City Sanitation Action Plan- For used Water Management under SBM-U-2.0 Under Interception and Diversion in respect of Nagar Panchayat Rewalsar under the Jurisdiction of Jal Shakti Division Baggi in Tehsil Balh Distt. Mandi

Excavation in foundation and trenches etc. in earth work in all kind of soils such as pick work jumper work,saturated soil including blasting soft/hard rock, chiseling soft/hard rock where blasting is prohibited in all lifts including trimming and dressing of sides, levelling of bed, stacking the excavated soil clear from the edge of excavation and then returning the excavated soil in 15 cm. layers when required into plinths,side of foundations etc including consolidating each deposited layer by ramming , watering and then disposing of all surplus excavated soil as directed in all leads/lifts and shoring strutting, timbering and dewatering where ever required as per direction & entire satisfaction of the Engineer-in-Charge. All kind of soil (at STP work).

Excavation in foundation and trenches etc. in earth work lift up to 1.5 mtrs, stacking the excavated soil not more than 3 meters away from the edge of excavation and then returning the stacked soil in 15 cm layers when required into plinths, side of foundations etc including consolidating each deposited layer by ramming, watering and then disposing of all surplus excavated soil as directed in all lead of 20 mtrs complete in all respect as per the direction and satisfaction of Engineer-in-Charge. All kind of Soil (for pipes & man hole Chamber Work)

Providing & laying cement concrete 1:6:12 (1 cement : 6 sand: 12 graded stone aggregate 40 mm nominal size) and curing complete excluding cost of form work in : foundation and plinth including carriage of material complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) complete in all respect with in all leads & lifts as per direction & entire satisfaction of the Engineer-in-Charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) complete in all respect with in all leads & lifts as per direction & entire satisfaction of the Engineer-in-Charge.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including carriage of material complete in all respect with in all leads & lifts as per direction & entire satisfaction of the Engineer-in-Charge.

Providing and laying cement concrete in M 30 grade but not leaner than 1:1:2 (1 cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size) and curing complete excluding cost of form work and reinforcement & reinforced concrete work in:-

Foundation & Plinth including carriage of material complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Walls (any thickness but not less than 0.10 m thickness) including attached butteresses, pillaster plinth and string coursess etc. from top of foundation level upto floor two level including carriage of materialcomplete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :1:1½:3 (1 Cement: 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) including carriage of material complete in all respect with in all leads & lifts as per direction & entire satisfaction of the Engineer-in-Charge.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :1:1½:3 (1 Cement: 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size) including carriage of material complete in all respect with in all leads & lifts as per direction & entire satisfaction of the Engineer-in-Charge.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15˚ landings, balconies, shelves, chajjas, lintels, bands, plain windows sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) including carriage of material complete in all respect with in all leads & lifts as per direction & entire satisfaction of the Engineer-in-Charge.

Providing & laying cement concrete in retaining walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc. up to floor five level, excluding the cost of centering, shuttering and finishing : 1:5:10 (1 Cement: 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) including carriage of material complete with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level and above including carriage of material complete in all respect with in all leads & lifts as per direction & entire satisfaction of the Engineer-in-Charge.

Centering and shuttering including strutting, propping etc. and removal of form for all heights :

Foundations, footings, bases of columns etc. for mass concrete including carriage of material complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Lintels, beams, plinth beams, girders, bressumers and cantilevers including carriage of material complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Walls (any thickness) including attached butteresses, pillaster plinth and string courses etc. from top of foundation level upto floor two level including carriage of material complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Suspended Floor roofs, landing and shelves and their support balconies, beams, girders, bressumers and cantilever including carriage of material complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Arches, domes, vaults up to 6 m span including carriage of material complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Providing, laying, jointing, testing and carriage in trenches Centrifugally cast (spun) ductile iron pipes conforming to BIS 8329-2000 (latest with upto date ammendments) in a length of 5.50 meters class K7 with cement mortor lining in side duly ISI marked including cost of Tyton (push or joints) fittings including testing of joints and rubber gasket (S&R quality) conforming to IS-92820-1989 (Earth work in trenches to be measured and paid for separately) complete in all respect with in all leads and lifts as per direction of the Engineer-in-Charge.

Inlet Pipe 150 mm dia

Outlet Pipe 150 mm dia

Scour Pipe 150 mm dia

150 mm dia

Providing, supplying and fixing of Cast Iron sluice valve of BIR/ Leader make(with hand wheel) as per IS 780 class-I upto 80 mm dia (including brass spindle and as per IS:2906 class-II) for diameters more than 80 mm complete with bolts, nuts, rubber insertion etc. (The tail piece if required shall be measured and paid for separately) including carriage of material complete in all respect with in all leads and lifts as per direction and best satisfaction of Engineer-in-Charge.

Inlet valve 150 mm dia

Supply valve 150 mm dia

Scour valve 150 mm dia

Steel work welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of red lead paint In gratings framed guard bars, ladders, railling, brackets and similar works including carriage of material complete in all respect with in all leads and lifts as per direction and best satisfaction of Engineer-in-Charge.

Providing and fixing of wire gauge using galvanised M.S wire gauge of IS gauge designation 85 G. with wire of dia 0.56 mm for Ventilator of tank including carriage of material complete in all respect with in all leads and lifts as per direction and best satisfaction of Engineer-in-Charge.

Providing and fixing of precast concrete man hole cover and frame, conforming to IS-12593-Part-I 1888 and IS-12592-Part-II, 1991, 560 mm diameter (Heavy Duty Circular) complete in all respect with in all leads and lifts as per direction and best satisfaction of Engineer-in-Charge.

Providing and fixing of 200 mm wide Cast Iron Rungs with chequered or ribbed non slip surface including fixing in manhole with 200x200x100 mm, cement concrete 1:3:6 (1 cement: 3 sand: 6 graded stone aggregate 20 mm nominal size) including carriage of material complete in all respect with in all leads and lifts as per the direction and satisfaction of Engineer-in-Charge.

Manufacturing, supplying, fabrication and fixing of MS Fabricated Protection Pannel 750mm x 750mm made with MS Angle 40x40x4 mm for frame, MS Angle 30x30x3mm for cover, MS Flat 25x5mm for fixing of sliding door bolt and MS Sheet (10 gauge) 3.15mm thick for protection of manhole covers of storage tanks including the cost of cutting and welding of MS Angle, MS Flat & MS Sheet, Embedding in RCC Slab By drilling holes in MS Angle & in RCC Slab, provision for providing and fixing sliding door bolt 300x16mm, MS Handle 100mm, Lock and applying a coat of red lead paint & painting two coat with steel paint (Firroza Blue) complete job in all respect in all leads and lifts and to the entire satisfaction of the Engineer-in-Charge.

Pumping Machinery:- Providing, fixing, testing and commissioning of Non Clog Submersible/Monoblock sewerage pumping set for lifting sludge of reputed make such as KSB/BS/Oswal/ Calama/ Johnsion/ Grundfos/ JSV approved make confirming to latest relevent IS code 5659-1970 or latest edition. The pump should be fitted with free flow bronze impellers or of suitable alloy capable of handling 100 PPM turbudity. The pump shall be directly coupled to a submersible squirrel cage electric induction motor IE2 or above (water proof type) of required HP, RPM 2900 of Kirloskar/ NGEF/ Crompton/ JSV approved make confirming to BIS 9283-2013 latest with up to date ammendments, totally dust & water proof for submersible duty isolated from the pump by intermediate casing with double mechanical seal in oil chamber & grease packed lubricated bearings & provided with stainless steel thrust bearing plate to with stand non vertical loads with minimum wear & tear. It should also be fitted with a device to take up expansion of water with heating of motor. The pump set should include water level guard, errection clamps, cable clip & depth gauge etc. & suitable for operation on data given below:- 4 Set x 25 HP = 100 BHP

SITE CONDITIONS:- Discharge(Q) - 10.37 LPS, Total Dynamic heads - 74.84 mtr., LWL in Sump Well - 1138 mtr., Shaft Level - 1137 mtr., Level at Discharge point - 1207 mtr., Suction Lift - Positive, Discharge Head - 74.84 mtr., Static Head - 70 mtr. Rising Main:- Length - 150 mtr., Dia - 150mm, Pumping Hours - 20 Hrs, Altitude of installation above MSL - 1000 mtr., Characterstics of water - Sludge water with turbudity upto 100mm, Temperature - 25 Degree Centigrade.

Supply, Installation, Testing and Commissioning of Star Delta Starter panel for submersible pump made out of 16 Gauge sheet, powder coated dust and vermin proof, wall/base mounted and front opening door type with copper insulated wiring suitable to operate 4 Nos. pumps (2 working & 2 stand by) each of the rating 25 HP through Star Delta Starter mechanism. Starter should be capable enough to handle the following faults like short circuit, over current, under current, over voltage, under voltage, dry run protection and phase loss with LED ON/OFF & TRIP indicators Of reputated make i.e JSV Approved/ The product should be of Global Brand etc. complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Star, Delta and Mains Power Contactors of required ratings as per type-2 co-ordination for 25 HP starter complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Voltage Protection device to protect panel from over voltage and under voltage complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Single phasing and phase reversal protection device to safeguard system from single phasing and phase reversal of the supply voltage complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Multi function meter indicating different parameters like Current, Voltage, KWH, PF, THD etc with RS 485 communication Make JSV Approved/Global brand etc. complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Main incomer MCCB/MCB of suitable capacity of L&T / Schnieder/ABB make on the feeder for pumping set confirming to BIS 2516-1985 ( Latest edition) complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Individual Starter incomer MCCB/MCB of suitable capacity of L&T / Schnieder/ABB make on the feeder for pumping set confirming to BIS 2516-1985 ( Latest edition) complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Three phase indicating lamps complete with logged switches for individual motors conforming to BIS 3452 ( Part I & II ) latest with upto date ammendments complete in all respect as per the entire satisfaction of Engineer-in- Charge.

LED On / Off & Trip indicator and push buttons, Control and power wiring, Power capacitor, Cooling fan 230 VAC, Contorl terminal, Bus Bar, i.e. Bolt, insulator etc. complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Surge supressor device with Isolating MCCB to eliminate the power surges due to lightening and system surges complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Control Transformer to provide a stable control volatge to safegaurd the control circuit of all the components from the voltage surges and spikes complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Independent Control Panel with Switch Fuse Unit and Fuses of Suitable Amperage to eliminate the KitKat fuses of HPSEB Of reputated make i.e Aarmation/Siemens/Schnieder/L&T etc. complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Providing double flanged cast steel sluice valve, ASA-150 of Leader/ BHEL/ Kirlosker/ Kilburn/ GLEd/ Fourses make and one step higher then delivery line of pump and capable of withstanding normal seat pressure as per BIS standards with upto date ammendments) complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Providing double flanged cast steel reflux valves class, ASA-150 of Leader/ BHEL/ Kirlosker/ Kartar/ Kilburn/ GLEd/ Fourses make for rising main and capable of withstanding normal seat pressure as per BIS standards with upto date ammendments) complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Providing 100mm dia circular dial analog pressure gauge of suitable range of Fiebig /Bourden/ PREGA/ Precision make complete with all accessories such as stop cock, copper tubing etc.as per IS: 3624-1987 with upto date ammendments complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Providing discharge meter of standard make to be fixed on the rising main in pump house as per IS:2373:1981 with upto date ammendments complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Installation of all the items apparing as per the schematic drawing complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Providing and laying copper PVC insulated armoured power cable (One cable carrying all the three phases) of suitable size and capacity to motors and all other electircal equipments as per IS:1554(P-I) 1988 or latest ith upto date ammendments of Siemens/ GLOSTER / IEC/ ICC/ EICO/ NATIONAL/ GRANDLAY make including all other accessories such as thinbles, flexible pipes,solders,nuts and bolts cable glands etc. laid in pipes or trenches under floor complete in all respect as per the entire satisfaction of Engineer-in- Charge.

(a) Motor side (From switch to starter and starter to motor) 3 core cable complete in all respect as per the entire satisfaction of Engineer-in- Charge.

(b) Supply side (From Meter of HPSEB to bus bar and switch) 3.5 core cable complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Providing and fixing double loop earthing with GI plate 600mmx600x3mm thick electrode complete with material such thimbles nuts and charcoal and common salt, 25mmx5mm copper strips as per IS:3043:1987 with upto date ammendments for motors and other electrical equipments and digging of pits etc. complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Providing and fixing of double flanged MS/GI piping work (layout to be approved by the ENC) for suction and delivery pipes suitable to pumps offered as per the R/Main respectively complete with all specials such as bends, tees, reducers, increasers with companions flanges matching with the relevant specifications of the accessories including rubber/ asbestos gasket of minimum 3mm thickness as per IS-1364:1983. The pipe fittings and joints shall be as per relevant IS code & to withstand 1.5 times total head stipulated under item no. 1. The size of the various components to be as under:-

Suction pipe: One dia higher than the suction of pump offered and suitable to keep the velocity of flow from 1 to 1.5 m/sec in the suction pipe.

Delivery pipe: One dia higher than the delivery of pump offered and suitable to keep the velocity of flow from 1.5 to 2 m/sec in the delivery pipe.

Low Cost Automation :- PLC (Programmable logic controller) with appropriate digital and analog inputs and outputs to give automatic command to Star Delta Starter Panel/ Energy Saving Variable Frequency Starter Panel Make- Aarmation Electric/ Bechoff Automation/ Rockwell Automation/ JSV Approved complete in all respect.

Electronic relay card 8 channel complete in all respect.

SMPS 4.5 Amps to energise PLC system complete in all respect.

HMI (Human Machine Interface) 7" display for Monitoring and Controlling of Centrifugal pumps Make: JSV Approved/ Bechoff Automation/ Rockwell Automationcomplete in all respect.

Control MCB for Automation System complete in all respect.

Level Sensor to indicate the water level of tank remotely complete in all respect.

Shielded Data Cable for Communication of Level Sensor with PLC complete in all respect.

Gaseous Chlorination :- Upgradation by the way of conversion from extended aeration to MBBR unit (one unit only of size 8.0 x 8.0 m) of existing 0.35 MLD STP Rewalsar, which consists of Providing, Installation, Testing and Commissioning of Fine bubble deffused aeration system tubular type, Diffusers, Diffusers grid system, MBBR Membrane, MBBR Media including all kind of piping, valves, cables, pressure gauges, PLC Panels, Electric panels etc to make the system fully functional to the entire satisfaction of Engineer-in-Charge. Item is inclusive of Providing, installation of 2 nos. Air blower (one working and 01 standby) of designed capacity including all piping, valves, cables, wiring, Electric panels etc to make the system fully functional complete in all respect as per the entire satisfaction of Engineer-in- Charge.

Providing, Installation, Testing and Commissioning of Vaccum type floor mounted Gaseous chlorination system with two no. chlorinator and tonners a/w leak detection system including level switches, all piping, cable, dozing pump, electric panels etc to to make the system fully functional complete in all respect as per the entire satisfaction of Engineer-in-Charge.