Special repairs to Bldg No HT 13A Dining Hall under GE North Ambala Cantt

Amount

SCHEDULE A PART I (B/R WORKS)

Taking down cement or cement lime plaster, of any description, on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and as directed.

Material and labour for rendering 15 mm thick on faces of brick work or concrete surfaces in cement mortar 1:6, finished even and smooth without using extra cement all as specified and as directed.

Material and labour for rendering 15 mm thick on outer faces of brick work or concrete surfaces in cement mortar 1:4, mixed with water proofing compound @ 2% by weight of cement or as per manufacturer’s instructions, finished even and smooth without using extra cement all as specified and as directed. Note: Supply only integral water proofing shall be measured and paid separately.

Supply only integral water proofing compound complete all as specified and as directed.

Material and labour for preperation of newly plastered surfaces of walls and applying two coats of oil bound (acrylic) distemper using roller over a coat of 2mm thick wall care putty complete all as specified and as directed.

Material and labour for preparation of newly plastered wall surfaces and applying two coats of cement base paint complete all as specified and as directed.

Taking down chowkats or frames with shutter, area not exceeding 1.50 Square metre (w/o taking off shutters from frames) and removing from site, including cutting holes in wall/concrete for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces in CM (1:3) and finishing the surfaces to match with existing finish complete all as specified and directed.

Supply and fixing of steel window box type, with side hung shutters, using ERW hollow 'P' section, factory made, comprising double frame for and including gauged and glazed skeleton shutter, 30mm thick, jointed internally with flat iron 25x3mm complete including hinges, handle, tower bolts, stops, lugs etc. all as shown on drawing No. TD-219 sheet 1/3 to 3/3 and TD-220 sheet 1/3 to 3/3 and applying two coats of approved colour synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. Note: (i) For the purpose of measurement and payment double shutter both glazed and gauzed with frame shall be considered as one unit. (ii) Unit rate quoted against this item shall also include the iron mongery and grill 10 mm square bar irrespective of whatever shown on drawings including painting (iii) Glazing, wire mesh and painting shall be measured and paid for separately.

Supply and fixing of sheet glass, 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 sqm in each pane complete all as specified and directed.

Taking down chowkats or frames with shutter, area exceeding 1.50 Square metre and not exceeding 4.00 Square metre (without taking off shutters from frame) and removing from site, including cutting holes in wall/concrete for taking out existing hold fasts and making good the disturbed portion of jambs and adjoining surfaces in CM (1:3) and finishing the surfaces to match with existing finish complete all as specified and directed.

Supply and fixing of first class hard wood, 35mm thick, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, elc.;sizesof me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed.

Supply and fixing of galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staples complete all as specified and directed.

Supply and fixing of rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe-290 (Gde E-165) complete all as specified and directed.

Supplying and fixing of factory made 35mm thick, 2nd class HW, plain framed, panelled shutters (two panel) with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed. (Note: Pattern of door shall be same as that of existing doors.)

Supply and fixing of 200 mm long aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and as directed.

Supply and fixing of 125 mm long, aluminium handle, cast type, anodized, ISI Marked complete, all as specified and as directed.

Supply and fixing 300 mm aluminum anodised sliding door bolt, ISI marked, with hasp, staple (bolt type) complete with clamps bolt not less than 16mm dia and fixing clips of sheet, cast or extruded section and fixing bolts an sliding bolt of extruded section or cast aluminum alloy, complete, all as specified and directed..

Supply and fixing of mild steel, 150mm, ordinary rat rail rod pattern springs for door including roller and roller plate fixed to wooden chowkats or welded to angle iron door frames complete all as specified and as directed.

Material and labour for preparation of new or previously untreated steel surfaces, of any description not otherwise described, over 10 cm width or girth and applying two coats of approved colour synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.

Demolition of brickwork built in cement mortar including all quoins, arches, pillars etc, complete all as specified and as directed.

Material and labour for brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6 metre mean radius, built in cement mortar (1:6) complete all as specified and as directed.

All as above item No 1 but except bricks complete all as specified and as directed. Note: Old serviceable bricks as obtained from serial item No 1.09 hereinbefore shall be reused after cleaning the tiles. The rate quoted shall include for cleaning the tiles also.

Material and labour for taking down roof trusses, coupled rafters or trussed beams, clear span above 4 metres and upto 8 metres complete all as specified and as directed.

Supply and fixing of mild steel rag or lewis bolts, purpose made, with hexagonal or square nuts and washers, screwed at one end and the other end enlarged and jagged or lewised, exceeding 30cm long and 12mm dia of neck complete all as specified and as directed.

Demolition of reinforced concrete in ground floors and pavings not exceeding 15cm thickness (below or above ground level), roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work, reinforcement cut as required to facilitate demolition complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) including floor tiles, screed bed etc complete all as specified and as directed.

Material and labour for PCC 1:2:4 type B0 using 12.5mm graded stone aggrgate as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, kneelers, apex stones, bed plates,coping, kerb, water trough and the like including weathering slightly rounded or champfered angles and throating as directed including use and waste of formwork finishing exposed concrete surface fair and even complete all as specified and directed.

Material and labour for mild steel TMT bars of 10mm dia and over, as in reinforcement, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Material and labour for mild steel TMT bars of 6 to 8mm dia and over, as in reinforcement, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

Dismantling of asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and as directed.

Supply & fixing for pre-painted galvalume, aluminuim zinc coating, GI based corrugated (SINOSUIDAL PATTERN) steel sheet, 0.80mm thick, conforming to IS-15961, of any colour, having tensile strength of 550 MPa, as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. Note- The sheets shall have super durable polyester quality paint of approved colour, 150 gm/sqm total on both sides, suitable for exterior application conforming to IS-15965.

Supply & fixing for pre-painted galvalume, aluminuim zinc coating, GI based Plain steel sheet, 0.50mm thick, of any colour, having tensile strength of 550 MPa, as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed. Note- The sheets shall have super durable polyester quality paint of approved colour, 150 gm/sqm total on both sides, suitable for exterior application conforming to IS-15965.

Supply and fixing of rolled mild steel sections as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.quality conforming to Fe-410-W Grade E-250 quality-A complete all as specified and as directed.

Supply and fixing of rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment, any thickness, quality conforming to Fe-410-W Grade E-250 quality-Acomplete all as specified and as directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards, slabs, blankets, any thickness, including cover fillets complete all as specified and as directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position, framed work complete all as specified and as directed.

Supply and fixing of GI metal suspended ceiling system at all heights of Perforated with fleece 600x600x0.5mm TEULAR EDGE TILES in global white powder coated with 60-70 micron front coating laid on 24mm wide tee grid – strong section flanges colour white having stitching on the main runner, 600 mm and 600 mm cross tees with web height of 26mm. The tiles should have humidity resistance (RH) of 100%, with light reflection of 62%. The main runner spaced at 600 mm max (centre to centre) securely fixed to the structural soffit . Hangers (GI wire of 4 mm dia) to be fixed by approved roof plug, level adjusters and screws etc at 600x600 intervals as appropriate height.The first/last suspension system at the end of each main runner should not be greater than 450mm from the adjacent wall. Flush fitting 600mm long cross tees to be interlocked between main runners to form 600 x 600 mm with grid module(24X38X0.3mm).Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 600 mm cross tees. Perimeter trim to be wall angles of size 3000x22x22mm, secured to walls at 450mm max (centre to centre), including PVC clips to hod the ceiling tile and celing fixed as required on appropritae height complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for dismantling floor, hearth or wall tileing including cement mortar bedding (but not backing), removing servicable tiles to store and rubbish off the premises complete all as specified and as directed.

Material and labour for premium quality, joint free, anti skid porcelain coloured tiles (Square/rectangular), area of each tile exceeding 0.18 sqm and not exceeding 0.36 sqm and 7 to 8 mm thick, laid in floor over and including cement screed bed 15mm thick in cement mortar (1:4) and set and jointed in neat cement slurry @ 3.00 kg/Sqm and pointed in white or coloured cement to match the tile colour complete all as specified and directed.

Material and labour for premium quality, joint free, anti skid porcelain coloured tiles (Square/rectangular) of the same lenght of floor tile but 150mm high , on vertical surfaces of walls over and including 10mm thick rough finished plaster in cement mortar (1:4), set, jointed in neat cement slurry and pointed in coloured cement to match tile colour complete all as specified and directed.

Material and labour for premium quality, glazed coloured ceramic tiles of size 450 x 350 x 7mm thick or 350mmx250mmx7mm thick, on vertical surfaces of walls over and including 10mm thick rough finished plaster in cement mortar (1:4), set, jointed in neat cement slurry and pointed in coloured cement to match tile colour complete all as specified and directed. Note:- Size of tile shall be cut as required.

Material and labour for PCC 1:3:6 type C-1 (using 20 mm graded mechanically crushed stone aggregate), 50mm thick, as in plinth protection/PCC path and paving, laid in panels of area not exceeding 1.20 sqm with 12mm wide joints filled with mastic (using bitumen and sand mixture applied hot in the ratio of 1:3 by weight) formed at the end of each panel and change in direction of plinth protection/PCC Path and paving and finishing the top surface even and smooth without using extra cement complete all as specified and as directed.

Material and labour for preparation of new or previously untreated wooden surfaces, of any description not otherwise described, over 10 cm width or girth and applying two coats of approved colour synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Supply and fixing in repairs of MS powder coated decorative curtain rod, 20mm dia, fixed with decorative brackets, stop roller and finials at the end including rings at 10 per running metre including taking down of existing unserviceable curtain rod of any type and pattern complete all as specified and as directed.

SCHEDULE A PART II (INTERNAL ELECTRIFICATION)

Taking down carefully any type of point wiring (light, fan, socket or power) complete with fittings such as switches, ceiling roses, pendants, regulators, sockets, tube light fittings with all accessories etc., and/or drawing out from existing conduit/batten and removal of materials from site and making good the disturbed surfaces of wall, floors, ceiling etc to match with the existing surfaces with matching OBD/White wash/Distemper complete all as specified and as directed.

Material and labour for concealed point wiring using approved colour coding as per IS, with multi stranded copper conductor 1.5 sqmm (Nominal area), single core, FRLS, 1100 volts, ISI marked, PVC insulated and unsheathed stranded cable drawn through and including non metallic, medium grade PVC concealed conduit not less than 20mm dia and its fittings including all tees, bell mouth pieces and fixing accessories such as couplers, saddlers, pipe hooks etc, PVC junction boxes, ISI marked including mild steel sunken boxes, made out of 1.6mm thick mild steel sheet, with earth dolly, coated with two coats of anti corrosive paint over a coat of red oxide primer internally, covered with 3mm thick decorative laminated sheet top cover of Hylam for fixing of switches, socket outlets, fan regulators etc. including 1.5 sqmm single core PVC insulated and unsheathed FRLS cable, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor upto common earth and connecting to common earth dolly with suitable size of lugs complete all as specified and directed for one light point/ bell point controlled by one switch complete all as specified and as directed. Notes :- (i) Switch, socket and fan regulators to be measured and paid for separately. (ii)PVC Conduit conforming to IS 9537 part I & III. (iii) All chases will be cut by chase cutter only. Make of PVC Conduit- Finolex, Polycab, Kalinga Premium Make of PVC wire- Finolex, Polycab, Havells

Description all as per Srl item No.2.02 here in before but for one fan/Exhuast fan point controlled by one switch 5 Amp and fan regulator.

Description all as per Srl item No.2.02 here in before but for one 3 pin socket outlet point 5 Amp on Independent board.

Description all as per Srl item No.2.02 here in before but for one 3 pin socket outlet point 5 Amp on same board.

All as per the description of Serial Item No 2.02 above, but with 2.5 Sqmm PVC, HRFR, unsheathed, multistranded cable, for one socket point 15 Amps, 1100 volts grade, ISI marked, including 2.5 Sq mm size, green colour, PVC insulated HRFR, continuous copper earth wire and connected to common earth dolly complete all as specified and as directed. Note- Switch, Socket shall be measured and paid separately and Steel junction boxes shall be used wherever junction boxes are to be fitted.

Supply and fixing of switch, piano, fush type, single pole, one way, 5 Amps, one module, 230 volt, ISI marked complete all as specified and as directed. Make: Anchor/Fine/SSK.

Supply and fixing of switch, piano, flush type, single pole, one way, 15 Amps, one module, 230 volt, ISI marked complete all as specified and directed. Make: Anchor/Fine/SSK.

Supply and fixing of socket, 2/3 pin, 5 Amps, ISI marked complete all as specified and directed. Make: Anchor/Fine/SSK.

Supply and fixing of socket, 2/3 pin, 6/16 Amps, combined, ISI marked complete all as specified and as directed. Make: Anchor/Fine/SSK.

Supply and fixing of electronic fan regulator, step type, 230 volts, AC, suitable for ceiling fan, any type/make/sweep complete all as specified and as directed. Make: Anchor/Fine/SSK.

Supply and fixing of ceiling rose surface bakelite 65x50mm, 2 to 3 terminals complete all as specified and as directed. Make: Anchor/Fine/SSK.

Supply and fixing of lamp holder, insulated body, with back plate for angular batten fittings with one PVC block of size 75mm x 75mm for mounting the fittings with and including one LED 9 watt lamp complete all as specified and as directed. Make: Lamp Holder : Anchor/Fine/SSK. LED bulb : Wipro/Havells/Philips

Supply and fixing of batten tube light channel suitable for LED tube, single wall/ceiling mounted with all accessories internally prewired and including LED tube light 18 watt lamp, with aluminium heat shrink, high frequency, power factor of 0.90, suitable for connecting up with twin core copper conductor cable of size 23/0.0076 from ceiling rose to connector of the light fitting complete all as specified and as directed. Make for Batten: Havells Cat Pt No. (Fitting) REGAL BATENT8 4TPO 1X22WSSABSWH, Wipro Cat Pt No. WI0921208, Philips Cat Pt No. TMC501 1XT-LED 22W P3241 Make for Tube: Havells Cat Pt No. CRYSTAL 1213 T8DSTL 20WLED865SGLASS, Wipro Cat Pt No. LC13181, Philips Cat Pt No. 20W865 T8 INDI-2100Lm

Supply, insatallation, commissioning and testing of TPN distibution board, vertical type, 4 way, double door, powder coated, IP 43, including 200 Amps fully insulated copper bus bar, 125 Amps MCCB TPN 100 Amps, fixed on wall duly grouted in solid block wall or on wooden board with and including copper lugs/thimbles of MCB TPN rating used with wire for fixing in MCCB complete all as specified and directed. Make- Siemens/ Legrand/ Schenider Acti 9/ Hager Nevello Plus/ INDOASIAN(Optipro)

Supply and fixing of sheet metal enclosures for distribution board for MCBs, SPN, 8 ways, double door, 240 volts, with and including 200 amps rated bus bar, with acrylic door, fixed on wall duly grouted in solid block wall or on wooden board with and including copper lugs or thimbles duly crimped connection and taking down and removal of existing DB's of any type complete all as specified and as directed Make- Siemens/ Legrand/ Schenider Acti 9/ Hager Nevello Plus/ INDOASIAN(Optipro)

Supply and fixing of MCB, single pole, 240 volts, 50Hz, breaking capacity 10KA, 'C' curve 6 to 32 Amps, ISI marked including taking down and removal of old unserviceable MCB of any capacity and type complete all as specified and as directed. Make- Siemens/ Legrand/ Schenider Acti 9/ Hager Nevello Plus/ INDOASIAN(Optipro)

Supply and fixing of RCBO, 2 module, 230 volts, with IP protection, with earthfault indicator and positive contact indicatior of 40 Amps capacity and sensitivity, 300mA (HI immunity) including taking down and removal of old unserviceable item of any capacity and type complete all as specified and directed. Make- Siemens/ Legrand/ Schenider Acti 9/ Hager Nevello Plus/ INDOASIAN(Optipro)

Supply and fixing of over voltage release, 230 volts, single phase, in one module suitable for single phase and nuetral including removal of unserviceable existing item complete all as specified and directed. Make- Legrand/Schenider/Hager Cat Part No. MZ209

Material and labour for new earthing complete with galvanised earth plate electrode 600mm x 600mmx 6mm thick surrounded by charcoal and salt, buried directly in ground vertically in a pit of depth not less than 2.25m below ground level with top edge of the earth plate not less than 1.5m below normal ground level, connected to 4.00 mm GI wire earth lead by means of bolts, nuts, checks nut and washers made out of galvanized iron or steel, earth wire protected by galvanized steel pipe 15mm dia (medium grade) and connected to main switch or main control board all as shown in Electrical Plate No.3 of SSR Part-I & including necessary excavation and earth work in any type of strata, PCC (1:3:6) type C1 in pit, RCC cover slab 50mm thick in 1:2:4 type B-1 using 8mm dia TMT bars @10cm c/c both way with one 8mm dia bar as handle for lifting, 20mm dia GI medium grade watering pipe, funnel, wire wesh, charcoal or coke & salt in alternate layers, etc.all as indicated including testing on completion complete all as specified and directed. Make: Havells Cat Pt No. ENDURAPEARLNEOSL40WLED757 PASYTOPC, Wipro Cat Pt No. LRO2-45I-XXX-57-XX, Philips Cat Pt No. BRP409LED 040CWHOMRFGSIPSUGR

Supply and fixing in repair of LED security light fittings of capacity 45 watts, made up of cast aluminium body housing with black epoxy powder coating with cover heat resistant glass safety input voltage range 170 to 270 volts, 0.95 power factor and other connected accessories including service bracket of GI pipe of 32mm dia, medium grade, of 0.90metre length bent to required length and fixed to wall with two clamps made of 40x6 mm mild steel flat iron 15cm long, 4 Nos 8mm dia bolts with nuts complete with all accessories, internally pre wired and connecting with 3 core copper conductor flexible cable from terminal box to the ceiling rose or connector of the light point including disconnecting and taking down of existing light fitting and removing from site complete all as specified and as directed. Make- Philips/Havells/Crompton Greaves

Supply and laying of cable, XLPE, insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cable (heavy duty), 1100 volts grade, with stranded aluminium conductor of size 3.5 core, 25Sqmm and laying in trenches complete all as specified and as directed. Make of cable- Gloster/Finolex/Havells

Excavation in trenches not exceeding 1.50 metre wide and not exceeding 1.50 metre in depth and getting out in soft/loose soil for laying of cable complete all as specified and as directed.

Returning filling in, in soil, including spreading leveling watering and well ramming in layers not exceeding 25 cm each complete all as specified and as directed.

Removing excavated spoil/materials to a distance not exceeding 50 metre and depositing where directed at level not exceeding 1.5 above the starting point complete all as specified and as directed.

Material and labour for fine and dry sand, cushioning for underground cable, by providing a layers of sand 8cm deep before laying and 15cm deep after laying the cable including stretching the cable and punning sand cushioning complete all as specified and as directed. Note - Punned thickness of sand layer shall only be measured and paid to contractor.

Supply and laying un-reinforced, precast concrete cable cover, class LV type 1, Flat, with peak, size 250 mm 150 mm x40 mm complete all as specified and as directed.

Taking down fan, sealing cable end, dismantling blades and removing fan including painting of ceiling fans with synthetic enamel paint by spraying including filling cavities with filler over one coat of painting after cleaning all dust etc complete all as specified and as directed.

Supply and fixing in replacement of surface mounting downlighter LED, 15 watt, white, adjustable, powder coated aluminium cover with anodised aluminium reflector, prewired and connecting with twin twisted copper flexible cable of size 23/0.0076 from ceiling rose to connector of the light fitting complete all as specified and as directed.

Material and labour for sub main wiring with two single core FRLS, ISI Marked, PVC insulated, unsheathed, copper conductor cable, 6 sqmm, housing in and including capping and casing of adequate size with accessories on surface of wall or ceiling with one additional single core PVC insulated, stranded copper conductor, FRLS, ISI Marked, 6 sqmm, green colour for earth continuity conductor including taking down of old unserviceable sub main wiring, any size and any type complete all as specified and directed. Note- Three runs of 6 sqmm cable and one run of casing and capping conduit shall be measured as 1 unit. Make- Havells/Polycab/Finolex

Note:- Amount of credit of Rs. 90,639.00 for retrieved materials is mentioned in Schedule of Credit Page Nos.101R of tender documents in pdf form which will be deducted offline while acceptance of tender.

M/s Vridhi Construction Co.

V K Constructive Builders

s.v.builders