PROVN OF GEN SET OF 15 KVA, 40 KVA AND 20 KVA FOR PET PL ASC, ARMY AVN AND RPA FIT UNDER GE MISSAMARI

Amount

Surface dressing in soft loose soil n exc 15 cm deep and getting out

Excavation in trenches n exc 1.5 m width and n.exc 1.5m depth for foundation in soft/loose soil & getting out complete all as specified and as directed.

Returning and filling in, including spreading, levelling, watering, well ramming in layers not exc 25 Cm thick complete all as specified and as directed.

Removing of excavated materials not exceeding 50 metre and depositing where directed by Engr in Charge at a level not exceeding 1.5 metre above the starting point.

Excavating in post holes (or similar holes) each n exc 0.5 cum,in Hard/dense soil and getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and directed.

M&L for PCC of type B2 1:2:4 ( 40 mm graded agrgregate) cement concrete in foundation/ road filling complete all as specified and directed.

M&L for brick work with burnt old size bricks built in cement mortar 1:6 straight or curved on plan exceeding 6mtr mean radius and all as directed.

M&L for broken stone or boulders of hardcore of gauge n exc 63 mm deposited, spread and levelled in layers n exc 15 cm thick watered and rammed to a true surface.

M & L Clean dry river sand in trenches/ducts for cushioning to cable, 8 cm in depth before laying the cable and 15 cm in depth after laying the cable complete all as specified.

M&L for 100mm thick PCC type B2 1:2:3 using (40mm gradded aggregate) as Hardstanding/ Sub base

M&L rendering 15mm thick on other than fair faces of brick or concrete Surfaces in cement mortar 1:6 finished even and smooth.

S&F pre painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws as specified.

S&F pre painted galvatume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws as specified.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161 1979 grade St.-240 conforming to Fe-410-W Gde E-250 quality -A

M&l Painting two coats of synthetic enamel paint over a coat of red oxide primer to new steel Surfaces of any description, not otherwise described, over 10cm width or girth.

Supplying, installing, commissioning and testing complete of static Silent Diesel Engine Driven Generating set comprising standard AMF panel capable of delivering 15 KVA, 415 Volts (AC 3 Phase, 4 wire system of supply) 50 Hz at power factor 0.8 minimum type A (standard AMF Panel CPCB IV+). The DG set shall consist of a diesel engine coupled through flexible coupling to a matching alternatore and mounted on dunlop metallastik foundation pads on a common base frame and thereafter installed in the CPCB approved acoustic enclosure (the complete set conforming to and test certified as per CPCB norms and as specified) all as specified complete with control panel standardised by manufacturer, flexible exhaust pipe complete and shall comprise of the followings :- Make : Kirloskar KOEL, Cummins, Ashoka leyland, Sudhir. (a) ENGINE (PRIME MOVER) : Diesel Engine 1500 RPM of suitable HP as recommended by manufacturer but not less than 20.9 BHP (at NTP) water cooled, Turbocharged aircooled, 2 x 180 AH 12 volts electric battery start, complete with fly wheel and all standard fittings/fixtures as per manufacturing practice including suitable engine control panel with tachometer, lub oil temp & pressure gauge, water temp gauge and frequency meter (digital type) including safety shutdown contents and also including self starter, dynamo, fuel tank etc and conforming to IS : 10002, ISO : 3046, BS-5514. The engine shall give electrical out put of 15 KVA at 0.8 PF. (b) ALTERNATOR : AC alternator, self excited, self regulaed, self ventilated, brushless design, conforming to BS 2613/IS 4722, 3 Phase, 415 Volts, 50 Hz, 4 wire system output 200 KVA PF 0.8 1500 RPM insulation class 'H' enclosure IP 23/TEFC complete with AVR with +/- 1% voltage regulation directly coupled to and match the above engine and capable for over load of 10% for one hr in 12 hr operation. (c) Dunlop Metallastic anti-vibration pads for mounting engine - alternator assembly on the base frame/plate. (d) BASE FRAME : Made out of structural steel as per Manufacturer's recommended design/specification. (e) ACOUSTIC ENCLOSURE : Provn of an integral type approved/certified acoustic enclosure as per CPCB norms for the DG sets restricted the noise level to 75 db at one meter along and temp rise within canopy shall not exceed 5 degree to 7 degree celsius. It shall be made of 16 SWG CRCA MS sheet with powder coated finish on outside and provided with non igniting fire retardant foam as accoustic material. There shall be four hinged doors out of which one shall be with a glass window. The base frame shall be ISM section. It shall also include the following :- (i) Silence absorption type, non-resistance, residential and exhaust pipe covered with asbestos rope lagging extending to about 2 mtrs outside the acoustic enclosures. (ii) Internal wiring with PVC copper conductor cables, IS-694 marked, FRLS in conduit and flourescent lamp fittings. (f) Battery 2 Nos 12 V x 180 AH DC charged/sealed maint free of suitable cap all inclusive of engine/alternator protective foundation with LCD display. Make : EXIDE/AMCO (g) Control Panel (h) Foundation of DG Set shall be as per Manufacturer's recommendation. Essential : Panel/DG (AMF) Panel shall be comprising of the following :- (j) CATALOGUES : Operation and Maintenance manual, spare parts list, overhauling manual - 03 Sets. Note :- All outgoint feeders shall be connected by cable through suitable size gland palte/glands.

Supplying, installing, commissioning and testing complete of manufacturer of OEM (Original Eqpt Manufacturer) manufactured and tested static Silent Diesel Engine Driven Generating Set including standard panel capable of delivering 40 KVA, 415 volts (AC 3 Phase, 4 wire system of supply) 50 Hz at power factor 0.8 minimum. The DG set shall consist of a diesel engine coupled through flexible coupling to a matching alternator and mounted on Dunlop metalastik foundation pads on a common base frame and threafter installed in the CPCB approved acoustic enclosure (the complete set conforming to and test certified as per CPCB IV+ norms and as specified) all as specified complete with control panel standardised by manufacturer, flexible exhaust pipe complete including PCC foundation of suitable size as per manufacturer reccomendation and shall comprise of the followings :- Make:- KOEL/ASHOK LEYLAND/SUDHIR/ CUMMINS (a) ENGINE (PRIME MOVER). Diesel Engine 1500 RPM of suitbale HP as recommended by manufacturer but not less than 56 BHP (at NTP) water cooled, Turbocharged aircooled, 1x 150 AH 12 Volts electric battery start, complete with fly wheel and all standard fittings/fixtures as per manufacturing practice including suitable engine control panel with tachometer, lube oil temp & pressure gauge, water temp guage and frequency meter (digital type) including safety shutdown contents) and also including self starter, dynamo, fuel tank etc and conforming to I.S. 10002, ISO 3046, BS-5514. The engine shall give electrical out put of 40 KVA at 0.8 PF. (b) ALTERNATOR. AC alternator, self excited, self regulated, self ventilated, brushless design, conforming to BS 2613/IS 4722, 3 Phase, 415 volts, 50 Hz, 4 wire system output 40 KVA PF 0.8 1500 RPM insulation class `H' enclosure IP 23/TEFC complete with AVR with + 1% voltage regulation directly coupled to and match the above engine and capable for over load of 10% for one hr in 12 hr operation. (c) Dunlop Metalastik anti-vibration pads for mounting engine - alternator assembly on the base frame/plate. (d) BASE FRAME. Made out of structural steel as per Manufacturer's recommended design/specefications. (e) ACCOUSTIC ENCLOSURE. Provn of an integral type approved/certified acoustic enclosure as per CPCB IV+ norms for the DG sets restricted the noise level to 75 db at one meter along and temp rise within canopy shall not exceed 5° to 7° Celsius. It shall be made of 16 SWG CRCA MS sheet with powder coated finish on outside and provided with non igniting fire retardant foam as accustic material. There shall be four hinged doors out of which one shall be with a glass window. The base frame shall be ISM section. It shall also include the followings:- (i) Silence absorption type, non-resistance, residential and exhaust pipe covered with asbestos rope lagging extending to about 2 mtrs outside the accoustic enclosures. (ii) Internal wiring with PVC copper conductor cables, IS 694 marked, FRLS in conduit and flourescent lamp fittings. (f) Battery 1 Nos 12 V x 150 AH DC charged/sealed maint free of suitable cap all inclusive of engine/alternator protective foundation with LCD display. Make : EXIDE/AMCO (g) Control Panel (h) Foundation of DG set shall be as per Manufacturer's Recommendation . Note :- All outgoing feeders cables shall be connected through suitable size gland palte/glands.

Supplying, installing, commissioning and testing complete of manufacturer of OEM (Original Eqpt Manufacturer) manufactured and tested static Silent Diesel Engine Driven Generating Set including standard panel capable of delivering 20 KVA CPCB IV+, 230 volts (AC 1 Phase, 2 wire system of supply) 50 Hz at power factor 0.8 minimum. The DG set shall consist of a diesel engine coupled through flexible coupling to a matching alternator on a common base frame and threafter installed in the CPCB approved acoustic enclosure (the complete set conforming to and test certified as per CPCB norms and as specified) all as specified complete with control panel standardised by manufacturer, flexible exhaust pipe complete including PCC foundation of suitable size as per manufacturer reccomendation and shall comprise of the followings :- Make:- KOEL/ASHOK LEYLAND/SUDHIR/ CUMMINS (a) ENGINE (PRIME MOVER). Diesel Engine 1500 RPM of suitbale HP as recommended by manufacturer but not less than 25.5 BHP (at NTP) water cooled, Turbocharged aircooled,1x 65 AH 12 Volts electric battery start, complete with fly wheel and all standard fittings/fixtures as per manufacturing practice including suitable engine control panel with tachometer, lube oil temp & pressure gauge, water temp guage and frequency meter (digital type) including safety shutdown contents) and also including self starter, dynamo, fuel tank etc and conforming to I.S. 10002, ISO 3046, BS-5514. The engine shall give electrical out put of 20 KVA at 0.8 PF. (b) ALTERNATOR. AC alternator, self excited, self regulated, self ventilated, brushless design, conforming to BS 2613/IS 4722, 1 Phase, 230 volts, 50 Hz, 2 wire system output 20 KVA PF 0.8 1500 RPM insulation class `H' enclosure IP 23/TEFC complete with AVR with + 1% voltage regulation directly coupled to and match the above engine and capable for over load of 10% for one hr in 12 hr operation. (c) BASE FRAME. Made out of structural steel as per Manufacturer's recommended design/specefications. (d) ACCOUSTIC ENCLOSURE. Provn of an integral type approved/certified acoustic enclosure as per CPCB norms for the DG sets restricted the noise level to 75 db at one meter along and temp rise within canopy shall not exceed 5° to 7° Celsius. It shall be made of 16 SWG CRCA MS sheet with powder coated finish on outside and provided with non igniting fire retardant foam as accustic material. There shall be four hinged doors out of which one shall be with a glass window. The base frame shall be ISM section. It shall also include the followings:- (i) Silence absorption type, non-resistance, residential and exhaust pipe covered with asbestos rope lagging extending to about 2 mtrs outside the accoustic enclosures. (ii) Internal wiring with PVC copper conductor cables, IS 694 marked, FRLS in conduit and flourescent lamp fittings. (e) Battery 1 Nos 12 V x 65 AH DC charged/sealed maint free of suitable cap all inclusive of engine/alternator protective foundation. Make : EXIDE/AMCO (f) Control Panel (g) Foundation of DG set shall be as per Manufacturer's Recommendation . (h) CATALOGUES. Operation and Maintenance manual, spare parts list, overhauling manual - 01 Sets Note :- All outgoing feeders cables shall be connected through suitable size gland palte/glands.

M & L for onload change over switch of capacity 63 A (Side handle) in sheet metal encloser, 415 V, 50Hz, 4 P compete all as specified

Supply and laying well burnt Bricks, locally available best quality (sub class "B" bricks) laid in trenches perpendicular to U/G cable for cable protection complete all as specified.

Supply & Laying LT heavy duty UG Cable of size 25 Sqmm 3.5 Core laid in trences /floor/on wall/service connection XLPE Insulated, sheathing and armd 1100 Volts grade with aluminium conductor including connection to the main Lt panel with necessary lugs, gland packing etc after cutting to required length complete all as specified and directed. Make :- Polycab and equivalent in Havells and KEI

Supply & laying LT UG XLPE sheathed PVC insulated, screened PVC bedded, Galvanised Steel Strip of Wire armoured electric power cable heavy duty with stranded Aluminium Conductor 1100 Volt grade, laid in trenches/ surface of Wall/in GI Pipe along with Pole for connection to OH Lines including brass cable glands mild fteel flat iron clamps etc and testing for following sizes, complete all as specified and as directed. Note : Earthworks, Sand Cushioning, Bricks, GI Pipe etc. will be measured and paid under appropriate Items. (a) 3.5 core x 50 Sqmm

(b) 3.5 core x 35 Sqmm

(c) 3.5 core x 400 Sqmm

(d) 2 core x 35 Sqmm

Earthing complete with galvanised steel earth plate electrode 60×60cm×6mm thick, buried directly in ground vertically in a pit of depth not less than 2.25 metres deep below ground level with top edge of the plate not less than 1.5 metres below normal ground level surrounded from all sides by mixture of charcoal and common salt and electrode connected to and including galvanised iron strip 32 x 6 mm means of bolts, nuts, check nuts and washers of galvanised iron or steel and GI pipe light grade 20 mm dia bore for watering funnel with wire mesh refilling with vegetable soil without bolders and stone, gravels and aggregate etc., and CI cover with frame, PCC 1:3:6 type C-2 excavation and earth work all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion. Notes : The unit rate includes for protection pipe and GI wire dia from top of earth plate up to 7.00 meter above ground level.

M&L for Earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground earth pit not less than 2.25mtr deep below normal ground level with top edge of the plate not less than 1.5 mtr below ground level connected to galvanized iron strip 25 x 4 mm as earthing lead by mean of nut/bolt and washer of galvanized iron or steel drawn through 40 mm dia light grade GI pipe as shown in electrical plate no 3 of SSR part I of 2009 including necessary excavation and earth work GI pipe 20mm dia light grade for watering PCC chamber with PCC cover in cement concrete 1:2:4 Type B1(20mm graded aggregate), funnel, wire mesh, charcoal dust, salt etc, connected to panel board / Gen Set as indicated including testing complete.

M&L for Earthing complete with copper earth plate electrode 600 x 600 x 6 mm thick buried directly in ground earth pit not less than 2.25mtr deep below normal ground level with top edge of the plate not less than 1.5 mtr below ground level connected to copper strip 20 x 3 mm as earthing lead by mean of nut/bolt and washer of galvanized iron or steel drawn through 40 mm dia light grade GI pipe as shown in electrical plate no 3 of SSR part I of 2009 including necessary excavation and earth work GI pipe 20mm dia light grade for watering PCC chamber with PCC cover in cement concrete 1:2:4 Type B1(20mm graded aggregate), funnel, wire mesh, charcoal dust, salt etc, connected to panel board / Gen Set as indicated including testing complete.

M & L for onload change over switch of capacity 400 A (Side handle) insheet metal encloser, 415 V, 50Hz, 4 P compete all as specified

PURBANCHAL BUILDERS (BID ID -3374484)

M/S Krishna Construction Co. (BID ID -3373503)

M/S K.K.TRADERS (BID ID -3374745)

S M STORE (BID ID -3373071)

M/s JK Jangid and Company (BID ID -3374254)

M/s Dhani Enterprise (BID ID -3374150)

R K ENGINEERING ASSEMBLE (BID ID -3374392)