Construction of Mamlatdar Office (Type A) At Bayad, Dist:-Arvalli

Construction of Mamlatdar Office (Type A) At Bayad, Dist:- Arvalli

BILL OF QUANTITIES

Percentage Rate Tender

Item Description of Item Quantity Unit Rate In Amount

1 Excavation for foundation upto 1.5 m depth 1496.00 Cumt 122.99

including sorting out and stacking of useful

materials and disposing off the excavated stuff

upto All lift and lead.(A) Loose or soft soil

2 Excavation for foundation for depth from 1.5 m 900.00 Cumt 170.40

to 3.0 m including sorting out and stacking of

useful materials and disposing off the

excavated stuff upto All lift and lead .(B)

Dense or Hard soil

3 Filling in foundation and plinth with sand in 202.00 Cumt 481.80

layers of 20 cm. Thickness including watering

ramming and consolidating etc. comp.

4 Filling available excavated Earth (Excluding 833.00 Cumt 136.92

Rock) in trench plinth side of foundation . in layer

not excluding 20 cm in depth consolidation each

deposited layer by ramming and watering etc.

5 Filling foundation and plinth with murrum or 608.00 Cumt 294.38

selected soil in layer of 20 cm in thickness

including ramming watering and consolidating

6 Applying general insecticide pest control 896.00 Sqmt 80.62

treatment to floors, cupboards etc including

labour material etc. complete. Using Imidacloprid

30.5 SC. As Per 6313 Part -II (0.075%

concentration by mass) is recommended 10.5ml

chemical diluted with 5 liters of water

application 0.5 liters chemical/ sqm of surface is

recommended as per I.S.

7 Providing and laying cement concrete 1:3:6 (1- 39.00 Cumt 307.65

Cement : 3- coarse sand : 6- machine cut stone

aggregates 40 mm nominal size) and curing

complete excluding cost of formwork in (A)

Foundation and Plinth

Item Description of Item Quantity Unit Rate In Amount

8 Providing and laying controlled cement concrete 533.21 Cumt 4394.01

M150 for curing complete including cost of

formwork but excluding the cost of

reinforcement for reinforced concrete work in

9 Providing and laying controlled cement concrete 507.40 Cumt 4642.00

M250 and curing complete including the cost of

formwork and excluding reinforcement for

reinforced concrete work for Foundations,

Footings , Mass concrete

10 Providing and laying controlled cement concrete 45.60 Cumt 7365.83

M250 and curing complete including the cost of

formwork and excluding reinforcement for

reinforced concrete work for Column up to GL

11 Providing and laying controlled cement concrete 244.00 Cumt 6235.74

M250 and curing complete including the cost of

formwork and excluding reinforcement for

reinforced concrete work for Ground/Plinth

12 Providing and laying controlled cement concrete 35.50 Cumt 10304.86

M250 and curing complete including the cost of

formwork and excluding reinforcement for

reinforced concrete work for RCC Wall up to GL

13 Providing and laying controlled cement concrete 186.00 Cumt 5639.23

M200 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

14 Providing and laying controlled cement concrete 116.50 Cumt 7303.88

M200 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

Column Up to First Floor

15 Providing and laying controlled cement concrete 37.00 Cumt 7345.00

M200 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

Second Floor Columns

Item Description of Item Quantity Unit Rate In Amount

16 Providing and laying controlled cement concrete 17.00 Cumt 7386.12

M200 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

Third Floor Columns

17 Providing and laying controlled cement concrete 274.00 Cumt 6183.70

M200 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

Beams for Up to First Floor

18 Providing and laying controlled cement concrete 85.00 Cumt 6224.82

M200 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

Beams for Second Floor

19 Providing and laying controlled cement concrete 15.70 Cumt 6280.07

M200 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

Chhajja Up to First Floor

20 Providing and laying controlled cement concrete 5.00 Cumt 6321.18

M200 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

Chhajja Second Floor

21 Providing and laying controlled cement concrete 22.60 Cumt 7502.28

M200 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

Lintal Up to First Floor

22 Providing and laying controlled cement concrete 11.00 Cumt 7543.40

M200 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

Lintal Second Floor

Item Description of Item Quantity Unit Rate In Amount

23 Providing and laying controlled cement concrete 254.50 Cumt 6958.54

M200 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

Slab Up to First Floor

24 Providing and laying controlled cement concrete 81.00 Cumt 6999.65

M200 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

Slab Second Floor

25 Providing and laying controlled cement concrete 3.00 Cumt 7040.77

M200 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

Slab Third Floor

26 Providing and laying controlled cement concrete 14.00 Cumt 7377.34

M200 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

Stair Up to First Floor

27 Providing and laying controlled cement concrete 30.00 Cumt 10252.85

M200 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

RCC Vertical/Horizontal Wall Up to First Floor

28 Providing and laying controlled cement concrete 22.00 Cumt 10293.96

M200 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

RCC Vertical/Horizontal Wall Second Floor

29 Providing and laying controlled cement concrete 14.00 Cumt 10335.08

M200 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

RCC Vertical/Horizontal Wall Third Floor

Item Description of Item Quantity Unit Rate In Amount

30 Providing and laying controlled cement concrete 19.00 Cumt 6388.43

M200 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

Coping Up to First Floor

31 Providing and laying controlled cement concrete 6.00 Cumt 6429.55

M200 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

Coping Second Floor

32 Providing and laying controlled cement concrete 3.00 Cumt 6470.66

M200 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

Coping Third Floor

33 Providing IS Mark TMT FE-500D bar 239243.00 Kg 77.57

reinforcement for RCC work including bending &

placing in position complete up to All floor Level

34 Providing and fixing 90 cm Height Stainless Steel 54.00 Rmt 4328.86

Railing made from anticorrocive 304 grade S S

pipe of 50 mm dia (16 Gauge) as hand rail with S

S 304 grade Baluster of 40 mm dia (16 Gauge) as

a vertical support fixed in RCC slab at 1.2m c/c

including three horizontal S S pipes of 25 mm

dia (16 Gauge) at eqal distance fixed by

mm dia (16 Gauge) S S pipe with baluster

including accessories as per detailed drawing as

directed etc. complete.

35 Brick work using common burnt clay building 89.70 Cumt 4214.33

bricks having crushing strength not less than

kg./Sq.Cm. in foundation and plinth in Cement

Mortar 1:5. (1- Cement : 5 -fine sand) (B)

Conventional below plinth

36 Brick work using common burnt clay building 406.50 Cumt 4482.57

bricks having crushing strength not less than

kg./Sq.Cm. in foundation and plinth in Cement

Mortar 1:5. (1- Cement : 5 -fine sand) (B)

Conventional Up to First Floor

Item Description of Item Quantity Unit Rate In Amount

37 Brick work using common burnt clay building 140.00 Cumt 4523.06

bricks having crushing strength not less than

kg./Sq.Cm. in foundation and plinth in Cement

Mortar 1:5. (1- Cement : 5 -fine sand) (B)

Conventional Second Floor

38 Brick work using common burnt clay building 30.00 Cumt 4563.55

bricks having crushing strength not less than

kg./Sq.Cm. in foundation and plinth in Cement

Mortar 1:5. (1- Cement : 5 -fine sand) (B)

Conventional Third Floor

39 Half Brick masonry in common brunt clay 1180.00 Sq m 679.55

building bricks having crushing strength not less

than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1-

Cement : 4 -coarse sand ) in foundation and

plinth (B) Conventional in super structure. for Up

40 Half Brick masonry in common brunt clay 480.00 Sq m 685.85

building bricks having crushing strength not less

than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1-

Cement : 4 -coarse sand ) in foundation and

plinth (B) Conventional in super structure. for

41 Providing and fixing 150 mm wide, approved 989.00 Sqmt 295.12

quality chicken wire mesh at junction of brick

work and RCC work or two dissimilar surfaces, at

all heights fixed by nails, rowal plugs or tag

before applying the plaster, including curing,

scaffolding all complete as directed.

42 Providing 15mm thick cement plaster in single 3857.00 Sqmt 215.21

coat on Rough (Similar)side of single or half brick

walls for interior plastering upto floor two level

and finished even and smooth in (ii) Cement

mortar 1:4 (1-cement :4-sand). For Up to First

43 Providing 15mm thick cement plaster in single 1415.00 Sqmt 242.48

coat on Rough (Similar)side of single or half brick

walls for interior plastering upto floor two level

and finished even and smooth in (ii) Cement

mortar 1:4 (1-cement :4-sand). For Second Floor

44 Providing 15mm thick cement plaster in single 338.00 Sqmt 269.75

coat on Rough (Similar)side of single or half brick

walls for interior plastering upto floor two level

and finished even and smooth in (ii) Cement

mortar 1:4 (1-cement :4-sand). For Third Floor

Item Description of Item Quantity Unit Rate In Amount

45 Providing 10 mm. Thick cement plaster in single 1839.67 Sqmt 151.38

coat for plastering on ceiling and soffits of stairs

and finished even and smooth in : (I) Cement

mortar 1:4 (1 cement : 4 sand) smooth finish etc.

complete. Up to First Floor

46 Providing 10 mm. Thick cement plaster in single 589.00 Sqmt 175.03

coat for plastering on ceiling and soffits of stairs

and finished even and smooth in : (I) Cement

mortar 1:4 (1 cement : 4 sand) smooth finish etc.

complete. Second Floor

47 Providing 10 mm. Thick cement plaster in single 14.00 Sqmt 199.27

coat for plastering on ceiling and soffits of stairs

and finished even and smooth in : (I) Cement

mortar 1:4 (1 cement : 4 sand) smooth finish etc.

complete. Third Floor

48 20 mm thick Sand faced cement plaster with 3149.00 Sqmt 363.30

1cmx1cm grooves as suggested by this office

consisting of 12 mm thick backing coat of C.M.

1:3 ( 1 cement : 3 coarse sand ) and 8 mm thick

finishing coat of C.M. 1:1 ( 1 cement : 1 coarse

sand) for all heights as directed etc. complete.

and as per pattern sample aprroved by the

architect or directed engineer in-charge

49 Providing throating or plaster drip and moulding 268.00 Rmt 43.08

to R.C.C. Chhajja.

50 Applying two coats of Acrylic lapy (putty) & two 7987.00 Sqmt 40.59

coats of primer of approved brand and

manufacture on new wall surface to give an even

shade including thoroughly brushing the surface

free from mortar dropping and other foreign

matter and sand papered smooth.

51 Wall painting (two coats) with plastic emulsion 5549.00 Sqmt 82.97

paint of approved brand and manufacture on

undecorated wall surface to give an even shade

including throughly brushing the surface free

from mortar droppings and other foreign matter

and sand papered smooth.

Item Description of Item Quantity Unit Rate In Amount

52 Painting (two coats) with plastic emulsion paint 2438.00 Sqmt 88.47

of approved brand and manufacture on

undecorated ceiling surface to give an even shade

including throughly brushing the surface free

from mortar droppings and other foreign matter

and sand papered smooth.

53 Wall Painting (Two coats) with weather proof 3146.00 Sqmt 83.83

acraylic emulsion paint of approved brand and

manufacture and of required shade on exterior

wall surface to give an even shade over and

including primery coat with Alkaly resistance

primer of approved brand after thoroughly

brushing surface to remove all dust and remains

of loose powdered material etc. copm. for all

54 Forming groove of uniform size from 10 x 10 mm 995.00 Rmt 52.32

and upto 25 x15 mm in plastered surface as per

approved pattern using wooden batten, nailed to

the under layer including removal of wooden

battens, repairs to the edges of plaster panel and

finishing the groove complete as per

specifications and direction of the engineer

55 Providing And filling with good quality cinder 33.00 Cumt 555.40

(steam coal) as directed by engineer in charge in

sunks in layers of 15 cm thick,including

watering,placing ,ramming well etc as directed,

56 Providing Water proofing Treatment on Sunk 167.00 Sqmt 369.96

Slab including cement concrete flooring 1:2:4 (1-

cement : 2-coarse sand : 4-graded stone

aggregate 20mm nominal size) laid in one layer

and finished with a 1:3 (1 cement : 3 Mortar )

floating coat of neat cement average 50mm thick

to Prepare slope including water proofing

chemical etc. Complete for Sunk Slab All Floor.

Item Description of Item Quantity Unit Rate In Amount

57 Providing and laying China mosaic type water 916.00 Sqmt 1125.14

proofing treatment on terrace including cleaning

the surface by wire brush as directed including

applying neat cement slurry @ 2.75 Kg/Sq.smt.

mixed with water proofing compound after

cleaning the surface, laying cement concrete

using brickbats 25 to 100mm size well immersed

in water with 50% of cement mortar 1:5 (1

cement :5 coarse sabd) mixed with water

proofing compound over 20mm thick layers of

cement mortar 1:5 (1 cement :5 sand) to

required slope including rounding of junctions of

walls and slabs and after two days of proper

curing, applying second coat of cement slurry

finishing the surface with rate 20mm thick

cement mortar 1:4 and china mosaic tiles and

finally finishing the surface with white cement

slurry and after finishing the whole terrace shall

be flooded with water for a period of two weeks.

58 Providing Plinth Protection to Building including 233.00 Sqmt 2342.80

excavation in ordinary soil and laying cement

concrete 1:3:6 using stone aggregates of 40mm

nominal size in foundation layer 125 mm thick+

125mm thick sand layer below pre-cast Rubber

Dye inter locking concrete block 60mm thick

with grade of concrete M300 pneumatic

compressed by mechanically pressed and as per

approved design including 75mm Sand layer for

levelling and filling the joint with sand in proper

line and level etc. complete, Including Providing

and fixing pre-cast concrete kerb stone of grey

cement based concrete block 30cm length, 30cm

height and 15cm thick made of M250 grade

concrete as per approved design and including

excavation for fixing in proper line and level,

filling the joint with C:M 1:3 (1cement:3 fine

sand) etc. complete.

Item Description of Item Quantity Unit Rate In Amount

59 Providing and fixing three track Sliding window 40.00 Sqmt 3810.17

+ fixed glass at top having standard extruded

colour anodized aluminum section equivalent to

jindal series C (20 mm) section numbers are :

shutter top -20530 , bottom- 20529, shutter inter

lock - 20531, shutter side (handle) -

frame-bottom with gutter- 21651, frame top &

side – 21650 with 5 mm thick transparent tinted

float glass in shutter as well as fix glass top of

window & Providing and fixing Nylon Mosquito

net with stitching on wall as per window size,

with rubber gasket, air lock strip and finishing

joints with silicon sealant, with standard

extruded colour anodized aluminum coated

fittings as per details etc complete.

60 Providing and fixing fixed window having 61.00 Sqmt 3098.88

standard extruded colour anodized aluminum

section equivalent to jindal frame-bottom with

gutter- 20128, frame top & side – 20147 with

mm thick transparent tinted float glass in shutter

as well as fix glass top of window & Providing

and fixing Nylon Mosquito net with stitching on

wall as per window size , with rubber gasket, air

lock strip and finishing joints with silicon sealant,

with standard extruded colour anodized

aluminum coated fittings as per details etc

complete. fixed window

61 Providing and fixing CASEMENT window having 127.00 Sqmt 5535.00

standard extruded colour anodized aluminum

section equivalent to jindal series B section

numbers are : 20558 , 20559 ,20560, 19391 with

5 mm thick transparent tinted float glass in

shutter as well as fix glass top of window &

Providing and fixing Nylon Mosquito net with

stitching on wall as per window size, with rubber

gasket, air lock strip and finishing joints with

silicon sealant, with standard extruded colour

anodized aluminum coated fittings as per details

Item Description of Item Quantity Unit Rate In Amount

62 Providing & Fixing in position standard extruded 12.00 Sqmt 3398.45

approved colour anodised Aluminum Ventilation

with outer frame 65 x 25 x 1.50 mm Stander Box

Frame @ Wt 0.833 kg/Rmt with 5mm thick fixed

ground glass fixed to alluminium strip blade

fixed or adjestable ventilation & Providing and

fixing Nylon Mosquito net with stitching on wall

as per ventilation size, including all required

materials, fixtures, fastenning, labours and

equipments as per detailed drawing as directed.

For Ventilators

63 Providing and fixing Entrance wooden hollow 42.00 Sqmt 6247.86

two flush door shutter with anodized aluminium

section fram inserted non teakwood , shutter

made from teak wood frame 5cm x 15cm and

no. 5cm x 5cm horizontal rail and vertical rail

cover with both side water proof ply wood of

6mm thick with 1mm thick lamination on both

side including requires teakwood batten of one

coat of primer & two coats of enamel paints on

frame & edges, design of which is to be approved

by the architect ,also added Door shall be

providing with floor spring Pivoted and 30cm

long stainless steel handle and necessary Locking

system of Godrej, fixtures & fastenings etc.

directed by engineer in charge.

64 Providing and fixing 38 mm thick solid core type- 114.00 Sqmt 5876.18

I Single Flush door shuttered having factory

made & stamped I.S 12823 grade-I three layered

resin flushed door having decorative lamination

on both sides & 12 mm thick teak wood beading

fixed around the door including melamine

polished at edges , fixing by Zinc coated hinges

for durable grip including 15cm long stainless

steel handle, Aldrop , stopper and necessary

Locking system, S.S. fixtures & fastenings etc.

directed by engineer in charge. The door from

“NOVAPAN” OR Equivalent company holding

licence for minimum 5 years.

Item Description of Item Quantity Unit Rate In Amount

65 Providing and fixing FRP frame size 100 x 50 mm 31.00 Sqmt 2363.40

and 35 mm thick ( Fiber Glass with PUF Injection

) FRP depress panel Single or Double shutter

having extra reinforcement on sides & edges in

Gel coat finish.The core of the both shutter &

frame is to be filed up with injected fire retradat

grade polyurethene foam done in situ along with

embeded wooden pieces for stiffening & also

taking hinges & fintures.The whole FRP frame &

single or double shutter is to be waterproof,

weatherproof, termite proof & resistance to mild

acid/alkali. Rates are to be inclusive of S.S hinges

with necessary screws & S.S fixtures & fastenings

& fartener sleeve.Colour and Shade approved by

Engineer-In-Charge.

66 P & L 24" x 24" vitrified 8 mm thick tile flooring 1692.00 Sqmt 1466.52

over 20 mm (average) base of cement mortar 1:6

( 1 cement: 6 coarse sand) on new surface or

fixing on existing flooring by adhesive material

including dismentaling of existing flooring and

jointed with color cement slurry including finised

with flush pointing & cleaning the surface etc.

complete (tack 10% DARK shade)

67 P & L 24" x 24" vitrified 8 mm thick tile skirting 78.00 Sqmt 1272.60

over 12 mm (average) base of cement mortar 1:3

( 1 cement: 3 coarse sand) on new surface or

fixing on existing flooring by adhesive material

including dismentaling of existing flooring and

jointed with color cement slurry including finised

with flush pointing & cleaning the surface etc.

complete (tack 10% DARK shade)

68 Providing and laying Porcelene tiles 60 x 60 cm 64.50 Sqmt 1320.07

size 6 mm thick in flooring treads of steps and

landing laid on a bed of 12 mm thick cement

mortar 1:3(1-cement:3-coarse sand)finishing

with flush pointing in white cement etc.

69 Providing and laying antiskid ceramic tiles 30 x 176.50 Sqmt 994.37

30 cm size 6 mm thick in flooring treads of steps

and landing laid on a bed of 12 mm thick cement

mortar 1:3(1-cement:3-coarse sand)finishing

with flush pointing in white cement

Item Description of Item Quantity Unit Rate In Amount

70 Providing and laying primium printed glazed 485.00 Sqmt 1487.88

tiles tiles size 30 x 60 cm 8 mm thick in skirting

risers of steps and dedo on 10 mm thick cement

plaster 1:3 (1-cement:3coarse sand) and jointed

with colour cement slurry etc completed.

71 Providing and laying 10 to 12mm thick ready 75.00 Sqmt 2601.76

made Full body vitrified anti skid Flutes step tiles

of 120x30cm Tread, 120x15cm riser & 60x60cm

Landing with 1cm projecting, nosing half

rounded moulding in tread , laid over 12 mm

(av.) thick bases of cement mortar 1:3 (1-cement

: 3-coarse sand) jointed with grey or colour

cement slurry including rubbing and polishing

incl. Full body vitrified tiles approved by directed

engineer in charge.

72 Providing and fixing frosted finished 600mm x 7.00 Sqmt 6008.49

1200mm glass urinal partition with crystalline

Dhar polish on exposed edges, supported by SS

legs and fitting bracket clamp with cut holes and

silicon grouting, including all accessories and

labor charges directed by the engineering in

charge, etc. complete

73 Providing and fixing mirror polished 18 mm 417.00 Sqmt 2279.57

thick Green Marble stone with full round edge

and polished of approved quality in clading on

sill and around the doors/ windows/ ventilation

with 12 mm thick cement mortor CM (1:4) and

fixing with cement slurry & adhesive including

moulding of exposed edges as directed by

engineering in charge etc. complete.

74 Providing and laying water proofing treatment 107.00 Sqmt 1003.87

by conventional method including cleaning the

slab surface by wire brush as directed including

provding first layer of C.M. 1:4 of 40 mm

thickness mixed with water proofing compound

at rate prescribed by manufacturer, including

putting of brick bats of average thickness 40 mm

Well immerssed in water laid uniformly on first

layer of mortar including applying cement slurry

@ rate of 0.08 bag/sqm. on fixed layer of brick

bats including maintaining necessary slope, in

second layer 40 mm thick C.M 1:4 mixed with

water proofing compound as directed, including

finishing smooth with cement slurry as directed

Item Description of Item Quantity Unit Rate In Amount

75 Providing and fixing M.S Safty Grills having 237.88 Sqmt 2164.19

12mm Solid MS Squre bar Horizontally at every

equal 0.10m C/C distance and 2 no of bar

Vertically at every equal 0.375m C/C distance

Fixing on around (5x40) mm Solid MS Patti

including cutting, welding and fabrication etc;

including one coat of primer of approved quality

and two coats of oil painting as per detail

drawing etc. complete as per directed Engineer in

76 Providing erecting and fixing double coated PVC. 25000.00 Litre 4.09

(ISI) water tank of required capacity each with all

necessary fittings and connection etc. complete

77 Providing laying and jointing in true line and 240.00 Rmt 195.67

level 50mm dia. U.P.V.C. Pipe ( SCH- 40) for cold

water including fittings as approved by Engineer

In Charge. Pipe shall be fixed on the wall with the

help of clamp at every two metre C/C or shall be

concelled as directed including necessary fittings

etc. including testing of pipe and joints and fixing

the same with adhesive solvent, including cost of

78 Providing laying and jointing in true line and 130.00 Rmt 148.12

level 40mm dia. U.P.V.C. Pipe ( SCH- 40) for cold

water including fittings as approved by Engineer

In Charge. Pipe shall be fixed on the wall with the

help of clamp at every two metre C/C or shall be

concelled as directed including necessary fittings

etc. including testing of pipe and joints and fixing

the same with adhesive solvent, including cost of

79 Providing laying and jointing in true line and 260.00 Rmt 91.84

level 25mm dia. U.P.V.C. Pipe ( SCH- 40) for cold

water including fittings as approved by Engineer

In Charge. Pipe shall be fixed on the wall with the

help of clamp at every two metre C/C or shall be

concelled as directed including necessary fittings

etc. including testing of pipe and joints and fixing

the same with adhesive solvent, including cost of

Item Description of Item Quantity Unit Rate In Amount

80 Providing laying and jointing in true line and 110.00 Rmt 72.65

level 15mm dia. U.P.V.C. Pipe ( SCH- 40) for cold

water including fittings as approved by Engineer

In Charge. Pipe shall be fixed on the wall with the

help of clamp at every two metre C/C or shall be

concelled as directed including necessary fittings

etc. including testing of pipe and joints and fixing

the same with adhesive solvent, including cost of

81 Providing, laying and jointing in true line and 120.00 Rmt 834.38

level 160 diametre U.P.V.C (Type B) conforming

to IS 13592-1992 with one end plain and other

end socketed with rubber ring, & fittings

conforming to ISI 14735-1999 of approved make

for drainage system pipe line, pipe shall be

jointed with each other with rubber lubricant,

pipe shall be fixed on wall using of PVC clamp of

the size 160 mm diametre x 210 mm length x

mm heigh at every 2000 mm center to center or

shall be concealed in walls as directed including

necessary fittings such as bends, shoes etc.

including testing of pipes and joints and jointed

with adhesive solvent cement including cost of all

82 Providing, laying and jointing in true line and 144.00 Rmt 876.11

level 110 diametre U.P.V.C (Type B) conforming

to IS 13592-1992 with one end plain and other

end socketed with rubber ring, & fittings

conforming to ISI 14735-1999 of approved make

for drainage system pipe line, pipe shall be

jointed with each other with rubber lubricant,

pipe shall be fixed on wall using of PVC clamp of

the size 110 mm diametre x 149 mm length x

mm heigh at every 2000 mm center to center or

shall be concealed in walls as directed including

necessary fittings such as bends, shoes etc.

including testing of pipes and joints and jointed

with adhesive solvent cement including cost of all

Item Description of Item Quantity Unit Rate In Amount

83 Providing, laying and jointing in true line and 120.00 Rmt 286.84

level 75 mm dia. UPVC SWRType B pipe

conforming to IS 13592-1992 with one end plain

and other end socketed with rubbering and

fitting conforming to ISI 14735-1999 of approved

make for drainage system pipe line, pipe shall be

jointed with each other with rubber lubricant,

pipe shall be fixed on wall using of PVC clamp at

every 2000 mm c/c or shall be conceled in walss

as directed including necessary fittings such as

bends, shoes etc. including testing of pipes and

joints and jointed with adhesive solvent cement

including cost of all materials.

84 Providing and fixing in PVC SWR cowel went 5.00 No 16.16

75mm dia to pipes.(B) 75mm dia.

85 Providing and fixing in PVC SWR cowel went 12.00 No 29.29

110mm dia to pipes.(B) 110mm dia.

86 Providing and fixing PVC SWR Nahni trap IS 15.00 No 586.60

14735 for drain - 100 mm diameter with jali of

the following nominal diameter of self cleansing

design with C.I scread down or hinged grating

including the cost of cutting and making good the

87 Providing and fixing wash down water closet 14.00 No 3890.52

(European type W C pan) with integral P and S

trap including jointing the trap with soil pipe in

cement mortar 1:1 (1 cement five sand) including

providing and fixing plastic seat cover for wash

down WC with CP brass hinges and rubber

buffers back plastic seat with a pair of C I or MS

bracket with complete fitting such as lead valve

siphon 15 mm dia brass ball valve with

polythene float CP brass handle unions and

couplings for connection with inlet out let and

over flow pipes 40 mm dia porcelain enameled

flush bend including cutting holes in walls and

making good the same connection the flush bend

with cistern and closet vitreous china.

88 Provision and fixing water closet squatting orissa 17.00 No 1845.27

type W.C. pan size 580mm integral footrest and

100 mm P or S trap and in cluding 25 mm dia CP

brass flush valve and GI inlet connection etc.

comp. (A) Vitreous china long pattern white or

Item Description of Item Quantity Unit Rate In Amount

89 Providing and fixing stainless steel grab 22 cm x 6.00 No 1492.78

60 cm on door and handicapped toilet including

all fixture and accessary etc completed as per

directed engineer in charge.

90 Providing and fixing ball cock of approved. 4.00 No 189.84

quality as directed.(A) Copper Metal (ii) 50mm

91 Providing and fixing Premium Designer Ceramic 26.00 No 8147.67

Wash Basin Table Top with Slim Rim for

Bathroom (18 x 13 x 5.5 Inch, White Grey, Glossy

Finish) including single hole for pillar tap,

Polyamide braided connection pipe 12mm dia-

450mm length, Waste coupling (Full thread)

32mm Dia, Waste Pipe 32mm dia, 15mm dia

Angle Cock With Wall Flange Chrome Finish,

Pillar Cock High Neck Desk Mounted, and all

accessories such as bolts, nuts required for above

fittings and labor charges etc. completed as per

directed engineer incharge.

92 Providing and fixing 600mm x 450mm bevelled 26.00 No 859.41

edge mirrror of superior glass mounted on 6mm

thick A.C. sheet or plywood sheet and fixing to

wooden pluge with C.P. brass screws and

93 Providing and fixing C.P. brass towel rail comlete 14.00 No 696.90

with C.P. brass brackets fixed to wooden plugs

with C.P. brass scews (B) 600mm x 20mm size.

94 Providing and fixing screw down bib taps of 37.00 No 987.78

following size.(A) Brass screw down bib tap

crome finished polished bright. (i) 15mm dia.

95 Providing and fixing Urinal of approved quality 12.00 No 3530.96

including connection with trap and with integral

longitudinal flush pipe.(A) Squating plate pattern

white earthenware 550mm x 300mm.

96 Providing laying and jointing in true line and 260.00 Rmt 1127.16

level 200mm dia. Form core Pipe for drainage

including fittings as approved by Engineer In

Charge. Pipe shall be fixed on existing structure,

Wall or ground with the help of clamp or shall be

canceled as directed including necessary fittings,

etc. including testing of pipe and joints and fixing

the same with adhesive solvent, including cost of

Item Description of Item Quantity Unit Rate In Amount

97 Providing and fixing S.W. gully trap with C.I. 8.00 No 1246.92

grating brick masonry chamber and water tight

C.I. cover with frame of 300mm x 300mm size

(inside) with standard weight (i) Square mouth

traps (B) 150mm x 100mm size P or R type

98 Constructing brick masonry chamber for 36.00 No 3223.92

underground C.I. Inspection chamber and bends

with briocks having croshing strength not less

than 35Kg. Cm2 in C.M. 1:5 precast RCC cover

455mm x 610mm intenal dimensions with frame

(R.C.C. top slabe with 1:2:4 mix (1-cement :2-

coarse sand :4-graded stone aggregate 20mm

size) foundation concrete 1:5:10 inside plaster

15mm thick with cement mortar 1:3 finished

smooth with a floating coat of neat cement on

walls and bed concrete etc. complete (i) Inside

dimensions 455mmx 610mm and 450mm deep

for single pipe line.

99 Constructing brick masonry chamber for 40.00 No 3933.95

underground C.I. Inspection C.I. Inspection

chamber and bends with briocks having croshing

strength not less than 35Kg. Cm2 in C.M. 1:5

precast RCC cover 500mmx 700mm intenal

dimensions with frame (R.C.C. top slabe with

1:2:4 mix (1-cement :2- coarse sand :4-graded

stone aggregate 20mm size) foundation concrete

1:5:10 inside plaster 15mm thick with cement

mortar 1:3 finished smooth with a floating coat

of neat cement on walls and bed concrete etc.

complete (i) Inside dimensions 500mmx 700mm

and 450mm deep for single pipe line.

100 Extra over items for every additional depth of 20.00 No 242.39

0.1M. of part thereof beyond 450mm depth for

Brick masonry chamber.(i) for 455mm x 610mm

101 Extra over items for every additional depth of 20.00 No 264.86

0.1M. of part thereof beyond 450mm depth for

Brick masonry chamber.(i) for 500mm x 700mm

102 Providing and fixing MS Ladder of required 800.00 Kg 99.99

pattern with MS flats(30x3mm) or round or

square bars (12mm) at required spacing & with

round headed bolts and nuts or screws or

welding including primer coat of approved

quality and two coats of oil paintas as directed

by engineer in charge

Item Description of Item Quantity Unit Rate In Amount

103 Constructing kitchen Platform of 18 mm thick 3.00 Sqmt 6183.22

Polished Black Granite at top and 25 mm thick

Kota stone slab one side polished at bottom with

cementing Materials / adhsives including

makeing necessary grooves in walls with

Vertical sandwich two Kotastone 25 mm support

every 60 cm centre to centre or as required

including all labour material of approved quality

incl. full moulded round front edge granite strip

of one side polished and jointed with grey

cement slurry including rubbing and polishing

etc. complete for all floors

104 Providing and fixing 25 mm thick polished kota 6.00 Sqmt 667.61

stone Shalve with full round edge and double

side polished of any required and fixing with

cement slurry & adhesive including both

exposed edges cut and Smooth Finished as

directed by engineering in charge etc. complete.

105 Providing and fixing Kitchen sink with C.I. or M.S. 1.00 No 5294.42

brackets, painted white including cutting holes in

walls and making good the same but excluding

fittings. (C) Vitreous China Sink.(i) 600mm x

450mm x 150mm size including pillar cock

15mm, M.I fisher union 32mm, C.P Brass waste

32mm , Angle cock 15mm including all laboure

and material charges etc. completed.

106 Providing and fixing kitchen platform trolley 4.00 Sqmt 14213.73

having three drawers of SS (IS 304) of required

size like thali, katleri, perforated, partition,

cupsosar type in kitchen platform having drawer

front side and backside by using 19mm thick all

proof plywood of ISI quality all side laminated

etc. as directed. The size of SS (IS 304) basket of

size 4" to 18" for thali, dish, katleri, perforated,

partition, cupsosar type as directed including

necessary S.S. fittings, handles, nobs, telescopic

channels, etc. as directed

Item Description of Item Quantity Unit Rate In Amount

107 Providing and fixing 0.60 meter wide sand which 8.00 Sqmt 5865.07

type Washbasin platform including supplying

and fixing granite stone of black or equivalant

quality 18 mm thick mirror polished on top and

side posiition and vertical strip at front with

cement slurry & adhesive including moulding of

both exposed edges over 25 mm thick kotah

stone platform fixing in top and sides and

itermediates supports fixing with cement mortar

and adhesive and finishing all material and

labour with necessary fitting complete etc.

108 Providing and fixing in position 300 mm high, 45.00 No 1333.20

150 mm wide English letters made from 1.0 mm

thick stainless steel sheet as directed by Engineer

in charge with all necessary tools & plants etc.

109 Providing and fixing in position 150 mm high, 72.00 No 686.80

English letters made from 1.0 mm thick stainless

steel sheet as directed by Engineer in charge with

all necessary tools & plants etc. complete.

110 Providing & Fixing 114mm wide G.I. Sheets 57.00 Sqmt 7824.47

lovers having weight not less than 490 Gm/m roll

formed to create 84mm wide louver snap fixed

on special shaped GI channel. Fix louvers &

channels shall finished with powder coating of

micron (1) 0.55mm thick sheet.etc. complet as

per detail drawing as directed.

111 Providing and Fixing a set of wall mounted 38 9.00 No 2671.45

mm dia U shaped horizontal stainless steel

collapsible grab bar , 38mm vertical stainless

steel fixed grab rail of grade SS 304 from round

pipe supported and 75 mm dia 8 mm thick SS

304 base flange on wall including anchor

fasteners, nuts, accessories as per detailed

drawing etc. complete as directed by Architect or

Engineer in charge.

112 Providing and fixing MS Z clamp on Wall or 212.00 No 85.85

celling for Pipe Fitting including all type

necessary fittings and accessory etc. completed

as per directed engineer in charge.

113 Charges for making holes from 50mm to 160 mm 30.00 No 858.50

dia in RCC wall, slabs or any other RCC members

or Brick work by diamond core cutting machine

of HILTI or equivalent including disposing the

debris. For all floors .

Item Description of Item Quantity Unit Rate In Amount

114 Providing and fixing coloured self adhesive PU- 72.00 Sqmt 5309.57

Tactile tile, ground surface indicators of

Polyurethane) of size 300mm x 300mm for

guiding/warning to the visually visitors in the

centre/side of the pedestrian/approach pathway

as per specification and guidelines complete in all

respect to the entire satisfaction of in charge.

115 Providing and fixing acrylic multilingual Braille 90.00 No 1964.45

(raised dots) DIRECTIONAL SIGNBOARDS of size

225 x 150mm designed as per accessibility

standards and having 3.5mm thick acrylic base

plate with Upper Case San Serif words made of

white acrylic non glare cut out letters of height

15mm raised not less than 0.8mm above base

plate and the equivalent word written in Hindi

with Devanagari non glare acrylic letters of

height 15mm raised not less than 0.8mm above

base plate and having a non-glare acrylic cut

arrow pointing in the required direction. Each

signboard to be fixed as per manufacturers

specifications on the wall at the approved

location and at a height of 1200mm from FFL

complete as per design / specifications and

guidelines as per the entire satisfaction of the

Engineer-in-charge

116 Providing & Fixing tactile layout plan of size 1.00 Nos 38208.30

900mm x 600mm as approved design, made of

3.0mm thick acrylic non glare base plate and non

glare cut out symbols with Braille on which

individual facility points, like inquiry, reception,

restrooms, medical room / first aid, cafeteria or

breakout area, lounge, meeting room, conference

room etc. present the respective floors with

pictograph wherever needed all in tactile raised

by minimum of 1.0mm to 2mm in various colours

to make it legible for seniors, partial vision

impaired etc. All the facility names should be in

Braille, along with English or Hindi. The entire

block of tactile signs should be mounted on wall

for easy reading. The map to be installed at

specified locations and installed at a height of

800mm from ground level complete in all respect

as per Harmonized guideline & satisfaction of

Engineer in charges.

Item Description of Item Quantity Unit Rate In Amount

117 Providing and fixing of acrylic, non-glare, tactile 1.00 Nos 50298.00

audio pictorial building layout as per the

approved size, design and make, having 3mm

thick acrylic non glare base plate of the approved

colour and non-glare acrylic cut out symbols

raised 3mm above base plate and Grade 2/ Grade

1 Braille to be integral with the sign face and be

raised 0.5mm above base plate. The map to be

installed at the specified location as per

accessibility standards, shall be oriented to the

position of the viewer and to be installed at a

height of 800 mm from the finished ground/

floor level and using the necessary hardware

specified by the manufacturer and to be installed

up to the height of 800 mm from the finished

ground/ floor level and using the necessary

hardware specified by the manufacturer and to

be installed complete as per

design/specifications and guidelines as per the

entire satisfaction of the the Engineer-in-charge

118 Providing & fixing Braile indicator of size 170 45.00 Rmt 951.42

mm x 35mm for handrails of the approved

design and make have braile dots raised 0.5 mm

above base plate to be installed at specific

locations as per direction of engineer in charge

119 Providing and fixing of conspectus tape 50mm 65.00 Rmt 1447.33

width on of treads in staircase including cutting

pasting etc. As per harmonised guidelines

complete in all respect to the entire satisfaction

of engineer in charge.

Item Description of Item Quantity Unit Rate In Amount

120 Providing and Fixing 15 mm thick 300 mm x 300 90.00 Sqmt 1356.43

mm Tactile Warning Tiles (Attention Tiles i.e.

Tactile Warning Surface Indicator {TWSI}) of

Johnsan Endura Tac Button Yellow Plus or

equvqlent make in flooring laid on 20 mm thick

cement mortar 1:6 (1 cement : 6 coarse sand) on

new surface and jointed with cement slurry

including finished with flush pointing & cleaning

the surface for all floors as per detailed drawing

etc. complete as directed by Architect or Engineer

in charge. Thse tiles shall be Anti Skid, Chemical

Resistant, Fade Proof, Frost - Heat & Weather

Proof, High Flexural Strength, Highly Durable,

Stain Resistance . All Tactile Warning Tiles meet

the specific size and dimension standards as

required by ISO/FDIS

121 Excavation for foundation for depth from 3.0 m 26.00 Cumt 183.75

to 5.0 m including sorting out and stacking of

useful materials and disposing off the

excavated stuff upto All lift and lead.(B)

Dense or Hard soil

122 Providing and fixing C.I. Manhole cover 0.60 M. x 1.00 Nos 958.17

0.45M. size having weight not less than 35Kg.

123 P & L 60x45 cm Polished Machine cut Blue Kota 48.00 Sqmt 1066.94

Stone slab flooring over 20 mm (average)thick

base of cement mortar 1:6 (1-cement 6-coarse

sand) or L.M 1:1.5 (1 Lime putty : 1.5 coarse sand

laid over and jointed with grey cement slurry

mixed with pigment to match the shade of slab

including rubbing and polishing etc.complete (A)

124 Providing and fixing rolling shutters of approved 5.00 Sqmt 3554.40

make made of 80 mm wide M.S laths inter-locked

together through heir entire length and jointed

together at the ends by end locks mounted on

specially designed pipe shaft with bracket

plates,guide channels and arrangement for inside

and outside locking with push-pull operation

including the cost of hood cover and sprig

etc.complete(A) Shutters having width below

125 Drilling pilot borehole of size 250/300 mm at 250.00 Rmt 573.68

above site by mud flush direct rotery rig.

126 Reaming of 250/300 mm dia.Pilot borehole to 250.00 Rmt 349.46

size 550 mm dia. Incliding assembling ,lowering

housing ,casing strainerpipers with gravel

packing and clayball packing etc.

Item Description of Item Quantity Unit Rate In Amount

127 Development of cach water bearingzone coming 1.00 Job 27191.22

across the full depth of tubewell by lowering

mm dia.Droplineand 32 mm dia airline for each

water bearing Zone with suitabale capacity air

compressar up to avilability of sand free

128 900 CFM /200 PSI capacity air compressar upto 1.00 Job 27603.30

the availability of sand free discharge for upto

129 Supply of M.S. E.R.W. plain end medium duty pipe 250.00 Rmt 3605.70

confirming to IS 4270/2001 with latest

amendments Of size 250 mm dia (minmum

thicknes of 7.1 mm)

130 Screen Slotting of MS ERW balnce pipe with size 112320.00 slots 0.24

of slot 6.75 cm X 6.35 cm X 3.12 mm for 250 mm

131 Supply of miscellenious bore material suitable to 1.00 Pair 2037.91

250 mm dia pipes as following (A) MS Bore

clamps made from M.S. plate with 3 holes on

either side with nuts & bolts of std make of size

900X100X16 mm flat suitable for 250 mm dia

132 Supply of miscellenious bore material suitable to 1.00 No 1161.62

250 mm dia pipes as following (B) MS Bore Plug

having 100mm height made from M.S. plate with

3 holes at equal distance on circumferrence for

nut-bolts type, locking arrrangement with nuts-

bolts & lock nuts of std make complete from

mm thick M.S. plate suitable for 250mm dia pipe.

133 Supply of miscellenious bore material suitable to 1.00 No 1065.02

250 mm dia pipes as following (C) MS Bail Plug

having length 0.45 mtr from medium class pipe

as per I.S. suitable for 250 mm dia pipe.

134 Supply of miscellenious bore material suitable to 168.00 NO 91.71

250 mm dia pipes as following (D) Steel bent

plate suitable for ERW pipe for 250mm dia

(size:200 X 150X6 mm)

135 Supply of GRAVEL OF selected size 4 mm to 6mm 40.00 Cum 2049.29

136 Electrologging of Pilot bore hole with carting. 1.00 Job 18180.00

137 Geohydrological ground water investigation 1.00 No 14428.86

including vehicle charges for three phase DTH

bore/DR tube well including water sample

testing & chemical analysis

138 Providing, supplying and commissioning ISI 1.00 No 5401.48

mark CI D/F Reflux Valves of following class and

diameter including all taxes, insurance,

transportation, freight charges, octroi, inspection

charges, loading, unloading, conveyance to

departmental stores stacking etc. complete.

Reflux valves PN 1 IS 5312 with ISI mark size:

Item Description of Item Quantity Unit Rate In Amount

139 Providing and laying in trenches galvanised mild 200.00 Rmt 919.80

steel tubes (Midium grade) of the following

nominal bore, and tube fitting (Earthwork in

trenches to be measured and paid for separately

140 Constructing Manhole with R.C.C. top slab in 3.00 No. 11042.74

1:2:4 mix (1-cement :2-coarse sand : 4-graded

stone aggregate 20mm nominal size) foundation

concrete 1:3:6 mix (1-cement : 3- coarse sand :6-

Brick bats 40 + 50mm size) inside plastering

15mm thick with Cement Mortar 1:3 (1-Cement :

3-coarse sand) finished with a floating coat of

neat cement and making channels in cement

concrete 1:2:4 mix (1-Cement :2-Coarse sand :4-

stone aggregate 20mm nominal size) finished

smooth complete including curing and festing (i)

Inside size 900mm x 1200mm and 1.5M. deep

including C.I. cover with frame size 560mm

diameter total weight of cover and frame to be

not less than 128 kgs. (Wt. of cover 64 Kg. and

Wt. of frame 64 Kg.)(A) With 230mm thick walls

of brick msonry using brick having crushing

strength not less than 35Kg. / Sq.cm. in Cement

Mortar 1:5 (1- Cement: 5- Coarse sand) (1) A

type depth 0.90 Metre for 150mm diameter

141 Providing laying (to level or slopes) and jointing 356.00 Rmt. 678.02

reinforced concrete Light duty non-pressure

pipes I.S. class NP2 of the following internal

diameter with collars and butt ends prepared for

collar joints including testing of joints

complete.(D) 300mm

142 Providing and fixing and floor 10.0 Kg. F/Cm2 150.00 Rmt 339.05

working pressure poluthene pipes of the

following outside Dia. Low densidy, complete

with special falnge compression type fittings,

wall clipsetc. including making good the wall

ceiling and floor.(G)110 mm

143 Providing and fixing and floor 10.0 Kg. F/Cm2 20.00 Rmt 696.90

working pressure poluthene pipes of the

following outside Dia. Low densidy, complete

with special falnge compression type fittings,

wall clipsetc. including making good the wall

ceiling and floor.(G)180 mm

Item Description of Item Quantity Unit Rate In Amount

144 Providing junction for rain water juncton 10.00 Nos. 9651.56

chamber of size 0.60x0.60x0.75m with

excavation of size 1.96x1.96 m & 0.15m thick

c.c.1:2:4 bed concrete including brick masonary

wall in CM 1:6 of 0.75m height & 0.23m thick

with 15mm thick cement plaster inside & outside

& 1.06x1.06 RCC (1:2:4) slab of thickness 0.15m

with CRS steel and 0.60mx0.45m cast iron

manhole cover with frame weight not less than

35 kg as per directed by Engineer-in-charge

145 Providing and installation Recharge pit of 1.00 Nos. 109645.60

“RAIWOHA” Make 3 layer RCC Precast Injection

well system of size 1.5 meter Dia. X 3.4 Meter

Height rein forced concrete precast three layer

module with 6” dia x 12” dia. V wire screen of

0.75mm x 1.0 mm Slot size in SS 304 material

and 1.0 meter height with MS Top cover and

required Air vent including all necessary

excavation and transportation at site including

required filter media for the recharge system as

per site requirement.

146 Drilling of min. 250 mm dia. bore hole in all 50.00 Rmt 1138.27

strata including dualover burden strata by

combination DR/DTH rig including lowering

mm dia MS ERW pipes in bore hole and testing

etc.all work as per directed engineer incharge.

147 Supplying slotted PVC pipes of approved quality 50.00 Rmt 555.50

at site of work confirming to IS. 1239/1974

148 Cleaning & maintenance of system Including all 1.00 Nos. 4646.00

Labour and replacing of Filter Media as Required

149 Construction of granular sub-base 150 mm thick 271.26 Cum 1269.57

by providing coarse graded machine crushed B.T.

material satisfying MOST specification of grading

I (B.T. stone aggregate 53 mm to 26.5 mm 35 %,

26.5 to 4.75 mm - 45 % and 2.36 mm below -

% )including spreading in uniform layer with

motor grader on prepared surface, mixing by mix

in place method with rotavator at OMC and

compacting with vibratory roller to achieve the

desired density etc. complete.

Item Description of Item Quantity Unit Rate In Amount

150 Steel work, welded in built up sections framed 8918.00 kg 91.08

work including cutting, hoisting, fixing in

position and applying a priming coat of read lead

paint & two coat oil paint. (A)In beams and joists,

channels angles Tees, flats, with connecting

plates or angle cleats as in main and cross beams.

Hip and jack rafters, purlins conneted to common

rafters and the like..

151 Providing and fixing of Ridge flashing for roof 316.00 Sqmt 867.39

panel shall be made out of 0.5 mm thick pre

coated GI sheet . The Precoated sheet shall be of

minimum 240 mpa steel grade confirming to IS

14246:1995 and shall have zinc coating of

minimum 120 gsm as per IS:277:1992 , 5-7

microns epoxy primer on both side of the sheet

and polyester top coat 15-18 micron. The PPGI

Sheet shall have plastic protective guard film of

minimum 25 microns to avoid scratches during

transportation. The ridge shall be fixed to the

steel members by pop rivet or self drilling/self

stitching fastners @ maximum 450 mm c/c along

length of capping/flashing etc complete .

152 Providing and fixing pre-cast Rubber Dye / steel 670.00 Sqm 706.93

Dye inter locking concrete block 60mm thick

with grade of concrete M300 pnumatic

compressed / vibrated mechanically and as per

approved design Confirming to IS 15658 :

including 35 mm Sand layer for levelling and

filling the joint with sand in proper line and level

as per guidlines of IRC : SP 63-2018 etc. Complete

153 Providing and fixing pre-cast concrete kerb stone 468.00 Rmt 365.44

of gray cement based concrete block 30cm

ength,30cm height and 15cm thick of M250 grade

concret as per approved design and including

excavation for fixing in proper line and

level,filling the joint with C:M 1:3 (1cement:3fine

sand) etc complete.

154 Box cutting the road surface to proper slope and 719.00 Cum. 109.05

camber for making a base for road work

including removing the excavated stuff and

depositing on the road side slope as directed

upto upto All lift and lead..

155 Providing, laying and compacting natural sand & 106.00 Cum. 585.80

gravel[ C.B.R. not less than 20%] below sub base

course including carriage of materials spreading

in uniform layer manually on prepared base and

compacted with vibratory roller to achieve

desired density including all materials, labour

Item Description of Item Quantity Unit Rate In Amount

156 Providing and laying wet mix macadam base 299.00 Cum. 1473.59

course 250 mm thick in two layers using machine

crushed B.T. chips as per required gradation

mixing with required optimum quantity of water,

conveying the mix to site of work, spreading in to

grade and camber with mechanical paver and

consolidation each layer with vibratory roller

including cost of material labour plant and

equipment etc. complete.

157 Compaction and finishing of cement concrete 1002.00 Sqm 63.63

road by trimix process providing extra Labour

charges for the trimix vacume dewatering service

process on cement concrete road sutface by using

vacuum dewatering pump floater surface

vibrator including making groves and rough

finish to surface including leveling etc complete.

158 Constructing providing and fabricating cattle 18.00 Sqmt 4785.38

guard using channel section frame of size ISMC

series 100 mm x 50 mm (Weight 9.20 kg/Rmt)

and ISMC section 100 mm x 75mm (weight

kg/Rmt) intermediate support for welding

G.I.pipe at 12 Cm C/C of size 50 mm in a frame

made of Channel section size 100 mm x 50 mm

all round including fixing the unit on prepared

chamber of masonary wall using MS hold fast

embeded in masonary wall top as directed by

Engineer in charge and as per drawing and

necessary required arrangement etc complete.

159 Providing and fixing decorative entrance gate 1575.00 kg 173.72

made out of cast iron and various mild steel

tabular section combination , the Ornamental

entrance gate should be fixed at compound wall

including pattern and die making , cutting

welding , grinding, fabrication , fixing in position

at compound wall with necessary pedestal,

bearing block and other locking arrangement.

The entrance gate should be painted with two

coats of priming coat of paint, and two coat of oil

paint etc complete. As per detail design and

instruction of architect.

Item Description of Item Quantity Unit Rate In Amount

160 Providing and fixing concertina coil fencing with 194.00 Rmt 460.56

punched tape concertina coil 600 mm dia 10 mt

openable length having 50 no rounds per 6 mt

length, upto 3mt height of wall with existing

angle iron (50mm x50mm x5mm )requird

shaped As per Directed Engeenier in charge.

placed 2.4mt or 3.00mt apart and with

horizontal R.B.T. reinforced barbed wire(3 mm)

stud tied with G.I. staples and G.I. clips to retain

horizontal, including necessary bolts or

G.I.barbed wire tied to angle iron, all complete as

per direction of Engineer-in-charge, with

reinforced barbed tape (R.B.T.)/Spring core (2.5

mm thick) and weight 43.478 gm/meter at

compound wall for ESR M4/ intakewell.

161 Supply. installation, testing & commissioning of 1.00 No 68680.00

ISI approved electrical motor driven jockey

pump set having 450 LPM @ 50m head. The

pump unit shall be a horizontally direct mounted

motor. Unit shall comprise the following

minimum requirements:

a) Pump, b) Electric motor IE2, c) Foundation

bolts, d) Mating flanges with gasket and

fasteners, e) Discharge gauges, etc. complete in

all respect, with labour, with GST.

162 Supply, fabrication & erection of aboveground 200.00 Rmt 474.70

G.I. 'C'-Class, ERW piping, conforming to IS:1239,

part-I, Heavy class up to 150 mm dia. and

IS:3589, for size 200 mm dia. & above, thickness.

G.I. pipe fitting's as per IS: 1239, part-II, Heavy

class for size 150 mm dia. & below & IS: 3589, for

size 200 mm dia. above, flanges, nuts bolts &

washers, 3 mm thick gasket, pipe hangers, etc.

Hydrostatic testing for 2 hour's at 150% of the

system pressure, hook-up etc.

Painting for piping, fittings & structural pipe

support, shall be two coat of zinc primer and two

coats of fire red conf. to IS: 5, Shade

Complete with all accessories as per approved

drawings, specicification and direction of the

Engineer-in-Charge, with all complete.

Item Description of Item Quantity Unit Rate In Amount

163 Supply, fabrication & erection of aboveground 50.00 Rmt 1989.70

G.I. 'C'-Class, ERW piping, conforming to IS:1239,

part-I, Heavy class up to 150 mm dia. and

IS:3589, for size 200 mm dia. & above, thickness.

G.I. pipe fitting's as per IS: 1239, part-II, Heavy

class for size 150 mm dia. & below & IS: 3589, for

size 200 mm dia. above, flanges, nuts bolts &

washers, 3 mm thick gasket, pipe hangers, etc.

Hydrostatic testing for 2 hour's at 150% of the

system pressure, hook-up etc.

Painting for piping, fittings & structural pipe

support, shall be two coat of zinc primer and two

coats of fire red conf. to IS: 5, Shade

Complete with all accessories as per approved

drawings, specicification and direction of the

Engineer-in-Charge, with all complete.

164 Design , Supply and installation of Safety Signage 15.00 sqmt 3787.50

made of Zinc Sulphilde based glow in dark , Rigid

sheet with High Luminous property enclosed in a

transperent weather proof UV stabilized plastic

pasted on 3 mm thick clear acrylic sheet such as

EXITS, EMERGENCY EXIT, DO NOT USE LIFT

DURING FIRE, FLOOR MARKINGS, FIRE LIFT,

STAIRCASE EXIT, FIRE ALARM CALL POINT,

FIRE HOSE REEL, FIRE HYDRANT POINT etc.

165 Supply, installation, testing & commissioning of 1.00 No. 3333.00

pressure switch. (Range 0 to 16 kg/cm2)

166 Supply, installation, testing & commissioning of 2.00 No. 3232.00

150 mm dia. dial Burdon Type Glycerine Filled

pressure gauge with isolation ball valve

arrangements with necessary isolation valves

with all complete.( Range 0 to 15 kg/cm2)

167 Supply, Installation, Testing & Commissioning of 5.00 No. 3686.50

Cast iron body Butterfly valve according to IS:

13095, PN-1.6, Iron Disc for size 150 mm dia. &

below Lever operated and above 150 mm dia.

Gear operated complete with mating flanges

/ANSI class # 150 with bolts & nuts washers,

rubber gaskets 3 mm thick, etc., with all

168 Supply, installation, testing & commissioning of 1.00 No. 2121.00

SG iron body SinglePlate Wafer Type NRV conf. to

ASTMA 536, PN-1.6 complete with mating

Flanges class # 150 with bolts & nuts, washers,

gaskets 3 mm thick, etc., with all complete.

Item Description of Item Quantity Unit Rate In Amount

169 Supply, installation, testing & commissioning of 1.00 No. 6019.60

Two way fire brigade Inlet connection with

mm dia. stainless steel (SS304) instantaneous

male inlets with built in non return valve in each

inlet with 100 mm dia. header pipe, suitable

rubber cap and GI chain including nuts, bolts,

washers, gasket 3 mm thick, etc. with all

170 Supply, Installation, testing & commissioing of 3.00 No. 8736.50

Swinging type mild steel hose reel drum with

mm dia. x 30 Rmt. rubber hose as per IS: 884. The

mounting stand shall be of mild steel and the

hose shall be fitted with a SS shut-off nozzle & SS

ball valve of 25 mm dia. including supporting

arrangement with all complete. accessories

171 Supplying, fixing & testing of of SS ball Valve 10 1.00 No. 565.60

172 Supplying, fixing & testing of of SS ball Valve 15 2.00 No. 666.60

173 Supplying, fixing & testing of of SS ball Valve 20 3.00 No. 787.80

174 Supplying, fixing & testing of of SS ball Valve 1.00 No. 833.25

175 Supply,Installation And Commissioning Of Hose 6.00 No 353.50

Nipple with Pipe Clamp

176 Filling Of Gaps Between pipe and Core Cutting 18.00 No 454.50

Hole With Chemical and Cement

177 Supply,fabrication and erection of Structure MS 150.00 Kg 101.00

Material as like Angle, C channel,I Beam Etc.

178 Supply, installation and commissioning of 100.00 Rmt 222.20

Copper Flexible cable for 7.5 HP Motor - 4 sq mm

179 Supply and Fitting Change Over Switch (GEB/DG) 1.00 No. 9090.00

180 Supply, Filling and Fixing of approved make ABC 8.00 No. 2323.00

type fire extinguisher - 6 Kg. Capacity as per

181 Supply, Filling and Fixing of approved make CO2 8.00 No. 6514.50

type fire extinguisher. Capacity 4.5 Kg.

(conforming to IS-15683).

182 Submitting the application to obtain Fire NOC for 1.00 No. 50500.00

one year to SMC Department,Providing complete

practical demonstration of fire system in

presence of fire officer and Submitting the

photographs of demonstration, refilling and

testing certificates of fire extinguisher,Obtaining

and providing certificate of FPCOR, Payment of

NOC Fees to SMC Department, Preparing the

documents of Affidavit and AMC with

Notorization And Submitting to Department,

follow up to receive NOC And Providing to R & B

Including all above expenditure.

Item Description of Item Quantity Unit Rate In Amount

183 Supply, Installation and commissioning of 100% set 15150000% 15150000%

Fabricated Stair case made up of MS angle and

channel for emergency exit.

184 Supply, Installation and commissioning of Fire 2.00 No 22725.00

Alarm Panel Conventional type, 2 zone, with

complete accessories.

185 Supply, Installation and commissioning of Audio 10.00 No 1262.50

hooters , with complete accessories.

186 Supply, Installation and commissioning of 10.00 No 1191.80

Manual Call Points, with complete accessories.

187 Cable(Armour) for Fire Alarm system 250.00 Rmt 111.10

188 Core cutting in wall and in RCC slab with size 50 10.00 No 505.00

189 Core cutting in wall and in RCC slab with size 150 10.00 No 757.50

190 Providing and laying polished Kota stone slabe 2.00 Sqmt 628.22

25mm thick in risers of steps,skirting Dedo and

pillars laid on 10mm thick cement mortar 1:3 (1-

Cement : 3 coarse sand) and jointed with gray

cement slury mixed with pigment to match the

shade of slab including rubbing and polishing etc.

191 Clearing and grubbing road land including 0.13 Hect. 28455.08

uprooting rank vegetation grass

bushes,shrubs,sapling and trees girth up to

mm removal of stumps of trees cut earlier and

disposal of unserviceable materials (C) By

mechanical means in area of light jungle

192 Earthwork for embankment including breaking 3803.00 Cumt 169.38

clods, dressing with all lead and lift (excluding

watering and consolidation)(E) From Borrow

area within all lead

193 Rolling of earthwork in layers with power roller 3803.00 Cumt 22.88

including filling in depressions which occur

during the process and Watering of earth work as

194 Point wiring for Light / Bell with 2-1.5 sq.mm 384.00 Pt. 485.81

& earth wire of 1.5 sq.mm (Green) both are of ISI

marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length , in

below type of pipe erected with 6A Modular type

switch / bell push & accessories and earth

continuity of following type, erected on PVC /

Metallic/Wooden box, single mounting base

frame covered with textured/metallic/white

front plate modules erected on / in wall / ceiling

as per pipe erected, with necessary Lamp

holder/ceiling rose / H.D.Connector as

directed.(f) with medium class Rigid PVC pipe

and accessories erected concealed in wall/ceiling

completeCat. III

Item Description of Item Quantity Unit Rate In Amount

195 Point wiring for FAN with 2-1.5 sq.mm & 149.00 Pt. 674.68

earthwire of 1.5 sq.mm (Green) both are of .ISI

marked 1.1 KV Grade FRLS PVC insulated

multistrand copper wires, in following type of

pipe to be erected concealed in / flushed on

wall/ceiling complete with 6A Modular type

switch and hum free EME four or more step type

electronic fan regulator with separately mounted

and accessories with earth continuity of

following type erected on PVC / Metallic box,

single mounting base frame covered with

textured/metallic front plate modules erected on

/ in wall / ceiling as per pipe erected. with

necessary ceiling rose / H.D.Connector as

directed.(f) with medium class Rigid PVC pipe

and accessories erected concealed in wall/ceiling

complete Cat. III

196 Point wiring for on board Looped Plug with 6A

Modular type switch & 5 pin socket erected on

PVC / Metallic/Wooden box, single mounting

base frame covered with textured /

metallic/white front plate modules erected on /

in wall / ceiling with following type accessories

Cat. III 71.00 Pt. 257.55

197 Providing following type of Modular Type

Accessories mounted with pvc / metallic box,

single mounting base frame covered with

textured / metallic front plate , modules erected

with necessary connection. As desired by

Engineer In charge

(3) Two Pin/RJ-11 Telephone Socket

[A] For One Gang 14.00 0.00 160.59

(4) TV Co-axial Socket outlet

Cat.III 5.00 Nos 160.59

(8) Computer RJ-45 socket

Cat.III 80.00 Nos 160.59

(9) 16 Amp. SP one way switch

Cat.III 80.00 Nos 180.79

(10) 6/16Amp. Universal socket

Cat.III 80.00 Nos 199.98

198 Providing and erecting ISI mark Medium class

RIGID PVC PIPES of following size complete to be

erected on/in wall or ceiling erected with

necessary PVC fittings & Junction boxes fixed

with adhesive solution & Clamps with following

dia of pipes, in approved manner as directed

Item Description of Item Quantity Unit Rate In Amount

199 Providing and erecting Mains with 1.1 KV grade

FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be

erected concealed in /flushed on wall/ceiling,

with 1.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth

continuity of following size

(a) with medium class Rigid PVC pipe and

(b) 2 wire 2.5 sq. mm 3245.00 Mtr. 82.82

200 providing and erecting Mains with 1.1 KV grade

FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be

erected in / on wall / ceiling with 2.5 sq. mm

copper conductor FRLS PVC insulated stranded

wire of green colour for earth continuity of

(a) with medium class Rigid PVC pipe and

(a) 2 wire 4 sq. mm 1170.00 Mtr 112.11

(i) 4 wire 10 sq. mm 260.00 Mtr. 425.21

(use earth wire of 4 sq.mm )

201 Mains with ISI marked, 1.5KV grade electrolyte

multi stranded, annealed copper conductor with

heat resistant PVC insulated conforms to IS

IEC - 227 erected in existing pipe of following

size (Specifically for control panel, relays, power

switchgears, motor starters & control wiring)

with required size of copper lugs, nuts and bolts

(g) One wire 16.00 sq. mm 60.00 Mtr. 142.41

(k) One wire 70.00 sq. mm 5.00 mtr 669.63

202 Supplying and erecting Flexible PVC insulated

multi strand multi core 1.1 kv grade ISI marked

copper wires of following size to be erected as

(e) 1.50 Sq.mm 3 core round PVC sheathed 110.00 Mtr 46.46

203 Providing & Erecting approved make following

size of TV Co-axial flexible cable comprising inner

conductor of solid bare copper insulated with

Foam PE & Secondary conductor made of poly -

Aluminium film bonded Al. Braids @ suitable

coverage overall sheathed with black PVC

Item Description of Item Quantity Unit Rate In Amount

204 Supplying & erecting approved make Telephone

Cable electrolytic copper conductor PE insulation

twisted in two pairs, & wrapped with FRLS PVC

tape & sheathed with FRLS PVC or HFFR outer

Jacket suitable for telephone wiring & confirming

to C-DOT erected in existing pipe. of following

size of conductors & nos.of pairs. With necessary

[A] Conductor Size 0.5 mm

(2) Two Pairs 420.00 Mtr 20.20

(b) Armoured [Jelly Filled]

(2) Twenty Pairs 50.00 mtr 199.98

205 Supplying & erecting approved make LAN cable

of following size in existing pipe as per direction

206 Providing & erecting main Distribution (MDF)

indoor type, back mounted frame as per DoT

standard approved with krone strips

(b) Suitable for 20 pair 3.00 Ea. 1368.55

207 Providing & erecting Switch board for

Computer or electric apparatus consisting of

following modular type accessories mounted

with PVC / Metallic concealed/open box with

single mounting base frame covered with

textured/metallic /white front plate,modules

erected with necessary connections as directed

1 no. 6A/16A universal plug-switch combined.

3 nos. 6A Switch

3 nos. 6A 5 pin Plug

[B] For Modular Type Accessories

Cat. III 88.00 Nos 1133.22

208 Supplying & erecting Approved make call bell 3.00 Nos 148.47

indicator with buzzing sound and Red light

indicating lamp with Red light button to attend

the call suitable for 240 v 50 c/s supply to be

209 Decorative call bell Ting-tong box type 250 volts 11.00 Nos 71.71

complete erected

Item Description of Item Quantity Unit Rate In Amount

210 Supplying and erecting LED indoor fittings with 305.00 Ea. 373.70

LEDs of wattage 0.2 Watt to 0.5 Watt assembled

on single MCPCB, with housing used as a heat

sink shall be made of thick sheet Steel

conforming to IS: 513/CRCA/ aluminium die cast

powder coated and high U.V. & corrosion

resistance with diffuser with company

mark/name 160V to 270V, Power Factor more

than 0.95, THD < 15%,

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80

Certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.)(A)

Tube Light with integral driver(iv) 22-24 Watts,

Surge - 2KV,IP-20, conventional 4 feet Cat. III

(i) 5-10 Watts, Surge-2 KV, IP-20, conventional 1 19.00 Ea. 165.64

to 2 feet Cat. III

211 Supplying and erecting LED indoor fittings with

LEDs of wattage 0.2 Watt to 0.5 Watt assembled

on single MCPCB, with housing used as a heat

sink shall be made of thick sheet Steel

conforming to IS: 513/CRCA/aluminium

pressure die cast powder coated and high U.V. &

corrosion resistance with diffuser housed in

aluminium casted body with company

160V to 270V,Power Factor more than 0.95, THD

CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt

LED driver efficiency > 85 %

( fitting required LM-79 & LM-80

Certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.)

(B) LED Panel Light with provision for Plane 16.00 Ea. 1794.77

front frame with translucent cover fixed to

housing complete.IP20(vi) 36 watts, 24" x 24",

Surge- 2KV Cat. III

Item Description of Item Quantity Unit Rate In Amount

212 Supplying and erecting LED street light / Flood

light fittings with High power White LEDs

wattage of 3 Watt and above assembled on single

MCPCB, efficiency more than 130 lm/w and

corrosion free High pressure die cast aluminum

housing with smooth finish powder coated and

heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened

glass with company mark/name engraved or

embossed 160 to 270 V,Power Factor more than

5700K,Uniformity ratio >0.45, Luminaire

efficacy> 100 lumens/watt . LED driver efficiency

> 85 %.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.)

(A) Street Light (IP-65), Surge protection -4KV

integral and ,Light must have 440VAC line supply

with over-voltage protection.

(i) above 36 to 48 watts Cat-lll 14.00 ea 3345.12

(B) Flood Light (IP-65), Surge protection -4KV

integral and ,Light must have 440VAC line supply

with over-voltage protection.

(iii) Above 60 to 90 watts

Cat-lll 10.00 ea 6088.28

(C) Post Top Lantern LED fitting comprises of

finish cast aluminum spigot and spun aluminum

canopy fixed with opal polycarbonate, pipe

arrangement for vertical mounting driver and

accessories wired upto terminal block.IP

213 providing and erecting Miniature circuit breaker

single pole 6A to 25A suitable to operate on

V A.C. system and having breaking capacity

KA to be erected in existing box. confirming to IS

8828/1996 with ISI Mark

Cat-III 276.00 Ea. 112.11

214 Providing & erecting 415 V MCB Four Pole for

Motor & Inductive Load (C Curve) having 10KA

breaking capacity & confirms to IS :8828 in

existing box having following capacity

Cat.III 15.00 Ea. 737.30

Item Description of Item Quantity Unit Rate In Amount

215 Providing and erecting Sheet Steel powder

coated MCB distribution board - flush / surface

mounted fitted with busbar, neutral link, earth

bar and DIN rail, Conforms to IS 8623-1 & 3, IEC

61439-1 & 3 without MCB to house appropriate

nos. of MCBs.(The DBs should be used of same

company of MCB to be used) suitable for

(B) three phase incoming and single phase

horizontal type outgoing Per phase isolation

(b) sheet steel double door

(iii)8 way 6.00 ea 3412.79

216 providing and erecting Approved make RCCBs

conforming to IS: 12640 and having sensitivity of

30 mA and Short Circuit withstand capacity of

KA and suitable for operation on single phase

240 V,50Hz. having characteristic of quick action

& tripping with all advance feature & do not

incorporate any electronic component. for

following Max. rating erected as directed

(ii) 40Amps. DP

Cat. III 33.00 Ea. 2235.13

217 Pproviding and erecting Approved make Four

pole moulded case circuit breaker having

breaking capacity ICU of 25 KA. at 415 V,having

normal current rating up to 25 A to 100A. with

Fixed thermal & magnetic release suitable to

work on A.C. supply 50 c/s. with all internal

connections, spreader tinned copper & complete

erected in existing 16 G.M.S. housing.

ICS=100% of ICU only Cat III 19.00 Ea. 6173.12

218 Providing and erecting Approved make Four pole

moulded case circuit breaker having breaking

capacity ICU of 35 KA. at 415 V. having Normal

current rating 200A.with variable Thermal &

magnetic release suitable to work on A.C.supply

50 c/s. with all internal connections, spreader

tinned copper & complete erected in existing

ICS=100% of ICU only Cat III 6.00 0.00 16221.61

219 Providing and erecting Approved make Four pole

moulded case circuit breaker having breaking

capacity ICU of 35 KA. and above at 415 V .

having normal current rating 250A. with

variable thermal & magnetic release suitable to

work on A.C.supply 50 c/s. with all internal

connections, spreader tinned copper & complete

erected in existing 16 G.M.S. housing.

Item Description of Item Quantity Unit Rate In Amount

ICS=100% of ICU only Cat III 1.00 Ea 20946.39

220 Providing and erecting Approved make Four pole

moulded case circuit breaker having breaking

capacity ICU of 35 KA. and above at 415 V .

having normal current rating 250A. with

variable thermal & magnetic release suitable to

work on A.C.supply 50 c/s. with all internal

connections, spreader tinned copper & complete

erected in existing 16 G.M.S. housing.

ICS=100% of ICU only Cat IIINote:-1 Add 1.00 Ea. 23041.03

Rs. 10% extra for housing/Encloser of MCCB for

Item No 3-4-1 to 3-4-12 (The Enclosures should

be used of same company of MCCBs to be used)

221 Providing and erecting Approved make Earth

fault Relay suitable to mount with inter

connection suitable to following size of moulded

case circuit breaker having CT ratio & MCCB

rating as following along with shunt trip 220V

AC. with all internal connections & complete

erected in existing M.S.housing..

222 Supplying & erecting approved make Four Pole

415V change over switch interior for panel

mounting with operating mechanism A.C.23 duty

confirming to IS for

223 Supplying and erecting triple pole & neutral 440V

/ 500V panel mounting Copper Busbars with four

equal Nos. of electrolyte bus having current

density not more than 1.6 Amp. / sq.mm (Rated

current / cross section area) duly wrapped with

colour insulating tape for phase sequence of

following current carrying capacity, erected with

necessary bus bar supports /insulators, main

cable socket to each bar, erected in existing

cubical panel with necessary connections.

(A) Suitable for 100 Amp. Capacity 0.50 Rn.Mtr 1961.42

(B) Suitable for 200 Amp. capacity 1.00 Rn.Mtr 3202.71

(C) Suitable for 300 Amp. capacity 0.50 Rn.Mtr 4909.61

224 Providing and erecting Annealed bare Copper 80.00 KG 794.87

wire 8 to 16 SWG.

225 Providing and erecting Pipe type earthing having 14.00 ea 368.65

150 cms.long and 2.5 cms. dia. galvanised iron

pipe with coupling and buch buried in specially

prepared earth pit complete with necessary

SWG earth wire.

226 For using salt and charcoal / coke as required for 14.00 ea 171.70

pipe type earthing.

Item Description of Item Quantity Unit Rate In Amount

227 Supplying & erecting earth pit of minimum bore

dia.150mm size approved make Earthing

Electrode consisting Pipe-in-Pipe Technology as

per IS 3043-1987 made of corrosion free hot

dipped G.I.Pipes having Outer pipe dia of 50mm

having 80-200 Micron galvanising, Inner pipe dia

of 25 mm having 200-250 Micron galvanising,

connection terminal dia of 12mm with constant

ohmic value surrounded by highly conductive

compound with high charge dissipation suitable

for following type of applications with chamber

and heavy duty cover. (A)(approved make OEM

has to submit test certificate including value of

earth resistance of installation duly stamped and

signed by agency and officer Incharge has to

ensure the value of earthing resistane mentioned

in test Certificate) & having back filling

compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 ohm / meter testing

as per IEC 62561-2017, Voltage drop:- < 1 volt at

no load & dry form, Sulphar content:- <2%(C)

Back fill Compound :- Earthing compound should

be capable to retain moisture for long time

Necessary test report must be submitted by

(a) For Electrical Installation up to 440V in 8.00 Ea. 4591.46

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

228 Providing & erecting weather proof, dust &

vermin proof, floor mounted front operated

indoor type cubical panel board necessary IP-42

and above protection as per approval from

engineer incharge made from 14 SWG thick CRC

M.S. sheet for outer body & doors, 16 SWG thick

CRC M.S.sheet for internal partitions with

necessary accesories , supporting angles/ flats

channel including cutting, bending, drilling,

welding, riveting with internal partitions & cable

alley as per requirements & instruction of

engineer-in-charge with erection of

Item Description of Item Quantity Unit Rate In Amount

supplied switch gears, BUSBARS, suitable size of

inter connecting PVC copper wire / copper-

aluminium strips, rubber grommets, rib, bakelite

control fuses/MCB for measuring instruments,

earth bus & earth bolts, foundation flange - bolts-

base Plates, sufficient nos. of hinged doors,

handles with locking arrangement and rubber

gasket,heavy duty end terminal

connection,danger notice board,necessary

ventilation,earthing strip complete. The Panel

shall be painted with epoxy powder coating.

(The rates excludes the cost of switchgears, bus

bars, inter connecting mains & Copper

Aluminium strips, meters, Fuses etc. The

dimension shall be measured excluding base

beams) The panel shall be supplied with

following approved manufacturers with

following size.

(B) locally fabricated panel board

(i) with 350 mm depth 6.00 Sq.Mtr 10468.65

229 Providing , erecting , fabricating the M.S. 500.00 Kg. 77.77

structure as per requirement on site

incorporating proper size of M.S. angles, flats,

bars, channels, sections complete with cutting,

welding, grinding & finishing duly painted with

one coat of red oxide with erection on site as per

direction of engineer in charge with necessary

grouting, cementing, plastering & finishing

230 Providing & erecting stand alone ceiling mount 18.00 Ea 4366.23

PIR motion Sensor with ABS Housing single

phase AC operation. Complete with Dual element

pyroelectric sensor, Digital Signal Processing

Detection Range 14 feet at 10 feet height, angle

360 degree, RFI and EMI immunity, Detects

motion in it's coverage area. Multipurpose device

can be used as security device, an energy saving

device, an automatic switch. Complete with infra

red sensor, Light & sensitivity Sensor, Timer with

Bye pass facility. Suitable for 400 watts electrical

231 Supplying and erecting approved make panel 5.00 Ea. 1275.63

mounting type Digital Voltmeter having 3 digits

LED display, 0 to 750 AC Volts range erected on

existing panel board with all connection, wiring

etc .with manufacturers calibration certificate.

Item Description of Item Quantity Unit Rate In Amount

232 Supplying and erecting approved make panel 5.00 Ea. 1558.43

mounting type Digital Ammeter having 3 digits

LED display, external CT operated, calibrated for

0 to 1000 Amps suitable to operate on 500 Volt

AC , erected on existing panel board with all

connection, wiring etc .with manufacturers

calibration certificate.

233 Supplying and erecting Ammeter / Voltmeter 10.00 Ea. 317.14

selector switch for 3 phase AC Supply 500 V on

existing panel board with necessary connections.

234 Providing & erecting L.T. Current Transformer 15.00 ea 274.72

with bar primary 50/5 to 1000/5 ratio 15 VA

burden erected in existing CRCA box duly

secured with insulating materials connected to

235 Providing and erecting metallic vitrified danger 5.00 Ea. 69.69

notice board as per language suggested by

engineer incharge for MEDIUM VOLTAGE

installation to be erected as per IS-2551.

236 Providing and erecting XLPE(IS:7098)(I)-88 ISI

armoured cable multistrand Aluminium

conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of

following size of cables

(A) 3 1/2 core 25 Sq. mm ( 16 Sq. mm 1/2 core) 200.00 Mtr. 183.82

237 Providing and erecting XLPE (IS:7098)(I)-88 ISI

armoured cable multistrand / Solid Aluminium

conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of

following size of cables

(B) 4 core 6 Sq. mm 200.00 mtr 126.25

238 Providing and erecting XLPE (IS:7098)(I)-88 ISI

armoured cable multistrand Aluminium

conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of

following size of cables

(A) 4 core 16 Sq. mm 400.00 mtr 153.52

239 Making trench in soft soil of suitable width of 90 600.00 mtr 55.55

cm deep for laying cable or locating the fault all

over the run and back filling the same and

making the surface as normal ground.

240 Making trench in Hard Murrum / Tar Road of 20.00 mtr 74.74

suitable width of 90 cm or required depth for

laying any size of cable or locating the fault all

over the run and back filling the same and

making the surface as normal ground.

Item Description of Item Quantity Unit Rate In Amount

(B) If additional machinery like hammer driller 10.00 mtr 357.54

or JCB use [Add]

241 Drilling the road without breaking the road

surface (Asphalt) for laying of cable for feeding

power supply by making up to following size of

holes at both ends complete.

(A) Up to 100 mm bore dia 20.00 mtr 492.88

242 Supplying following size of Light duty “A” Class

G.I . Pipe & erecting as directed by Engineer-in-

(A) 25 mm dia 40.00 mtr 172.71

243 Providing & laying approved make Double

walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with

necessary connecting accessories of same

material at required depth in existing trench for

laying of cable. below ground / road surface for

enclosing cable

(A)50 mm outer dia 600.00 mtr 62.62

244 Providing & laying approved make ISI marked

Rigid PVC pipe having 6Kg / cm2 (Class-3) to be

erected at road crossing on or floor as directed

for laying of cable. The pipes as following size of

dia & weight per 6 mtr.

(E) 90 mm inner Dia (8.0 Kg / 6RMT) 20.00 mtr 171.70

245 Providing and, fixing heavy duty flange type

brass cable gland with rubber ring for PVC

insulated armoured cable complete with out

going tails, insulating tape etc for following size

(B) 2 to 4 core 6 Sq. mm 20.00 ea 38.38

246 Providing and, fixing heavy duty flange type

brass cable gland with rubber ring for PVC

insulated armoured cable complete with out

going tails, insulating tape etc for following size

247 Solderless crimping type Aluminium lugs

conforming to IS suitable for cable of following

size evenly crimped with high pressure tool &

connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved

Item Description of Item Quantity Unit Rate In Amount

248 Providing and fixing approved make Perforated C

type cable tray. Made from sheet steel. The cable

tray should be single or double bended as per

required and as per IS 2062/1079 and shall be

coated with hot dip galvanizing as per IS

2629/4759. with max 17.5% perforation with

coupler plate / Fish plate and GI hardware like

nut - bolt and washers etc. erection with

necessary support( included) as per

Specification and as per instruction of engineer in

249 Providing and fixing approved make 'T' Junction

for Perforated C type cable tray. Made from

sheet steel. The Junction should be bended as per

IS 2062/1079 and shall be coated with hot dip

galvanizing as per IS 2629/4759. with max

17.5% perforation with coupler plate / Fish

plate and GI hardware like nut - bolt and washers

etc. erected on existing support as per

Specification and as per instruction of engineer in

charge of following size

250 Providing and fixing approved make '90° Elbow'

for Perforated C type cable tray. Made from

sheet steel. The Junction should be bended as per

IS 2062/1079 and shall be coated with hot dip

galvanizing as per IS 2629/4759. with coupler

plate / Fish plate and GI hardware like nut - bolt

and washers etc. erected on existing support as

per Specification and as per instruction of

engineer in charge..

(5) 300 X 50 X 2.0 mm Thick 90° Elbow 3.00 ea 245.43

251 Providing & erecting Approved make Ceiling Fan 12.00 Ea 1982.63

with double ball bearing with Condenser 230 volt

A.C.50 Hz. 900 mm sweep complete having

Aluminium blades, canopy erected complete. [

Make shall be approved by Engineer in Charge]

252 Providing and erecting Approved make Ceiling 137.00 Ea. 1596.81

fan with double ball bearing ISI mark with

condenser A.C. 23OV.50 c/s.1200 mm. sweep

complete, canopy erected on existing hook or

clamp with earthing. [Make shall be approved by

Engineer in charge]

253 Supplying and erecting 19 / 20 mm. nominal 149.00 mtr. 108.07

bore Medium Class M.S. Pipe down rod erected

duly painted for fan complete with necessary 24/

O.20, 3 core flexible wire with earthing.

Item Description of Item Quantity Unit Rate In Amount

254 Supplying & erecting fan hook box of 10 mm 149.00 Ea. 108.07

M.S. round bar bounded to the RCC bars up to

50mm length each side and pierced through a

Gauge M.S. box / Heavy Duty PVC box complete

erected concealed in Ceiling with necessary

255 Providing 2.5mm.thick laminated acrylic sheet to 149.00 ea 18.18

cover the fan hook or Fan box.

256 Supplying & erecting single phase approved

make industrial exhaust fan suitable for medium

duty ring mounted low noise operation suitable

for medium duty having following dia size and

maximum speed in RPM

[A] 305 mm dia 900 RPM Cat.II 29.00 Ea. 2054.34

257 Providing recess in wall or window frame 29.00 Ea 189.88

suitable for erection of Exhaust fan complete

with plastering and colour washing to match the

colour of the wall or window complete with

expanded metal in order to render the fitting in

accessible and the room water-proof.

258 Supplying and erecting approved make Octagonal

pole made from HR sheet steel. The pole should

be made as per IS. and shall be coated with hot

dip galvanizing as per IS 2629/2633/4759,

suitable suspend local wind speed with integral

Junction box consist of terminal plate of min

6mm Hylam sheet, standard profile

35mmX7.5mm Din-Rail for MCB Mounting, stud

type terminal and arrangement for cable

termination to be erected With Suitable

foundation (Included) as per details given by

manufacturer considering site requirement.

(D) 6 Mtr. Long 70 mm Top X 135 mm bottom 14.00 ea 8192.11

dia, 3 mm thickness with

200mmX200mmX12mm base plate, 4-M20 Bolts

and 600mm long with necessary G.I. J Bolts

.Approx Pole weight 59 kg

259 Supplying & erecting approved make SMC press

moulded composite FRP. loop-in, loop-out

approx. 2mm thick box complete with Bakelite

connector strip 5way(3P+N+E),DIN rail for

mounting mob & hinged doors as per

requirement having locking arrangements with

mounting clamp with nuts, bolts & washers

suitable for erection on pole with cable clamps&

earth bolt of following size of box.

(A) 300mm x 200mm x 100mm [deep] 10.00 ea 898.90

Item Description of Item Quantity Unit Rate In Amount

260 Providing and erecting Street Light pole bracket

comprising main B Class GI pipe of

cm/require outside dia. complete with suitable B

Class G.I. sleeve tubing of approx. 45cms.length

and suitable for 76.5 mm /80mm / required size

of pole top having sufficient fasteners for fixing

the brackets and having spread of 1.5.mtr. length

with 110 deg.with vertical plane & suitable

welded stays, reducer and with check nuts

complete painted with one coat of Red oxide / PU

base primer and two coats of Aluminium / PU

paint. paint with following nos of arms.

[A] Single Arm Bracket 1.5 Mtr 14.00 ea 683.77

261 Supplying & erecting IP 55 grade following size

section pillar fabricated from joint less M.S. Sheet

with angle iron legs made from jointless M.S.

Angle with cable clamps to be buried in ground

to have appropriate erection to work uniform

until erected with cement concrete foundation

and 45 cm high bricks work finishing with

plaster etc. hinged double door internally

supported on both side,

with internal and outside looking arrangement

with look and keys in duplicate 35 x 35 x 5 mm

M.S. Angle of Two Nos. one is welded and other

with nut and bolt for erecting Bakelite sheet.

Painting the Section Pillar inside and out side

with three tank powder coated paint. section

pillar roof should be without joint with water

leakage proof & tested as per IP 55 test &

followed by IS 2147 of

(B) 75 X 60 X 45 cm section pillar fabricated from 1.00 ea 3595.60

16 Gauge MS Sheet with angle iron legs 45 cm

long made from 35 X 35 X 5 mm thick MS angle.

262 Supplying and erecting HYLAM sheet on existing

angle iron frame.for following thickness

263 Supplying & erecting approved make Digital time 1.00 ea 3168.37

switch having lithium cell 6 years operative and

operate battery backup 1 channel day clock with

14 memory programme, suitable to operate on

240V + 5%, 16A with, floating contacts Minimum

switching setup time 1 minimum & LCD display.

Also comprised permanent ON/OFF switching.

Programming switches & housed in fire proof

thermoplastic enclosure & transparent cover

erected as required with necessary connection

erected as directed.

Item Description of Item Quantity Unit Rate In Amount

264 Supplying & erecting power contactor ,AC3 duty

for time switch complete erected as per direction

265 Providing and erecting Small EPABX System with

In Built 4 Port Voice Mail [[Approved by

Competent Authority i.e. not Below the rank of

Executive Engineer ]

[C] No. Extension -24 , No. of Junction -8 , No. of 1.00 ea 78180.06

expandable ports -96 , Operators Console -01

Compatible - ISDN

266 Supplying & erecting push button type telephone 14.00 ea 898.90

instrument having speaker phone Caller ID &

speaker phone with one touch memory (min.6

nos.)& 99 memories with display system Single

line [[Approved by Competent Authority i.e. not

Below the rank of Executive Engineer ]

267 Providing & erecting, programming, testing of 1.00 ea 5992.33

chairman unit microphone with flexible stem of

480 mm in length and light ring built in loud

speaker ,two head phone socket ,attractive

design ,priority button for chairman

microphone,built in volume control for head

phones,chime tone facility to precede chairman

priority calls,microphone on/off button,red

indicates for microphone is active,frequency

response -400Hz to 10kHz,nominal acoustic

input -85 dB SPL [[Approved by Competent

Authority i.e. not Below the rank of Executive

268 Providing & erecting, programming, testing of 18.00 ea 5565.10

Delegate unit microphone with flexible stem of

480 mm in length and light ring built in loud

speaker ,two head phone socket ,attractive

design ,built in volume control for head

phones,chime tone facility to precede chairman

priority calls,microphone on/off button,red

indicates for microphone is active,frequency

response -400Hz to 10kHz,nominal acoustic

input -85 dB SPL [[Approved by Competent

Authority i.e. not Below the rank of Executive

269 SITC of Prefabricated to reduce installation time 5.00 ea 9124.34

Low smoke zero halogen to comply with safety

and environmental standards 10 Meter

[Approved by Competent Authority i.e. not Below

the rank of Executive Engineer ]

270 SITC of Mixer amplifier, 240W 1.00 ea 22000.83

[Approved by Competent Authority i.e. not Below

the rank of Executive Engineer ]

Item Description of Item Quantity Unit Rate In Amount

271 SITC of Cabinet loudspeaker, 30W, black 6.00 ea 13399.67

High-fidelity music and speech reproduction

Selectable 8 ohm, 70 V and 100 V inputs

Compact yet robust ABS enclosure

Supplied with adjustable mounting bracket

Complies with international installation and

safety regulations

[Approved by Competent Authority i.e. not Below

the rank of Executive Engineer ]

272 SITC of 3LCD Lamp based projector having wxga 1.00 ea 33895.60

(1280x800) or better resolution with minimum

white brightness of 3800 lumens and color

brightness of 3800 lumens. The projector should

have minimum 1HDMI,1VGA input. Having

contrast ratio of 15000:1 or more. the projector

should have auto vertical key stone correction of

+/- 30 degree and Manual Horizontal of +/-30

degree. the projector should have optical lens,

throw ratio 1.30-1.56:1. Zoom Factor of 1.2. Lens

focus Manual having focal length 16.9mm to

20.28mm. projector should have features like AV

mute slide, quick corner and split function and

should support wireless functionality with

inbuilt wifi or wifi dongle. [Approved by

Competent Authority i.e. not Below the rank of

Executive Engineer ]

273 SITC of universal Projector mounting kit, with 1.00 ea 6848.81

necessary grouting, fasteners etc. with adjustable

height and suitable for all types of projectors.

[Approved by Competent Authority i.e. not Below

the rank of Executive Engineer ]

274 SITC of 84 inch Self Lock MW (6 x 4) Instalock 1.00 ea 3379.46

Slow Retraction Screen, Aspect Ratio-4:3

[Approved by Competent Authority i.e. not Below

the rank of Executive Engineer ]

275 SITC of CAT6 UTP 23AWG Solid: Per Meter 200.00 mtrs 43.43

[Approved by Competent Authority i.e. not Below

the rank of Executive Engineer ]

276 SITC of 2-Core Shielded PVC Coated Oxygen-Free 200.00 mtrs 115.55

Microphone Cable, Cross-Sectional Area 24AWG,

DC Resistance - 35 /Ω Km, Operating Voltage -

300 V, Operating Temperature ,-20⁰ C to 70⁰ C,

Make :- Crestron/Extron/Krystal/Kramer

277 SITC of 2-core 1.5 sqmm PVC-coated twisted 160.00 mtrs 106.99

oxygen-free speaker cable, Cross Sectional Area -

1.5Sqmm, Insulation Dia. - 2.90mm, DC resistance

@20 °C – Conductor -13.7.0 Ω / Km, Operating

Temperature ,-20⁰ C to 70⁰ C.Make :-

Crestron/Extron/Krystal/Kramer

Item Description of Item Quantity Unit Rate In Amount

278 SITC of HDMI Cable with 10 meters length, High- 1.00 Ea 8987.33

Speed HDMI Cable with Ethernet, supporting

resolutions up to 4K @ 60Hz, HDR (High

Dynamic Range), with a bandwidth of 18 Gbps.

Connectors are HDMI Type-A (Male) to HDMI

Type-A (Male), gold-plated for enhanced signal

transfer and corrosion resistance. Features

include ARC (Audio Return Channel), 3D, Deep

Color, and HDCP 2.2 support. The cable is triple-

shielded for minimum interference and

maximum signal integrity, with a durable PVC

jacket and strain relief for flexibility and long life.

It is compatible with all HDMI standards (1.4, 2.0,

etc.) and certified to meet HDMI standards for

safe and reliable performance. Make :-

Crestron/Extron/DVDO/Kramer

279 Providing and erecting Galvanised iron floor 78.00 Nos 1792.90

mounting height adjustable junction box having

size of 150x150x65-90mm.

280 Supplying and erecting insulated pair of soft 25.00 Rn.Mtr 965.56

copper tubing open or concealed including power

and control cable,necessary PVC drain pipes for

Split AC machine up to 4 TR capacity

281 SITC of 22U Wall Mount Network Rack with 1.00 Ea 27817.94

Front Acrylic Door with lock & keys, Ventilated

Top and Bottom., Accessories can be added are

Power Strip, Cooling Fan, Cantilever Tray, Cable

Manager, Mounting Hardware, Size(WxDxH)

600x600x583 Make :- Rittal, elixir, valrack

282 Providing and erecting Inverter based approved

make split air-conditioning unit consisting of

condensing unit with variable speed fan motor,

inverter type hermetically sealed rotary

compressor with accessories etc. duly connected

separately erected evaporating unit and blower

motor with its accessories by means of extra

supplied proper insulated copper tubing,drain

PVC pipes suitable for ( cost includes Eco

Friendly green gas charging and 15A plug top &

Remote Control & MS Stand) with necessary core

(1)For ISEER Range (KWH/KWH)(3.1 to 3.99)

(C) for 1.7 to 2 ton capacity - Premium Cat. 5.00 Ea. 56353.96

Item Description of Item Quantity Unit Rate In Amount

283 Providing & erecting water cooler having storage 3.00 ea 55893.40

capacity 150 Ltr. & cooling capacity 150 Ltr.per

hour @ an ambient temp of 45˚ C. The outlet

temp. of the water should drop by 15˚C within a

hour, The water cooler should be comprising of

hermetically sealed compressor, fan motor,

condensing unit, water tank surrounded by

evaporating, coil, thermostats, relay etc.complete

with necessary inlet & outlet connection. The

body of water cooler will be made from Stainless

284 Supplying & erecting 5 stage single reverse

osmosis water purification system with M.S.

powder coated frame, prefilter housing with 'O'

ring presediment filter GAC filter, carbon filter

suitable buster DC pump capacity 80 psi, mention

with 40 psi inline type post carbon filter auto low

& high pressure switches with following size of

storage tank & LPH capacity & erected as

[C] 50 Ltr / Hr with 150 psi 2 nos booster pump 3.00 ea 29187.99

285 Providing & erecting open well horizontal mono

block pump set with cast iron body, complete for

three phase submersible motor having

[D] For 5 HP 3 phase open well horizontal mono 2.00 ea 18746.61

block pump set suitable for 1350 LPM to

LPM @ 10 to 42 Mtr head suitable for 50/65 mm

dia delivery pipe Cat.II

286 Supplying & erecting approved make motor

control cubical panel (Direct - on - line) made

from 16 G. CRCA sheet duly epoxy powder

painted inside and outside with hinged doors and

locking, arrangement consisting of suitable size

of ON- OFF isolator (AC - 3/23duty) main fuses,

single phasing preventer, indicating lamps for R-

Y - B phases, overload relay, Automatic water

level controller, Ammeter, Voltmeter each with

two way selector switch incoming, wires duly

socket crimped, main contactor & overload relay,

start - stop push buttons, to be erected on angle

iron frame grouted on wall as directed. The

isolator, overload relay & contactors will be of L

& T, Siemens or BCH make only.

(A) DOL up to 5.0 H.P. 2.00 ea 7722.46

Item Description of Item Quantity Unit Rate In Amount

287 Lowering of submersible motor pump set at the

depth of following ,complete with required. Nos.

and size of casing pipes erected by means of

proper chain pulley block & pipe wrenches after

checking of threads of each pipe with coupling to

take the load of the pump set and pipe assembly

filled up with water

(D)For Open well Horizontal submersible pump

set for sump well

(i) 1 HP to 5 HP 2.00 per job 856.48

288 Providing and erecting ISI marked PVC insulated

PVC Sheathed Flat flexible Submersible copper

cable approved make of following Size.

(C) 3 Core x 4 Sq. mm 60.00 mtrs 146.45

289 Providing Water proof straight Joint in PVC

insulated flat flexible copper cable by using

insulating material, water proofing material, &

making the joint complete.

290 Supplying & erecting UPVC heavy duty Flanges

with rubber packing and hardware materials for

pipe connections suitable for

291 Supplying and erecting ISI marked sluice valve at

position with necessary material for following

size of pipe diameter.

292 Supplying, & erecting C.I. swing, check type non-

return (Reflux) Valve -ISI marked suitable for

293 Supplying of following size of HEAVY UPVC

column pipe with coupler and wire lock

[B] 50 mm dia 40.00 mtr 359.56

294 Supply of following size of TOP & BOTTOM

accessories i.e. Adaptor set (CI) long, pump guard

set, starter pipe Rubber ring for submersible

pump & UPVC column pipe as directed by

Engineer - in - charge with necessary plumbing

[D] 50 mm dia 2.00 per job 1489.75

Item Description of Item Quantity Unit Rate In Amount

295 Supplying and erecting, commissioning and

testing of Diesel Generating set confirming to IS:

4722:1968 & BS:5514 having continuous rating,

3 phase, 415 volts, 50 cycles A.C. supply

comprising of a totally enclosed air/water cooled

diesel engine with multi-cylinders developing

suitable BHP not less than following capacity at

1500 RPM with 10% overload for one hour in

hours with standard accessories like fly wheel,

lubricating oil cooler, "A" class governor, heavy

duty fuel wheel and lubricating oil filter, oil bath

air filler, lubricating oil pressure gauge, end

exhaust manifold, standard set of tools with

adjustable spanners, screw drivers, cylinder head

to cover, joint cylinder head to exhaust, element

lube oil filter, 12 / 24 volts electric starting

equipment complete with standard heavy duty

battery, dynamo, cut-outs, ammeter, necessary

wiring, pressure gauge, starter etc and heavy

duty Residential type exhaust silencer (With DEF

System) and vertical hot air duct both

logged with asbestos rope, save oil trays, exhaust

piping of required length, standard wall/floor

mounted fuel with level indicator and piping and

drip proof alternator, self excited, self regulated,

screen protected, with excitation system, capable

of delivering the rated system output at

volts, 3 phase, 0.8 PF, 50 Hz, 4 wire, running at

1500 RPM, conforming to IS-4722- 1968 with

voltage regulation +/- 5% of rated voltage

from no load to full load. Both the engine and

alternator fitted on a common fabricated steel

base plate with antivibration mounting engine

and alternator both connected to each other by

flexible flange coupling and with floor/wall

mounted control panel box comprising of

voltmeter ammeter, selector switches, ACB /

MCCB / MCB of adequate capacity,

Item Description of Item Quantity Unit Rate In Amount

indicator lamps duly wired with HRC fuses. The

alternator & control panel shall be connected

with provided suitable capacity armoured cable

and complete with Acoustic enclosure (canopy)

made out of 16 SWG CRCA Sheet, sound

absorbing material Rockwool of 64 density &

mm thick conforming to IS:8183 / PU Foam of

Density - at least 40 mm. The resin bonded

rockwool covered from inside the canopy by

perforated sheet with 3/4 mm holes, sound level

not more than 75 dB at a distance of 1 mtr, as per

PVCT norms.DG set should have in built fuel tank

capacity of minimum 8 hrs of continous running

capacity on full load . Erection, commissioning

and satisfactory testing as per requirement with

first filling of fuel (minimum up to the 80% of

fuel tank capacity), oil, etc. with guarantee /

Warrantee of complete system for Two years. &

with obtaining all necessary certificate from

Electrical Inspector. The Capacity and Ratings of

DG sets are as below. (As per new CPCB4+

Emission norms Engine With - Turbo Charger,

EGR (Exhaust Gas Recirculation), CRS (Common

Rail Fuel System), DOC (Diesel Oxidation

Catalyst), SCR (Selective Catalytic Reduction),

Integrated wiring harness connected to ECU .)

(J) Continuous rating of 75 KVA ,BHP not less 1.00 ea 720245.14

296 Providing & erecting approved make AMF control

panel suitable for following size of 3 phase,

V., 50 cycles, A.C. diesel generating set complete

of scope as detailed below:

1) Power module: A pair of electromechanically

interlocked contactors (for mains & generator)

Overload relay for generator contactor Neutral

contactor for mains and generator Power socket

for connections.

2) Control and metering module: Line voltage

monitor. Generator voltage monitor Ammeter

items attempt start facility. Air circuit

breakers/MCB/MCCB of suitable rating for

auto/manual operation. Auto/manual switch.

Emergency stop push buttons. Manual start push

button. frequency meter. Engine hour meter. Two

earthing studs.

Item Description of Item Quantity Unit Rate In Amount

3) Protection module: The engine shutdown in

the unlikely event of Low lube oil pressure High

cylinder head temperature. V belt failure.

4) Indicators with alarm Load on generator.

5) Indicators Load on mains Engine fails to start .

Emergency stop battery charger.

The AMF Panel of following capacity

(B) AMF Control Panel for75 KVA/82.5 KVA3 1.00 ea 110758.62

297 Supplying, Erecting, Testing & Commissioning

the passenger / stretcher lift having following

(A) GENERAL DESCRIPTION OF LIFTS.

[1] GEAR LESS LIFT DRIVE (MRL) comprising of

High Starting torque Lift 3 phase 440 V A. C.

Permanent Magnet Synchronous motor of proper

rating with high efficiency shall be used.[2] Micro

processor based / PLC, ACVVVF, vector control

drive with encoder feedback closed loop system

shall be used for lift car and door operation

which shall be full collective selective operation

hall call demand response, UP/DOWN hall stops,

Main, Up/ Down Contactor with overload and

phase reversal relay and safety controls.

[3] Car with M S platform with bracings of

adequate size and to sustain the impact load

cabin + passenger with safety factor of fire for

steel and side panels of Stainless steel of sheet of

grade 304 duty. Car ceiling will be S.S. finishes

with aesthetic appearance with LED ceiling

lights. Car flooring shall be of s/s 304 chaker

plate design sugeested of engineer in charge. of

engineer in charge. Car doors shall be of stainless

steel grade 304, hairline finish with centre

opening / telescopic automatic doors. Car panel

will also be S.S. 304 finished with emergency stop

device, mechanical door safety device, facility of

auto/ attended mode. All car panel buttons and

all floor switches must be with brail language as

Item Description of Item Quantity Unit Rate In Amount

[4] All landing doors must be fire rated for 2 hour

shall be fully automatic centre opening/

telescopic opening made of hairline finish steel

grade of 304 with key holes and infrared curtains

with Unlocking facility from outside

[5] Appropriate battery operated emergency

light in the car along with alarm switch shall be

provided. Also, Emergency Light & Fan should

start immediately without any Time Delay as

soon as power fails.

[6] Digital scrolling indicator system for up-down

arrow along with floor position indicator shall be

provided inside the car and at all floors.

[7] Full height infra red curtain with multiple

cross / crossing light beams shall be provided.

[8] Automatic Rescue Device (ARD) shall be

provided accordingly of passenger capacity with

Manual Rescue Operation ( Manual Cranking

[9] Audio visual indication in the lift car showing

over loading shall be provided such that doors

kept open till excess load is removed.

[10] Spring buffers/PU Buffers shall be provided.

[11] Car fan as per passenger capacity with

automatic sleep timer shall be provided.

[12] Voice annunciator with suitable music shall

be provided in lift car.

[13] Self diagnostics system for operational and

safety parameters shall be provided in control

[14] Mechanical over speed governor with

governor calibration as per actual site

parameters and submission of calibration

certificate submission, door key holes in the floor

doors, fireman switch shall be provided.

[15] Lift machine hoisting arrangement in the lift

machine room and monkey ladder for lift pit

should be provided by the lift agency, along with

the other steel structure works, foundations for

the machine etc…

[16] In the hoist way fascia plate shall be

provided without any extra cost, where ever

required as / if directed by engineer in charge.

Item Description of Item Quantity Unit Rate In Amount

[17] Permanent wiring with necessary safety

devices like RCCB in all circuit, Over Voltage

Under Voltage protection and THD eliminator in

circuit for lift machine room and lift well with

proper numbers of light points, with fixtures,

exhaust fan and plug points shall be provided by

the agency. Only 3 phase Power Supply shall be

made available by department in lift machine

room. Necessary Earthing as per Lift Act/Rules

shall be arranged by Lift Agency.

[18] Any civil/ electrical works for additional and

alteration in lift shaft and machine room related

to erection of lift shall be made by lift agency

without any extra cost. (granite/marble fixing

around all landing door openings are not in lift

agency’s scope.)

[19] Agency has to provide all working drawings

and documents and liaison services for obtaining

all necessary permission from lift inspector and

other authorities. [20] acrylic transparent

licence/display A4 size holder in lift car

[20A] As per statutory requirement of Govt. Of

Gujarat lift & escalator act 2000, lift agency has to

1. Car top safety barricade

2. Push & talk communication system.

3. Fireman's switch operation at Ground Floor.

4.carrying out third party lift inspection

during/after lift erection and provide report by

third party authorized by concern licensing

authority 5.agency has to provide third party

insurance upto completion of free maintenance

period and submit the document for the same.

[21] Car Panel Operating Buttons with floor

position indicator/buttons must be of Auto Glow

type clearly visible when view from inside cabin.

[22] For Physically Handicapped person Full

Length Handrails of hairline finish steel grade of

304 should be provided at appropriate height on

the Rear & Side Wall Panels in Lift Car. [23]

With Necessary KVA rating voltage controlled

Stabilizer suitable for your controller, drive and

all equipments of lift.

[24] Necessary rating of DP Elcb and FP Elcb

required for lift is in scope of work which rating

is sugested by CEICED Department (electrical

Item Description of Item Quantity Unit Rate In Amount

8 / 10 Passengers, Ground plus 2 upper floor

with Rated Speed of 1.0 m/sec.,

(B) With General Specification attached herewith. 1.00 ea 1249812.38

I/We am/are willing to carry out the work at………………….% above/below percent(Should be written in

figures and words) of the estimated rate mentioned above. Amount of my /our

Tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

In words In words

The Contractor shall exhibit a board with detailed specification and details of work as directed by the

1 Engineer-In-Charge for which no extra payment shall be made.

2 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3 Income tax TDS will be deducted at a source while making payments of bills

In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.:

PRC-10/2017 Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C.

4 items where there is a change as per actual mix design the cost of difference of cement consumption

have been deducted from the rate of original item at the rate of input rate mentioned in all the tender.

Deputy Executive Engineer Executive Engineer

( R & B ) Sub Division ( R & B ) Division