PROVN OF COOK HOUSE, DINNING HALL AND VIEW CUTTER FENCE AT KGBS AND BLDG. NO P-7 AT GHUNGHORA CANTT UNDER GE DEHRADUN

Amount

Excavation in trenches, n exc 1.5 mtr wide and n exc 1.5 mtr in depth for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. for laying of cable n exc 10 Sqm on plan and n exc 1.5 mtr in depth and getting out in hard/dense soil complete all as specified and directed.

M&L for plain cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation, filling and mass concrete, complete all as specified and directed.

Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter flat rough finished surfaces of concrete complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia & over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality complete all as specified and directed.

All as per item No 4 above, but 6mm to 8mm dia.

All as per item No 4 above but 5mm dia and over up to and including 10mm dia as in stirrups, spacers and binders complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix) 1:1.5:3, type A-1, (20mm graded aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions square, rectangular or polygonal for rough finished surfaces of concrete complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix) type A-1,1:1.5:3 (20mm graded aggregate) in Columns, pillars, piers, posts and struts complete all as specified and directed.

Use and waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. flat rough finished surfaces of concrete complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix) type A-1, 1:1.5:3 (20mm graded aggregate) in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Use and waste of formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) flat rough finished surface of concrete complete all as specified and directed.

M&L for reinforced cement concrete (nominal mix) type A-1 1:1.5:3 (12.5mm graded aggregate) in slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

M&L for Formwork to chullah hoods, chajjas, troughs and similar items including edges, flat rough finished surface of concrete complete all as specified.

M&L for Reinforced cement concrete (nominal mix) type A-1 1:1.5:3 (20mm graded aggregate) in Chajjas complete all as specified and directed.

M&L for 40mm Damp proof course in cement concrete course 1:2:4 type B0( using 12.5mm graded stone aggregate) to horizontal or vertical surfaces mixed with integral water proofing compound as per manufacturer instructions including necessary formwork complete all as specified and directed. Note:- Water Proofing Compound shall be measured and paid separately.

M&L for brick work with subclass 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar (1:6) (using old size bricks) complete all as specified.

M&L for brickwork with sub- class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar (1:4) complete all as specified and directed.

M&L for cement concrete 1:2:4 B-0 (using 12.5 mm graded stone aggregate) in coping, bed plates and chamfered angles and throating etc complete all as specified and directed.

M&L for 15 mm thick rendering on fair faces of brick work or concrete surface in cement mortar 1:6, surface finished even and fair complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar 1:4 on other than fair faces of brick work or concrete surface, surface finished even and fair complete all as specified and directed.

Supply only Liquid water proofing compound

Returning filling including spreading, leveling, watering and well ramming in layers n.exc 25 cm complete all as specified and as directed.

Removal of excavated soil n. exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

M&L for Sand filling under floors or in foundations including watering and consolidation complete all as specified and directed.

M&L for hardcore of broken stone gauge exc 40mm but n exc 63mm deposited, spread and leveled in layers n exc 15 cm thick watered and rammed to a true surface complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in plinth protection or similar work/places, laid in alternate bays and filling the joints with & including bitumen and sand 1:3 by weight, surface finished even and fair without using extra cement complete all as specified and directed.

M&L for PCC 1:4:8 type D2 (using 40mm graded crushed stone aggregate), 75 mm thick as in sub base complete all as specified and as directed.

M&L 25 mm thick PCC 1:2:4 type B-0 using 12.50 mm graded stone aggregate as in leveling course to floors complete all as specified and as directed.

M&L for vitrified ceramic coloured tiles 10 mm thick light shade (square/rectangular) polished area of each tiles not exceeding 0.36 sqm, in floor etc. set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

M&L heavy duty endura ceramic coloured tiles 10 mm thick dark shade (square/rectangular) polished area of each tiles not exceeding 0.36 sqm, in floor etc. Set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar 1:6 and dismantling of existing floor tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and as directed.

M&L for glazed ceramic colour tiles size 300 mm x 450 mm x 6-7 mm thick on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10 mm thick rendering in cement mortar 1:4 and dismantling of existing wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and as directed.

M&L for Machine cut kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

M&L for Machine cut kota stone as in skirting 15-18 thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and as directed.

M&L 18 to 20 mm thick Granite(of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

M&L for grinding and polishing to edges and rounding of granite kota or marble slab and smooth finishing complete all as specified and as directed

S&F Pressed steel frames of size 105x60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and as directed.

S&F Pressed steel frames of size 125x60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and as directed. Note for srl item No 37 & 38: Hollow portion of frame shall be filled with cement concrete1:2:4 type B-0 ( 12.5 mm stone aggregate), cost of same shall be included in the quoted rates

S & F 35mm thick second class hardwood (Golden Teak) glazed and Skelton factory made door shutters, open rebated and prepared to receive glass/gauze etc divided into squares with plain, chamfered or rounded mitered and rebated sash bars, edges of framing plain, chamfered, fitting with cut and rebated beads for securing glass/ gauge complete all as specified in SSR Pt I-2009 section 8 clause 8.24 (a) and as directed.

S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides including provision of suitable blocks for taking mortice locks, latches or other fittings complete all as specified and as directed.

S&F factory made 100 % solid wood plastic composite (WPC) door frame 75x50 mm made from wood plastic composite (single extruded process) material with density 780 Kg/Cum from ISO certified company door should be water proof, termite proof, fire retardant and having good screw holding capacity all as per specification and drawing as directed by Engineer-in-Charge.

S&F 30 mm thick moulded WPC factory made 100% solid door (conforming as per IS-4020) made from 100% lead free single extruded with 2, 4 or 6 raised panel design on the front side with 10 mm deep mould on single side with wood grain texture and back side palin with density not less than 600 Kg/cum. Manufactured by an ISO : 9001-2015 certified company. The door should be water proof, termite proof, fire retardant and having screw holding capacity complete all as specified.

S&F stainless steel barrel tower bolts 150 mm long one piece and fixed complete all as specified and as directed.

S&F stainless steel butt hinges, medium weight 100 mm long one piece and fixed with screws/welded to frame complete all as specified and as directed.

S&F stainless steel handles 150 mm long one piece and fixed with screws/welded to frame complete all as specified and as directed.

S&F factory made steel window with side hung shutters including box type hinges with steel handle, steel peg stay, tower bolt etc. complete with glazing bars, dovetailed or welded complete all as specified and as directed.

S&F factory made steel window with side hung shutters including box type hinges with steel handle, steel peg stay, tower bolt etc. complete without glazing bars, dovetailed or welded complete all as specified and as directed.

S&F factory made steel ventilator with top hung shutters including hinges with steel handle, steel peg stay, tower bolt etc. complete all as specified and as directed.

S&F stainless steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm complete all as specified and as directed.

S&F 4 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in square area n. exc. 0.5 Sqm in each pane complete all as specified and as directed.

S&F mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 including necessary welding, drilling hole complete.

S&F factory made 100 % solid wood plastic composite (WPC) flush type shutter of 18mm thickness one side laminate consisting of panel of PVC profile of 18mm (+ 0.7mm) thick of density 600 kg per cum manufactured by ISO-9000 certified company using for shutter cillicia ply 18mm thick and fixed with frame. The thickness of shutter is edges painted by matching colour of PVC lining of plain/prelim coloured PVC sheet using etc complete as per manufacture specification complete all as specified and as directed.

S&F magnetic catcher and striking plate including letting in and fixed complete all as specified and as directed.

S&F Continuous (PIANO) hinges, mild steel, bright finish or electrogalvanised. 30 mm width of flaps (when open) complete all as specified and as directed.

M&L for mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe 410 -W (Gde-E- 250) quality-A complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws and profile should match with galvalume sheet complete all as specified and as directed..

Providing & fixing false ceiling of Designer tile Ivory painted (High Pressure Steam cured) of 4mm thickness (as per IS : 14862) of size 595x595mm and any one of the design (Cascade or Electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel section (Galvanised @120 grms, both side inclusive and black painted groove on all T webs)

consisting of main T runner with suitably spaced joints to get required length and 15x32mm made from 0.30mm thick sheet spaced at 1200mm c/c and cross 'T' of size 15x32mm made of 0.30mm sheet 1200mm long spaced between main "T" at 600 mm c/c to form a grid of size 1200x600mm and secondary cross "T" of length 600mm and size 15x32 mm made of 0.30mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x22x0.40mm and laying false ceiling tiles in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable wire of 4mm dia with galvanised butterfly level clips, spaced at 1200mm c/c along main 'T', bottom exposed width of 15mm of all 'T'' sections of 4mm dia GI wire shall be pre-painted with polyester paint and black painted groove at center of size 4mm depth and 4.5mm width, including taking down existing ceiling of any type all complete at all heights as per direction of Engineer-in-Charge.

M&L applying two coats of synthetic enamel paint on new or previously untreated steel surfaces of any description over 10 cm width or girth over a coat of red oxide primer including preparation of steel surfaces complete all as specified and as directed.

M&L applying two coats of Synthetic paint on new wooden surfaces of any description over 10 cm width or girth over a coat of pink primer including preparation of surfaces complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer complete all as specified in SSR Part I and directed by Engr-in-Charge.

M&L for preparation of newly plastered surface of wall and applying two coat of cement base paint over a coat of primer complete all as specified and as directed.

S&F vitreous china squatting pan “ORISSA PATERN” of size 580 mm x 440 mm, white, with integral foot rest (excluding flushing cistern and flush pipe) including connection to trap and to flushing pipe, anti syphonage pipe etc and making good to floor complete all as specified and as directed.

S&F 10 litre capacity PVC low level cistern ‘ white’ with inlet, float valve including brackets with 32 mm dia PVC pipe/bend 600 mm long complete all as specified and as directed.

S&F vitreous china wash hand basin white, oval type counter top of size 550mmx400mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe, waste fitting etc. complete all as specified and as directed.

S&F pillar taps, brass, with capston heads, fancy type chromium plated, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and fly nuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed. Make : Jaguar/Cat part No. KUP-35001PM/Hindware Cat Part No:F370001/Parryware Cat Pat No.T4302A2

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including cantilever brackets of suitable angle iron, CP brass waste coupling ,superior quality PVC waste pipe and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tanks Capacity of tank 1000 litres triple layer, white colour, (cylindrical vertical with closed top) hoisted and fixed in position, all as specified in SSR part I-2009 including dismantling of existing unserviceable tank and removing from site, complete all as specified and as directed.

S&F ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size (Minimum weight 210 gms) complete all as specified and as directed.

S&F Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in 15 mm bore Angle cock/stop valves, cast copper alloy, fancy type chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed. Make : - JAGUAR Cat Part No FON-40053/Hindware Cat Part No F160017/Prayag Cat No 9410

S&F 15mm bore Bib taps long body cast copper alloy fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. Make : - JAGUAR CAT Part No ALI-85037/Hindweare CAT Part No F-370004/Prayag CAT Part No S9906

S&F CP grating 100mm to 125 dia round fix on floor/ nahani trap with hole/without fixed with cement mortar, complete all as specified and directed.

S&F looking mirror mounted on decorative type PVC frame fixed to wooden plug with CP brackets screw fixed, complete all as specified and as directed.

S&F 20 mm dia brass chromium plated towel rack of 3 sets type 60cm long between flanges including pair of fixing brackets complete all as specified and directed.

S&F 15mm bore pipe medium grade galvanised iron with all fittings fixed to wall and ceiling or laid in floor complete all as specified and directed.

S&F 20mm bore pipe medium grade galvanised iron with all fittings fixed to wall and ceiling or laid in floor complete all as specified and directed.

S&F PVC connection 15 mm dia 450 mm long with brass fly nut at both ends complete all as specified and as directed.

S&F 75 mm bore UPVC (SWR) pipe pressure 4kgf/cm2 single socketed in any length with rubber ring, fixed on wall / laid in trenches complete all as specified and directed.

S&F 110 mm bore UPVC (SWR) pipe pressure 4kgf/cm2 single socketed in any length with rubber ring, fixed on wall/ laid in trenches complete all as specified and directed.

S&F 75 mm bore UPVC (SWR) bend with oval access door ,'T' socket reducer etc complete all as specified and as directed.

S&F 110 mm bore UPVC (SWR) bend with oval access door ,'T' socket reducer etc complete all specified and directed.

Cutting into existing manholes for connecting new drains 150mm dia making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required complete al as specified and directed.

Excavating in post holes (or similar holes) in hard/dense soil each n exc 0.5 cu. M, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surface in any type of soil complete all as specified and directed.

M&L for mild steel work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

M&L for point wiring with 1.5 Sqmm. (nominal area) FRLS, single core PVC insulated 1100 Volts, grade multi stranded copper conductor unsheathed in and including concealed PVC conduit medium duty 20 mm dia or higher and heavy grade conduit fittings and heavy duty accessories with suitable size of sunk type cast iron or pressed steel terminal box 1.6mm thick for mounting of switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet as top cover, one green colour FRLS cable of same size as earth wire up to common earth and connected to earth dolly compete all as specified and directed by Eng.-in-charge of following. Note: The wiring to be done as per IE rule and maintain colour code accordingly.

(a) One light point/ point controlled by one-one way switch.

(b) One ceiling fan point/ Exhaust fan point controlled by one-one way switch.

(c) One bell point controlled by one-one way switch.

(d) One three pin 5 Amp socket on same board with other switches.

(e) One three pin 5 Amp socket on independent board

All as per item No. 86.00 above but one 3 pin socket outlet 15 Amp independent, cable 2.5 Sqmm PVC insulated unsheathed multi stranded copper cable FRLS for phase & neutral, with 2.5Sqmm PVC insulated unsheathed multi stranded copper conductor cable FRLS as earth continuity conductor.

S&F switch piano flush, button type 5 Amp SP 250 V AC complete all as specified & directed.

S&F switch piano flush button type 15 Amps SP 250 V AC complete all as specified & directed.

S&F socket outlet multipurpose 3 Pin 5 Amp and 2 Pin 5 Amps 250 V AC complete all as specified & directed.

S&F socket outlet two in one three pin 5 Amp and 15 Amp 2 module 120 W flush type compete all as specified and directed

S&F Bell switch piano flush button type 5 Amp compete all as specified and directed.

S&F ding dong bell AC 230 V single pole complete all as specified and directed .

S&F step type regulator socket type double module 5 step for ceiling fan 1200/1400 mm size 230 volts 6 Amp 400 watts compete all as specified and directed.

S&F ceiling rose, 3 terminal/PVC/polycarbonate, isolated body 250 V AC compete all as specified and directed.

M&L lamp holder insulated body with back plate suitable for angle and batten fitting compete all as specified and directed.

M&L sub main wiring with 2 Single core PVC insulated unsheathed FRLS cable 1100 Volts grade heavy duty copper conductor multi stranded of size 10 Sq.mm. (nominal area) drawing in and including 20 mm. dia or higher PVC concealed conduit heavy duty accessories and fittings. PVC insulated unsheathed FRLS cable copper conductor multi stranded of size 6 Sq. mm. as earth wire upto common earth and connected to earth dolly compete all as specified and directed.

S&F sheet metal enclosures 240 volt with 200 Amp rated bus bar for double door 8 way DB,s IP-43 IK 09 metal door suitable for one MCB SPN as incoming and 06 MCB SP as out going compete all as specified and directed.

S&F sheet metal enclosures Triple pole and neutral double door 415 Volt 4 way DBs IP-43 IK- 09 Vertical type suitable for 200 Ams rated bus bar & one MCCB 100 Amp as incoming and 12 MCB SP as outgoing compete all as specified and directed.

S&F MCB double pole 240 Volt 10 KA 40 Amp 'B' series conforming to ISI marked compete all as specified and directed.

S&F MCB single pole and 240 volt 10 KA 5-32 Amp 'B' series conforming to ISI marked all as specified and directed Make Legrand/Schneider/ABB...

S&F MCCB 415 Volt 16 KA 4 pole 63 Amp magnetic trip release & setting as incoming with fixing arrangement compete all as specified and directed.

S&F in replacement wall mounted tube light fitting 1x20/22 watts extruded aluminium polycarbonate covers PF 0.9 and above operating voltage 140V-270V colour temp 6500K & lumen input output 95 Lumen per watt and connected to ceiling rose with required length of two core flexible copper cable 23/0.0076 fixed on wall/roof complete all as specified and directed. Make: Philips cat part No TMC 501P1xT LED 22WP-3241(Tube Batten) and MAS LE$D 1200mm 18W-865-T-81 (Tube) / Wipro Cat part No WI0922208 (Tube Batten) LL13-181-65SE (Tube)/ Havells Cat Part No LUMILINEPLUSBS20WLED865SPCSS (Tube Batten)CRYSTAL1213T8DSTL20WLED865SGLASS(TUBE DOUBLE SIDE)

S&F in replacement LED light fitting decorative wall mounting SS brush finish fixture with frosted glass suitable for upto 1x40 watt mini glass lamp with and including one no 12 watt LED lamp. complete with accessories and including connecting up with twin core twisted flexible copper conductor cable of suitable size compete all as specified and directed.

S&F mirror light decorative compact luminaries with decorative ends caps 9/10 Watt LED with all accessories and including connecting up with three core flexible copper conductor cable of suitable size compete all as specified and directed.

S & F high efficiency LED bulbs 1 X 12 watt that can be used as a ready replacement for existing GLS ad CFL direct fit in holder complete all as specified and directed.

Supply and Fixing Integral LED Bldg Security Light Luminaire comprising of pressure die cast aluminum housing heat resistant toughened glass with frame IP-65 protection road way luminaries with high power LED 60 watt with efficiency 100 lumen/watt at system level, CCT>5700K, with average life class 50,000 burning hours including taking out old unserviceable street light fittings complete all as specified and directed. Make:- Crompton model No. LSTP-45-CDL/Havells model No. ENDURAPEARLNEOSL 40WLED757PASYTOPC /Philips Cat Part No BRP409LED CW036MRFGIPSUGRand SYSKA SSK-ST-40W

S&F in replacement of ceiling fan 1200 mm sweep single phase 230 volts copper winding, double ball bearing with down rod , canopy, blades etc including connecting with twisted three cord flexible copper conductor cable (23/.0076 ) from ceiling rose to connector of fan complete all as specified and directed.

M&L for stone/brick wall cutting in circular shape, grouting or suitable bolts suitable for 300 mm exhaust fan and making disturbed surface good plastering and distempering etc complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm, 900 RPM, single phase, 230V AC with louver all as specified and directed 30 mm sheet. including connection with twisted white three core flexible copper multi stranded conductor cable from ceiling rose to connector complete all as specified and directed.

Supply and fix exhaust fan, steel body AC single Phase. 230V of size 450 mm, 900 RPM, single phase, 230V AC with louver all as specified and directed 30 mm sheet. including connection with twisted white three core flexible copper multi stranded conductor cable from ceiling rose to connectorcomplete all as specified and directed.

S&F in replacement of Geyser vertical mount type 25 Ltrs capacity five star rated , shockproof and rust proof metal body compact size including two nos PVC connection heavy duty and connecting with all fixing arrangement of nuts & bolts and fixing on wall complete all as specified & directed .

S & F Sheet metal enclosure SPN with a two pin and earth plug and socket complete with one 240 Volts 20 amp single pole MCB complete all as specified and directed.

Supply & laying Sand coarse dry as in cushioning of underground electric cable in trenches, laid to a uniform thickness of 23cm (15cm under the cable & 8cm over the cable ) and gently punned down to 18cm thickness all complete all as specified and directed. Note :- Only punned down sand thickness 18CM shall be measured and paid.

Supplying and laying old size bricks, laid flat ie length of brick shall be laid across the cable, common burnt clay building bricks sub class `B' designation 75 complete all as specified and directed and testing on completion complete all as specified and directed.

Supply, laying, jointing and testing of underground XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 25 Sqmm 4 Core laid in trenches/ducts/along poles/through pipe under road etc with new aluminium lugs of cable size complete all as specified and directed.

Supply and laying galvanised steel tubing 50 mm bore light grade laid in trenches or fixed to poles/walls etc for cable protection complete all as specified and directed.

Materials and Labour for earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6.0 mm thick buried directly in ground end vertically to a depth not less than 2.25 meter deep below ground level with top edge of the earth plate at a depth not less than 1.5 M below normal ground level connected to galvanized steel earth wire 4 mm dia by means of bolts, nuts check nuts and washers of galvanized steel and connected to main switch board or main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1, cover slab 54 cm x 54 cm x 5 cm reinforced with 8 mm dia. TMT bars @ 150 mm c/c both ways, and with one handle for lifting made out of 10 mm dia MS round bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 15 mm bore galvanized steel tubing (light grade) for protection of earth lead connection, including necessary excavation and earth work in any type of soil and necessary testing complete all as shown on electrical plate No 3 of SSR Part –I (2009) and as directed.

M&L for Cutting existing steel tubing for alterations or additions (Each cut measured) pipe making connection of GI Pipe distribution branch with GI main of size 16 to 40 mm bore complete all as specified and directed.

Screwing existing steel tubing for alterations or additions (or lengthening screw on pipe to form connector) of size 16 to 50 mm bore complete all as specified and directed.

Supply, Laying, fixing & testing galvanished iron water tubing 'medium grade; 20 mm dia with and including all GI fittings such as flanges, unions reducers sockets, socket reducing bends , elbows, tee, check nuts, caps, plugs etc laid in trenches for the following sizes complete all as specified and directed.

All as per item No 121 above but galvanished iron water tubing 'medium grade; 40 mm dia. Note for srl item No 121 & 122: Excavation and earth work shall be measured and paid separately under respective item of schedule 'A"

M/S C S AITHANI

M/s RP AGRAWAL

V K Constructive Builders

M/S Construction Solutions

M/s RAM RATAN AND SONS