Construction of new wharf, Shed, Amenities, connectivity road, Office for Railway employees is required with water, urinal and toilet facility Lighting arrangement at Rakhitpur and Improvement of Goods shed under ADEN/2/DHN.

BI-(General) CPWD DSR 2021

CII-Reinforcement (DSR-2021)

Item Breakup - BI-(General) CPWD DSR 2021

local sand, with common burnt clay non modular bricks. 12.0 ROOFING 12.37S RAIN WATER SPOUT AND PIPE Providing and fixing 100 mm diameter and 60 12.37 cm long rain water spout in cement mortar 1:4 (1 cement : 4 fine sand). 26 12.37.1 Stone ware spout Each 96 142.1 13641.6 Providing and fixing M.S. holder bat clamps of approved design to C.I. or S.C.I. rain water pipes embedded in and including cement 12.38 concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and cost of cutting holes and making good the walls etc. : 27 12.38.2 150 mm diameter Each 96 328.55 31540.8 Providing, fixing and embedding sand cast iron accessories for rain water pipes in the masonry 12.40 surrounded with 12 mm thick cement mortar of the same mix, as that of masonry (lead caulking will be paid for separately): Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 12.41 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 28 12.41.2 110 mm diameter Metre 2448 319.75 782748 DHANBAD DIVISION-ENGINEERING/EAST CENTRAL RLY Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes 12.42 conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 12.42.5 Bend 87.5 degrees 29 12.42.5.2 110 mm bend Each 120 132 15840 12.42.6 Shoe (Plain) 30 12.42.6.2 110 mm Shoe Each 120 115.95 13914 12.50 Providing and fixing precoated galvanised iron Sqm 3200 671.55 2148960 profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to 31 avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 13.0 FINISHING 13.1S CEMENT PLASTER (IN FINE SAND) 13.1 12 mm cement plaster of mix : 32 13.1.2 1:6 (1 cement: 6 fine sand) Sqm 337 282 95034 13.4S CEMENT PLASTER (IN COARSE SAND) 13.4 12 mm cement plaster of mix : 33 13.4.2 1:6 (1 cement: 6 coarse sand) Sqm 135 294.35 39737.25 13.6 20 mm cement plaster of mix : 34 13.6.1 1:4 (1 cement: 4 coarse sand) Sqm 7 421.4 2949.8 13.16S 6MM CEMENT PLASTER 35 13.18 Neat cement punning. Sqm 273 67.8 18509.4 13.44S EXTERIOR FINISHING Finishing with Deluxe Multi surface paint system 13.48 for interiors and exteriors using Primer as per manufacturers specifications : 13.48.3 Painting Steel work with Deluxe Multi Surface Sqm 392 140.05 54899.6 Paint to give an even shade. Two or more coat 36 applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.80 ltr/10 sqm of approved brand and manufacture 18.0 WATER SUPPLY 18.4S PP-R PIPES Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801 UV stabilized & anti - microbial fusion welded, having thermal stability for hot & 18.6 cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, including trenching, refilling & testing of joints complete as per direction of Engineer-in- Charge. -External work 37 18.6.7 PN - 10 Pipe, 75 mm OD (SDR-11) Metre 100 879.45 87945 18.6A Providing and fixing PPR Unions 38 18.6A.5 PPR Union 50mm Each 3 764.05 2292.15 39 18.6A.7 PPR Union 75mm Each 4 1687.2 6748.8 18.7S C.P.V.C. PIPES DHANBAD DIVISION-ENGINEERING/EAST CENTRAL RLY Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making 18.10 good the walls etc.-Internal work - Exposed on wall 40 18.10.3 25 mm dia nominal bore Metre 600 491.2 294720 Providing and fixing G.I. Pipes complete with G.I. fittings and clamps, i/c making good the 18.11 walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : 41 18.11.1 15 mm dia nominal bore Metre 72 485.2 34934.4 Providing and fixing G.I. pipes complete with 18.12 G.I. fittings including trenching and refilling etc.-External work 42 18.12.4 32 mm dia nominal bore Metre 70 457.7 32039 43 18.12.5 40 mm dia nominal bore Metre 50 558.35 27917.5 44 18.12.6 50 mm dia nominal bore Metre 70 654.2 45794 45 18.12.7 65 mm dia nominal bore Metre 60 768.6 46116 46 18.12.8 80 mm dia nominal bore Metre 50 919.1 45955 18.15S BRASS FITTINGS Providing and fixing brass bib cock of approved 18.15 quality : 47 18.15.1 15 mm nominal bore Each 24 303.85 7292.4 Providing and fixing brass stop cock of 18.16 approved quality : 48 18.16.2 20 mm nominal bore Each 6 327.95 1967.7 Providing and fixing gun metal gate valve with 18.17 C.I. wheel of approved quality (screwed end) : 49 18.17.1 25 mm nominal bore Each 4 532.35 2129.4 50 18.17.3 40 mm nominal bore Each 2 707.3 1414.6 51 18.17.4 50 mm nominal bore Each 2 878.25 1756.5 52 18.17.6 80 mm nominal bore Each 3 2227.6 6682.8 Providing and fixing gun metal non- return 18.19 valve of approved quality (screwed end) : 18.19.6 80 mm nominal bore 53 18.19.6.1 Horizontal Each 2 3134.8 6269.6 C.I. SLUICE VALVES/ FIRE HYDRANTS & 18.31S FIXTURES Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertions etc. 18.31 (the tail pieces if required will be paid separately) : 18.31.1 100 mm diameter 54 18.31.1.2 Class II Each 4 4500.25 18001 Providing and fixing G.I. Union in G.I. pipe 18.46 including cutting and threading the pipe and making long screws etc. complete (New work) : 55 18.46.2 20 mm nominal bore Each 2 289.05 578.1 56 18.46.3 25 mm nominal bore Each 4 369.35 1477.4 57 18.46.4 32 mm nominal bore Each 4 409.45 1637.8 58 18.46.5 40 mm nominal bore Each 3 523.2 1569.6 59 18.46.6 50 mm nominal bore Each 3 706.7 2120.1 60 18.46.8 80 mm nominal bore Each 4 1061.25 4245 18.48 Providing and placing on terrace (at all floor Litre 10000 9.7 97000 levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking 61 arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 18.54S PTMT FITTINGS DHANBAD DIVISION-ENGINEERING/EAST CENTRAL RLY Providing and fixing PTMT bib cock of approved 18.54 quality and colour. 18.54.1 15mm nominal bore, 86 mm long, weighing not Each 4 109.85 439.4 62 less than 88 gms 23.0 RAIN WATER HARVESTING & TUBEWELLS Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, 23.1 including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level. 23.1.1 All types of soil 63 23.1.1.1 300 mm dia Metre 320 592.05 189456 Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, 23.2 including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & upto 150 metre depth below ground level. 23.2.1 All types of soil 64 23.2.1.1 300 mm dia Metre 120 690.7 82884 Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, 23.3 conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 65 23.3.3 200 mm nominal size dia Metre 120 951.95 114234 23.5 Supplying, filling, spreading & leveling stone cum 66 1302.3 85951.8 boulders of size range 5 cm to 20 cm, in 66 recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge. 23.6 Supplying, filling, spreading & leveling gravels cum 32 1309 41888 of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in 67 required thickness, for all leads & lifts, all complete as per direction of Engineer-in- charge. 23.7 Supplying, filling, spreading & leveling coarse cum 32 1309 41888 sand of size range 1.5 mm to 2 mm in recharge 68 pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge. Total 37335337.80

Item Breakup - CII-Reinforcement (DSR-2021)