DMF Grant

Drilling of 165mm dia Bore well by down the hole hammer drilling to a finished dia of 165mm dia in all formations suitable for down the hole hammer drilling such as medium hard rock formation to hard rock formation all consolidated formation etc., and drilling in over burden to dia not less than 200mm etc., and reaming the bore well to suit insertion of suitable casing pipe etc., including insertion of casing pipe with couplings, caps any other relevant materials upto required depth as directed by the department including transportation of drilling rigs and supporting vehicle and including bore development (Flushing of Bore well at an average pressure of 150 PSI) conducting yield test, consumables charges, crew charges required in fixation of pipe assembly completely done to the satisfaction of the department and including all labour charges, all taxes and EXCLUDING GST, but excluding the cost of casing pipe, couplings, cap etc., The entire work should be carried out as per IS-2800 Part-I & II 1979 and amended from time to time up to 90 Mts depth.

Cost and supply of 180mm dia PVC blue Casing Pipe

Slotting chages for 180mm dia PVC Casing Pipe

Supply and fixing of 180mm dia PVC Bore Cap

Geologist charges for selection of bore well site

Supply and Transportation of 10.00HP, 5-10 Stage, 5star rated submersible motor pumpset, confirming to IS 8034 and motor confirming to IS 9283 with water proof winding, Pump shall be suitable for various delivery head and discharge with stainless steel shaft.Motor suitable for working on 415V ± 10% , Three Phase 50 Hz AC supply, etc., complete for 6" Bore well. Makes: Kirloskar / Crompton / Texmo / CRI / KSB/Lubi/ PSG/AryenVarsha

Supply and delivery of 75/65 mm UPVC pipe with standing up to 20 Kgs / CM2 upto 200 Mts for submersible motors with both ends square threaded, with rubber 'O' rings with smooth inner surface which can take the minimum load of 2100 to 4000 Kgs weights. Makes : Ashirvad / Finolex / Waterflo /Sudhakar as per ELEC-5.4.21

Supply and delivery of heavy duty couplings 75/65 mm UPVC pipe (27 Kgs / CM 2 ) capable of with standing up to 27 Kgs / CM2 above 200 mts and upto 300 mts as per ELEC-5.4.22 conveyance of all materials and all labour charges etc., complete.,

Supply of 3 Core 2.50 Sqmm Flat Copper cable of ISI for Submersible Motors confirming to IS:694:1990. Makes: Finolex / RR Kabel/ Polycab / Havells / EI/ Gloster/ Goldmedal/ GM

Fabrication , transportation and supply of wall mounted control panel board of size 600x600x250mm made of 18 SWG CRCA sheet steel enclosure, 14 SWG mounting plate for cable entry fabricated , painted with two coats of Red oxide primer and two coats of Grey paint, lock and key arrangements two side lovures with weld mesh inside etc., complete consisting of the following equipment with all internal wiring using L&T / Finolex copper FRLS cables of suitable size and capacity and cable clamp etc., complete., for 3 phase motor pump sets. (1) Voltmeter ; 0-500 V 96x96mm size Makes: L&T / C&S / SALZAR / HPL/ AEI / Meco / Rishab - 1No (2) 0 to 20 Amps / 0- 50 Amps Ammeter 96x96mm size).Makes: L&T / C&S / SALZAR / HPL/ AEI / Meco / Rishab-1No. (3) Single phase preventor of suitable range Makes: L&T / Minilec/ Powertec. - 1No. (4) 32 A TP, 10KA MCB. Makes: Legrand / Schneider / - 1No (5) Indication lamps (R-Y-B) with switch control - 1set (6) Voltmeter & Ammeter selector switch - 2 Nos of Supply and fixing of ISI Mark suitable capacitor Makes: L&T / Siemens / Schneider / Epcos/ Havells for 10.00 HP with DOL Starter of Make C&S.Crompton / L&T / KSP/ Siemens/ BCH.

Supplying and fixing of 50 mm dia MS Clamp Sets including rubber washers, bolts and nuts cost and conveyance of all materials and all labour charges etc., complete.,

Labour charges for erection of 10.00 HP three phase submersible pumpsets (Bore well type) including pipe connection for suction and delivery and all labour charges etc., complete.,

Supply, delivery and fixing of 65 mm Nominal Bore GI pipe Medium Grade properties & weight as per IS 1239 with GI fittings such as elbows tees couplings, nipples, plugs excluding excavation for trenches and refilling the trenches complete except for GI bends union and GI connectors with checkout and socket Tata or Zenith make or equivalent.

Earth work excavation in BC soils, red earth and ordinary gravelly soils for pipe line trench of size 0.70 x 1.00 Mts using 2/3 Quanity with machinery and 1/3 quantity with manual including laying and jointing of 90 mm dia PVC 6 Kgs/Sqcms true to alignment and testing the pipe line with hydralic field test pressure with water minimum lead of 500mts including refilling the trench with excavated earth including cost of pipes and all labour charges etc., complete., but excluding taxes on PVC pipes etc., complete.,