Creating the PED cabin at office of RAILTEL at Shastri Park New Delhi

S NO DESCRIPTION DSR Amount NDSR Amount

2.00 SANITARY/ PLUMBING WORKS 0.00 2,32,954.80

3.00 ELECTRICAL WORKS 1,52,268.00 0.00

4.00 WI-FI & LAN WORKS Passive Component 33,600.00

5.00 LIGHTING 29,950.00

6.00 FURNITURE 3,79,127.15

Digitally signed by MANISH

SI NO ITEM SPECIFICATION UNIT Quantity RATE DSR AMOUNT

1.00 DEMOLITION

Demolition of brickwork manually/ by mechanical means including stacking of serviceable material

15.7.4 and disposal of unserviceable material within 50 metres lead as per the direction of the engineer in 2.00 cu m 2060.20 4120.40

Dismantling door, windows and clerestory widows (steel or wood) shutter including chowkats,

architrave, holdfasts etc complete and stacking within 50 metres lead

MR Dismentling of Glass Partition 10mm/12mm Thick and stacking within 50 metres lead Sqm 20.00 320 6,400.00

MR Dismantling of carpet & Tile Flooring stacking within 50 metres lead Sqm 30.00 350 10,500.00

TOTAL AMOUNT FOR DEMOLITION WORKS 5,125.90 16,900.00

TOTAL AMOUNT FOR DEMOLITION WORKS 5,125.90 16,900.00

2.00 CEILING WORK

GYPSUM BOARD CEILING: Providing and fixing false ceiling at all height including providing and

fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with

zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of

size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one

flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other

flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of

required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm

running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom

wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to

centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips

made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter

12.45 channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of

ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall

screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel

with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to

a flush finish of tapered and square edges of the board with recommended jointing compound ,

jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of

joint and two coats of primer suitable for board, all as per manufacturer's specification and also

including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of

perimeter channels suitably fixed, all complete as per drawings, specification and direction of the

Engineer in Charge but excluding the cost of painting with

12.5mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with

BIS certification marks)

Digitally signed by MANISH

GYPSUM DESIGN PANEL: Providing and fixing suspended false ceiling- Danoline - : Designpanel

M2F, Size 1200X2400X12.5mm perforation 3X3mm,8.3MM C/C with 7.1 - 9.8% perforation and

NRC upto 0.70: Micro perforation of glass-fibre reinforced gypsum material, which includes providing

and fixing GI perimeter channels The furring should be min. 60 mm wide at the short end joints (if

wood is used; the steel furring can be min. 45 mm). The remaining furring can be 45 mm wide. of

size 0.55 mm. Thk. having one flange of 20 mm and another flange of 30 mm and web of 27 mm

along the perimeter of the ceiling, screw fixed to brick wall/ partition with help of nylon sleeves and

screws, at 610 mm centers. The suspended GI intermediate channels of size 45 mm,0.9mm thk with

two flanges of 15 mm each from the soffit at 900 mm centers with ceiling angle of width 25mm x

10mm x 0.55mm thk fixed to soffit with GI cleat and steel expansion fasteners. Ceiling section of

0.55 mm thk having web of 51.5mm & two flanges of 26mm each with lips of 10.5mm are fixed to the

intermediate channels with help of connecting clips and in direction perpendicular to the intermediate

channel with centers of 333 mm perforated gypboard is then screw fixed to ceiling section with 25

mm dry wall screws at 300 mm centers to G.I. framing in perfect level. Screw fixing is done

mechanically either with screw driver or drilling machine with suitable attachment. Finally the boards

are to be joined and finished so as to have a flush look with jointing compound.

Providing & fixing Danoline Access Panel of size mentioned below having - 1. Outer aluminium

frame - thickness : 1.5mm ( plus 0.2mm thick powder coating) Material : ENAW6063. 2. Inner

Aluminium frame - thickness: 1.5mm (plus 0.2mm thick powder coating) Material : ENAW6063. 3.

Corner fittings, inner frame - material: Hot dipped galvanized steel plate Thickness 2.0mm, with zinc

Coating of 200g. 4. Corner fittings, outer frame - material: Hot dipped galvanized steel plate

Thickness 2.0mm, with zinc Coating of 200g. 5. 12mm plasterboard ( Knauf Brand) Type: moisture

resistant ( MR) in green plasterboard liner. 6. Screw ( self - drilling black phosphate ) - Material: mild

steel C1018 - 1022. 7. Sealing strip, width, thickness - width: 9.0mm, thickness: 4.0mm. 8. Snap

Lock ( spring catch/ catch lock ) - Type of lock: touch latch, Material of lock: plastic ABS, cold rolled

steel Q235. 9. Hinge - Thickness : 4.0mm, Length: 82mm; Material: SS2172 ( cold drawn steel wire

). 10. Powder coating - Color: white, RAL 9010

TOTAL AMOUNT FOR CEILING WORKS 13558.00 168639.00

TOTAL AMOUNT FOR CEILING WORKS 13558.00 168639.00

3.00 PARTITION WORKS

Fabricating and fixing partition frame work consisting of 50mm x 25mm x 1.2mm thick extruded

aluminum box section framework at spacing not exceeding 600mm both ways (horizontal and

vertical). Framework formed using 50mm x 25mm x 1.2mm thick extruded aluminum box section

connected using 50mm X 25mm X 1.2mm thick "L" angle support cleats fixed with 12mm galvanized Job R/O

metal screws. Partition framework to be secured to floor, structural support and nearest structural

member using galvanized metal screws and wooden dowels.

Digitally signed by MANISH

b G.I. FRAME WORK

Supply And Installation Of Gi Frame Work Only As Per Partition Layout Using 'Gypserra' Floor And

Ceiling Channel Of 50mm X 32mm X 32mm X 0.5mm Dimension And "C" Shaped Ceiling Section

Vertically Of 48Mm X 34Mm X 36Mm X 0.5Mm @ 610C/C In Proper Line And Level, Horizontally Job R/O

@750 Mm C/C With Due Supports From Floor / Wall / Roof Slab. (Upto Ceiling Level Area Will Be

c Single sided 12.5mm THICK GYPSUM SKINNING.

Providing & fixing 12.5mm thick taper edge gypsum skinning on existing aluminum frame work using

propriety supplied screws at every 300mm center to center. The gypsum skinning is finished using

proprietary supplied jointing tape & jointing compound as per manufacturer's specification.

d 12MM THICK MDF SKINNING

Providing & fixing 12mm thick MDF skinning on existing aluminum frame work / GI Grame work

using 19mm screws at every 300mm center to center. The ply skinning is finished using approved Job R/O

metal putty & primer as per detail dwg.

5.5mm THICK HDHMR BOARD (BOTH SIDE RAW): Providing and fixing in wall lining, partitions

etc. Confirming to ASTM E-84-2021 class1 BOTH side raw, having even grade low emission, high

moisture resistance, fire resistance, borer, termite & fungus resistance, green material and 90 SQM 504 45360.00

environmental friendly with necessary fixing arrangement and screws etc. , complete as per direction

MR of Engineer-in-Charge

5.5mm thick HDHMR Board

11 mm THICK HDMR BOARD (BOTH SIDE RAW): Providing and fixing 11mm thick HDHMR board

in wall lining, partitions etc. both side raw. Extra density, high moisture resistance, borer, termite &

fungus resistance, green material and environmental friendly with necessary fixing arrangement and

MR screws etc. Complete

11 mm thick HDHMR Board 90 SQM 1079 97110.00

ALUMINIUM FRAME: Providing and fixing partition, frame work in 50x25x1.5mm Aluminium Section

placed at 600mm centre to centre both ways (horizontal & vertical) fastened to floor, ceiling and

horizontal member. The item includes providing and fixing 50mm thick polyester synthetic insulation

MR as insulation of 100 GSM.

LAMINATE PANELLING: Providing & Fixing decorative high pressure laminated sheet of plain /

wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of

adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved

Digitally signed by MANISH

LOUVERED WOODEN WALL PANELS: Providing and fixing ACOUSTIC WALL PANELS. The

MDF wall panels shall be composed of Medium Density Fiber board (MDF) with a minimum density

exceeding 710 kgs/m³, and they shall be covered with PP foil of Renolit, Germany brand/make with a

thickness of 120 microns. The adhesive used for affixing the panels must be PUR (polyurethane)

hotmelt glue, and the design of the panels will be as per the specifications provided by the architect.

The dimensions of the panels are 17-18mm in thickness, 130.5mm in width, and 2745mm in

length.The scope of work includes providing and fixing these MDF wall panels onto a framework

constructed either from MDF or plywood. The framework should have a thickness of 50 mm and a

width ranging from 8mm to 12mm. The installation of the panels can be executed through either the

nail-down method or the pasting method, with the use of a high bonding adhesive suitable for MDF

and plywood, NRC 0.65 upto 1 NRC . The finishing of the MDF wall panels should adhere to the

approved architectural drawings and the directions provided by the Engineer-in-Charge (EIC).

WINDOW BLINDS: Providing & supplying of fabric venetian Window Blinds (Nantucket) as per the

approved sample, consisting of 3" vane size having head rail, rotator rail and bottom rail made of

aluminium alloy 6063-T6 PER ASTM B221 - 85 extruded profile, powder coated and provided in

standard natural white color. The rolling tube should be made up of aluminium alloy from extruded

profile of 34mm dia. The head rail dimensions should be of suitable size according to the length of

head rail and space available and finished with fabric cover matching with the louver fabric. The

cassette should conceal the working mechanism rotary-clutch. (White polycarbonate spring

tempered rotary clutch which raises), lower and tilts the blinds. White polycarbonate limit assemblies

control vane over-rotation, located on either side of individual blinds. The room darkening fabric of

Blind should be of anti-static polyester vanes which have facings between two sheer layers (50 mm 16 SQM 12458

wide) to reduce glare. Sheer layers should be of white 100% knit polyester, the colors, textures and

opacities as approved. The fabric shall be made of spun- bonded 100% polyester fiber (having green

guard certification) treated with soil & dust repellent requiring minimum regular interval cleaning.

GREEN GUARD Gold certified for low-emitting products to maintain Indoor environment. Up to 80%

ultraviolet protection with vanes open and 90% with vanes closed. The shading to be operated by

Easy rise mechanism with a continuous cord loop operating system. All parts, components &

hardware are in approved shade as per direction of Engineer-incharge.

PELMET: Fabricate and install pelmet made of 19mm thick board, up to 300mm high and in line with

external glazing as per details of Architect. Rate to include finishing exposed surfaces of the Pelmet 10 RM 225

MR with 1mm laminate. 2250

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and

manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 100 SQM 156.05 34331

Digitally signed by MANISH

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic

Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying

13.83 additional coats wherever required to achieve even shade and colour

TOTAL AMOUNT FOR PARTITION WORKS 101639.00 686553.00

TOTAL AMOUNT FOR PARTITION WORKS 101639.00 686553.00

WOODEN DOOR FRAMES: Providing wood work in frames of doors, windows, clerestory windows

9.1 and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of

required dia & length (hold fast lugs or dash fastener shall be paid for separately).

9.1.1 Second class teak wood 0.25 cu m 142949.7 142949.7

FLUSH DOOR SHUTTERS: Providing and fixing on all height prefabricated factory made 40mm

thick flush door shutter in existing door frame bounded with BWP type synthetic resin adhesive &

wooden fillers as per IS 848 -1974 shutter should be confirm IS:2202 (part-1) non decorative type

flush door of area up to 1.80 to 2.50 sqm and nothing shall be paid on account of size variation upto

5% plus mimus of make Greenlam, Duro, Century or Equivalent with both side 4mm thick decorative

teak veneering of make sapele/white american oak/vintage teak including fixing on all edges 8mm

MR. thick second class teak wood margin/lipping with 8 mm thick clear vision/frosted glass fitted vertically 4.32 SQM 3838 24947

in flush door shutter of make Saint Gobin, Modi Guard & Hindustan National Glass fixed all-round by

4mm thick second class teak wood margin/molding and size of cut in flush door shutter will be

approx. 200x1800mm or as per approved drawing and one no. of door rubbershutter finished

complete with PU polish all-round i/c SS butt hinges and SS screws all complete as per the direction

of engineer-in-charge. (Note: this item is inclusive of all material, T&P and labour involved and the

work shall be executed as per the approved drawing).

WOODEN LIPPING: Extra for providing lipping with 2nd class teak wood battens 25 mm minimum

depth on all edges of flush door shutters (over all area of door shutter to be measured).

Digitally signed by MANISH

FLUSH DOOR FLOOR MACHINE : Providing Double cylinder Floor Spring D-120 for Wooden

door with Closing Force EN 4 with Maximum door weight 120 Kg. Maximum door width 1250

MR mm.Closing speed : 130° Final closing speed : 15-0°. Hold Open (standard): 90° hold open. Weight 2 SET 15039

of floor spring approx : 6kg, 5,00,000 cycles Tested. approved make and model all complete as per

the direction of Engineer-in-charge. 30078

TOP & BOTTOM STRAP : Providing top and Bottom Strap for wooden doors of approved make and

MR 2 SET 748

model all complete as per the direction of Engineer-in-charge. 1496

FLUSH DOOR DEAD LOCK : Providing and Fixing 160 mm Euro Dead lock with Rose rings for

MR 2 Each 1238

wooden doors of approved make and model all complete as per the direction of Engineer-in-charge.

FLUSH DOOR LOCK CYLINDER : Providing and Fixing 60 mm Eco Pin Cylinder 1CK SS Cylinder

MR One side knob and one side regular key for wooden doors of approved make and model all 2 Each 1137

complete as per the direction of Engineer-in-charge. 2274

FLUSH DOOR HANDLE : Providing 32x840 mm SS 304 H type Handle for wooden doors of

approved make and model all complete as per the direction of Engineer-in-charge. 2 Each 4202

MR Material: Stainless Steel; Finish: Satin Stainless Steel (SSS). 8404

DOOR AND DOOR FRAME WORKS 147573.2 69675

6.00 CABIN FLOORING.

Vitrified Tile Flooring

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the

manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved

11.41.3 make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), SQM 50.00 1,553.45 77672.5

jointing with grey cement slurry @ 3.3 KG/ SQM including grouting the joints with white

cement and matching pigments etc., complete. (Size of Tile 600x600 mm)

TOTAL AMOUNT FOR CABIN FLOORING WORKS 171947.5 0

TOTAL AMOUNT FOR CABIN FLOORING WORKS 171947.5 0

Total for Civil work 4,39,843.60 9,41,767.00

MF @ 0.973 for DSR Items 4,27,967.82

Digitally signed by MANISH

SCHEDULE OF QUANTITIES - SANITARY & PLUMBING WORKS

NO DESCRIPTION UNIT RATE TOTAL AMOUNT

NO DESCRIPTION UNIT RATE TOTAL AMOUNT

Supply, Installation, Testing and Commisioning of SINGLE LEVER

MR 1 CONCEALED BASIN MIXER (WALL MOUNTED) WITH SPOUT EACH 1 16080.00 16080.00

(COMPOSITE ONE PIECE BODY)

Supply, Installation, Testing and Commisioning of TABLE TOP BASIN,

SIZE: 630X460X130 MM

Supply, Installation, Testing and Commisioing of suitable compatible

MR 3 WASTE COUPLING 32MM- FULL THREAD- WITH CERAMIC CAP- EACH 1 2398.00 2398.00

*130MM HEIGHT *65MM CERAMIC CAP

Supply, Installation, Testing and Commisioing of BOTTLE TRAP

MR 4 (WITH INTERNAL PARTITION) 32mm SIZE WITH 300mm & 190mm EACH 1 3284.00 3284.00

LONG WALL CONNECTION PIPES & WALL FLANGE

Supply, Installation, Testing and Commisiong of RIMLESS, BLIND

INSTALLATION WALL HUNG WC WITH UF SOFT CLOSE SLIM

SEAT COVER, HINGES AND ACCESSORIES

SET, SIZE: 375X520X400 MM

Supply, Installation, Testing and Commisiong of PNEUMATIC

Supply, Installation, Testing and Commisiong of ANGULAR STOP

COCK WITH WALL FLANGE

Supply, Installation, Testing and Commisiong of CONCEALED STOP

COCK WITH ADJUSTABLE WITH WALL FLANGE 15mm

Supply, Installation, Testing and Commisiong of HAND SHOWER

(HEALTH FAUCET) WITH 8mm DIA 1.2 METER LONG FLEXIBLE

AND WALL HOOK ALD-CHR-573 or equivalent

Supply, Installation, Testing and Commisiong of PNEUMATIC SINGLE

PIECE SLIM CONCEALED CISTERN BODY WITH INSTALLATION

MR 10 KIT & “S-TYPE” DRAIN PIPE CONNECTION SET FOR WALL HUNG EACH 1 8044.00 8044.00

WC (WITHOUT FLUSH CONTROL PLATE)

Providing and fixing P.V.C. waste pipe for sink or wash basin including

17.28 11 P.V.C. waste fittings complete.

Digitally signed by MANISH

Providing and fixing mirror of superior glass (of approved quality)

17.31 12 complete with 6 mm thick hard board ground fixed to wooden cleats EACH 1 1411.15 1411.15

with C.P. brass screws and washers complete.

Providing and fixing C.P. brass angle valve for basin mixer and gyser

points of approved quality conforming to IS : 8931

15 mm nominal bore 500.35 2001.40

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,

having thermal stability for hot & cold water supply, including all CPVC

plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m

18.8 14 This includes jointing of pipes & fittings with one step CPVC solvent

cement and the cost of cutting chases and making good the same

including testing of joints complete as per direction of Engineer in

Concealed work including cutting chases and making good the walls

18.8.1 15mm nominal outer dia pipes METRE 15 441.15 6617.25

18.8.2 20mm nominal outer dia pipes METRE 15 513.75 7706.25

Providing and fixing C.P. brass long body bib cock of approved quality

18.51 15 conforming to IS standards and weighing not less than 690 gms.

15 mm nominal bore 708.40 708.40

Digitally signed by MANISH

Providing, fixing, jointing and testing in position of ISI marked UV

stabilized UPVC pipes for soil, waste, and vent, Type-B as per IS :

13592 suitable for rubber ring joints, including all neccessary specials

and fittings (confirming to IS:14735) i.e. bends, tees, junctions (with or

without doors), reducers, WC connectors, couplers, expansion joints /

bellows, cowels, clamps, rubber rings, clean outs etc. fixing at wall/

ceiling/ floor level supported by clamp & hangers etc. in concealed /

inside duct / under floor & basement ceiling / external work etc.

including chase cutting as required, excavation and back filling in all

kind of soils, suspended from floor under false ceiling or embedding the

16 pipes laid under floors / building in 75 mm. alround 1:2:4 cement

MR concrete (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm

nominal size) including cost of shuttering for proper completion of the

work, breaking and making good the walls and floors etc. after pipes

have been duly laid and tested. The rubber ring shall confirm to

The Pipes will be supported with threaded G I rods & U clamps with

nuts, washers etc on 50x50x5 mm slotted angle. The cost will include

all support arrangements. The work includes commissioning of all pipes

lines as per drawings and specifications and as directed by engg-in-

charge at site.

a 110 mm dia (Wall Thickness - 3.2 to 3.8 mm) METRE 15.00 536.00 8040.00

b 75 mm dia (Wall Thickness - 3.2 to 3.8 mm) METRE 10.00 416.00 4160.00

Providing, fixing, jointing and testing in position ISI marked (IS:4985)

UPVC pipes of min 6 Kg/ Sqcm rating with fitting for waste pipe from

fixtures to floor trap including reduces, enlarger, socket, couplers,

MR 17 bends, tees etc including fixing at wall/ ceiling level supported by clamp

& hangers etc. cutting holes in wall/ floors/ slabs and making good the

same with cement concrete 1:2:4 complete as required.

Providing & fixing UPVC Floor trap of self cleansing design with

MR 18 stainless steel grating complete in all respects.

Plain Floor Trap (4" Ht) with 50 / 75 outlet and with height raiser EACH 3 536.00 1608.00

Extra for providing & fixing 125 mm dia C.P. grating in place of C.I.

grating over floor traps.

Digitally signed by MANISH

Providing & fixing of SS Floor Cleanout, round or square with rubber

MR seal and flat round cover with screws and other required fitting EACH 3 1001.00 3003.00

20 complete as required.

Providing and fixing stainless steel tray below sewage pipe of size

200x200x200 mm of grade SS304 including all accessories

Supply, Installation, Testing and Commisiong of HIGH FLOW SINGLE

MR 21 LEVER CONCEALED DIVERTOR FOR BATH & SHOWER EACH 1 18938.00 18938.00

Supply, Installation, Testing and Commisiong of SPOUT FOR BUILT

IN BATH/SHOWER MIXER

Supply, Installation, Testing and Commisiong of OVERHEAD

SHOWER 350x350MM ROUND EDGE SQUARE HEAD SINGLE

FLOW (BODY & FACE PLATE STAINLESS STEEL WITH CHROME

PLATED) WITH RUBIT CLEANING SYSTEM

MR 23 Supply, Installation, Testing and Commissioning of 15 litre geyser EACH 1 12004.00 12004.00

Supply, Installation, Testing and Commisiong of SOAP DISH HOLDER

Supply, Installation, Testing and Commisiong of TUMBLER HOLDER

Supply, Installation, Testing and Commisiong of TOWEL RACK

600MM LONG WITH LOWER HANGER

MR Supply, Installation, Testing and Commisiong of ROBE HOOK EACH 1 2045.00 2045.00

26 Supply, Installation, Testing and Commisiong of TOILET ROLL

HOLDER WITH COVER

Supply, Installation, Testing and Commisiong of TOWEL HOLDER

TOTAL 232954.80

Digitally signed by MANISH

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

DSR NO DESCRIPTION

S NO UNIT QUANTITY RATE TOTAL AMOUNT

S NO UNIT QUANTITY RATE TOTAL AMOUNT

A POINT WIRING

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5

sq.mm FRLS PVC insulated copper conductor single core cable in

surface / recessed medium class PVC conduit, with modular switch,

A.1 modular plate, suitable GI box and earthing the point with 1.5 sq.mm.

FRLS PVC insulated copper conductor single core cable etc as

Wiring for group controlled (looped) light point/ fan point/call bell point

(without independent switch etc.) with 1.5 sq.mm FRLS PVC insulated

copper conductor single core cable in surface / recessed PVC conduit,

A.2 and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper

conductor single core cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated

copper conductor single core cable in surface/ recessed medium class

PVC conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper

conductor single core cable for loop earthing as required.

Supplying and fixing following modular switch/ socket on the existing

1.24 modular plate & switch box including connections but excluding modular

plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet Each 10 122.00 1220.00

1.24.5 6 pin 15/16 amp socket outlet Each 10 197.00 1970.00

Supplying and fixing following size/module, GI box along with Modular

1.27 base & cover plate on existing modular metal boxes etc. as required.

Digitally signed by MANISH

B SUBMAIN AND CONTROL WIRING

Wiring for circuit/ submain wiring alongwith earth wire with the following

sizes of FR PVC insulated copper conductor, single core cable in

surface/ recessed medium class PVC conduit as required

1.14.2 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire Metre 150 275.00 41250.00

1.14.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 50 334.00 16700.00

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid

copper conductor PE insulated, shielded with fine tinned copper braid

and protected with PVC sheath in the exisitng surface/recessed steel/

PVC conduit as required

Supplying and fixing of following sizes medium class PVC conduit aong

with accessories in surface/ recess including cutting the wall and

E.12 making good the same incase of recessed conduit as required

Total of Electrical items 152268.00

Digitally signed by MANISH

SCHEDULE OF QUANTITIES - DATA and VOICE WORKS

S NO Description UOM Qty Rate Amount

A. UTP Components for Data

Supply, Fixing & Laying of CAT 6 UTP cable 23 AWG solid copper

(DSR conductors for Connectivity of Hub room to End Point.High Speed

1.53.1) Gigabit Ethernet U/UTP, 250 MHz, Class E, 23 AWG, Unshielded

Supply , Installtion , Testing and Comissioning of I/O port for CAT6

2 MR cable termination at Work Station end. Keystone Unshielded Outlet, Nos. 6 450.00 2700.00

Supply , Installtion , Testing and Comissioning of I/O port for CAT6

3 MR cable termination at Work Station end Redantant . Keystone Nos. 6 450.00 2700.00

Unshielded Outlet, 180DG C6, Yellow

Supply , Installtion , Testing and Comissioning of I/O port for CAT6

4 MR cable termination at Rack Side. Keystone Unshielded Outlet, 180DG Nos. 6 450.00 2700.00

Supply , Installtion , Testing and Comissioning of I/O port for CAT6

5 MR cable termination at Rack Side end Redantant . Keystone Unshielded Nos. 6 450.00 2700.00

Outlet, 180DG C6, Yellow

GRAND TOTAL (A+B+C+D+E) 33600.00

GRAND TOTAL (A+B+C+D+E) 33600.00

Digitally signed by MANISH

SCHEDULE OF QUANTITIES - LIGHTING WORKS

S NO DSR/MR Description Image Unit QTY Rate AMOUNT

Supply, Installation, Testing and Commissioing of Recessed downlightwith

HPE (High-Performance Efficiency) with LED (Light Emitting Diode), system

power: 12 W, Luminous flux of luminaire 1320 lm, 110 LM/W system efficacy,

Colour temperature of 4000 K, Neutral white, CRI > 80, 230V constant current

driver, 70% of luminous flux after 50,000 operating hours; energy-efficient

2 MR LEDs, direct light emission, housing in die-cast aluminium, Polyester powder no 10 1395.00 13950.00

white coloured coat applied over a 5-stage pre-treatment trim, prismatic

diffuser for homogenous light distribution, ZHLS (ZERO HALOGEN LOW

SMOKE) wiring, Electronic control gear,

Protection class II, IP 40, Ø = 175 mm, DA(Ø) = 160 mm, H = 59 mm

Supply, Installation, Testing and Commissioing of Pendant/Recessed

luminaire with LED (Light Emitting Diode), system power 28 W, luminous flux

of luminaire 3080 lm, 110 LM/W system efficacy, direct light emission

CRI>80, colour temperature of 4000K, Neutral white, 230V constant current

driver, 70% of luminous flux after 50,000 operating hours, energy efficient

LEDs, luminaire profile in aluminium, Plastic moulded end caps, Polyester

3 MR powder Aluminium white coloured coat applied over a 5- stage pre-treatment, no 4 4000.00 16000.00

high efficiency glare-free snap fit micro-prismatic diffuser for homogeneous

light distribution, ZHLS (Zero Halogen Low Smoke) internal wiring, integral

Electronic control gear, adjustable suspender,

Protection class I, IP 20, L = 1199 mm, B = 75 mm, H = 90 mm, PL max =

TOTAL 29950.00

Digitally signed by MANISH

Requirement of Suitable Furniture forn PED's Chamber

Sno. Product Name Qty Rate Amount

Providingin place of main table with overall size of table 2100 x 2250 x 750mm. The main table shall be of size 2100 x 1050 x 750mm. The side unit shall

be 1200 x 500 x 750mm. The table is made of 25 mm thick MDF – one side pre-laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane

Topaz pressed on to top. Soft closing access flap within-build power box are provided on work surface for wire management. The ERU top is made of 25 mm

2100 thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The modesty panel is made of 25 mm

Manin thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The understructure is made of 25 mm

Desk thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm

With thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25 mm

ERU thick MDF one side pre-laminate board with 0.4 mm PVC membrane pressed on to top pedestal construction is BOX-BOX-FILE type which uses powder

coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided

for ease of opening. Pedestals are provided with lock for security.

The Back Unit shall be of dimensions 1800 x 500 x 1150mm. It shall be made of 25mm thick MDF – one side pre-laminate board confirming to IS-

14587:1998 with 0.4 mm PVC membrane pressed on to top. The Slide door unit is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and

approved shade edge banded with matching 2 mm thick PVC lipping. Shutters have a soft closing & anti slam mechanism. Handles are provided for ease

of opening. Storage is provided with lock for security.

Digitally signed by MANISH

3 Providing, supplying and placing of High Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is

made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back

foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area.

The chair seat & back size are

HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H)

SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D)

HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per

IS:7888 for 25% compression.

ARMRESTS : The adjustable armrest is designed with the following features

· Up-Down adjustment– 6 steps (7.2 ± 0.5cm range)

· Armrest top is mounted on Armrest structure made of glass filled Nylon.

· Armrest Top is PU moulded over glass filled Nylon insert.

Thrill HB CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: 1 16538 16538

· 360° revolving type.

· 3 position locking with anti shock mechanism.

· Tilt tension adjustment

PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm

PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1

±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors).

TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon.

WIDTH (W): 76.1 CM.

DEPTH (D): 76.1 CM.

HEIGHT (H): 113.5-123.5 CM.

SEAT HEIGHT (SH): 46.0-56.0 CM.

Digitally signed by MANISH

4 Providing, supplying and placing of Mid Back Chair. SEAT/BACK ASSEMBLY: The back is made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat is

made up of 1.5 ±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The back

foam is designed with contoured foam lumbar support. The seat has extra thick foam on front edge to give comfort to popliteal area.

The chair seat & back size are

FULL BACK SIZE 51.5 cm. (W) x 69.0 cm. (H)

SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D)

HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam is moulded with density = 45±2 kg/m3 and hardness load 14 ± 2 kgf as per

IS:7888 for 25% compression.

ARMRESTS : The adjustable armrest is designed with the following features

· Up-Down adjustment– 6 steps (7.2 ± 0.5cm range)

· Armrest top is mounted on Armrest structure made of glass filled Nylon.

· Armrest Top is PU moulded over glass filled Nylon insert.

Thrill CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism is designed with the following features: 3 15140 45419

MB · 360° revolving type.

· 3 position locking with anti shock mechanism.

· Tilt tension adjustment

PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment has an adjustment stroke of 9.5 ± 0.3 cm

PEDESTAL ASSEMBLY : The pedestal is injection moulded in black glass-filled Nylon and fitted with 5 nos. twin wheel castors. The pedestal is 66.1

±0.5cm. pitch-center dia. (76.1 ±1.0cm with castors).

TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon.

WIDTH (W): 76.1 CM.

DEPTH (D): 76.1 CM.

HEIGHT (H): 101.5-111.5 CM.

SEAT HEIGHT (SH): 46.0-56.0 CM.

5 Supplying and Placing in place of 3 seater sofa. The overall dimensions of the sofa shall be 2060W x 905D x 855H. The seat should be made of PU foam

with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with Density 32 ± 2 kg/cu. Seat should be upholstered with fabric or

leatherette. 2) BACK FOAM: The back should be made of PU foam with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density

32±2 kg/cu. mtr, upholstered with fabric or leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be

resistance and termite proof) and pinewood of cross section deviod of major knots and surface defects 6 nos. per seat and 3.8mm dia. zigzag spring

assembly is mounted over understrucrure for cushioning effect. It should be a welded assembly made in Stainless steel tube & plate with plastic endcap.

Company should be ISO-9001, 14001, 45001, 50001, BIFMA, AIOTA and Greenguard certified.

6 Pisa Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing with understructure. It shall be a

Center welded assembly made in SS202 grade having dia. 12+/-0.04. overall dimensions of table shall be Width of table= 112.0 cm, Depth=60.0 cm, height=35.1 1 20026 20026

Table cm.Company should be ISO-9001, 14001, 45001, 50001, BIFMA, AIOTA and Greenguard certified.

Digitally signed by MANISH