SPL REPAIR TO BLDG NO T-254 (TENT MOB STORE) 202 FD WKSP COY EME AND OTHER SR/LBW/REV WORKS AT CHARDUAR AREAUNDER GE (NORTH) TEZPUR

Amount

Note 1: (Applicable for all parts/items) : The biidders/contractors are advised to read tender document, all drawings & all corrigendum/amendments and general condition of contracts before entry/quoting the rates. Note 2:- Attention to bidder is hereby invited to upload revised BOQ if published during their bid submission. Uploading of incorrect/ pre-revised BOQ shall be treated as non bonafide and rejected. Fixed credit has been given in technical documents which shall be taken into account during acceptance of bid/tender.

Demolition of cement concrete (un-reinforced) in ground floors and pavings n exc 15 cm thickness ( below or above ground level) complete all as specified and directed.

Demolition of brickwork masonry built in cement mortar including all quoins, arches pillars etc complete all as specified and directed.

Demolition of reed ,lathing, single or double , including battens and plaster or chicken wire lathing complete all as specified and directed.

Dismantling of Asbestos cement (corrugated or semicorrugated etc) sheets in roof coverings complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

Dismantling of timber scantlings 40 Sqcm and over in section in any position (unframed work) complete all as specified and directed.

Dismantling of timber but in fillets, rails, posts, rafters, purlines etc.under 40 Sqcm in section complete all as specified and directed.

Taking down Chowkats or frames exc 1.5 sq.m but n exc 4 sq.m each with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down Chowkats or frames n exc 1.5 sq.m each with shutters (without taking off shutters from the frame) complete all as specified and directed.

Taking down shutters but exc 1 Sq.m and n.exc 2 Sq.m each complete all as specified and directed.

Taking down shutters n exc 1.00 sq.m each complete all as specified and directed.

Taking down cement plaster on brick work surfaces including racking out joints, hacking for key ,scrubbing down with water etc complete all as specified and directed.

Dismantling of boarding, any description, fixed in any position with nails, Complete all as specified and directed

Taking down or up steel tubing and connections inculding cleaning for refixing or removal to store 15mm bore complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connections, including cleaning for re-fixing or removal to store complete all as specified and directed.

S&F 15mm bore medium grade tubes, galvanized, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F 20mm bore medium grade tubes, galvanized, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F for straps, supports or stay for rain water, hook and pintel, clamp, hold fast, wind ties, hook for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters and smilor work conforming to Fe 290 Gde E-165 complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Framed work such as grills,gratings,etc with ends of bars shouldered and/or riveted,or forged into spikes, framed guard bars barred iron doors,ladders,framed balusters,walkways,railingsframework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

S&F mild steel angle iron/MS pipe post as in purlins crane gantries, rails, ceiling and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc. using Fe 410-W (Gde E-250) quality B complete all as specified and as directed.

M&L brick work with subclass ‘B’ bricks, straight or curved on plan exc 6 m mean radius built in Cement mortar 1:6 complete all as specified and as directed.

M&L for brickwork with sub class’B’ bricks, straight or curved on plan exc 6m mean radius in half brick work built in CM 1:4 complete all as specified and as directed.

M&L GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding , joists, etc. In walls, ceilings, stanchions, beams, bird proofing etc. Including all laps , cutting and waste complete all as specified and as directed.

M&L for 10mm thick plastering on fair faces of bricks or concrete surfaces finished even and smooth without using extra cement in CM(1:6) complete all as specified and as directed.

M&L for rendering 10 mm thick plastering but as in CM 1:4 on other than fair faces of brick work and 5mm thick floating/setting coat using water proofing compound over it complete all as specified and as directed.

M&L for rendering 10 mm thick plastering but on one side of lathing in CM 1:4 complete all as specified and as directed.

M&L for rendering 10 mm thick plastering but on other side of lathing and 5mm thick floating/setting coat using water proofing compound over it in CM 1: 4 complete all as specified and as directed.

Supply only water proofing compound complete all as specified and as directed.

M&L for second class wrought hard wood in scantlings (Timber fixed) complete all as specified and as directed.

M&L for 50mm thick planed at both sides boarding as in rafters,truess and members complete all as specified and directed.

M&L for 20mm thick second class hardwood planed at both sides boarding as in eaves boards incl dismantling old boarding, any description, fixed in any position with nails complete all as specified and as directed.

M&L for 4mm thick asbestos cement plain building boards, fixed to timber framework in ceiling/wall / sunsheds with screws/ nailing complete all as specified and as directed.

M&L for 2nd class hard wood plain fillets ,square, rectangular or triangular in section ,clean sawn ,secured with nails or brads (sectional area exc13 sq.cm & n exc 25 sq.cm)as in studs of ceiling / sunshed/ wall panelling frame complete all as specified and as directed.

All as per item No-35.00 but (sectional area exc6 sq.cm & n exc 13 sq.cm) as in bird proof etc complete all as specified and as directed.

S&F for second class hardwood plain,solid,straight,chowkats and frames,wrought,framed rebated on the solid ,rounded or chamfered ,put together with glue pinned at joints complete all as specified and as directed.

S&F Flush shutters 35 mm thick, solid core construction, with block board core and plywood dace panels, commercial type on both sides incl provision of suitable blocks for taking mortice locks, latches or other fittings complete all as specified and as directed.

S&F 2nd class H/W glazed and skeleton shutters 35mm thick open rebated and prepared to received glass, without (sash bars), edges of framing plain , chamfered or rounded fitted with cut and mitred beads for securing glass etc sizes of members of shutters as specified in SSR Part-I, Section 1 Clause 8.20 (a) complete all as specified and as directed.

S&F 30mm thick glazed and skeleton shutters 2nd class hard wood , open rebated and prepared to receive glass, gauge etc divided into squares, with plain, cham-fered or rounded, mitred and rebated sash bars provided with stiles and rails as specified in SSR Part I ,section 8 clause8.20(b) complete all as specified and as directed.

S&F 100mm medium weight ,cold rolled mild steel butt hinges (ISI Marked) complete all as specified and as directed.

S&F 75 mm medium weight ,cold rolled mild steel butt hinges (ISI Marked) complete all as specified and as directed.

S&F 50 mm medium weight ,cold rolled mild steel butt hinges (ISI Marked) complete all as specified and as directed.

S&F 150mm anodised aluminum handles, cast type (ISI Marked) complete all as specified and as directed.

S&F 100mm anodised aluminum handles, cast type (ISI Marked) complete all as specified and as directed.

S&F 300mm long anodised aluminium alooy sliding door bolts with hasp, stable (bolt type) and fixeing clips of sheet (ISI Marked) complete all as specified and as directed.

S&F 150mm long anodised aluminium barrel tower bolts of extruded section (ISI Marked) complete all as specified and as directed.

S&F 100mm long anodised aluminium barrel tower bolts of extruded section (ISI Marked) complete all as specified and as directed.

S&F 300mm MS ordinary rat tail rod pattern springs, incl roller plate (ISI Marked) complete all as specified and as directed.

S&F in repairs Galvanized wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or galvanized wire staples complete all as specified and as directed.

S&F for 3.00mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.50.m in each pane complete all as specified and as directed.

M&L for 25 mm thick cement concrete type B-1, 1:2:4 (using 20 mm graded crushed stone aggregate) complete all as specified and as directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc complete all as specified and as directed.

Treating old cement concrete floor with brushing neat cement slurry with 3.0 Kg of cement per Sqm complete all as specified and as directed.

M&L for screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM 1:4 complete all as specified and as directed.

M&L for rendering 10 mm thick screed bed on fair faces of brickwork surfaces in CM 1:3 to receive wall finishes complete all as specified and as directed.

M&L for Non Skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to matchcomplete all as specified and as directed.

M&L for coloured glazed ceramic tiles 200x 300x7 mm thick, in vertical surfaces, skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as directed.

M&L for preparation of surfaces of new wood and wood based materials,of any description,not otherwise described, over 10 cm width or girth, and applying with two coats of synthetic enamel paint over coat of pink primer complete all as specified and as directed.

all as per item No-59.00 above but not exc 10 cm width or girth complete all as specified and as directed.

M&L for preparation of surfaces of old wood and wood based materials, of any description,not otherwise described,over 10 cm width or girth,and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for preparation of new or previously untreated steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enameled paint over one coat of red oxide primer complete all as specified and as directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of putty complete all as specified and directed.

M&L for preparation of old Plastered surfaces of wall after complete removal of existing treatment and applying two coats of oil bound distemper over a coat of putty complete all as specified and directed.

M&L for preparation of old Plastered surfaces of wall after complete removal of existing treatment and applying two coats of cement based paint complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement based paint complete all as specified and directed.

M&L for Preparing surface of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with two coats of creosote oil complete all as specified and directed.

M&L for preparation of new or old surfaces of ceilings and applying three coats of white wash complete all as specified and directed.

M&L for 40 mm thick cement concrete type B-1,1:2:4( using 20mm graded crushed stone aggregate) as in floor th and making finished even and smooth with using extra cement complete all as specified and directed.

M&L for 75mm thick cement concrete type C-2,1:3:6( using 40mm graded crushed stone aggregate) as in plinth protection ,footpath, flooring/ sub base complete all as specified and directed.

M&L for plain cement concrete type-C2 1:3:6 (using 40mm graded crushed stone aggregate) in surface channel and drains complete all as specified and directed.

Extra for forming fair finished drain or channel any girth in cement concrete using extra cement including forms, moulds mitred/stopped ends etc complete all as specified and directed.

S&F 1mm thick mild steel sheet eaves gutters 150mm dia, galvanised class 3, half round woth rounded edges complete all as specified and directed.

M&L Hardcore of gauge n exc 63 mm, deposited, spread and levelled in layers n exc 15 cm thick watered and rammed to a true surface with broken bricks complete all as specified and directed.

M&L for sand filling under floor or below paver blocks including watering and consolidation complete all as specified and directed.

M&L for coloured machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade with grey cement and pigment complete all as specified and directed.

M&L for PCC, 1:2:4 type B1,(using 20mm graded crushed stone aggregate) in lintels upto 1..5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded for chamfered angles and throating,complete all as specified and directed.

Demolition of reinforcement cement concrete in any description and in any position not otherwise specifically provided for complete all as specified and directed.

S&F Stainless steel sink, 1.00 mm thick for kitchen with plus, waste pipe, washers, including cantilever cast iron brackets, connecting union etc, overall size 495mm x 420mm with bowl size 410mmx330mm x 160mm complete all as specified and directed.

M&L for granite slab green/black colour as in cooking platform 18 to 20 mm thick over cement screed bed with pre grinding and mirror polishing/granite polishing and chamfering the corners complete all as specified and directed.

S&F in repair 15mm dia angle cock of CP any colour high pressure screwed for iron pipe complete all as specified and directed.

S&F in repair 15mm dia chromium plated bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified and directed.

Dismantling water tanks of capacity exc 500 & nexc 1000 litres and removing to store complete all as specified and directed.

S&F 1000 litre capacity ,rotational moulded polyethylene water storage tanks (Cylindrical vertical with closed top) in position all specified in SSR Part –I complete all as specified and directed.

M&L Ball valves (20 mm) high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/ 40mm- 690 gms/ 50mm-1240 gms) complete all as specified and directed.

S&F in repair 20mm dia gate metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and directed.

S&F Pillar taps long body , cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed.

S&F in repair vitreous China wash basin, white, flat back, size 500x400mm (flat back or angle back type) including brackets, cutting for and pinning 'in brackets waste coupling, waste pipe, grating complete all as specified and directed.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

S&F PVC (SWR) floor trap 75 mm, setting and jointing with solvent cement complete all as specified and directed.

S&F 75mm bore PVC ( SWR) pipes single socketed ,in any length with rubber ring joints, fixed to wall complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) bends of radius 75mm bore complete all as specified and directed.

S&F PVC (SWR) junction single,(Single T) equal or unequal of radius 75mm bore complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) bends of radius 110mm bore complete all as specified and directed.

S&F PVC (SWR) junction single,(Single T) equal or unequal of radius 110mm bore complete all as specified and directed.

M&L for R.C.C 1:2:4 type B1 (usig 20mm quoted agg) as slabs supported on walls, beams and columns in floors, roofs, landing, balconies, cover slabs complete all as specified and directed.

M&L for M.S. TMT bars 8 to 10 mm dia bent to shape required including cranking bending and binding with M.S wire not less than 0.9mm dia complete all as specified and directed.

M&L for Form work to rough finished edges of concrete flats soffits of suspended slabs flat or batter such as roof slabs, floor slabs and similar work not exceeding 200 mm thick complete all as specified and directed.

M&L for 12mm pre-laminated particle board, interior grade, prelaminated one side with decorative choice laminated & other side balancing white laminated, fixed with screws to timber/steel frame work complete all as specified and directed.

M&L for 4mm thick 3 No of ply plywood, grade BWR type BB fixed with screws to timber frame work complete all as specified and directed.

Excavating post holes (or similar holes ) each n.exc 0.5 cum getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25 cm, watering and removing surplus soil to a distance n exc 50m and making good surface complete all as specified and directed.

Surface dressing n exc 15cm deep soft/loose soil complete all as specified and directed.

M&L plain cement concrete type 1:4:8 type C2( using 40mm crushed stone aggregate) in foundations, filing & mass concrete complete all as specified and directed.

S&F for steel work in tubular trussess / posts including special shaped washers etc complete using ERW or including butt welded tubes confirming to IS 1161 - 1979 grade St -240., structural steel is painted one shop coat of zinc chromate primer paint (incl preparation of surface) at contractor's workshop before fabrication complete all as specified and directed.

S&F Mild steel screw bolts( 11mm to 15mm dia) (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut n exc 5 cm complete all as specified and directed.

S&F Galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with coach screws and washers, in roofs, walls etc. with grade of zinc coating 275 complete all as specified and directed.

M & L for 100mm thick plain cement concrete type C2,1:3:6 using 40mm agg maintaining panels as in sub-base of hardstanding/footpath / plinth protection complete all as specified and directed.

Excavation in trenches, nexc 1.5 m wide and nexc 1.5 m in depth, for foundation, etc. or for shafts, wells, cesspits, Manhole, Pier Holes, etc and getting out soft/loose soil complete all as specified and directed.

Surfaces excavation nexc (not exceeding) 30 cm deep and averaging 15 cm depth and getting out in soft/loose soil complete all as specified and directed.

M&L for rendering 15mm th in CM 1:4 on fair faces of brick finished even & smooth without using extra cement complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate as in coping complete all as specified and directed.

Removing excavated materials(Soil) n. exc 50 mtr and depositing where directed at level n.exc 1.5 mtr above the starting point complete all as specified and directed.

M&L for 75mm thick cement concrete type C-2,1:3:6(40mm graded aggregate) as in plinth protection ,footpath and making finished even and smooth without using extra cement complete all as specified and directed.

M&L for sand filling under floor or below paver blocks including watering and consolidation complete all as specified and directed.

M&L for coloured machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade with grey cement and pigment complete all as specified and directed.

M&L for Taking down of shutters of any descriptions exc 1 sqm but n.exc 2 sqm each and refixing in same opening complete all as specified and directed.

S&F 10 litres PVC Syphonic action type, Flushing cistern, high level, with inlet, ball valve, float chain and pull incl flush pipe 32mm dia complete all as specified and directed.

S&F 100mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F 100mm grating doom 100mm dia of PTMT complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 300/450mm complete all as specified and directed.

S&F 15mm bore stop valves/angle cock, fancy type, chromium plated cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F 15mm bore bib taps, chromium plated cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

M&L for PCC, 1:2:4 type B1,(using 20mm graded cr stone aggr in lintels upto 1..5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded for chamfered angles and throating complete all as specified and directed.

M&L for 75 mm thick cement concrete type D-2,1:4:8(using 40mm graded crushed stone aggregate) as in sub base under floor complete all as specified and directed.

M&L for 15mm thick plastering on fair faces of bricks or cone surfaces finished even and smooth w/o using extra cement in CM1:4 complete all as specified and directed.

M&L for PCC coping type C-1, 1:3:6 (using 20mm graded crushe stone aggregate) finish even and smoooth complete all as specified and directed.

Returning, filling in, including spreading leveling watering and well ramming in layers n,exc 25 cm thick in soft /loose soil for sewage pipe line /manhole and cleaning the site complete all as specified and directed.

Removing excavated materials(Soil) n. exc 50 mtr and depositing where directed at level n.exc 1.5 mtr above the starting point complete all as specified and directed.

S & F MS framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc, complete drilled for fixing of steel sheeting or other covering, doors etc., to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides ) and hanging also fastening and fixing complete conforming to Fe-410-S complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10cm in girth or width & applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed.

M&L for preparation of new surfaces of wall and applying three coats of white wash complete all as specified and directed.

Excavation over areas in soft/loose soil n exc 1.5m depth and getting out complete all as specified and directed.

M&L brick work unsing sub class B brick curved or straight in plan exc 6 mtr mean radius in cm (1:4) complete all as specified and directed.

M&L Brickwork with sub class ‘B’ bricks in one brick thick honey comb walling, built in CM 1:3 complete all as specified and directed.

M&L for precast cement concrete cover slabsType B1 1:2:4(using 20mm graded crushed stone agg) set in cement mortar 1:4 complete all as specified and directed.

M&L for M.S. TMT bars 8 to 10 mm dia bent to shape required including cranking bending and binding with M.S wire not less than 0.9mm dia complete all as specified and directed.

M&L for rendering 15 mm thick plastering but as in CM 1:4 on other than fair faces of brick work complete all as specified and directed.

M&L for Loose filling with aggregates of gauge 80 to 150 mm in soakage pits, soakage wells complete all as specified and directed.

S&F 110mm dia PVC (SWR) vent cowl complete all as specified and directed.

S&F 110mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

M&L for 1:3:6 type C2 cement Concrete bed to drain pipe 110mm including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed

M&L for 75 mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregatein plinth protection or similar places laid in alternate way surface finished even and fair wthout using extra cement complete all as specified and directed.

M&L for use and waste of form work to sides of concrete foundation, footing, bases of columns, rafts and raft beams, sides and soffits of foundation and plinth beams and similar work,vertical or to the batter of rough finished surface complete all as specified .

M&L for formwork to the sides of square columns, pillars etc of rough finished surface complete all as specified and directed.

M&L for formwork to sides and soffits of floor or roof beams,lintel,cantilevers,shelves etc including support of rough finished surface of concrete flat complete all as specified and directed

S&F TMT bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F TMT bars 6 to 8mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified.

S&F mild steel TMT bar 5 to 10 mm dia as in stirrups cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

M&L for RCC (1:1.5:3) nominal mix (using 20 mm graded crushed stone aggregate) as in column footing including raft footings, foundation, plinth beam, bases of column etc complete all as specified and directed.

M&L for RCC (1:1.5:3) nominal mix (using 20 mm graded crushed stone aggregate) as in columns, pillars etc complete all as specified and directed.

M&L for RCC (1:1.5:3) nominal mix (using 20 mm graded crushed stone aggregate) as in Plinthbeam, roof beam, cantilevers, lintel beam,etc complete all as specified and directed.

M&L for plain cement concrete type D2 1:4:8(using 40 mm graded crushed stone aggregate) in foundations, filing & mass concrete complete all as specified and directed.

M&L for 75 mm thick cement concrete type D-2, 1:4:8 (using 40 mm graded crushed stone aggregate) as in sub base under floor complete all as specified and directed.

M&L for 40 mm thick cement concrete type B-1, 1:2:4 (using 20 mm graded crushed stone aggregate) to receive the top layer of tiles complete all as specified and directed.

M&L for 20mm thick in cement mortar 1:2 damp proof course to horizontal or vertical surfaces with WPC including necessary formwork, complete all as specified and directed.

M&L 15mm thick plastering on fair faces of bricks or cone surfaces finished even and smooth without using extra cement in CM 1:4 complete all as specified and as directed.

M&L for rendering 10 mm thick plastering on fair faces of brickwork surfaces in cement mortar (1:6) making smooth and even surfaces without using extra cement complete all as specified and as directed.

M&L for providing precast cement concrete type B1 1:2:4 (using 20mm graded crushed stone aggregate) in door cills, lintels bressumers, copings and setting in cement mortar 1:4 complete all as specified and directed.

All as per item No-162.00 above but in landings, cover slabs for manholes and similar articles with palin faces complete all as specified and directed.

M&L screed bed or bedding layer of mortar 20mm thick for laying floor finishes in CM 1:4 complete all as specified and directed.

M&L for rendering 10 mm thick screed bed on fair faces of brickwork surfaces in CM 1:3 to receive wall finishes complete all as specified and directed.

M&L for Vitrified ceramic tiles 10mm polished area of each tiles n exc 0.36 Sqm in floors and as in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

S&F Anodised aluminium snap grid frame of size 605 x605 work for false ceiling including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof by means of ceilling cleats/ 2 mm dia wire made out of G.I. flat 40 x 3 mm size 60mm complete all as specified and directed.

S&F Mild steel screw bolts(15mm dia) (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut complete all as specified and directed.

S&F Fe 410-W(Gde-E250) Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters fixed with angle cleats or other connectings plates complete all as specified and directed.

M&L for preparation of new plastered surface and applying two coats cement base paints on walls complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of oil bound distemper over a coat of putty complete all as specified and directed.

M&L for preparation of new steel surface over 10 cm with or grith and applying two coats of synthetic enamel paint over a coat of redoxide complete all as specified

S&F anodised aluminium frame door, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F anodised aluminium door shutters, aluminium section weighning 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles two Nos in each door, hinges anodised aluminum snap beading screw etc complete all as specified and directed.

M&L for Anodised aluminium window or ventilator (sliding type) shutters /fixed type without sash bars necessary joining cleats , glazing clips ,rubber neoprene packing handles 2 Nos in each doors hinges anodised aluminium snap beading, screws,roller bearing etc complete all as specified and directed.

M&L for Sheet glass 5mm ordinary quality and glazing with oil putty in square n exc. 0.50sqm in each pane complete all as specified and directed.

M&L for Sheet glass 5mm thick ordinary quality and glazing with oil putty in square exc. 0.50sqm in each pane complete all as specified and directed.

S&F Door closer hydraulicaly regulated(Aluminium ,extruded section),designation No.3,universal type ,suitable for door shutters of 851 to1000mm in width and of weight between 61 to 80 kg complete all as specified and directed.

M&L 12mm Perforated particle board/tiles for insulation and accoustic purposes, 60x60 cm in size, fixed with staples on snap grid complete all as specified and directed.

Returning, filling in, including spreading leveling watering and well ramming in layers n,exc 25 cm thick in soft /loose soil for sewage pipe line /manhole and cleaning the site complete all as specified and directed.

Removing excavated materials(Soil) n. exc 50 mtr and depositing where directed at level n.exc 1.5 mtr above the starting point complete all as specified and directed.

E/M PORTION

Taking down carefully aluminium conductor point wiring (light, socket or power) complete including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. to match with the existing complete all as specified and directed.

Taking down old/defective ceiling fans of any size/sweep and transproting these to MES store yard for deposition and supply & fixing ceiling fans 1200mm sweep complete with blade and white in colour including provision of PVC insulated copper multi starnded three core flexible cable for making necessary electrical connections from ceiling rose to connector all as required at site complete all as specified and directed.

M&L point wiring for light point/fan or bell point controlled by one, one way switch or bell push using 1.5 Sq mm nominal cross sectional area multi stranded copper conductor wire, PVC insulated unsheathed FRLS cables drawn in and including rigid PVC concealed conduit of suitable size with fittings complete fixed to wall/ceiling including sheet steel recessed boxes ISI marked with top sheet factory made 3mm thick for mounting of switches/sockets/regulators/bell push etc and 1.5 Sq mm nominal cross sectional area multi stranded copper conductor cable (Green colour), PVC insulated sheathed used as earth wire and connecting to earth dolly by means of screws, washers etc complete all as specified and directed.

Ditto all as item No-185.00 above but for 5 Amps socket point on same board complete all as specified and directed..

M&L point wiring for one 3 pin 15 amps socket point on independent board by using 2.5 Sq mm nominal cross sectional area multi stranded copper conductor wire, PVC insulated unsheathed FRLS cables drawn in and including rigid PVC concealed conduit of suitable size with fittings complete fixed to wall/ceiling including sheet steel recessed boxes ISI marked with top sheet factory made 3mm thick for mounting of switches/sockets/regulators/bell push etc and 2.5 Sq mm nominal cross sectional area multi stranded copper conductor cable (Green colour), PVC insulated sheathed used as earth wire and connecting to earth dolly by means of screws, washers etc complete all as specified and directed.

M&L point wiring for light/fan/bell point controlled by one, one way switch/bell push using 1.5 Sq mm nominal cross sectional area multistranded FRLS copper conductor, PVC insulated sheathed cables in and including casing & capping of suitable size with fittings complete fixed to wall/ceiling including PVC closed factory fabricated boxes with top sheet ISI marked for mounting of switches/sockets/regulators/bell push etc and 1.5 Sq mm nominal cross sectional area multistranded FRLS copper conductor cable PVC insulated sheathed earth wire and connecting to earth dolly by means of screws, washers etc. complete.

M&L wiring for one 3 pin socket outlet 5 amps on independent board using 1.5 Sq mm nominal cross sectional area multistranded FRLS copper conductor, PVC insulated sheathed cables in and including casing & capping of suitable size with fittings complete fixed to wall/ceiling including PVC closed factory fabricated boxes with top sheet ISI marked for mounting of switches/sockets etc and 1.5 Sq mm nominal cross sectional area multistranded FRLS copper cable PVC insulated sheathed earth wire and connecting to earth dolly by means of screws, washers etc complete all as specified and directed.

M&L wiring for one 3 pin socket outlet 15 amps on independent board using 2.5 Sq mm nominal cross sectional area multistranded FRLS copper conductor, PVC insulated sheathed cables in and including casing & capping of suitable size with fittings complete fixed to wall/ceiling including PVC closed factory fabricated boxes with top sheet ISI marked ISI marked for mounting of switches/sockets etc and 2.5 Sq mm nominal cross sectional area multistranded FRLS copper cable PVC insulated sheathed earth wire and connecting to earth dolly by means of screws, washers etc complete all as specified and directed.

S&F Polycarbonate Switch piano flush type, SP, 6 Amps, one way complete all as specified and directed.

S&F Polycarbonate socket out let 2 in 1 socket 3 pin, 5/6 Amps flush type controlled by one switch complete all as specified and directed.

S&F Polycarbonate switch socket out let 2 in 1 socket 3 pin, 5&15 amps flush type controlled by one 15 Amps switch complete all as specified.

S&F ceiling fan regulator electronic step type (5 steps) 240 volts 100 watts, ISI marked and connecting electrically complete all as specified and directed.

S&F lamp holder, insulated body, angle holder PVC/Polycarbonated type with back plate complete all as specified and directed.

S&F ceiling rose surface bakelite 65x50mm two to three terminals and making all electrical connections complete all as specified and directed.

S&F sheet metal enclosure MCB DB double door 4 ways with 200 Amps rated bus bar SPN 240 volts complete including making all electrical connections complete all as specified and directed.

S&F MCB single pole and neutral 40amps 240 volts rating and to be housed in DBs catered here in before complete including making necessary electrical connections complete all as specified and directed.

S&F MCB single pole 6-32 amps 240 volts rating and to be housed in DBs catered here in before complete including making necessary electrical connections complete all as specified and directed.

S&F ceiling fans 1200mm sweep of 3 star rating complete including provision of PVC insulated copper multi stranded three core flexible cable of suitable length for making necessary electrical connections from ceiling rose to connector all as required at site complete all as specified and directed.

M&L for one twin core cable flat or circular, 1100 volts grade heavy duty cable, PVC insulated, with stranded aluminium conductor, size 10 Sqmm served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating in service hangers not more than 1 metre apart including 4mm GI suspension wire, and including taking down of unserviceable service connection complete all as specified and directed.

M & L Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of the earth plate at a depth not less than 1.5 mtr below ground level earth plate surrounded from all sides by 15cm thick packed layer of charcoal dust and common saft filling in alternate layers and electrode connection by using earth lead GI wire 4mm dia by means of bolts, nuts, check nuts and washers made of galvanised iron and thimbles and other end of the earth wire connected to main switch board protected by galvanised iron light grade pipe 15mm bore in wall/floor/and GI Pipe 20mm bore light grade for watering with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC pit cover including necessary excavation and earth work in any type of soil, returning slurry approved soil and disposed of surplus soil to a distance not exceeding 50 Mtr away all as shown in Electrical Plate No 3 of SSR 2009( Part-I) including dismantling of existing earthing of any description complete all as specified and directed.

S&F Polycarbonate switch socket out let 2 in 1 socket 5 pin, 5&15 amps flush type controlled by one 15 Amps switch, complete all as specified including making necessary electrical connections as requierd at site complete all as specified and directed.

S&F Bell push, flush type, 5 amp including making necessary electrical connections as requierd at site complete all as specified and directed.

S&F Bell, AC, 230 volts, single pole including making necessary electrical connections as requierd at site complete all as specified and directed.

S&F wall mounted LED batten extruded aluminium heat shrink provided for efficient heat dissipation and integrated electronic driver lamp type 40 watt 6000K 4 feet including making necessary electrical connections with three core PVC insulated copper flexible cable 1100 volts grade of suitable size and length complete all as specified and directed. Make- Surya Roshni Cat Part No -SLE BTN T8 40W or Equivalent of (i) Bajaj (ii) Wipro (iii)Philips

S&F wall mounted LED batten extruded aluminium heat shrink provided for efficient heat dissipation and integrated electronic driver lamp type 20 watt 6000K 2 feet including making necessary electrical connections with three core PVC insulated copper flexible cable 1100 volts grade of suitable size and length complete all as specified and directed. Make- Surya Roshni Cat Part No -SLE BT 20 IL or Equivalent of (i) Bajaj (ii) Wipro (iii)Philips

S&F new generation energy saving environment friendly long life LED street light made up of pressure die cast aluminium housing with high power LEDs as light source and lens embedded PC cover with IP-66 protection and impact resistance of IK07 having 45 watt 5700K LED with prewired and necessary mounting/fixing arrangement with wall of any description complete with fixing material such as clamps,nuts,bolts etc and connecting complete all as specified and directed including taking down of old/unsv street light fitting of any description complete all as specified and directed. Make- Surya Roshni Cat Part No -SLE UL 45W IP66 PLX or Equivalent of (i) Bajaj (ii) Wipro (iii)Philips

S&F in replacement of 10 watt LED new adore 10WB22 cool day light ball lamp complete all as specified and directed.

S&F in replacement sheet metal enclosure MCB DB double door 8 ways with 200 Amps rated bus bar SPN complete all as specified and directed.

S&F MCB SP 6-32 amps 240 volts rating and to be housed in DBs catered here in before complete including making necessary connections with suitable size thimbles etc complete all as specified and directed.

S&F MCB SPN 6-32 Amps B series 240 volts rating and to be housed in DBs catered here in before complete including making necessary connections with suitable size thimbles etc complete all as specified and directed.

S&F single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps including making necessary connections with suitable size thimbles etc complete all as specified and directed.

M&L in repairs for fan hook made out of mild steel flat iron of size 40mm x 5mm and 66 cm long including taking down old unserviceable fan hook, complete all as specified and directed.

M&L for submain wiring with two runs of PVC insulated multistranded, copper coductor of size 6 Sqmm cable single core 1100 Volts Grade and one run of earth continuity conductor cable of 6 Sq mm solid strand cable drawn in and incl 30/32 mm PVC casing caping complete all as specified and as directed. Note:- 2 run of cable and one run of earth wire including one run of casing capping shall be measured as one unit.

M&L for house service bracket (hook type) complete with 3 mtrs long GI pipe 40mm dia, medium grade, 2 Nos 90 degree MS hook and stay or gay on the wall by grouting cement mortar and make good all disturbed surfaces complete all as specified and directed.

S&F Exhaust fan heavy duty 300mm with louver, AC single phase 240 volts 900 RPM fixed on wall with necessary electrical connections with 3 core copper flexible multistranded cable of suitable size and connecting with ceiling rose including making hole/niche in wall to fix the fan and necessary arrangement for fixing such as frame,nuts,bolts and washers all as required at site complete all as specified and directed.

S&F Exhaust fan heavy duty 250mm with louver, AC single phase 240 volts 900 RPM fixed on wall with necessary electrical connections with 3 core copper flexible multistranded cable of suitable size and connecting with ceiling rose including making hole/niche in wall to fix the fan and necessary arrangement for fixing such as frame,nuts,bolts and washers all as required at site complete all as specified and directed.

Supply, installation, testing and commissioning water heater storage type, electrically operated of capacity 25 litres having stainless steel body with PUF insulated steel tank,thermostat, thermal cut off,glass coated heating element of 1.5 KW, vertical type with reset option including making all electrical and water supply connections of inlet and outlet points with suitable size PVC pipe of suitable length and suitable for hot and cold water as required at site including necessary nuts,bolts and washers of required size and depositing the old geyser in store yard of AGE Charduar complete all as specified and directed.

S&F in replacement of bracket for street light fitting fabricated with 1200 mm long and 40 mm bore medium grade GI pipe bent to shape as required and fixed in position including necessary clamps,nuts,bolts & washer complete all as specified and directed.

Raj Enterprise

M/S L N ENTERPRISE

M/s Adil Construction