Special repair of control room including painting, replacement of Railings at pitching area left bank and right bank of the reservoir and construction of ladies toilet and a Guard Room at Ichari Dam

Amount

CIVIL WORKS

Earth work in excavation by mechanical means (Hydraulic Excavator)/ manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Supplying and filling in plinth with sand under floors including, watering, ramming consolidating and dressing complete.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to the full depth of the hole : With Chlorpyriphos/Lindane E.C. 20% with 1 concentration

Coursed rubble masonry (first sort) Cement mortar 1:6 (1 cement : 6 coarse sand) with hard stone in foundation and plinth

Random rubble masonry Cement mortar 1:6 (1 cement : 6 coarse sand) with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level. 1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mmnnominal size) .

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers,abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for all heights for Columns, Pillars, Piers, Abutments, Posts and Struts.

Centring and shuttering including strutting, propping etc. and removal of form for all heights for Suspended floors, roofs, landings, balconies and sq.m access platform.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in Cement mortar 1:6 (1 cement: 6 coarse sand).

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand).

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in Cement mortar 1:4 (1 cement :4 coarse sand).

Steel reinforcement for R.C.C. work including straightening, cutting, bending,placing in position and binding all complete upto plinth level using Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

12 mm cement plaster of mix 1:4 (1 cement : 4 fine sand) .

Removing dry & oil bound distemper , water proofing cement paint & the like by scrapping , sand papering & prepairing the surface smooth including necessary repairs to scratches etc. Complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade New work (two or more coats) over and including priming coat with cement primer.

Distempering with oil bound washable distemper Old work (one or more coats) of approved brand and manufacture to give an even shade :

Finishing walls with water proofing cement paint of required shade : Old work (one or more coats @ 2.20 kg/10 sqm) complete.

Finishing walls with textured exterior paint of required shade : Old work (Two or more coats on existing cement paint surface applied @ 3.28 ltr/10 sqm.

Finishing walls with textured exterior paint of required shade : Old work (One or more coats) applied @ 1.82 ltr/10 sqm.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work.

Lettering with black Japan paint of approved brand and manufacture.

Painting with black anti-corrosive bitumastic paint of approved brand and manufacture to give an even shade : One or more coats on old work.

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc complete.

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete with 40mm thick with 20mm nominal size stone aggregate.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Granite of any colour and shade with Area of slab over 0.50 sqm. CPWD DSR 2019 8.2.2.2

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer in- Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

(a) 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

(b) 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing flat pressed 3 layer particle board medium density exterior grade (Grade I) or graded wood particle board IS : 3087 marked to frame, backing or studding with screws etc. complete (Frames, backing or studding to be paid separately).

(a) 12 mm thick.

(b) 18 mm thick.

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. Pre-laminated particle board of 12 mm thickness with decorative lamination on both sides, Grade I, Type II, IS:12823 marked. (CPWD DSR 2019 Code No.-9.7.5.3)

Providing and fixing chromium plated brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete. CPWD DSR 2019 9.88

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion (a) Powder coated aluminium (minimum thickness of powder coating 50 micron) CPWD DSR 2019 21.1.1.2

For fixed portion (b) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15) CPWD DSR 2019 21.1.1.1

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) (a) Powder coated aluminium (minimum thickness of powder coating 50 micron) CPWD DSR 2019 21.1.2.2

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by ngineerin-charge. The sheet shall be fixed using self drilling / self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

S/Replacement of the following types of oxidized iron fitting of approved quality

Providing and fixing ISI marked oxidised M.S.sliding door bolts with nuts and screws etc 300x16mm .(CPWD DSR 2019,Building Works, Code No- 9.62.1)

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc.150x10 mm .(CPWD DSR 2019,Building Works, Code No- 9.63.3)

Providing and fixing ISI marked oxidised M.S. pressed butt hinges with necessary screws etc. 100x58x1.90 mm (CPWD DSR 2019,Building Works, Code No- 9.57.2)

Providing and fixing ISI marked oxidised M.S.handles conforming to IS:4992 with necessary screws etc. 100 mm . (CPWD DSR 2014,Building Works, Code No- 9.66.2)

Providing and fixing ISI marked oxidised M.S. single acting spring hinges 150mm (CPWD DSR 2019,Building Works, Code No- 9.60.1)

Attending minor type of repair for full day by engaging and supplying one suitable carpenter/Mason/Plumber for carrying simple type of repairing of all work including all T&P etc. complete but excluding cost of material.NSI

Attending minor type work like cleaning and other misc work by engaging labour for full day including all T&P etc. complete.NSI

Removal of of debris /waste material/ any other material / rubbish by full load tractor trolly as desired by the Engineer-in- charge & safe disposal of the same out side the nigam area including cost of all labour, T&P etc required for proper loading/unloading and disposal of waste or any other material required for the proper completion of the work. (NSI)

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm CPWD DSR 2019 13.45.1

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture CPWD DSR 2019 13.48.2

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture CPWD DSR 2019 13.48.3

Distempering with 1st quality acrylic washable distemper (ready made) One or more coats on old work of approved manufacturer and of required shade and colour complete. as per manufacturer's specification. CPWD 2016 14.63.1

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade Two or more coats on new work ( CPWD DSR 2019 13.60.1)

Renewing glass panes, with putty and nails wherever necessary Float glass panes of thickness 4 mm . (CPWD DSR 2019,Building Works, Code No- 14.5.1)

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer using flats 30x6mm for diagonal braces and central cross piece. CPWD DSR 2019 10.5.2

Providing second class teak wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

Hire charges of welding machine with single phase with welder, helper and electrodes etc. for repair and welding of gates, door, window etc. for 8 hrs. in a day complete with all material labour, T&P etc. required for proper completion of work.

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.. CPWD DSR 2019 10.18

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing PVC false ceiling of approved quality with necessary nails etc. complete:

Providing & fixing Single piece-WC (LYS-WHT-0204BS+ZPS-WHT-1027UF) Jaquar make for proper completion of work.

Providing & fixing Counter top Basin Hindware RHAPSODY size 63x50 cm make for proper completion of work.

Providing & fixing Single lever basin mixer without popup waste system with 450 mm long braided hoses (FLR-5001B) Jaquar make for proper completion of work.

Providing & fixing Hand Dryer-smartflow (HDR-WHT-M04A) Jaquar make for proper completion of work.

Providing & fixing Soap Dispenser-Push Button (SDR-WHT-DJ0010F) Jaquar make for proper completion of work.

Providing & fixing Bib cock (Straight line model) (FLR-5047N) Jaquar make for proper completion of work.

Providing & fixing Concealed Stop cock Jaquar make for proper completion of work.

Providing & fixing Bottle Trap (with internal partition) 32 mm size with 250 mm & 190 mm (ALD-769L250x190) Jaquar make for proper completion of work.

Providing & fixing angular stop cock with wall flkange (FLR-5053N) Jaquar make for proper completion of work.

Providing & fixing Click clack waste 32 mm size half Thread with 80 mm Height (ALD-729) Jaquar make for proper completion of work.

Providing & fixing Toilet roll holder with flap (AKP-35753P) Jaquar make for proper completion of work.

Providing & fixing Hand Shower (Health Faucet) with 8mm dia, I meter long flexible tube & wall hook (ALD-573) Jaquar make for proper completion of work.

Providing & fixing Soap Dish holder (AKP-35731P) Jaquar make for proper completion of work.

Providing & fixing Tumbler Holder (AKP-35741P) Jaquar make for proper completion of work.

Providing & fixing Grab Bar (Stainless Steel) 300 mm long (AHS-1501) Jaquar make for proper completion of work.

Providing & fixing Towl Ring Square (AKP-35721P) Jaquar make for proper completion of work.

Providing and fixing PTMT bib cock of approved quality and colour. 15 mm nominal bore, 122mm long, weighing not less than 99 gms.

Providing and fixing 15 mm nominal bore brass stop cock of approved quality

Providing and fixing white vitreous china wash basin including making all connections but excluding the cost of fittings. Flat back wash basin of size 550x400 mm.

Providing & fixing White vitreous china water closet squatting pan (Indian type) along with "S" or "P" trap including dismantling of old WC seat and "S" or "P" trap at site complete with all operations including all necessary materials, labour and disposal of dismantled material i/c malba, all complete as per the direction of Engineer-in charge.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes 75 mm diameter

Providing and fixing 32 mm diameter flexible P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Providing and fixing 15 mm nominal bore, 105mm long, weighing not less than 138gms. PTMT Ball cock of approved quality, colour and make complete with Epoxy coated rod with L.P./ H.P.H.D. plastic ball.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes 110 mm diameter

Providing and fixing PTMT towel rail complete with brackets fixed to woodencleats with CP brass screws with concealed fittings arrangement of approved quality and colour 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 15 mm nominal bore ball valve (brass) of approved quality, High or low pressure, with plastic floats complete.

Providing and fixing 15mm nominal bore C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

Providing and fixing 15 mm dia. nominal bore G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Iinternal work - Exposed on wall

Providing and fixing 15 mm dia. nominal bore G.I. pipes complete with G.I. fittings including trenching and refilling etc. (external work).

Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 15mm nominal bore. C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.

Providing and fixing15 mm nominal bore, 107mm long, weighing not less than 110 grams PTMT pillar cock of approved quality and colour.

Providing and fixing curtain rods of 1.25 mm thick chromium plated brass plate, with two chromium plated brass brackets fixed with C.P. brass screws and wooden plugs, etc., herever necessary complete :

12 mm dia

20 mm dia

25 mm dia

Providing, Stitching, Hanging & Fitting Exclusive, High Quality, Heavy Curtain cloth for Ichari Dam including supply of all materials, labours an T&P etc .required for complection of work

Providing and fixing water purifiers Aquaguard Enhance model RO+UV+UF+TDS Regulator for Ichari Dam

Providing & Fixing of Samsung refrigerator RR20M2Z2XU7 1 Door with Smart Digital Inverter Technology 192l for Ichari Dam

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing factory made uPVC white colour sliding glazed window above 1.50 m in height dimension comprising of uPVC multi-chambered rame with in-built roller track and sash extruded profiles duly reinforcedwith 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads, uPVC extruded interlocks and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle on one side of extreme panel along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) touch lock with hook (if required for wire mesh panel), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately).

Two track two panels sliding window made of (big series)frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 2.50 sqm upto 4.00 sqm.)

Two track four panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 4.00 sqm upto 8.00 sqm).

Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealent shall be paid separately).DSR-20119:-9.147C

Casement door with 3D hinges made of (big series) frame 67 x 64 mm & sash 67 x 110 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door upto 2.00 sqm).DSR-9.147C.1

Casement door with top hung ventilator with 3D and S.S. friction hinges (400 x 19 x 1.9 mm) made of (big series) frame 67 x 64 mm, sash 67 x 110 mm & mullion 67 x 80 mm all having wall thickness of 2.3 ±. 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.(Area of door upto 2.50 sqm) DSR-9.147C.2

Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of equired length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.DSR-2019:-9.147B

Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)-DSR-9.147B.1

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced ith 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.DSR-2019-9.147D

Two track two panels sliding window made of (small series) frame 52 x 44 mm &sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window upto 1.75 sqm)

Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

TTwo track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension . (Area of indow above 1.75 sqm upto 2.50 sqm).

Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing glazing bead of appropriate dimension. (Areaof window above 1.75 sqm).

Three track three panels sliding window made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and Single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm)

Providing and fixing stainless steel (SS-304 grade) friction hinges to the side/top hung uPVC windows, of approved quality, with necessary stainless steel screws etc. as per direction of Engineer-in-charge.DSR-9.148.

Providing and fixing casement handle made of zinc alloyed (white powder coated) for uPVC casement window with necessary screws etc. complete. .

Providing and fixing zinc alloyed (white powder coated) touch lock for uPVC sliding window with necessary screws etc. Complete.

Providing and fixing steel roller for uPVC sliding window with necessary screws etc. complete.

Providing and fixing steel roller for uPVC sliding door with necessary screws etc. complete.

Providing and fixing steel (white power coated) crescent lock for uPVC sliding window/ door with necessary screws etc. complete.

Supply and fixing of PVC Hollow wall Panel sheet and Fitting/installation charge complete in all respect, including supply of all material, labour,T&P etc .Required for proper completion of work. NSI

Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991,in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 24x38 mm of length 3000 mm, cross - T of size 24x32 mm of length 1200 mm and secondary intermediate cross-T of size 24x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.With 15 mm thick tegular edged light weight calcium silicate false ceiling tiles.

ELECTRICAL WORKS

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group B CPWD M 2018 1.10.2

Group C CPWD M 2018 1.8.3

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. CPWD 2018 1.11

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire CPWD 2018 M 1.14.1

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire CPWD 2018 M 1.14.2

2 X 4 sq. mm + 1 X 4 sq. mm earth wire CPWD 2018 M 1.14.3

2 X 6 sq. mm + 1 X 6 sq. mm earth wire CPWD 2018 M 1.14.4

4 X 10 sq. mm + 2 X 6 sq. mm earth wire CPWD 2018 M 1.14.10

Supplying and drawing 2 Pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. CPWD 2018 M 1.18.2

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required. CPWD 2018 M 1.19

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

20 mm CPWD 2018 M 1.21.1

25 mm CPWD 2018 M 1.21.2

Supplying and fixing metal box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc. as required.

100 mm X 100 mm X 60 mm deep CPWD 2018 M 1.22.2

150 mm X 75 mm X 60 mm deep CPWD 2018 M 1.22.3

180 mm X 100 mm X 60 mm deep CPWD 2018 M 1.22.5

Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required

5/6 A switch CPWD 2018 M 1.24.1

15/16 A switch CPWD 2018 M 1.24.3

3 pin 5/6 A socket outlet CPWD 2018 M 1.24.4

6 pin 15/16 A socket outlet CPWD 2018 M 1.24.5

Telephone socket outlet CPWD 2018 M 1.24.6

TV antenna socket outlet CPWD 2018 M 1.24.7

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. CPWD 2018 M 1.25

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required. CPWD 2018 M 1.33

Supplying and fixing stiff pendent with 300 mm long, 20 mm dia X 1.6 mm thick steel conduit, aluminium cast back plate and brass holder complete, including wiring the down rod with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and painting etc. as required. CPWD 2018 M 1.36

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required. CPWD 2018 M 1.38

Supplying and fixing 8 way, Double door, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) CPWD 2018 M 2.3.2

S/F of TPN Double door DB 4 way make Havells.

S/F of 63 A 4 pole MCCB make Havells.

Supplying and fixing Single pole 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. CPWD 2018 M 2.10.1

Supplying and fixing 40 A , double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. CPWD 2018 M 2.12.1

Supplying and fixing 25 A, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. CPWD 2018 M 2.14.1

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required. CPWD 2018 M 5.4

Supplying and fixing 20 A, 240 V, SPN Industrial type socke outlet, with 2 pole and earth, metal enclosed plug top alongwit 20 A, “C” curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required. CPWD 2018 M 2.18

Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required. CPWD 2018 M 5.12

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required. CPWD 2018 M 1.45

S/F of Fan Box.

Supply and Fixing of 63 A alluminium bush baar.

Supply and Fixing of 63 A Chang over Switch.

Supply and laying of 25 Sq.mm. x 3.5 Core alluminium Armoueed cable.

Supply and fixing of 1200 mm size ceiling fan of Havells/Bajaj /Usha/Orient make

Supply and fixing LED Bulb of 15 Watt of Havells/Bajaj/Philips/syska Make

Supply and fixing LED Bulb of 12 Watt of Havells/Bajaj/Philips/syska Make

Supply and fixing LED Bulb of 9 Watt of Havells/Bajaj/Philips/syska Make

Supply and fixing LED Tube Light of 16 Watt of Havells/Bajaj/Philips/syska Make

Supply of exhaust fan (plastic) size 200 mm of Havells/Bajaj/Philips/Orient Make

Supply of water heater of 25 L capacity (Adonia) of Havells make

Supply of oil filled radiator Room heater OFR 13 Pin of Havells make

Supply and fixing LED Light for Roof of Havells/Bajaj/Philips/syska Make

Supply and fixing LED Fancy Light for wall of Havells/Bajaj/Philips/syska Make

Y K Jain Company