Tender for the Work of Supply, Laying, and Testing & Commissioning Of 11KV underground XLPE Cable (Cable to be supply by DGVCL) with Cable End Termination and Straight joint kit (to be supplied by the Contractor / Agency) and HDPE green Pipe for HT Underground Cable Work and Erection of HT-LT lines & T/C etc. for (Umargam AG) For Wire free City mission within Jurisdiction of Solsumba Sub division Under Vapi Ind. Division.

(A) CAPITAL WORK LABOUR RATES FOR FY 2024-25 (WITHOUT GST)

Description Rate

HT TAPPING FROM THE EXISTING POLE INCLUDING FIXING OF CROSS ARMS, CLAMPS ANTI-CLIMBING

DEVICES, DANGER BOARD, INSULATORS ETC. COMPLETE AND PAINTING OF FABRICATED MATERIALS

AND NUMBERING COMPLETE WITH COST PAINTS AS PER STANDARD SPECIFICATION BUT EXCLUDING

ERECTION OF GUY SET AND EARTHING.

ERECTION OF PSC POLES OF 8METER 200 KG INCLUDING EXCAVATION OF PIT AND REFILLING OF

EARTH, FIXING OFCROSS ARMS, TOP FITTING CLAMPS ANTICLIMBING DEVICES, INSULATORS

ETC.COMPLETE AND PAINTING OF FABRICATED MATERIALS USED ON THE POLES AND NUMBERING

WITH COST OF PAINT AS PER STANDARD SPECIFICATION BUT EXCLUDING

ERECTION OF GUY SET AND EARTHING.

ERECTION OF STEEL POLES OF 9 TO 11 METERS INCLUDING EXCAVATION OF PIT AND REFILLING OF

EARTH, FIXING OF CROSS ARMS, TOP FITTING CLAMPS ANTI-CLIMBING DEVICES, DANGER BOARD,

INSULATORS ETC. COMPLETE AND PAINTING OF STEEL POLE, FABRICATED MATERIALS USED ON THE

POLE AND NUMBERING WITH COST OF PAINT AS PER STANDARD SPECIFICATION BUT EXCLUDING

ERECTION OF GUY SET AND EARTHING.

ERECTION OF STEEL POLE OF 13 METERS FOR RAILWAY CROSSING ON BG/MG/NG LINE FOR

0.400/11/22KV OVERHEAD LINES I.E INCLUDING EXCAVATION OF PIT & REFILLING OF EARTH, FIXING

CROSS ARMS, TOP FITTING CLAMPS,ANTICLIMBING DEVICES DANGER BOARD, INSULATORS ETC.

COMPLETE AND PAINTING OF STEEL POLES, FABRICATED MATERIALS USED ON THE POLES

ANDNUMBERING WITH COSTOF PAINT AS PER STANDARD SPECIFICATION BUT EXCLUDING ERECTION

OF GUY SETS AND EARTHING.

ERECTION OF DOUBLE POLE STRUCTURE OF 8 METERS 200 KG PSC POLES INCLUDING EXCAVATION

OF PITS & REFILLING OF EARTHING, FIXING OF CHANNELS, SUPPORTING ANGLES,CLAMPS, ANTI-

CLIMBING DEVICES DANGERBOARDS,INSULATORS ETC.COMPLETE AND PAINTING OF FABRICATED

MATERIALS USED ON THE POLES AND NUMBERING WITH COST OF PAINT AS PER STANDARD

SPECIFICATION BUT EXCLUDING ERECTION OF GUY SETS AND EARTHING. (WITHOUT AB SWITCH)

ERECTION OF DOUBLE POLE STRUCTURE OF 9 TO 11 METERS.STEEL POLE INCLUDING EXCAVATION

OF PITS &REFILLING OF EARTH, FIXING OF CHANNELS, SUPPORTING ANGLES,CLAMPS,ANTI-CLIMBING

DEVICES DANGER BOARDS, INSULATORS ETC.COMPLETE &PAINTING POLES,FABRICATED MATERIAL

SUSED ON THE POLES AND NUMBERING WITH COST OF PAINTSAS PER STANDARD SPECIFICATION

BUT EXCLUDING ERECTION OF GUY SET ANDEARTHING. (WITHOUT AB SWITCH)

ERECTION OF DOUBLE POLE STRUCTURE WITH MOUNTING OF AB SWITCH, HGFUSES OF 8 MTRS 200

KG PSC POLES INCLUDING EXCAVATION OF PITS AND REFILLING OF EARTH,FIXING OF CHANNELS

SUPPORTING ANGLES, CLAMPS,ANTI-CLIMBING DEVICES, DANGER BOARDS, INSULATORS,DO FUSES

ETC. COMPLETE AND PAINTING OF FABRICATED MATERIALS USED ON THE POLES AND NUMBERING

WITH COST OF PAINT AS PER STANDARD SPECIFICATION BUT EXCLUDING OF ERECTION

OF GUY SET AND EARTHING. (WITH AB SWITCH)

ERECTION OF DOUBLE POLE STRUCTURE WITH MOUNTING OF AB SWITCH,HG FUSES, 9 TO 11

METERS STEEL POLES INCLUDING EXCAVATION OF PITS AND REFILLING OF EARTH, FIXING OF

CHANNEL, SUPPORTING ANGLES, CLAMPS, ANTICLIMBING DEVICES , DANGER BOARDS, INSULATORS,

ETC. COMPLETE AND PAINTING OF POLES FABRICATED MATERIALS USED ON THE POLES

ANDNUMBERING WITH COST OF PAINT AS PER STANDARD SPECIFICATION

BUTEXCLUDING ERECTION OF GUY SET AND EARTHING. (WITH AB SWITCH)

ERECTION OF DOUBLE POLE STRUCTURES WITH MOUNTING OFAB SWITCH,FUSES, TRANSFORMERS,

LIGHTENING ARRESTORS, DISTRIBUTION BOX. OF 8 METERS 200 KG PSC POLES INCLUDING

EXCAVATION OF PITS AND REFILLING OF EARTH, CARTING OF TRANSFORMERS FROM STORES TO

SITE, FIXING OF CHANNELS, SUPPORTING ANGLES,BRACINGS CROSS ARMS CLAMPS,

ANTICLIMBING DEVICES DANGER BOARDS,CONDUCTOR AND CABLE WIRING ETC.COMPLETE AND

PAINTING OF FABRICATED MATERIALS USED ON THE POLES AND NUMBERING WITH COST OF PAINT

AS PER STANDARD SPECIFICATION BUT EXCLUDING ERECTION OF GUY SETS AND EARTHING.

File No: DGVCLDVPI/tender/e-file/4448/2026/2647/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI

Letter No: DGVCLDVPI/0529/08/2026 Approved Date: 18-08-2026 07:18

ERECTION OF DOUBLE POLE STRUCTURE WITH MOUNTING OF AB SWITCH,HG FUSES

TRANSFORMERS, LIGHTENING ARRESTORS, DISTRIBUTION BOX 9 TO 11 METERS STEEL POLES

INCLUDINGEXCAVATION OF PITS & REFILLING OF EARTH CARTING OF TRANSFORMERS FROM STORE

TO SITE, FIXINGOF CHANNELS SUPPORTING ANGLES, BRACING, CROSS ARMS,CLAMPS,

ANTICLIMBING DEVICES, DANGER BOARDS,CONDUCTOR AND CABLE WIRING ETC. COMPLETE AND

PAINTING OF POLES FABRICATED MATERIALS USED ON THE POLES AND NUMBERING AS PER

STANDARD SPECIFICATION BUT EXCLUDING ERECTIONS OF GUY SETS AND EARTHING.

ERECTION OF GUY SET INCLUDING EXCAVATION OF PITS & REFILLING OF EARTH AS PER STANDARD

SPECIFICATION WITH STAY CLAMPS, STAY WIRE, ANCHOR ROD, TURN BUCKLE, EYEBOLT, GUY

INSULATOR, CEMENT CONCRETE BLOCK ETC. BUT EXCLUDING CONCRETING.

CONCRETING OF POLES, GUYS, ETC. INCLUDING COST OF CEMENT SAND METAL (1:2:4)AND WATER

ETC. AS PER STANDARD SPECIFICATION.

ERECTION OF COIL TYPE EARTHING INCLUDING COST OF COAL,SALT ETC. BUT WITHOUT COST OF Gl

WIRE AS PER STANDARD SPECIFICATION(20kg salt+20kg coal)

ERECTION OF Gl PIPE/CI PLATE TYPE EARTHING INCLUDINGCOST OF COAL SALT ETC. BUT

WITHOUT COST OF PIPE/GIPLATE Gl WIRE AS PER STANDARDSPECIFICATION. (20k solt+20k coal)

ERECTION OF STREET LIGHT FIXTURE COMPLETE WITH CLAMPS, BRASS NIPPLE, BRASS

HOLDER TECK WOODBUSH,REFLECTORS FUSE, WIRING ETC. AS PER STANDARD SPECIFICATION

BUT EXCLUDING COST OF MATERIALS.

STRINGING OF ALL TYPE OF CONDUCTOR (EXCEPT DOG CONDUCTOR) FOR 11/22KV & LT LINES

INCLUDING FIXING OF INSULATORS BINDING JUMPERING ETC.

STRINGING OF Gl WIRE 8 SWG INCLUDING BINDING JUMPERING ETC.

PROVIDING SINGLE PHASE SERVICE CONNECTION WITH- PVC 4MM TWIN CORECABLE FROM

TERMINAL POLE TOMETERING POINT INCLUDING FIXING OFMETER WITH METER EARTHING

COMPLETE WORK AS PER STANDARD SPECIFICATION BUT EXCLUDING COST OF MATERIALS.

PROVIDING THREE PHASE 4 WIRE SERVICE CONNECTION WITH PVC 4MM2/10MM2 FOUR CORE CABLE

FROM TERMINAL POLE TO METERING POINT INCLUDING FIXING OF METER WITH METER EARTHING

COMPLETE WORK AS PER STANDARD SPECIFICATION BUT EXCLUDING COST OF MATERIALS.

ADDITIONAL COST FOR EXCAVATION OF PIT IN HARD ROCK AREA FOR ERECTION OF POLE/ GUY ETC.

AS PER STANDARD SPECIFICATION OVER & ABOVE NORMAL COST COVERED AGAINST EXCAVATION

OF PIT UNDER NORMAL SOIL FOR ERECTION OF POLE,GUY, DOUBLE POLE STRUCTURE EARTHING

WITH THE APPROVAL OF SUPDT.ENGINEER.

PROVIDING GUARDING TO HT LINE ON ROAD/ RAIL CROSSING.

PROVIDING GUARDING OF LT LINES ON ROAD/RAIL CROSSING.

LT LINE TAPPING- SINGLE PHASE

LT LINE TAPPING- THREE PHASE

LAYING OF OVER HEAD LT CABLE FOR ROAD CROSSING,HT LINE CROSSING AND TELEPHONE LINE

CROSSING ETC.(PER SPAN)

ERECTION OF SINGLE POLE STRUCTURESWITH, HG FUSES,TRANSFORMERS,LIGHTENING

ARRESTOR, DISTRIBUTION BOX. ON 8 METERS 200 KG PSC POLE INCLUDING EXCAVATION OF PITS

AND REFILLING OF EARTH, CARTING OF TRANSFORMERS FROM STORES TO SITE, FIXING OF

CHANNELS, SUPPORTING ANGLES,BRACINGS CROSS ARMS CLAMPS, ANTICLIMBING DEVICES

DANGER BOARDS,CONDUCTOR AND CABLE WIRING ETC.COMPLETE AND PAINTING OF FABRICATED

MATERIALS USED ON THE POLE AND NUMBERING WITH COST OF PAINT AS PER STANDARD

SPECIFICATION BUT EXCLUDING ERECTION OF GUY SETS AND EARTHING.

ERECTION OF SINGLÉ POLE STRUCTURES WITH HG

FUSES,TRANSFORMERS,LIGHTENING ARRESTOR, DISTRIBUTION BOX. ON 9 to 11 METERS RSJ POLE

INCLUDING EXCAVATION OF PITS AND REFILLING OF EARTH, CARTING OF TRANSFORMERS FROM

STORES TO SITE, FIXING OF CHANNELS, SUPPORTING ANGLES,BRACINGS CROSS ARMS CLAMPS,

ANTICLIMBING DEVICES DANGER BOARDS,CONDUCTOR AND CABLE WIRING ETC.COMPLETE AND

PAINTING OF FABRICATED MATERIALS USED ON THE POLE AND NUMBERING WITH COST OF PAINT AS

PER STANDARD SPECIFICATION BUT EXCLUDING ERECTION OFGUY SETS AND EARTHING.

ERECTION OF PSC POLES OF IO METER 270 KG INCLUDING EXCAVATION OF PIT AND REFILLING OF

EARTH, FIXING OF CROSS ARMS, TOP FIITING CLAMPS ANTICLIMBING DEVICES, INSULATORS ETC.

COMPLETE AND PAINTING OF FABRICATED MATERIALS USED ON THE POLES AND NUMBERING WITH

COST OF PAINT AS PER STANDARD SPECIFICATION BUT EXCLUDING ERECTION OF GUY SET AND

File No: DGVCLDVPI/tender/e-file/4448/2026/2647/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI

Letter No: DGVCLDVPI/0529/08/2026 Approved Date: 18-08-2026 07:18

ERECTION OF DOUBLE POLE STRUCTURE OF 10 METER 270 KG PSC POLES INCLUDING EXCAVATION

OF PITS & REFILLING OF EARTHING, FIXING OF CHANNELS, SUPPORTING ANGLES,CLAMPS, ANTI-

CLIMBING DEVICES DANGERBOARDS,INSULATORS ETC.COMPLETE AND PAINTING OF

FABRICATED MATERIALS USED ON THE POLES AND NUMBERING WITH COST OF PAINT AS PER

STANDARDSPECIFICATION BUT EXCLUDING ERECTION OF GUY SETS ANDEARTHING. WITHOUT AB

STRINGING OF IOOMM2 ACSR/100MM2 AAAC CONDUCTOR FOR HT/ LT LINES INCLUDING FIXING OF

INSULATORS, BINDING JUMPERING ETC.

STRINGING OF DOG CONDUCTOR FOR 11/22KV HT LINES INCLUDING FIXING OF INSULATORS,

BINDING JUMPERING ETC.

ERECTION OF DOUBLE POLE STRUCTURES WITH MOUNTING OF AB SWITCH,HG FUSES,

TRANSFORMERS, LIGHTENING ARRESTORS, DISTRIBUTION BOX. OF 10 METERS 270 KG PSC POLES

INCLUDING EXCAVATION OF PITS AND REFILLING OF EARTH, CARTING OF TRANSFORMERS FROM

STORES TO SITE, FIXING OF CHANNELS, SUPPORTING ANGLES,BRACINGS CROSS ARMS CLAMPS,

ANTI-CLIMBING DEVICES,DANGER BOARDS, CONDUCTOR AND CABLE WIRING ETC.COMPLETE AND

PAINTING OF FABRICATED MATERIALS USED ON THE POLES AND NUMBERING WITH COST OF PAINT

AS PER STANDARD SPECIFICATION BUT EXCLUDING ERECTION OF GUY SETS AND EARTHING.

DISMENTALLING OF 8 MTR PSC POLE WITH CREDITING OF FABRICATION AT STORE &STACKING OF

POLE SAFELY ON ROAD SIDE OR CREDITING TO DEPARTMENTAL STORE

DISMENTALLING OF 10 MTR PSC POLE WITH CREDITING OF FABRICATION AT STORE & STACKING OF

POLE SAFELY ON ROAD SIDE OR CREDITING TO DEPARTMENTAL STORE

DISMENTALLING OF TRANSFORMER CENTRE (8 MTR PSC POLE) (WITH TRANSFORMER) WITH

CREDITING OF FABRICATION & TRANSFORMER AT STORE & STACKING OF POLE SAFELY ON

ROADSIDE OR CREDITING TO DEPARTMENTAL STORE

DISMENTALLING OF TRANSFORMER CENTRE (8 MTR PSC POLE) (WITHOUT TRANSFORMER) WITH

CREDITING OF FABRICATION AT STORE & STACKING OFPOLE SAFELY ON ROAD SIDE ORCREDITING

TO DEPARTMENTAL STORE

STRINGING OF LT ABC OF 1*35 SQ MM + 1*25 SQ MM INCLUDING FIITING OF ALL ACESSORIES I.E.

SPECIAL DESIGN SUSPENSION / TENSION CLAMP, FIXING OF CROSS ARM, LT SHACKLE INSULATOR

ETC. FOR FIXING OF MESSENGER WIRE AND TO PROVIDE SERVICE CONNECTION ON AERIAL BUNCH

CABLE BY INSULATED PIERCE-ING CONNECTORS THROUGH SERVICE CONNECTION BOX COMPLETE

AS REQUIRED & DIRECTED BY ENGINEER IN CHARGE.

STRINGING OF LT ABC OF 3*50 SQ MM +1*25 SQ MM+1*35 SQ MM INCLUDING FITTING OF ALL

ACESSARIES I.E. SPECIAL DESIGN SUSPENSION / TENSION CLAMP, FIXING OF CROSS ARM, LT

SHACKLE INSULATOR ETC. FOR FIXING OF MESSENGER WIRE AND TO PROVIDE SERVICE

CONNECTION ON AERIAL BUNCH CABLE BY INSULATED PIERCE-ING CONNECTORS THROUGH

SERVICE CONNECTION BOX COMPLETE AS REQUIRED & DIRECTED BY ENGINEER IN CHARGE.

STRINGING OF 11KV ABC OF 3*95 SQ MM +80 SQ MM INCLUDING FITTING OF ALL ACESSARIES I.E.

SPECIAL DESIGNSUSPENSION / TENSION CLAMP, FIXING OF CROSS ARM, BINDING TO PIN

INSULATOR,PREPARING SHACKLEPOINT,JUMPERS ETC. AS REQUIRED &DIRECTED BY ENGINEER IN

STRINGING OF 22 KV ABC OF 3*70 SQ MM +95 SQ MM INCLUDING FITTING OF ALL ACESSARIES I.E.

SPECIAL DESIGNSUSPENSION / TENSION CLAMP, FIXING OFCROSS ARM, BINDING TO PIN

INSULATOR,PREPARING SHACKLEPOINT,JUMPERS ETC. AS REQUIRED AND DIRECTED BY ENGINEER

STRINGING OF LT ABC OF 2*50 SQ MM +1*25 SQ MM+ 35 SQ MM INCLUDING FITTING OF ALL

ACESSORIES I.E. SPECIAL DESIGN SUSPENSION / TENSION CLAMP, FIXING OF CROSS ARM, LT

SHACKLE INSULATOR ETC. FOR FIXING OF MESSENGER WIRE AND TO PROVIDE SERVICE

CONNECTION ON AERIAL BUNCH CABLE BY INSULATED PIERCE-ING CONNECTORS THROUGH

SERVICE CONNECTION BOX COMPLETE AS REQUIRED & DIRECTED BY ENGINEER IN CHARGE.

DISMENTALING OF RSJ (9/11 METER) POLE AND CREDITING THE OLD MATERIAL TO STORE

DISMENTALING TRANSFORMER CENTER ON IO MTR,270KG PSC POLE WITHOUT TRANSFORMER WITH

CREDITING OF FABRICATION AT STORE AND STACKING OF POLE SAFELY ON ROAD SIDE OR

CREDITING TO DEPARTMENTAL STORE

DISMENTALING OF TRANSFORMERCENTER ON IOMTR,270KG PSC POLE(WITH

TRANSFORMER) WITH CREDITING OF FABRICATION AT STORE AND STACKINGOF POLE SAFELY ON

ROAD SIDE ORCREDITING TO DEPARTMENTAL STORE

DISMENTLING OF 11KV ABC OF 3*95 SQ MM +80 SQ MM AND CREDITING FITTINGOF ALL ACESSARIES

AND FABRICATION TO DEPARTMENTAL STORE

DISMENTLING OF 22 KV ABC OF 3*70 SQ MM +95 SQ MM AND CREDITING FITTINGOF ALL ACESSARIES

AND FABRICATION TO DEPARTMENTAL STORE

File No: DGVCLDVPI/tender/e-file/4448/2026/2647/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI

Letter No: DGVCLDVPI/0529/08/2026 Approved Date: 18-08-2026 07:18

DISMENTALING OF LT ABC OF 1*35 SQ MM + 1*25 SQ MM AND CREDITING FITTING OF ALL ACESSARIES

TO DEPARTMENTAL STORE.

DISMENTALING OF LT ABC OF 3*50 SQ MM +1*25 SQ MM+1*35 SQ MM AND CREDITING FITTING OF ALL

ACESSARIES TO DEPARTMENTAL STORE.

DISMENTALING OF LT ABC OF 2*50 SQ MM +1*25 SQ MM+ 1*35 SQ MM AND CREDITING FITTING OF ALL

ACESSARIES TO DEPARTMENTAL STORE.

RESTRINGING OF ALL TYPE OF CONDUCTOR (EXCEPT DOG CONDUCTOR) FOR 11/22KV & LT LINES

INCLUDING FIXING OF INSULATORS, BINDING JUMPERING ETC.

RESTRINGING OF DOG CONDUCTOR FOR 11/22KV HT LINES INCLUDING , BINDING JUMPERING ETC.

LABOUR CHARGE FOR THE INSTALLATION OF NEW DTR METER. (METER WILL BE PROVIDED BY

LABOUR CHARGE FOR THE REPLACEMENT OF DTR METER AND OLD METER SHOULD BE CREDITED

TO SDN STORE. (METERWILL BE PROVIDED BY DGVCL

LABOUR CHARGE FOR PROVIDING CT COIL FOR DTR METER CONNECTION. (CT COILWILL BE

PROVIDED BY DGVCL

LABOUR CHARGE FOR REPLACEMENT OF CT COIL FOR DTR METER CONNECTION AND OLD CT

SHOULD BE CREDITED TO SDN STORE. (CT COIL WILL BE PROVIDED BY DGVCL

LABOUR CHARGE FOR FIXING OF MMB FORDTR METER (MMB WILL BE PROVIDED BY DGVCL

LABOUR CHARGE FOR REPLACEMENT OF DTR METER BOX. (METER WILL

BEPROVIDED BY DGVCL

PROVIDING / REPLACEMENT OF 1.5 SQ MM 10 CORE COPPER CABLE 3.5 METER (CABLETO BE

PROVIDED BY AGENCY

LABOUR CHARGE FORPROVIDING/RECONNECTION OF TERMINALCONNECTION

WITH PROPER SIZE OF LUGS. LUGS COST IS BORNE BY AGENCY

LABOUR CHARGE FOR THE SPOT READINGOF DTR METER WITH DETAIL SURVEY OF DEFECT IF ANY. A

DULY SIGN COPY BY SURVEYOR PERSON OF AGENCY IN PROFORMA REPORT SHOULD BE

SUBMITTEDTO SDN ONLY IF ALLPARAMETER OF VOLTAGE, CURRENT & LOAD AS SHOWN IN PER-

FORMA IS FILLED) AS PER THE INSTRUCTION OF ENGINEER IN-CHARGE.

LABOUR CHARGE FOR THE SPOT READINGOF DTR METER WITH DETAIL SURVEY OF DEFECT IF ANY. A

DULY SIGN COPY BY SURVEYOR PERSON OF AGENCY IN PROFORMA REPORT SHOULD BE

SUBMITTED TO SDN OFFICE. (DULY FILL PER-FORMA IN FAULT CONDITION IN WHICH

READINGPARAMETER IS NOT SHOWN IN METER

INSTALLATION OF DTR METER INCLUDING METER BOX, PROVIDING & FIXING OF 1.5SQ MM SINGLE

STRAND 10 CORE ARMOURED COPPER CABLE (3.5METER), TERMINATION IN METER & COIL

BOX,CT/PT COIL WILLBE PROVIDED BY DGVCL

INSTALLATION OF DTR METER INCLUDING METER BOX, TERMINATION IN METER & COIL ETC.

(WITHOUT 10 CORE COPPERCABLE) (METER,METER BOX,CT/PT COILWILL BE PROVIDED BY DGVCL

Binding of messanger Conductorat with a distance not more than 0.75 mtr with 6 turns minimum on XLPE Cable

with single strand binding wire (including cost of binding wire)

Supply and Installation of 11/22 kV Distribution Transformers HT Terminal protector (UV Resistance) with using

95/120/150 sq.mm long barrel aluminum lug. (1Set = 3 Nos i.e. on R, Y, B)

Supply & Installation of HT EPR Tap on 11/22 kV Distribution Transformer with replacement of bare conductor by

HT ABC conductor (DO bottom side to transformer) after removal of semi conductor by HT ABC (6 inch both

side). HT ABC to be supplied by DGVCL. (1Set = 3 Nos i.e. on R, Y, B)

Supply, Installation, Testing and Commissioning of Maintenance Free, Ready Capsule, Pipe-In-Cage (Pic) Type,

Earth Electrodes for HT Feeder Pole Having 2000 mm Electrode Length as per the Tender Specifications and

Drawing. (All Materials Will Be Supplied By Agency)

Supply, Installation, Testing and Commissioning of Maintenance Free, Ready Capsule, Pipe-In-Cage (Pic) Type,

Earth Electrodes for HT Feeder Pole Having 3000 mm Electrode Length as per the Tender Specifications And

Drawing. (All Materials Will Be Supplied By Agency)

Supply and Installation of 25 X 3 mm GI Strip having hot dip- galvanized-zinc coating of 80-100 microns without

any joints or welding. Both the end of the GI strip should be connected with GI nut bolts and required fabrication

work for giving separate earthing connections to(1) Neutral of the transformer(2) MS structures of the transformer

center (Approximately 25 meter GI strip per transformer centre- as per requirement and instruction of Engineer in-

charge) (All Materials will be supplied by Agency)

Supply and Installation of uPVC standard make Pipe of 1.25" diameter for covering GI strip with UV protected

Cable Ties of 550 X 7.6 mm size to bind with pole face(Approximately 25 meter uPVC pipe for GI strip covering

per transformer centre -as per requirement and instruction of Engineer in-charge.

Supply & fixing of upto 33 kV Conducotr sleev for Busbar to Drop out Fuse and Drop out fuse to Transformer H.T.

including Busbar (12 mm sleev) as per technical specification. (All Materials will be supplied by Agency)

File No: DGVCLDVPI/tender/e-file/4448/2026/2647/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI

Letter No: DGVCLDVPI/0529/08/2026 Approved Date: 18-08-2026 07:18

Supply & fixing of upto 33 kV Conducotr sleev for Busbar to Drop out Fuse and Drop out fuse to Transformer H.T.

without Busbar (15 mm sleev) as per technical specification. (All Materials will be supplied by Agency)

Supply & fixing of upto 33 kV Conducotr sleev for Busbar to Drop out Fuse and Drop out fuse to Transformer H.T.

including Busbar(15 mm sleev) as per technical specification. (All Materials will be supplied by Agency)

Supply & fixing of upto 33 kV Conducotr sleev for Busbar to Drop out Fuse and Drop out fuse to Transformer H.T.

without Busbar(15 mm sleev) as per technical specification. (All Materials will be supplied by Agency)

Supply & fixing of Disc type Red Color FRP(Non-flammable) material with Weather resistant, Non-conductive bird

guard OD=300 MM, ID=33 MM, Width =1.25 MM, one side cut from ID to OD. (All Materials will be supplied by

Providing and fixing of LT Terminal protectors i.e. Re-useable boot (LT Side 1.1 kV) including LT (1.1 kV)

insulating taps. All live part at LT side shall be covered with fixing of LT insulating taps.

Nylon Net around Transformer Center

Nylon Net (12 * 15 ft)

Labour charge for fitting Nylon Net (All fabricated material for fitting nylon net shall be provided by DGVCL)

(B)Labour Charges for Maintenance Work

Cutting of Tree branches surrounding HT/LT line

Replacement of old jumpers & providing new double jumpers with 8" binding & capsuling with PVC pipe etc.

Support pole for stay PSC/STP/RSJ

Pin binding of conductor 11/22kv Pin insulator

Pin binding of conductor 11/22kv Pin insulator per pole in coastal area with cleaninGg .

Pin binding of conductor LT shackle insulator

Replacement of one/bothinsulator at strain pole

Replacement of LT shackle insulator at cut point

Re-fixing of V cross Arm

Re placement of V cross Arm

Re-fixing of Top fitting in proper position

Replacement of Top fitting

Replacement of LT cross Arm

Providing DO fuse on DP with carting& jumpering (ONE DO FUSE)

Numberings of pole with paint by preparing back ground of one colour and

have lettering(height 3" * width0.5" using stencil

Fixing of MMB(IPH.) at consumer end

Fixing of MMB(3PH.) at consumer end

Replacement of (Iph.) meter forUrban area

Replacement of (Iph.) meter for Rural area

painting consumer no. on MMB (Urban) (with letter size height40mm* width 8mm

painting consumer no. on MMB (Rural) (with letter size height 40mm* width 8mm

Replacement of deteriorated Single hase Service line

Fixing of new dist. Box with complete wiring includin clamps, nut bolts etc.

Repairing of guarding involving reshaping of bearer wire cross lacing binding etc.

Painting of steel fabricated material of RSJ DO DP structure with paint

Painting of steel fabricated material of RSJ pole mounted transformer double pole structure with paint

Painting of steel fabricated material of RSJ single pole with paint

painting of steel fabricated material of PSC Single pole (HT line) with paint

painting of steel fabricated material of PSC DO DP double pole with paint

painting of steel fabricated material of PSC double pole at pole mounted transformer with paint

Providing line separator single phase

Providing line separator three phase

Replacement / Providing of stay insulator along with adjustment

of tension in stay wire

Replacement of deteriorated /providing LT dist. Box with new up to 100KVA capacity & crediting it to store.

Replacement of deteriorated /providing LT dist. Box with new above 100KVA capacity & crediting it to store.

File No: DGVCLDVPI/tender/e-file/4448/2026/2647/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI

Letter No: DGVCLDVPI/0529/08/2026 Approved Date: 18-08-2026 07:18

Adjustment of tension in stay wire

Refitting of LA

Converting pin point to Shackle point including dismantling & restringing etc.

replacement of 11KV Pin insulator with providin new double in binding

replacement of 22KV Pin insulator by new 11 kv pin insulator with spares & providin new double in binding

Providing 11 kv double disc insulators with binding & restringing

Replacement of existing conductor (all size) with new double in binding

Plumbing of psc Pole with straightening at pin point

Plumbing of psc Pole with straightening at tension point

Plumbing of tilted DP structure (PSC/RSJ/STP) with refilling of stone Murrum etc.

Providing new 11 kv AB [GO switch with fabrication and insulated colour code jumper binding lugs etc.

Replacement of old 11 kv AB /GO switch with providing new insulated jumper, binding, lugs etc.

Providing cage type loop guard in vertical LT line with using PVC reel insulators etc.

Labour charges for replacement /providing of MMB & service with all

accessories for three phase connection

Labour charges for replacement /providing of MMB & service with all accessories for connection

Dismantling of existing Dist. X'mer center (RSJ/STP POLE) 25/63/100/200 KVA

with all fabrication & crediting the old material to store.

Disconnection from LT pole 1 phase

Reconnection from LT pole 1 phase (payment after receipt of R/C charges)

Disconnection from LT pole 3 phase

Reconnection from LT pole 3 phase (payment after receipt of R/C chagr es

Dismantling & removing of service line from pole & crediting to S/dn (1 phase)

Dismantling & removing of service line from pole & crediting to S/dn (3h phase )

Reconnection of service line complete with PVC cable(1 ph)

Reconnection of service line complete with PVC cable(3 ph)

Providing spiral type earthing by connecting earth terminal with earth terminal of meter box with G.I. SWG no 8 up

to 1.5meters (total weight approximately 2.2kg-20 meter in length) with salt and coal 10kg each, including pvc

rigid pipe 20mm dia (1.5mtr length) to cover exposed part of G.I. wire , providing and fixing of single core 1.5 sq

mm single strand copper insulated cable with cable nail clip to be connected with connector to G.I. wire at

consumer end as per drawing DGVCL cons. earth. Earth resistance should be less than 2 ohms(All materials

supplied by contractor .

Providing and fixing of single core 1.5 sq mm single strand copper insulated cable with cable nail clip for spiral

type earthing at consumer end. The end of G.I. no 8 is to be connected by connector with copper cable of which

other end shall be connected to the earth terminal of meter box. This item shall be used in location where there is

more distance between earth terminal and earthing terminal of meter. All materials supplied by contractor).

(C) Fabrication from Raw Materials Of Mild Steel

Fabrication of Anchor Rod from 16 SQ.mm MS Round bar & 65 mm x 65 mm x 6 mm M.S. angle as per approved

drawing and requirement of the company.

Fabrication of Anchor Rod from 16 SQ.mm MS Round bar & 50 mm x 50 mm x 6 mm M.S. angle as per approved

drawing and requirement of the company.

Fabrication of Eye Bolt from 16 SQ.mm MS Round bar with supplying of 2 (two) nuts of suitable size as per

approved drawing and requirement of the company.

Fabrication of Turn Buckle from 16 SQ.mm MS Round bar & 65 mm x 65 mm x 6 mm mm M.S. angle as per

approved drawing and requirement of the company.

Fabrication of Turn Buckle from 16 SQ.mm MS Round bar & 50 mm x 50 mm x 6 mm M.S. angle as per approved

drawing and requirement of the company.

Fabrication of 11' (feet) long Top/Bottom/D.O. angle from 65 mm x 65 mm x 6 mm M.S. angle as per approved

drawing and requirement of the company.

Fabrication of 9' (feet) long Top/Bottom/D.O. angle from 65 mm x 65 mm x 6 mm M.S. angle as per approved

drawing and requirement of the company.

Fabrication of 4'6" (feet) long Tapping / bracing angle from 65 mm x 65 mm x 6 M.S. angle as per approved

drawing and requirement of the company.

Fabrication of 2'3" (feet) long bracing/ support angle from 65 mm x 65 mm x 6mm M.S. angle as per approved

drawing and requirement of the company.

Fabrication of 11KV HT 'V' Cross Arm from 65 mm x 65 mm x 6 mm M.S. angle as per approved drawing and

requirement of the company.

File No: DGVCLDVPI/tender/e-file/4448/2026/2647/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI

Letter No: DGVCLDVPI/0529/08/2026 Approved Date: 18-08-2026 07:18

Fabrication of 11KV HT Top fitting from 65 mm x 65 mm x 6 mm M.S. angle and 50mm x 6 mm M.S. flat as per

approved drawing and requirement of the company.

Fabrication of 22KV HT Top fitting from 65 mm x 65 mm x 6 mm M.S. angle and 50mm x 6 mm M.S. flat as per

approved drawing and requirement of the company.

Fabrication of 22KV HT 'V' Cross Arm from 65 mm x 65 mm x 6 mm M.S. angle as per approved drawing and

requirement of the company.

Fabrication of Guy Clamp pair suitable for PSC pole from 50mm x 6 mm M.S. flat as per approved drawing and

requirement of the company.

Fabrication of 'U' Clamp from 50mm x 6 mm M.S. flat as per approved drawing and requirement of the company.

Fabrication of 'C' clamp suitable for PSC pole from 50mm x 6 mm M.S. flat as per approved drawing and

requirement of the company.

Fabrication of ‘C’ clamp suitable for RSJ GIRDER pole from 50mm x 6 mm M.S. flat as per approved drawing and

requirement of the company.

Fabrication of Three hole patti from 50mm x 6 mm M.S. flat as per approved drawing and requirement of the

Fabrication of 11' (feet) long Top/Bottom channel from 100 mm x 50 mm x 5 mm M.S. channel as per approved

drawing and requirement of the company.

Fabrication of 9' (feet) long Top/Bottom channel from 100 mm x 50 mm x 5 mm M.S. channel as per approved

drawing and requirement of the company.

Fabrication of 11'(feet) long angle bracing from 50 mm x 50 mm x 6 mm M.S. angle as per approved drawing and

requirement of the company.

Fabrication of 9'(feet) long angle bracing from 50 mm x 50 mm x 6 mm M.S. angle as per approved drawing and

requirement of the company.

Fabrication of 11' (feet) long channel welded from assorted length of scrap channel as per approved and

requirement of the company

Fabrication of 9' (feet) long channel welded from assorted length of scrap channel as per approved and

requirement of the company

Fabrication of Guy Clamp pair suitable for 10 mtr PSC pole from 50mm x 6 mm M.S. flat as per approved drawing

and requirement of the company.

Fabrication of Guy Clamp pair suitable for 9/11mtr RSJ GIRDER pole from 50mm x 6 mm M.S. flat as per

approved drawing and requirement of the company.

Fabrication of 5' (feet) long Tapping angle from 65 mm x 65 mm x 6 mm M.S. angle as per approved drawing and

requirement of the company.

Fabrication of H.T. Ext'n suitable for 22KV system from 65 x 65 x 6 mm M.S. angle as per approved drawing and

requirement of the company.

Fabrication of H.T. Ext'n suitable for 11KV system from 65 x 65 x 6 mm M.S. angle as per approved drawing and

requirement of the company.

Fabrication of 750 mm long Channel for HT AB conductor from 100mm x 50mm x 5mm M.S. Channel as per

approved drawing and requirement of the company.

Fabrication of 22KV HT "V" Cross Arm from 100mm x 50mm x 5mm M.S. Channel as per approved drawing and

requirement of the company.

(D) REPLACEMENT OF BARE CONDUCTOR BY HT / LT AERIAL BUNCH CONDUCTOR

Stringing of LT ABC of 1*35 SQ MM + 1*25 SQ MM including fitting of all acessaries i.e. special design

suspension / tension clamp, fixing of cross arm, LT shackle insulator etc. for fixing of messenger wire and

inclusive of dismantling charge of existing bare conductor and crediting in to store & dismentaling of service line

from LT bare conductor and to provide service connection on Aerial Bunch Cable by insulated pierceing

connectors through service connection box complete as required & directed by Engineer in Charge.

Stringing of LT ABC of 3*50 SQ MM +1*25 SQ MM+1*35 SQ MM including fitting of all acessaries i.e. special

design suspension / tension clamp, fixing of cross arm, LT shackle insulator etc. for fixing of messenger wire and

inclusive of dismantling charge of existing bare conductor and crediting in to store & dismentaling of service line

from LT bare conductor and to provide service connection on Aerial Bunch Cable by insulated pierceing

connectors through service connection box complete as required & directed by Engineer in Charge.

Stringing of 11KV ABC of 3*95 SQ MM +80 SQ MM including fitting of all acessaries i.e. special design

suspension / tension clamp, fixing of cross arm, binding to pin insulator,preparing shackle point,jumpers etc. and

inclusive of dismantling charge of existing bare conductor and crediting in to store complete as required &

directed by Engineer in Charge

File No: DGVCLDVPI/tender/e-file/4448/2026/2647/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI

Letter No: DGVCLDVPI/0529/08/2026 Approved Date: 18-08-2026 07:18

Stringing of 22 KV ABC OF 3*70 SQ MM +95 SQ MM including fitting of all acessaries i.e. special design

suspension / tension clamp, fixing of cross arm, binding to pin insulator,preparing shackle point,jumpers etc. and

inclusive of dismantling charge of existing bare conductor and crediting in to store complete as required &

directed by Engineer in Charge

Stringing of LT ABC of 2*50 SQ MM +1*25 SQ MM+ 35 SQ MM including fitting of all acessaries i.e. special

design suspension / tension clamp, fixing of cross arm, LT shackle insulator etc. for fixing of messenger wire and

inclusive of dismantling charge of existing bare conductor and crediting in to store & dismentaling of service line

from LT bare conductor and to provide service connection on Aerial Bunch Cable by insulated pierceing

connectors through service connection box complete as required & directed by Engineer in Charge.

(E)LABOUR RATE FOR UNDERGROUND CABLE WORK FOR FY 2024-25 (WITHOUT GST)

Description Rate

Labour charge for excavation of cable trench of 400mm width x 1200mm depth, in any type of soil for laying of

cable of size up to 240 mm2 (For additional cable 200 mm additional width shall be considered i.e. half trench

length is to be considered

Labour charge for excavation of cable trench of 600mm width x 1200mm depth, in any type of soil for laying of

cable of size up to 240 mm2 (For additional cable 200 mm additional width shall be considered i.e. half trench

length is to be considered

Labour charge for excavation of cable trench of 400mm width x 1500mm depth, in any type of soil for laying of

cable of size up to 240 mm2 (For additional cable 200 mm additional width shall be considered i.e. half trench

leng th is to be considered

Labour charge for laying of 11kV / 22 kV XLPE Cable of size up to 240 mm2 & preparation of sand layer 100mm

thick, in the cable trench & covering the cable with 150 mm dia (Outer), thickness 25 mm, 1.0 meter long RCC

half round muffs and providing and fixing of 4inch width yellow colour polyethylene tape with printing"CAUTION

ELECTRIC CABLE BELOW' at 0.75 m depth from ground surface after laying cable in trench. This will provide

indication that electric cable is passing underground so as to protect cable from mechanical injuries, refilling the

same, as per Instruction of E gineer in Charge (EIC) .

Labour charge for horizontal drilling using Auger machine without damage to surface road at max 2.0 mtrs depth

& putting of 6.11 kg/cm2 , class-4,Green color, 110mm 0.D. 8.5mm thickness H.D.P.E. pipe confirms to IS 4984-

1987(3rd revision) and BIS certification and laying of 11KV/22KV XLPE cable of size up to 240 mm2 in HDPE

pipe, as per Site Condition (excluding cost of pipe). The detail map obtained from HDD machine and excel sheet

hard and soft copy) indicating the respective depth and distance from adjacent landmark for each segment for

HDD is must require to be submitted. HDD to be carried out at depth 1.5 mtrs to 2.0 mtrs as per site conditions

and as er instruction of EIC.

Labour charge for horizontal drilling manually without damage to surface road at max 2.0 mtrs depth & putting of

6.11 kg/cm2 , class-4,Green color, 110mm O.D. , 8.5mm thickness H.D.P.E. pipe confirms to IS 4984-1987(3rd

revision) and BIS certification and laying of 11KV/22KV XLPE cable of size up to 240 mm2 size, as per Site

Condition (excluding cost of pipe). The detail map and excel sheet (hard and soft copy) indicating the respective

depth and distance from adjacent landmark for each segment of cable to be submitted. Drilling to be carried out at

depth Minimum 1.2 mtrs to 2.0 mtrs as per site conditions as per instruction of EIC.

Supply of 6.11kg/cm2 , class-4,Green color, 110mm O.D. , 8.5 mm thickness H.D.P.E. pipe confirms to IS

and BIS certification for laying of underground 11KV/ 22KV XLPE cable up to 240 mm 2 size.

Labour work for RCC concreting on disputed location and repairing of damage portion of road crossing for the

work carried out for roads crossing as well as concreting & muffing of poles including all materials

Providing & fixing concrete stone route marker of 300 mm width x 150 mm thick x 650 mm height embedded in

earth at least 300 mm below & 350 mm above ground level respectively at distance approx. 50 meters along the

length of cable. The RCC concreting (1:2:4)(all necessary materials will be in bidder's scope) of route marker is to

be carried out 300 mm width x 150 mm thick x 300 mm below ground level as per instruction of EIC. The route

marker should be with name of company with approved yellow colour-DGVCL. The distance from marker to cable

and cable depth with feeder name etc., marked with arrow sign is to be painted on it. The route marker is to be

fixed at location near to any fixed permanent location (not necessary to fix exact on top of cable) as per

instruction of EIC.

Erection of D.P. (double pole) structure using 9 / 11 Mtr. RSJ pole with cable connection arrangement along with

fitting of necessary fabrication for 11KV cable including excavation of pit & refilling of earth as per instruction of

EIC. (Exclusive of concreting & muffing of poles)

Erection of Single pole structure using 9 / 11 Mtr RSJ pole with cable connection arrangement along with fitting of

necessary fabrication for 11KV/22 KV cable including excavation of pit & refilling of earth as per instruction of

EIC. (Exclusive of concreting & muffing of poles

Erection of D.P. (double pole) structure using 8.0 Mtr. PSC pole with cable connection arrangement along with

fitting of necessary fabrication for 11KV cable including excavation of pit & refilling of earth as per instruction of

EIC. (Exclusive of concreting & muffing of poles

File No: DGVCLDVPI/tender/e-file/4448/2026/2647/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI

Letter No: DGVCLDVPI/0529/08/2026 Approved Date: 18-08-2026 07:18

Erection of Single pole structure using 8.0 Mtr PSC pole with cable connection arrangement along with fitting of

necessary fabrication for 11KV/22 KV cable including excavation of pit & refilling of earth as per instruction of

EIC. (Exclusive of concreting& muffing of poles

Labour charge for erecting of 11kV / 22 kV XLPE cable of size up to 240 mm 2 on DP Structure with fixing of

Nos polymer cleats on top and middle part. Polymer cleats, nut bolts etc. fixing material to be provided by

Providing & fixing of 6.11kg/cm2 , class4,Green color, 110mm O.D. 8.5mm thickness H.D.P.E. pipe confirms to

IS 4984 and BIS certification on the erected DP structure for the mechanical protection of cable by inserting the

cable inside HDPE pipe. The HDPE pipe shall be erected in such a way that 300mm shall be below the ground

level and the rest 2700 mm shall be supported on the DP Structure with 01 No Polymer cleat. All materials

including polymer cleat and Nut bolt to be provided by contractor.

Providing and fixing of pipe type earthing from 80 mm dia class-B GI pipe with pit to be filled with salt & coke and

construction of chamber as per DGVCL Drg. No. dg /100 for DP and cable. The earthing pit should be joined with

cable by G.I. strip of size 1" width & 2 mm thick. All material GI pipe, Coke Salt etc will be supplied by bidder.

Supply & fixing of heat shrink type end terminations (outdoor) for up to 11kV 3C x 185 mm2 size XLPE cable as

per DGVCL technical s ecification

Supply & fixing of heat & shrinkable end terminations (outdoor) for up to 22 kV 3C x 185 mm 2 size XLPE cable (

as per DGVCL technical specification)

Supply & fixing of heat shrinkable type end terminations (indoor) for up to 11kV 3C x 185 mm 2 size XLPE cable

as per DGVCL technical specification

Supply & fixing of heat & shrinkable end terminations (indoor) for up to 22 kV 3C x 185 mm 2 size XLPE cable as

per DGVCL technical specification

Supply & fixing of heat shrinkable straight through joint for up to 11kV 3C x 185 mm 2 size XLPE cables as per

DGVCL technical specification.

Supply & fixing of heat shrinkable straight through joint type for up to 22kV 3C x 185 mm 2 size XLPE cable as

per DGVCL technical specification

Labour charge for excavation of 2100mm long x 1200mm wide x 1200 mm deep joint pits for installation of 11kV /

22kV Straight through joints as per instruction of engineer-in-charge & covering the cable with 150 mm dia

(Outer), thickness 25 mm, 1.0 meter long RCC half round muffs & refilling same as per instruction of EIC .

Providing and fixing of insulating bus bar, made from 11KV/22KV XLPE cable after removal of semi conducting

layer and applying of PVC heat shrinkable antitracking core insulating tubing (1.1KV), on both end terminal using

Aluminium long barrel heavy duty up to 240 sq mm lugs, Aluminium bus connector. Taping with PGclamp for bus

conductor as per drawing and as per instruction of EIC. The Allurninium lugs and PG clamp shall be covered with

11KV/22KV HT insulating tapes.(11KV/22KV XLPE cable will be in scope of DGVCL while all other materials will

be in bidder's scope.

Testing of cable at various points and commissioning the feeder as per instruction of engineer-in-charge.Test

result shall be submitted by contractor with bill.

Preparation and submission of 6 (six) copies, of complete layout drawings with GIS mapping as per actual cable

routing showing road crossing, HDPE pipe sleeving, jointing locations, markers etc.

Providing and fixing of Sign Board at junction point Made out of 2 mm aluminium sheet size 750x300 mm (2.5 x

ft) rectangle, as per design, pretreated with phosphate process and acid etching coated with one coat of epoxy

primer and two coats of best quality paints, reflectorized with Hi Intensity retro — reflective sheeting as per the

latest and frame fabricated from suitable size iron angle. The Sign Board is to be fixed on the base prepared from

channel and bracing angles which is grouted by means of cement concreting of 1:2:4 for size of 300 mm dia x

800 mm height (500 mm to be grouted in ground). The details to be displayed on sign board will be given by

InchargeEngineer. (a) Hi intensity Micro prismatic Grade

Providing and fixing of Sign Board (Danger Board) on Distribution Transformer Centers Made out of 2mm

aluminium sheet size 300x300mm (1X1 ft) as per design, pre treated with phosphate process and acid etching

coated with one coat of epoxy primer and two coats of best quality paints, reflectorized with Hi-Intensity

retroreflective sheeting as per the latest and frame fabricated from suitable size iron angle. The Sign Board

(Danger Board is to be fixed at the location as per instruction of In-charge Engineer. (a) Hi intensity Micro

prismatic Grade

Providing & fixing of aluminium tag of size 250 mm (L) x 75 mm (W) from 3 mm aluminium sheet along with

mm dia aluminium binding wire for fixing of aluminium tag near end termination joint at DP structure for identifying

the cable. The details of feeder i.e. 11 / 22 KV with feeder name should be punched on the tag by letter punch of

size 16 mm as per instruction of In-charge Engineer.

Supply & fixing of heat shrink type end terminations (outdoor) for 11kV 3C x 240 mm2 size XLPE cable as per

DGVCL technical specification.

Supply & fixing of heat & shrinkable end terminations (outdoor) for 22 kV 3C x 240 mm2 size XLPE cable as per

DGVCL technical specification

File No: DGVCLDVPI/tender/e-file/4448/2026/2647/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI

Letter No: DGVCLDVPI/0529/08/2026 Approved Date: 18-08-2026 07:18

Supply & fixing of heat shrink type end terminations (indoor) for 11kV 3C x 240 mm2 size XLPE cable as per

DGVCL technical specification

Supply & fixing of heat & shrinkable end terminations (indoor) for 22 kV 3C x 240 mm2 size XLPE cable as per

DGVCL technical specification

Supply & fixing of heat shrinkable straight through joint for 11kV 3C x 240 mm2 size XLPE cables as per DGVCL

technical s ecification.

Supply & fixing of heat shrinkable straight through joint type for 22kV 3C x 240 mm2 size XLPE cable as per

DGVCL technical s ecification

Installation, Testing and commissioning of 11 KV,630 A SCADA Compatible, RRL type3 Way RMU including Two

numbers of earthings as per Drawing (material is in bidder's scope) and as per DGVCL Technical specification.

Installation, Testing and commissioning of 11 KV,630 A SCADA Compatible, RRLL type4 Way RMU including

Two numbers of earthings as per Drawing (material is in bidder's scope) and as per DGVCL Technical

Installation, Testing and commissioning of 22KV,630 A SCADA Compatible, RRL type-3 Way, RMU including

Two numbers of earthings as per Drawing (material is in bidder's scope) and as per DGVCL Technical

Installation, Testing and commissioning of 22KV,630 A SCADA Compatible, RRLL type-4 Way, RMU including

Two numbers of earthings as per Drawing (material is in bidder's scope) and as per DGVCL Technical

Construction of plinth for 11KV, RRL type- 3 Way( i.e Two numbers of Isolator & One number of Breaker) Ring

Main Unit as per DGVCL's technical specification mentioned in drawing no: Drg. 11kv-01. All required material

will be supplied by contractor.

Construction of plinth for 11KV, RRLL type4 Way (i.e Two numbers of Isolator & Two number of Breaker)Ring

Main Unit as per DGVCL's technical specification mentioned in drawing no:Drg. 11kv-02.AlI required material will

be supplied by contractor.

Construction of plinth for 22KV, RRL type- 3 Way (i.e Two numbers of Isolator & One number of Breaker) Ring

Main Unit as per DGVCL's technical specification mentioned in drawing no: Drg. 22kv-01. All required material

will be supplied by contractor.

Construction of plinth for 22KV, RRLL type4 Way (i.e Two numbers of Isolator & Two number of Breaker)Ring

Main Unit as per DGVCL's technical specification mentioned in drawing no:Drg. 22kv-02.All required material will

be supplied by contractor.

Modifications e.g. Providing and fixing ofTerminal protectors i.e. Re-use able boot (HT Side 11/22KV, LT Side

1.1KV) including 11/22 KV insulating taps and L.T.(I.I KV) insulating taps ,Busbar, Tapping from Bus Bar (11/22

KV XLPE cable) through P.G. Clamp for H.T. Jumper to D.O. Fuse to bushings of Transformer Center, providing

& Fixing of jumper and providing & fixing of Heat Shrinkable Anti Tracking CoreInsulating Tubing (Insulation Level

11/22 KV) in H.T. jumper , Clamping arrangement of cable support frame on both side of existing Over Head type

Distribution Transformer to utilize in Under Ground cable network as per drawing & as per instruction of Engineer

incharge. All live parts i.e. PGClamp, connections of D.O.fuses, HT bushings etc . shall be covered with fixing of

11/22 KV HT insulating tapes. ( 11/22 KV XLPE cable will be in scope of DGVCL while all other materials will be

in bidder's scope )

Laying of any size of 11/ 22 KV XLPE /PILCCable in readymade trench or in open space

Labour charges for lying of O/H XLPE cable pole to pole

Supply of 150 mm dia (Inner), thickness 25 mm, 1.0 meter long RCC half round pipe

TOTAL ESTIMATE- TWENTY FIVE LAKHS ONLY

Note :- All Rates are Excluding of GST.

Executive Engineer (O&M),

D.G.V.C.L.,Vapi ind. Division.

1.DGVCL will provide key material like M.S. materials,ABC/Bare conductors, PSC/RSJ Poles, Insulators,Fabricated materials

etc. to the contractor.

File No: DGVCLDVPI/tender/e-file/4448/2026/2647/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI

Letter No: DGVCLDVPI/0529/08/2026 Approved Date: 18-08-2026 07:18

2.All fabricated items shall be fabricated as per DGVCL approved drawing and by welding rods confirming to the relevent ISI

specification and as directed by engineer incharge.

3.Necessary electricity connection for fabrication items shall be provided by DGVCL on payment of required charge for

connection & electricity bill of the same shall be paid by the agency.

4.All the rates are inclusive of PF & Exclusive of GST applicable time to time.

5.All steel material are to be painted as below:

(a) Scrubbing of rusted surface properly before applying the paints on to the RSJ poles & steel fabricated materials of

RSJ/PSC poles is must required.

(b) Two coats of approved ISI mark red oxide (primer) is to be properly painted for the RSJ/PSC poles & steel fabricated

materials of RSJ/PSC poles.

(c) Two coats of approved ISI mark silver paint (i.e. triple mangoes or equivalent quality silver paint) is to be properly painted

on to the RSJ poles & steel fabricated materials of RSJ/PSC .

File No: DGVCLDVPI/tender/e-file/4448/2026/2647/Technical

Approved By: Executive Engineer,Technical,DGVCLDVPI