REPAIR TO FENCING, GATES, DRAIN, FOOTHPATH AND HARDSTANDING AT MIL STN DHRANGADHRA

Amount

Excavation in trenches n.exc 1.50mtr wide and n.exc 1.50mtr in depth for foundation etc or for shaft, wells,cesspits, manholes, piers holes etc not exc 10 sqm on plan and and getting out in hard dense soil all as specified and directed.

Returning filling in,including spreading levelling, watering and well ramming in layers not exe 25 cm in soil completed as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, in hard/dense soil including returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering, and removing surplus soil to a distance n exc 50 m and making good surfaces complete all as specified and directed. (PCC bed blocks in GL or below)

M&L for sand filling under floors/ Interlocking Paver Blocks well compacted complete all as specified and directed.

Removing excavated material soil exc 500m but not exc 1.00Km and depositing where directed at a level n. exc. 1.5 m above the starting point.

M&L for hard core of gauge exc 63mm but n exc 100mm deposited, spread and levelled in layers n exc 15cm thick watered and rolled/rammed to a true surface completed all as specified and directed.

M&L cement concrete (1:4:8) type D-2 using 40mm graded agg as in foundations filling and mass concrete all as specified and directed.

M&L for PCC 1:2:4 type B2 using 40mm graded stone aggregate as in foundation filling/mass concrete.

M&L for cement concrete type B1, 1:2:4 (using 20mm graded stone aggregate) as in surface channels and drains complete all as specified and directed.

M&L for PCC 1:5:10 type E-2 using 40mm graded aggregate for filling into post holes, sunken floors etc. complete as specified and directed.

M&L for cement concrete 1:3:6, type C1 using 20mm graded stone aggregate as in coping, including necessary formwork etc complete.

M&L for providing precast cement conctete 1:2:4, type B1 using 20mm graded stone aggregate as in piers caps post boundary pillars blocks etc setting 1:4 all as specified and directed.

M&L for providing precast concrete wall, louvers and jallies (40 to 45mm thick) type B0 using 12.5 mm graded aggregate, 25mm thick (measured solid) including all mouldings but excluding frame set in cement mortar 1:4 complete all as specified and directged.

M&L for pre cast cement concrete 1:2:4 type B0 using 12.50mm graded stone aggregate as in loures and jallies, 35mm thick (measured solid) including all moulding but excluding frame, set in cement mortar 1:4 complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4 type B-1 using 20mm stone aggregateas in foundation, including rafts, footings, foundation beams, plinth beams, bases for columns etc. basement slabs, underreamed piles and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete 1:2:4 type B-1 using 20mm stone aggregateas in columns, pillars, piers, posts and struts complete all as specified a

M&L for providing precast cement conctete 1:2:4, type B1 using 20mm graded stone aggregate in precast posts, fencing posts with groove to receive Precast concrete wall straining or terminal posts, struts etc. for fencing, average sectional area exc 100 and n.exc 250 sqcm with or without chamfered angles and flat, splayed, rounded or mitred tops fixed complete all as specified and directed.

M&L Granite or trap Stone kerb of roughly squared stones of size 20cm x 30cm, all surfaces hammer dressed so that the maximum depression from a straight edge held against the dressed surface shall not exceed 20mm jointed in cement mortar 1:6 and struck flush completed all as specified and directed.

M&L for walling of random rubble stone masonry, uncoursed, brought upto courses, well bonded, bedded and solidly hearted, built in CM (1:6) complete all as specified and directed.

Extra over stone walling for hammer dressing with maximum depression on face from straight edge held against the dressed surface n. exc 20mm for sand stone and dressing to face stones and dressing of face beds and joints, as specified, of random rubble walling, uncoursed or brought upto courses completed as specified and directed.

M&L 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

Form work to sides of concrete foundations footing bases of coloumn raft and raft beams sides and soffits of plinth beams and similar works vertical or to batter complete all as specified and directed.

M&L for form work to sides of pillars, posts, struts, piers, columns and stanchions and rough finished surfaces of concrete all as specified and directed.

S&F mild steel in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 including one shop coat of red oxide, zinc chrome primer complete all as specified and directed.

S&F, mild steel in flat, round or square bars, in available lengths confirming to Fe-290 Gde E-165 including one shop coat of red oxide, zinc chrome primer complete all as specified and directed.

S&F MS framed work such as grills, gratings etc, with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk way; railings; frame work of water tanks and similar work conforming to Fe 290(Gde E-165) including framed and hung as gates, pintel hinges, stops, hand-made sliding bolts etc complete all as specified and directed.

S&F mild steel screw bolt (machine made) dia of neck 5 to 10mm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exc 5cm long completed all as specified and directed.

M&L for TMT 10mm dia bar and over, as in stiffeners, cut to length, bent to shape required, including cranking, bending, hooking ends, binding with and incluing mild steel wire(annealed) not less than steel wire 0.9mm dia or securing with clips complete all as specified and directed.

S&F, mild steel TMT bar 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc including provision of binding wire complete all as specified and directed.

S&F Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc as directed (each line wire to be measured)

Supply only chain link MS galvanised fencing, any size 50mmx50mm complete all as specified and directed.

M&L for cement concrete 100mm thick, type B-1, 1:2:4 using 40mm graded stone aggregate as in pavement/hard-standing finishing the surface with spike rolling or marking impressions of expended metal, while the concrete is green complete all as secified and directed.

M&L for 60 mm thick machine pressed precast concrete inter-locking paver block with grey cement and pigment any shape and size conforming to IS-15658-2006 M-35 grade complete all as specified and directed.

M&L for 80 mm thick machine pressed precast concrete inter-locking paver block with grey cement and pigment any shape and size conforming to IS-15658-2006 M-40 grade complete all as specified and directed.

M&L for chequered cement concrete tiles 30 cmx30 cmx25 mm thick, with grey cement and pigment, set, jointed and pointed in neat cement slurry over and including 20 mm thick screed bed in cm (1:6) completed all as specified and directed.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Taking down cement plaster on brick or stone wall etc. including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

M&L for rendering 15mm thick cement plaster in cement mortar 1:4 on stone masonary surfaces or surface other than fair face of brick work and finishing the surface even and smooth w/o using extra cement completed as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of white cement primer complete all as specified and directed.

M&L for applying Two coats of 100% Premium acrylic emulsion paint alkali & fungal resistance, dirt resistance exterior paint of required shade and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

M&L for new plastered or un-plastered surfaces of finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied complete all as specified and directed.

M&L for preparation of new steel surface of any description exc. 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L for preparation of old steel surface of any description exc 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new steel surface of any description not exc. 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

M&L Adequate No. of coats painting to kerb stone of pavements and the like exc 10cm wide with road marking paint, white or golden yellow complete all as specified and directed.

M&L for cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate as in bed to drain pipes including packing under, and hunching against the sides of pipe after they are laid and tested for 300mm bore of pipe complete all as specified and directed.

M&L for cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate as in bed to drain pipes including packing under and hunching against the sides of pipe after they are laid and tested for 450mm bore of pipe complete all as specified and directed.

M&L for cement concrete (1:3:6) type C-2 using 40 mm graded stone aggregate as in bed to drain pipes including packing under and hunching against the sides of pipe after they are laid and tested for 600mm bore of pipe complete all as specified and directed.

M&L for 300mm bore reinforced concrete pipe class NP2 laid and jointed complete with collers all as specified and directed.

M&L for 450mm bore reinforced concrete pipe class NP2 laid and jointed complete with collers all as specified and directed.

M&L for 600mm bore reinforced concrete pipe class NP2 laid and jointed complete with collers all as specified and directed.

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc. complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed.

Demolition of plain cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Dismantling barbed wire fencing, wire mesh, any type completed all as specified and directed.

Dismantling posts or struts (wood, steel or RCC) any section, including taking out embedded portion and making good disturbed ground completed all as specified and directed.

Demolition and breaking up drain pipes (salt glazed stoneware, AC or RCC) set in cement mortar for 300mm bore of pipe complete all as specified and directed.

Demolition and breaking up drain pipes (salt glazed stoneware, AC or RCC) set in cement mortar for 450mm bore of pipe complete all as specified and directed.

Demolition and breaking up drain pipes (salt glazed stoneware, AC or RCC) set in cement mortar for 600mm bore of pipe complete all as specified and directed.

Singh Engineer And Contractor

ALBA AC AND REF SERVICES

Shree Builders

Ramdev and Sons

Bhumi Construction