REPAIR TO BIRD PROOF NETTING, FALSE CEILING, HANGER DOORS, ROOF AND FLOORS IN NORTH SIDE OF RUNWAY IN TECH AREA AT AF STN JODHPUR

Amount

Demolition of cement concrete in ground floors and pavings not exceeding 15 Cm thickness (below/above ground level) including floor finishes complete all as specified & directed by the Engineer-in-Charge.

Dismantling floor, hearth or wall tiling /terrazo including cement mortar bedding but not backing and removing serviceable tiles to store and rubbish off the premises complete all as specified & directed by the Engineer-in-Charge.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided complete all as specified & directed by the Engineer-in-Charge.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work complete all as specified & directed by the Engineer-in-Charge.

Demolition of stone/ boulder masonry, built in cement/ lime mortar including all quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified & directed by the Engineer-in-Charge.

Taking down cement or cement lime plaster work any description from brick or stone wall etc. including raking out of joints, hacking for key, scrubbing down with water etc complete all as specified & directed by the Engineer-in-Charge.

Taking down old Tarfelt of exiting water proofing treatment on RCC roof surfaces including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. including removing debris out site of MD land complete all as specified & directed by the Engineer-in-Charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) not exceeding 1.5 sqm complete all as specified & directed by the Engineer-in-Charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) exceeding 1.5 sqm but not exceeding 4 sqm each complete all as specified & directed by the Engineer-in-Charge.

Taking down shutters exc 1 sqm but not exceeding 2 sqm each complete all as specified & directed by the Engineer-in-Charge.

Taking up or down steel tubing of 15 mm bore pipe and connection including cleaning for re-fixing or removal to store complete all as specified & directed by the Engineer-in-Charge.

Taking up or down steel tubing of 20 mm bore pipe and connection including cleaning for re-fixing or removal to store complete all as specified & directed by the Engineer-in-Charge.

Dismantling old unservicable water tanks of capacity exceeding 250 ltrs but not exceeding 500 ltrs complete all as specified & directed by the Engineer-in-Charge.

Taking down CI/PVC pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., (measured overall as fixed along the centre line over fittings and accessories) complete all as specified & directed by the Engineer-in-Charge.

Material & labour for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) as in sub base etc complete all as specified & directed by the Engineer-in-Charge.

Material & labour for 25mm thick PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in levelling course finished even and fair for laying floor finishes etc complete all as specified & directed by the Engineer-in-Charge.

Material & labour for screed bed/ bedding layer of 15mm thick in cement mortar 1:4 for laying floor finishes etc, complete all as specified & directed by the Engineer-in-Charge.

Material & labour for rendering 15mm thick on stone masonry surfaces or surface other than fair face of brickwork surfaces in cement mortar 1:4, surface finished fair and even, as in backing coat etc complete all specified and directed

Material & labour for rendering 15mm thick on fair faces of brick work or concrete surfaces surfaces in CM 1:4 ,surface finished fair and even as in backing coat etc complete all specified and directed

Material & labour for 8 to10 mm thick Non-skid GVT (Glazed vitrified tiles) coloured (square/rectangular) of size not less than 300mm x 300mm as in floors etc including set, jointed in cement slurry and pointed in white or coloured cement to match the colour/ shades of tiles complete all specified and directed

Material & labour for 8 to10 mm GVT (Glazed vitrified tile ) tiles coloured of approved design pattern of size not less than 300mmx600mm on vertical surfaces including set, jointed in neat grey cement slurry and pointed in white or colour cement to match the shade of the tiles complete all as specified and directed

Material & labour for 10 to 12 mm thick vitrified unglazed and unpolished, scratch resistant, matt finished coloured tiles (square/rectangular) of size not less than 300mm x 300mm as in parking /hardstanding etc including set, jointed in cement slurry and pointed in white or coloured cement to match the colour/ shades of tiles complete all specified and directed

Material & labour for cement concrete work in hard-standing of flexural strength 40 kg/per square centimetre in field using 400 kg of cement per cubic metre, thickness of concrete 25 cm or less complete all specified and directed

Material & labour for 50mm thick PCC 1:2:4 Type B-1 using 20mm graded stone aggregate as in flooring including finishing concrete surfaces even and smooth without using extra cement complete all as specified & directed by the Engineer-in-Charge.

Material & labour for 75 mm thick PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in plinth protection, surface finished even and smooth without using extra cement, laid in panels not exceeding 3 metre long and joints shall be filled with the mixture of bitumen and sand in ratio (1:3) by weight, complete all as specified & directed by the Engineer-in-Charge.

Material & labour for squared rubble walling, Jodhpur type brought upto courses well bonded bedded & solidly hearted built in CM 1:6 complete all as specified & directed by the Engineer-in-Charge.

Ditto all as per item No-26 above but except stone

Material & labour for rendering 15mm thick in cement mortar 1:6 on stone masonry surfaces or surface other than fair face of brickwork of walls including finishing even and smooth surfaces without using extra cement complete all as specified & directed by the Engineer-in-Charge. (Internal plaster)

Material & labour for rendering 15mm thick in cement mortar 1:4 with WPC on stone masonry surfaces or surface other than fair face of brickwork, including finishing even and smooth surfaces without using extra cement complete all as specified & directed by the Engineer-in-Charge. (external plaster) Note:- WPC shall be measured and paid seperately in respective item of BOQ.

Material & labour for rendering 10mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces on ceiling including finishing even and smooth surfaces without using extra cement complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing approved colour powder Coated (minimum thickness of powder coating 50 micron) aluminium frame for doors, window, ventilator with one or more rebates or aluminum section of two or more tracks incase sliding windows including jointing cleat for fixing complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing approved colour powder coated (minimum thickness of powder coating 50 micron) window and ventilator shutters, sliding type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, powder coating aluminium snap beading ,screws etc & including fixed in position star locks, ,rollers for sliding, complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing approved colour aluminium anodised powder coated (minimum thickness of powder coating 50 micron) door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc. complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing 5.5 mm thick sheet glass, ordinary quality in square exceeding 0.50 sqm in each pane complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing 5 mm thick plain colour PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining, Insulated PVC Wall Lining, and Solid PVC Partitions inclusive of Solvent Cement and fixing at site complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing 4 mm thick sheet glass, ordinary quality in square exceeding 0.50 sqm in each pane complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing factory made Solid PVC door frame of size 50 mm x 90 mm including polishing to door shutter to matching complete all as specified and directed by the Engineer-in-Charge.

Supply & fixing Factory Made Solid PVC Moulded Flush Door Shutter with wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm Plain colour PVC Sheet on back face, supplying & fixing in frame at site as per specification complete all as specified and directed.

Supply & fixing Butt hinges medium weight, cold rolled mild steel, of size 125mm long complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing stainless steel barrel tower bolt 150 mm long complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing stainless steel barrel tower bolt 200 mm long complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing stainless steel handle 150 mm long complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing stainless steel handle 200 mm long complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing stainless steel, sliding door bolt with hasp, staple (bolt type) of size 300mm length and fixing clips of sheet and bolts complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing for floor door stopper of stainless stee with hard drawn steel spring over all length of cover plate 150 mm complete all as specified & directed by the Engineer-in-Charge.

Material & labour for taking down shutter exc 1 sqm but not exc 2.00 sqm including easing & adjusting and refixing in same opening with same hardware etc complete all as specified & directed by the Engineer-in-Charge.

Material & labour for preparing plastered or un-plastered new surface and applying three coats of white wash on ceiling surface complete all as specified & directed by the Engineer-in-Charge.

Material & labour for prepration of new plastered surface of walls and applying two coats of white cement based wall care putty finished even and smooth with sand paper and apply two coats of oil emulsion distemper over a coat of alkali resistant primer etc complete all as specified & directed by the Engineer-in-Charge.

Material & labour for preparation of new plaster surfaces of wall and applying two coats of exterior weather proof water based emulsion paint over a coat of primer of same make on walls complete all as specified & directed by the Engineer-in-Charge.

Material & labour for cutting chases for concealed water tubing and making good in CM 1:3 on Stone/Brick wall cutting n.exc 10 Cm in girth complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing 15 mm bore, medium grade, galvanised iron pipe, with all fittings & fixed complete to walls & ceiling or laid in floor complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing 20 mm bore, medium grade, galvanised iron pipe, with all fittings & fixed complete to walls & ceiling or laid in floor complete all as specified & directed by the Engineer-in-Charge.

Refixing of 15mm bore old steel tubing & connection in new or old position (walls ceilings floors etc) complete all as specified & directed by the Engineer-in-Charge.

Refixing of 20mm bore old steel tubing & connection in new or old position (walls ceilings floors etc) complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing in repair two way brass chromium plated fancy type bib cock 15mm bore complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing in repair of brass Chromium plates angle Stop valves of 15mm bore screwed for 15mm bore iron pipe or union complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing in repair brass chromium plated handspray with flxible pipe length not less than 1.00 meter (minimum) fixed for EWC/IWC suitable for 15mm bore pipe complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing in repair of bib tap standard of PTMT any colour high pressure screwed for iron pipe & fixed dia and minimum weight 15 mm- 90gm/each complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing in repair of PVC connection 15mm size with PTMT nuts of length 450mm, complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing in repair EWC seat cover PVC white colour including all fitting arrangements complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing in repair vitreous china wash down water closet pan (pedestal pattern) white and trap including connection to drain flush pipe and anti syphonage pipe complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing in repair of vitreous china water closet (squatt pattern) complete incluing provision of lime concrete bedding fixed in repair of orissa pattern size 580x440mm, white, with and including foot rest (excluding flushing cistern & flush pipe) complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing in repair PVC valveless syphonic action type flushing cistern low level 10ltrs capacity white, fixed with new MS brackets complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing in repair of vitreous china WHB white flat back size 550mmx400mm fixed with and including new MS brackets excluding taps waste china & plug including bracket etc complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing in repair CP waste pipe 32 mm dia with long shank and fly nuts etc for wash basins complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing in repair PVC Flexible waste pipe 32 mm dia with socket for steel sink upto floor level and length not less than 0.60 metre complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing rotational moulded polyethylene water storage tank of capacity 500 litre (Cylindrical vertical with closed top), triple layer construction, white coloured, ISI marked, hoisted & fixed in position including GI light grade 20 mm dia, over flow pipe 450mm long and 20 mm dia waste pipe 600mm long with all fitting etc. of 20 mm dia complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing in repair for 20 mm bore of Ball valve high pressure of PTMT with epoxy coated aluminum rod & high density plastic ball screwed for iron pipe (wt not less then for 20mm-210grms) complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing in repair Gun-metal, globe or gate valves of 20mm bore with half turn lever arm /iron wheel head, screwed both ends for iron pipe complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing 110 mm bore PVC (SWR) single socketed in any length with rubber ring joints fixed to walls with clamps complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing PVC (SWR) bend any radius of 110 mm bore complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal with access door complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing 110 mm bore PVC (SWR) couplers complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing 110mm bore PVC (SWR) vent cowl complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing 75 mm bore PVC (SWR) bend any radius with access door complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing 75 mm bore PVC (SWR) couplers any radius with access door complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing in repair PVC (SWR) floor trap of 75 mm outlet,plain with grating including jointing with solvent cement complete all as specified & directed by the Engineer-in-Charge.

Material & labour for PVC (SWR) gully trap 125/110 mm,setting and jointing with solvent cement complete all as specified & directed by the Engineer-in-Charge.

Cleaning of roof slab/chajja with sweeping with brooms, removing all depositions /mud/vegitation and applying chemical treatment with GLYPHOSATE 41% as per manufacturer's instruction etc and removing the spoil to a distance not exceeding 50 mtr complete all as specified & directed by the Engineer-in-Charge.

Material & labour for brushing neat cement slurry @3 Kg of cement per Square metre of surfaces complete all as specified & directed by the Engineer-in-Charge.

Material & labour for PCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in roof padding with and including waterproofing compound at 3 % by weight of cement, finished even and fair on roof/ chajjas etc complete all as specified & directed by the Engineer-in-Charge.

Material & labour for Cutting out cracks to V-section in existing roofs or terracing, cleaning out, wetting, grouting with cement and sand slurry 1:3 with water proofing compound as per manufacture instruction complete all as specified & directed by the Engineer-in-Charge.

Material & labour for Preparation of concrete surface for applying bituminous primer (conforming to IS : 3384-1965 ) @ 0.40 Kg/Sqm complete all as specified & directed by the Engineer-in-Charge.

Material & labour for applying evenly a tack coat of industrial bitumen grade of 85/25 at the rate of 1.2 kg per sqm including cleaning surfaces complete all as specified & directed by the Engineer-in-Charge. Note:- (Ist coat for bonding material below membrane and IInd coat on top of membrane. Each coat will be paid seperately)

Material & labour for APP modified polymeric membrane ,centre core of 100 micron HMHDPE, Outer film 20 micron each , thickness 3.00mm , having weight not less than 3.00 Kg / Sqm laid on primed surface by forced applicationand finally finished with aluminium paint @ 0.20 Ltr per sqm complete all as specified & directed by the Engineer-in-Charge.

Material & labour for cement concrete 1: 2:4 Type B-1 (using 20mm graded stone aggregate) in roof kerbs or mud stops,/ benching, rounded or chamfered on edges complete all as specified & directed by the Engineer-in-Charge.

Material & labour for 10 mm thick rendering in Cement Mortar 1:4 with and including water proofing compound at 3% by weight of cement WPC on concrete surfaces while concrete surface is green on roof, finishing even and smooth without using extra cement complete all as specified & directed by the Engineer-in-Charge.

Cleaning and removing all scale and dirt etc from over head water tanks and from mouths of circulating pipe etc including dismantling & refixing at same or other place for capacity exceeding 250 Ltrs but not exceeding 500 Ltrs complete all as specified & directed by the Engineer-in-Charge.

Taking down and re-fixing of old aluminum door shutters in same opening with necessary required repairs and fittings including glass rubber bedding and glazing clips, area exc 2.00 sqm but nexc 4.00 sqm each complete all as specified & directed by the Engineer-in-Charge. Note:- Glass pan and wire gauge will be measured and paid separately.

Taking down and re-fixing of old aluminum window in same opening with necessary required repairs and fittings including galss rubber bedding door frame rubber bedding and glazing clips, area n.exc 2.00 sqm each complete all as specified & directed by the Engineer-in-Charge. Note:- Glass pan and wire gauge will be measured and paid separately.

Material & labour for sweeping, cleaning and washing down with water to remove dust, etc old tarfelt of exiting water proofing treatment on roof surfaces and applying a coat of elastomeric polyurethane liquid membrane as per manufacturer instruction to stop leakage /seepage from roof/wall complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing in repair yen iron body capsule type pattern door closer standard size in multicolour, including roller & roller plate complete of mild steel complete all as specified & directed by the Engineer-in-Charge.

Supply & fixing in repair 18mm thick solid UPVC ply of 1st quality of one side prelaminated of approved colour and one side white colour fixed with screwes, solvent cement /adhesive to make cabinate and cup board shutters complete all as specified and directed.

Supply & fixing in repair 18mm thick UPVC coated ply of grade 1 quality of both side white colour fixed with screwes, solvent cement /adhesive to making of furniture /wall panlling/ CBs shutters etc. complete all as specified and directed

Supply & fixing in repair 12mm thick UPVC coated ply of grade 1 quality of both side white colour fixed with screwes, solvent cement/adhesive to making of furniture /wall panelling/ CBs shutters etc. complete all as specified and directed

Supply & fixing in repair sliding telescopic channel high grade mild steel, bright finish or electrogalvanised of size 20" as per approved sample omplete all as specified and directed

Supply & fixing Magnet catch for CB/ cabinet shutters as per approved sample complete all as specified and directed.

Supply & fixing in repair Continuous (piano) hinges, mild steel, bright finish or electrogalvanised for 30mm width of flaps (when open) complete all as specified and directed.

Supply & fixing in repair Stainless steel barrel tower bolt of 100mm size as per approved sample complete all as specified and directed

Material & labour for providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed

Supply & fixing in repair 12 to 15 mm thick mineral fiber ceiling board with 0.75 NRC sound absorbtion, 85 %, light reflectance , RH 95%humidity resistance , of size 600x600mm fixed with and including galvinsed steel frame complete all as specified and directed

Taking down existing unserviceable, broken, rusted steel rolling shutter of any size and type and Supply & fixing factory made Steel rolling shutters with laths of thickness 1 mm, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type complete all as specified and directed. Note:- A BOO shall be nominated by GE to acertain the quantity of new rolling shutter and collapsible steel gates replaced at site. BOO will verify the quanity at site and submit their findings to GE duly signed by BOO.

Taking down carefully hood and steel rolling shutter of size not exceeding 15 sqm and replacement of unserviceable/defective parts and refixing in the same opening after cleaning of guide rails, laths, top cover by kerosene and proper greasing, oiling, replacement of rusted nut bolts etc, removing of bend, alignment etc to make the system smooth functional & making good the disturbed surface all as specified & directed by Engineer-in-Charge. Note :- (i) The unserviceable parts to be replaced shall be measured and paid for separately as "Supply only". (ii) Quoted rate shall be inclusive of providing missing nuts bolts, greasing, oiling, denting, tension to spring etc.

Taking down carefully hood and steel rolling shutter of size exceeding 15 Sqm but not exceeding 25 sqm and replacement of unserviceable/defective parts and refixing in the same opening after cleaning of guide rails, laths, top cover by kerosene and proper greasing, oiling, replacement of rusted nut bolts etc, removing of bend, alignment etc to make the system smooth functional & making good the disturbed surface all as specified & directed by Engineer-in-Charge. Note :- (i) The unserviceable parts to be replaced shall be measured and paid for separately as "Supply only". (ii) Quoted rate shall be inclusive of providing missing nuts bolts, greasing, oiling, denting, tension to spring etc.

Supply only flat spring suitable for rolling shutter of area not exceeding 15 sqm each complete all as specified and directed.

Supply only flat spring suitable for rolling shutter of area exceeding 15 Sqm but not exceeding 25 sqm each complete all as specified and directed.

Supply only ball bearing 50 mm dia complete all as specified and directed. Make SKF/NBC

Supply only ball bearing 100 mm dia complete all as specified and directed. Make SKF/NBC

Supply only MS sheet hood cover of 1.00mm thick bent to shape match with existing brackets including stiffners of MS angles/flat complete all as specified and directed.

Supply only MS tubing 50mm bore medium grade with necessary holes for shaft complte all as specified and directed.

Supply only MS tubing 40mm bore medium grade with necessary holes for shaft complete all as specified and directed.

Supply only gear box of steel rolling shutter Including handle rack & pinion system, bearing etc of rolling shuter size 5 Sqm each complete all as specified & directed by Engineer-in-Charge.

Material & labour for taking down carefully gear box for repairs including rack & pinion system bearing including welding teeth and grinding, greasing and refixing etc for rolling shutter size 5 Sqm and above but not exceeding 25 Sqm each to make it serviceable Including minor repair complete all as specified & directed by Engineer-in-Charge.

Taking down existing unserviceable, broken, rusted collapsible steel gates and Supply & fixing collapsible steel gates, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete all as specified & directed by the Engineer-in-Charge. Note:- A BOO shall be nominated by GE to acertain the quantity of new rolling shutter and collapsible steel gates replaced at site. BOO will verify the quanity at site and submit their findings to GE duly signed by BOO.

Material & labour for repairs to collapsible steel gate of size not exceeding 10 sqm, including removing and replacing worn out minor parts such as rivets, roller wheels etc. straightening of vertical channels and cleaning of rust including greasing and re-fixing the same in position complete all as specified and directed. Note: (i) The unserviceable parts to be replaced shall be measured and paid for spearately as " Supply only". (ii) Quoted rate shall be inclusive of providing missing nuts, bolts, greasing , oiling etc.

Material & labour for repairs to collapsible steel gate of size exceeding 10 sqm but not exceeding 15 sqm including removing and replacing worn out minor parts such as rivets, roller wheels etc. straightening of vertical channels and cleaning of rust including greasing and re-fixing the same in position complete all as specified and directed. Note: (i) The unserviceable parts to be replaced shall be measured and paid for spearately as " Supply only". (ii) Quoted rate shall be inclusive of providing missing nuts, bolts, greasing , oiling etc.

Material & labour for cutting holes in stone walls built in cement mortar for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B1 as required, depth of embedded portion of hold fasts or lugs exceeding One brick but not exceeding two bricks from the face of the jamb in to the wall complete all as specified & directed by the Engineer-in-Charge.

Supply only guide channel of 75mm for rolling shutters including hold fasts welded to channel complete all as specified and directed.

Supply only pivoted flat bar 20x5 mm fixed with rivets in required position as in collapsible gates complete all as specified and directed.

Material & labour for cleaning and greasing the top and bottom guide rails of MS sliding door complete all as specified and directed.

Material & labour for running welding in repairs, thickness of metal to be welded not exceeding 6mm complete all as specified & directed.

All as per item No-- 124-- above but thickenss of metal to be welded exceeding 6 mm but not exceeding 9mm.

Material & labour for hacking out oud broken glass (any thicknes, size, qulity or description) from metal frame glazed with putty including punching or drilling out old galzing pin/spring, clips and providing new ones and providing rough cast wired galss, 6.4mm thick and glazing with oil putty in square n.exc. 0.5 sqm in each pane complete all as specified & directed.

Material & labour for preparation of new or previously untreated steel surfaces of any description, over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed.

Material & labour for preparation of old painted steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying once coat of synthetic enamel paint complete all as specified & directed.

Dismantling of old unserviceable, rusted, broken (corrugated/semi corrugated, etc.) CGI/AC/ Fibre glass sheets in ridge and roof coverings complete all as specified & directed.

Supply & fix 2 mm thick fibre glass reinforced translucent corrugated sheeting with two corrugation side lap, fixed with L- or J- type or cranked hook bolts and washers, in roofs, walls etc. complete all as specified and as directed by the Engr-in - Charge.

Material & labour for 6 mm thick asbestos cement, corrugated or semi corrugated sheets in roofs, walls etc. fixed with L- type or J-type or cranked hook bolts, in roofs, walls etc. complete all as specified and as directed by the Engr-in - Charge.

Supply & fix Pre-painted galvalume GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by Engineer-in-Charge.

Supply & fix Pre-painted galvalume GI based plane steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding tow wall, fixed with self tapping screws complete all as specified and as directed by Engineer-in-Charge.

Supply only MS crank handle 250mm long suitable for operating rolling shutter complete all as specified and directed.

Material & labour for locking device cleat of rolling shutter complete all as specified and directed.

Material & labour in replacement of 1.00mm thick MS laths of continuous single piece secton without any welded joint of steel rolling shutter, the lath section shall be rolled so as to have inter locking coils at both edges & deep corrugations at the center with average depth of not less than 12mm & each alternate lath section shall be fitted with malleable cast iron or mild steel clips securrely riveted at either ends complete including painting with two coats of synthetic enamel paint over one coat of red oxide primer all as directed by Engineer-in-Charge.

Material & labour for oiling and greasing to pullers of each steel sliding hanger door shutter (each panel) cleaning with standard thinner such as carbon tetra chloride/Benzene and making it smooth functioning to reduce the friction of door complete all as specifed and directed.

Supply & fixing in repairs MS pulley 25 cm dia with bearing shaft, nuts including making necessary arrangement for taking down old pulley at the bottom of sliding hanger door shutter complete all as specifed and directed.

All as per item No 138 above but 14 cm dia pulley/roller at the top of shutter.

Supply & fixing in repairs bearing for 14cm/25cm dia pulley, rollers including welding replacement of old nuts/bolts etc complete for smooth functioning in perfect alignmnet all as directed by Engineer-in-Charge.

Supply & fixing in repairs bearing for shaft of rolling shutter including welding replacement of old nuts/bolts etc complete for smooth functioning in perfect alignment all as directed by Engineer-in-Charge.

Supply & fixing in repairs purpose made locking arrangement for hanger door shuters 600 to 900mm long including welding, drilling, cutting with nut and bolt all as directed by Engineer-in-Charge.

Material & labour in replacement of pintle hinge, locking device cleat, hold fast for steel gate and door including removing of bend alignment, fixing and welding work for smooth functioning complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and as directed by Engineer-in-Charge.

Supply & fixing rolled milld steel of grade Fe-290 (Grade E-165) in framed work as in doors or gates of angle or other section with gussets plates, rails braces, etc. complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing complete all as specified and directed.

Supply & fix in repair wire netting of stainless steel wire 0.91 mm dia and size of mesh 20 mm appartue fixed with tinned tacks of stainless steel wire staples complete all as specified and as directed.

Supply & fix in repair UV resistance Polythene bird netting (Suraksha plus) made out of 1mm dia or twine manufactured by Netlon India Ltd to existing truss and purline to hanger of mesh size 20mm x 20mm including fixing with accessories/fixing material required such as clamps, nuts washers etc as required at site complete all as specified and as directed by Engineer-in-Charge.

Racking out joints/pointing to squared rubble masonry, coursed or uncourased built in cement or cement lime mortar complete all as specified and as directed by Engineer-in-Charge.

Material & labour for keyed pointing to squared rubble stone masonry, coursed or uncoursed in CM 1 :4 complete all as specified and as directed by Engineer-in-Charge.

Material & labour for preparation of newly plastered or unplastered surfaces of walls and applying three coats of white wash complete all as specified and as directed by Engineer-in-Charge.

Material & labour for preparation of old plastered or unplastered surfaces of walls and applying one coat of white wash complete all as specified and as directed by Engineer-in-Charge.

Material & labour for preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint, white or tinted complete all as specified and as directed by Engineer-in-Charge.

BAGHELA CONSTRUCTION

RISING ELECTRICALS

VIKAS CONSTRUCTION CO.

M/s. Dhananjay Construction