SPL REPAIR TO SHELTER NO T-50/1 AND T-48/2 AT NAGTALAO UNDER GE BANAR

Amount

Demolition of Cement concrete in ground floors and pavings n.exc 15 cm thickness below or above ground level) and removing debris out of MOD land complete all as specified.

M&L for 25 mm thick cement concrete type B-1 1:2:4 (using 20mm graded crushed stone aggregate) to receive floor finishes etc complete all as specified.

M&L for 18-20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified.

M&L of 20-25mm thick machine cut KOTA stone slab as in shelves (Single piece) fixed in walls machine cut, laid over cement and jointed with grey cement slurry with pigment to match the shade of the slab, incl rubbing and Mirror polishing complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding complete all as specified.

M&L for coloured glazed ceramic tiles 300mmx450mmx6mmthick as per IS 13712 Grade II(a) over and including 10mm thick rendering in CM (1:4) set and jointed in neat cement slurry and pointed with colour cement to match on vertical stone masonry surfaces as in dado complete all as specified.

M&L for Virified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including 15mm thick screed bed in CM (1:6) complete all as specified.

All item as per Ser No 7.00 above but as in skirting including 10mm thick backing coat in CM 1:4 on concrete surfaces .

M&L for 15mm thick rendering in CM 1:6 on stone masonry finished even and smooth without using extra cement complete all as specified.

Preparation of old unplastered or new surfaces of wall & Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified.

M&L 3mm thick wall care putty on wall for new/old surface , sand papering the same & making good to depressions if any to obtain totally smooth surfaces complete all as specified.

M&L for two coats of oil bound distemper of one or different tints on new surfaces of walls including preparing of plastered surfaces complete all as specified.

M&L for complete removal of existing treatment and applying two coat of oil bound distemper over and including 3mm thick wall care putty all as specified.

Taking down Chowkhat or frame with shutter (without taking out shutter from frame) of area exc 1.5sqm but not exc. 4 Sqm each complete all as specified.

M & L for 35mm thick flush shutters, solid core construction with block board core and veener face fixed on both side of door complete all as specified.

S&F powder coated Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified. (min thickness of powder coating 50 micron)

S&F 5.5mm thick Sheet glass ordinary quality glazing with rubber bidding in square in n. exc 0.5sq.m in each pane sheet glass is ground or obscured or frosted, on one side complete all as specified.

S&F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified.

S&F powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified (minimum thickness of powder coating 50 micron)

Taking down Chowkhat or frame with shutter (without taking out shutter from frame) of area not exc 1.5 sqm each complete all as specified.

S&F PVC door frame wooden finish of size 50mmx 47mm made out of 5mm plain color PVC sheet reinforced with MS square tube complete all as specified.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm Plain colour PVC Sheet on back face complete all as specified.

S &F of Stainless steel butt hinges medium weight, cold rolled of size 100 mm size complete all as specified.

S&F 150 mm long aluminium anodised tower bolt complete all as specified.

S&F 150mm long aluminium anodised handle extruded section complete all as specified.

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified.

Taking up or down 15mm bore steel tubing and connections complete all as specified.

Supply & Fixing 15mm bore GI Tubes, 'medium grade' galvanised,with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified.

Taking up or down 20mm bore steel tubing and connections complete all as specified.

Supply & Fixing 20mm bore GI Tubes, 'medium grade' galvanised,with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified.

S&F fancy type (chromium plated ) bib cock 15mm dia, cast copper alloy screwed for iron pipe or for brass ferrule all as specified.

S&F in repair angular stop valves cast copper alloy chromium plated screwed down high pressure fancy type screwed both ends for 15mm bore of iron pipe or union complete all as directed.

S&F in repair 20 mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repair complete all as directed.

M&L for 75mm outlet diameter UPVC nahani trap, with CP Mild steel grating (with or without hole) including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) using 20mm graded stone aggregate.

S&F decorative type curtain rod stainless steel pipe 22 to 25 mm dia with best quality knob metal with double fitting type including stainless steel brackets fixed to walls complete with two nos decorative stainless steel knobs at each end complete all as specified.

M&L for 7.5cms thick Sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates, etc, n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:3 or cement mortar 1:4, complete

Dismantling of cast iron drain pipes 75/100 mm bore, jointed in cement mortar and taking out of trenches & walls complete all as specified.

Supplying and laying of 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified.(with all fitting)

Supplying and laying of 110 mm dia UPVC pipes SWR & Plain UPVC SDR 11 fittings in trenches complete all as specified. (with all fitting)

Supplying and laying of 75 mm dia UPVC pipes SWR fittings on walls / ceiling or laying in floors complete all as specified. (with all fitting and clamping)

Supplying and laying of 110 mm dia CPVC pipes SWR fittings on walls / ceiling or laying in floors complete all as specified. (with all fitting and clamping)

Dismantling water tanks exc 500 liter and n exc 1000 liter complete all as specified.

S&F rotational moulded polyethylene water storage tank ISI Marked (cylindrical vertical with closed top) white, hoisted and fixed in position all as directed of capacity 1000 ltrs a Including 20mm bore Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0mm-210gms./ 25mm-455gms/ 40mm - 690 gms) complete all as directed.

Supply only integral water proofing compound complete all as specified.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles

M&L for squarred rubble walling Jodhpur type regular coursed well bonded, bedded and solidly hearted built in cement mortar 1:6 complete all as specified.

Extra over squared rubble stone walling Jodhpur type regular course for hammer dressing to face of stone with max depression on face from a straight edge not exc 20mm and dressing

M&L for precast cement concrete solid building blocks type B1 1:2:4 (20mm graded stone aggregate) or slabs 10cm thick (with plain or interlocking joints as directed) setting in 1:4 cement mortar, complete, in walls complete all as specified.

Excavation in trenches not exc 1.50m wide and not exc 1.50m depth and getting out in soft/loose soil ext complete all as specified and directed by Engr -in- Charge.

S&F 150mm Reinforced concrete pipes, class NP2, laid and jointed with collars complete all as specified.

M&L for cement concret (1:3:6) type C-2, using 40mm graded stone aggregate bed to drain pipe 150 mm dia including packing under and hunching against the pipe after they are laid including necessary formwork all as specified.

Returning, filing in including, lelveling,watering and well ramming in layers not exc 25cm thick each complete all as specified.

Removing excavated material to a distance not exc 50m depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed by Engr -in- Charge.

M&L for Machine cut kota stone slab flooring 20-25mm thick over and including 15mm thick cement screed base in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over and including 10mm thick plaster in backing coat on verticle surface in CM 1:4 and jointed complete all as specified.

Excavating in post holes (of similar holes) each n. Exc. 0.50 cum getting out, returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25cm, watering and removing surplus soil to a distance n. Exc. 50m and making good surface complete all as specified.

M&L Cement concrete in foundations, filling and mass-concrete Type B2 1:2:4 (40 mm graded aggregate) complete all as specified.

Dismantling structural steel work in?cluding doors, gates , ramed truss etc. complete all as specified.

M&L Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates Fe 410-W (Gde E-250) quality A complete all as specified.

M&L Preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified.

Dismantaling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified.

S&F Pre-laminated galvatume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

S&F 0.63mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275

Dismantling boarding, any description, fixed in any position with screws complete all as specified.

S&F 18-19 mm thick Fissured board false ceiling system with ULTIMA RH99 board (regular) or equivalent mineral fiber acoustical suspended ceiling system, board size shall be 600mm X 600mm including Anodised aluminium snap grid (powder coated ) frame work for false ceiling all as specified ( Size of grid 605 x 605mm). The aluminium snap grid, tee section, L section , Hooks , wire assembly, anchor fasterners, suspenders shall be Armstrong (Make) or equivalent (a) Size of main Tee & cross Tee -39 X24.7 X 0.80mm (b) Size of wall angle - 22.20 X 22.20X 0.65 mm complete all as specified.

M&L for Framed work as in door or gates of angle ,MS hollow pipes, solid SQ sections Flat iron etc or other section with gusset plates, rails, braces etc complete with steel sheetingas required to br prepared for hanging or sliding with and including MS Channel as posts & hold fasts & suitable arrangements for locking etc complete all as specified & directed conforming to Fe 290.Gde E165.

S&F in repairs galvanised ms wire cloth 0.56mmm nominal dia of wire and average width of aperature 1.18mm complete.

M&L for 25 to 30mm Jodhpur stone cladding gang saw cut with machine cut edges, uniform colour of each stone size exceeding 0.5 sqm area fixed with and including one number SS clamps (grade - 202) of flat-30mm X 2mm, 150mm long made to shape in each slab, making V groove at top and bottom of stone and drilling hole for hold fastener, polishing, rubbing & including silicon treatment.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, sockets, lamp holder and conduit etc. removing materials to store for taking credit and making good disturbed surfaces of walls, floors, etc complete all as specified and directed by EIC. Note:- The damaged surfaces to be made good with plastering & applying colour wash in required coats to matching with existing surfaces as directed by Engineer-in-charge. Cost of the same deem to be included in quoted rates and nothing extra on this account admissible.

M&L Point wiring with 1.5 Sq. mm PVC insulated and unsheathed single core FRLS copper cable 1100 volts grade with Multi-stranded copper conductor in and including PVC casing caping (heavy grade) and accessories fixed on walls/floors/ceilings etc alongwith continuous earth wire 1.5 Sq mm PVC insulated and unsheathed single core FRLS cable 1100 volts grade with stranded copper conductor and connected to common earth dolly. with 3 mm thick PVC box fixed with brass screws etc complete for one light point controlled by one switch, complete all as specified for the following. (a) One light point controlled by one switch.

All item as per Ser No 70.00 above one fan/ exhaust fan point controlled by one switch.

All item as per Ser No 70.00 above one switch socket out let point 5 Amps on independent board

All item as per Ser No 70.00 above one switch socket out let point 5 Amps on same board complete all as specified.

Ditto all as per item No 70.00 herein before but with 4 sqmm cable for one 3 pin 15 Amp switch socket outlet and using 4 sqmm PVC single core copper conductor cable multistranded as earth wire complete all as specified.

Supply and fixing switch piano flush type 5 Amp single pole, one way complete all as specified.

Supply and fixing stepped type electronic fan regulator, resistance type complete all as specified.

Supply and fixing for ceiling rose surface bakelite 65 x 50 mm three terminal complete all as specified.

Supply and fixing switch socket combination multipurpose 5 pin 5 Amp flush type, universal complete all as specified.

Supply and fixing socket outlet 5 pin 5 Amps, flush type complete all as specified.

Supply and fixing switch socket combination multipurpose 5 pin 5/15 Amp flush type, universal complete all as specified.

S&F powder coated sheet metal enclosures MCCB VTPN DB, double door, tripple pole and neutral, 6 way 415 volts fitted with insulated vertical phase bus bar/neutral bar with shround earth bar cement spill proctector interconnecting wire set cable tiesblanking plates and circuit indentificationlables etc all as per IS-8623-1 IK-09

Supply and fixing powder coated sheet metal enclosures DB, double door, single pole and neutral (SPN) 12 way 240 Volt fitted with bus bar, DIN channel, neutral link and incoming contact and making good disturbed surfaces of walls including plaster cutting of wall etc complete all as specified.

Supply and Fixing Panel mounting socket angled 32 Amps 3 Phase with (3P+N+E) completed with on panel with all connection as per site requirement as per complete all as specified.

Supply and fixing MCCB 415V,16KA, 4 Pole 125 Amps Adjustable overload setting & fixed magnetic setting, making good disturbed surfaces of walls including plaster cutting of wall etc complete all as specified.

Supply and fixing 415V 10KA 'B' curve miniature circuit breaker (MCB) TP of 40 A in the DB complete with connection testing and commissioning complete all as specified.

Supply and fixing 240V 10KA 'B' curve miniature circuit breaker (MCB) SPN of 40 A the DB complete with connection testing and commissioning complete all as specified.

Supply and fixing 240 V 10KA 'B' curve miniature circuit breaker (MCB) SP of 5 to 32 A in the DB complete with connection testing and commissioning complete all as specified.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 40 AMP, in the MCB DB Complete with connection testing and commissioning

Supply and laying XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 50 sq. mm 3.5 core, clamped on wall with suitable clamps complete all as specified.

Supply and laying of GI pipe medium Class 40 mm dia for cable protection complete all as specified.

M & L in replacement for Sub main wiring complete with 5 single core 10.0 sqmm, 1100 volts grade, PVC insulated, stranded copper conductor FRLS cable with continuous copper earth conductor of 10.0 sqmm in and including PVC casing caping and accessories complete all as specified. (Note:- (i) Making good of disturbed surfaces will be done by contractor without any claims. (ii) 5 runs of 10 Sqmm conductor, and one run of PVC casing caping shall be measured as one unit length.)

Taking down old and Material and labour for sub main wiring with two single core FRLS PVC insulated unsheathed copper stranded conductor of size 4 Sqmm and one run of size 4 Sqmm for conteneous earthing connected to common earth dolly complete drawing in and including suitable size of In PVC cashing caping with all fittings like tie,bend ,end cap,GI flexible etc and accessories fixed with GI clamp( clamp to clamp distance not exceed 1.2 mtr) clamp properly fixing on wal/ ceiling /trusses/beam as per complete all as specified.

Taking down old fitting and S&F surface mounting batten tube light fitting, integrated polycarbonate LED channel with white acrylic cover complete suitable for and including lamp LED 1x20 Watt,(4 feet) fixed properly on wall surface and connecting complete from ceilling rose to fitting by three core copper conductor cable of overall sheathed size 2.5 Sqmm which shall be passed through PVC flexible conduit complete all as specified.

Taking down old fitting and S&F Recces mounting (2'X2') 36w LED light fitting, integrated polycarbonate LED channel with white acrylic cover complete suitable for fixed properly on ceiling and connecting complete to fitting by three core copper conductor cable of overall sheathed size 2.5 Sqmm which shall be passed through PVC flexible conduit complete all as specified.

Taking down old fitting and S&F building security light LED fitting 35 watt 230V AC outdoor type with high pressure die cast aluminum housing and heat resistant , epoxy powder coated dark graphite grey colour finish and prismatic polycarbonate cover with individual LED lences suitable for including lamp LED 35 watt, fixed / connect properly at directed location on building with IP 65/66 protection complete all as specified.

Taking down old unservisable celling fan and depositing in to MES Store yard of AGE E/M fan and S&F Ceiling fan 1200mm sweep single phase 230 volts AC, min air delivery 210 CFM with service valve 6.00 BEE 5 star rating with brushless direct current motor (BLDC) with blade ,down roads electronic regulator and complete accessories complete fixed properly on wall surface with the provisioning of suitable sizes of rag bolts, nuts, washer and to connect by using cable PVC insulated copper stranded conductor of size 2.5 Sqmm 3 core and overall PVC sheathed which shall be passed through PVC flexible conduit of length not exceeding 0.50 mtr complete all as specified.

Taking down old unservisable exhaust fan and depositing in to MES Store yard of AGE E/M and S&F for PVC body Exhaust Fan 450 mm sweep, single phase 230 volts AC, 900 RPM four blade with louver shutters complete fixed properly on wall surface with the provisioning of suitable sizes of rag bolts, nuts, washer and to connect by using cable PVC insulated copper stranded conductor of size 2.5 Sqmm 3 core and overall PVC sheathed which shall be passed through PVC flexible conduit of length not exceeding 0.50 mtr complete all as specified.

M & L in repair for building earthing complete with galvanised steel earth plate electrode 60 x 60x 6mm burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edged of the plate not less than 1.5 mtr below normal ground level, connected to galavanised iron earth lead by means of bolt, nut, check nut and washer of galavanised iron wire 4mm as earthing lead as shown in Electrical Plate No 3 of SSR Part I connected to earthing test point all as specified or indicated including testing on completion including necessary excavation and earth work in hard/dence soil, earth pit in PCC 1:3:6 type C1 using 20mm stone aggreate, funnel, 20mm dia GI medium grade water pipe, 15mm dia GI light grade earth lead protection pipe, CI frame and cover, wire, copper lugs, wire mesh, charcoal or coke and common salt in alterative layer all around the earth electrode compacted thickness 15 cm including excavation and earth work pit cover including disposal of surplus soil to a distance not excessding 50m, complete testing on completion all complete as shown in electrical plate No 3 of SSR Part I 2009 complete all as specified.

Narender Constrution Company (BID ID -3149691)