ADDN/ALTN TO BLDG NO P-74 (SMC) AND PROVN OF DRAIN AT BLDG NO-163 AND MAIN GATE AT AF STN WADSAR UNDER GE (AF) CHILODA

Amount

M&L for complete removal of existing unserviceable water proofing treatment from top of roof and canopies/chajjas of building including removal of debris out side MD land complete all as specified and directed.

Demolition of cement concrete (un-reinforced) of any description (including plastering,leeping etc) in any position not otherwise specifically provided for not exc 15 cm thick complete all as specified and directed.

M&L for providing cement concrete type B-0, 1:2:4 using 12.50 mm graded aggregate laid to slope 1:30 in padding for WPT over roof slab complete all as specified and directed by Engineer-in-Charge.

M&L for rendering 10mm thick in CM 1:4, mixed with WPC @3% by weight of cement on fair faces of concrete surfaces without using extra cement as in roof complete all as specified and directed. Note:- WPC shall be measured & paid separately.

M&L for preparing clean and dried plastered surface and applying a coat of oil based bitumen primer conforming to IS 3384-1986 @ 0.30 litrs/sqm and then laying APP polymer modified membrane, 3mm thick with non woven polyster reinforced membrane (3.50 kg/sqm) having thermal insulation with white mineral gravel finish on upper side of membrane and laid by torch application method to the entire surface complete all as specified and directed by Engineer in Charge.

Supply only Integral waterproofing compound

M&L removing the tank over roof and re-fixing in the same position including cleaning complete all as specified and directed.

Dismantling of floor hearth or wall tilling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for 15 mm thick screed bed or bedding layer of morter for laying floor finishes CM 1:6.complete all as specified and directed

M&L for Endura glazed tiles 10 mm thick light/dark shade (square) area of each tiles 300 mm x 300 mm, in floor etc.set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

M&L for Virified Ceramic tiles light shade 10 mm thick (square/rectangular) polished, area of each tiles exceeding 0.42 sqmbut not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed inwhite or coloured cement to match complete all as specified and directed.

All as per item No 11 here in before but dark shed as in skirting complete all as specified and directed.

M&L glazed ceramic coloured digital tiles 450x300mm x 7mm thick in vertical surface etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including backing coat of CM 1:4 10mm thick etc complete all as specified and as directed..

Taking down cement or cement lime plaster any description on brick or stone wall/ celling including raking out joint , haking for key scrubing with water etc complete all as specified and directed

M&L for rendering 15 mm thick on fair faces of concrete or block masonary CM 1:6 finished even and smooth (without using extra cement) in internal surface of wall complete all as specified and directed

All as per item No 15 here in before but 10 mm thick CM 1:6 and setting coat 5mm thick CM 1:4 mixed with WPC in external surface of wall including scaffolding complete all as specified and directed . Note:- WPC measured and paid in revalent item of this schedule.

All as per item No 16 here in before but 5 mm thick in ceiling surfaces in CM 1:4 complete all as specified and directed

Material & Labour for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

M&L for preparation of new plastered surface of wall and applying two coats of distemper oil emulsion over a coat of primer over a sufficent coat of wall putty complete all as specified and directed.

M&L for preparation of new plastered surface of ceiling and applying three coats of white wash complete all as specified and directed.

Taking out existing unserviceable plaster, loose unsound weaken cement concrete of any description and in any position from existing surface of RCC roof slab/ RCC facia/ beams/ columns/ RCC chajja, average depth 25mm (approximate 6.5 mtrs height from natural GL) with power driven pneumatic chiesel and removal of debries upto a distence 500 mtrs out side MD land including saw cutting of all edges, making square shoulders of cavaties and roughening of smooth surface, scraping out and removing corrosion and all loose scales, rust etc. from the visible reinforcement and cleaning the steel reinforecement properly providing NIT zink primer, Zink primer on visible reinforcement surface to form a contineous film and preparing the surface to recive concrete of epoxy grouting mortar etc. including providing necessary scaffolding complete all as specified and as directed.

M&L for applying bonding coat of modified styrene butadene emulsion in proportion 1 part (bonding agent) : 1 part (water) : 3 part (OP cement) by volume with the brushes etc. to bind new cement plaster/ polymer modified plaster/ concrete/ screed concrete with oldsurface including removal of loose/ distengrated old concrete/ plaster including preparation of surface etc. complete all as specified and as directed.

M&L for applying 25-35mm average thickness plaster on ceiling slab and chajja projections, facia and beams with polymer modified mortar firtified with SBR in proportion 1 part (cement) : 3 part (sand) by weight of cement with 11 to 15 ltrs water addition, finishing surface to match with existing adjoining surface complete all as specified and as directed.

Taking up or down 15 mm bore steel tubing and connections, incl cleaning for re-fixing or removal to store complete all as specified and as directed.

Taking up or down 20 mm bore steel tubing and connections, incl cleaning for re-fixing or removal to store complete all as specified and as directed.

Refixing old steel tubing 15 mm bore and connections in new or old position (Walls, ceiling,floors, etc.) complete all as specified and as directed.

Refixing old steel tubing 20 mm bore and connections in new or old position (Walls, ceiling,floors, etc.) complete all as specified and as directed.

S&F 15 mm dia steel tubing medium grade galvanised with all fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and as directed.

All as per item No 28 here in before but 20 mm dia.

S&F in repair Fancy type CP Long shunk bib taps 15 mm dia ,chromium plated cast copper alloy with half turn type capstan heads, screwed down screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repair Fancy type CP stop/angular cock 15mm dia cast copper alloy, chromium plated fency type screwed down high pressure with half turn type capstan heads, screwed both end for iron pipe or for unions and fixed complete all as specified and directed.

S&F 15 mm dia pillar tapes long shunks, Fancy type of Chromoum Plated brass with half turn type capstan heads screwed down high pressure, with or without lettered hot and cold with long shank, screwed shanks and fly nuts, screwed for iron pipes or for WHB complete all as specified and directed.

S&F SS shop dish of size 100mm complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair PVC valveless, syphonic action type flushing cistern, 10 ltr capacity, low level, white, with inlet, ball valve, float and handle including bracket, complete all as specified and directed.

Taking down chowkats or frame exc 1.5 Sqm and n exc 4Sqm each (without taking off shutter from the frame) complete all as specified and as directed.

Taking down chowkats or frame n exc 1.5 Sqm each (without taking off shutter from the frame) complete all as specified and as directed.

M&L Aluminium powder coated (powder coated of requried colour) three track sliding windows frame top & sides of size 92x31.75x1.50mm , bottom size 92x31.75x1.50mm and shutter top & bottom of size 40x18x1.55mm and sides (handle) of size 40x18x1.55mm and lock side shutter frame of size 40x18x1.45mm " with rubber gasket, beading and locking arrangement including making good to the disturbed portion complete including stainless steel wire mesh 0.36mm nominal dia of wire with 1.40mm average aperture and fixed with stainless steel wire staples and fixing 5mm thick glass with necessary rubber beading gasket etc complete all as specified and as directed by Engr-in-charge.

S&F aluminium powder coated (requried colour to match window colour) grill of 5 mm dia squares rectangular triangular circular shape aperture n.exc 7.00cm in length or width fixed with H or F channel complete all as specified and as directed.

M & L for Aluminium doors, powder coated (of approved colour), with frame of section 100 x 44mm x 2.5mm thick and shutter with bottom rail of section 150 x 44.5 x 2.5mm thick, middle rail of section 85 x 44.5 x 2.5mm thick and top rail of section 80.4 x 44.5 x 2.5mm thick and styles of section 80.4 x 44.5 x 2.5mm thick with 5mm thick glass (plain/tinted/with laminated film) or prelaminated board fixed in position with aluminium beading including necessary rubber gaskets and 2 Nos. aluminium push plate handle of aluminium section 150mm wide and 2.5mm thick including 150mm aluminium tower bolt, brass mortice lock complete all as per Drawing No. CEAA/TD/63 sheet No. 2.2 complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid and bedded and pointed in any mortar complete all as specified and as directed.

M&L for Green marble tiles 15-20 mm thick machine cut, beded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of Marble slab including cutting and polishing and nosing and polishing of the free or front edge of the slab in shelves, platform, window cills etc complete all as specified and as directed by Engineer-in-Charge.

M&L for machine cut kota stone slab flooring 20 - 25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including backing coat complete all as specified and as directed.

Dismantling water tanks and exc 500 but n exc 1000 litre capacity complete all as specified and as directed.

S&F rotational moulded water storage tank 1000 ltr capacity double layer (cylindrical vertical with closed top) hoisted with PVC cover thread with suitable lock arrangments and fixed in position complete all as specified and as directed.

S&F in repair 20mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

Material & Labour for complete removal of existing treatment of wall and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and as directed.

M&L for complete removal of old existing plastered surface of wall and applying two coats of distemper oil emulsion over a coat of primer over a sufficent coat of wall putty complete all as specified and as directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and as directed.

S&F for MS framed works as in purline, rafters, column square/rectangular, round or angle section, fixed with and including iron cleats or other connected plates flate iron wind ties etc incl bending of MS section as requried such as grills, gratings, etc. with ends of barsshouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290 Gde-E-165 complete all as specified and as directed.

S&F Pre- painted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550Mpa as in roof covering fixed with self tapping screws complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of new surfaces of steel or iron surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L Cement concrete 1:2:4 type B2 using 40 mm graded stone aggregate as in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases) complete all as specified and as directed.

M&L for expanded metal, cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members weight per square metre not exc 4 kg complete all as specified and as directed.

S&F mild steel steel sections for wind tie for roof including securing bolts including cutting , drilling holes notching for wire flat iron fillets and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

Hacking out old broken glass(any thickness, size, quality or description) from any frame surrounds, glazed with putty or fixed with beads complete all as specified and as directed.

S&F 3mm thick sheet glass ordinary quality and glazing complete in square not exc 0.50 sqm each complete all as specified and as directed.

Taking down shutters of any description n exc 1 sqm each and refixing in same opening complete all as specified and as directed.

M&L 30mm thick 2nd class HW, Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified and as directed.

S&F MS butt hinges 50mm long medium weight cold rolled MS fixed complete all as specified and as directed.

S&F 125 mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

M&L Preparation of new wooden surfaces over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

M&L Preparation of old wooden surfaces over 10cm width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L Exposed metal frame ceiling 8mm thick with calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600mm x 600mm grid complete all as specified and as directed.

Demolition of Concrete (unreinforced) of any description and in any position not otherwise specifically provided in cement concrete complete all as specified and directed.

M&L for providing 75 mm thick cement concrete 1:4:8 type D-2 (using 40mm graded aggregate) as in sub base complete all as specified and directed.

M&L for Machine pressed precast conctete interlocking paver block any shape and size with grey cement and pigment confirming to IS 15658-2006 of 60 mm thickness M-35 Grade over sand cushion complete all as specified and as directed. (Note - Sand will be measured and paid separately)

M &L 25mm thick sand filling (sand cushioning) under path for laying interlocking tiles complete all as specified and as directed.

Excavating in trenches not exc 1.5m wide and not exc 1.5m in depth for foundations etc or for shafts, wells, cesspits, manholes, pier holes etc not exc 10sqm on plan and getting out in soft/loose soil complete all as specified and as directed.

M&L for cement concrete Type D2 1:4:8 (40mm graded aggregate) in foundations,filling and mass concrete complete all as specified and as directed.

M&L Cement concrete 1:2:4 type B2 using 40 mm graded stone aggregate as in surface channels and drains complete all as specified and as directed.

M&L for formwork to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work all exceeding 20cm wide. (Where RCC/PCC band in walls, spanning and opening, the formwork soffit only shall be paid for under item 07010) for fair finished concrete surfaces complete all as specified and as directed.

M&L for fly ash bricks works, straight or curved on plan exc 6m mean radius, built in built in cement mortar (1:4) complete all as specified and directed.

M&L for plain cement concrete 1:2:4 type B1 using (20mm graded stone aggregate) for coping/benching and the like including weathering,slightly rounded or chamfered angles,throating including necessary use & waste of formwork complete all as specified and directed.

M&L for Rendering 10mm thick on fair faces of brick work or concrete surfaces even and smooth without using exrtra cement in CM-1:4 complete all as specified and as directed.

M&L for providing precast cement concrete 1:2:4 type B1 using (20 mm graded stone aggregate) in cover slabs for manholes, etc and similar articles with plain fair faces including chamfers, weathering, throating,formwork and set in cement mortar (1:4) with joints to match complete all as specified & directed. NOTE :- Reinforcement will be measured and paid separately

M&L for mild steel TMT bars 10mm dia, and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed.

Returning filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm, in hard / dense soil complete all as specified and as directed.

Removing excavated material n exc. 50 m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and as directed.

M&L for concealed point wiring complete with 1.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor cable 1100 volt grade, (FRLS) through and including PVC conduit pipe and its accessories, cadmium screws and including 1.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor cable(FRLS) as earth continuity conductor and MS boxes made of 16 gauge MS sheet concealed type on walls cover 3mm thick for housing the specified and directed for the following :- One light/fan point controlled by one on way switch

All as per item No 79 here in before but one socket outlet 05 Amps on the same board.

All as per item No 79 here in before but one socket outlet 05 Amps on independent board.

All as per item No 79 here in before but point wiring with 2.5 Sqmm cable and 2.5 Sqmm earth continuity conductor for 3 pin 15 Amp socket complete all as specified and as directed.

S&F Switch piano, single pole one way 5 Amps 240 volt capacity flush type complete all as specified and as directed.

S&F 3 pin 5 Amps Socket outlet , flush type complete all as specified and as directed.

Supply and fix 3 pin 15 Amps switch socket combination, flush type multi purpose 2 in 1 type (3 pin 5 Amps and 15 Amps) complete all as specified and as directed.

S& F ceiling rose, 5 Amps surface type 240 volts bakelite three terminal complete all as specified and as directed.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed.

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300m complete all as specified and as directed.

S&F in replacement of miniature circuit breaker (MCB) of single poles and current carrying capacity 6 to 32 AMP 240V, 10 KA 'C' curve, in the DB Complete with connection testing and commissioning complete all as specified and as directed.

All as per item No 90 here in before but SPN 40 AMP capacity.

S&F in repair 8 way sheet metal enclosures for flush/surface mounting distribution board double door, 240 volts factory made and tested complete, suitable for mounting MCBs with 200 Amps rated bus bar, cable lugs complete all as specified and directed.

M&L in repair for sub main wiring of two run with 04 Sqmm single core PVC insulated, FRLS, flexible multi stranded copper conductor cable 1100 volts grade, drawn through and including PVC casing-n-capping of size and one run of same size copper cable as earth continuity conductor in green color complete all as specified and as directed Including taking down old u/s sub main wiring. Note- Two runs of single core cable with one run of earth continuity cable including PVC casing-n-capping and its accessories will be measured and paid as one unit.

All as per item No 93 here in before but 6.0 sqmm.

S & F in replacement of LED batten fitting alongwith removable LED Tube 20W, 230 Volt, 6000K, wall /ceiling mounted ,LED batten fixed by means of bolts,ABS rotor suitable for single side connections. LED rod having glass material complete haivng lumen efficacy minimum 100 lm/w,CCT 6500 K, powered by integral constant current driver suitable for 240 V AC with all accessories internallly prewired including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

Supply and fixing in replacement LED light fitting 600x600 mm 36 watt 220 V AC decorative type with necessary electrical connection complete all as specified and directed.

M & L for carefully taking down and refixing split ac 1.5/2.0 tr incl fixing assy and electrical connection complete all as specified and as directed.

S&F in repair AC box including plug and MCB 20 Amps complete all as specified and as directed.

Supply and fix wall fans, complete with 230V, 450 mm sweep complete all as specified and directed by Engr-in-Charge.

TECH SERVE SOLUTIONS

DMA PROJECTS

ARTI CONSTRUCTION