Construction of One Workshop and One Theory Room Extension at ITI, Lalpur, Dist.Jamnagar

Name of Work:-Construction of one workshop and one theory room extension at ITI -Lalpur,

BILL OF QUANTITIES

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

1 Excavation for foundation in Hard murrum incl. 160.00 Cum. 273.45

sorting out and stacking of useful materials

and disposing of the excavated stuff up to all

2 Excavation for foundation in Soft rock not 253.00 Cum. 300.57

requiring Blasting incl. sorting out and

stacking of useful materials and disposing of

the excavated stuff up to all lead and lift.

3 Filling in plinth with sand under floors 61.00 Cum. 489.28

including watering, ramming consolidating

and dressing etc. complete. ( more than 10 ton

4 Filling available excavated earth (Excluding 160.00 Cum. 137.47

rock) in trenches plinth, sedes of foundation

etc in layers not exceeding 20 cm in depth

consolidating each deposited layer by

ramming and watering etc. comp.

5 Filling in foundation and plinth with murrum or 317.00 Cum. 304.60

selected soil in layers of 20cm. thickness

including watering, ramming and

consolidating etc. complete.

6 Applying general insecticide pest control 304.00 Sqm. 91.63

treatment to floors, cupboards etc including

labour materials etc. complete.Using

Imidacloprid 30.5 SCas Per IS 6313 part -II(

(0.075% concentration by mass) is

recommended 10.5ml chemical diluted with

liters of water application 0.5 litre chemical

/Sqm of surface is recommended as per I.S

7 Providing and laying controlled cement 17.00 Cum. 4025.76

concrete M.150 for curing complete excluding

cost of formwork and reinforcement for

reinforced concrete work in Foundations,

footings,Base of columns and Mass concrete

8 Pro. & laying controlled cement concrete M-25 43.00 Cum. 4649.03

and curing complete inclu. the cost of form

work and foundation, footings, base of column

and mass concrete.

9 Providing and laying controlled C.C. M.25 & 13.00 Cum. 7481.07

curing complete including the cost of form

work but excluding the cost of reinforcement

for reinforced concrete work in Collumns, up

1 of 28 DTP of ITI workshop at Lalpur 01-26

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

10 Providing and laying cement concrete 1:4:8 ( 1 104.00 Cum. 2941.12

cement: 4 coarse sand: 8 crushed stone

aggregate 40 mm nominal size ) and curing

complete excluding cost of form work in

foundation and plinth.

11 Providing and laying Controlled cement 19.00 Cum. 7481.07

concrete M-25 and curing complete including

the cost of formwork and excluding cost of

reinforcement for reinforced concrete work in

Column FOR all floors.

12 Providing and laying Controlled cement 31.00 Cum. 6076.16

concrete M-25 and curing complete including

the cost of formwork and excluding cost of

reinforcement for reinforced concrete work in

13 Providing and laying Controlled cement 39.00 Cum. 5959.00

concrete M-25 and curing complete including

the cost of formwork and excluding cost of

reinforcement for reinforced concrete work in

Beam for all Floor

14 Providing and laying Controlled cement 5.00 Cum. 6502.38

concrete M-25 and curing complete including

the cost of formwork and excluding cost of

reinforcement for reinforced concrete work in

Lintel for all Floor

15 Providing and laying controlled cement 3.80 Cum. 7142.72

concrete M25 and curing complete including

the cost of form work but excluding the cost of

reinforcement for reinforced concrete work in

chhaja cantilever up to floor two level for all

16 Providing and laying Controlled cement 45.00 Cum. 6751.85

concrete M-25 and curing complete including

the cost of formwork and excluding cost of

reinforcement for reinforced concrete work in

Slab for Ground Floor

17 Providing and laying Controlled cement 6.00 Cum. 7112.42

concrete M-25 and curing complete including

the cost of formwork and excluding cost of

reinforcement for reinforced concrete work in

wall caps / coping for all floor.

18 Providing TMT Bar FE 500D reinforcement for 43304.00 Kg. 77.29

R.C.C. work including bending, binding and

placing in position complete for all Floor.

19 White Stone Bela mesonry block in course in 64.00 Cum. 6320.84

Foundation and plinth with stone of approved

quality in Cement Mortar 1:5 (1-Cement : 5-

Course sand) including packing the joints etc.

2 of 28 DTP of ITI workshop at Lalpur 01-26

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

20 White Stone Bela mesonry block in course in 191.00 Cum. 6647.02

superstructure with stone of approved quality

in Lime Mortar 1:5 (1-Cement :5- course sand)

including packing the joints etc. complete for

21 White Stone Bela mesonry work in partition 201.00 Sqm. 696.51

walls upto 15 cm thickness in cement Mortar

1:4 ( 1- Cement : 4- course sand)etc complete

22 Providing and fixing in position collapsible 2.40 Qntl. 6217.76

steel shutters with vertical channels 20 x 10 x

2 mm braced with flat iron diagonals 20 x 5 mm

size with top and bottom rails of T_rin 40x 40 x

6 mm with 38mm dia, steel pulleys complete

with bolts, nuts, locking arrangements,

stoppers handles including applying a priming

coat of red lead paint.

23 Providing and fixing 35 mm thick Flush door 3.00 Sqm. 3894.56

shutters , solid core construction with frame of

first class hardwood with cross board and

face veneer or plywood face panels with both

side 1 mm thick laminated sheet including

Indian Teak Wood Frame 12 x7 cm size

including Screw, Khili, SS hinges,SS handle

megnate, stopers etc including Colour(One

coat of primer and two coat of enamel paint) of

Frame and edges of flush door shutter for D1

24 Providing and fixing 35 mm thick Flush door 5.00 Sqm. 4275.33

shutters , solid core construction with frame of

first class hardwood with cross board and

face veneer or plywood face panels with both

side 1 mm thick laminated sheet including

Indian Teak Wood Frame 12 x7 cm size

including Screw, Khili, SS hinges,SS handle

megnate, stopers etc including Colour(One

coat of primer and two coat of enamel paint) of

Frame and edges of flush door shutter for D2

25 Providing and fixing FRP FRAME size 100 x 50 2.00 Sqm. 2377.76

mm and 28 mm thick FRP Depress panel

shutter having extra reinforcement in sides

and edges and in Get coat finish.The core of

the shutter and frame is to be filled up with

injected fire retardant grade polyurethane

foam done in situ along with embedded

wooden pieces for stiffening and also taking

hinges and fixtures.The whole FRP frame and

shutter is to be water proof,weather

proof,termile proof and resistant to mild

acid/Alkali.Rates are to be inclusive of

S.S.hinges with necessary screws and SS

fixtures and fastening. Agency should have

years performance Guarantee and company

have ISO 9001-2000 certificate.

3 of 28 DTP of ITI workshop at Lalpur 01-26

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

26 Providing and fixing colour anodized aluminum 43.00 Sqm. 4001.62

sliding three track window of Jindal Series C

(20mm) or equivalent having frame bottom

section size 92mm x 31.75mm Of Jindal

Section 21651 & side and top section size 92x

31.75mm of Jindal section 21650 including

shutter frame size 50 x 20mm of Jindal section

20530 with sliding type three shutters with

5mm thick transparent tinted float glass with

rubber gasket , air lock strip and finishing joint

with transperant silicon sealent , heavy type

handle, bearing, fixture and fastening etc.

including all labour and material etc.

27 Providing and fixing rolling shutters of 19.00 Sqm. 3686.09

approved make made of 80 mm wide M.S.

laths inter-locked together through their entire

length and jointed together at the ends by end

locks mounted on specially designed pipe

shaft with bracket plates, guide channels and

arragements for inside and outside locking

with push-pull operation including the cost of

hood cover and spring etc. complete.(A)

Shutters having width below 3.5 M. with

priming coat and two coat of oil paint.

28 Providing upto floor two level 50mm thick 43.00 Sqm. 786.47

precast cement concrete jali or grill 1:2:4 mix

(1- Cement : 2- coarse sand : 4-graded stone

aggregate 6mm nominal size) reinforced with

1.6 mm dia. Mild steel wire including

roughening,cleaning, fixing and finishing in

cement mortar 1:3 and curing complete.

29 Providing and fixing fix louvers: 114 mm wide 3.00 Sqm. 2671.45

G.I. sheet having thickness of 0.55 mm &

weight not less than 490 gm /meter, roll

formed to create 84 mm wide louver snap fixed

on special shaped G. I. Channel. Fix louvers &

Channels shall finished with powder coating of

55 micron per detailed drawing and as

directed by Engineer in charge etc.complete.

30 Providing and fixing standard extruded of 3.00 Sqm. 1833.29

alluminium section of size 63mm x 38.10mm x

1.95mm (Jindal Section : 4605@ Wt. 1.094 Kg.

per Rmt.) with colour anodized alluminium

frame for ventilation with 5mm thick

Transparent bronze colour tinted float glass

as details etc. complete for Fix window.

4 of 28 DTP of ITI workshop at Lalpur 01-26

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

31 Providing and fixing Rat Mesh Grill having 43.00 Sqm. 1506.92

55x55x6mm flat in square pattern with 12.5 x

12.5 mm 18 gauge S.S. Jali including

necessary nut, bolts , hold fasts two coat oil

painting and one coat of primer etc complete.

32 Providing and fixing M.S.Grills of required 1175.00 Kg. 117.16

pattern with M.S.Flats at required spacings

and frame alround,square or round bar,with

round headed bolts and nuts or by screws

plain grill including approval quality of primer

and two coat of oil painting etc.

33 Providing and laying granite slab (18mm thick) 62.00 Sqm. 2716.90

flooring over 20mm thick base of cement

mortar 1:3 (1-cement : 3- coarse sand and

jointed with grey cement slurry including

rubbing and flooring with single pieces on

width of staircase and moulding the edge and

manage groove etc. complete.

34 Providing and fixing 18mm thick black granite 288.00 Sqm. 3174.43

stone in Jambs & sills for door over 10mm

(Average) thick base of cement mortar 1:3 (1-

cement : 3-coarse sand) laid over and jointed

with grey cement slurry including rubbing and

polishing etc. complete.

35 P & L 24" x 24" vitrified 8 mm thick tile flooring over 94.00 Sqm. 1472.91

20 mm (average) base of cement mortar 1:6 (

cement: 6 coarse sand) on new surface or fixing on

existing flooring by adhesive material including

dismentaling of existing flooring and jointed with

color cement slurry including finised with flush

pointing & cleaning the surface etc. complete for

DARK shade /Light Shade

36 Providing and laying 8" thick Ironite flooring in C:C 250.00 Sqm. 1301.89

(M-200) laid in 1st layer of 188 mm thick & 2nd layer

of Ironite material 2 kg/m² of 12mm thick mixing

with ratio of 1:4 with dry cement finished with

phase Trimax floater disc incl. material, labour and

as per following method incl. expansion joint at

mt. c/c as per instruction Method of Ironite mixing :

Mix well Ironite & cement in dry condition & take

one part by volume of the above mixed material and

two volume of grit 6mm to 2mm size & mix well in

dry condition the grit should be of hard stone clean

& without dust. Add water 80 liter to 90 liter (Ration

0.4 to 0.45) water should be clean portable & non

Acidic. Method of before laying : Surface of the

graynplythic layer must be rough and without

water on the surface. At the time of laying : Initial

setting i.e. if ceases the thumb impression control

of quantity of water take care to see the Ironite is

mixed properly and evenly in the mix. After laying :

See that it is properly leveled after formal setting of

flooring keep the are of the flooring under water for

8 to 10 days before use and necessary instruction

by Architect. Machine mixed and floater Dish

finished Ironite (200 mm. thick concrete mixture

machine and vibrator is compulsory)

5 of 28 DTP of ITI workshop at Lalpur 01-26

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

37 Providing and laying Ceramic tiles 6mm thick 15.00 Sqm. 1017.30

in flooring treads of steps and landing laid on a

bed of 12mm thick cement mortar 1:3 (1-

cement : 3-coarse sand ) finishing with flush

pointing in white cement.

38 Providing and laying coloured glazed tiles of 159.00 Sqm. 1523.67

the size 300 mm x 200 mm x 8 mm / 300 mm x

450 mm x 8 mm in skirting, risers of steps and

dedo on 10 mm. thick cement plaster 1:3 (1

cement : 3 coarse sand) & jointed with white

39 Providing and laying 50mm thick cement 356.00 Sqm. 339.08

concrete flooring 1:2:4 (1-cement : 2-coarse

sand : 4-graded stone aggregate 20mm

nominal size) laid in one layer and finished

with a floating coat of neat cement.

40 Providing and mixing water proofing materials 130.00 Bag. 49.26

in cement mortar in proportion recommended

by the manufacturer.

41 Providing using polyester fiber (6mm) with 130.00 Pkt. 26.26

triangular or equivalent cross section with

specific gravity 1.35 to 1.40 (as a secondary

reinforcement) in mortar of any grade at the

rate of 125gms. per 50 Kg. of Cement

42 Providing and laying broken China Mosaic 356.00 Sqm. 779.70

Flooring for Terrace using 12mm to 20mm

broken pieces of glazed tiles to be laid over

cement mortar 1:3 to plain or slope and to be

tempered to bring mortar crème out upto

surface using white cement including

rounding off junctions and extending them up

to 15cm. along the wall, clearing with water

and oxalic acid etc. as directed.

43 Providing and fixing pre-cast Rubber Dye / 296.00 Sqm. 707.54

steel Dye inter locking concrete block 60mm

thick with grade of concrete M300 pnumatic

compressed / vibrated mechanically and as

per approved design Confirming to IS 15658 :

2006 including 35 mm Sand layer for levelling

and filling the joint with sand in proper line and

level as per guidlines of IRC : SP 63-2018 etc.

44 Providing and fixing pre-cast concrete kerb 30.00 Rmt. 410.41

stone of gray cement based concrete block

30cm length,30cm height and 15cm thick of

M200 grade concret as per approved design

and including excavation for fixing in proper

line and level,filling the joint with C:M 1:3

(1cement:3fine sand) etc complete.

6 of 28 DTP of ITI workshop at Lalpur 01-26

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

45 Painting lines, deashes, arrows, letters etc on 45.00 Sqm. 59.17

roads, Air fields and like in two coats with

road marking paint, brushing including

cleaning the surface of all dirt, dust and other

foreign matter.(i) Over 10cm in width

46 Providing & laying both side POLISHED 26.00 Sqm. 843.35

KOTAH STONE SHELVES to C.B. with making

the grooves in the walls and fixing the kotah

stone finishing the same with cement mortar

1:2 etc. complete.

47 Making Frame type cupboard of 18mm thick 24.00 Sqm. 5807.50

water proof plywood shutter with 1.00 mm

lamination for outside and inside 0.8mm

lamination for cupboard incl. necessary

hydraulic type SS hinges, fixtures and

fastening and locking arrangement complete

48 Providing 15mm thick cement plaster in single 1012.00 Sqm. 205.28

coat on brick concrete walls for interior

plastering upto floor two level and finished

even and smooth in (ii) Cement Mortar 1:4 (1-

Cement:4-sand) incl. two coats of Birla for

asian Acrylic lappy (Putty) and two coats of

primer of approved brand. etc. comp. for all

49 Providing 10mm thick cement plaster in single 450.00 Sqm. 179.11

coat on brick concrete walls for interior

plastering upto floor two level and finished

even and smooth in (i) Cement Mortar 1:3 (1-

Cement:3 sand) incl. two coats of birla or

Asian Acrylic lappy (Putty) and two coats of

primer of approved brand etc. comp.for all

50 20mm thick sand faced cement plaster on 661.00 Sqm. 323.21

walls upto height 10 metres above ground

level consisting of 12mm thick backing coat of

C.M. 1:3 (1-cement :3-sand) and 8mm thick

finishing coat of C.M. 1:1 (1-Cement: 1-sand)

51 Providing 20mm thick water proof cement 14.00 Sqm. 319.16

plaster for sunk in single coat on brick

concrete wall for interior plastering upto floor

two level finished even and smooth (ii) Cement

Mortar 1:3 (1-Cement:3-sand) and mixing

water proofing materials of approved brand

and manufacture in cement mortar in

proportion recommended by the manufacturer

for all floors.

52 Providing and fixing chiken mesh jali with 88.00 Sqm. 217.15

square of 12.50 x 12.50 mm of 25 gauge at

junction the Brick.masonary and

reinforcement cement concrete member, work

done before plastering work including

scaffolding etc complete.

7 of 28 DTP of ITI workshop at Lalpur 01-26

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

53 Filling in foundation and plinth with brick Bats 7.00 Cum. 625.47

Chhara in layers of 20cm. thickness including

watering, remming and consolidating etc.

54 Wall painting (two coats) with plastic emulsion 1012.00 Sqm. 86.38

paint of approved brand and manufacture on

undecorated wall surface to give an even

shade including throughly brushing the

surface free from mortar droppings and other

foreign matter and sand papered smooth.

55 Wall painting (two coats) with plastic emulsion 450.00 Sqm. 92.03

paint of approved brand and manufacture on

undecorated ceiling surface to give an even

shade including throughly brushing the

surface free from mortar droppings and other

foreign matter and sand papered smooth.

56 Finishing wall with weather proof exterior 661.00 Sqm. 122.14

emulsion paint on wall surface (two coats) to

give an required shape even shade after

thoroughly brushing the surface to remove all

dirt, and remains of loose powdered materials

57 Providing and fixing 90 cm high stainless steel 28.00 Rmt. 3487.53

railing made from anticorrosive 304 grade SS

pipe of 50mm dia (16 gauge)as hand rail with

S.S. 304 grade Baluster of 36mm dia (10

Gague) as a vertical support fixed in RCC slab

at 0.60m c/c in including S.S. pipe with baluter

including accessories as per detailed

drawaing as directed etc. complete.

58 Providing laying and jointing in true line and 40.00 Rmt. 148.12

level 40mm dia. U.P.V.C. Pipe ( SCH- 40) for

cold water including fittings as approved by

Engineer In Charge. Pipe shall be fixed on the

wall with the help of clamp at every two metre

C/C or shall be concealed as directed

including necessary fittings etc. including

testing of pipe and joints and fixing the same

with adhesive solvent, including cost of all

59 Providing laying and jointing in true line and 70.00 Rmt. 91.84

level 25mm dia. U.P.V.C. Pipe ( SCH- 40) for

cold water including fittings as approved by

Engineer In Charge. Pipe shall be fixed on the

wall with the help of clamp at every two metre

C/C or shall be concealed as directed

including necessary fittings etc. including

testing of pipe and joints and fixing the same

with adhesive solvent, including cost of all

8 of 28 DTP of ITI workshop at Lalpur 01-26

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

60 Providing laying and jointing in true line and 90.00 Rmt. 72.65

level 15mm dia. U.P.V.C. Pipe ( SCH- 40) for

cold water including fittings as approved by

Engineer In Charge. Pipe shall be fixed on the

wall with the help of clamp at every two metre

C/C or shall be concealed as directed

including necessary fittings etc. including

testing of pipe and joints and fixing the same

with adhesive solvent, including cost of all

61 Providing and fixing PVC SWR Nahni Trap IS 13.00 No. 600.23

14735 for drain 100 mm diameter with jali of

the following nominal diameter of self cleaning

design with scread down or hinged grating

including the cost of cutting and making good

62 Providing and fixing S.W. gully trap with C.I. 8.00 No. 1246.92

grating brick masonry chamber and water

tight C.I. cover with frame of 300mm x 300mm

size (inside) with standard weight. (B)

150mm x 100mm size Pof R type

63 Providing and fixing 15mm dia Brass 16.00 No. 186.83

chromium plated screw down bib taps.

64 Providing and fixing granite slab partition 2.00 Sqm. 3040.10

(18mm thick) incl. making in groove in wall and

fixed with cement mortar 1:3 (1-cement : 3-

coarse sand and jointed with grey cement

slurry including polishing both side with single

pieces as per size of partition and moulding

the edge etc. complete.

65 Providing and fixing special type wash basin 3.00 No. 7838.61

on counter top of size 610x460mm or as

required on site of CERA or equivalent quality

including pillar tap, Stop cock etc. complete.

66 Providing and fixing wash down water closet 2.00 No. 11070.61

(European type Wall hung) Jaquar Vignette

wall hung size of 615 x 400 x 363mm with

Hydraulic seat cover with inlet & outlet gasket,

CI chair brackets including concealed type

Metropole flush valve 40mm concealed body

100mm square plate of Jaquar or equivalent

quality with Health flow set etc. complete.

67 Providing and fixing Jaquar Flat back long 3.00 No. 11498.85

pattern stall type urinal size of 315 x 375 x

620mm of approved quality including auto

closing urinal flush valve with wall flange and

connecting inlet connection and waste

coupline and concealed waste pipe etc comp

9 of 28 DTP of ITI workshop at Lalpur 01-26

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

68 Providing erecting and fixing Tripal layer ISI 5000.00 Lit. 12.12

water tank of required capacity each with all

necessary fittings , tank cover and as required

connection etc. complete on terrace

69 Providing and fixing 5mm thick glass mirror 6.00 Sqm. 2544.19

machine cut belveled edge mounted on wall

with special type wall touch SS mirror bracket

fixing with necessary plugs.

70 Providing and fixing C.P. brass towel rail 2.00 No. 616.42

comlete with C.P. brass brackets fixed to

wooden plugs with C.P. brass scews.(B)

600mm x 20mm size.

71 Providing and fixing 600mm x 120mm glass 2.00 No. 557.48

shelf with C.P. brass bracket and guard rail

complete mixed to wooden plug with C.P.

72 Providing and fixing 15mm dia brass screw 20.00 No. 205.83

73 Providing and fixing 25mm dia gun metal 2.00 No. 420.63

check or non return fullway wheel valve.

74 Providing and fixing 40mm dia gun metal 2.00 No. 663.43

check or non return fullway wheel valve.

75 Providing laying and jointing in true line and 20.00 Rmt. 195.67

level 50mm dia. U.P.V.C. Pipe ( SCH- 40) for

cold water including fittings as approved by

Engineer In Charge. Pipe shall be fixed on the

wall with the help of clamp at every two metre

C/C or shall be concealed as directed

including necessary fittings etc. including

testing of pipe and joints and fixing the same

with adhesive solvent, including cost of all

76 Providing,laying and jointing in true line and 64.00 Rmt. 897.79

level 110 diametre U.P.V.C. 9 Type - B )

conferming to IS 13592-1992 with one end

plain and other end socked with rubber ring, &

fitting conferming to ISI 14735-1999 pf

approved make for drainage system pope line,

pipe shall be jointed with each other with

rubber lubricant, pipe shall be fixed on wall

using of PVC clamp of the size 110 mm

diameter x 210 mm length x 196mm heigh at

every 200 mm center to center or shall be

concealed in walls as directed including

necessary fittings such as bends, shoes, etc.

including testing of pipes and joints and

jointed with adhesive solvent cement including

cost of all materials.

77 Providing and fixing in position PVC cowel vent 1.00 No. 101.00

to pipes 100mm dia.

10 of 28 DTP of ITI workshop at Lalpur 01-26

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

78 Providing,laying and jointing in true line and 50.00 Rmt. 834.38

level 160 diametre U.P.V.C. 9 Type - B )

conferming to IS 13592-1992 with one end

plain and other end socked with rubber ring, &

fitting conferming to ISI 14735-1999 pf

approved make for drainage system pope line,

pipe shall be jointed with each other with

rubber lubricant, pipe shall be fixed on wall

using of PVC clamp of the size 160 mm

diameter x 210 mm length x 196mm heigh at

every 200 mm center to center or shall be

concealed in walls as directed including

necessary fittings such as bends, shoes, etc.

including testing of pipes and joints and

jointed with adhesive solvent cement including

cost of all materials.

79 Constructing masonry chamber for under 6.00 No. 3175.32

ground C.I, Inspection chamberand bends

with brick having crushing strength not less

than 35Kg./Sqm in C.M. 1:5 C.I. cover with

frame (light duty) 455mm x 610mm internal

dimensions total weight of cover not less than

35Kg(Weight of cover 23 Kg. and weight of

frame 12Kg) with R.C.C. top slab with 1:2:4

mix foundation concrete 1;5:10 inside plaster

15mm thick with C.M. 1:3 finished smooth with

floating coat of neat cement slurry on walls

and bed concrete etc. comp. (A) Inside

dimensions 455 x 610 and 650mm deep.

80 SIGNAGES ON WALL 10.00 No. 1010.00

Providing, Fabricating & Fixing wall signage's

using 304 grade Stainless steel brushed steel

finish plate of 1.5 mm thick fixed on a wall

using s.s studs including punched (laser cut)

lettering carried out on s.s plate of required

size and text as directed by Engineer over the

S.S plate etc.complete. Size: 18" x 6"

81 SIGNAGES ON Door 10.00 No. 656.50

Providing, Fabricating & Fixing 304 grade

Stainless steel 1.5 mm thick brushed steel

finish plate fixed on a door using s.s studs and

with punched(laser cut) lettering carried out

on s.s plate of required size and text as

directed by Engineer etc. complete. Size: 12" x

82 Providing and fixing MS Ladder of required 180.00 Kg. 116.15

pattern with MS flats(30x3mm) or round or

square bars (12mm) at required spacing &

with round headed bolts and nuts or screws or

welding including primer coat of approved

quality and two coats of oil paintas as

directed by engineer in charge.

11 of 28 DTP of ITI workshop at Lalpur 01-26

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

83 Providing and fixing footed 25mm dia. 4.00 Rmt. 593.88

stainless steel curtain pipe including

decorative S.S. brackets etc. comp.

84 Providing and fixing eco-friendly light weight 29.00 Sqm. 1674.15

calcium silicate false ceiling tiles having

Tegular edge & 15 mm Thick Densified edges

on the Tile Periphery for Extra Strength The

Light weight calcium silicate ceiling tiles shall

have , light reflection 85% non-combustible as

per B.S. 476 part IV, 100% humidity resistance

and also having thermal conductivity0.043°

w/m KC.for the best thermal Insulation . The

Light weight calcium Silicate tile shall be of

approved texture Fine fissured/

Spintone/Cosmos having NRC value of 0.5 &

Globe having NRC value of 0.75 NRC or

equivalent of size 595 X 595 mm to be laid on

true horizontal level suspended inter locking

metal grid of hot dipped galvanized steel

sections (galvanizing @120 grams per sqm

including both side) consisting of main ‘T’

runner suitably spaced at joints to get

required length and size of 24X38mm made

from 0.30 mm thick (minimum) sheet, 1200mm

centre to centre, and cross ‘T’ of size

24X28mm made out of 0.33mm (Minimum)

sheet spaced 1200mm along spaced between

main ‘T’ at 600mm centre to centre to form

agrid of 1200X600mm and secondary cross ’T’

of length 600mm and size 24x28mm made of

0.30 mm thick (Minimum) sheet to be

interlocked at middle of the 1200X600mm

panel to form grid of size 600X600mm resting

on periphery walls/partitions on a perimeter

wall angle pre-coated steel of size

85 Construction of Septic Tank of size 3.50 x 2.00 1.00 No. 47954.80

x 1.80 including excavation , BBCC, RCC,

Reinforcement , Brick Masnory , finished by

15mm plaster in cement mortar (1:3) etc

complete as per drawing.

86 Providing and installing 50 LPH RO Water cum 2.00 No. 46460.00

purifier Plant of (purifying Standard as per

WHO) EUREKA FORBES or Equivalent

Company with Level Monitoring System with

installation and necessary accessories etc

complete as directed.

87 Providing sock pit of 5.00 Cu.M. Volume 2.00 No. 3222.29

including excavating and filling brickbats with

dry masonry work at top for 45cm. height

including covering the top with stone including

providing vatas in C.M. 1:3 with finishing

curing etc. complete as directed.

12 of 28 DTP of ITI workshop at Lalpur 01-26

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

88 Supply & Installing of ABC Type - 6 Kg, 9.00 No. 2141.20

Capacity Fire Extinguisher as per IS -2171 ISI -

mark , with necessary Fittings etc.

89 Supply & Installing of Gas Co2 Type–4.5 Kg.. 9.00 No. 5151.00

Capacity Fire Extinguisher as per IS And ISI -

mark , with necessary Fittings etc.

90 Providing and laying compacted W.B.M. 49.00 Cum. 1246.34

150mm thick of grade-II in two layers each of

75mm thick of machine crushed BT metal of

size 40mm to 63mm with using 13% stone

screenings of 13.2mm size and 7% stone dust

as filler including spreading watering and

consolidation by vibratory roller etc. comp. in

91 Providing and casting in situ controlled trimix 65.00 Cum. 7070.00

cement concrete M-250 for average 200mm

thick road work laid as directed including

adding super platisizer admixture of IS make

and providing and laying M.S. side rail of road

thickness with necessary nut bolts plates

fixing as per width applying plate vibrator

(electric or diesel) on channel compressor

with vacuum dewatering system by using all

necessary equipments and materials and

machinery such as running screed vibrator on

prelaid M.S. channel for leveling ,Vacume

pump, floating and power towelling etc with

filling the joints with bitumen as directed etc

92 Earthwork for embankment including watering 480.00 Cum. 182.14

and consolidation with breaking clods,

dressing with an all lead and lift.

93 Providing and fixing pre-cast concrete kerb 120.00 Rmt. 374.92

stone of gray cement based concrete block

30cm length,30cm height and 15cm thick of

M250 grade concret as per approved design

and including excavation for fixing in proper

line and level,filling the joint with C:M 1:3

(1cement:3fine sand) etc complete.

94 Providing and fixing retro Reflective 2.00 Sqm. 12676.46

Engineering grade Board using C.R.C. (M.S.)

Sheet 2mm, angle iron 75 x 75 x

6mm.Descaling and degreasing the board as

per requirement using epoxyprimer epoxy

paint and carrying retro reflactive process by

screen painting as directed etc. complete

including transporting and fixing in C.C. 1:4:8

with necessary excavation curing etc.

complete as per I.R.C type design. (A)

13 of 28 DTP of ITI workshop at Lalpur 01-26

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

95 Providing & fixing stainless steel (stainless 42.00 No. 2028.08

steel plate of 302 No. ) letter of 45c.m. size

finished with radium sticker including

necessary scaffolding for fixing with epoxy

material etc. comp. as directed by engineer in

charge (Additional Article of Gujarati letter are

consider as a half letter)

96 Providing & fixing stainless steel (stainless 1.00 No. 5342.90

steel plate of 302 No. ) monogram (shinh

stambh) finished with radium sticker of 60cm

size including necessary scaffolding for fixing

with epoxy material etc. comp. as directed by

engineer in charge.

Total Rs of Civil Work :

97 Point wiring for Light / Bell with 2-1.5 sq.mm 43.00 Pts. 410.06

& earth wire of 1.5 sq.mm (Green) both are of

ISI marked 1.1 KV grade FRLS PVC insulated

multi strand copper wires up to 10 mtr length

in below type of pipe erected with 6A Modular

type switch / bell push & accessories and

earth continuity of following type, erected on

PVC / Metallic/Wooden box, single mounting

base frame covered with

textured/metallic/white front plate modules

erected on / in wall / ceiling as per pipe

erected, with necessary Lamp holder/ceiling

rose as directed.(j) in existing pipe erected

concealed in wall/ceiling complete Cat III (Cu

Wire:Polycab,RR Kabel,

Adcab,GreatWhite;Accessories:Legrand,HiFi,

L&K,Wonder,HPL,Indoasian)

98 Point wiring for FAN with 2-1.5 sq.mm & earth 18.00 Pts. 556.51

wire of 1.5 sq.mm (Green) both are of .ISI

marked 1.1 KV Grade FRLS PVC insulated

multi strand copper wires up to 10 mtr length,

in below type of pipe erected with 6A Modular

type switch and hum free EME step type

electronic fan regulator mounted and

accessories with earth continuity of following

type erected on PVC / Metallic/Wooden box,

single mounting base frame covered with

textured/metallic/white front plate modules

erected on / in wall / ceiling as per pipe

erected. with necessary ceiling rose as

directed.(j) in existing pipe erected concealed

in wall/ceiling complete Cat III

(Cu Wire:Polycab,RR Kabel,

Adcab,GreatWhite;Accessories:Legrand,HiFi,

L&K,Wonder,HPL,Indoasian)

14 of 28 DTP of ITI workshop at Lalpur 01-26

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

99 Point wiring for on board Looped Plug with 6A 13.00 Pts. 257.55

Modular type switch & 5 pin socket erected on

PVC / Metallic/Wooden box, single mounting

base frame covered with textured /

metallic/white front plate modules erected on

/ in wall / ceiling with following type

accessories cat-III

(Accessories:Legrand,HiFi,L&K,Wonder,HPL,I

100 (9) 16 Amp. SP one way switch Cat-III 2.00 Nos. 180.79

(Accessories:Legrand,HiFi,L&K,Wonder,HPL,I

101 (10) 6/16Amp. Universal socket cat-III 2.00 Nos. 199.98

(Accessories:Legrand,HiFi,L&K,Wonder,HPL,I

102 Providing and erecting ISI mark Medium class 610.00 Mtrs. 24.24

RIGID PVC PIPES of following size complete to

be erected on/in wall or ceiling erected with

necessary PVC fittings & Junction boxes fixed

with adhesive solution & Clamps with following

dia of pipes, in approved manner as directed

(Make:Nihir,Vraj, Polycab,

Precision,GreatWhite)

(Make:Nihir,Vraj, Polycab,

Precision,GreatWhite)

104 Providing and erecting Mains with 1.1 KV 70.00 Mtrs. 46.46

grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following

type of pipe to be erected concealed in

/flushed on wall/ceiling, with 1.5 sq. mm

copper conductor FRLS PVC insulated

stranded wire of green colour for earth

continuity of following size (E) in existing pipe

(a) 2 wire 1.5 sq. mm

(Make:Polycab,RR Kabel, Adcab,GreatWhite)

105 (E) in existing pipe (b) 2 wire 2.5 sq. mm 304.00 Mtrs. 62.62

(Make:Polycab,RR Kabel, Adcab,GreatWhite)

106 providing and erecting Mains with 1.1 KV 290.00 Mtrs. 240.38

grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following

type of pipe to be erected in / on wall / ceiling

with 2.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for

earth continuity of following size (E) in existing

pipe(h) 4 wire 6 sq. mm

(Make:Polycab,RR Kabel, Adcab,GreatWhite)

15 of 28 DTP of ITI workshop at Lalpur 01-26

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

107 providing and erecting Mains with ISI marked, 4.00 Mtrs. 12.12

1.5KV grade electrolyte multi stranded,

annealed copper conductor with heat

resistant PVC insulated conforms to IS

IEC - 227 erected in existing pipe of following

size (Specifically for control panel, relays,

power switchgears, motor starters & control

wiring) with required size of copper lugs, nuts

and bolts if required. (a) One wire 1.00 sq. mm

108 (e) One wire 6.00 sq. mm 120.00 Mtrs. 56.56

109 (i) One wire 35.00 sq. mm 2.00 Mtrs. 300.98

110 Supplying and erecting Flexible PVC insulated 42.00 Mtrs. 46.46

multi strand multi core 1.1 kv grade ISI marked

copper wires of following size to be erected as

directed.(e) 1.50 Sq.mm 3 core round PVC

(Make:Polycab, RR Kabel,Adcab,GreatWhite)

111 Providing & erecting Switch board for 5.00 Nos. 1133.22

Computer or electric apparatus consisting of

following modular type accessories mounted

with PVC / Metallic concealed/open box with

single mounting base frame covered with

textured/metallic /white front plate,modules

erected with necessary connections as

directed 1 no. 6A/16A universal plug-switch

combined. 3 nos. 6A Switch 3 nos. 6A 5 pin

Plug For Modular Type Accessories Cat III

(Accessories:Legrand,HiFi,L&K,Wonder,HPL,I

112 Providing & erecting insulated socket 3P+N+E 28.00 Nos. 2190.69

with Plug 32A rating which is comprised of

Four pole MCB slot and insulated socket IP40

16 of 28 DTP of ITI workshop at Lalpur 01-26

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

113 Supplying and erecting LED indoor fittings 35.00 Nos. 535.30

with LEDs of wattage 0.2 Watt to 0.5 Watt

assembled on single MCPCB, with housing

used as a heat sink shall be made of thick

sheet Steel conforming to IS: 513/CRCA/

aluminium die cast powder coated and high

U.V. & corrosion resistance with diffuser with

company mark/name 160V to 270V, Power

Factor more than 0.95, THD < 15%,

CCT 3000 K to 6500K, Luminaire efficacy>

lumens/watt ,LED LED driver efficiency > 85 %

( fitting required LM-79 & LM-80

Certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any

wattage capacity between the ranges

shown.)(A) Tube Light with integral driver (v)

40 Watts, Surge-2 KV, IP-20, conventional

(Make:Jaquar,Wipro,Crompton,Havells,Bajaj)

114 Supplying and erecting LED indoor fittings 6.00 Nos. 758.51

with LEDs of wattage 0.2 Watt to 0.5 Watt

assembled on single MCPCB, with housing

used as a heat sink shall be made of thick

sheet Steel conforming to IS:

513/CRCA/aluminium pressure die cast

powder coated and high U.V. & corrosion

resistance with diffuser housed in aluminium

casted body with company mark/name 160V to

270V,Power Factor more than 0.95, THD <

%,CCT 3000 K to 6500K, Luminaire efficacy>

85 lumens/watt ,LED driver efficiency > 85 %

(fitting required LM-79 & LM-80

Certificates(NOTE: Below description have

shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any

wattage capacity between the ranges

shown.)(A) Square/ Circular shaped

Surface/Recessed Mount Downlight with

provision for spring loaded mounting clips

complete.IP20 (iv) 22-24 watts, Surge-2 KV Cat

(Make:Jaquar,Wipro,Crompton,Havells,Bajaj)

17 of 28 DTP of ITI workshop at Lalpur 01-26

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

115 Supplying and erecting LED street light / Flood 8.00 Nos. 5976.17

light fittings with High power White LEDs

wattage of 3 Watt and above assembled on

single MCPCB, efficiency more than 130 lm/w

and corrosion free High pressure die cast

aluminum housing with smooth finish powder

coated and heat sink extruded aluminium with

diffuser and Polycarbonate optics/ lenses,

with toughened glass with company

mark/name engraved or embossed 160 to

V,Power Factor more than 0.95, THD < 10 %,

CCT 3000 K to 5700K,Uniformity ratio >0.45,

Luminaire efficacy> 100 lumens/watt . LED

driver efficiency > 85 %.( fittings required LM-

79 & LM-80 certificates)(NOTE: Below

description have shown ranges of Wattage

capacity of LED fittings.The Engineer incharge

may select any wattage capacity between the

ranges shown.) (A) Street Light (IP-65), Surge

protection -4KV integral and ,Light must have

440VAC line supply with over-voltage

protection.(iii) 90 watts Cat III

(Make:Jaquar,Wipro,Crompton,Havells,Bajaj)

116 (B) Flood Light (IP-65), Surge protection -4KV 7.00 Nos. 8453.70

integral and ,Light must have 440VAC line

supply with over-voltage protection.(v) above

150 to 160 watts Cat III

(Make:Jaquar,Wipro,Crompton,Havells,Bajaj)

117 Providing and erecting Approved make Four 1.00 Nos. 6173.12

pole moulded case circuit breaker having

breaking capacity ICU of 25 KA. at

V,having normal current rating up to 100A.

with Fixed thermal & magnetic release suitable

to work on A.C. supply 50 c/s. with all internal

connections, spreader tinned copper &

complete erected in existing 16 G.M.S.

housing.ICS=100% of ICU only Cat III

(Make:Schneider, Siemens, L & K,ABB,C&S)

18 of 28 DTP of ITI workshop at Lalpur 01-26

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

118 Providing and erecting Approved make Four 2.00 Nos. 6790.43

pole moulded case circuit breaker having

breaking capacity ICU of 25 KA. at

V,having normal current rating up to 100A.

with Fixed thermal & magnetic release suitable

to work on A.C. supply 50 c/s. with all internal

connections, spreader tinned copper &

complete erected in existing 16 G.M.S.

housing.ICS=100% of ICU only Cat III Note:-1

Add Rs. 10% extra for housing/Encloser of

MCCB for Item No 3-4-1 to 3-4-12 (The

Enclosures should be used of same company

of MCCBs to be used)

(Make:Schneider, Siemens, L & K,ABB,C&S)

119 Providing and erecting Approved make Earth 1.00 Nos. 4687.41

fault Relay suitable to mount with inter

connection suitable to following size of

moulded case circuit breaker having CT ratio

& MCCB rating as following along with shunt

trip 220V AC. with all internal connections &

complete erected in existing M.S.housing.

(1)100 A , CT Ratio 1/100

(Make:Schneider, Siemens, L & K,ABB,C&S)

120 Supplying and erecting triple pole & neutral 0.50 Rn. 1961.42

440V / 500V panel mounting Copper Busbars Mtrs

with four equal Nos. of electrolyte bus having

current density not more than 1.6 Amp. /

sq.mm (Rated current / cross section area)

duly wrapped with colour insulating tape for

phase sequence of following current carrying

capacity, erected with necessary bus bar

supports /insulators, main cable socket to

each bar, erected in existing cubical panel

with necessary connections. (A) Suitable for

100 Amp. Capacity

121 providing and erecting Miniature circuit 15.00 Nos. 270.68

breaker single pole 2A system and having

breaking capacity 10 KA to be erected in

existing box. confirming to IS 8828/1996 with

ISI Mark Cat III

(Make:Schneider, Siemens, L & K,ABB,C&S)

122 providing and erecting Miniature circuit 12.00 Nos. 112.11

breaker single pole 16 A to 25A suitable to

operate on 240 V A.C. system and having

breaking capacity 10 KA to be erected in

existing box. confirming to IS 8828/1996 with

ISI Mark cat-III

(Make:Schneider, Siemens, L & K,ABB,C&S)

19 of 28 DTP of ITI workshop at Lalpur 01-26

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

123 Providing & erecting 240 V MCB double pole 2.00 Nos. 295.93

switch for lighting Load (B Curve) having

KA breaking capacity & confirms to IS :

in existing box having following capacity (B)

(Make:Schneider, Siemens, L & K,ABB,C&S)

124 Providing & erecting 415V MCB Four Pole 4.00 Nos. 638.32

Switch for Lighting Load (B curve) having

10KA breaking capacity & confirms to IS :8828

in existing box having following capacity (b)40

(Make:Schneider, Siemens, L & K,ABB,C&S)

125 Providing & erecting 415 V MCB Four Pole for 45.00 Nos. 595.90

Motor & Inductive Load (C Curve) having

10KA breaking capacity & confirms to IS :8828

in existing box having following capacity (a)

(Make:Schneider, Siemens, L & K,ABB,C&S)

126 Sheets steel powder coated enclosure 1.00 Nos. 176.75

suitable for incorporating One/Two nos. MCB.

127 Providing and erecting Sheet Steel powder 1.00 Nos. 629.23

coated MCB distribution board - flush / surface

mounted fitted with busbar, neutral link, earth

bar and DIN rail, Conforms to IS 8623-1 &

IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be

used of same company of MCB to be used)

suitable for (A) single phase incoming and

horizontal single phase outgoing (b) sheet

steel double door (IP-43)(i)4 way

(Make:Schneider, Siemens, L & K,ABB,C&S)

128 (B) three phase incoming and single phase 1.00 Nos. 2339.16

horizontal type outgoing Per phase isolation

type (PPI) (b) sheet steel double door (i)4 way

(Make:Schneider, Siemens, L & K,ABB,C&S)

129 providing and erecting Approved make 4.00 Nos. 2235.13

RCCBs conforming to IS: 12640 and having

sensitivity of 30 mA and Short Circuit

withstand capacity of 10 KA and suitable for

operation on single phase 240 V,50Hz. having

characteristic of quick action & tripping with

all advance feature & do not incorporate any

electronic component. for following Max.

rating erected as directed (ii) 40Amps. DP

(Make:Schneider, Siemens, L & K,ABB,C&S)

20 of 28 DTP of ITI workshop at Lalpur 01-26

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

130 Providing and erecting metallic vitrified 1.00 Nos. 69.69

danger notice board as per language

suggested by engineer incharge for MEDIUM

VOLTAGE installation to be erected as per IS-

131 Providing and erecting Annealed bare Copper 2.00 Kgs 794.87

wire 8 to 16 SWG..

132 Supplying & erecting earth pit of minimum 1.00 Nos. 4591.46

bore dia.150mm size approved make Earthing

Electrode consisting Pipe-in-Pipe Technology

as per IS 3043-1987 made of corrosion free

hot dipped G.I.Pipes having Outer pipe dia of

50mm having 80-200 Micron galvanising, Inner

pipe dia of 25 mm having 200-250 Micron

galvanising, connection terminal dia of 12mm

with constant ohmic value surrounded by

highly conductive compound with high charge

dissipation suitable for following type of

applications with chamber and heavy duty

cover. (A)(approved make OEM has to submit

test certificate including value of earth

resistance of installation duly stamped and

signed by agency and officer Incharge has to

ensure the value of earthing resistane

mentioned in test Certificate) & having back

filling compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 ohm / meter

testing as per IEC 62561-2017, Voltage drop:-

< 1 volt at no load & dry form, Sulphar content:-

<2%(C) Back fill Compound :- Earthing

compound should be capable to retain

moisture for long time Necessary test report

must be submitted by Agency. (a) For

Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

(Make:Vasundhara, Saraa, National,Electro

21 of 28 DTP of ITI workshop at Lalpur 01-26

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

133 Providing & erecting weather proof, dust & 1.30 Sq. 14902.55

vermin proof, floor mounted front operated Mtrs

indoor type cubical panel board necessary IP-

42 and above protection as per approval from

engineer incharge made from 14 SWG thick

CRC M.S. sheet for outer body & doors,

SWG thick CRC M.S.sheet for internal

partitions with necessary accesories

supporting angles/ flats channel including

cutting, bending, drilling, welding, riveting

with internal partitions & cable alley as per

requirements & instruction of engineer-in-

charge with erection of supplied switch gears,

BUSBARS, suitable size of inter connecting

PVC copper wire / copper-aluminium strips,

rubber grommets, rib, bakelite control

fuses/MCB for measuring instruments, earth

bus & earth bolts, foundation flange - bolts-

base Plates, sufficient nos. of hinged doors,

handles with locking arrangement and rubber

gasket, heavy duty end terminal connection,

danger notice board,necessary

ventilation,earthing strip complete. The Panel

shall be painted with epoxy powder coating.

(The rates excludes the cost of switchgears,

bus bars, inter connecting mains & Copper

Aluminium strips, meters, Fuses etc. The

dimension shall be measured excluding base

beams) The panel shall be supplied with

following approved manufacturers with

following size. (B) The standard companies

switch gear shall be used and only

134 Providing , erecting , fabricating the M.S. 30.00 Kgs 77.77

structure as per requirement on site

incorporating proper size of M.S.

angles,square,round, flats, bars, channels,

sections complete with cutting, welding,

grinding & finishing duly painted with one coat

of red oxide with erection on site as per

direction of engineer in charge with necessary

grouting, cementing, plastering & finishing

135 Providing and erecting XLPE(IS:7098)(I)-88 ISI 60.00 Mtrs. 284.82

armoured cable multistrand Aluminium

conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe

of following size of cables (C) 3 1/2 core

Sq. mm ( 25 Sq.1/2 mm core)

(Make:Polycab, RR Kabel,Adcab,GreatWhite)

22 of 28 DTP of ITI workshop at Lalpur 01-26

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

136 Providing and erecting XLPE (IS:7098)(I)-88 ISI 194.00 Mtrs. 126.25

armoured cable multistrand / Solid Aluminium

conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe

of following size of cables (B) 4 core 6 Sq. mm

(Make:Polycab, RR Kabel,Adcab,GreatWhite)

137 Making trench in soft soil of suitable width of 125.00 Mtrs. 55.55

90 cm deep for laying cable or locating the

fault all over the run and back filling the same

and making the surface as normal ground.

138 Making trench in Hard Murrum / Tar Road of 90.00 Mtrs. 74.74

suitable width of 90 cm or required depth for

laying any size of cable or locating the fault all

over the run and back filling the same and

making the surface as normal ground.

139 Supplying following size of Light duty “A” 20.00 Mtrs. 300.98

Class G.I . Pipe & erecting as directed by

Engineer-in-charge. (B) 50 mm dia

140 Providing & laying approved make Double 159.00 Mtrs. 62.62

walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with

necessary connecting accessories of same

material at required depth in existing trench

for laying of cable. below ground / road

surface for enclosing cable (A) 50 mm outer

141 Providing and, fixing heavy duty flange type 15.00 Nos. 38.38

brass cable gland with rubber ring for PVC

insulated armoured cable complete with out

going tails, insulating tape etc for following

size of cables. (B) 4 core 6 Sq. mm

142 Providing and, fixing heavy duty flange type 6.00 Nos. 75.75

brass double compression type cable gland

with rubber ring for PVC insulated armoured

cable complete with out going tails, insulating

tape etc for following size of cables.(B) 3 & 1/2

core 35/50 Sq. Mm

143 Solder less crimping type Aluminium lugs 6.00 Nos. 15.15

conforming to IS suitable for cable of following

size evenly crimped with high pressure tool &

connected to switchgear terminals with

brass/cadmium plated nut bolts in an

approved manner. (C) 25 Sq.mm.

23 of 28 DTP of ITI workshop at Lalpur 01-26

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

145 Providing & erecting Approved make Power 18.00 Nos. 1948.29

Saving 50 Watt Ceiling Fan with double ball

bearing ISI mark with Condenser 230 volt A.C.

50 Hz 1200 mm sweep complete having

3blades with aluminium blades with , canopy &

30 cm. down rod erected with earthing.

(Make:Crompton, Havells, Bajaj,GM,Usha)

146 Supplying and erecting 19 / 20 mm. nominal 18.00 Mtrs. 108.07

bore Medium Class M.S. Pipe down rod

erected duly painted for fan complete with

proper insulation without leakage and

Supplying & erecting fan hook box of 10 mm 18.00 Nos. 108.07

M.S. round bar bounded to the RCC bars up to

50mm length each side and pierced through a

16 Gauge M.S. box / Heavy Duty PVC box

complete erected concealed in Ceiling with

necessary finishing.

148 Providing 2.5mm.thick laminated acrylic sheet 18.00 Nos. 18.18

to cover the fan hook or Fan box.

149 Supplying & erecting approved make low 2.00 Nos. 1703.87

noise decorative exhaust fan having square

frame ABS body with inbuilt lowers & square

frame. 200mm with 1350RPM Cat.II

(Make:Crompton, Havells, Bajaj,GM,Usha)

24 of 28 DTP of ITI workshop at Lalpur 01-26

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

150 Supply of approved make FRP Pole having 4.00 Nos. 14894.47

following specifications: FRP Light Pole made by

CNC filament winding machine using thermoset

resin polyester/epoxy resin system) having

minimum 62% glass content. The pole should be in

one piece and tapered round in shape, having

smooth finish and should be totally free from

corrosion as well as non conductive & shock proof

Pole should be provided with FRP Anchor Base and

it should be heavy duty, or MS Material duly painted

with Epoxy paint.Pole should be flame retardant as

per IS 6746. Resin used shall be UV resistance and

pigmented. A highly weather resistant

polyurethane coating shall be applied to the pole

after applying suitable primer system that ensures

proper adhesion of the paint. Minimum coating

thickness shall be 80 to 100 micron. Deflection of

the pole shall not exceed more than 10% of the

length of pole for the given load“ Pole should be

generally made as per the dimensional data,

performance criteria and some interchangeability

features of poles as per standard ANSI C

latest version or ASTM D 4923/01 including cable

termination box with necessary accessories . The

size of pole and type of installation with foundation

as per manufacturer details and site requirement

are as below.(2) Suitable for base plate mounting

Double arm Bracket.[C] Overall length of 6 Mtr.

Average Thickness: 8mm. Top/ Bottom OD Dia A/F

114/174 mm ± 2mm approx. approx. Weight of Pole

38 kg approx. (Without Base) Anchor Base (Size

(Make:Bajaj,Swastik,Ambica,Jetcotech)

151 Providing FRP arm bracket of having 2 sets of 4.00 Nos. 3933.95

suitable SS304 hardware for fixing the

brackets & spread of 1.2 Mtr(Suitable for 89 to

114 mm pole top dia)(B) Double arm bracket

152 Supplying & erecting approved make SMC 7.00 Nos. 476.72

press moulded composite FRP. loop-in, loop-

out approx. 2mm thick box complete with

Bakelite connector strip 5way(3P+N+E),DIN

rail for mounting mob & hinged doors as per

requirement having locking arrangements

with mounting clamp with nuts, bolts &

washers suitable for erection on pole with

cable clamps& earth bolt of following size of

box.(C)150mm x 125mm x 100mm [deep]

(Make:National,EPP,Sintex)

25 of 28 DTP of ITI workshop at Lalpur 01-26

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

153 Providing & erecting water cooler having 1.00 Nos. 55893.40

storage capacity 150 Ltr. & cooling capacity

150 Ltr.per hour @ an ambient temp of 45˚ C.

The outlet temp. of the water should drop by

15˚C within a hour, The water cooler should be

comprising of hermetically sealed

compressor, fan motor, condensing unit,

water tank surrounded by evaporating, coil,

thermostats, relay etc.complete with

necessary inlet & outlet connection. The body

of water cooler will be made from Stainless

(Make:Voltas, Usha, Bluestar)

154 Supplying & erecting 5 stage single reverse 1.00 Nos. 29187.99

osmosis water purification system with M.S.

powder coated frame, prefilter housing with

'O' ring presediment filter GAC filter, carbon

filter suitable buster DC pump capacity 80 psi,

mention with 40 psi inline type post carbon

filter auto low & high pressure switches with

following size of storage tank & LPH capacity

& erected as directed [C] 50 Ltr / Hr with

psi 2 nos booster pump

155 Providing & Erecting new water level Sensor 1.00 Nos. 864.56

for 50 Ltr. R.O. System

156 Supplying and erecting approved make panel 1.00 Nos. 1275.63

mounting type Digital Voltmeter having

digits LED display, 0 to 750 AC Volts range

erected on existing panel board with all

connection, wiring etc .with manufacturers

calibration certificate.

157 Supplying and erecting approved make panel 1.00 Nos. 1558.43

mounting type Digital Ammeter having

digits LED display, external CT operated,

calibrated for 0 to 1000 Amps suitable to

operate on 500 Volt AC , erected on existing

panel board with all connection, wiring etc

.with manufacturers calibration certificate.

158 Supplying and erecting Ammeter / Voltmeter 2.00 Nos. 317.14

selector switch for 3 phase AC Supply 500 V

on existing panel board with necessary

159 Providing & erecting L.T. Current 3.00 Nos. 274.72

Transformer with bar primary 50/5 to 1000/5

ratio 15 VA burden erected in existing CRCA

box duly secured with insulating materials

connected to the meter

26 of 28 DTP of ITI workshop at Lalpur 01-26

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

160 Supplying and erecting approved make 3.00 Nos. 43.43

suitable panel indicator LED type lamp, lens

cover, complete erected with necessary

Total Rs of Ele Work :

Total Rs.of Ele & Civil work

Amount of my tender work out as under

I / We am/are willing to carry out the work at ………………………………………….. % above / below

Percent [should be written in figures and words] of the estimated rates mantioned above. Amount

of my/our tender works out as under

Estimated Amount Put to tender: Estimated Amount Put to tender:

Deduct % below Add % above

Net Rs. Net Rs.

In words : In words :

Signature of Contractor

Deputy Executive Engineer Executive Engineer

Jamjodhhpur (R&B) Sub Division Jamnagar (R & B) Division,

Jamnagar. Jamnagar.

27 of 28 DTP of ITI workshop at Lalpur 01-26

Sr. Description of Item (With brief Quantity Unit Rs. In Amount

No. specification and reference to book of figure

specifications)

1) The work shall be carried out as per Public Works Department Hand Book, I.S.

Specification and other specification of the Division or as Directed.

2) All the columns in Schedule should be filled in INK and the total of the entries in the last

column should be strike out by the Contractor under his Signature.

3) Rates should include clearance of site (Prior to commencement of work and its close) in all

respect and good for work under all conditions of site moisture weather etc.

4) The Contractor shall exhibit the details of works, Tenders amount and specification as per

Govt. Circular No. TD 32772 N. Dt. 26-4-78 and as per G.R. No. TNC-9-24-C, Dt. 18-11-91,

as directed by Engineer-in-Charge of the works, on board at site of the work.

5) Contractor shall even "NIL" percentage, if no deduction is offered.

6) Testing of materials shall be as per statement attached with the specification. The

material shall be tested in GERI Bill for the testing shall be paid by the Executive Engineer

and 1% of amount put to tender after deducting the cost of materials to be supplied by

Department as per SCHEDULE 'A' at the sanctioned estimate rates from the Contractor in

Running Bills. (As per G.R.No. (R&B) TNC-1085/4/C Dt. 20-12-91 and modified ide (R&B)

Deptt. Circular No. SSR/10000092-IB-12910-C Dt. 16-10-95)

7) For R.C.C. Item where there is change of grade mix or charge as per actual mix design the

difference of cement consumption shall be deducted from rate of original item at the rate

of star rate mentioned in the tender.

8) 1% L.C. shall be deducted from the bill as per agreement.

Signature of Contractor

Deputy Executive Engineer Executive Engineer

Jamjodhhpur (R&B) Sub Division Jamnagar (R & B) Division,

Jamnagar. Jamnagar.

28 of 28 DTP of ITI workshop at Lalpur 01-26