ADDN/ ALTN AND SPECIAL REPAIR TO NHQ BLDG NO 165 AT EME SCHOOL VADODARA

Amount

Demolition of stone slabs and tiles of any description or thickness in floors and aprons laid, bedded and pointed in any mortar and removing from site complete all as specified and as directed.

Material and labour for roughening surface of old concrete by picking, sweeping clean and washing down with water to remove all loose dust complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floor and pavings not exceeding 15 cm thickness (below or above ground level) and removing from site complete all as specified and as directed.

Material and labour for 25mm thick PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) in sub floors complete all as specified and as directed.

Material and labour for joint free coloured (of any shade) vitrified ceramic tiles 9 to 10mm thick (square/ rectangular) polished, double charged, area of each tile not exceeding 0.36 sqm, in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match including screed bed or bedding layer of mortar 15mm thick for laying floor fiishes with CM 1:4 complete all as specified and as directed.

Material and labour for joint free coloured (of any shade) vitrified ceramic tiles 9 to 10mm thick (square/ rectangular) polished, double charged, area of each tile not exceeding 0.36 sqm, in skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick rendering for backing coat on vertical surface of wall or concrete surfaces in CM 1:3 to receive wall tiles complete all as specified and as directed.

Material and labour for joint free non skid ceramic tiles, coloured, 7 to 8 mm thick (square/ rectangular) in floors area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed.

Material and labour for joint free non skid ceramic tiles, coloured, 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, on vertical surfaces such as skirtings, dados and risers to steps, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:3 on stone masonry surfaces/ brick work or concrete surfaces complete all as specified and as directed.

Material and labour for non skid ceramic tiles, coloured, 7 to 8mm thick (square/ rectangular) in floors area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in CM 1:4 (Tile pattern and decoration shall be as directed by Engineer-in-charge) complete all as specified and as directed.

Material and labour for glazed ceramic tiles, coloured, 450 x 300 x 7mm thick on vertical surfaces such as skirting, dados and risers to steps, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:3 on stone masonry surface/ brick work or concrete surface. (Tile pattern and decoration shall be as directed by Engineer in-Charge.) complete all as specified and as directed.

Material and labour for 18 to 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) 10mm thick backing/ Screed including pointing in white cement (1:2) using marble dust with admixture of pigment to match complete all as specified and as directed. Note:- Shade of granite shall be as approved by Engr-in-Charge/ GE.

Rounding to edges of stone slabs such as steps cooking platefrom and other similar situations complete all as specified and as directed.

Material and labour for machine cut kota stone slab 20-25mm thick in flooring over and including 15mm thick cement screed bed or bedding layer in CM 1:4 mixed with high performance adhesive as per manufacturers instructions, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed. Note:- High performance adhesive shall be measured and paid for separetely as "Supply only".

Material and labour for kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over and including 10mm thick rendering in CM 1:3 on stone masonry surfaces/ brick work or concrete surfaces mixed with high performance adhesive as per manufacturers instructions and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed. Note:- High performance adhesive shall be measured and paid for separetely as "Supply only".

Demolition of cement concrete (reinforced) (reinforcement cut as required to facilitate demolition) roofs, floors (other than ground floors), beams, stair cases, landing, chajjas and similar suspended work and removing from site complete all as specified and as directed.

Provision and application of approved epoxy based bond coat on concrete surfaces or sound bonding of cold and new concrete surfaces according to instructions of Engineer-in-Charge.

Material and labour for super fluid micro concrete-roffe crete repairs (or equivalent as specified in the list of brand names) in beam bottoms, columns, slabs including mixing with 5mm to 10mm size aggregates, consolidating, curing complete as per manufacturer's specifications and consultants instructions. Note:- This item shall be measured and paid for on the actual consumption of micro concrete.

Making of profile of structural memebers with polymer modified mortar in damaged areas 1:3 (Cement:sand) mortar with 5 -10 percentage addition of latex polymer, w/c ratio of 0.35 in 20mm thick layers/ including leveling complete all as specified and as directed.

Material and labour for cement concrete (1:2:4) type B-1 (using 20mm graded stone aggregate) as in floors any thickness in platform for PVC tank and similar work complete all as specified and as directed.

Taking down cement plaster, any description on brick, concrete or stone walls or ceiling including racking out joints, hacking for key, scrubbing down with water and removal of rubbish off complete all as specified and as directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars and removing from site complete all as specified and as directed.

Material and labour for brick work with sub class 'B’ bricks using old size bricks, straight or curved on plan exceeding 6 meter mean radius, built in CM 1:6 complete all as specified and as directed.

Material and labour for brick work with sub class 'B’ bricks, old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed.

Material and labour for rendering 10mm thick in CM 1:6 on brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for rendering 5mm thick in CM 1:4 mixed with liquid water proofing compound @ 0.200 litre per bag of 50 kg of cement, over and including 10mm thick rendering in CM 1:6 on brick work or concrete surfaces. Note:- Liquid water proofing compound shall be measured and paid for separately as “Supply only”.

Material and labour for rendering 5mm thick in CM 1:3 on concrete surfaces in ceiling (facia/ ceiling/ edging of chajjas and roof projection) including finishing even and smooth without using extra cement complete all as specified and as directed.

Material and labour for preparation of new plastered or unplastered surfaces of walls and applying two coats of distemper oil emulsion, white or tinted, over and including one coat of average 1 to 2mm thick Birla/ JK wall care putty over one coat of primer complete all as specified and as directed.

Material and labour for complete removal of existing treatment from walls and applying two coats of distemper oil emulsion, white or tinted, over and including one coat of average 1 to 2mm thick Birla/ JK wall care putty over one coat of primer complete all as specified and as directed.

Material and labour for preparation of newly plastered or unplastered surfaces of ceilings and applying three coats of white wash complete all as specified and as directed.

Material and labour for complete removal of existing treatment on old plastered or unplastered surfaces of ceilings and applying three coats of white wash complete all as specified and as directed.

Material and labour for applying two coats of damp proof waterproofing coating @ 2.7–3.2 m2/L/coat over new plastered surface of exterior wall complete all as per manufacturer instuctions complete all as specified and as directed. Note:- (i) Damp proof coat applied to wall surface before exterior emulsion paint. (ii) Make of damp proof paint and weather coat paint shall be same.

Material and labour for preparation of newly plastered surfaces of walls/ ceilings of roof projection and chajjas and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/ litre and UV resistance as per IS 15489:2004, Alkali and fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old/ new surfaces complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 sqm each and removing from site complete all as specified and as directed. Note:- Quoted rate shall be deemed to be include for cutting holes/ demolition of PCC block/ brick work for taking down chowkats and making good the damaged surfaces in CM 1:3.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 sqm but not exceeding 4 sqm each and removing from site complete all as specified and as directed. Note:- Quoted rate shall be deemed to be include for cutting holes/ demolition of PCC block/ brick work for taking down chowkats and making good the damaged surfaces in CM 1:3.

Supply and fixing 35mm thick flush shutters, solid core construction, with block board core, both faces covered with decorative prelaminated work with 6mm thick teak wood edging all round complete all as specified and as directed.

Supply and fixing aluminium powder coated of any colour (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing complete all as specified and as directed.

Supply and fixing of Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows and ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge complete all as specified and as directed.

Supply and fixing sheet glass 4mm thick, ordinary quality and glazing with neoprene beading in square exceeding 0.5 sqm in each pane complete all as specified and as directed.

Supply and fixing sheet glass 4mm thick, figured glass, pin headed type and glazing with neoprene beading in square not exceeding 0.5 sqm in each pane complete all as specified and as directed.

Supply and fixing stainless steel wire cloth, 0.36 nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beads supplied with shutters complete all as specified and as directed.

Supply and fixing mild steel of grade Fe-290 (Grade E-165) in bands, straps, supports or stays for rain water, ventilating pipes including bolts, if required, clamps, hold fasts and similar small articles complete all as specified and as directed.

Material and labour for PCC 1:3:6 type C-0 using 12.5mm graded stone aggregate in cills, steps, bands, copings, bed plates, blocks for inserting hold fasts, filling back of chowkats and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed.

Material and labour for 100mm butt hinges of stainless steel grade 202, 14 gauge thickness, medium weight of approved make fixed with pressed steel door frame/ Angle iron frame/ PVC door frame with screw complete all as specified and as directed.

Material and labour for 75mm butt hinges of stainless steel grade 202, 14 gauge thickness, medium weight of approved make fixed with pressed steel door frame/ Angle iron frame/ PVC door frame with screw complete all as specified and as directed.

Supply and fixing 200mm long aluminium, anodized, barrel tower bolts of extruded section and fixed complete all as specified and as directed.

Supply and fixing 150mm size extruded aluminium alloy handles, fabricated type, anodized complete all as specified and as directed.

Supply and fixing hasp and staple of size 75mm, safety type, aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed.

Supply and fixing 150mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

Supply and fixing 250mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and as directed.

Supply and fixing factory made single extruded WPC (Wood polymer composite) solid door Frame/ Chowkhat comprising of 62mm x 32mm size applying PVC solvent cement and screwed with full body threaded star headed stainless steel screws having minimum frame density of 750 KG/ Cum and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed in position with mild steel hold fast/ stainless steel dash fasteners of required dia and length complete all as specified and as directed.

Supply and fixing factory made 28-30mm thick single extruded WPC (Wood polymer composite) solid panel both side prelaminated flush door shutter of required size modulus of elasticity 850 N/mm^2 and resistance to spread of flame of class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk stainless steel screws complete all as specified and as directed.

Supply and fixing in repair 18mm thick HDHMR BOARD exterior grade including any coloured prelaminated sheet of required thickness over HDHMR board, anti fungal, moisture resistance, anti borer as per IS 14587 for frame and shutter for kitchen cabinets/ cupboards complete all as per specified and as directed by Engr-in-Charge. Make: Action Tessa/ Greenply/ Century. Note: Sample as approved by GE.

Supply and fixing in repair 18mm thick HDHMR BOARD exterior grade including white coloured prelaminated sheet of required thickness over HDHMR board, anti fungal, moisture resistance, anti borer as per IS 14587 for frame and shutter for kitchen cabinets/ cupboards complete all as per specified and as directed by Engr-in-Charge. Make: Action Tessa/ Greenply/ Century. Note: Sample as approved by GE.

Supply and fixing 100mm Pull door handles, chrome finish, Stainless steel of SS 304 grade complete all as per specified and as directed by Engr-in-Charge. Note: Sample as approved by EIC/ GE.

Supply and fixing magnet door stopper of rectangular size for PVC cabinets including all fittings fixed complete all as specified and as directed.

Supply and fixing in repairs 22 to 25mm dia stainless steel curtain rod, fancy type/ decorative type, fixed to walls complete all as specified and as directed.

Supply and fixing in repairs, stainless steel decorative finials (round type with mirror optic finish trade/ standard pattern suitable for 22 to 25mm dia decorative/ fancy type curtain rods complete all as specified and as directed.

Supply and fixing in repairs brass chromium plated tubular towel rail, 20mm dia, D type, 60 cm long between flanges complete all as specified and as directed.

Supply and fixing in repairs, Cat. No. F5015131CH Towel Rack With Hook 24" 600mm Long with Lower Hangers, Stainless Steel complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

Supply and fixing rolled mild steel of grade Fe-290 (Grade E-165) in rolled section as in frames for doors/ windows, framing for cladding, glazing and the like fixed with angle cleats and connecting plates complete all as specified and as directed.

Supply and fixing mild steel of grade Fe-290 (Grade E-165) in framed work such as grills, grating with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders; ramed balusters; walk ways; railings; framework of water tanks and similar works complete all as specified and as directed.

Supply and fixing for preparation of new or previously untreated steel surfaces of any description, over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and as directed.

Supply and fixing for preparation of old painted wooden surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint complete all as specified and as directed.

Taking up or down steel tubing 15mm bore and connections including cleaning for refixing or removing from site complete all as specified and as directed.

Supply and fixing 20mm outer dia CPVC pipes SDR 11 and plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors complete all as specified and as directed.

Taking up or down steel tubing 20mm bore and connections including cleaning for refixing or removing from site complete all as specified and as directed.

Supply and laying 20mm bore tubes, galvanized steel, medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Taking up or down steel tubing 25mm bore and connections including cleaning for refixing or removing from site complete all as specified and as directed.

Supply and laying 25mm bore tubes, galvanized steel, medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Supply and fixing 32mm outer dia CPVC pipes SDR 11 and plain CPVC SDR 11 fittings on walls/ ceiling or laying in floors complete all as specified and as directed.

Dismantling of cast iron or reinforced concrete drain pipes of 100mm internal dia, jointed in cement mortar and taking out of trenches, if required complete all as specified and as directed.

Dismantling of cast iron or reinforced concrete drain pipes of 75mm internal dia, jointed in cement mortar and taking out of trenches, if required complete all as specified and as directed.

Supply and fixing 110mm bore UPVC (SWR) pipes type ‘B’, single socketed, in any length, with rubber ring joints fixed to walls complete all as specified and as directed.

Supply and fixing 110mm bore UPVC (SWR) pipes type ‘B’, single socketed, in any length, with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

Supply and fixing in repairs 110mm bore UPVC (SWR) bend, suitable for type ‘B’ pipes, any radius complete all as specified and as directed.

Supply and fixing in repairs 110mm bore UPVC (SWR) bend, suitable for type ‘B’ pipes, any radius with oval access door complete all as specified and as directed.

Supply and fixing 75mm bore UPVC (SWR) pipes type ‘B’, single socketed, in any length, with rubber ring joints fixed to walls complete all as specified and as directed.

Supply and fixing 75mm bore UPVC (SWR) pipes type ‘B’, single socketed, in any length, with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

Supply and fixing in repairs 75mm bore UPVC (SWR) bend, suitable for type ‘B’ pipes, any radius complete all as specified and as directed.

Supply and fixing in repairs 75mm bore UPVC (SWR) bend, suitable for type ‘B’ pipes, any radius with oval access door complete all as specified and as directed.

Supply and fixing in repairs for PVC (SWR) floor trap, suitable for type ‘B’ pipes, 75mm dia of outlet, plain with grating including jointing with solvent cement complete all as specified and as directed.

Supply and fixing in repairs 110mm bore UPVC (SWR) branch piece, suitable for type ‘B’ pipes, single (single Y) equal or unequal with oval access door complete all as specified and as directed.

Supply and fixing in repairs 75mm bore UPVC (SWR) branch piece, suitable for type ‘B’ pipes, single (single Y) equal or unequal with oval access door complete all as specified and as directed.

Supply and fixing stack clamps, for 110mm bore pipe, out of 50 x 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and as directed.

Supply and fixing stack clamps, for 75mm bore pipe, out of 50 x 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and as directed.

Supply and fixing in repairs 110mm bore UPVC (SWR) vent cowl, suitable for type ‘B’ pipes omplete all as specified and as directed.

Supply and fixing in repairs 75mm bore UPVC (SWR) vent cowl, suitable for type ‘B’ pipes complete all as specified and as directed.

Supply and fixing in repairs 15mm bore bib taps (long body), cast copper alloy, fancy type, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule as per Cat part No. CON-107KN of Make-Jaquar or techno commercially equivalent of any make complete all as specified and as directed.

Supply and fixing 15mm bore bib taps (long body), cast copper alloy, fancy type, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule as per Cat part No. CON-107KN of Make-Jaquar or techno commercially equivalent of any make complete all as specified and as directed.

Supply and fixing in repairs, two way angle valve fancy type chromium plated 15mm bore cast copper alloy with capstan heads, screwed down high pressure with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and as directed.

Supply and fixing in repairs 15mm bore stop valve/angle valve, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions omplete all as specified and as directed.

Supply and fixing in repairs 25mm dia gun metal, globe or gate valve, with iron wheel head, screwed both ends for iron pipe omplete all as specified and as directed.

Supply and fixing 25mm dia gun metal, globe or gate valve, with iron wheel head, screwed both ends for iron pipe omplete all as specified and as directed.

Dismantling water tanks of any description, exceeding 250 litres and not exceeding 500 litres capacity and removing from site complete all as specified and as directed.

Dismantling water tanks of any description, exceeding 500 litres and not exceeding 1000 litres capacity and removing from site complete all as specified and as directed.

Supply and fixing 1000 litres capacity rotational moulded polyethylene water storage tanks triple layer (cylindrical vertical with closed top), hoisted and fixed in position including 25mm dia tank Nipple/ Adaptor complete all as specified in SSR Part-I complete all as specified and as directed.

Supply and fixing 25mm bore ball brass valves, high pressure, with polythene float and fly-nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

Supply and fixing in soap dish/ shelf of PTMT fixed with and including chromium plated brass screws and wooden/ plastic cleats (Minimum weight 300 gms) complete all as specified and as directed.

Supply and fixing 32mm dia Bottle trap of PTMT having minimum water seal of 25mm. (Minimum weight 32mm - 260gms/ 40mm-270 gms) complete all as specified and as directed.

Supply and fixing in repairs Vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/ off white (closed pattern including all necessary accessories like rag bolts/ gel gasket (excluding flushing cistern and flush pipe) of size 655 x 350 x 735mm (Cat. No. S1031101) including plastic water closet seat, (Cat. No. B1520102) soft close seat cover, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete in all respect all as specified and as directed.

Supply and fixing in repairs for PVC low level flushing Cistern white with Twin flush fittings Cat. No. S1062128 10 liters capacity with all internal accessories and fixed to wall and making good to wall surfaces including taking down existing flushing cistern complete all as specified and as directed.

Supply and fixing in repairs vitreous china wash down water closet pan (pedestal pattern) white (excluding fixing bolt) including PVC valveless, syphonic action type, flushing cistern, low level, 10 litres capacity, white, with inlet, ball valve, float and handle including brackets and PVC flushing pipe, 32mm dia complete all as specified and as directed.

Supply only PVC flushing cistren low level, 10 liter capacity with syphonic action type ball valve including all fittings complete all as specified and as directed. Note :- Fixing of Flushing cistern included with fixing of WC as above.

Supply and fixing 110mm bore UPVC (SWR) WC connector with lip ring complete all as specified and as directed.

Supply and fixing 110mm bore UPVC (SWR) WC connector bent type complete all as specified and as directed.

Supply and fixing in repairs 110mm bore UPVC (SWR) junction, suitable for type ‘B’ pipes, single (single T) equal or unequal complete all as specified and as directed.

Supply and fixing 110mm bore UPVC (SWR) junction, suitable for type ‘B’ pipes, single (single T) equal or unequal complete all as specified and as directed.

Supply and fixing in repairs 75mm bore UPVC (SWR) junction, suitable for type ‘B’ pipes, single (single T) equal or unequal complete all as specified and as directed.

Supply and fixing in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed.

Supply and fixing in repairs vitreous china wash basin, white/ ivory, oval type, size 550 x 400mm including brackets, cutting for and pinning in ends of brackets or erecting stand, brass chromium plated perforated waste coupling/ fittings 32mm dia with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed and PVC waste pipe of 32mm bore and of suitable length complete all as specified and as directed. Note:- "If specified size not available in market, approx matching or next higher size as per direction of Engineer-in-Charge shall be fixed."

Supply and fixing vitreous china wash basin, white/ ivory, oval type, size 550 x 400mm including brackets, cutting for and pinning in ends of brackets or erecting stand, brass chromium plated perforated waste coupling/ fittings 32mm dia with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed and PVC waste pipe of 32mm bore and of suitable length complete all as specified and as directed. Note:- "If specified size not available in market, approx matching or next higher size as per direction of Engineer-in-Charge shall be fixed."

Supply and fixing in repair 15mm bore Pillar taps, cast copper alloy, with capston heads, chromium plated fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and as directed.

Supply and fixing 15mm bore Pillar taps, cast copper alloy, with capston heads, chromium plated fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and as directed.

Supply and fixing 15mm dia chromium plated, fancy type, sink cock with swivel neck complete all as specified and as directed.

Supply and fixing PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and as directed.

Supply and fixing in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever bracket, necessary chromium plated watse coupling, waste pipe and connecting union to pipe, overall size 510 x 430mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

Supply and fixing stainless steel plate rack, 0.50mm thick of standard pattern, of size 36" x 30" x 10" suitable for stacking 15 to 18 plates with hooks/ fittings complete all as specified and as directed. Note:- "If specified size not available in market, approx matching or next higher size as per direction of Engineer-in-Charge shall be fixed."

Material and labour for complete removal of loose/ cracked concrete including reinforcement if required, from RCC roof projection,chajja,fins,facia, roof bands and making good with RCC (1:1½:3) type A0 (nominal mix) (using 12.5mm graded stone aggregate) in RCC roof projection, chajja, fins,facia, roof bands and finished surface even and smooth without using extra cement including necessary form work and welding/ binding of reinforcement (including 0.9mm dia expanded metal wire mesh, for wrapping RCC members wherever required) if required completeas directed by the Engr-in-Charge. (Reiforcement will be measured and paid saperately under respective item).

Material and labour for precast reinforced cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) in landings, cover slabs (for manholes) chullah hoods, chajjas, shelves and similar articles with plain faces, set in CM 1:4, including necessary form work moulds complete all as specified and as directed. (Reinforcement shall be measured and paid for separately).

Material and labour for RCC 1:2:4 type B-1 (Nominal mix) (using 20mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies and in shelves and the like and chajjah including necessary form work complete all as specified and as directed.

Material and labour for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and as directed.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for (roof padding/ roof kerb/ sunken floor) including tarfelt, plaster and removing from site complete all as specified and as directed.

Material and labour for cement concrete 1:2:4 type B-0 mix (12.5mm graded stone aggregate) in padding over roof of any thickness complete all as specified and as directed.

Material and labour for brushing neat cement slurry with 3.00 kg of cement per sqm complete all as specified and as directed.

Material and labour for 15mm thick rendering in CM 1:3 over concrete surfaces (Roof) mixed with liquid water proofing compound @ 0.200 litre per bag of 50 kg of cement complete all as specified and as directed. Note:- Liquid water proofing compound shall be measured and paid for separately as “Supply only”.

Material and labour for water proofing treatment to roof slabs by applying one coat of bituminious/ polymerized primer confirming to IS-3384 @ 0.40 Ltrs/ Sqm, 3mm thick APP modified polymeric membrane of weight of 3 kg/ sqm with non-woven polyester reinforcement shall be laid over one coat of bitumen S-35 grade (30/40) applied @1.20Kg/ Sqm (minimum) with minimum 75mm side overlaps and minimum 100mm end overlaps, joints and overlaps shall be sealed and applying one coat of aluminium paint @ 0.11 Kg/ Sqm over APP membrane complete all as specified and as directed by Engr-in-Charge. Note: The primer and the membrane to be used shall be of the same manufacturer and to be applied by authorized applicator of OEM.

Material and labour for Supply and fixing Heat Resistant Terrace Tiles (300mm x 300mm x 10mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement and marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150mm height along the parapet walls in the same manner complete all as specified and as directed.

Supply only liquid water proofing compound complete all as specified and as directed.

Material and labour for 15mm thick rendering on floor and vertical side of sunken floor of stone masonry surfaces/ brick work/ concrete surfaces in CM (1:3) mixed with liquid water proofing compound @ 0.200 litre per bag of 50 kg of cement and finished even and smooth without using extra cement complete all as specified and as directed. Note:- Liquid water proofing compound shall be measured and paid for separately as “Supply only”.

Material and labour for applying roof/ sunken treatment on sunken floor with APP modified membrane (minium 3mm thick) weight not less than 3 kg/ sqm and reinforced with non-woven polyester reinforcement/ mat (centre core) with thermal insulation with polythene finish on upper side of membrane, laid by torch application method with overlaps 150mm on length side and 100mm on the width side as per manufacturer's instructions over and including one coat of approved cold applied bituminous oil based primer (IS-3384) @ 250 gm/ sqm complete all as specified and as directed by Engineer-in-Charge.

Material and labour for cement concrete (1:5:10) type E-2 (using 40mm graded stone aggregates) as in foundation, filling and mass concrete/ sunken floors complete all as specified and as directed.

Material and labour for 25mm thick PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) in sub floors mixed with liquid water proofing compound @ 0.200 litre per bag of 50 kg of cement. Note:- Liquid water proofing compound shall be measured and paid for separately as “Supply only”.

Supply and fixing floor door stopper, with 150mm long cover plate, of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor complete all as specified and as directed.

Material and labour double action floor spring, hydraulically regulated, made up of minimum 1.25mm thick aluminium alloy sheet, foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and as directed.

Material and labour in repairs for PVC (SWR) gully trap 125/ 110mm, setting and jointing with solvent cement complete all as specified and as directed.

Material and labour for 75mm thick PCC 1:3:6 mix type C2 as in plinth protection and paving finishing cone surface even and smooth without using extra cement complete all as specified and as directed.

Material and labour treatment of surface under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and as directed.

Material and labour for treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and as directed.

Supply and fixing of stainless steel W Hinges SS 202 Grade steel Rust Resistance, for fixing cup boords shutters sizes of hinges 3" to 4" and 1.5mm thickness, suitable for 18mm thick cabinets shutters complete all as specified and as directed.

Material and labour for sand filling under floors or in foundations, laid in layers not exceeding 15 cm thick, spread levelled including watering and consolidation complete all as specified and as directed.

Material and labour for Hard core gauge not exceeding 63mm of broken bricks diposited spread and levelled in layers not exceeding 15 cm watered and rammed to a true surface complete all as specified and as directed.

Material and labour for 75mm thick plain cement concrete (1:4:8) type D-2, (using 40mm graded stone aggregate) as in sub base complete all as specified and as directed.

Material and labour for Machine pressed, precast plain cement concrete Interlocking paver block, factory made (with grey cement and pigment) conforming to IS-15658-2006, 80mm thickness laid over sand cushioning layer and joints filled with sand in hardstanding, fabricated with M-40 grade concrete, complete all as specified and as directed. Note:- "Shade, shape and pattern of inerlocking blocks shall be approved by Engineer-in-Charge/ GE."

Dismantling ceiling and wall boards or insulation board any thickness including cover fillets complete all as specified and as directed.

Material and labour for 10mm thick plaster of paris ceiling (Gypsum anhydrous) to flat surface over 2nd class soft wood fillets, or metal frame work and reinforced with galvanised iron wire mesh with 2mm dia galvanised iron wire to hanging and size of grid 605 x 605mm galvanised iron frame work for seamless ceiling comprising of galvanised iron perimeter channnel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with galvanised iron cleat and steel expansion fasteners with and including ceiling section (not exceeding 1.2 meter length) of 0.55 m thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre and applying two coats of distemper oil emulsion over 1 of 2mm thick putty over one coat of primer complete all as specified and as directed.

Supply and fixing 10mm thick PVC insulation panels with EPS stuck to 1mm printed PVC sheet suitably placed in false ceiling grid made of Aluminium/ Galvanised Iron/ Mild Steel as per specification complete all as specified and as directed.

Supply and fixing of Galvanised Iron frame work for seamless ceiling comprising of Galvanised Iron perimeter channnel 0.55mm thick with two unequal flanges of 20 and 30mm and web of 27mm fixed to surrounding wall using nylon sleeves and screws at 450mm centre to centre/ intermediate channel 0.9mm thick having two equal flanges of 15mm each and web of 45mm suspended from soffit at approx 900mm centre to centre with Galvanised Iron cleat and steel expansion fasteners with and including ceiling section (not exceeding 1.2 meter length) of 0.55mm thickness having kurled web of 50mm and flange of 26mm each with lips of 10.5mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457mm centre to centre complete all as specified and as directed.

Supply and fixing of solid PVC Wall Lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications complete all as specified and as directed.

Supply and fixing of 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing complete all as specified and as directed.

Supply and fixing horizontal rolling blinds for windows including roller complete as per manufacturers instruction complete all as specified and as directed. Note: Rolling blind pattern and colour shall be as directed by Engineer-in-Charge.

Supply and fixing in repairs Vitreous China Urinal, Half stall type, 420 x 395 x 635mm white (excluding flushing cistern, flush pipe) white (minimum), with grating and union for discharge pipe including chromium plated waste coupling, CP spreader and necessary waste pipe complete all as specified and as directed by Engineer-in-Charge.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed.

Supply and fixing ACP sheet of 3mm thk for parking or similar shed including necessary aluminium pipe framing complete as per manufacturers instruction. (Note: ACP sheet pattern and colour shall be as directed by Engineer-in-charge)

Taking down carefully existing unserviceable copper/ aluminium point wiring (light, fan, socket or power point) complete with fittings/ fixures such as switches sockets, ceiling rose, fan regulators (except tube light fittings), removing materials for taking credit and making good disturbed surface of wall, floors complete all as specified and as directed by Eng-in-Charge.

Material and labour for point wiring complete with 1.5 sqmm single core PVC insulated (FRLS) and unsheathed cable 1100 volts grade with multistranded copper conductor drawn through and including PVC Conduit medium grade not less than 20mm dia and all accessories concealed in walls/ roofs/ floors/ ceiling and including provision of 1.5 sqmm copper cable as earth continuity conductor and connected to common earth dolly, in modular sunken boxes in wall with modular plate cover for housing the switches, socket outlets, fan regulators complete including cutting of chases where as required and making good all disturbed work to match the existing complete all as specified and as directed for the following:-

(a) One light point controlled by one switch.

(b) One ceiling fan point controlled by one switch and fan regulator.

(c) One exhaust fan point controlled by one switch

(d) One 3 pin socket outlet 5 Amps independent board.

(e) One 3 pin socket outlet 5 Amps on the same board with other switch.

(f) One bell point controlled by one bell push

(g) One light point controlled by two 2 - way switches.

All as per item No 158.04 here-in-before but with 2.5 sqmm PVC insulated multistranded flexible unsheathed copper conductor inclusive of 2.5 sqmm PVC insulated multistranded flexible copper conductor for one independent 6 pin 16 Amp socket complete all as specified and as directed.

Supply and fixing for Modular type switch 1 way 6A, 1 module, 230 V, AC 50Hz ISI Marked with valid CML No. complete all as specified and as directed.

Supply and fixing for Modular type switch 2 way 6A, 1 module, 230 V, AC 50Hz ISI Marked with valid CML No. complete all as specified and as directed.

Supply and fixing for Modular type switch 1 way 20A, 1module, 230 V, AC 50Hz ISI Marked with valid CML No. complete all as specified and as directed.

Supply and fixing for Modular type socket outlet multipurpose having provision for Socket, 6A - 2/3 pin combined 2 module, 230 V, AC 50Hz ISI Marked with valid CML No. complete all as specified and as directed.

Supply and fixing for Modular type socket outlet multipurpose having provision for 3 pin 16A and 3 pin 6A, 2 module, 230 V, AC 50Hz ISI Marked with valid CML No. complete all as specified and as directed.

Supply and fixing for Modular type Fan step regulator electronic type, 230V,120W - 2 module ISI marked with suitable CML No and connecting upto complete all as specified and as directed.

Supply and fixing for Modular type Bell push 6A, 1 module ISI marked with suitable CML No and connecting upto complete all as specified and as directed.

Supply and fixing ceiling rose surface polycarbonate body three terminal complete all as specified and as directed.

Supply and fixing of ceiling fan complete with blades, down rod from existing roof/ truss to fall ceiling and accessories, 230V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE, five star rated with brushless direct current motor including ceiling fan connecting up with three core flexible copper conductor cable of suitable size from ceiling rose and taking down existing UNSV ceiling fan complete all as specified and as directed. Note:- 1. Old ceiling fans shall be deposited to AGE E/M store yard for re issue to other buildings after repair/ servicing or suryed off as per procedure in vogue.

Supply and fix of exhaust fan steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers, voltage 230V, 50Hz, RPM 1200, copper winding complete including exhaust fan connecting up with three core flexible copper conductor cable of suitable size from ceiling rose and taking down existing UNSV exhaust fan complete all as specified and as directed. Note : 1. Old unserviceable Exhaust fans shall be deposited to AGE E/M store yard for re issue to other buildings after repair/ servicing or suryed off as per procedure in vogue.

Supply and fix of exhaust fan steel body AC single Phase. 230V of size 450mm sweep with, blades, and frame and louvers, voltage 230V, 50Hz, RPM 1200, copper winding complete including exhaust fan connecting up with three core flexible copper conductor cable of suitable size from ceiling rose and taking down existing UNSV exhaust fan complete all as specified and as directed. Note:- 1. Old unserviceable Exhaust fans shall be deposited to AGE E/M store yard for re issue to other buildings after repair/ servicing or suryed off as per procedure in vogue.

Supply and fixing of LED ceiling light fitting of size 600mm X 600mm, 36 Watt, 220 Volt AC recessed type with high efficiency PMMA diffuser with soft glare free light complete with drivers, holders and LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cable of suitable size complete including taking down old unserviceable existing light fitting complete all as specified and as directed. Note:- (Warm Light/ Neutral Light) color temperature 6500-3800K as per site requirement as directed and approved by Engr-in-Charge.

Supply and fix of LED light fitting 1 X 20 Watt, 220 Volt AC decorative box type with drivers, holders and including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete including taking down old unserviceable existing light fitting complete all as specified and as directed. Note:- (Warm Light/ Neutral Light) color temperature 6500-3800K as per site requirement as directed and approved by Engr-in-Charge.

Supply and fix of LED batten tube light fitting of capacity 10 Watt, 2' long a indoor decorative LED engineering plastic batten with opal diffuser, IP20 protection complete all as specified and as directed. Note:- (Warm Light/ Neutral Light) color temperature 6500-3800K as per site requirement as directed and approved by Engr-in-Charge.

Supply and fix of Lamp holder, PVC/ Polycarbonate type with back plate suitable for batten fittings inclouding one LED lamp 7 Watt complete all as specified and as directed

Supply and fixing Ding Dong call bell AC, 230 Volt, single Pole complete all as specified and as directed.

Material and labour for Sub main wiring with FRLS two run of single core PVC insulated and unsheathed fire retardant multi stranded copper conductor cable 1100 volt grade IS-694, marked of 1.5 Sqmm size drawn through in PVC conduit medium grade ISI marked and conduit junction boxes, terminal boxes and accessories such as tees, bends, elbows, reducers, bell mouth tube ends concealed in walls/ roofs/ floors/ ceiling including one run of 1.5 sqmm PVC insulated and unsheathed FRLS multi stranded copper conductor cable for earth wire continuity conductor complete including cutting of chases where as required and making good all disturbed work to match the existing complete all as specified and as directed. Note:- Two runs of single core 1.5 sqmm and one run of 1.5 sqmm copper FRLS cable as earth continuity conductor and suitable size conduit with accessories shall be measured as one length.

Material and labour for Sub main wiring with FRLS two run of single core PVC insulated and unsheathed fire retardant multi stranded copper conductor cable 1100 volt grade IS-694, marked of 4.0 Sqmm size drawn through in PVC conduit medium grade ISI marked and conduit junction boxes, terminal boxes and accessories such as tees, bends, elbows, reducers, bell mouth tube ends concealed in walls/ roofs/ floors/ ceiling including one run of 4.0 sqmm PVC insulated and unsheathed FRLS multi stranded copper conductor cable for earth wire continuity conductor complete including cutting of chases where as required and making good all disturbed work to match the existing complete all as specified and as directed. Note : Two runs of single core 4.0 sqmm and one run of 4.0 sqmm copper FRLS cable as earth continuity conductor and suitable size conduit with accessories shall be measured as one length.

Material and labour for Sub main wiring with FRLS two run of single core PVC insulated and unsheathed fire retardant multi stranded copper conductor cable 1100 volt grade IS-694, marked of 6.0 Sqmm size drawn through in PVC conduit medium grade ISI marked and conduit junction boxes, terminal boxes and accessories such as tees, bends, elbows, reducers, bell mouth tube ends concealed in walls/ roofs/ floors/ ceiling including one run of 6.0 sqmm PVC insulated and unsheathed FRLS multi stranded copper conductor cable for earth wire continuity conductor complete including cutting of chases where as required and making good all disturbed work to match the existing complete all as specified and as directed. Note: Two runs of single core 6.0 sqmm and one run of 6.0 sqmm copper FRLS cable as earth continuity conductor and suitable size conduit with accessories shall be measured as one length.

Material and labour for Sub main wiring with FRLS two run of single core PVC insulated and unsheathed fire retardant multi stranded copper conductor cable 1100 volt grade IS-694, marked of 10.0 Sqmm size drawn through in PVC conduit medium grade ISI marked and conduit junction boxes, terminal boxes and accessories such as tees, bends, elbows, reducers, bell mouth tube ends concealed in walls/ roofs/ floors/ ceiling including one run of 10.0 sqmm PVC insulated and unsheathed FRLS multi stranded copper conductor cable for earth wire continuity conductor complete including cutting of chases where as required and making good all disturbed work to match the existing complete all as specified and as directed. Note : Two runs of single core 10.0 sqmm and one run of 10.0 sqmm copper FRLS cable as earth continuity conductor and suitable size conduit with accessories shall be measured as one length.

Material and labour for Sub main wiring with FRLS four run of single core PVC insulated and unsheathed fire retardant multi stranded copper conductor cable 1100 volt grade IS-694, marked of 16.0 Sqmm size drawn through in PVC conduit medium grade ISI marked and conduit junction boxes, terminal boxes and accessories such as tees, bends, elbows, reducers, bell mouth tube ends concealed in walls/ roofs/ floors/ ceiling including two run of 16.0 sqmm PVC insulated and unsheathed FRLS multi stranded copper conductor cable for earth wire continuity conductor complete including cutting of chases where as required and making good all disturbed work to match the existing complete all as specified and as directed. Note:- Four runs of single core 16.0 sqmm and two run of 16.0 sqmm copper FRLS cable as earth continuity conductor and suitable size conduit with accessories shall be measured as one length.

Supply and fixing for sheet metal enclosures distribution board double door,TPN vertical 8 way suitable for fixing of Four pole MCCB as in commer and MCBs SP as out going and duly fitted with Bus bar, Neutral link, blanking plates complete. The DB shall be included with one No MCCB, 4 pole, 415/ 430 Volt, 160 Amps, fixed megnatic and thermal release, having rupturing capacity 36KA on 415 V icu. Make of DB L&T and Make of MCCB L&T Encloser & MCCB shall preferably of same make fixed on wall complete with all acessories including taking down old unserviceable MCB DB with MCBs complete all as specified and as directed. (MCB s required for out going shall be measured and paid separately).

Supply and fixing of sheet metal enclosures (double door) for DBs where MCBs to be used single pole and neutral 8 way 240 V with 200 amps rated bus bar fixed on wall complete with all acessories including taking down old unserviceable MCB DB with MCBs complete all as specified and as directed.

Supply and fixing including connecting MCB single pole, having rupturing 10KA, 6 amps to 32 amps as ordered 240 Volts complete all as specified and as directed.

Supply and fixing of MCB Single pole and neutral (DP), having rupturing 10KA, 240V 63 amps as ordered complete all as specified and as directed.

Supply and fixing Modular Power unit 25 Amp unit including suitable size of sunken metal box and white cover plate including Modular Miniature Case Circuit Breaker and plug top with indicator of capacity 25 Amp complete all as specified and as directed by Engr-in-Charge.

Supply and fixing wall mounted fan energy efficient 300mm plastic body sweep with pull cord 240 AC, 50 Hz, single phase with all accesseries complete all as specified and as directed.

Supply and fixing Rigid non-metallic PVC conduit exclusive of boxes (junction/ terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks concealed in walls/ roofs/ floors/ ceiling of size 20mm dia including cutting of chases where as required and making good all disturbed work to match the existing all as specified and as directed.

Supply and fixing Rigid non-metallic PVC conduit exclusive of boxes (junction/ terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks concealed in walls/ roofs/ floors/ ceiling of size 32mm dia including cutting of chases where as required and making good all disturbed work to match the existing complete all as specified and as directed.

Supply and fixing wall mounted Galvanised Iron cable tray not less than 2mm thick of Size 40 X 300mm tray for support of LT/ LAN cable perforated bottom design allow for hold down attachment, cable attachements and heat dissipation complete all as specified and as directed. Note:- Coated rate shall be deemed all fixing and jointing accessories like screw, washers, nuts and bolts.

Supply and fixing of engagement light wall mounting B22 type holders including red and green LED lamps complete all as specified and as directed. Note:- Coated rate shall be deemed all fixing and jointing accessories like screw, washers, nuts and bolts.

Supply and install hi wall split units indoor/ outdoor complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality with minimum 5 star rating invertor type and EER 3.2 of capacity 1.5 TR complete all as specified and as directed. Note:- The split AC shall carry minimum 5 star rating as per Bureau of energy Efficiency (BEE) labelling programme.

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type and designed for input variation between 170V to 250V with output voltage stabilized at 230V with accuracy of ± 2.5% and of capacity 04 KVA complete all as specified and as directed.

(o) Frequency meter digital type- 01 No. (p) Earthing terminals- 2 Nos (q) Digital Manual and AMF control panel: Digital Manual is equipped with 16 bit hogh spedd RISC processor based controller. Power contactor Cap 320 Amp - 02 Nos and MCCB 4 Pole adjustable type Cap 320 Amp, 36 KA - 02 Nos. It display the following parameters Safty System with special sensors to safe guard the engine aginst faults, like low lub oil pressure, high coolant temperature, battery over/ under/ weak volt, fail to crank/ start, sensor failure, over spedd, low fuel level with alarm. (r) AC Alternator protection Over/ Under Voltage, Over/ Under Frequency. (s) Present system with push button'. (t) DC Voltmeter- 01 no (u) Mechanical Governior. (v) Reverse power relay & reverse reactive power relays. (w) Netural switching facility. (x) SMOS suitable for charging 12 volts with trickle and boost facility- 01 No (y) Independent earthing terminals for engine & alternator- 02 each. (z) Battery charging alternator 12 volt (aa) Material and labour for making PCC Foundation (1:3:6) type B1 (using 20mm graded rendering in CM (1:6) surface even and smooth Flooring PCC(1:3:6) type B1 (using 20mm graded stone aggregate) 100mm thick hard core over rammed earth for 100 KVA DG Set complete all as specified and as directed.

Earthing complete with galvanised steel earth plate electrode 60 x 60 cm x 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron strip 320 x 06mm as earth lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion complete all as specified and as directed.

City Light (BID ID -3130795)

Shree Vaishno Enterprises (BID ID -3130832)

Saroj Construction Company (BID ID -3112895)