GENERAL-KIP(LBMC) mechanical work-Fabrication, painting ,providing hoisting mechanism and erection of 3 Nos cross regulator shutter at sadanandhapuram ch 30190 in LBMC-General Mechanical Work

Amount

Cleaning of work site, dismantling the old damaged mechanical structures, demolishing the existing civil structure and providing concrete for fixing new embedded parts etc.

OD3300/2025-2026:Clearing grass from banks of canal and removal of silt, zoological waste and other debris from canal bed including removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared

OD3866/2025-2026:Bailing out water using pump above 5 HP and Up to 10 HP-Bailing out water with engine and pump set above 5HP and up to 10HP, including conveyance to site and erection, cost of fuel, lubrication oil, and other stores pay of staff, etc complete

OD3867/2025-2026:RING BUND Type-I-Putting up ring bund as per approved shape 2.5m bottom width, 1m top width using empty gunny/polythene bags filled with earth placed in 2 rows at 0.6m apart and filled in between with puddle clay to form bund for an average height 2.00m including labour dismantling the bund after completion of the work, etc. complete. Vol. of bund (1+2.5)/2*2*20=70m3 Vol of core 0.6*2*20 = 24m3 vol of earth 70-24 = 46m3 No. of bags 46/0.027 =1704nos

OD3301/2025-2026:Dismantling of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting Unit / Embedded parts etc. of the same and stacking at a distance of 100 meter including hire of machinery labour etc. complete as directed by the departmental officer at the site. (weight of the unserviceable shutters and embedded parts may be calculated as 60% and unserviceable hoisting units as 80 % )

15.2.1:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

5.9.6:Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts

5.8:Reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers, facias and eaves boards up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with 1:11/2:3 (1 cement : 11/2 coarse sand derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

Supply,Fabrication & fixing of new embedded parts.

OD3296/2025-2026:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

OD3298/2025-2026:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

OD3295/2025-2026:Supply of MS round bar including cost of conveyance charges

OD3297/2025-2026:Fabrication and erection of Embedded parts for canal shutters ( Up to 2 tonne weight ) and accessories as per approved specifications, drawings and directions of deptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied

OD3299/2025-2026:Fabrication, Supply, erection and assembling of wheel track, sill seat and seal track in correct position and alignment by welding SS Embedded parts in 304L Grade as per approved specifications, drawings and directions of deptl officer at site including cost of all materials, labour, welding, shearing, grinding etc,lead and lift, conveyance, incidental and handling etc complete.

Supply,fabrication and painting of shutters( 3nos), Supply and fixing of rubber seals, new shutter rollers and erection of shutter

OD3281/2025-2026:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

OD3283/2025-2026:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

OD3282/2025-2026:Supply of M.S Bolt with nut and washer

OD3280/2025-2026:Fabrication and supply of Structural steel canal shutters ( Up to 2 tonne weight )/Hoisting Bridge /Platfurm and accessories etc. for the same as per approved specifications, drawings and directions of deptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied

85.114:Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

OD3302/2025-2026:Supply and fixing of Bush type CS Roller having OD 130mm x ID 55mm x thread width 50mmwith Al Bronzel bush OD 55xID40xwidth50 and SS shaft Dia 40 x 100L including cost of allmaterials, labour ,incidental and conveyance charges etc. complete

OD3284/2025-2026:Supplying and fixing in correct position with specified initial interface L-type/Bulbnose rubber seal confirming to IS 11855 to the canal shutters including cost of MS bolts and nuts ,all labour, machinery, incidental and conveyance chargers complete as per approved specification and drawing

OD3286/2025-2026:Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the canal gates including cost of MS bolts and nuts, all labour and machinery and incidental and conveyance chargers complete as per approved specification and drawing.

OD3285/2025-2026:Erection of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting Bridge / Platform including hand rails , ladder etc. for the same including . alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance , lead and lift charges etc complete but excluding cost of materials already supplied.

Replacing Hoisting mechanism and platform, conducting trial run

OD3294/2025-2026:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

OD3292/2025-2026:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

OD3291/2025-2026:Fabrication and supply of Structural steel canal shutters ( Up to 2 tonne weight )/Hoisting Bridge /Platfurm and accessories etc. for the same as per approved specifications, drawings and directions of deptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied

85.115:Cost of painting with 2 coats of enamel paint over 1 coat of zinchromate primer as per IS1477:1994 after hand and power tool cleaning including cost of all materials, labour charges, cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

OD3290/2025-2026:Providing EN 8 screw rod 7.50 tonn capacity 4.00M lift screw hoist having one number of EN 8 screw shaft having a lifting speed of around 5cm/ min for 24 rpm of hand operation including cost of all materials, hire charges and conveyance (67mm dia)

OD3293/2025-2026:Providing of worm and pinion having a lifting speed of around 5.00 cm/min for hand operation including costof all materials, labour, hire charges and conveyance

OD3289/2025-2026:Erection of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting Bridge / Platform including hand rails , ladder etc. for the same including . alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance , lead and lift charges etc complete but excluding cost of materials already supplied.

OD3288/2025-2026:Trail run the gates with its hoisting mechanism etc. including cost of all materials, machinery , labour, all lift and lead, incidental and conveyance charges etc. As per instruction of departmental officers in charge

OD3303/2025-2026:SUPPLYING and APPLYING GREASE on NEW SCREW ROD for CANAL GATE

JOBIN JOSEPH (BID ID -2348516)

Bidder Name

SAI ENGINEERING

JOBIN JOSEPH