Annual RandM works Bhagwanpur

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in charge.: All kinds of soil

Surface dressing of the ground including removing vegetation and in?equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. All kinds of soil

Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared.

Supplying chemical emulsion in sealed containers including delivery as specified.Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : long the external wall below concrete or masonry apron us ing chemical emulsion @ 2.25 litres per linear metre includ ing drilling and plugging holes etc. With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -All work up to plinth level: 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mmnominal size derived from natural sources)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal sizederived from natural sources) .

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. ( mild steel) and medium tensile steel.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished) machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edge to give high gloss finish etc. complete at all levels.Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble.Area of slab upto 0.50 sqm.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia& Paisalength ( hold fast lugs or dash fastener shall be paid for separately).: (Sal wood)

Providing and fixing fly proof galvanised M.S. wire gauge to windows and clerestory windows using galvanized M.S. wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.63 mm all complete With .DSR 2nd class teak wood beading 62X19 mm.

Providing and fixing ISI marked oxidised M.S. pressed butt hinges with necessary screws etc. complete: (100x58x1.90mm)

Providing and fixing ISI marked oxidised M.S. pressed butt hinges with necessary screws etc. complete: (75 x 47x1.70mm)

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete: (300x16mm)

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete: (250x16mm)

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete. (250x10mm)

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete. (150x10mm)

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete : 125 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Single rubber stopper

Strutural steel work riveted bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete:

Cement concrete flooring 1:2:4 (1 cement : 2coarse sand : 4 gradd stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete. (40 mm thick with 20mm nominal size stone aggregate).

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm dia

12mm cement plaster of mix: 1:6 (1cement : 6coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1 cement: 6 coarse sand)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface. Water thinnable Cement primer.

Lettering with black Japan paint of approved brand and manufacture

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Painting with acid proof paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work

Providing and fixing C.P. brass chain and rubber plug complete for sink or wash basin: 40 mm dia.

Distempering with 1st quality acrylic distemper (ready mixed ) having VOC content less than 50 gms/litre of approved manufacturer of required shade and colour complete, as per manufacturer's specification. Two or more coats on new work .

White washing with lime to give an even shade : Old work (two or more coats)

Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 metres lead : With cement mortar 1:4 (1cemnt :4 Coarse snad)

Renewing glass panes, with putty and nails wherever necessary including racking out the old putty:Float glass panes of thickness 4mm

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: One or more coats on old work.

Finishing walls with water profing cement paint of required shade: Old work (one or more coats aplied @ 2.20kg/10sqm).

Finishing walls with Acrylic Smooth exterior paint of required shade :Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface).

Demolishing cement concrete manually/by machanical means including disposal of material within 50 metres lead as per direction of Engineer-in-charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

Demolishing cement concrete manually/by machanical means including disposal of material within 50 metres lead as per direction of Engineer-in-charge. Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix)

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable materialwithin 50 metres lead as per direction of Engineer-in-charge.In cement mortar.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fitttings complete. Flexible pipe 32mm.dia

Providing and fixing G.I. pipes complete with G.I. fittings and clamps including cutting and making good the walls etc. Internal work -Exposed on wall. 15mm dia. nominal bore)

Providing and fixing G.I. pipes complete with G.I. fittings includingtrenching and refilling etc.15 mm dia nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings includingtrenching and refilling etc.20mm dia nominal bore

Providing and fixing brass bib cock of approved quality: 15mm nominal bore

Providing and fixing brass stop cock of approved quality: 15mm nominal bore

Providing and fixing Unplasticised PVC connection Pipe with brass unions. 45 cm length :15 mm nominal bore

Providing and fixing G.I. Union in G.I. Pipe , including cutting and threading the pipe and making long screws etc. : 15mm nominal bore.

Providing and fixing C.P. brass bib cock of approved quality conforming to.15mm nominal bore.

Providing and fixing in position wall panelling at all heights with integral densified calcium silicate panels/tiles of size 595 x 595mm, having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity <0.043 W/m K as per ASTM 518:1991, comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm including both sides) i.e.vertical studs of size 48 x 34 x 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50 x 32m fixed to the floor and soffit at 600mm centers using 12mm dia,50mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally calcium silicate non combustible panels/tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1 mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fiber joint tape roll 50mm wide (90 metre )roll and two coats of primer suitable for panelling as per manufacturer's specification as per direction of Engineer-in-Charge all completeWith 15 mm thick fully perforated square/butt edge light weight calcium silicate panels/ tiles

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with piano type switch, phenolic laminated sheet, suitable size M.S. box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. Group B.

Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group B.

Power plug wiring in PVC conduit (2x4 sq.mm.) ,wiring for light/power plug with 2x4 sqmm.FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, alongwith 1no.4 sqmm. FR PVC insulated copper conductor single core cable for loop earthing as required

Wring for circuit/submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required 2 X 4 sq. mm + 1 X 4 sq. mm earth wire.

Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required. 5/6 amps switch.

Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required. 15/16 amps switch.

Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required. 3 pin 5/6 amp socket outlet

Supplying and fixing following piano type switch/ socket on the existing switch box/ cover including connections etc. as required. 6 pin 15/16 amp socket outlet .

Supplying and fixing following modular switch / socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 5/6 amps switch.

Supplying and fixing following modular switch / socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 15/16 amp switch.

Supplying and fixing following modular switch / socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 amp socket outlet.

Supplying and fixing following modular switch / socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 6 pin 15/16 amp socket outlet.

Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing 3 pin, 5 amp ceiling rose on the existing junction box/ wooden block including connection etc. as required.

Supplying and fixing brass batten/ angle holder including connection etc. as required

Supplying and fixing call bell/buzzer suitable for single phase, 230 volts, complete as required.

Providing and fixing Havells plano RCE or equivalent LED panel light (Size 595x595 mm)complete in all respect. Based on market rate

Providing Carpenter Service for 8 hours service in a day or part as per requirement by experienced Carpenter with necessary T& PaisaP for attending minor type of repairing work as directed by the Engineer-In-Charge

Providing Wireman service for 8 hour’s service in a day or part as per requirement by experienced electrician with necessary Kit (holding license and T& PaisaP) for attending all type of electrical defects as directed by the Engineer-in-Charge.

Providing beldar service for 8 hours service in a day or part as per requirement to carry out the works as directed by the Engineer-In-Charge.

Providing fitter for Plumber service for 8 hours service in a day or part as per requirement by experienced Plumber with necessary Kit for attending minor type of all water supply defects as directed by the Engineer-in-Charge.

Sweeping of colony roads and srrounding area of residences and disposal of debris/garbage up to the nearest dustbin as per time schedule approved by E/I including cost of all labour and T&P etc. required for proper completion of work (approximate sweeping)

Cleaning of drains upto 0.3m wide and disposal of debris/ garbage up to nearest dustbin including sprinkling of lime powder near drains as per schedule approved by E/I including all labour, material and T&P etc. required for proper completion of work.

Cleaning of Nala more than 0.30 in wide and disposal of debris/garbege up to nearest dustbin including sprinkling of lime powder near nala as per schedule approved by E/I including all labour, material T&P etc. Required for proper completion of work.

Cleaning of Over Head tank capacity up to 1000 Ltrs. With brush, scraping of wall and bottom & disposal of rubbish outside the tank including all labour & T&P etc. Required for proper completion of the work.

Cleaning of Over Head tank capacity from 1001 to 30000 Ltrs. With brush, scraping of wall and bottom & disposal of rubbish outside the tank including all labour & T&P etc. Required for proper completion of the work.

Disposal of garbage/ debris from dustbin of places as directed b E/I outside the substation area including sprinkling of white lime powder in dustbins and surrounding area including cartage, labour, material and T&P etc. required for proper completion of work.

Manual Chlorination of water by adding bleaching power as per direction by Engineer in charge including all labour T&P etc. required of proper completion work.

Providing water proofing treatment on roof and wall by Dr. Fixit Pidicrete URP compound of pidilite make cleaning of surface with wire brush. Mixing of pidicrete URP compound (1 part of compound, 1.50 part of cement as permanufacture instruction) and apply its two coats on leaky surface @ average 0.50 kg/sqm for two coats by skilled labour as per instruction of manufacturer and applying top coat of 12 mm cement plaster 1:4 cement and coarse sand mortar including cost of all material labour T&P etc required proper completion of the work.

Taking off the defective ceiling fan from position and rechanging after receiving the repaired fan and proper connection etc.

Supply and replacing of wooden board 8"x10" approved quality including all material, labour, T&P & Polishingetc. Required for proper completion of work.

Supply and replacing of wooden board 4"x7" approved quality including all material, labour, T&P & Polishingetc. Required for proper completion of work.

Supply and replacing of 15 mm dia tee/socket/ elbow/ bend /nipple etc for repair of pipeline complete. including supply of all material, labour and T& P etc. required for proper completion of the work.

Easing door and Windows including supply of all labour T& P etc. required for proper completion of the work.

Hiring charges of welding machine for 8 hours. Per day. With all labour, T&P and including welded rod as required for proper completion of work

Providing & Fixing C.P Brass Pillar Cock of approved quality 15 mm nominal bore (weight not less then 400 grms).

Extraction of defective submersible pump and motor upto 5HP with 32mm PVC/ GI pipe and then lowering of the repaired pump and motor with pipe and testing the same , including checking mains cut outs fuses and operation of tubewell for 24 hrs for its smooth working with all cost of materials, labour T&P etc. required for the proper completion of the work.

Winding of submersible pump of motor upto 5HP vertical type or horizontaal type, including cleaning , oiling greasing drying etc with cost of all material, labour , T&P etc. complete burnt copper wire shall not be taken back from the contractor , approved make copper wire shall be used

Disassembling of up to 5 HP submersible pump Replacing of damaged bush impeller nut &bolts turning of shaft including complete overhauling oiling and greasing the pump as required testing and reassembling the same including cost of all materials labour T&P etc required for proper competion of work.

Supply and fixing star-delta starter with single phase preventer suitable for 10 HP submersible motor – pump of SIEMENS make model no.-3TE0290-OA.7A Ranging from 12.5-20.00 Amp including all labour material cartage etc. required for proper completion of the work

Supplying & Fixing flat submersible cable of superior quality as directed by engineer-in-charge. (3x4.0) sq.mm approved make including all material and T&P etc. Complete.

sushilprasad