CERTAIN REPAIR TO WATERPROOFING TREATMENT ON ROOF INCLUDING SUNKEN TREATMENT TILING WORKS AND OTHER MISC WORKS UNDER AGE BR 2 GE AF NO 2 JODHPUR AT AF Stn JODHPUR.

Amount

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for (roof padding, flooring above ground floors) including roof treatment and removing from site all as specified and directed by engineerring-in-charge.

M&L for 50 mm thick (average) cement concrete 1:3:6 type C-0 mix (12.5 mm graded stone aggregate) in padding over roof all as specified and directed by engineerring-in-charge.

M&L for 10 mm thick rendering in CM 1:3 over concrete surfaces (Roof) mixed with water proofing compound @ 3% by weight of cement complete all as specified and directed by engineerring-in-charge. NOTE : Water proofing compound shall be measured and paid for separately as “Supply only”

Supply only integral water proofing compound ISI marked .

M&L for applying roof treatment on top of roof with APP modified membrane (minimum 3 mm thick) with non-woven polyster reinforcement/mat (centre core) with thermal insulation with white mineral gravel finish on upper side of membrane laid by torch application method with overlaps 100mm on length side and 100 mm on the width side as per manufacturer’s instructions over and including a coat of approved cold applied bituminous oil based primer (IS- 3384) @ 250 gm/sqm complete all as specified and as directed by Engineer-in-Charge.

Taking down cement plaster, any description on brick, concrete or stone walls or ceiling including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off all as specified and directed by engineerinf-in-charge.

M&L for rendering 15 mm thick in CM 1:4 with using integral water proofing compound on stone masonry surfaces. Note: Integral water proofing compound shall be measured and paid for separately as “Supply only”.

M&L for preparation of new plastered or unplastered surfaces of walls and applying two coats of cement base paint, white or tinted, all as specified and directed by engineerring-in-charge.

Dismantling existing tanks, any capacity, setting aside (or lowering if required) for repairs of roofs and hoisting if required, reconnecting and refixing in position (Repairs to roofs measured separately).

Dismantling existing tanks of any description exc. 250 ltrs and n.exc. 500 ltrs capacity and removing from site all as specified and directed by engineerring-in-charge.

Dismantling existing tanks of any description exc. 500 ltrs and n.exc. 1000 ltrs capacity and removing from site all as specified and directed by engineerring-in-charge.

S&F 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore ball brass valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic plastic ball screwed for iron pipe and fixed all as specified and directed by engineerring-in-charge.. (Minimum weight of ball valve - 210 gms) .

S&F 1000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position all as specified in SSR Part-I, connecting up pipes including 20 mm bore ball brass valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic plastic ball screwed for iron pipe and fixed. (Minimum weight of ball valve - 210 gms)

S&F in repair for 110 mm PVC(SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors,walls height upto 12.0 m complete all as specified and directed.

S&F in repair for 110 mm bore PVC (SWR) bend, suitable for type ‘A’ pipes, any radius all as specified and directed by engineerring-in-charge.

S & F in repairs stack clamps out of 50 mm x 5 mm flat iron and 16mm dia round iron stays including bolts and nuts & securing ends of stays to wall or roof for 160 mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing 15mm bore and connections including cleaning for refixing or removing from site all as specified and directed by engineerring-in-charge.

Taking up or down steel tubing 20mm bore and connections including cleaning for refixing or removing from site all as specified and directed by engineerring-in-charge.

Refixing old steel tubing, 15mm bore, and connections with new or old position (Walls, ceiling, floors, etc.) all as specified and directed by engineerring-in-charge.Note :- Steel tubes obtained from item No. 17above shall be used under this item.

Refixing old steel tubing, 20mm bore, and connections with new or old position (Walls, ceiling, floors, etc.) all as specified and directed by engineerring-in-charge.Note :- Steel tubes obtained from item No. 18 above shall be used under this item.

Supply and laying 15mm bore tubes, galvainzed steel, medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors all as specified and directed.

Supply and laying 20mm bore tubes, galvainzed steel, medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors all as specified and directed.

Dismantling PCC block walling built in any CM all as specified and directed by engineerring-in-charge.

Taking down chowkats or frames exe 1.5 Sqm but n.exc 4 sqm each with shutter (without taking off shutters from the frame) and removing from site complete all as directed.

Dismantling of cast iron or mild steel work of any description not otherwise provided for all as specified and directed by engineerring-in-charge.

M&L PCC 1:3:6 type C1 using 20mm graded stone aggregate as in bed blocks etc for embedding hold fasts complete all as specified and directed by Engineer-in-Charge

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing

Resecuring or easying and adjusting without taking down shutters of any description exe 2.0 sqm each all as specified and directed by engineerring-in-charge.

Dismantling boarding, any description, fixed in any position with nails all as specified and directed by engineerring-in-charge..

S& F for 12 mm thick plywood, grade BWP, type BB, fixed with screws to timber frame work fixed with screws to timber work or other place as builtup furniture cabinet type as specified and as directed,

S&F Aluminium anodised barrel tower bolt of extruded section 150mm size all as specified and directed by engineerring-in-charge.

S&F Butt hinges,heavy weight cold rolled mild steel of size 125mm all as specified and directed by engineerring-in-charge..

S&F extructed aluminium alloy handles, fabricated type,anodised of size 150mm all as specified and directed by engineerring-in-charge..

M&L for rendering 15mm thick in CM 1:6 on stone masonry internal surface including finish even and smooth surfaces using without extra cement all as specified and directed by engineerring-in-charge..

M&L preparing new plastered surfaces and applying two coat Oil bound distemper on walls all as specified and directed by engineerring-in-charge.

Dismantling of floor heart or wall tiling incl cement mortar bedding (but not backing),incl rubbish off premises all as specified and directed by engineerring-in-charge.

Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc. 15 cm thickness (below or above ground level) and removing from site all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate in sub floors all as specified and directed by engineerring-in-charge.

M&L for dark shade coloured Vitrified Ceramic tiles 9-10 mm thick area of each tiles exc 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer in CM 1:6 all as specified and directed by engineerring-in-charge.

All as per item above but on vertical surfaces such as dados, skirtings and risers to steps, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 on stone masonry surfaces all as specified and directed by engineerring-in-charge.

M&L for screed bed or bedding layer of mortar 15 mm thick for laying floor finish with CM 1:6 all as specified and directed by engineerring-in-charge.

S&F, Non skid ceramic tiles coloured 7 to 8mm thick (Square/rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm, in floor, set & jointed in neat cement slurry & pointed in white or coloured cement to match all as specified and directed by engineerring-in-charge.

S&F Glazed ceramic tiles coloured in vertical surface 350x250x7mm/450x350x7 mm thick, set & jointed in neat cement slurry & pointed in white or coloured cement to match over 10mm thick screed bed in CM 1:4 all as specified and directed by engineerring-in-charge..

S&F in repairs drapery rod in any length, high strength MS pipe with corrugated PVC extrusion having outer dia 28 mm with plastic ring of ABS plastic of dia 56 to 58 mm all as directed by Engineer-in-Charge.

S&F in repairs decorative finals ABS plastic in matching colour of steel powder quoted paint of same colour of rod or as directed by Engineer-in-Charge.

S&F in repairs galvanised mild steel wire cloth, 0.56 nominal dia of wire and average width of aperture 1.00 mm and fixed with tinned tacks or galvanised wire staples all as specified and directed by engineerring-in-charge.

S&F in repairs 40 mm dia cupboard knobs of fixed with nut, screw and washer of mild steel, bright finished all as specified and directed by engineerring-in-charge.

S&F continuous (piano) hinges, mild steel, bright finish or electro galvanized width of flaps (when open) 30 mm all as specified and directed by engineerring-in-charge.

Wire brushing and cleaning top surfaces of tarrace or cement concrete includingflashing and junction of parapets all as specified and directed by engineerring-in-charge.

M/L for cement concrete B-0. 1:2:4 (12.5mm graded aggregate) in padding finishing surface of concrete topping even and fair without using extra cement all as specified of average thickness 40 mm in slope of 1:40 over roof all as specified and directed by engineerring-in-charge.

M/L APP modified membrane minium weighting 3 Kg/Sqm with polyster non woven polyster reinforcement ( weight not less than 150 gms/sqm ) shall be laid by torch application method and overlapped by 100 mm in all sides as directed by Engr-in-Charge

M&L for one coat of applied cold bituminous primer @ 1.2 kg/Sqm shall be applied on plastered surfaces including side wall all as specified and directed by engineerring-in-charge.

S&F in repairs, vitreous china wash down water closet pan (pedestal pattern), white, with and including plastic water closet seat, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, PVC valveless, syphonic action type, flushing cistern, low level, 10 litres capacity, white, with inlet, ball valve, float and handle including brackets including PVC flushing pipe, 32 mm dia and fixed complete all as specified and directed by engineerring-in-charge.

S&F in repairs vitreous china squatting pan, ‘Orissa’ pattern, size 580 mm x 440 mm, white with integral foot rests, including PVC 'P' trap, embedded and set in PCC 1:5:10 type E-2 and making good to floor including removing rubbish all as specified and directed by engineerring-in-charge.

S&F in repairs PVC valveless, syphonic action type, flushing cistern, low level, 10 litres capacity, white, with inlet, ball valve, float and handle including brackets all as specified and directed by engineerring-in-charge.

S&F in repairs, 15 mm bore stop valve, fancy type, chromium plated with long shank and cup / (concealed type), screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions all as specified and directed by engineerring-in-charge.

S&F in repairs cast iron floor trap, 75 mm dia of outlet, with grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4) all as specified and directed by engineerring-in-charge..

S&F in repairs cast iron nahani trap, 75 mm dia of outlet, with grating including jointing to waste pipe fixed in cement concrete type B1(1:2:4) all as specified and directed by engineerring-in-charge..

S&F in repairs 75 mm bore cast iron bend (any radius) with duck’s foot or heel rest with oval access door all as specified and directed by engineerring-in-charge..

S&F in repairs cast iron branch pieces, single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches for 75 mm bore pipe all as specified and directed by engineerring-in-charge..

S&F in repairs cast iron branch pieces, single (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches for 100 mm bore pipe all as specified and directed by engineerring-in-charge..

Dismantling of cast iron or reinforced concrete drain pipes of 100 mm internal dia, jointed in cement mortar and taking out of trenches, if required all as specified and directed by engineerring-in-charge..

Dismantling of cast iron or reinforced concrete drain pipes of 75 mm internal dia, jointed in cement mortar and taking out of trenches, if required all as specified and directed by engineerring-in-charge..

S&F 100 mm bore cast iron, sand cast, soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls all as specified and directed by engineerring-in-charge..

S&F in repairs 100 mm bore CI vent cowl all as specified and directed by engineerring-in-charge..

S&F 75 mm bore cast iron, sand cast, soil, waste and vent pipes, in any length with or without ears, with cement joints, fixed to walls all as specified and directed by engineerring-in-charge..

S&F in repairs grating doom 100 mm dia of PTMT (minimum weight 25 gms) all as specified and directed by engineerring-in-charge.

S&F in repair for Pillar cock. all as per directed by Engr-in-Charge Make-Prayag or equivalent, Cat No 7702

S&F in repair 15mm bore pillar tap, cast copper alloy with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed by engineerring-in-charge.

S&F in repairs 15 mm bore bib taps, cast copper alloy, chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule all as specified and directed by engineerring-in-charge..

S&F in repairs, 15 mm bore stop valve, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipe or for unions all as specified and directed by engineerring-in-charge..

S&F in repairs vitreous china wash basin, white, flat back, size 550x400mm including brackets, cutting for and pinning in ends of brackets or erecting stand, brass chromium plated perforated waste coupling/ fittings 32 mm dia with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed and PVC waste pipe of 32mm bore and of suitable length, completeall as specified and directed by engineerring-in-charge.

S&F in repairs brass chromium plated shower rose of 125 mm size with swivel joint including fixing to steel pipe or union all as specified and directed by engineerring-in-charge..

S&F in repairs PVC connection 15 mm size with PTMT nuts of length 450 mm all as specified and directed by engineerring-in-charge..

S&F in repairs 20 mm dia gun metal, globe or gate valve, with iron wheel head, screwed both ends for iron pipe all as specified and directed by engineerring-in-charge..

Welding in repairs exc 2.5 cm & n exc 5 cm in length & thickness of metal n.exc 6 mm all as specified and directed by Engr-in-charge

Resecuring or easing & adjusting without taking down shutters of any description exc. 1 sqm but n. exc. 2 sqm each all as specified and directed by engineerring-in-charge..

S&F in repairs PVC waste pipe of 32 mm bore of suitable length for WHB/urinal/sink, complete all as specified and directed by engineerring-in-charge.

S&F in repairs brass chromium plated health faucet of 15 mm bore completed all as specified and directed by engineerring-in-charge..

S&F in repairs plastic water closet seat cover white or any colour closed padestrial pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device and fixed complete all as specified and directed by engineerring-in-charge.

M&L for repairs to leakage in existing 15 mm bore pipe line by providing elbow/union/socket/tank nipple/nipple up to 200 mm all as directed by Engineer-in-Charge.

S&F in repairs 20 mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe and fixed all as specified and directed by engineerring-in-charge.. (Minimum weight 210 gms.)

S&F in repairs Centre hole basin mixer wall brass CP mixer for mixing hot & cold water screwed down for 15 mm bore iron pipe and fixed.

S&F in repairs PVC flush bend pipe for PVC 10 litre flushing cistern for EWC/IWC all as directed by Engineer-in-Charge.

M&L for repairs to leakage of any type by providing M-Seal all as directed by Engineer-in-Charge.

S&F in repairs PVC jet for EWC of best quality all as specified and directed by engineerring-in-charge..

S&F in repairs aluminium (Die cast) body, door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg and fixed all as specified and directed by engineerring-in-charge..

S&F PVC lid of PVC water tank of 500/1000 litres capacity fixing to existing water tank at any position all as specified and directed by engineerring-in-charge..

S&Fin repair, 3mm thick ACP sheet of panel size (1.2m x 1.2m approx) on mild steel frame (Tabular /ERW section size 50mm x 25 mm) including necessary screws/ fastner/tapes and sealed with silicon and 3mm tap where required all complete as per site requirement and directed by Engr-in-charge. Note :- Quoted rate shall be deemed to be included for work in building structure of any height.

Fixing of scaffloding as required shall be erected for proper execution of work as per site requirement and directed and directed by Engr-in-charge . Note :- Quoted rate shall be deemed to be included for work in building structure of any height.

Supply and fix sound proof panel of size approx (600x600mm) with wooden frame of any size as per site requirement and directed by Engr-in-charge

Removal of existing sound proof panel and frame as per site requirement and directed by Engr-in-Charge.

M&L for providing and injecting chemical emulsion for post construction anti termite treatment along external wall where the apron is not provided using chemical emulsion at therat of 7.5 ltr per sqm of the vertical surface of the sub structure to a depth of 300 mm including excavating channel along the wal and rodding etc complete all as specified and directed by engineerring-in-charge.

M&L for hacking out old broken glass (any thickness, size, quality or description) from metal frame glazed with putty including punching or drilling out old glazing pin/spring, clips and providing new ones all as specified and directed by engineerring-in-charge..

S&F sheet glass 3 mm thick, ordinary quality and glazing with oil putty in square n.exc. 0.5 sqm in each pane all as specified and directed by engineerring-in-charge..

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 sqm but not exceeding 4 sqm each and removing from site.Note-Quoted rate shall be deemed to be include for cutting holes/demolition of PCC blocks etc for taking down chowkats and making good the damaged surfaces in CM 1:3 all as specified and directed by engineerring-in-charge..

S&F rolled mild steel of grade Fe-290 (Grade E-165) in rolled section as in frames for doors/windows, framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc all as specified and directed by engineerring-in-charge..

S&F 35 mm thick factory made, second class hard wood, plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and directed by engineerring-in-charge..

DEV INDUSTRIES

M/s Vishnu Infrastructures

Bansal Enterprises