CERTAIN REPAIRS AND MAINT OF EXTERNAL DISTRIBUTION CABLES, CONNECTED ITEMS IN CERTAIN UNIT LOCS AND REPAIR/REPLACEMENT OF STREET LIGHTS AT CERTAIN OTM ACCN IN NAA UNDER GE (N) TEZPUR

Amount

Note 1: (Applicable for all parts/items) : The biidders/contractors are advised to read tender document, all drawings & all corrigendum/amendments and general condition of contracts before entry/quoting the rates. Note 2:- Attention to bidder is hereby invited to upload revised BOQ if published during their bid submission. Uploading of incorrect/ pre-revised BOQ shall be treated as non bonafide and rejected. Fixed credit has been given in technical documents which shall be taken into account during acceptance of bid/tender.

Taking down down/dismantling old/rusted/broken steel poles/struts,removing from site and making good disturbed surface complete all as specified and directed.

Taking down down/dismantling old/rusted/deshaped cross arms/MS channel or angle for reuse complete all as specified and directed.

Dismantling insulators any type, any size including setting aside serviceable and removal of rubbish material complete all as specified and directed.

Dismantling of ACSR conductors of any description,stacking serviceable conductor aside for reuse and removing unsv/broken conductor complete all as specified and directed.

Taking down down/dismantling old/broken stay assembly complete including demolition of concrete, etc. and excavation complete all as specified and directed.

Dismantling /taking down old rusted /broken GI earth wire from feeder or distributor span complete all as specified and directed.

M&L Mild steel cross arms, bracings, supports, clamps, and back plates fabricated from structural steel sections including nut, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed including preparation of surfaces and applying two coats of aluminium paint over a coat of red oxide primer complete all as specified and directed.

Fixing only mild steel cross arms, bracings, supports, clamps, and back plates obtained vide item N0- 7 here-in-bebore, including nut, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed including preparation of surfaces and applying two coats of aluminium paint over a coat of red oxide primer complete all as specified and directed.

M&L for aluminium conductor,steel reinforced (ACSR) of any size, stringing properly on insulators on pole and binding with aluminium tape / binding with conductors, jumpers etc including dismantling and taking down old unserviceable ACSR conductor complete all as specified and directed.

M&L for Supplying, transporting, erecting in truely vertical steel tubular swaged poles type 410 SP-31 (9.0 metres long) complete with cast iron base plate, finial, taper plug, bolts,nuts and screws as specified, including necessary excavation and earth work, PCC 1:4:8 type D2 in foundations below pole, PCC 1:3:6 type C1 as in plinth block and coping, disposal of surplus soil to a distance not exceeding 50m and depositing where directed, painting of exposed surface of steel tubular poles with two coats of Aluminium paint over one coat of red oxide primer and providing 300 mm wide bands (3 bands/ straps with synthetic enamel paint and 2 bands with Black bituminous paint) from plinth block and numbering of poles, painting embedded portion of poles with one coat of bituminous paint complete all as specified and directed.

Restringing of LT overhead lines comprising ACSR conductors of any size from 04 conductors to 07 conductors after opening from insulators, including restringing same and winding on insulator with proper size of binding wire upto permissible sag complete all as specified and directed.

Restringing of LT overhead lines comprising ACSR conductors of any size From 08 conductors to 10 conductors after opening from insulators, including restringing same and winding on insulator with proper size of binding wire upto permissible sag complete all as specified and directed.

S&F (in repairs) guarding Cradles, hexagonal/ rectangular,fabricated with galvanised steel wire 4 mm dia on LT pole including binding with 14SWG MS wire complete all as specified and directed.

S&F (in repair) Insulator Pin type, povrcelain, vitreous, white, brown or green, insulator including one galvanised mild steel spindle, two galvanised iron washres and one glavanised iron nut, 100 mm height, 65 mm die. For 1100 volts grade complete all as specified and directed.

S&L in repair of shackle type Insulator porcelain vitreous white/ brown or green, 75 mm high and 90mm dia suitable for working pressure of 1100 Volt including Galvanized iron straps of size (31x3) mm ,nut, bolt of dia 12 mm and washers of suitable size, complete all as specified and directed.

S&F (in repairs) Stay Assembly comprising of 7/2.24mm galvanised MS stranded wire of rquired length fixed to pole with and including flat iron clamps fabricated out of 50x6mm flat iron and nuts,bolts & washers of suitable size, 40cms long 14mm dia galvanised MS stay bow, 215cms long 20mm dia stay rod with threaded end including bolts & washers, MS stay plate galvanised 230x230x6mm, two thimbles,loop type insulator of size 65x90mm with clearance dia of hole 20mm including necessary excavation, earth work and PCC 1:4:8 type D2 using 40mm stone aggregate complete all as specified and directed.

S&F ACB, 4 pole manual fixed, 415 volts, 50Hz, breaking capacity 50KA capacity 800A 1 No with micro processor release, adjustable over load, short circuit and earth fault settings in existing LT panel including taking out old u/s ACB from main panel duly disconnecting LT cables and reconnecting with new ACB, including testing & commissioning complete all as specified and directed by Engr-in-charge. Cat Part No.SL955810 DMX3 2500 of make Legrand or equivalent in ABB/Schneider

Reparing and servicing of ACB,4 pole manual fixed, 415 volts, 50Hz, breaking capacity 50KA capacity 800A 1 No with micro processor release, adjustable over load, short circuit and earth fault settings in existing LT panel including taking out old u/s ACB part duly disconnecting LT cables and reconnecting after replacemnt of any u/s part, including testing & commissioning complete all as specified and directed . Cat Part No. SL955810 DMX3 2500 of make Legrand

M&L for connecting service cable 2 core 10 sqmm 1100 volts grade heavy duty flat or circular PVC insulated aluminum multistranded conductor served with inner sheathing of PVC and overall PVC sheathed on service connection suspended by insulated hangers not more than 1 mtr apart including 4mm dia suspended GI wire complete all as specified and directed.

Taking down U/s service cable any size from wall/poles complete after disconnection all as specified and directed

Excavation in trenches not exceeding 1.5 Mtr wide and not exceeding 1.5 Mtr depth in soft / loose soil and getting out for removing / laying of pipe /Cables etc complete all as specified.

Returning, filling in , including spreading, levelling, watering and well ramming in layer not exceeding 25 cm thick in soft/oose soil complete all as specified and directed.

Removing excavated material (soil) not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the strating point complete all as specified and directed.

M&L for river sand, washed and screened dry for cushioning to under ground cable in tenches below and around under ground cable including spreading and levelling complete as specified and directed.

M&L laying well burnt old size bricks, sub calss "B" bricks, straight or curved on plan, laid flat with width equal to length of brick, laid dry over electric cablefor protection all complete all as specified and directed.

M&L for Boring/Drilling (Horizontally) manually/mechanically under existing road (Maximum 10 M in width) suitable for passing GI tubing of 40 to 80 mm bore complete all as specified and directed.

Taking down old u/s LT UG Cables of any size from trenches/poles/walls complete after disconnection all as specified and directed

M&L for Supplying, laying or fixing, jointing and testing LT under ground electric power cable Crossed linked polyethylene (XLPE Cable) insulated, galvanised steel strip or wire armoured, ISI-7098 Mark, with aluminium conductor multi stranded, heavy duty 1100 Volts grade of following sizes, complete all as specified laid in trenches / laid under floor or fixed naked with walls/ on poles/ in ducts / in GI pipes etc. complete all as specified and directed. (Note :- Excavation, earth work, sand cushioning, protection bricks/ tiles / block, Clamps, nuts, Bolts, washres and pipe shall be measured and paid separately under relevant items).

10 Sq mm cross sectional area, 2 core.

16 Sq mm cross sectional area, 4 core.

25 Sq mm cross sectional area, 4 core.

35 Sq mm cross sectional area, 3.5 core.

50 Sq mm cross sectional area, 3½ core.

70 Sq mm cross sectional area, 3½ core.

95 Sq mm cross sectional area, 3½ core.

120 Sq mm cross sectional area, 3½ core.

150 Sq mm cross sectional area, 3½ core.

Supply and fixing of GI strip 32 x 6 mm fixed in ducts / on wall / in trenches / floors etc for earthing complete fixed to equipment / test point / earth electrode complete all as specified and directed

Trimming of tree branches touching to LT / HT OH lines not exceeding 30 cm girth, shrub, vegetation, bush and saplings at least upto 5.0 M from outer edge of ACSR including cleaning of road/path/fencing etc complete all as specified and directed.

M&L for painting of steel tubular swaged poles of LT over head line 9 M long complete including all MS chanel mounted/fixed with pole, earth protection & water pipe (if exists) with two coat of aluminium paint and providing 05 Nos bands/ straps with synthetic enamel paint (black and yellow 30 cm wide each) from top of plinth block and numbering of poles with white synthetic enamel paint on black circular background complete all as specified and directed.

M&L for painting to RCC pole 8.5/9.00 metre long after scrapping of old painted surfaces and applying two coats of cement based paint up to 1.20 metre height from ground level in 30 cm alternative black and yellow strips and remaining portion including MS frames like channel,clamps, angle, D-clamps etc with two coats of synthetic enamel paint of suitable colour complete all as specified and directed.

S&F in repairs Galvanised mild steel tubing, 'Light grade' of following bore complete with all fittings, laid in trenches/ under roads, drain , paths, fixed to poles/ walls with Mild steel clamps, bolts, nuts and washerws complete all as specified of the following bore (Note :- Excavation & Earth work shall be measrued and paid separately)

40 mm bore

50 mm bore

80 mm bore

M&L for line separator PVC type with clamp including fixing with overhead lines of multi conductor of ACSR as and where directed to prevent short circuiting of phase/neutral conductors mutually complete all as specified and directed of following ways:-

Line separator 2way

Line separator 3 way

Materials and Labour for Earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6.0 mm thick buried directly in ground vertically to a depth not less than 2.25 meter deep below ground level with top edge of the earth plate at a depth not less than 1.5M below normal ground level connected to GI wire 4mm by means of bolts, nuts check nuts and washers of galvanized steel and connected to main switch board or main control board as directed and including provision of concrete pit in PCC (1:3:6) type C1, pre-cast RCC (1:2:4) type B1 cover slab 54 cm x 54 cm x 5 cm (Reinforced with 8 mm dia. TMT bars @ 150 mm, center to center both ways) with one handle for lifting made out of 8 mm dia. MS bar, provision of funnel, wire mesh, 20 mm bore galvanized steel tubing (Medium grade) for watering, charcoal or coke and salt in alternate layers, 15 mm bore galvanized steel tubing light grade for protection of earth lead connection, necessary excavation and earth work in any type of soil and including necessary testing complete all as shown on electrical plate No 3 of SSR Part-I (2009) complete as specified and directed complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6mm thick buried directly in ground (earth pit not less than 2.25 metre below ground level) with top edge of the earth plate not less than 1.5 metre below ground level, connected to GI earth strip size of 32x6 mm by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of SSR Part I connected to earth test point all as specified or indicated including excavation and connected earth work, in soft/loose soil, removing soil upto 50m, PCC 1:3:6 type C1 as in pit, 20mm dia GI pipe medium grade for watering pipe, 40mm bore GI medium grade earth lead protection pipe, 50mm thick RCC 1:2:4 type B1 cover slab of earth pit reinforced with 8 mm dia TMT Bars @ 75mm C/C both ways and with handle made out of 12mm dia bars, funnel, strainer, alternate layer of charcoal dust and common salt and testing on completion, complete all as specified and directed.

M&L for PCC (1:3:6) type C1 using 20 mm graded aggregate as in foundations of Stay and filling of mass concrete complete all as specified. (For Transformer/panel Fencing Area/LT/HT poles/installation area)

Material and labour for painting of pole number using stensils of letter size 75mm height with white synthetic enamel paint over black background complete all as specified and directed.

Material and labour Thermoplastic Cable Junction Boxes IP66/67 "weather proof", for outdoor installation with knockouts for cable entry with terminals suitable for 10-16sqmm cable of Size 155 x 210 x 92 mm incl busbar mounted on insulator and MCB SP 6 Amps-1 No, including necessary civil works and connecting all incoming and outgoing wires with AL lugs of appropiate sizes and complete all as specified and directed . Make Cat No. KF1616G of Hensel or euivalent in syntex

Supply, install, testing & commissioning of LT panel board CPRI approved, outdoor type, factory made fabircated to CRCA sheet of 3.15 mm thickness, angle iron of size 40X40X6mm thick frame workand tee section (frame) of suitable size double door front/rear opening and locking arrangement, floor mounted on plateform of suitable size, Al bus bar chamber (enclosed) incl rust free spray painting with two coat of synthetic enamel paint over a coat of red oxide primer mounted on PCC blocks, fixed with grouted bold, nuts and washer and making complete connection in all recpects as diected by engr-in-charge comprising of following accessories:- BUS-BAR & INTERNAL CONNECTIONS: The bus-bars shall be made up of 04 Nos tinned alluminium 200 A rated, duly insulated with 1100 V grade standard colour coded PVC sleeves & rigidly mounted on suitable sized "F" class insulators of non-hygroscopic, non-combustible, all internal connections from main bus-bars to switch gears etc.

PROVISION FOR CABLE ENTRY : The provision for cable entry/exit shall be provided in the bottom for both incoming & out-going cables. INCOMING : MCCB 4 pole, 415 Volts, 320 Amps, 36 kA (Ics = 100% Icu) with thermal magnetic release, adjustable short circuit & adjustable overload setting incl electric connection complete -01 Nos OUTGOINGS : MCCBs with thermal magnetic release, adjustable short circuit & adjustable overload setting incl electric connection complete. MCCB 4 pole, 415 Volts, 250 Amps, 36 kA for out going -02 Nos MCCB 4 pole, 415 Volts, 125 Amps, 25 kA for out going -01 Nos MCB TPN 63A -01 Nos for street light 4P power contactor type MCX 02- 01 Nos Cat Prt No. CS97010 of L&T or equivalent in AMM/Schneider Austro time switch - 01 Nos Cat No. AUSTSO2AST00 of L&T or equivalent in AMM/Schneider

Supply, install, testing & commissioning of LT panel board CPRI approved, outdoor type, factory made fabircated to CRCA sheet of 3.15 mm thickness, angle iron of size 40X40X6mm thick frame work and tee section (frame) of suitable size double door front/rear opening and locking arrangement, floor mounted on plateform of suitable size, Al bus bar chamber (enclosed) incl rust free spray painting with two coat of synthetic enamel paint over a coat of red oxide primer mounted on PCC blocks, fixed with grouted bold, nuts and washer and making complete connection in all recpects as diected by engr-in-charge comprising of following accessories:- BUS-BAR & INTERNAL CONNECTIONS: The bus-bars shall be made up of 04 Nos tinned alluminium 200 A rated, duly insulated with 1100 V grade standard colour coded PVC sleeves & rigidly mounted on suitable sized "F" class insulators of non-hygroscopic, non-combustible, all internal connections from main bus-bars to switch gears etc.

PROVISION FOR CABLE ENTRY : The provision for cable entry/exit shall be provided in the bottom for both incoming & out-going cables. INCOMING : MCCB 4 pole, 415 Volts, 320 Amps, 36 kA (Ics = 100% Icu) with thermal magnetic release, adjustable short circuit & adjustable overload setting incl electric connection complete -01 Nos OUTGOINGS : MCCBs with thermal magnetic release, adjustable short circuit & adjustable overload setting incl electric connection complete. MCCB 4 pole, 415 Volts, 200 Amps, 36 kA for out going -02 Nos MCCB 4 pole, 415 Volts, 125 Amps, 25 kA for out going -01 Nos

Material & labour for carrying out repairs to the APFC Panels including servicing / replacing wornout nuts, bolts, cable lugs, connecting wires, markers, insulating sleeves, repairs to PCC foundation etc and repacement of power capacitors with equal or higher capacities, capacitor switching duty contactor, suitable APFC Relay, HRC Fuse links etc all as directed including reinstallation at original or at a new location all as directed. (Repacement of power capacitor, capacitor switching duty contactor and APFC Relay, HRC Fuse links will be measured separately but cost for the the rest items required to make the APFC controller functional to achieve best result should deem to be included in the rate).

Supply and fixing Power factor correction Capacitor heavy duty of following capacities of Make:- L&T or equivalent in shneider/ABB

10 KVAR, Type LTCCR.

12.5 KVAR, Type LTCCR.

15 KVAR, Type LTCCR.

25 KVAR, Type LTCCR.

Supply and fixing 3 Ø 415 V 50 HZ Capacitor switching duty contactor suitable upto 25KVAR rating of type MO C 20, Cat N: CS90021 of L&T or equivalent in ABB/ Shneider.

Supply and fixing 3 Ø 415 V 50 HZ Capacitor switching duty contactor suitable upto 25KVAR rating of type MO C 25, Cat N: CS90021 of L&T or equivalent in ABB/ Shneider.

Supply and fixing of three connector switch suitable MNX 45/40 rating of type MO C 20, Cat N: CS94190 of L&T or equivalent in ABB/ Shneider.

Supply and fixing of three connector switch suitable MNX 25 rating of type MO C 20, Cat N: CS94110 of L&T or equivalent in ABB/ Shneider.

S & F in replacement of DIN type fuse links 100kA type HN size 00 of rated capacity 100A complete all as specified and directed. Cat N: SF94030 of L&T or equivalent in ABB/ Shneider.

S & F in replacement of DIN type fuse links 100kA type HN size 00 of rated capacity 125A complete all as specified and directed. Cat N: SF94030 of L&T or equivalent in ABB/ Shneider.

S & F in replacement of fuse holders & fuse bases suitable for cylindrial/DIN fuse-links of rating 63-160 A complete all as specified and directed. Cat N: SK90405 of L&T or equivalent in ABB/ Shneider.

S & F in replacement of Automatic power factor controller of suitable suitable for Banks upto 8 steps size 144x144 with 1/3 CT input having auto programming function complete all as specified and directed. Cat N: CS916140000 of L&T or equivalent in ABB/ Shneider.

Digital Panel mounted 3 phase LED Volmeter Meter suitable for measuring Volatge class 1.0 size as per site requirement, etc. Make:- L&T or Equivalent in Shneider/ABB.

Digital Panel mounted 3 phase LED Ameter Meter suitable for measuring Volatge class 1.0 size as per site requirement, etc. Make:- L&T or Equivalent in Shneider/ABB.

CT for measuring AC on LT 3 phase system, 1.1 kv grade, single burden, general purpose, of CT ratio as per site requirement.

LED Indicator Lamps for phases including holders and of colours red / yellow / green / blue etc.

S & F in replacement of MCCB 415 volt, AC 50 Hz, 3 pole, 25 KA with adjustable thermal and magnetic tripping system against over load and short circuit conditions of capacity 200 Amps including extended ROM all specification as per site sample. Make; L&T or equivalant in Legrand/ABB

S & F in replacement of MCCB 415 volt, AC 50 Hz, 3 pole, 50 KA with adjustable thermal and magnetic tripping system against over load and short circuit conditions of capacity 250 Amps including extended ROM all specification as per site sample. Make; L&T or equivalant in Legrand/ABB

S & F in replacement of MCCB 415 volt, AC 50 Hz, 3 pole, 36 KA with adjustable thermal and magnetic tripping system against over load and short circuit conditions of capacity 400 Amps including extended ROM all specification as per site sample. Make; L&T or equivalant in Legrand/ABB

S & F in replacement of MCCB 415 volt, AC 50 Hz, 4 pole, 36 KA with adjustable thermal and magnetic tripping system against over load and short circuit conditions of capacity 250 Amps. Make: L&T or equivalant in Legrand/Schneider/ABB

S & F in replacement of MCCB 415 volt, AC 50 Hz, 4 pole, 50 KA with adjustable thermal and magnetic tripping system against over load and short circuit conditions of capacity 400 Amps. Make: L&T or equivalant in Legrand/Schneider/ABB

Dismantaling & taking down unserviceable street light fittings LED Fittings/ CFL Fittings, Pin /Holder type/u/s flood light from pole or from Bldgs for repairs including replacement of unserviceable Lamp, holder, integral wiring with appropriate gauge copper conductor and refixing the same after repairs in original position properly using PVC insulation tape or where directed complete including replacement of any spares,cable connections from OH conductors, or from junction boxes to light fitting complete all as specified and as directed. Note : Spares items such as LED driver and cable etc, will be measured and paid separately under respective items.

Supply & Fixing in replacement of the following spare parts in street lights :-

PVC insulated weather proof sheated alluminium cable 2.5 Sqmm 2 core with 2.5 Sqmm single core for earting complete all as specified and directed.

LED Driver 25 Watt of Make Bajaj/Equivalent

LED Driver 30/35 Watt of Make Bajaj/Equivalent

LED Driver 45 Watt of Make Bajaj/Equivalent

LED Driver 60 Watt of Make Bajaj/Equivalent

Supply and Fixing in replacement New generation energy saving & environmental friendly long life Versatile pressure die-cast aluminium IP66 roadway luminaire with high power LEDs as light source with secondary optics & exclusively designed polycarbonate cover alongwith electronic driver suitable for upto 40 mm dia bracket size of rating 25 W LED including connecting with 2 core aluminium conductor 2.5 Sqmm & single core aluminium conductor 2.5 Sqmm for earthing with Overhead conductors or UG Cables on LT poles/wall complete all as specified and directed. Cat no ENDURAPEARLSL25WLED757SASYTOPCMP of Havells or equivalent of Bajaj/Simoco Note:- i) 5 years manufacturer's Warranty and test certificate shall be provided for LED fittings. (ii) Driver and luminaire shall be of same make

Supply and Fixing in replacement New generation energy saving & environmental friendly long life Versatile pressure die-cast aluminium IP66 roadway luminaire with high power LEDs as light source with secondary optics & exclusively designed polycarbonate cover alongwith electronic driver suitable for upto 40 mm dia bracket size of rating 35 W LED including connecting with 2 core aluminium conductor 2.5 Sqmm & single core aluminium conductor 2.5 Sqmm for earthing with Overhead conductors or UG Cables on LT poles complete all as specified and directed. Cat no ENDURACITYLITEPLATPLUSSL35WLED757SASYBOPC of Havells or equivalent of Bajaj/Simoco Note:- i) 5 years manufacturer's Warranty and test certificate shall be provided for LED fittings. (ii) Driver and luminaire shall be of same make

Supply and Fixing in replacement New generation energy saving & environmental friendly long life Versatile pressure die-cast aluminium IP65 roadway luminaire with high power LEDs as light source with secondary optics & exclusively designed polycarbonate cover alongwith electronic driver suitable for 40 mm dia bracket size of rating 45 W LED including connecting with 2 core aluminium conductor 2.5 Sqmm & single core aluminium conductor 2.5 Sqmm for earthing with Overhead conductors or UG Cables on LT poles complete all as specified and directed Cat no ENDURAPEARLNEOSL45WLED757PASYTOPC of Havells or equivalent of Bajaj/CG Note:- i) 5 years manufacturer's Warranty and test certificate shall be provided for LED fittings. (ii) Driver and luminaire shall be of same make

Supply and Fixing in replacement New generation energy saving & environmental friendly long life Versatile pressure die-cast aluminium IP65 roadway luminaire with high power LEDs as light source with secondary optics & exclusively designed polycarbonate cover alongwith electronic driver suitable for 40 mm dia bracket size of rating 60 W LED including connecting with 3 core aluminium conducor 2.5 Sqmm with Overhead conductors or UG Cables on LT poles complete all as specified and directed. Cat no ENDURAPEARLNEOSL60WLED757SASYTOPC of Havells or equivalent of Bajaj/Simoco Note:- i) 5 years manufacturer's Warranty and test certificate shall be provided for LED fittings. (ii) Driver and luminaire shall be of same make

Supply and Fixing in replacement new generation energy saving round type led high bay light 150W, environmental friendly & roboust highbay/mediumbay IP65 luminaire with high efficacy ith PDC housing for foxing to ceiling surface/suspebded mounting with system to be fixed to ceiling/channels with the existing wire/cable complete all as specified and directed. Cat no SAUCERPLUSBP150WLED85790DTOLTG of Havells or equivalent of Bajaj/CG Note:- i) 3 years manufacturer's Warranty and test certificate shall be provided for LED fittings. (ii) Driver and luminaire shall be of same make

Supply and Fixing in replacement new generation energy saving & environmental friendly long life versatile pressure die-cast aluminium IP65 flood luminaire with high power LEDs as light source with secondary optics & exclusively designed polycarbonate cover along with electronic driver of rating 150W LED Flood light including connecting with 2 core aluminium conductor 2.5 Sqmm & single core aluminium conductor 2.5 Sqmm for earthing with Overhead conductors/UG Cables/Junction box complete all as specified and directed. Cat no. JETAIRISFLS150WLED757PSYMLTG of Havells or equivalent of Bajaj/CG Note:- i) 5 years manufacturer's Warranty and test certificate shall be provided for LED fittings. (ii) Driver and luminaire shall be of same make

M&L for street light bracket made out of 32 mm dia GI pipe medium grade 120 cm long cut to size and bend to shape , fixing for LT steel poles with flat iron clamps 40mm x 6 mm – 02 sets including nuts, bolts and washers including one coat of aluminium pait over acoat of red oxide primer including taking down of old unserviceable complete all as specified.

M & L for street light bracket made out of 32 mm dia with two numbers GI pipe medium grade 120 cm long cut to size and bend to shape, fixing for LT steel poles with flat iron clamps 40mm x 6 mm – 04 sets for fixing two numbers LED light including nuts, bolts and washers including one coat of aluminium pait over a coat of red oxide primer including taking down of old unserviceable complete all as specified.

M&L for street light bracket made out of 32 mm dia GI pipe medium grade 120 cm long cut to size and bend to shape , fixing for RCC LT poles with flat iron clamps 40mm x 6 mm – 02 sets including nuts, bolts and washers including one coat of aluminium pait over acoat of red oxide primer including taking down of old unserviceable complete all as specified.

M&L for street light bracket made out of 32 mm dia with two GI pipe medium grade 120 cm long cut to size and bend to shape, fixing for RCC LT poles with flat iron clamps 40mm x 6 mm – 04 sets for fixing two numbers LED light including nuts, bolts and washers including one coat of aluminium pait over a coat of red oxide primer including taking down of old unserviceable complete all as specified.

Material and labour for replacement of junction boxes with new Thermoplastic Cable Junction Boxes IP66/67 "weather proof" , for outdoor installation with knockouts for cable entry with terminals suitable for 10-16sqmm cable off Size 155 X 210 X 92 mm incl busbar fixed in repairs and including Necessary civil works and connecting all incoming and outgoing wires with AL lugs of appropiate sizes and complete all as specified and directed . Make Cat No. KF1616G of Hensel or euivalent

Material & Labour for fabrication of Sheet metal enclosure, powder coated of Timelite Distribution Boards for automatic Switching of street lights internally pre wired by using suitable copper lugs including fixing with MS Clamp 40X5 mm to steel/RCC poles incl connection consisting of the following: (i) ASTRONOMICAL time switch 24 hrs operation 240 Volts Cat Part No.AUTS02AST00 of L&T or Equivalent of Legrand/Scneider (ii) 3 pole contactor 40Amps Cat Part No.Cat No. CS 94190 of L&T (iii) MCB FP 32 Amps Cat Part No. Cat No. BB40320C of L&T or Equivalent in Legrand/Schneider

Supply and fixing as in replacement of Time Switch, Digital control,Astronomical type suitable for daily operation in 230 volts AC supply make :-AUTS02AST00 of L&T

Supply and fixing as in replacement of three pole power contactor with control relay with AC Coil suitable for operation in 415 volts AC supplywith 230 volt relay coil and current rating 40Amps. Make: Cat No. CS 94190 of L&T or Equivalent in Legrand/Schneider

Supply and fixing as in replacement of MCB FP 32A 'C' Type for operation in 230/415 volts AC supply. Make:Cat No. BB40320C of L&T or Equivalent in Legrand/Schneider

Material and Labour in replacement for path light LED bollard 10W in cylindrical shape with opal acrylic diffuser and IP 65 & IK-10 protection with silent observer and giving light, diffuser at the upper portion acts a beacon of path guidance in a landscape enironment fixed on PCC 1:4:8 type D2 40mm graded all as specified and directed. Cat Prt No. Twister LBLTW-10-WW of Crompton or equivalent Make- Philips /Wipro/Crompton/GE Note:- i) 5 years manufacturer's Warranty and test certificate shall be provided for LED fittings. (ii) Driver and luminaire shall be of same make

S & F LED Post Top Lantern of new generation, energy, saving, environmental friendly, long life aesthetically designed with symmetrical light distribution, spun aluminium landscape Luminaris with high power LEDs as light source of 25 Watt LED including fixing on 40 mm dia grouted post complete all as specified and directed. Cat no.RUBYPT25WLED757PSYMTOPC of Havells or equivalent Make- Phillips / Crompton/Wipro/Eveready/GE Note:- i) 5 years manufacturer's Warranty and test certificate shall be provided for LED fittings. (ii) Driver and luminaire shall be of same make

Taking down LT UG Cables of any size from trenches/poles complete after disconnection all as specified and directed.

Material and labour for sand cushioning for cable protection using clean dry sand complete all as specified and directed.

D G Corporation

Anil Kumar Sarmah

M/S Inder SINGH SABARWALL

M/S SAKTI PADA DEY