ADDN ALTN AND SPECIAL REPAIRS TO CIVILIAN MD ACCN P 389 AND P 390 AT INS VALSURA JAMNAGAR

Amount

ADDN/ALTN & SPECIAL REPAIR WORKS

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing) complete all as specified and directed.

Demolition of un reinforced concretein ground floors and Pavings not exc 15 cm thick (below or above ground level ) complete all as specified and directed

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed

Taking down wooden/steel frame not exceeding 1.5 Sqm each (Without taking off shutters from the frames) complete all as specified and directed

Taking down wooden/Steel frame exceeding 1.5 Sqm and not exceeding 4.00 Sqm each (Without taking off shutters from the frames) complete all as specified and directed

Taking down shutter of any description exc 1 Sqm and n exc 2 Sqm each complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc.complete all as specified and directed

Demolition & breaking up 100mm bore AC/Concrete Pipe set in cement mortor complete all as specified and directed

Dismantling water tanks (PVC) exceeding 250 ltr and not exceeding 500 ltrs capacity complete all as specified and directed.

Complete removal of old existing treatment of any thickness from RCC roof by stripping out old tar felt over roofs, parapets, chimney stacks etc as laid horizontally or vertically including taking out layer of cement plaster and PCC of any thickness over RCC roof surface if any comletely by scrapping/scrubbing/brooming down etc and cleaning the surface all as specified and directed.

15 mm thick rendering in CM 1:4 on fair faces of brick work or concrete surface mixed with water proofing compound and finished the surface even and smooth without using extra cement complete all as specified and directed.

Cleaning the plastered surface very neately, priming surfaces and applying normal treatment (for moderate conditions) using glass fibre base bitumen felt, grade 2 @ 0.500 kg per sqm over cleaned plastered surfaces of roof all as specified.

Cutting out crcks to 'V' section in existing roof or terrace,cleaning out,wetting,grouting with cement and sand slurry 1:3 complete all as specified and directed.

PCC 1:2:4, type B0 using 12.5 mm graded stone aggregatee as padding concrete to the roof slab etc complete all as specified and directed

Water proofing treatment by applying oil bound bituminous primer 0.20 kg/sqm, providing and laying 4mm thk APP modified water proofing membrane weighing not less than 4 kg/sqm, reinforced with non-woven polyster matt weighing not less than 160 g/sqm, having softening point not less than 1400 C longitidunal tensile strength not less than 650 N/Sqcm tearing strength of 180 N by torque application including minimum 10 cm side overlap and 15 cm overlap and applying a coat of blown grade hot bitumen 85/25 over the membrane @ 1.2 kg/sqm finishing the surface with solar reflective bituminous aluminium paint @ 100 gm/sqm, complete all as specified and as directed by Engr-in-Charge and as per manufacturer's instructions.

Water proofing treatment by applying oil bound bituminous primer 0.20 kg/sqm, providing and laying 4mm thk APP modified water proofing membrane weighing not less than 4 kg/sqm, reinforced with non-woven polyster matt weighing not less than 160 g/sqm, having softening point not less than 1400 C longitidunal tensile strength not less than 650 N/Sqcm tearing strength of 180 N by torque application including minimum 10 cm side overlap and 15 cm overlap and applying a coat of blown grade hot bitumen 85/25 over the membrane @ 1.2 kg/sqm finishing the surface shall be done using PCC tiles of size 300x300x25mm machine made laid over 20mm thick cement morter 1:4,set, jointed and pointed in cement morter 1:3 mixed with 5% curd oil by weight of cement over APP membtane complete all as specified and as directed by Engr-in-Charge and as per manufacturer's instructions.

25mm thick, PCC 1:2:4 type B0 , using 12.5mm graded crushed stone aggregate for leveling the undulation floor after dismantling complete all as specified and directed

Joint free non skid Coloured ceramic tiles of 7 to 8 mm thick (Square/Rectangular) area of each tiles exceediing 0.18 Sqm but not exceeding 0.38 Sqm, each in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified

All as per item No 19 here-in-before but cut to required size and fixed on wall daddo/skirting etc .

Non skid joint free ceramic coloured tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.06 sqm but n exc 0.11sqm, in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match the tiles complete all as specified

Glazed ceramic colour tiles in vertical surfaces 600 x 300 x 7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified

15 mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes complete all as specified.

10 mm thick backing coat in CM 1:4 on brick or concrete surfaces for fixing of tiles as in daddo/skirtings complete all as specified

Pressed steel frames for doors with one or more rebates incl necessary fixing lugs, hinges, size of frame 105 x 60 mm complete all as specified

Pressed steel frames for doors with one or more rebates incl necessary fixing lugs, hinges, size of frame 125 x 60 mm complete all as specified

35 mm thick factory made second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., divided in to squares with plain, chamfered or rounded mitred and rebated sash bars any numbers complete incl wooden beading n exc 3 Sqcm all as specified

35 mm thick factory made second class hard wood Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified. Second class hard wood Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified.

18/19 mm thick preliminated particle board Exterior grade preliminated one side with decorative choice laminated & other side balancing white laminated fixed with screw to timber frame work as in palmet, almirah, Kitchen Cupboard etc complete all as sepcifeid.

Fiber glass reinforcedment plastic (FRP) door frames of three legged of cross section 90mm x45mm having single rebete 32x15 mm to recive shutter of30mm thickness . The laminated door frame moulded with fire retardent grade unsaturated polister resin & chopped mat door frame laminate of 2mm thick filled suitable wooden block in all three legs. the shall be covered with fiber glass from all side mild steel stay shall be provided at the bottam to steady the frame complete all as specified

30mm thick Fiber glass reinforcedment plastic (FRP) paneled door shutter made with fire retardent grade unsaturated polister resin moulded 3mm thick FRP laminated for forminghaallow rails and style with wooden frames and suitable blocksof seasiond wood inside at required places for fixing of fitting cast monolithically with 5mm thick FRP laminated for panels complete all as specified

Aluminium alloy wire cloth. 0.45 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with aluminium wire staples complete all as specified

4 mm thick Figured glass, pin headed type and glazing in squares not exceeding 0.5 Sqm in each pane complete all as specified

4 mm thick Sheet glass, ordinary quality and glazing in squares not exceeding 0.5 Sqm in each pane complete all as specified

Cutting holes in brick work built in cement mortar for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement mortar 1:2:4 Type B-1 as required n exc half brick complete all as specified

100 mm long medium weight, cold rolled mild steel Butt hinges complete all as specified

100 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified

100 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified

150 mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified

150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified

300 mm long brass sliding door bolt with sand or die cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolt and fixed complete all as specified

Floor door stopper of Aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor, Overall length of cover plate 150 mm complete all as specified

32 mm dia PVC drapery rods including decorative type end caps, coupling and bracket at both ends complete all as specified

Precast cement concrete masonry type C4 as per IS-2185 Part-I 2005 with solid blocks having minimum average compressive strength of 4 N/Sqmm and minimum strength of individual unit is 3.2N/Sqmm exc 10cm in width and setting in CM 1:4 all as specified and as directed.

75 mm thick PCC (1:3:6) type C2 using 20mm graded stone aggregate as in plinth protection/hard standing etc complete all as specified finished smooth and even without using extra cement

Forming Contration (Dummy) joints 65 mm deep x 10 mm wide, filled with sealing compound grade 'A' complete all as specified

Cutting/Chipping the spalling concrete surface of column, beams, slabs, chajjas, cantilever etc trimming, cleaning the surface to receive guniting/ plastering all as specified.

Applying epoxy treatment with Nitobond AR of Fosroc chemical or equivalent of Dr Fixit or equivalent for bonding old demolished concrete surfaces and guniting including application of one coat of Nitozinc primer to the exposed reinforcement wherever required complete all as specified and directed.

Pressure guniting averaging 20mm thick in CM 1:3 to soffits of slabs, chajjas/parapets by applying chemical prior to gunniting incl providing double scaffolding as reqd and removal of same after use complete all as specified and directed.

Rendering 15 mm thick on brick masonry wall surfaces other than fair faces of brick work in cement mortar 1:6 with finished smooth and even without using extra cement complete all as specified.

Rendering in two coats 8 mm thick in CM 1:4 uing WPC over 12mm thick in CM 1:6 on Brick masonry wall surfaces other than fair faces of brick work finished smooth and even mixed with water proofing compound @ 3% by the weight of cement complete all as specified. Note :- WPC will be measured and paid separately.

Rendering 5 mm thick on concrete ceiling surfaces in cement mortar 1:3 and finished smooth and even without using extra cement complete all as specified.

Supply only integral water proofing compound @2Kg by the weight of cement (ISI marked) of approved make complete all as specified

Injecting chemical emulsion Anti Termite Treatment of soil under existing floors using chemical emulsion at the rate of One liter per hole, 300 mm apart including drilling and plugging 12 mm dia., holes with cement mortar 1:2 to match the existing floors complete all as specified

Injecting chemical emulsion for post construction Anti Termite Treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) at the rate of 0.50 litres per hole by drilling 6 mm dia., holes at a down ward angle of 45 degree at 150 mm centre to centre and sealing the same to match with the existing finish complete all as specified

Injecting chemical emulsion for post constructional anti-termite Treatment along the external/internal wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling 12mm dia upto 300mm deep and 300mm centre to centre and plugging holes in CM 1:2 complete all as specified

Cutting chases, for water tubing or concealed , etc, and making good to facings where required and plastering in cement mortar (1:3) cutting not exceeding 10cm girth in brick/stone walls.

Rotational moulded polyethylene water storage tanks of capacity 500 litres (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified

20mm dia Ball valves high pressure PTMT with epoxy coated aluminium rod &bhigh density plastic ball screwed for iron pipe ( min weight 210gm ), fixed in repair complete all as specified

Taking up or down 15 mm bore steel tubing and connections complete all as specified

Taking up or down 20 mm bore steel tubing and connections complete all as specified

15mm bore medium grade galvanished tube with all fitting & fixed complete to walls or ceiling & laid in floors complete all as specified

20 mm bore medium grade galvanished tube with all fitting & fixed complete to walls or ceiling & laid in floors complete all as specified

20 mm dia Gun Metal, globe or Gate Valve with Iron wheel head Screwed both ends for Iron Pipe and fixed in repairs.

15 mm dia Gun Metal, globe or Gate Valve with Iron wheel head Screwed both ends for Iron Pipe and fixed in repairs.

15mm Bib Taps with wall flange of chromium plated fancy type long shank screwed for Iron Pipe or for brass ferrule of make Cera, Cat No QT F2006151 or equivalent in other makes as specified complete all as specified, fixed in repairs

Two way bib taps with hand faucet with 1.2m brass flexible tube and wall hook mounted type cromium plated for EWC complete all as specified

Stop valve fancy type, brass chromium plated with long shank and cup (concealed type) 15 mm bore screwed down high pressure with lever handle screwed both ends for iron pipe or for unions complete all as specified. Make: Cera Cat No. Exposed part of stop cock consisting sleeve, lever and flange QT F2006351 & concealed part QT F4050102 or equivalent in other makes as specified

Fancy type chromium plated 15 mm bore angle Stop valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions of make Cera, Cat No QT F2006101 or equivalent in other makes as specified complete all as specified, fixed in repairs.

Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long, fixed in repair

Brass chromium plated overhead shower rose 120 mm dia with 3 flow with swivel joint, including shower arm, fixing to steel pipe or union including taking down old shower rose complete all as directed and specified by E-in- Charge. Make: Cera shower rose F7020305 shower arm F7040104 or equivalent in other makes as specified

15 mm bore pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe of make Cera, Cat No QT F2006101 or equivalent in other makes as specified, fixed in repair

Vitreous Ware wash down water closet (Pedestal), white (EWC), fixed in repairs complete all as specified

Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hing device, fixed in repair

PVC Low level flushing cistren 10 Ltr capacety including all itting such as flush pipe brackets Complete all as specified.

Vitreous China Ware Wash hand basin white, flat back, 550x400 mm size type in repairs including cutting for and pinning ends of brackets or erecting stand, fixed in repairs

PVC connection of 15 mm bore and 450 mm long with PTMT checknuts etc complete as specified, fixed in repairs

PVC (SWR) multi floor trap diameter of outlet 75 mm with grating including jointing with solvent cement complete all as specified

Brass Chromium plated tubular towel rail, 20 mm dia., D Type, 60 cm long between flanges, fixed in repairs

Sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, incl bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mmX460mm bowl size 410mmX330mmX160mm complete all as specified, fixed in repairs.

40 mm low densiy polyethylene pipes (LDP) of pressure rating 6 kg/cm2 laid in floor complete all as specified.

PVC (SWR) pipes single socketed in any length with rubbering joints fixed to walls 110mm bore complete all as specified

PVC (SWR) junction single ,( single T) equal or unequal fixed to walls 110mm bore complete all as specified

PVC (SWR) bends any radius 110mm bore with access door complete all as specified

PVC(SWR) vent cowl 110mm bore complete all as specified

75mm dia PVC floor trap with grating incl jointing with solvent cement complete all as specified

75 mm bore PVC (SWR) bends of any radius with access door complete all as specified

75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall complete all as specified

75 mm bore PVC (SWR) branch pipes single socket (double'Y') equal or unequal with eccess door complete all as specified

Preparation of new wall surfaces and applying two coats of oil bound distamper emulsion over a coat of primer over 3 mm thick wall care putty complete all as specified

Complete removal of existing treatment from wall surfaces and applying two coats of oil bound distamper emulsion over a coat of primer over 3 mm thick wall care putty complete all as specified

Preparing newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified

Complete removal of existing treatment of old treated ceiling surfaces of existing and applying two coat of white wash including preparation of old plastered surface complete all as specified

Two coats of synthetic enamelled paint over coat of pink primer on wooden surfaces over 10cm width or girth including preparation on new surfaces.

One coat of synthetic enamelled paint on old decorated wooden surfaces over 10cm width or girth including preparation complete all as specified

Preparation of new steel surfaces and applying two coats of sythetic enamel paint over a coat of red oxide complete all as specified

Preparation of old steel surfaces and applying one coats of synthetic enmal paint exc 10cm width or girth complete all as specified

Preparation of newly plastered surfaces and applying two coats of antifungal exterior coating emulsion paint over a coat of suitable primer etc complete all as specified

Preparation of old painted surfaces by removing the existing treatment completely and applying two coats of Antifungal exterior emulsion paint over a coat of primer complete all as specified

Dismantling of AC cement (corrugated, semi corrugated,etc)sheets in roof covering.

Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified.

Mild steel TMT 6 mm to 8 mm dia., cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified.

Use and waste fair finished flat form work to sides and soffits of floor or roof beams, lintels, cantilevers, shelves including supports etc. complete all as specified.

Precast cement concrete masonry type C4 as per IS-2185 Part-I 2005 with solid blocks having minimum average compressive strength of 4 N/Sqmm and minimum strength of individual unit is 3.2N/Sqmm 10cm in width and setting in CM 1:4 all as specified and as directed

Powder coated anodised aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified including powder coating (Minimum thicknesss of powder coating 50 micron) complete all as specified.

Powder coated anodised aluminium window and ventilator shutter, side hung type without sash, aluminium sections weighing 0.55kg/m incl necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no) hinges type B-21 100mm long(2 no) suitable handle (1 no) complete all as specified. Note : Glazing and gauzing shall be measured and paid separately.

Powder coated aluminium anodised DECO grill 10mm thick DG 104 not less than 3.97Kg/Sqm fixed with necessary H/F/H channel etc complete all as specified and directed.(DECO grill fixed with windows with all fittings complete all as specified and directed

15 mm thick screed bed or bedding layer in cement mortar 1:4,for laying floor finishes complete all as specified

Granite 18-20 mm thick (of any type) work (table rubbed and polished) in steps, cooking platforms, window cills, jambs, risers etc and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade complete all as specified.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified.

Plain mild steel wire 4mm dia, galvanised class 3, in clothing line including straining and fixing to wood, concrete or steel posts and/or to straining bolts, including securing with and provision of galvanised iron tying wire, galvanised iron staples or steel pins, etc. as directed (each line of wire to be measured) complete all as specified.

Mild steel nuts and bolts 20 mm dia exc 30 cm long provided with hole in each bolt for tightning of wire. Made with hexagonal or square head each screwed end to be fitted with washers complete all as specified.

Rolled mild steel in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe 290 Gde E-165 complete all as specified.

ROAD/PATH/CULVERT

Demolition of un reinforced concretein ground floors and Pavings not exc 15 cm thick (below or above ground level ) complete all as specified and directed

75 mm thick, PCC 1:4:8, Type D-2, using 40mm graded stone aggregate as in sub base, surface finished fair and even complete all as specified

Sand filling under floor finishes 40mm thick(compacted thickness) including watering and consolidation complete all as specified

Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade with grey cement and pigment complete all as specified

PCC 1:2:4, type B1 (20mm graded aggregate) as in coping, apex stone, kerb stone, all around the interlocking paver block area all as specified

SEWAGE DISPOSAL

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in hard/ dense soil complete all as specified.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soils complete all as specified.

Removing Excavated soil exceeding 50 m but not exceeding 250 Mtr and depositing where directed at a level not exceeding 1.5 M above the starting point complete all as specified.

150 mm dia Reinforced concrete pipes class NP2 laid and jointed in trenches complete all as specified

PCC 1:3:6 type C2 (using 40 mm graded granite stone aggregate) in concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for pipes of 150mm bore complete all as specified

AREA DRAINAGE

10mm thick plaster in cement mortar (1:4) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified

Cement concrete (1:4:8) type D2 (using 40mm graded stone aggregate) in foundations, filling and mass-concrete complete all as specified

Extra for forming fair finished drain or channel 45 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped end etc complete all as specified

FENCING/GATE

Dismantling fencing wire mesh any type etc complete all as specified

Dismantling post or struts (wood, steel or RCC) any section, including taking out embedded portion in concrete and making good the disturbed ground complete all as specified

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning,filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, in hard and dense soil complete all as specified

Plain Cement Concrete Type C2 1:3:6 (using 40mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified

10mm dia MS bars as stiffners for the chainlink fencing complete all as specified

Supply only chain link MS galvanised fencing, any size or type complete all as specified

Fixing only chain link fencing including line wire lapped, wired and laid in position, including closing after filling welding fixing angle iron etc complete all as specified

Mild steel screw bolts of 10mm dia(machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm but not exc 10 cm long complete all as specified

Rendering 15 mm thick on brick masonry wall surfaces other than fair faces of brick work in cement mortar 1:6 with finished smooth and even without using extra cement complete all as specified

Mild steel work in posts and struts in fencing and FI fiilets for securing fencing cut to shape as directed, including all necessary drilling, bolting or riveting etc , and similar work confirming to Fe 290 GdeE-165 complete all as specified

Mild steel work in framed and hung gates, including Pintle hinges, stops, hand made sliding bolts etc and similar work confirming to Fe 290 GdeE-165 complete all as specified

INTERNAL ELECTRIC SUPPLY

Taking , down carefully copper / aluminium point wiring ( Light ,Fan , socket or power) complete (fittings , switches , celling roses, pendants , regulators, sockets , DB,s) etc all as specified and directed by Engr -in - charge.

Taking down carefully U/S Main switch and DB's incl wooden board, and removing from site incl making good disturbed surfaces of wall all as complete as specified and as directed.

Point wiring complete as specification with 1100 V grade with 1.5 Sq mm single core PVC insulated unsheathed cable ,copper conductor multistranded passing through including concealed PVC conduit and accessories including cutting chases in and making good the surface with GI sunken box and logic modular top cover/ white plate of suitable as required at site with pvc insulated unsheathed stranded copper of size 1.5 sq mm earth wire connected to common earth dully as specified for one light point / bell point /fan point contrlled by one switch. all as specified

All as per item No 146 here-in-before but One light point controlled by 2 Nos, 2 Way switches 5/6 Amps. all as specified

All as per item No 146 here-in-before but 5 amps switch socket in same board all as specified

All as per item No 146 here-in-before but 5 amps switch socket independent board all as specified

All as per item No 146 here-in-before but 15 amps switch socket independent board One 3 pin socket outlet,15 Amps, independent. With cable 2.5 sq. mm size all as specified

Modular bell push 6A, 1 Modular of make Legrand, Cat No 675504 or equivalent in other makes all as specified

Modular switch 2 way 6 A, 1 Modular of make Legrand, Cat No 675502 or equivalent in other makes all as specified

Modular switch 1 way 6 Amps,1 module of make Legrand, Cat No 675501 or equivalent in other makes all as specified

Bell Ding Dong AC 230 Volts, single pole / Multi Music type complete all as specified

Modular switch 1 way 16 Amps,1 module of make Legrand, Cat No 675511 or equivalent in other makes all as specified

Modular Socket 6A -2/3 pin combinaed 2 Module of make Legrand, Cat No 675552 or equivalent in other makes all as specified

Modular Socket 16A -2/3 pin combinaed 2 Module of make Legrand, Cat No 675555 or equivalent in other makes all as specified

Ceilling rose surface PVC Polycarbonate isolated body back lite 65 x50mm three terminals complete all as specified

LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified

LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified

Angular lamp holder, PVC/Polycarbonate type with back plate,230V (ISI marked) surface complete with LED lamp 7 watts all as specified.

Wall mounting, decorative light fitting with opal Glass diffuse suitable for B22 base LED Lamp, complete pre wired with LED lamp 9 Watts Make: FLORETINE WL of Havells all as specified

Supply and replace security light /Street light fitting LED 35W , in aluminium pressure die cast housing with toughened glass cover, IP 66 CCT(k) 6000 of make Havells, Cat No ENDURACITYLITEPLATPLUSSL35WLED757SASYBOPC including necessary bracket duly made out of GI pipe of suitable size, 1.5 Mtrs long bent to shape and fix by saddles complete with conncting up by suitable 3 core wire all as specified

Ceiling fan 1200mm sweep copper wound BLDC 5 star rated, with power consumption 26 to 35 watts with remote control, minimum speed 320 RPM, min air delivery 220 m3/min , including fixing of down rod and connecting up complete with and including three core flexible PVC insulated multi stranded copper conductor cable of size 0.5 Sq mm from ceiling rose connector to fan all as specified

300mm sweep mmetal Body Exhaust Fans, Heavy duty AC single phase 230/240 V of size . Make- Havells , Model Turbo Force SP or equivalent in other makes as specified including depositing old existing fan in MES store yard all as specified

Sheet metal enclosures for DB's TPN double door in wall, 4 way,415 Volt with 200 Amps rated Bus bar complete all as specified

Sheet metal enclouser for DB'S in wall / Nitch when MCB's to be used Single pole and neutral, 8 way, Double door 240 Volt with 200 Amps rated Bus bar complete all as specified

MCB SPN 32 AMP 240 V , 50 HZ, 10KA all as specified

MCB TPN 63 Amp, 415 V , 50 HZ, 10KA, all as specified

MCB SP 240 V , 50 HZ, 10KA, Rating 5-32 A all as specified

Sub main wiring along with earth wire with the following size of 2 x 6.0 Sq mm and 1x 4.0 sq. mm earth continuity conductor and connected to earth dolly ,PVC insulated single core multi stranded copper conductor cable drawn into and including concealed PVC conduit and accessories including cutting chasing in and making good the surface of adequate width and length with all accessories and fittings like bends. Crosses etc complete all as specified

Testing commissioning XLPE insulated ,armoured heavy duty electric cables with aluminium conducter 1100 volts grade, cross sectional area 25 sq mm 4 core & including taking down existing complete all as specified

HDPE (High density polyethlene pipe) of pressure reting 6 Kg /cm 2 for protection of cable laid in trenches of Size 50 sqmm all as specified

Taking down and refixing the same after repair work an electric meter in poly carbonate body with LCD display in class single phase ISI marked ofrating 10 to 60 Amps as per IS 13779 with optical port and box all as specified

Earthing complete with galvanised steel earth plate electrode 60x60cmx6.0 mm thick, buried directly in ground ( earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron Strip 25x4 mm by means of bolt ,nuts ,check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected or indicated including testing on completion . incl necessary exaction ,earth work ,pvc pit ,RCC cover, funnel with watering pipe 20mm bore light grade ,GI protection pipe15 mm bore light grade all as specified

TV socket out let 1 model Cat N0- 675546 of Make-Legrand or equivalent in other makes as specified

RJ 11 Telephone socket 1 module Cat N0- 675541 or equivalent in other makes as specified

Rigid non-metallic PVC conduit 20 mm dia exclusive of boxes (junction/ terminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hooks etc all as specified

Metal flush boxes concealed for mounting TV /Talephone socket etc including logic modular plates and surronds of suitable size all as specified

Ventilating fan PVC 250 mm sweep 230 Volts AC 50 Hz, 900 RPM, with high efficient motor and PVC self clossing shutters, including connecting up from ceiling rose with 3 core flexible copper cable, PVC sheathed of size 1.5 sqmm, complete all as specified and directed at site all as specified

Raj brothers