PROVISION OF ONE STORE ROOM AT HQ CWE (AF) BAREILLY AT AF STATION BAREILLY

B/R (P) Portion: Surface excavation not exc 30cm deep and averaging 15 cm deep and getting out in any type of soil.

Excavation in trenches not exc 1.50 mtr wide and 1.50 mtr in depth for foundation etc or for shafts, wells, cespits, manholes, pierholes etc not exc 10 Sqm on plan and getting out in soft / loose soil all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer in soil all as specified.

Removing excavated material (soil) to a distance not exceeding 50 mtr and depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and directed

M&L for cement concrete type D-2, mix 1:4:8 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, sub base of floor etc complete all as specified and directed.

M&L for fly ash brick work with old size bricks having crushing strength not less 75 kg/ Sqcm, straight or curved on plan and built in cement mortar 1:6 complete all as specified.

M&L for 40 mm thick cement concrete 1:2:4 tppe B-0 (using 12.5 mm graded stone aggregate) mixed with water proofing compound as per manufacturer's instruction as in damp proof course to horizontal or vertical surface including necessary form work complete all as specified.

M&L for hard core of gauge not exceeding 63 mm, deposited, spread and leveled in layers not exceeding 15 cm thick, watered and rammed to a true surface using broken stone or boulders complete all as specified.

M&L for 100 mm thick cement concrete 1:4:8, type D-2 using 40mm graded stone aggregate as in sub base of floor and pavings complete all as specified.

M&L for 50 mm thick cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in floors including finishing surface even and smooth without using extra cement complete all as specified.

M&L for 38 mm wide glass dividing strip, 3mm thick inserted in position conform to design etc complete

M&L for reinforced cement concrete 1:1.5:3 type A-1 (using 20mm graded stone aggregates) as in beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified

M&L for mild steel TMT bar 10 mm dia and over, cut to length , bent to shape required, including cranking, bending spirally for hooping for coloums, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc complete.

All as per item No 13 above but for 8 mm dia as in sitrrups, spacer etc complete all as specified.

M&L for formwork to edges of concrete flats, treads, breaks in floors window cills, concrete railings, openings in concrete walls, floor and roofs not exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and siilar work exc 10cm but not exceeding 20cm wide etc complete

M&L for formwork to sides and soffits of floor or roof beams, beams, beams haunchings, griders, bressumers, lintels, cantilevers, shelves including suppots overhangs etc also splays between floors and beams etc complete alll as specified.

S&F for mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290, Gde E-165 complete all as specified.

S&F for steel window with side hung shutters including box type hinges (02 Nos), mild steel tower bolt 100 mm size over MS flat iron for each openable leaf & Z section handle and steel peg stay complete with glazing bars dovetailed or welded conforming to IS-1038 complete all as specified and directed

All as per Item No. 18.00 above but without glazing bars dovetailed or welded. (Note for Item No. 18.00 & 19.00:- Glass and wire cloth shall be measured and paid separately)

S&F for stainless steel wire cloth, 0.56 mm nominal dia of wire and average with of aperture 1.18 mm and fixed with stainless steel wire staples complete all as specified.

M&L for 3 mm thick sheet glass ordinary quality and glazing and oil putty in squares not exc 0.5 Sqm in each pane complete all as specified.

S&F for rolled mild steel joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) conforming to Fe-410-W (Gde-E- 250) quality-A complete all as specified.

M&L for 15 mm thick rendering in cement mortar 1:4 on fair faces of brick or concrete surfaces of wall including finished fair & even surface without using extra cement with WPC complete all as specifed. (Note: WPC shall be measured and paid separately)

M&L for rendering 15mm thick in cement mortar 1:6 on other than fair faces of brick or concrete surfaces of wall including finished even & smooth surface without using extra cement all as specifed.

Supply only integral water proofing compound.

M&L for preparation of newly plastered surface of walls and applying three coats of white wash complete all as specified.

M&L for preparation of newly plastered surface of walls and applying two coats of cement based paint complete all as specified.

M&L for preparation of newly or previously untreated steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specifed.

M&L 75 mm thick cement concrete type C-1, 1:3:6 (using 20 mm graded stone aggregate) as in plinth protection, laid in bay not exc 3.00 sqm each including finished even and smooth without using extra cement with and including all necessary form work to divide the area in panels, finishing exposed edges fair or rounding or chamfering where directed and providing 6 mm wide joints through out the thickness of plinth protection duly filled with bitumen mastic filling (one part of hot bitumen 85/25 and three part of fine sand by weight) complete all as specified and directed.

S&F for pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws complete all as specified.

M&L for galvanished iron frame for seamless ceiling with two unequal flanges of 20 mm and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/interediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with GI cleat and steel expansion fasterners with and including ceiling section ( not exceeding 1.2 mtr length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26mm each with lips of 10.5 mm fixed to the intermediate chanel with connecting clips across the intermediate channel at 457mm centre to centre including hanger 6mm dia GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 mm x3 mm size 60 mm long and expansion hold fasterners 12.5 mm dia 40 mm long complete all as specified

M&L for 6 mm thick non asbestos fibre cement building boards fixed or laid / inserted to timber / GI / Aluminium framework with screws etc complete all as specified.

E/M PORTION : M&L for point wiring using approved colour coding as per IS with multistranded copper conductor 1.5 Sqmm (nominal area) with two single core PVC insulated and unsheathed FRLSH cable 1100 Volts grade ISI marked drawn through and including heavy duty PVC concealed conduit including all accessories after chasing, cutting etc in wall / ceiling etc and heavy duty ISI marked GI sunken boxes 1.2 mm thick, 60 mm deep with earth dolly duly, covered with modular white cover plate with frame suitable for modular switches, including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly for one light point controlled by one way switch all as specified. [Note:- M&L for cutting chases for concealed conduit wiring on any surfaces and making good disturbed surfaces to match with the existing surfaces in cement mortar 1:3 and finishing with existing finishes shall be deemed to be included in the quoted rate.]

All as per item No. 33.00 above but for one 3 pin socket outlet, 5/6 Amps on independent board.

All as per item No. 33.00 above but for socket outlet 5 Amp on same board.

All as per Item No. 33.00 above but for multistranded copper conductor 2.5 Sqmm (nominal area) with two single core PVC insulated and unsheathed FRLSH cable 1100 volts grade ISI marked drawn through in and including heavy duty PVC concealed conduit including all accessories after chasing in wall/ceiling etc including PVC insulated multistranded copper conductor 2.5 Sqmm (nominal area) single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly all as specified and directed.

S&F for wall / surface mounted type LED light fitting batten type complete with LED 1x20 Watt (4 feet long), extruded aluminium body with heat sink provided for efficient heat dissipation and integrate electronic drive complete with all accessories internally pre-wired and including connecting up with 3 core twisted flexible copper conductor cable complete all as specified.

S&F for modular switch one way 6 Amp , one module ISI marked complete all as specified.

S&F for modular socket outlet 2 in 1, 3 pin, 5/6 Amp 2module ISI marked flush type complete all as specified.

S&F for modular switch outlet 2 in 1, 3 pin,15/16 Amp one module ISI marked complete all as specified.

S&F for modular socket outlet 2 in 1, 3 pin, 15/16 Amp 02module ISI marked flush type complete all as specified.

S&F for ceiling rose 65 mm x 50 mm three terminals complete all as specified and directed.

S&F for flush mounting factory made Ekinoxe SPN DB's Double door, IP-43 Protection, IK-09 with metal door, with neutral bar, Earth bar and cables ties for cable management fully insulated bus bar 4 way with 100 Amps rated bus bar complete all as specified and directed.

S&F for MCB SPN 32 Amps (single pole and neutral) 240 volts, breaking capacity 10 KA, ‘C’ Series complete all as specified.

S&F for MCB SP 6 to 32 Amps (single pole) 240 volts, 50HZ, 10 KA, ‘C’ series complete all as specified.