Renovation of B - Type 3 units, C - Type 2 units & D - Type 1 unit staff quarters building in Adarsh Nivashi School at Naswadi Ta. Naswadi Dist. Chhotaudepur

Name of Work :- Renovation of B - Type 3 units, C - Type 2 units & D - Type 1 unit

staff quarters building in Adarsh Nivashi School at Naswadi Ta. Naswadi Dist.

BILL OF QUANTITIES

Memorandum showing item of works to be carried out.

It. Description of Item Qty. Unit Rate in Amount

1 Dismentaling tiled of stone floors laid in mortar including stacking of 524.00 Sq.m. 50.28

serviceable materials and disposal of unserviceable materials with

all lead and lift.

2 Demolition and disposal of unserviceable materials with all lead and 37.00 Cum 554.06

lift. (ii) Lime concrete.

3 Dismentaling doors, windows, ventilators etc. (wood or steel) 112.00 No. 196.66

shutters including chowkhats architraves, holdfasts and other

attachment etc. complete and stacking them within all lead and lift.

(i) Not exceeding 3.00 Sq.m. in area.

4 Dismantling of existing plaster of all thickness and removing existing 2848.00 Sq.m. 42.42

dedo with plaster work completely including stacking of the

serviceable materials and disposal of unserviceable materials with

all lead and lift including necessary scaffolding etc. complete as per

instruction of site engineer.

5 Dismantling sanitary fittings like wash basin, W.C. pan Indian and 18.00 No. 424.10

European type, flushing tank etc. including stacking the materials

with all lead and lift.

6 Providing and laying brick work using common burnt clay building 12.00 Cum 4568.40

conventional type bricks having crushing strength not less than

Kg./Sq.cm. in super structure above plinth level upto floor two level

in cement mortar 1:6 (1 cement : 6 coarse sand) for Ground floor

including the cost of all materials and labour charges etc. complete.

7 Providing 10 mm thick cement plaster in single coat on fair side of 387.00 Sq.m. 213.94

brick / concrete walls for interior plastering upto floor two level and

finished even and smooth in cement mortar 1:4 (1 cement : 4 sand)

finishing with a floating coat of neat cement slurry etc. complete for

Ground floor (for Ceiling).

8 Providing 15 mm thick cement plaster in single coat on fair side of 1453.00 Sq.m. 231.38

brick / concrete walls for interior plastering upto floor two level

finished even and smooth in cement mortar 1:4 (1 cement : 4 coarse

sand) including finishing with a floating coat of neat cement slurry

etc. complete as per instruction of site Engineer for Ground floor.

9 Providing 20 mm thick sand faced cement plaster with gutka on 1010.00 Sq.m. 353.98

walls for all heights above ground level consisting of 12mm thick

backing coat of cement mortar 1:3 (1 cement : 3 sand) and 8mm

thick finishing coat of C.M. 1:1 (1 cement : 1 sand) etc. complete

including painting with three coats of water proof acrylic emulsion

paint to give and even shade.

It. Description of Item Qty. Unit Rate in Amount

10 Providing and fixing chicken wire mesh jali between brick work and 96.00 Sq.m. 31.31

R.C.C. work including necessary fixtures and fastening etc.

complete as directed.

11 Providing and laying Ceramic tiles 6mm thick of approved quality in 22.00 Sq.m. 1017.30

flooring treads of steps and landing laid on a bed of 12 mm thick

cement mortar 1:3 (1 cement : 3 coarse sand) finishing with flush

pointing in white cement.

12 Providing and laying ceramic tiles 6mm thick of approved standard 72.00 Sq.m. 1070.50

quality in skirting, risers of steps and dedo laid on 10mm thick

cement plaster 1:3 (1-cement : 3 coarse sand) finishing with flush

pointing in white cement.

13 Providing and laying machine cut free edge machine polished blue 48.00 Sq.m. 688.82

kota stones for shelves in single piece (max. 150cm) 20 mm thick

fixed groove in cement mortar 1:3 and jointed with grey colour

cement slurry including rubbing and polishing etc. complete as

14 Providing and laying polished kotah stone slab flooring over 20mm 57.00 Sq.m. 1019.39

(average) thick base of cement mortar 1:6 (1-cement : 6-coarse

sand) or L.M. 1.1.5 (1-Lime putty :1.5 - coarse sand) laid over and

jointed with grey cement slurry mixed with pigment to match the

shade of slab including rubbing and polishing etc. complete. (A)

15 Providing and laying Vitrified tiles flooring 8mm to 10mm thick using 358.00 Sq.m. 1120.36

size 60 x 60 cm or any approved size in flooring treads of steps and

landings laid on a bed of 12 mm. thick cement mortar 1:3 (1 cement

: 3 coarse sand) finished with flush point in white cement. 24" x 24"

16 Providing and fixing Kitchen Sink with C.I. or M.S. brackets painted 6.00 No. 2326.66

white including cutting holes in walls and making good the same but

excluding fittings (C) Vitreous china sink (i) 600mm x 450mm x

17 Providing and laying China mosaic type water proofing treatment on 307.00 Sq.m. 810.02

terrace including (a) applying neat cement slurry 2.75 Kg./Sqmt. of

cement and mixed with water proofing compound after cleaning the

surface (b) laying cement concrete using brick bats 25mm to

100mm size with 50% of C.M. 1:5 (1 cement : 5 coarse sand)

admixed with water proofing compound over 20mm thick layer of

C.M. 1:5 to required slope including rounding of junction of walls and

slabs (c) After two days of proper curing applying a second coat of

cement slurry (d) Finishing the surface with 20mm thick cement

mortar 1:4 (1 cement : 4 coarse sand) and china mosaic tiling and

finally finishing the surface with trowel with white cement slurry (e)

after finishing the whole terrace shall be flooded with water for a

period of two weeks.

It. Description of Item Qty. Unit Rate in Amount

18 Distempering (two coats) with oil bound distemper of approved 1838.00 Sq.m. 77.30

brand and manufacture and of required shade on wall surfaces to

give an even shade, over and including a priming coat with

distemper primer of approved brand and manufacture after

thoroughly brushing the surface free from mortar dropping and other

foreign matter and also including preparing the surface even and

sand papered smooth.

19 Providing & fixing Aluminium frame colour anodized single shutter 61.00 Sq.m. 5363.10

having colour anodized hollow section frame of size 63.5mm x

mm x 1.2mm (approx. wt. 0.860 Kg/rmt.) with providing

mechanically compressed shutters 35mm thick flush door shutter on

both sides with 1mm lamination on either side with different colour

and S.S. handles of 30cm long & lock as per details etc. complete

as per instruction of site in charge.

20 Providing and fixing window having extruded alluminum colour 35.00 Sq.m. 1713.70

powder coated section frame main outer size 63.50 x 38.10 x

mm (@ Wt 1.094 Kg / Rmt), horizontal two track member size

mm x 31.75 mm x 1.20mm (@ wt.of 0.695 Kg/mt), vertical member

of size 61.85 mm x 31.75mm x 1.30 mm (@ wt.of 0.659 Kg/mt) with

sliding shutters of horizontal member size 40mm x 18mm x 1.29mm

(@ wt. of 0.456 Kg/mt), vertical member of size 40mm x 18mm x

1.29mm (@ wt. of 0.456 Kg/mt. & @ Wt. 0.457 Kg/mt) with 5 mm

thick transparent bronze colour tinted float glass with powder coated

aluminum fittings and fixtures and transparent silicon sealant glass

fixing to frame as per details etc. complete for window.

21 Providing and fixing FRP frame size 100 x 50 mm and 28 mm thick 18.00 Sq.m. 2377.76

FRP depress panel shutter having extra reinforcement on sides and

edges and in gel coat finish. The core of the shutter & frame is to be

filed up with injected fire retardant grade polyurethene foam done in

situ alongwith embedded wooden pieces for stiffening & also taking

hinges & fixtures. The whole FRP frame & shutter is to be water

proof weather proof, termite proof & resistance to mild acid / alkali.

Rates are to be inclusive of S.S. hinges with necessary screws &

alluminium fixtures & fastenings & fastener sleeve.

22 Providing and fixing standard extruded of Aluminium section of size 6.00 Sq.m. 1175.56

63mm x 38.10 mm x 1.2mm (@wt. 0.643 Kg/mt.) with colour

anodized alluminium frame for ventilation with 5 mm thick frosted

glass as details etc. complete for Ventilation as directed by Engineer

23 Providing and laying single piece mirror polishing Granite stone slab 217.00 Sq.m. 2060.40

16mm to 18 mm (average) thick including full moulded round front

and rear edge in jambs & sill laid in 20 mm thick cement mortar 1:6

(1 cement : 6 coarse sand) and jointed with grey cement slurry

including rubbing and polishing etc. complete.

24 Providing and fixing M.S. grills of required pattern to wooden frames 978.00 Kg. 119.18

of windows etc. with M.S. flats at required spacings and frame

alround square or round bars with round headed bolts and nuts or by

screws (A) plain grill including priming coat and two coats of oil

It. Description of Item Qty. Unit Rate in Amount

25 Finishing wall with weather proof exterior emulsion paint on wall 875.00 Sq.m. 122.14

surface (two coats) to give an required shape even shade after

thoroughly brushing the surface to remove all dirt and remains of

loose powdered materials etc. complete.

26 Providing & fixing concealed center point to wall, ceiling and floor 38.00 Rmt. 170.36

I.S.I. mark C.P.V.C. (SDR 13.5) PIPE as approved by Engineer in

charge having National Sanitation Foundation (NSF) seal for potable

water of following dia. nominal bore, tube fitting and clamps

including making good the wall, ceiling and floor etc. complete. (A)

27 Providing & fixing concealed center point to wall, ceiling and floor 200.00 Rmt. 253.82

I.S.I. mark C.P.V.C. (SDR 13.5) PIPE as approved by Engineer in

charge having National Sanitation Foundation (NSF) seal for potable

water of following dia. nominal bore, tube fitting and clamps

including making good the wall, ceiling and floor etc. complete. (C)

28 Providing & fixing concealed center point to wall, ceiling and floor 45.00 Rmt. 660.58

I.S.I. mark C.P.V.C. (SDR 13.5) PIPE as approved by Engineer in

charge having National Sanitation Foundation (NSF) seal for potable

water of following dia. nominal bore, tube fitting and clamps

including making good the wall, ceiling and floor etc. complete. (E)

29 Providing and fixing chromium plated flush cock of approved quality 6.00 No. 263.77

including fixing in pipe line etc. complete. (ii) 25mm dia. as directed

by Engineer in charge.

30 Providing and fixing screw down bib taps of following size (B) brass 30.00 No. 186.83

chromium plated screw down bib tap (i) 15mm dia. as directed by

Engineer in charge.

31 Providing and fixing Gun metal check or non-return fullway wheel 5.00 No. 663.43

valve. (E) 40mm dia. etc. complete as directed.

32 Providing and fixing Gun metal check or non-return fullway wheel 5.00 No. 420.63

valve. (C) 25mm dia. etc. complete as directed.

33 Providing and fixing to wall, ceiling and floor 10.0 Kg.F/Cm2 working 145.00 Rmt. 339.05

pressure polythene pipes of the following outside dia. low density,

complete with special flange compression type fittings, wall clamps

etc. including making good the wall, ceiling and floor. (G) 110mm

34 Providing and fixing to wall, ceiling and floor 10.0 Kg.F/Cm2 working 77.00 Rmt. 280.23

pressure polythene pipes of the following outside dia. low density,

complete with special flange compression type fittings, wall clamps

etc. including making good the wall, ceiling and floor. (F) 75mm dia.

35 Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 18.00 No. 600.23

100mm diameter with jali of the following nominal diameter of self

cleaning design with C.I. screwed down or hinged grating including

the cost of cutting and making good the walls.

It. Description of Item Qty. Unit Rate in Amount

36 Providing and fixing S.W. Gully trap with C.I. grating brick masonry 11.00 No. 1246.92

chamber and water tight C.I. cover with frame of 300 x 300 mm size

(inside) with standard weight (i) square mouth traps (B) 150 mm x

100 mm size P or R type.

37 Providing and fixing water closet squatting pan (Orissa type W.C. 6.00 No. 1373.18

Pan of approved quality) size 580 mm including P trap, flush cock

etc. complete (A) Vitreous china long pattern white color.

38 Providing and fixing Vitreous china flat back wash basin 550 mm x 6.00 No. 2298.76

400mm size of approved brand with single hole for pillar tap with C.I.

or M.S. brackets painted white including cutting holes and making

good the same but including fittings : like 32 mm dia. M.I. fisher

union, C.P. brass waste of 32 mm diameter, pillar tap, capstan head

screw down high pressure with screw, shanks and back nuts of

approved make & stop tap of approved make with connection pipe

etc. complete as directed by Engineer in charge.

39 Providing and fixing in position I.S.I. Mark P.V.C. water tank make of 6000.00 Litre 3.95

approved quality having inside white coating inside including inlet,

outlet flushing and over flow arrangement, ball cock etc. complete

as directed by Engineer in-charge.

40 Constructing brick masonary chamber for under ground C.I. 9.00 No. 2932.93

Inspection chamber and bends with bricks having crushing strength

not less than 35 Kg/cm2 in C.M. 1:5 C.I. cover with frame (light duty)

455mm x 610mm internal dimensions, total weight of cover with

frame to be not less than 38 Kgs. weight of cover 23 Kg. and wt. of

frame 15 Kg) R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse

sand : 4 graded stone aggregate 20 mm. size) foundation concrete

1:5:10 inside plaster 15 mm. thick with cement mortar 1:3 finished

smooth with a floating coat of neat cement on walls & a bed

concrete etc. complete. (i) inside dimension 455mm x 610 mm and

450mm deep for single pipe line.

41 Providing and fixing Godrej type or equivalent as approved by 56.50 Sq.m. 4040.00

Engineer in charge steel cupboard in wall with steel frames and

shutters using 20 gauge M.S. steel sheet including necessary

fixtures, fastening like locks, handles, hinges with approved shade

of spray painting etc. complete as directed by Engineer in charge.

42 Providing Sandwitch type platform of 18 mm thick polished black 10.00 Sq.m. 5027.78

granite at top and 25 mm thick Kota stone slab using cement mortar

1:3 for sandwich and fitting at bottom & edges with waterproof rigid

adhesives including making necessary grooves in walls with Vertical

Kota stone 30 mm x 2 no. sandwitch thick every 60 cm center to

center including all labour materials of approved quality including full

moulded round front edge fixed in wall for partition and jointed with

grey cement slurry including rubbing and polishing etc. complete.

43 Providing and fixing 600mm x 450mm beveled edge glass mirror of 6.00 No. 859.41

superior glass mounted on 6mm the A.C. sheet or plywood sheet

and fixed to wooden plugs with C.P. brass screws and washers.

It. Description of Item Qty. Unit Rate in Amount

44 Painting one coat (excluding priming coat) on previously painted 72.00 Sq.m. 120.22

steel and other metal surface with enamel paint, to give an even

shade including cleaning the of all dirt, dust and other foreign

i.e. Rs. Thirty Six lacs Ninety Four thousand Nine hundred Eleven and Fifty Eight paisa only.

I/We am/are willing to carry out the work @ _______ __ % above/below percent (Should be written

in figures and words) of the estimated rate mentioned above. Amount of my /our tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

1. The Contractor shall exhibit a board with detailed specification and details of work as directed by the Engineer-

In-Charge for which no extra payment shall be made.

2. The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3. GST and Income tax TDS will be deducted at a source while making payments of bills.

4. In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-

10/2017 Cement Consumption/16/C, Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where

there is a change as per actual mix design the cost of difference of cement consumption have been deducted

from the rate of original item at the rate of input rate mentioned in all the tender.

5. Credit for dismantalled materials of amount of Rs.75,000.00 must be recovered from 1st R.A. bill of

Above all items of "Schedule-B" with Item Description, Unit, Rate & Amount have verified by me

and found order.

Deputy Executive Engineer Sr. Divisional Account Officer Executive Engineer

Chhotaudepur (R & B) Sub Division, Chhotaudepur (R & B) Division, Chhotaudepur (R & B) Division,

Chhotaudepur Chhotaudepur Chhotaudepur