Construction of building of Integrated Command Control Centre for DSCL Dharamshala Distt Kangra HP

Amount

Cutting in earth work through mechanical means in all heights / depths and in all kinds of soil such as kankar, moorum, shingle and decomposed or soft rock, hard rock i.e. their intermediate classification and chiselling / wedging out of rock where blasting prohibited including saturated soils and filling in embankments etc.where necessary and disposal of all excavated unserviceable material in all leads and lifts including through mechanical transporation, the disposal of the unserviceable material will be done on approved dumping site. Any damage to the private / public property during execution will be restored by the contractor whatsoever the nature of the same may be. The serviceable materials will be stacked in specified dimensions in all leads and lifts as per the direction of the Engineer -in- charge.

Excavation in foundations, trenches etc. in earth work in all kinds of soils such as pick work, jumper work, blasting work and chiselling / wedging out of hard or soft rock where blasing is prohibited up to all depths stacking the excavated soil not more than 3 meteres clear from the edge of excavation and then returning the stacked soil in 15 cms layers, when required into plinths, sides of foundations etc. consolidating each deposited layer by ramming and watering and then disposing off all surplus excavated earth as directed by the Engineer-in- charge.

Excavation in earth work and filling in 15 cm. layers in foundation and plinths including ramming, watering and consolidating including carriage of material in all leads & lifts.

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete including cost of sand including carriage of material in all leads and lifts.

Providing form work with steel plates 3.15mm thick welded with angle iron frames 30x30x5mm so as to give a fair finish including centering, shuttering, strutting and propping, etc. with wooden battens and ballies heights of propping and centering below supporting floor to ceiling in all heights and removal of the same for in-situ reinforced concrete and plain concrete work including carriage of material in all leads and lifts.

Foundation, footing bases of columns etc. and mass concrete.

Beams, cantilevers, girders and lintels sides and soffits of beams, small ends of beams,beam haunching, cantilivers, girders, bressumers and lintels not exceeding 1 metre in depth.

Flat surfaces such as soffits of suspended floors, roofs inluding inclined surfaces up to any degree, landings and the like:(i) Floors, etc. upto 200 mm in thickness.

Column, pillars, posts and struts upto all heights.(i) Square,rectangular or polygonal in plan.

Circular or curved in plan.

Stair cases with sloping or stepped soffits excluding landing.

Vertical surfaces such as walls (any thickness) partitions and the like including attached pillasters buttresses,plinth and string courses and the like.

Edges of slabs and breaks in floors and walls Under 20 cm. wide.

Providing and laying cement concrete 1 : 4 : 8 (1 cement : 4 sand : 8 graded stone aggregate 40 mm nominal size) and curing complete (excluding cost of form work) in foundation and plinth including carriage of material in all leads & lifts.

Providing and laying cement concrete 1 : 6 : 12 (1 cement : 6 sand :12 graded stone aggregate 40 mm nominal size) and curing complete excluding cost of form work in foundation and plinth including carriage of material in all leads & lifts.

Providing and laying cement concrete 1 : 8 : 16 (1 cement : 8 sand : 16 graded stone aggregate 20 mm nominal size) and curing complete on slab and floor excluding cost of form work screed laid under flooring including carriage of material in all leads & lifts.

Providing and Laying cement concrete 1:5:10 with 15% plums and curing complete including the cost of farmwork for plain/reinforced concrete in retaining walls, breast walls,the size of plum should be 150 to 300 mm as per drawing and HP.PWD technical specifications. including carriage of material in all leads & lifts.

Providing and laying cement concrete 1:2:4 (1 cement:2 Sand:4 graded stone aggregate 20mm nominal size) and curing complete excluding cost of form work in foundation and plinth including carriage of material in all leads and lifts.

Providing and laying cement concrete having strength of M-25 mixed design aggregate mechanically mixed and vibrated and curring complete excluding cost of form work and reinforcement for reinforced concrete works including carriage of material in all leads & lifts.

Foundations, footings, bases of column and the like and mass concrete.

Suspended floor, roofs, landings, shelves and their support, balconies, beams, girders, bressumers and cantilevers in all heights.

Column, pillars, posts and struts upto floor two level.

Walls (any thickness but not less than 0.10metre thickness) including attached pilasters buttresses , plinth and string courses etc. from top of foundation upto all floor level.

Stair cases (except spiral stair cases) excluding landing but including preparing of the surface and finishing of nosing upto floor two level.

Providing Tor steel /TMT Steel reinforcement for R.C.C. work including bending, binding and placing in position complete including cost of binding wire upto all heights including carriage of material in all leads and lifts.

Applying cement slurry on RCC slab or cement concrete work using 2.75 kg. of cement per sqm.of floor area before laying cement concrete flooring including roughening, cleaning, of the concrete surface complete including carriage of material in all leads & lifts.

Brick work using 2nd class common burnt clay building bricks in foundation and plinth in cement mortar 1:3 (1 cement : 3sand) including carriage of material in all leads and lifts.

Half brick masonry using 2nd class common burnt clay building bricks in super-structure above plinth level upto all floor level in cement mortar 1:4 (1 cement : 4 sand) including carriage of material in all leads & lifts.

Random rubble masonry/polygonal rubble masonry (uncoursed/ brought to courses) with hard stone of approved quality in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 sand : 12 graded stone aggregate 20 mm nominal size) at plinth level in cement mortar 1:6.(1 cement: 6 sand) including carriage of material in all leads & lifts.

Stone soling properly hand-packed filling interstices with spalls and consolidating with power road roller to the requested gradient and camber including spreading watering and rolling of binding materials moorum or earth etc. complete as per HP.PWD specification. 100 mm spread thickness (finished work including materials and labour) including carriage of material in all leads & lifts

Stone filling behind retaining walls including carriage of material in all leads & lifts.

Providing and laying autoclaved aerated cement blocks masonry with 150mm/250mm /300mm thick AAC blocks in superstructure above plinth level upto all floor level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge including carriage of material in all leads & lifts.(The payment of RCC band and reinforcement shall be made for seperately)

Providing and fixing single/double leaf 12 mm thick frame less toughened glass for door shutter / partition with tempered forested glass for swing door of approved brand and manufacture, including providing and fixing top & bottom pivot and spring type fixing arrangement and making necessary holes etc. for fixing required fittings, all complete as per direction of Engineer-in- charge including carriage of material in all leads & lifts.

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically -sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No. 25.2). For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with refletive soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear glass of approved make having properties as visible light transmittance (VLT) of 25 to 35 % , Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25-0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement including carriage of material in all leads & lifts.

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 asper BS 1474, including super durable powder coating of 60-80 micronscon forming to AAMA 2604 of required colour and shade as approvedby the Engineer-in-Charge. ( The item includes cost of material suchas cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account) including carriage of material in all leads & lifts.The weight of aluminium extruded section shall be taken forpurpose of payment

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable including carriage of material in all leads and lifts. Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Providing and fixing fire resistant door frame of section 50x60 mm horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet (Zinc coating not less than 120gm/m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter.The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in- charge . (Cost of SS ball bearing hinges is excluded) including carriage of material in all leads and lifts.

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete including carriage of material in all leads and lifts.

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame,consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge including carriage of material in all leads and lifts.(panelling to be paid for seperately).

Providing and fixing stainless steel sliding door bolt as per colour and shade approved by the Engineer-in-Charge with bolts and nuts screws etc. complete including carriage of material in all leads & lifts. 250x16mm

Providing and fixing stainless steel tower bolt (barrel type) as per colour and shade approved by the Engineer-in-Charge with screws etc. complete including carriage of material in all leads & lifts.

Providing and fixing stainless steel handles as per colour and shade approved by the Engineer-in-Charge with necessary screws including carriage of material in all leads & lifts.

Providing and fixing 100mm stainless steel floor door stopper with rubber cushion screws etc. to suit shutter thickness complete including carriage of material in all leads and lifts.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge With stainless steel cover plate minimum 1.25 mm thickness including carriage of material in all leads and lifts.

Providing and fixing of High Pressure Laminate Sheet for external cladding as per technical specification and drawings complete in all respect (Rates are inclusive of all material, labour, fixtures & fittings, tools and tackles required for completing the work) including carriage of material in all leads and lifts.

Wooden flooring (Solid) tiles of premium Grade-"A" quality with minimum colour variation 15 x 150 mm width High Grade finish of matt lacqured gloss,resistent to stains, scraches and hard- wearing with all necessary frames and finished in all respect including carriage of material in all leads and lifts.

Providing and fixing 10mm thick anti skid water proof stain and impect resistent heavy duty vetrified tiles any size / colour / shade / design approved by Engineer-in-charge in flooring, / skirting, treads and riser of steps and landings laid over 12mm thick cement mortar 1:3 (1 cement : 3 sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete including carriage of material in all leads and lifts.

Providing & fixing pre-polished vetrified ties of any size and any colour as per where required in skirting, risers of steps and dado on 12mm thick cement mortar 1:3 (1cement:3 sand) & jointed with cement slurry including carriage of material in all leads and lifts.

Stone solling properly hand packed under floors etc complete as per HPPWD Specification including carriage of material in all leads and lifts.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm , at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I.wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :-12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks) including carriage of material in all leads & lifts.

Providing and laying flamed finish Granite stone flamed and brushed finishes/sand blasted finishes of any shade (Any colour and any size) flooring / skirting and riser of steps in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 16 to 18 mm thick stone slab (heavy Duty) over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge including carriage of material in all leads & lifts.

Providing and laying 20mm. thick granite stone in flooring 20mm(average) thickness base of cement mortar 1:3(1cement : 3 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone including rubbing and polishing complete including carriage of material in all leads & lifts.

Providing and laying heavy duty precast cement conrete 60mm thick inter locking paver blocks vibro compacted upto M-35 grade including border or kurb block grey or coloured over sub-base of concrete with 25mm thick average thickness of cement mortar 1:4 (1 cement : 4sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks including curing rubbing & polishing complete (Sub base concrete floor to be paid for seprately) including carriage of material in all leads & lifts.

Providing and laying heavy duty precast cement conrete 50mm thick inter locking paver blocks vibro compacted upto M-30 grade including border or kurb block grey or coloured over sub-base of concrete with 25mm thick average thickness of cement mortar 1:4 (1 cement : 4sand) laid over and jointed with neat cement slurry mixed with pigment to match the shade of blocks including curing rubbing & polishing complete (Sub base concrete floor to be paid for seprately) including carriage of material in all leads & lifts.

Providing and laying marble work (Table rubbed and polished) in flooring 20mm. thick base in cement mortar 1:3(1cement:3sand) including jointing with cement mortar 1:2 (1 white cement:2 marble dust) with an admixure of pigment to match the shade of the marble 20 mm thick White makrana marble including carriage of material in all leads & lifts.

Providing and laying 40 mm thick cement concrete flooring 1:2:4 ( 1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size) laid in one layer finished with a floating coat of neat cement including carriage of material in all leads and lifts.

Providing and laying 50 mm thick cement concrete flooring 1:2:4 ( 1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size) laid in one layer finished with a floating coat of neat cement including carriage of material in all leads and lifts.

Providing water proofing and filling for Toilet / Balcony / Utility in two parts as per the specifications listed below and as approved by the engineer-in-charge with a guarantee of 10 years : The first part consisting of providing and applying Acrylic Polymer Modified Flexible Cementitious Coating [approved systems : as per the list of approved makes in 2 or 3 coats as per manufacturers’ specification and as approved by the engineer-in-charge to the sunk slab and walls up to minimum 1 M height, complete. The treatment to include cleaning and wire-brushing the concrete surface, treating all the cracks (wider than hairline), construction joints and honeycombs by grouting with specialised non-shrink cementitious compound, grouting the annular space between the pipe and concrete / masonry, providing and applying a protective 15 mm thick, CM 1 : 4 plaster admixed with integral waterproofing compound, curing, at all levels and heights, etc., complete

Providing and laying APP (Atactic Polypropylene Polymer) modified prefabricated five layer 3 mm thick water proofing membrane, black finished reinforced with non-woven polyester matt consisting of a coat of bitumen primer for bitumen membrane @ 0.40 litre/sqm by the same membrane manufacture of density at 25°C, 0.87-0.89 kg/ litre and viscocity 70-160 cps. Over the primer coat the layer of membrane shall be laid using Butane Torch and sealing all joints etc, and preparing the surface complete. The vital physical and chemical parameters of the membrane shall be as under : Joint strength in longitudinal and transverse direction at 23°C as 650/ 450N/5cm. Tear strength in longitudinal and transverse direction as 300/250N. Softening point of membrane not less than 150°C. Cold flexibility shall be upto -2°C when tested in accordance with ASTM, D - 5147. The laying of membrane shall be got done through the authorised applicator of the manufacturer of membrane :3mm thick.

Providing and fixing 0.60 mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP ) organic coating of 20 microns over 5 microns primer coating + back of polyster of 5 microns over, 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6 mm dia meter with prepainted limpet & rubber washers complete with all accessories as required as per the direction of Engineer - in - charge including carriage of material in all leads and lifts.

Providing & fixing ridges or hips 60cm overall with 0.60 mm thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP ) organic coating of 20 microns over 5 microns primer coating (+) back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6 mm diameter with prepainted G.I. limpet & bitumen washers complete with all accessories as required as per the direction of Engineer - in - charge including carriage of material in all leads and lifts.

Providing and fixing valley 60 cm overall 0.60mm thick prepainted steel sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia with prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-in-charge including carriage of material in all leads & lifts.

Providing & fixing 15 cms wide 45 Cms. overall semicircular plain G.I. Sheet gutter with iron brackets 40x3mm size bolts and nuts and washer etc. including making necessary connections with rain water pipes complete as per design including carriage of material in all leads & lifts. (a) 0.63mm thick sheet.

Providing and fixing M.S. BP Sheet 1.66mm to 2mm thick in eaves board/facia/soffits/ ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely) including carriage of material in all leads and lifts.

Providing and fixing on wall face PVC (D-Plast) rain water pipes of working pressure not less than 4.5 kg/sqm including filling the joints with approved adhesive complete including carriage of material in all leads and lifts.(a)100mm dia pipes

Providing and fixing on wall faces PVC (D-Plast) accessories for rain water pipes including filling the joints with approved adhesive complete including carriage of material in all leads and lifts

PVC Plain Bend 100 mm diameter

PVC.plain shoe 100mm diameter.

Steel work welded in built up sections, trusses and framed work, including cutting,hoisting, fixing in position and applying a priming coat of red lead paint including carriage of material in all leads and lifts.

(a)In beams joists channels ,angles ,In tee ,flats with connecting plates or angle cleats as in main and cross beams,hip and jack rafters,purlins connected to common rafters and the like.

(b)In gratings framed guard bars,ladders,railling,brackets and similar works.

Providing and fixing stainless steel railing mark-36 pipe sizetop-2' pipe, post pipe 1" and 3' hight in staircase including necessary fittings and positions complete as per design approved by the Engineer-In-Charge including carriage of materials in all leads and lifts.

Providing and fixing Automatic sensor door with all material and necessary fittings for entrance door Entrance door including carriage of material in all leads and lifts.

Providing and applying two coats of fire retardant paint including preparation of base surface as per recommendations of manufacturer to make the surface fire retardant including carriage of material in all leads and lifts.

Wall painting two coats with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams / litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour including carriage of material in all leads and lifts.

Applying one coat of Acrylic primer (Spectrum or equivalent of Superior quality) on new concrete/masonry/plastred surfaces after and including preparing the surface by thoroughly brushing the surface free from mortar droppings and other foreign matters, sand papering the surface smooth complete including carriage of material in all leads and lifts.

Varnishing with varnish of approved brand and manufacture one or more coats with copal varnish including carriage of material in all leads and lifts.

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat, preparation of surface, etc. complete on concrete work including carriage of material in all leads and lifts.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar drops, dust, loose materials and other foreign matters sand papered smooth to give final matter finish to the surface complete including carriage of material in all leads and lifts.

15 mm cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering upto all heights including arises, Internal rounded angles, chamfers and / or rounded angles not exceeding 80 mm in girth and finished even and smooth in cement mortar 1:6 ( 1 cement : 6 sand) including carriage of material in all leads and lifts.

20 mm cement plaster in single coat on rough side of brick / stone masonry for interior plastering upto all heights including arises, internal rounded angles, chamfers and / or rounded angles not exceeding 80 mm in girths and finished even and smooth in cement mortar 1:4 (1 cement : 4 sand) including carriage of material in all leads and lifts.

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1 Cement : 3 Sand : 6 Graded stone aggregated 20mm nominal size) including carriage of material in all leads and lifts.

Providing under layer for plinth protection of 75mm thick (unconsolidated) bed dry brick / stone aggregated 40mm nominal size with rammed and consolidated and grouted with fine sand including preparation of ground including carriage of material in all leads and lifts.

Constructing Course rubble hammer dressed 'U' shape open surface drain with side wall 15x22 cm in cement mortar 1:6 (1 Cement : 6 Sand) and inside plastring with cement plaster 1:3 (1 Cement:3 Sand) including earth work and laying 10 cm cement concrete in 1:5:10 (1 Cement : 5 Sand : 10 graded stone aggregate) of 40 mm nominal size) and 7.5 cm cement concrete 1:2:4 (1Cement : 2 Sand : 4 Graded stone aggregate of 20 mm nominal size) and finished with a floating coat of neat cement complete as per standard design including carriage of material in all leads and lifts.

Providing weep holes in brick masonry / stone masonry /plain reinforced concrete abutment, wing wall, return wall with 100 mm dia PVC pipe extending through the full with of the structures with slop of 1(v):20(H) towards drawing face complete as per drawing and technical specification clauses 614, 709, 1204.3.7 including carriage of material in all leads and lifts.

Providing and fixing 12 mm thick prelaminated board both side bwp phenol bonded exterior / interior grade shutters withframe of 1st class deodar wood for cup board including nickel plated bright finished piano hinges 25mm thick frame including carriage of material in all leads and lifts.

Providing and fixing 19mm thick Commercial Board water proof shutters for up boards including fixing with nickel plated piano hinges with screws etc complete including carriage of material in all leads and lifts.

Providing and fixing bright finished brass 100mm. Mortice latch and lock and a pair of levers, handles with necessary screws etc. complete (indian make of approved quality) including carriage of material in all leads and lifts.

Providing and fixing bright finished brass ball catcher 10 mm dia including carriage of material in all leads and lifts.

Providing and fixing bright finished 100mm brass handles with screws etc. complete including carriage of material in all leads and lifts.

Providing and laying 8mm thick stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete including carriage of material in all leads and lifts.(i) Granite of any colour and shade

Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991,in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main- T runners of size 24x38 mm of length 3000 mm, cross - T of size 24x32 mm of length 1200 mm and secondary intermediate cross-T of size 24x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x 25x 25 x 2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.With 15 mm thick tegular edged light weight calcium silicate false ceiling tiles.

Making connection of galvanised steel distribution branch with galvanised mild steel main 20mm to 40 mm nominal bore by providing and fixing tee including cutting and threading the pipes complete including carriage of material in all leads and lifts.

Constructing brick masonry chamber for under ground C.I. Inspection chamber and bends with common burnt clay building bricks in cement mortar 1:5 (1 cement : 5 sand ) C.I. Cover with frame (light duty ) 355mm x 610mm internal dimensions total weight of cover with frame to be not less than 38kg (weight of cover 23 kg. and weight of frame 15kg) R..C.C top slab with 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size ) foundation concrete 1:5:10 ( 1cement : 5 sand : 10 graded stone aggregate 40mm nominal size) inside plaster 15mm thick with cement mortar 1:3 (1 cement : 3 sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete including carriage of material in all leads and lifts.Inside dimensions 455 mm x 610 mm x 450 mm deep single pipe line.

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/6 litre (adjustable to 4 litre/8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Providing & Fixing white glazed vitreous china wash basin with, 32mm C.P. brass waste of standard pattern complete including cutting and making good the wall and sealing the sleeves as required including fixing on brackets including carriage of material in all leads and lifts. Under Counter wash basin

Providing and fixing one hole wash basin mixing Faucet including carriage of material in all leads and lifts.

Providing and fixing white vitreous china flat back half stall urinal of size 580x 380x 350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS:2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required including carriage of material in all leads and lifts. Range of two half stall urinals with 5 litre P.V.C. automatic flushing cistern

Providing and fixing Division Plate for Urinals 600mm x 300. Vitreous China including carriage of material in all leads and lifts

Providing and fixing stainless steel kitchen sink of approved standard ISI make with drain board and C.P. waste with C.I. or M.S. Brackets painted white including cutting holes and making good the same but excluding fitting including carriage of material in all leads and lifts.i) 610 x 510 mm with bowl depth 200 mm.

Providing and fixing Mixer for kitchen sink with casted swinging spout at top including carriage of material in all leads and lifts.

Providing and fixing C.P. brass angle valve 15mm without Nuts and pipe including carriage of material in all leads and lifts.

Providing and fixing PTMT Jet spray of approved quality & colour with 1.50 metre tube including screws etc. complete in all respect 15mm dia incliding carriage of material in all leads & lifts.

Providing and fixing towel rail complete with C.P. Brass brackets fixed to wooden plugs with C.P. brass screws including carriage of material in all leads and lifts.600mmx20 mm

Providing and fixing liquid soap container with C.P. Brass lid and brackets fixed to wooden plugs with C.P. Brass screws including carriage of material in all leads and lifts. Glass container

Providing and fixing C.P. Brass toilet paper holder including carriage of material in all leads and lifts.

Providing and fixing 32 mm dia C.P. Bottle Trap for wash basin and sink including carriage of material in all leads and lifts.

Providing and fixing 600mmx450mm bevelled edge mirror of superior glass mounted on 6mm thick A.C. sheet or plywood sheet and fixed to wooden plugs with C.P. brass screws and washers incliding carriage of material in all leads & lifts.

Providing and fixing Polyethelene-Aluminium-Polyethelene PE-ALPE Composite Pressure Pipes conforming to IS - 15450, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer-in-charge.

(a) 1620 (20 mm OD) pipe

(b) 2532 (32 mm OD) pipe

(c)3240 (40 mm OD) pipe

Providing and laying in trenches 32 mm dia galvanised mild steel tubes (medium grade), tube fittings (earth work in trenches to be measured and paid separately) incliding carriage of material in all leads & lifts.

Providing and fixing 15 mm nominal dia CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge including carriage of material in all leads and lifts.

Providing and fixing 25 mm dia gunmetal single acting air release valve with screwed inlet including carriage of material in all leads and lifts.

Providing and fixing stoneware gully trap grade 'A' complete with C.I grating, brick masonry chamber in cement mortar 1:5 and water tight C. I. cover with frame of 300mmx300mm size (inside) the weight of cover to be not less than 4.53kg and frame to be not less than 2.72kg including carriage of material in all leads and lifts.(i)Square Mouth Traps: 100mmx100mm size P type

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for Circular tank including carriage of material in all leads and lifts.(i) 1000 Ltrs.

Providing and fixing PVC Plain bend ISI marked including fixing with approved adhesive etc complete including carriage of material in all leads and lifts.

110 mm outer dia

150 mm outer dia

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.

110 mm outer dia

150 mm outer dia

Providing and fixing PVC single equal branch ISI marked including fixing with approved adhesive etc complete including carriage of material in all leads and lifts.

110 mm outer dia

150 mm outer dia

Providing and fixing sound insulated poly proplene piping system as per ON EN 1451-Part 1-6 & EN 12056 Part 1-5 with push-fit type, food safe, having high impact and stiffness, offering sound levels of not more than 21-23 dBA at a flow rate of 4 l/s and having pipe ring stiffness as per 1S0/DIS 9969 and tightness as per EN 1277/B and C and DIN 19560, with all necessary fittings in blue colour, fitted with factory fitted lip ring including carriage of material in all leads and lifts.

110 mm outer dia

160 mm outer dia

Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete (cost of water meter and stop cock to be paid separately). including carriage of material in all leads and lifts.

Providing and fixing plastic seat (solid /Hollow type) and cover for wash down water closet with C.P. brass hinges and rubber buffers including carriage of material inall leads & lifts.(a) White plastic seat and cover

Providing and fixing 32mm dia rubber plug for sink / wash basin including carriage of material inall leads & lifts.

Providing and fixing C.P. Brass waste for wash basin or sink including carriage of material inall leads & lifts.

Providing and fixing M.I. Union for wash basin or sink including carriage of material inall leads & lifts.

Providing and fixing chromium plated brass soap dish with C.P. Brass brackets fixed to wooden cleats with C.P. Brass screws including carriage of material inall leads & lifts.

Providing and fixing Tooth brush and Tumbler holder (Vitreous China) including carriage of material inall leads & lifts.

Providing and fixing 30 cms length 15mm nominal bore C.P. connection pipe with brass unions including carriage of material inall leads & lifts.

Providing and fixing 32mm nominal bore brass full way valve with wheel including carriage of material inall leads & lifts.

Providing and fixing 32mm nominal bore G.I. / M.I. union including carriage of material inall leads & lifts.

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete including carriage of material inall leads & lifts.

110 mm dia

150 mm dia

Constructing man hole with RCC top slab in 1:2:4 mix (1cement:2sand: 4graded stone aggregate 20mm nominal size ) Foundation concrete 1:4:8 (1cement : 4sand : 8 graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortor 1:3(1 cement:3 sand) finished with a floating coat of neat cement and including making channels in cement concrete 1:2:4 mix (1cement : 2 sand : 4 graded stone aggregate 20mm nominal size) finished smooth complete including curing and testng including carriage of materials in all leads and lifts. (a) Inside size 1200mm x 900mm x1000mm deep including S.F.R.C. frame and cover medium duty 500mm diametre internal size.With 200mm thick walls of brick masnoey using common burnt clay building bricks in cement mortor 1:3 (1 cement :3sand) .

Supplying and fixing S.F.R.C. cover with frame for manholes/Septic tank for frames of tank for frames of 500mm internal diameter (medium duty) the weight of cover to be not less than 80 Kg and weight of frame to be not less than 103 kg including carriage of material in all leads and lifts

Providing and fixing 100mm nominal diameter cast iron cowl ISI marked including fixing with approved adhesive etc. complete including carriage of material in all leads and lifts.

Proving and fixing C.P. brass bib tap (Superior or heavy type) (Confirming to BIS specifications) including carriage of material in all leads and lifts. 15 mm dia with Swinging spout top / bottom outlet

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive,cost of cutting and making good the wall and floors etc, complete including carriage of material in all leads and lifts.(a) 110 x 75mm

Om Parkash Sharma And Sons

NARESH KUMAR TULI