 10 and making good the same .Cost Includes P/F C.P. brass waste coupline, 2950.00 No.

32 mm dia fisher union ,15 mm dia. Pillar cock & Angle cock of " Ess Ess"-

Trend series ,32 mm dia. Waste pipe etc. complete as per dir. of engg.

Providing and fixing wash basin with single holefor pillar tap with C.I. or M.S.

brackets painted white including sutting holes and making goodthe same but

excluding fittings.(A) Vitreous China:(ii) Flat Back washbasin 550 mm x v400mm

size. (i) In white colour.

Providing & Fixing S.S.304 Grade Sink of Nirali / Krishna or Equivalent

131 5 Make for Kitchen Platform of size : 24":x18" as per Direction of engg. In 4650.00 No.

Providing and fixing C.P. brass towel rail comlete with C.P.brass brackets

132 10 fixed to wooden plugs with C.P. brass scews.(B) 600mm x 20mm size. 597.22 Each

Providing and fixing 600 mmx120 mm glass shelf with C.P. brass bracket and

guard rail complete mixed to wooden plug with C.P.brass screws.

134 5 Providing and fixing toilet paper holder. (A) C.P.Brass 414.53 Each

Providing and fixing screw down bib taps of following size. (A) Brass screw

down bib tap polished bright.

10 (i) 15mm dia. 184.98 Each

10 (ii) 20mm dia. 212.68 Each

Providing and fixing screw down bib taps of following size. (B) Brass chromium

plated screws down Bib Tap.

15 (i) 15mm dia. 184.98 Each

10 (ii) 20mm dia. 212.68 Each

Providing and fixing screw down bib taps of following size. © Gun metal

screw down bib tap.

25 (i) 15mm dia. 157.29 Each

15 (ii) 20mm dia. 176.09 Each

Providing and fixing pillar tap, capstan head, screw down high pressure

with screws, shanks and back nuts.

20 (i) 15mm dia. 305.67 Each

15 (ii) 20mm dia. 351.18 Each

Providing and fixing Gun metal check or non-return fullway wheel valve.

10 (i) 15mm dia. 184.98 Each

5 (ii) 20mm dia. 201.80 Each

15 (III) 25 MM DIA 416.47 Each

12 (E) 40mm dia 656.86 Each

Providing and fixing chromium plated brass half trun flush cock of approved

quality including fixing in pipe line etc. complete.

15 (i) 20mm dia. 252.26 Each

10 (ii) 25mm dia. 261.16 Each

5 (iii) 32mm dia. 273.03 Each

Providing and fixing Urinal or approved quality including conecting

the Urinal with waste pipe , tap etc.complete. (A) White earthen ware flat

back or corner type size 430mm x 260mm x 350mm.

Providing and fixing Urinal of approved quality including connection

142 15 with trap and with integral longitudinal flush pipe. (A) Squating plate 1535.63 Each

pattern white earthen ware 550mm x 300mm.

Providing and fixing chromium plated, bottle trap with necessary couplings

of approved quality for wash basin.

Providing and fixing ball cock ofapproved quality as directed. (A) Copper

Metal (i) 25mm dia.

Providing and fixing ball cock of approved quality as directed. (B)Abonite (i)

Filling with good Quality thor as and where directed by the Architect /

Engineer-in-charge, in sunk in layers of 15 cm. thickness, including watering,

ramming well etc. complete, as directed by the Architect / Engineer-in-charge .

Providing laying and jointing in true line and level 15 mm dia. U.P.V.C. Pipe (SCH-

40) for cold water including fittings make PRINCE/ SUPREME/ ASTRAL/

FINOLEX or equivalent as approved by Engineer In Charge. Pipe shall be

147 35 fixed on the wall with the help of clamp at every two metre C/C or shall be 71.93 Rmt

concelled as directed including necessary fittings etc. including testing of

pipe and joints and fixing the same with solvent, including cost of all

materials.adhesive

Providing laying and jointing in true line and level 25 mm dia. U.P.V.C. Pipe (SCH-

40) for cold water including fittings make PRINCE/ SUPREME/ ASTRAL/

FINOLEX orequivalent as approved by Engineer In Charge. Pipe shall be

148 15 fixed on the wall with the help of clamp at every two metre C/C or shall be 90.93 Rmt

concelled as directed including necessary fittings etc. including testing of

pipe and joints and fixing the same with adhesive solvent, including cost of

Providing laying and jointing in true line and level 32 mm dia. U.P.V.C. Pipe

(SCH-40) for cold water including fittings make PRINCE/ SUPREME/

ASTRAL/ FINOLEX or equivalent as approved by Engineer In Charge.

149 15 Pipe shall be fixed on the wall with the help of clamp at every two metre C/C 117.97 Rmt

or shall be concelled as directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with adhesive solvent, including

cost of all materials.

Providing laying and jointing in true line and level 40 mm dia. U.P.V.C. Pipe

(SCH-40) for cold water including fittings make PRINCE/ SUPREME/

ASTRAL/ FINOLEX or equivalent as approved by Engineer In Charge.

150 10 Pipe shall be fixed on the wall with the help of clamp at every two metre C/C 146.65 Rmt

or shall be concelled as directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with adhesive solvent, including

cost of all materials.

Providing laying and jointing in true line and level 50 mm dia. U.P.V.C. Pipe

(SCH-40) for cold water including fittings make PRINCE/ SUPREME/

ASTRAL/ FINOLEX or equivalent as approved by Engineer In Charge.

a 10 Pipe shall be fixed on the wall with the help of clamp at every two metre C/C 193.73 Rmt

or shall be concelled as directed including necessary fittings etc. including

testing of pipe and joints and fixing the same with adhesive solvent, including

cost of all materials.

Providing in line level plumb, fabricating and fixing three row horizontal

barbed wire fencing and punched tape concertina coil of 9 turns per meter of

610 mm dia fixed with clips on top of the angle iron posts. The punched tape

concertina coil having sharp barbs at every 25 mm spacing shall be 0.5 mm

151 8 thick and 19 mm width and weighting 13 kg/100 mt. (Average) as per manufacture's 390.00 Rmt

specification. The rate shall also include providing and fixing

mt.total long MS angle 40 x 40 x 6 mm @3.00 mt.c/c spacing embaded in RCC

column, angle posts shall be painted with one coats of red oxide and two coats of

enamel paint of approved quality at top compound wall.

Fixing sun film for protection sunlight in black or any colour as as directd by

engineer In Charge.(Market rate)

Providing & Fixing 3 mm thick F.R.P.sheet of Approved Quality & Color /

Pattern as per Consultant's design also includes required fabrication structure

in the grid of 2'-0x2'-0 size using hollow pipe of16 gauge & size 2"x1" &

153 6 1"x1" ,G.I. & Bitumen Washers, Silicon paste application for fixing the sheet 1930.00 SqM

. Rate also includesnecessary bending, cutting, labor charges , Zinc Primer coat

& Two coats of oil painting of color as approved by consultants & making

good the wall. (N.S.)

Providing 2 mm thick F.R.P. Gutter with necessary M.S. Supporting Brackets.

Hiring charges for J.C.B.machine inclduing cost of fuel, operator, dirver

etc.. ( 12 hours sift day/night) (N.S.)

To provide tractor with hydraulic trolley, driver, 4 Nos. of Labor with all tools like

bucket drum, showels, trikam, pavadas, etc,, to carryout different

156 10 works during monsoon for 12 Hrs. Shift. Work shall be carried out as per 1661.02 No.

the instrucitons of Engineer In-Charge.No extra charged shall be paid for night shift.

Roller Blind Providing and fixing Roller Blind curtain fixed on window

level on wooden batten and curtain lift with cotton thin rope, make of

157 10 aerolax or equivalent design and colour as per instruction by engineer – 3285.00 Smt

in – Charge with necessary hardware fitting, material and labour etc

Providing & Fixing Door closer - Door closers (Heavy type of 765 number) Hardwire

or Everite Prabhat or Equivalent

Providing and fixiing M.S. Fan clamps type 1 of 16 mm dia M.S. bar bent to shape

159 5 with hooked ends of R.C.C. slabs during laying incl. painting the exposed protion of 124.74 No.

loops, all as per standard design complete.

Providing cement vata (10cm. x 10 cm. size) quarter round in cement mortar 1:1

including neat cement finishing, watering etc. complete.

161 10 Making Water connection from exi.Muni. Water line (N.S.) 250.00 No.

Providing and applying fibere reinforced cementitious micro concrete

work in cellings and beams incl.mixture of CEMSCREED HM

(F) fair mate company material, FBR bonding agent material with water

162 50 in suItable proportion anti corrosive treatment on exposed beam,celling steel 530.00 Smt

bars with safeCore R incl.all kind of labour etc.comp.including three coat

of white wash.(Approved Rate)

Providing and Fixing 1 H.P. Electrical monoblock or submarcible water pumps

163 5 withmotor and required cable and switch board of approved brand and make 6800.00 Set

etc.comp.as directed.

.Providing TMT Bar FE 415 reinforcement for R.C.C. work including bending,

binding and placing in position complete up to floor two level

ProvidingTMTBarFE500/500Dreinforcement for R.C.C.workincluding

bending,binding and placing in position complete upto floor two level placing in

position complete upto floor two level placing in position complete upto floor two

Providing and fixing 30mm thick solid both side prelam PVC door shutter (sintex

164 15 door-equivalent) with necessary alluminium fitting with EL-7 section frame 2867.00 Smt

Conveyance charge of Earth,Lime, Murrum, building rubbish earch manure or

165 50 sludge and excavated rock and fly ash,aggregate of any kind etc.comp.upto 5 km 235.51 Cu.M.

Providing and laying polished granite stone slab 18 mm thick in risers of steps,

dedo and pllars laid on 10 mm thick cement mortar 1:3 (1 cement:3 coarse sand)

and jointed with gray cement slurry including rubbing & polishing etc.complete.

Wall panelling with 12 mm MDF fixed to existing alluminium framing and making

167 10 grove as per design and finished with royal plastic paint as per instruction of 1688.00 Smt

engineer incharge. (N.S.)

Providing and laying 15mm bamboza wooden flooring as per architect's

drawing with all necessary details as directed by the project

consultants. Use underlay for better result as per Detail specifications and

directed by the project consultants. (N.S.) (Approved Rate )

Applying two coats of Birla (whitecementbased) or Asian

(acryliclapy-putty) or equivalent & two coats of primer of approved brand and

manufacture on new wall surface to give an even shade including thoroughly

brushing the surface free from mortar dropping

Finishing wall with weather proof exterior emulsion paint on wall surface (two coats)

to give an required shape evenshade after thoroughly brushing the surface to

remove all dirt, and remains of loose powdered materials.etc complete

Providing and fixing flush door shutters, solid core construction with frame

of first class hardwood with cross board and face veneer or plywood face

panels, with both side 1 mm laminate finishing including anodized

aluminum butt hinges with necessary screws. Decorative type and pine

wood core anodized minimum 3 no 150 mm long aluminum butt hinges in

171 5 flush door shutters with 2 no of brass holdfast 325 mm long 1 no brass 4686.36 Smt

tower bolt 250 mm long and two no of 150 mm long brass door handle .

Decorative both side laminated Flush door 35 mm thick. with frame of 10 cm

x 7 cmt Indian teak wood frame including all necessary fitting fixtures

hardware screw and adhesive etc fixing up to all lead and lift height up to

mtr from GL etc complete as per direction of engineer in charge

P/M/F chainlink jali 8'x4' size as per details sketch & instructionof engineer in

charge same as lal darwaja garden pattern consisting of 3'dia. M.S black pipe 'A'

class 5'4" ht. fixed at 8'9" c/c in C.C 1:2:4 block of 9"x9"x9" size chain link jali of size

172 5 2"x2"x10 gauge fixed in 35x35x5 mm MS angle frame 8'x4' size with MS flat of size 1230.00 Rmt

25x3 mm welded jali etc.comp.The jali is to be welded to MS pipe with MS flat as

instruction given.The M.S pipe and the M.S angle frame are to be painted one coat

of primer and two coats of paint as directed in line and level. (N.S)

Providing & Fixing masonary wall with porbandar lachiya stone with well dressed

grooveas per directed by engg.in charge for foundation, plinth or super structure

level (above plinth level upto floor two level) in cement mortar 1:5 (1-cement : 5-fine

sand) incl.pointing the joint with white cement and yellow oxide powder in proportion

to match stone colour the joints should be thread grooved as per exi. lake stone

pitching apperance

5 (A) stone masonary wall/stone dressed single faced (size 15"x8"x9") 8990.00 Cmt

5 (B) stone coping (size 15"x8"x4") 510.00 Rmt

5 (C) stone coping (size 15"x8"x9") 790.00 Rmt

5 (D) stone column (size 15"x15") 10710.00 Cmt

5 (E) stone column top (size 20"x20"x9") 685.00 No.

Supplying and fixing of 300 mm-L x 15 mm-B x 380 mm-H Kerb block for

Footpath in M-20 grade using 20 mm nominal size black trap aggregate

of Sevaliya/Timbaor equivalent quality for pre-cast blocks,

reasonablyexposed finish/ formwork , mould with well

equippedwith vibratory system for kerb stones of approved design including

curing, etc. complete, including thecost of formwork etc. complete. The

174 10 rate shall also include necessary cutting of asphalt, fixing the 393.00 Rmt

Kerbstones in line and level on 5 cm thick sand bedding

withnecessary equipments and materials. The rate shall also include the

flush pointing in CM (1:3) for all joints of the kerb stones. Filling of zari alone the

sides of the kerbstone fixed with Bituminous concrete

Bituminousconcrete / C.C. mixed in proper position to flush withthe road

surface as directed by Engineer in change to form a portable mixture.a)

Laying on 5 cm thick Sand Bedding

Providing and Laying of Rubber Moulded Paver Block Grey/Coloured 60 mm thick,

M-35 Grade of any size shape (Usually Uni-Paver Blocks) using black trap good

quality aggragate of 20 mm nominal size for footpath,parking areas, service lanes

and other areas as mentioned in the drawing / instruction of engineer in charge.

Cost includes formworks using rubber mould, Rate providing and laying paver

blocks as per required grading and specification. The paver block shall be

175 25 mechanically compacted. The work of paving blocks shall be executed in line and 429.00 Smt

level by skill mason of flooring work only. It should be laid in such a way that the no

cutting of the paver block to be necessary. if cutting of paver block necessary then it

should be cut by machine only and carting. The finished surface of the paver block

shall have resonably good, plain finished. Paver blocks shall be compacted and

shall be relaid if necessary. Gravel or such type of materials shall not be allowed for

production. Laying on 5 cms thick sand

Provoding and fixing flush door shutters, solid core construction with frame of first

class hard wood with cross board and face veneer or ply wood face panels,

including anodised alluminium butt hinges with necessary screws. (B) Non-

176 28 decorative type and block board core anodised alluminium butt hinges in flush door 1779.97 Smt

shutters (2) 35 mm thick. Labour work for fixing any kind of paving with cement

pointing in CM 1:2, including watering, ramming etc comp. as dir.For pavement

I) Laying on Sand bedding as per requirement to fix the C.C.Block / Nibhada Stone

in Line & Level

Box type metal letters forming composite box made from 1mm thick stainless steel

plate of grade 304 having brush finish of following font size to be fixed at Main Gate

in english and or Gujrati and including fixing charges approved before fixing by clent

A 5 400mm high 1000.00 Nos.

B 5 300 mm high 750.00 Nos.

C 5 230 mm high 565.00 Nos.

Providing and fixing false ceiling at all height including providing and fixing of frame

work made of special sections, power pressed from M.S. sheets and galvanized

with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and

consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm

and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash

fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to

the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of

179 50 required size and other end of angle hanger fixed with intermediate G.I. channels 850.00 Smt

45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the

ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm

each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a

direction perpendicular to G.I. intermediate channel with connecting clips made out

of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter

channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the

perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm

Providing & Fixing SPEED BUMP - #2 No (1 black, 1 yellow) 350 x 500 x 50 mm,

Size per color End Cape 350 MM x 175 MM x 50 MM TOP DESIGN - Lining Top

flat ANTI SKID PATTERN FOR GRIP COLOUR :- YELLOW & BLACK BODY

180 1 MATERIAL :- MODIFIED THERMOPLASTICS (Polymer Rubberized ) • ECO 2185.00 Rmt.

FRIENDLY RECYCLE RUBBER Packing :- 4 pcs/ woven Bag Load Capacity :-

MT Fitting ( Fixing on TRAKE) :-4 holes & END CAPE :- 2 HOLE HEX Bolts with

Washer Epoxy for Bolt Fitting etc. complete as directed by EIC .

Providing and fixing of Roller blind curtain/blackout. The fabric shall be woven from

formulated platisol extruded over a polyaster yarn.The fabric shouldl be weaved to

181 5 provide subtle view of the side of the blind and should offer elimination of glare and 2610.00 Smt

sunlight radiance upto a minimum of 80%.The fabric shall be flame retardant.

Providing and fixing PVC/Gpsysum plain colour false ceiling with grid type with

aluminium frame from gypsteel, fastners ,props, Finishing as per

182 5 architectural drawing allowing openings for A.C. Diffusers, 933.00 Smt

Light/Electrical Points etc –complete, Prior to fixing on frame.(Brand :

Anutone or equivalent ) (N.S.) or as directd by engineer In Charge.

Provdg. & laying S.W. Gully trap with brick masonry chamber & water tight

183 5 G.T.Stone including fixing of covervSquare mouth trap 100 mm x100 mm size P- 1263.15 No.

Providing cement vata (10cmx10cmsize) quarter roundin cement mortar 1:1

including neat cement finishing, waterin getc. complete.

Providing and laying (to level or slopes) and jointing with stiff mixture of Cement

185 3 Mortar in proportion 1:1 Salt glazed stoneware pipes including testing of pipes and 211.05 Rmt.

joints complete.(A) 100mm dia.

Providing and laying (to level or slopes) and jointing with stiff mixture of Cement

186 5 Mortar in proportion 1:1 Salt glazed stoneware pipes including testing of pipes and 288.23 Rmt.

joints complete.(B) 150mm dia.

Constructing brick masonry chamber for underground C.I. Inspection chamber and

bends with bricks having crushing strength not less than 35Kg/Cm2 in C.M. 1:5 C.I.

cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of

cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame

187 2 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone 2903.89 Each

aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with

cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and

bed concrete etc. complete.(i) Inside dimensions 455mmx 610mm and 450mm

deep for single pipe line.

Constructing brick masonry chamber for underground C.I. Inspection chamber and

bends with bricks having crushing strength not less than 35Kg/Cm2 in C.M. 1:5 C.I.

cover with frame (Light duty) 455mm x 610mm intenal dimensions total weight of

cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and Wt. of frame

188 3 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded stone 3624.51 Each

aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm thick with

cement mortar 1:3 finished smooth with a floating coat of neat cement on walls and

bed concrete etc. complete.(i)Inside dimensions 500mm x 700 mm and 450mm

deep for pipe line with one or two inlets.

Providing, supplying and fixing precast C.C. blocks (M-20) edge kerb having size of

75 x 300 x 300 mm depth and as per design conveying it to the site, jointing into

C:M 1:3 and racking out the joints incl. necessary excavation of asphalt, soil

etc..completed.

Constructing a cooking Sandwich platform 60 cm. width and 70 cm high resting on

B.B.Masonry walls 23 cm.thick in C.M.(1:6) with (ii) Fixing black Granitee 30mm

thick laid on precast R.C.C. (1:2:4) slab with plastering on exposed faces of wall in

C.M. (1:4) etc complete

Providing and fixing hard drawn steel wire fabric 75mm x 25mm mesh or weight not

191 5 less than 7.75 kg. per Sq.M. to window frames etc. including60 x 20mm beading of 754.65 Smt

Providing & fixing 15 cm wide chicken mesh jali with nails & then application of

mm plaster on R.C.C.& masonary joints as per dir.of engg.in charge

Providing and laying cement concrete flooring 1:2:4 (1-cement : 2-coarse sand : 4-

193 5 graded stone aggregate 20mm nominal size) laid in one layer and finished with a 348.08 Smt.

floating coat of neat cement. (A) 50mm thick.

Providing and constructing, Underground (U/G) water tank of specified capacity, on

specified location, for all depths, in controlled CC of M-200 grade with bottom slab,

top slab and RCC walls, including cost of form work and reinforcement,with inside

194 10 and outside plaster in CM 1 :3 and water proofing treatment as per IWP 6.50 Litre

specification,including injection, grouting, etc. complete. The rate includes for

providing and fixing two nos. 0.6m. x 0.6 m. size medium duty CI manhole cover/s

at top, including wash out pipe line and inlet and outlet connections etc. complete.

Providing and fixing PVC Printed pain colour false ceiling with grid type with

alluminium frame consisting of 600mm x 600mm 3mm thick plain PVC sheet used

as panel insert in a frame work made using anodized alluminium T section of size

x 1 (235 x 25mm, 19 gauge or 1 mm thick) in square pattern of grid sizes of 2 x

195 5 (600 x 600mm) The alluminium frame work is supported from the cceiling with the 300.12 Smt

help of G.I. hook and G.I. wire/6mm M.S. rods of required sizes to maintain proper

level etc. The aluminium frame work is supported on side wall with the use of

alluminium L section of size 1 x1 (25 x 25mm) angles etc. complete as per direction

of Engineer in charge. Manufactures specification and drawing.

Providing and supplying of labour for necessary manual excavation, cleaning,

196 10 Shifting of Material Or any other, or for any other work as directed by Engineer In 551.00 No

charge. The Rate includes Handcart with Mazdoor

A 5 Mukadam/supervisior/karigar 425.00 No

B 10 Fitter/Plumber/Mason 697.00 No

C 5 WELDER/ Gas cutter at Day /night 689.00 No

Supplting of welding machine / gas cutter including cost of welding rods/gas,

Transportation, including carting from site to work place.

E 15 Mazdoor at Day Female 450.00 No's

E 15 Mazdoor at Day Male 493.00 No's

Supplying electric breaker machine for RCC slab or asphalt demolishing work on

site by using operator, fuel, power supply etc.complete as directed. (no payment

197 10 should be allowed for non working condition of machinery and for pipe line 1071.42 Shift

excavation and M.H. work. Allowed only for break down work) (Based on Previously

approved rate by CE sir )

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR 13.5)

PIPE having National Sanitation Foundation (NSF) seal for potable water of

following dia. Nominal bore tube fittings and clamps including making good the wall,

ceiling and floor etc. complete.

A 15 15 MM DIA 165.21 Rmt

B 5 20 MM DIA 202.97 Rmt

C 10 25 MM DIA 247.25 Rmt

D 15 32 MM DIA 330.36 Rmt

E 10.00 40 MM DIA 437.66 Rmt

199 5 50 MM DIA 647.30 Rmt

Supplying and fixing C.I. cover 300mm x 300mm without frame for Gulley trap

(Standard pattern) te weight of cover to be not less 4.53 Kg.)

Providing and fixing to wall ceiling and floor 10.0Kg.F/Cm2 working pressure

polythene pipes of the following out side Dia. Low densidy, complete

with special falnge compression type fittings, wall clips etc. including

making good the wall ceiling and floor.

Providing, Fabricating & Fixing signage's using 304 grade Stainless steel 1.5 mm

thick brushed steel finish plate (2 nos) with 8mm thk. Acrylic sheet covered with

vinyl of approved colour, sandwiched between two S.S plate and fixed with s.s

struds . Sandwiched plates should be fixed in 12mm X 12mm S.S 1.5mm thk.304

202 100 grade frame and punched (laser cut) lettering carried out on both the s.s plates of 69.00 Sqinch

required size and text as directed by Engineer and hanged to ceiling with the help

of S.S 8mm thick chain at both ends with making all the fixing arrangement to the

ceiling and to the plate etc. complete all As per drawings and design supplied by

architect and instruction given by authority and E.I.C.

Providing and applying approved coloured chips 20mm thick STONE CREAT

PLASTER for exterior / interior side on wall up to full height from ground level

consisting of 12mm thick backing coat of CM 1:3 (1 cement : 3 Bodeli sand) and

8mm thick finishing coat of CM 1:1 (1 cement (Grey / White / Colour : 1 stone grit

(approved coloured chips)) including providing & fixing 300mm wide strip of chicken

net at vertical and horizontal joints of RCC and masonary including 10mm

alluminium channel for expantion joint / grooves, curing, necessary scaffolding in

true line and level etc. complete as directed by EIC.

Providing and laying plain dressed surface machine cut dhrangadhra stone slab of

approved quality for dedo, & risers of steps, etc. over 12mm (Average) thick base

of cement mortar 1:4 (1-cement : 4-coarse sand) or L.M. 1.1.5 laid over and jointed

10 with cement slurry including surface dressing, rubbing, providing grooves, rounding 2289.67 Sqmt

the edges and polishing for proper finishing etc. complete size & pattern as per

drawing/instructions of EIC/Consultant.

Proviging and Fixing Storage Shutter made out of 50mm X 25 mm Indian

Teakwood Frame and 18 mm Ply Board. With 1 mm thick laminate finish in the front

and 0.8 mm thick Laminate on Back Side with 12 mm thick Indian teakwood

beading. The scope also include providing and fixing s.s. finish hardware as per the

204 20.00 Requirement. The rate include cost of all labour, material and with all hardware like 6805.00 Sq.mt.

handle, magnate, tackels, adhesive, screws, etc.for satisfactory completion of this

items.All Exposed Wood Work shall have malamine polish etc. complete.

Providing & Fixing Sun Control Reflective Type Film / Frosted Film as Selected by

205 90.00 Architect/ Engg. In Charge For Glass Doors / Windows etc. as Directed. 646.37 Sq.mt.

Providing & Fixing in Position Vertical Roller Blinds with Minimum 3 % and

Maximum 5 % Light Transperace Screen Fabric Incuding Providing & Fixing of

Powder coated G- Channel at the Topof Window with necessary Screw , Cleats etc.

and PVC Roller ( Weight Pipe) and PVC Chain For Up and Down Movement of

206 25.00 Blinds etc. of Approved Make and as per Drawings / Instruction of Engg. in Charge 1372.03 Sq.mt.

For All Colors and Shades. Rates Includes all Lead and Lift For All Floor Level, All

Height , All Material , Accessories, Fixing , Scaffolding , Labor etc. Complete in All

Respects. All Required Accessories & Material must be From Same Manufacturer.

Providing corrugated G.I. sheet of class-3 roofing fixed with glavanished iron J or L

Hooks, Bolts and nuts 8mm diameter with bitumen and G.I. limpet washer or G.I.

limpet washer. filled with white lead complete excluding the cost of purlins, Rafters

and Trusses.(1) 0.80 mm thick sheet.

Providing valleys 900mm overall in plain 1.6mm thick G.I. sheet fixed with G.I. J or

208 25.04 L Hooks, Bolts and nuts glavanised iron J or L Hooks Bolts and nuts 8mm dia G.I. 1042.78 Sqm

Limpet and bitumen washers complete

Structural steel work ( Confirming to IS 4923-1997) riveted, bolted or welded in

builtup for all type sections, in framed work, including cutting, hoisting, fixing in

209 10.00 position and applying a priming coat of approved steel primer all complete as per 126.68 Kg

the structural designs and directions of Engineer in charge.Column ( 122 x 61 x

Providing and applying approved coloured chips 20mm thick STONE CREAT

PLASTER for exterior / interior side on wall up to full height from ground level

consisting of 12mm thick backing coat of CM 1:3 (1 cement : 3 Bodeli sand) and

210 20.00 8mm thick finishing coat of CM 1:1 (1 cement (Grey / White / Colour : 1 stone grit 709.60 Sqmt

(approved coloured chips)) including providing & fixing 300mm wide strip of chicken

net at vertical and horizontal joints of RCC and masonary including 10mm

alluminium channel for expantion joint / grooves, curing, necessary scaffolding in

true line and level etc. complete as directed by EIC.

Providing and laying 18 mm thick polished granite stone machine cut in single piece

(Max. available) in sill and jambs of door ,window,ventilation & lift wall

cladding,staircase flooring landing, risers & treads, skirting laid over 10 mm thick

211 10.00 cement mortar 1 : 3 (1 cement : 3 coarse sand) and jointed with grey cement slurry 3279.00 Sqmt

with matching pigment incl. rubbing and polishing,half rounding edge and incl. fixing

of hilty fastener at every 1/3 span of sill as required size etc. complete colour and

shed as approved by architect engineer in charge.

Supply and Fixing of Auditorium seating Fabricate Auditorium seating with

Synchronized Push back Chair with Ergonomically designed Poly Urethane foam

for seat and back made my DOW chemical with High Pressure moulding technology

to achieve long life performance, upholstered with stitched 3 Layer 100% Yarn

Dyed fabric Upholsteries. Chair profile with the seat in Normal position and without

a tablet arm should not be more than 75 cm. Chair pushback mechanism should

consist of 2 nos. x DIA 50 mm ZYTEL Based Rollers which is supported by AXIAL

shaft of DIA 12 mm is Driven by radial movement of 4 set of Swing Arms of size

212 1.00 25mm x 6 mm thickness with 9990.00 No

Orbital Riveted Solid Dia 8 mm Barrel MS Rivets. The pushback movement is

achieved by synchronised movement of 04 links mounted on Two Number of

triangular Symmetrical housing of size 27 cm x 23 cm duly embossed for extra

strength by 1.2 cm made up by 0.12 cm CRCA compliance to IS 513. The entire

mechanism should be made in India and should have total weight 8.5 kg duly

Powder Coated – NO SPREAY PAINT Part should be used for the chair of The

Seat Size should be 42 cm x 48 cm the Back height should be 70 cm with

ergonomically designed seat and back cushions. Chair should be available in 20”,