Development of park(Green Space) at Surpura Dam, Jodhpur

Amount

Supply & Planting of the Trees/plants as specified, transportation to the site, excavation of pits of size 0.9 x 0.9 x 0.9 m for trees/plants. Filling pits with prepared manure soil (ratio 1 sludge plus 2 good earth by vol.) supply, transportation and mixing of soil with improvement nutrient including manure as required and inside coat of aldrin or equivalent in all pits, flooding with water, dressing including removal of rubbish and surplus earth if any with all leads and lifts, planting and stacking in full and final location including all locations specified. Botanical Name (Common Name) (Tree Code)

Cassia fistula (Amaltas) (AM) (Min. Ht. 10 Feet)

Phyllanthus emblica (Amla) (AL) (Min. Ht. 7 Feet)

Terminalia balerica (Bahera) (BA) (Min. Ht. 5 Feet)

Ehretia laevis (Chamrod) (CR) (Min. Ht. 5 Feet)

Anogeissus pendula (Dhau) (DU) (Min. Ht. 5 Feet)

Diospyros malabarica (Gaab) (GA)

Albizza lebbek (Indian siris) (IS) (Min. Ht. 10 Feet)

Millingtonia hortensis (Indian crok tree) (ICT) (Min. Ht. 10 Feet)

Syzygium cumini (Jamun) (JM) (Min. Ht. 10 Feet)

Madhuca longifolia (Mava/mahua) (MU) (Min. Ht. 10 Feet)

Morus indica/laevigata (Mulberry/tut) (TU) (Min. Ht. 5 Feet)

Pongamia pinnata (Karanjh) (KAR) (Min. Ht. 10 Feet)

Manilkara hexandra (Khirni) (Ki) (Min. Ht. 5 Feet)

Techomella undulata (Rohida) (ROH) (Min. Ht. 5 Feet)

Tamaridus indica (Tamarind) (TM) (Min. Ht. 5 Feet)

Polyathia longifolia (Ashok) (AK) (Min. Ht. 10 Feet)

Vachellia nilotica subsp. (Indica Babool) (BL) (Min. Ht. 5 Feet)

Agele marmelos (Bel) (BEL) (Min. Ht. 5 Feet)

Ziziphus mauritiana (Ber) (B) (Min. Ht. 5 Feet)

Populus euphratica (Bhani) (BH) (Min. Ht. 1 Feet)

Ehretia laevis (Chamror) (CH) (Min. Ht. 3 Feet)

Delonix regia (Gulmohar) (GM) (Min. Ht. 10 Feet)

Cordia sinesis (Gundi) (GN) (Min. Ht. 10 Feet)

Ficus carica (injeer) (IN) (Min. Ht. 5 Feet)

Olea europaea (Jaitun) (JA)(Min. Ht. 2 Feet)

Bauhinia malabarica (Kachnar) (KC) (Min. Ht. 10 Feet)

Thevetia peruviana (Kaner/yellow oleande) (YO) (Min. Ht. 5 Feet)

Bauhinia purpurea (Kanair) (K) (Min. Ht. 10 Feet)

Salvadora oleoids (Kharojaal) (KJ) (Min. Ht. 7 Feet)

Cordia myxa (Lasura) (LS) (Min. Ht. 5 Feet)

Mimusops elengi (Maulsari) (MS) (Min. Ht. 10 Feet)

Butea monosperma (Palaash) (PA) (Min. Ht. 5 Feet)

Acacia Fernasiana (Sweet acasia) (SA) (Min. Ht. 3 Feet)

Sambhaloo (SM) (Min. Ht. 10 Feet)

Phoenix Sylvestris (Wild Date Palm) (DP) (Min. Ht. 10 Feet)

Azadirachta indica (Neem) (NM) (Min. Ht. 10 Feet)

Ficus virens (Pilkhan) (PIL) (Min. Ht. 10 Feet)

Bombax Malabaricum (Simal) (SI) (Min. Ht. 10 Feet)

Acacia leucophloea (Ronjh) (RH) (Min. Ht. 5 Feet)

Anthosaphalus cadamba (Kadambh) (KD) (Min. Ht. 10 Feet)

Supply & Planting of the Shrubs as specified, transportation to the site, excavation of pits of size 0.6 x 0.6 x 0.6 m for Shrubs. Filling pits with prepared manure soil (ratio 1 sludge plus 2 good earth by vol.) supply, transportation and mixing of soil with improvement nutrient including manure as required and inside coat of aldrin or equivalent in all pits, flooding with water, dressing including removal of rubbish and surplus earth if any with all leads and lifts, planting and stacking in full and final location including all locations specified. Botanical Name (Common Name) (Shrub Code)

Plumeria rubra (PR) (Min. Ht. 7 Feet)

Plumeria alba (PA) (Min. Ht. 10 Feet)

Plumeria obtusa (PO) (Min. Ht. 5 Feet)

Ehretia laevis (Chamror) (CH) (Min. Ht. 3 Feet)

Bauhinia malabarica (Kachnar) (KC) (Min. Ht. 10 Feet)

Thevetia peruviana (Kaner/yellow oleande) (YO) (Min. Ht. 5 Feet)

Bauhinia purpurea (Kanair) (K) (Min. Ht. 10 Feet)

Hibiscus (Gudhal) (GL) (Min. Ht. 3 Feet)

Allamanda Angustifolia (Almanda) (AL) (Min. Ht. 2 Feet)

Gardenia jasminoides (Gandhraj) (GD) (Min. Ht. 3 Feet)

Allamanda Angustifolia (Almanda) (AL) (Min. Ht. 2 Feet)

Ziziphus Mauritiana (Beri) (BE) (Min. Ht. 5 Feet)

Citrus decumana (Chakotra) (CH) (Min. Ht. 5 Feet)

Hibiscus (Gudhal) (GL) (Min. Ht. 3 Feet)

Commiphora wightii (Guggal) (GU) (Min. Ht. 5 Feet)

Jatropha (Jatropha) (JT) (Min. Ht. 5 Feet)

Bauhinia racemosa (Jhinja) (Jhi) (Min. Ht. 3 Feet)

Prosopis cineria (Jhand) (JN) (Min. Ht. 2 Feet)

Capparis decidua (Kair) (KR) (Min. Ht. 1 Feet)

Carissa Carandas (Karonda) (KAR) (Min. Ht. 5 Feet)

Salvadora Persica (Peelu) (PE) (Min. Ht. 2 Feet)

Plumeria rubra (PR) (Min. Ht. 7 Feet)

Plumeria alba (PA) (Min. Ht. 10 Feet)

Plumeria obtusa (PO) (Min. Ht. 5 Feet)

Gardenia jasminoides (Gandhraj) (GD) (Min. Ht. 3 Feet)

Bouganvillea glabra (Bouganville) (BV) (Min. Ht. 2 Feet)

Supply & Planting of the Climbers as specified, transportation to the site, excavation of pits of size 0.30m in depth for Climbers. Filling pits with prepared manure soil (ratio 1 sludge plus 2 good earth by vol.) supply, transportation and mixing of soil with improvement nutrient including manure as required and inside coat of aldrin or equivalent in all pits, flooding with water, dressing including removal of rubbish and surplus earth if any with all leads and lifts, planting and stacking in full and final location including all locations specified. Botanical Name (Common Name) (Climber Code)

Cestrum nocturnum (Raat ki Rani/ Night blooming jasmine) (Min. Ht. 2.5 Feet)

Jasminum (Chameli/ Jasmine) (Min. Ht. 2 Feet)

Ixora sp. (Rukmini) (Min. Ht. 2 Feet)

Gardenia (Gandhraj) (Min. Ht. 1 Feet)

Jasminum auriculatum (Juhi) (Min. Ht. 1 Feet)

Murraya paniculata (Kamini/ Orange jesamine) (Min. Ht. 0.5 Feet)

Lawsonia inermis (Mehndi) (Min. Ht. 0.5 Feet)

Tabernaemontana (Chandni) (Min. Ht. 0.5 Feet)

Salvia splendens (Scarlet sage) (Min. Ht. 1 Feet)

Tagetes patula (Mexican marigold) (Min. Ht. 1 Feet)

Zinnia angustifolia (creeping zinnia) (Min. Ht. 0.5 Feet)

Ruellia patula (Kakori booti/ desert petunia) (Min. Ht. 0.5 Feet)

Drimia Indica (Jungli pyaz/ Indian squill) (Min. Ht. 1 Feet)

Verbascum chinenses (geedar tambaku/ chinese mullein) (Min. Ht. 0.5 Feet)

phyla nudiflora (jalbooti/ frog fruit) (Min. Ht. 0.5 Feet)

Supply & Planting of the Hedges as specified, transportation to the site, excavation of pits of size 0.30m in depth for Hedges. Filling pits with prepared manure soil (ratio 1 sludge plus 2 good earth by vol.) supply, transportation and mixing of soil with improvement nutrient including manure as required and inside coat of aldrin or equivalent in all pits, flooding with water, dressing including removal of rubbish and surplus earth if any with all leads and lifts, planting and stacking in full and final location including all locations specified. Botanical Name (Common Name) (Hedge Code)

Clerodendron Inermi

Duranta Repens dew drops

Gendrarussa vulgaris

Supply of Greennet (75%) width of 150 cm at site with installation of 3" dia balli/pipe including loading & unloading of material

Supply of Irrigation Hardware Providing, and fixing uPVC Pipe confirming to IS:4985:2000 and suitable for the respective working pressures with all fittings & trenching & backfilling Accessories like PVC Elbow, Bend, Tee, solution, Reducer Etc. Laying of pipes, sprinklers, Drip lines, Valves, Cables, Pump station and any other required fixture to complete the system and make it operational (Civil Work not include) Pipe Make : Supreme Finolex, Astral etc.

PVC Pipe 110 mm x 6 Kg/cm2

PVC Pipe 90 mm x 6 Kg/cm2

PVC Pipe 63 mm x 6 Kg/ cm2

PVC Pipe 40 mm x 6 Kg/ cm2

Providing, Supplying and Fixing of Pop Up Sprinkler with Rain Curtain Nozzle, Adjustable Arc, Clear 4 inch Pop up with Nozzle. Pop up Should be water lubricated gear driven with three years warranty, Radius of Pop up should be 14 Mtr. to 19 Mtrs with 1" BSP threaded inlet, SAM Check Valve, Nozzle outlet trajectory is 25 Degree and exposed surface diameter should be 2 inch only. Make of Pop Up : Falcon 6504 Make: Rainbird, Toro, Nelson etc.

Providing, Supplying and Fixing Swing Joint Should be unique Swept Elbow for optimize rotor performance, Pressure rating of Swing Joint should be 315 PSI, Design of elbow should be as per international standard to reduce pressure loss, Double O-ring provide Extra protection against any leaks. Size : 1" with Three Elbow. Make : Rainbird, Dura etc.

Providing, Supplying and Fixing P.P. Clamp Should be High Industrial grade Material and should be tested at 10 Bar Pressure, Nutbolt should be cromed, O ring should be NBR material grade with sizes of 90, 75, 63, 50 and 40 mm in 1" Sizes Make : Gf+. Astore-Italy. FIP etc.

Providing, Supplying and Fixing Filtration unit semi automized should be Disc type 130 micron and Capacity of Filter should be 50000 ltr/ Hrs Make should be : Amiad, Filtromat, Arkal etc.

Providing, Supplying and Fixing PVC Ball Valve Should be PN 16, Size should be 63 mm, Double Union for easy maintenance Make : Gf+. Astore-Italy. FIP etc.

Providing, Supplying and Fixing 10" Round Valve Box with green Top with Unique pipe hole knock outs provide faster and easy installation, Valve box should be locable arrangement, Dimension of Valve Box- 10.25 inch x 10" Height, 13.75 inch Bottom Diameter Make : Rainbird, Karson etc.

Providing, Supplying and Fixing ¾" Bass Quick Coupling valve with MS Saddle & Riser etc.

Providing, Supplying and Fixing ¾" Brass quick coupling valve key Approved Make

Providing, Supplying and Fixing Swivel Elbow Hose ¾" Approved Make

Providing, Supplying and Fixing Double Acting Continuous type air valve size 1" Make : ARI, Bermad etc.

Providing, Supplying and FixingPressure Relief Valve 2" Quick Type and immediate work if Pressure increase to 6 Bar. Pressure Relief Valve should be Bermad Approved Make

Providing, Supplying and Fixing Pressure Guage-Glycerin filled Approved Make

Providing, Supplying and Fixing Non Return Valve 6" Approved Make

Providing, Supplying and Fixing PVC Butterfly Valve Should be PN 16, Size should be 4" for easy maintenance Make : Astore-Italy. FIP etc.

Providing, Supplying and Fixing Round valve box 7" to 10" Make : Rainbird, Karson etc.

Providing, Supplying and Fixing PVC Butterfly Valve Should be PN 16, Size should be 160mm for easy maintenance Make : Astore-Italy. FIP etc.

Providing, Supplying and Fixing PVC Butterfly Valve Should be PN 16, Size should be 90mm for easy maintenance Make : Astore-Italy. FIP etc.

Supply & Installation of Solar street light (Including civil work as per attached drawing) – having MS powder coated body encases Solar PV panel poly-crystalline, comprising of Lithium battery with in-built BMS, high brightness LED light, driver efficiency more than 90%, High efficiency charge controller with automatic dimming functionality (with 12m PIR motion sensor) compliant to IP-65 automatic Dusk to Dawn operation, working temperature 0 C to 55C, with battery overcharging and battery deep discharging protection. Indications should include GREEN LED for battery charging and RED LED for battery low (one blink every 2 second) and Solar panel dirty indication (two blinks every 2 second). Light should be properly packed in Litlon (1 inch thick or better) to avoid any damage during transit 12Watt LED Material: Aluminium Alloy Solar Panel: Monocrystalline, Max Power 18V/35W LED Power: Bridgelux 12W Battery : Li ion 14Ah Lumens : 1360 - 1560 , View angle- 120⁰ Install Height : 4 - 6m Charge time : 6 - 8 hours Discharge time : 8 - 12 hours Backup : 2 - 3 days warranty period : - One year onsite Warranty

Providing & Fixing of Rabbit Spring Rider Arihant's Model PGKD 23 or equivalent Product Area : 0.8m x 0.4m (2.6ft X 1.3ft) Safe Play Area : 1.8m x 1.4m (5.9ft X 4.6ft) Ideal For : 3-6 Years Friends at a time : 1 Rider Its required area 1.0 mtr x 0.8 mtr. Total height 0.5mtr from ground level. Leg support should be made by 40 mm IDGI pipe & handle made by 15 mm NB pipe. The typical Spring Rider is comprises of Flexible Spring & HDPE sheets of high quality. It‟s specially made for kids in between 3 to 8 yrs. It‟s designed specially keeping in mind growing kid‟s mental development aspects & safety aspects. Playing on this spring rider will enable the kids to develop coordination between force & balance which is required for proper mental development. It also enhances griping power of children which will in turn strengthen growing bones. The rest is only fun that‟s required for emotional development of a children.

Providing & Fixing of Double Swing Arihant's Model PGSW 04 or equivalent Product Area : 3m x 2.5m (10ft x 8.2ft) Safe Play Area : 4.2m X 2.5m (13ft X 11.5ft) Ideal For : 4-14 Years Friends at a time : 2 Its total required area 3 mtr. X 2.5 mtr. And height shall be 2.4 mtr. From ground level top bar of swing is made by 80mm IDGI pipe. And 4 nos. of leg support pipe should be 60mm IDGI pipe. Top bar attach with 2 nos. of alloy steel coasting bearing with GI chain. Seating arrangement of swing is made up of 10mm thick. Anti skid chequered reinforced rubber belt. Bearing should be covered by specially design nylon clamp. The pure polyester powder coating (oven baked) done on the pipes extend the life of equipments. And install by C.C. base system as per order by engineer in charge

Providing & Fixing of Elephant see-saw Arihant's Model PGSS 06 or equivalent Product Area : 0.4m X 0.75m (1.3ft X 2.4ft) Safe Play Area : 1.4m X2m (4.5ft X 6.5ft) Ideal For : 3-8 Years Friends at a time : 2 This innovative see saw is an exciting product, which provides unlimited fun to the children playing on it. The Elephant is made up of PP sheet of 12mm thick. The seating arrangement is also made up of FRP sheet of 3mm thk. The handles for gripping are made up of S.S material. The frame is made from 25 x 50 x 1.6 mm thk rectangular tube. Rubber padding is fixed at the bottom end of the tube to absorb the ground impact. The Elephant are mounted on a pair of heavy-duty compression spring. The dia of the spring rod is 20mm. The spring is mounted on 5mm thick plate. And the stand for support is made out of 50MM NB powder coated GI pipes. For a good foundation, M.S. angle of size 25 x 25 x 5 mm thk are provided. Special end caps are used to cover the nuts bolts so that no injury is caused to the child.

Providing & Fixing of Tiny See-Saw Arihant's Model PGSS 09 or equivalent Product Area : 1.3m x 0.5m (4.3ft X 1.6ft) Safe Play Area : 2.3m x 1.5m (7.5ft X 5ft) Ideal For : 1-3 Years Friends at a time : 2 This innovative spring see saw is an exciting product, which provides unlimited fun to the children playing on it. The seating arrangement is also made up of FRP sheet of 3mm thk. The handles for gripping are made up of S.S material. The frame is made from 25 x 50 x 1.6 mm thk rectangular tube. Rubber padding is fixed at the bottom end of the tube to absorb the ground impact. The dia of the spring rod is 20mm. The spring is mounted on 5mm thick plate. And the stand for support is made out of 80MM NB and leg support should be 50MM NB. powder coated GI pipes. For a good foundation, M.S. angle of size 25 x 25 x 5 mm thk are provided. Special end caps are used to cover the nuts bolts so that no injury is caused to the child.

Providing & Fixing of a Playset Arihant's Model Theme MAPS T19 or equivalent Product Area : 5m x 3.7m (16ft x 12.2ft) Safe Play Area : 7m x 5.6m (23ft x 18.3ft) Age Group : 2-5 yrs Friends at a time : 15 Platform Height : 3ft & 5ft (1)PLATFORM The platform is made in Fiber reinforced plastics with anti skid surface giving ,it is a smooth finish so that the child does not slip while walking on it . Each of the side should be 1.16 m x 1.16 m .The innovative Frog canopy and poll leaf at the top of the deck is made up of Fiberglass reinforced plastic which gives aesthetic look to the MPPS. (2).PLATFORM WITH CIRCULAR CANOPY (1.5 MTR) The platform is made in Fiber reinforced plastics with anti skid surface giving, it is a smooth finish so that the child does not slip while walking on it . Each of the side should be 1.16 m x 1.16 m .The innovative Frog canopy and poll leaf at the top of the deck is made up of Fiberglass reinforced plastic which gives aesthetic look to the MPPS. (3).FRP STAIRCASE The FRP staircase is made up of Fiber Reinforced plastic with a conservative thickness of 4 mm. Ladder should have Reinforcement to maintain strength and avoid bending. The top surface of the ladder should be such that it should not deserve any kind of skidde (4).WIDE STAIRCASE WITH RAILING :- The wide staircase is made up of Fiber reinforced plastic with thickness of 4 mm. The railling will be made from 20 NB GI pipe. The railling is attached to the deck with the help of 80 x 20 NB GI nylon clamps. The railing will be powder coated to avoid rusting. There is a FRP Lotus & SUNFLOWER is affixed to the deck pipe with the help of 20 NB GI pipe. (5). MINI WAVE SLIDE WITH SLIDE ENTRY ;- The centre support of the mini wave slide is made up of 50 NB GI pipe .The slide portion is made in glittering FRP material . The thickness of the mini wave slide is 4 mm with proper reinforcement to support the module; the landing support is made made up of 25 NB GI pipes. All the sharp edges and corners grinded to give smooth finish so that children are not hurt while playing the pure polyester powder coating done on the pipes extends the life of equipment . There is also FRP slide entry. (6). FROG RAILING :- The FRP Frog railing is provided for the deck for safety purpose And it is made of reinforced plastics. It is attached to the deck pipe with the help of 80 NB GI nylon clamps. The support pipe is powder coated to avoid rusting of the pipe. (7). DOUBLE WAVE SLIDE WITH SLIDE ENTRY :- The double wave slide chute with top entry module is made up of 4 mm thick fiber reinforced plastic with self pigment. The chute has its end such as it cause safe landing of the child. The landing portion is horizontal with respect to the ground. The landing support provided is made up of 25 NB GI pipe. (8). CROSS –N- ZERO :- This item provides brain washing experience to the children and enhances their technical strength by providing them an intelligent game. The prisms for the “x” and “o” of this item are made made out of molded plastics while the frame is made out from LLDPE in roto molded. The prisms are fixed on powder coated GI pipe frame of 20 NB GI and 15 NB GI pipes. The cross n zero attached to the deck pipe with the help of 80 NB nylon clamps. (9). BALL RAILING :- The ball for ball railing are made out of molded plastics (HDPE), While the frame of it is also made in Roto molding process. The ball is attached over 12 mm Dia rod to the frame. (10). FRP DOLPHIN /LOTUS/ SUNFLOWER / BUTTERFLY:- The dolphin is made from fiberglass reinforced plastics. The dolphin is mounted inside 20 NB GI pipe. The character is attached to etc. Complete as per directions of the engineer Incharge.

Providing & Fixing of a Playsets Arihant's Model Theme MAPS T22 or equivalent Product Area : 7.9m x 4.8m (26ft x 15.7ft) • Safe Play Area : 9.9m x 6.8m (32.5ft x 22.5ft) Age Group : 2-5 yrs Friends at a time : 15 Platform Height : 3ft & 5ft (1)PLATFORM The platform is made in Fiber reinforced plastics with anti skid surface giving ,it is a smooth finish so that the child does not slip while walking on it . Each of the side should be 1.16 m x 1.16 m .The innovative Frog canopy and poll leaf at the top of the deck is made up of Fiberglass reinforced plastic which gives aesthetic look to the MPPS. (2).PLATFORM WITH POLL LEAF (1.5 MTR) The platform is made in Fiber reinforced plastics with anti skid surface giving, it is a smooth finish so that the child does not slip while walking on it . Each of the side should be 1.16 m x 1.16 m .The innovative Frog canopy and poll leaf at the top of the deck is made up of Fiberglass reinforced plastic which gives aesthetic look to the MPPS. (3).FRP STAIRCASE The FRP staircase is made up of Fiber Reinforced plastic with a conservative thickness of 4 mm. Ladder should have Reinforcement to maintain strength and avoid bending. The top surface of the ladder should be such that it should not deserve any kind of skidde (4).WIDE STAIRCASE WITH RAILING :- The wide staircase is made up of Fiber reinforced plastic with thickness of 4 mm. The railling will be made from 20 NB GI pipe. The railling is attached to the deck with the help of 80 x 20 NB GI nylon clamps. The railing will be powder coated to avoid rusting. There is a FRP Lotus & SUNFLOWER is affixed to the deck pipe with the help of 20 NB GI pipe. (5). MINI WAVE SLIDE WITH SLIDE ENTRY ;- The centre support of the mini wave slide is made up of 50 NB GI pipe .The slide portion is made in glittering FRP material . The thickness of the mini wave slide is 4 mm with proper reinforcement to support the module; the landing support is made made up of 25 NB GI pipes. All the sharp edges and corners grinded to give smooth finish so that children are not hurt while playing the pure polyester powder coating done on the pipes extends the life of equipment . There is also FRP slide entry. (6). FROG RAILING :- The FRP Frog railing is provided for the deck for safety purpose And it is made of reinforced plastics. It is attached to the deck pipe with the help of 80 NB GI nylon clamps. The support pipe is powder coated to avoid rusting of the pipe. (7) SPIRAL SLIDE:- The spiral slide is made up of Fiber Reinforced Plastic (FRP) in one piece having shell thickness of 3-4 mm. The slide is supported on a center support 80 NB GI pipe. The landing supports of the slide are supported by two 20 NB pipes (8). CROSS –N- ZERO :- This item provides brain washing experience to the children and enhances their technical strength by providing them an intelligent game. The prisms for the “x” and “o” of this item are made made out of molded plastics while the frame is made out from LLDPE in roto molded. The prisms are fixed on powder coated GI pipe frame of 20 NB GI and 15 NB GI pipes. The cross n zero attached to the deck pipe with the help of 80 NB nylon clamps. (10). FRP DOLPHIN /LOTUS/ SUNFLOWER / BUTTERFLY:- The dolphin is made from fiberglass reinforced plastics. The dolphin is mounted inside 20 NB GI pipe. The character is attached to etc. Complete as per directions of the engineer Incharge.

Providing & Fixing of a Playset Arihant's Model ROTO MAPS R06 or equivalent Product Area : 8.2m x 5.6m (27ft x 18.4ft) Safe Play Area : 10.2m x 7.5m (33.4ft x 24.6ft) Age Group : 8-12 yrs Friends at a time : 15 Platform Height : 3ft & 5ft

Providing & Fixing a Playset Arihant's Model MAPS 03 or equivalent Product Area : 14m x 10m (46.5ft x 33ft) Safe Play Area : 16m x 12m (52.5ft x 39.2ft) Age Group : 5-7 yrs Friends at a time : 40 Platform Height : 3ft & 5ft & 7ft No. Description Qty 1 Sq. Deck 5‟ Ht with canopy 3 2. Sq. Deck 3‟ ht with canopy 1 3 FRP Bridge 8‟ Long 1 4 FRP Tunnel 6‟ Long 1 5 Swinging Bridge 1 6 Spiral Slide 5‟ Ht 1 7 FRP Ladder 5‟ Ht -115- 8 Rock Climber 5‟ ht 1 9 Wave Slide 5‟ ht 2 10 Chain Climber 5‟ ht 1 11 Bubble Panel 1 12 FRP Staircase 3‟ ht 1 13 Square Canopy 1 14 Cross n Zero 1 Sq. Deck 5‟ ht with canopy: The platform is made up of FRP with anti skid surface. The top canopy is made of FRP with a minimum thickness of 2-3 mm. The canopy is assembled from four modules. Bowl Slide 3‟ ht: The Bowl slide sliding part is made up of Fiber glass Reinforced Plastic molded one and is of attractive color and shade. The FRP bowl slide has minimum permissible joints suitable for children such that child does not fall down while sliding down. The thickness of the slide is 3 -4 mm thk. There is a suitable handgrip on the side of the slide. The landing support is made up of 25 NB GI pipes. FRP Bridge 8‟ Long: The FRP Bridge is made from FRP with a thickness of 4mm. The ladder should has strength and avoids bending. The ladder should be such that it does not have any kind of skiddy movement. FRP Tunnel 6‟ Long: FRP Tunnel is a pipe shaped module of specific dia made from FRP of 4mm thickness. Swinging Bridge 8‟ Long: The swinging bridge is made up of wooden planks attached together with the help of nuts bolts and is suspended with galvanized chains of 12mm thk. The railing is madefrom roto molding process with pipe support of 20 NB GI pipe. The frame is made up of 80 NB pipe & has a 50 x10 MS flat welded at the ground level. Spiral Slide 5‟ ht : The spiral slide chute is made of FRP having shell thickness of 5-6 mm. The center support of the spiral slide is made from 100 NB GI pipe. The supports for landing are made up of 20 NB GI pipe. The railing is made up of LLDPE in roto molding process. It is supported by 20 NB GI pipes. The support pipe is powder coated to avoid rusting of the pipe. FRP Ladder: FRP ladder is made up of FRP with a conservative thickness of 4 mm. The ladder has reinforcement to maintain strength and avoid bending. The top surface of the ladder should be such that it should not deserve any kind of skiddy movement. Rock Climber 5‟ ht: The Rock climber is made up of FRP (FRP). The rocks are moulded on same platform. The climber is supported by 25 NB pipe at the bottom for ground support. Wave Slide 5‟ ht: The Wave slide Chute with top entry module is made up of 4 mm thick of FRP. The Wave shape should be in such a manner that it will not give any jerk or bump to the rider. The chute has its end such as it causes safe landing of the child. The landing portion should be in horizontal with respect to the ground. There should be support provided made up of 25 NB GI pipe. Chain Climber: The chain climber is made from 7mm thick galvanized chain. The foundation frame is made from 25 NB GI pipe with „U‟ hooks welded to it. The chain is over-hanged with a M.S. flat 50 x 10 with the help of „U‟ hooks. The steps are made from 20 NB GI pipes welded to the chain for climbing. Bubble Panel: The bubble panel is provided for all decks for safety purpose and it is made up of LLDPE in rotomould process. It is supported by 20 NB GI pipes clamped to the vertical support pipe. The support pipe is powder coated to avoid rusting of the pipe. FRP Staircase 3‟ht: The staircase is made up of FRP with a conservative thickness of 4 mm. The ladder should have reinforcement to maintain strength and avoid bending. The top surface of the ladder should be such that it should not deserve any kind of skiddy movement. Cross n Zero: The cross n zero enhances the tactical strength ability of the children. The prisms of „X‟ and „O‟ are made out of molded plastic while the frame is made out from LLDPE in molding process. The prisms are fixed on powder coated GI pipe frame of 15 NB.

Providing & Fixing of Criss Cross Scrambler Arihant's Model PGDL 09 or equivalent Product Area : 1.7m X 1.7m (5.6ft X 5.6ft) Safe Play Area : 2.7m X2.7m (8.9ft X 8.9ft) Ideal For : 4-12 Years Friends at a time : 5-6

Providing & Fixing of A to B Scrambler Arihant's Model PGKD 04 or equivalent Product Area : 3.6m x 0.5m (11.8ft x 1.6ft) Safe Play Area : 4.6m x 1.5m (15ft x 5ft) Age Group : 3-8 yrs Friends at a time : 4-5 The frame of A to B climber consists of alphabet shape „A‟ and „B‟ which is made from 25 NB GI pipes. It has spacers of 20 NB GI pipes. It also consists of a ladder placed between„A‟ and „B‟ made from 20 and 25 NB GI pipes. The whole item is powder coated to avoid rusting of the pipes and for esthetic look.

Providing & Fixing of Toddler Swing Arihant's Model PGSW 08 or equivalent Product Area : 3.3m x 1.0m (10.8ft X3.3ft) Safe Play Area : 4.3m x 2.0m (14ft X6.6ft) Ideal For : 3-8 Years Friends at a time : 2 In the toddler swing the center support is made up of 100 NB GI pipes. The horizontal bars are made up of 60 NB powder coated GI pipes. The bucket seats of the toddler swing are made of rubber with anti skid. The ball bearings are mounted inside specially designed nylon balls. The rubber seat is affixed on 6mm thick GI chain. The seats are made with full care so that the child does not fall from it while swinging.

SKY WALKER • DIMENSIONS: - 1720mm (Length) x 630mm (Width) x 1750mm.(Height) • SAFE AREA: - 2.7Mtr x 1.6Mtr. • SkyWalker Equipment made from "C" class G.I. Pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters • The main frame pipe is of 80mm NB made from "C" Class G.I. Material which is bend at the radius of 250mm. • The leg movement frame is of 50 x 50mm x 3mm thick CRC square pipe. • Sleeves are made up of 100 mm OD M.S. pipe with thickness 5mm. This results in easy replacement of bearings, pins and handle. • The handle frame is of 25mm NB made from "C" Class G.I. pipe. • The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB "C" class. Welded with M.S. round plate of 0250mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. Two foundations are provided for rigid support. • The footrests made from Aluminum casting material of size 130 X 310 X Smm. • Closing Caps are made up of high quality Fiber reinforced Plastic material. • The pins used are made up of 0 25mm SAE8620 bright material. Pins are fixed at the outer end with M8 grub screws and Dia.8mm SS ball. • The bearings used are "6205zz" are permanent lubricated sealed bearing of reputed brand. • High tensile steel with galvanized nuts & bolts are used for assembly. • The cerclips used for assembly are of A24 type. • The powder coating is done with Pure Polyester powder of Ackzo n o bl e or Berger with 60 to 70 micron thickness.

LEG PRESS • DIMENSIONS: - 1840mm (Length) x 360mm (Width) x 1560mm. (Height). • SAFE AREA:- 2.8 x 1.4Mtr. • Leg Press equipment made from "C" Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters • The center pipe is of 100mm NB made from "C" Class G.I. pipe. • The Sleeve frame is of 100 OD and of M.S. Seamless Pipe with thickness 5mm. This sleeve can be disassembled from main frame. • The bottom support of M.S. round plate of 0250 mm & 10mm thick. • The remaining outer frame is of 32NB made from "C" class G.I. pipe. • The foundation used for fixing is structure and made from center pipe of G.I. of 80mm NB "C" class welded with M.S. round plate of 0250mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angle of 3 mm thickness and 20mm x 40mm CRC square pipe of 3mm thickness. • Seat & Back rest provided are made up of MS deep draw quantity of 2mm thickness with no joint with uniform outer edge radius 20mm. • The footrests are made from tasted Aluminum material, having sizes 130mm X 310mm X 5mm thick. With the support of 310mm X 130mm X 3mm thick MS plate. • The frame of footrests made up of 25 NB "C" class G.I. pipe. • Closing Caps are made up of high quality Fiber reinforced Plastic material. • To build structure bushes are used which are made from M . S . seamless pipe of 50mm O.D. and 5mm thickness. • The pins used are made up of 025 mm SAE 8620 bright material. • The bearings used are of "6205zz" permanent lubricated sealed bearing of reputed Brand. • High tensile steel with galvanized nut bolts are used for assembly. • The cerclips used for assembly are of A24 mm. • The powder coating done with Pure Polyester powder of Ackzo n o b le or Berger with 60 to 70 micron thickness.

ROWER • DIMENSIONS: - 1200mm (Length) x 1000mm (Width) x 920mm. (Height) • SAFE AREA: - 1.5Mtr. x 1.5Mtr. • Rower Equipment made from "C" Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters • The Main frame is of 80NB "C" class G.L. Pipe welded with M.S. round plate of 250mmX1Omm. • The handle frame 2 5 N B is made from "C" class G.I. pipe. • The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB "C" class Welded with M.S. round plate of 0250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. • To join the movement frame to main frame connecting links made up from 32 NB G.1. "C" class pipe. • The seat fitted on the outer frames are made up of M.S. Sheet of size 330 mm X 300mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. • Pins used of Diameter 17mm are made up from SAE 8620 bright material. • The bearings used are of "6203zz" permanent lubricated sealed bearing of reputed brand. • High tensile steel with galvanized nuts and bolts are used for assembly. • The P.U. bushes (Stopper) used to avoid the collision. • The circlips used for assembly is of A 16 • The powder coating done with Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness.

CROSS TRAINER • DIMENSIONS: - 1320mm (Length) x 600mm (Width) x 1750mm. (Height). • SAFE AREA: - 1.77 x 1.2Mtr. • Cross trainer equipment made from "C" Class G.I. Pipe of different N B. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters • The main frame Pipes are of 80NB "C" Class G.I. Pipe with single bend pipe with 250mm radius. • The bottom support of M.S. round plate of 0250 mm & 10mm thick. • The Handle Frame is made up of 25NB "C" Class G.I. Pipe. • The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB "C" class welded with M.S. round plate of 0250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. • To build structure bushes are used which are made from M . S . seamless pipe of 60mm OD. With 5 mm thickness. • The footrests a r e made from Aluminum casting material of size 130 mm X 310mmX5mm thickness and mounted on M.S. Plate of Size 130mmx310mmx3mm thick • Closing Caps are made up of high quality Fiber reinforced Plastic material. • Pins used o f Diameter 35mm, 25mm, and 17mm are made up from SAE 8620 bright . • T h e Bearings used are of "6007zz" "6205zz" and "6203zz" permanent lubricated sealed bearing of reputed brand. • High tensile steel with galvanized nuts and bolts are used for assembly. • T h e powder coating is done with Pure Polyester powders of Ackzonoble or Berger Paints with 60 to 70 Micron thickness. • A16 , A 24 mm circlips are used for assembly. • Bolt M8X16 mm and NY lock nut of M8 made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust.

POMMEL HORSE • DIMENSIONS: - 2150mm (Length) x 800mm (Width) x 800mm. (Height). • SAFE AREA: - 5Mtr x 3.5Mtr. • Pommel horse equipment made from "C" Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters • The main frame of 80NB and 5ONB made from "C" Class G.I. pipe. • The handle frame is of 32NB made from "C" Class G.I. pipe. • 40mm x 40mm CRC square pipes frame is placed on the 25mm x 25mm x3mm M.S. L Angle with 60 x 10m thickness flat is used for support. • Closing Caps are made up of high quality Fiber reinforced Plastic material. • High tensile steel with galvanized nuts and bolts are used for assembly. • The powder coating is done with PurePolyester powder Ackzonoble or Berger Paints with 60 to70 micron thickness.

SIT UP BOARD DOUBLE • PRODUCT DIMENSIONS: - 1760mm (Length) x 1140mm (Width) x 660mm (Height). • SAFE WORKOUT AREA: - 2500mm (Length) x 1600mm (Width). • The Sit up Board double made from "C" Class GI pipe. Center column made from 100mm NB "C" class G.I. Pipe. • The main frame is of 25mm NB made from "C" Class GI pipe. FRP sheet of 3mm thickness is molded on main frame. • The remaining frame of the sit up board is of 32mm NB made from "C" class GI pipe. • The powder coating is done with Pure Polyester powder Ackzonoble or Berger Paints with 60 to 70 micron thickness. • The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB "C" class Welded with M.S. round plate of 0250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness.

SEATING & STANDING TWISTER • DIMENSIONS: - 1700mm (Length) x 540mm (Width) x 1250mm. (Height). • SAFE AREA: - 3 Mtr x 1Mtr. • Seating &Standing Twister equipment made from "C" Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters • The Center Pipe is of 100mm NB made from "C" Class G.I. Round Pipe. • The M.S. round plate of 0250 mm & 10mm thickness is welded at bottom. • Handle and Bottom sleeve pipe of 125mm OD with thickness 5mm provided for easy assembly, replacement and maintenance. • The bottom frame of the Seating & Standing twister is of 32 NB, 50 NB, and 25 NB made from "C" class G.I. pipe. • The handle frame of Seating & Standing twister is 25 NB & Foot resting frame of seating side is made from "C" class G.I. pipe of 25mm NB. • The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB "C" class, Welded with M.S. round plate of 0250 mm& 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRCA square pipes of 3mm thickness. • The Twister plate fitted on the bottom frame is made up of M.S. Round Plate of size 300mm diameter and 10mm thickness. • Closing Caps are made up of high quality Fiber reinforced Plastic material. • The Pins used are made up of 0 35 mm SAE 8620 bright material. • The bearings used are of "6205zz" permanent lubricated sealed bearing of reputed brand. • High tensile steel with galvanized nuts & bolts are used for assembly. • The powder coating is done by Pure Polyester powder of Berger Paint with 60 to 70 micron thickness.

Seated Puller • DIMENSIONS: - 1900mm (Length) x 740mm (Width) x 1920mm. (Height). • SAFE AREA:- 1.2Mtr x 3Mtr • Seated puller equipment made up of "C" Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters • The center pipe is of 100NB made from "C" Class G.I. pipe. • Bottom support i s of M.S. round plate of 0 250 mm & 10mm thickness is welded. • All linkages are made up of 25NB "C" class G.I. pipe. • The handle frame is of 32NB "C" class G.I. pipe. • The seat frame is of 32NB "C" class G.I. pipe, • To build structure bushes are used which are made from seamless pipe of 60mm O.D. and 5mm thickness as well as 60mm diameter solid bar bush is used. • The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB "C" class. Welded with M.S. round plate of 0250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. • Foundation cover Closing Cap is made from FRP Material with 0.7 mm Thickness. • The seats and Back rests are fitted on the outer frames a r e made up of M.S. Sheet of size 330 mm X300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. • Closing Caps are made up of high quality Fiber reinforced Plastic material. • Pins used of Diameter 25mm and 17mm are made up from SAE 8620 bright material. • The bearings used are of " 6205zz" and "6203zz" permanent lubricated sealed bearing of reputed brand. • High tensile steel with galvanized nuts & bolts are used for assembly. • The cerclips used for assembly are of A16 • The powder coating done with Pure Polyester powders of Ackzonoble or Berger Paints with 60 to 70 micron thickness.

CHEST PRESS CUM SEATED PULLER • DIMENSIONS: - 2000mm (Length) x 710mm (Width) x 2200mm. (Height). • SAFE AREA: - 3.0 Mtr x 1.7Mtr. • Chest press cum seated puller equipment made up of "C" Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters • The center pipe is of 100NB made up of "C" Class G.I. pipe. • The bottom welded with support of M.S. round plate of 0250 mm & 10mm thickness. • The connecting pipes are made up from 25NB "C" class G.I. pipe. • The handle frame is made up from 32NB "C" class G.I. pipe. • To build structure bushes are used which are made from seamless pipe of 50mm O.D. and 6mm thickness as well as 50mm diameter solid bar is used. • The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB "C" class welded with M.S. round plate of 0250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. • The seats and Back rests are fitted on the outer frames are made up of M.S. Sheet of size 330 mm X300 mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. • Closing Caps are made up of high quality Fiber reinforced Plastic material. • Pins used of Diameter 25mm and 17mm are made up from SAE 8620 bright material. • The bearings used are of "6205zz" &"6203zz" permanent lubricated sealed bearing of reputed brand • High tensile steel with galvanized nuts & bolts are used for assembly. • The cerclips used for locking is made up of A24 & A16 • The powder coating done with Pure Polyester powders from Ackzonoble or Berger Paints with 60 to 70 micron thickness.

THI-CHI SPINNER (2 WHEEL) • DIMENSIONS: - 700mm (Length) x 1000mm (Width) x 1280mm (Height). • Safe Area:- 1.9Mtr X 1.9Mtr • Thai chi spinner Equipment made up of "C" Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters. • The center pipe is of 100NB made up of "C" Class G.I. pipe. • The handle movement round frame is made up from 25 NB "C" class G.I. pipe • The foundation used for fixing is a structure and made from center pipe of G.I. of 80 NB "C" class Welded with M.S. round plate of 0250 mm & 10mm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. • Closing Caps are made up of high quality Fiber reinforced Plastic material. • The pins used are made up of 0 25 mm of SAE8620 bright material. • The bearing used is "6201zz" &"6205zz" permanent lubricated sealed bearing of reputed brand. • High tensile S. S. nut bolts are used for assembly. • Foundation cover Closing Cap is made from FRP Material with 0.7 mm thickness. • The cerclips used for assembly is of A24 and All. • The nylon bush is used for handle knob. • The powder coating done with pure Polyester powders from Ac kzo n o b I e or Berger Paints with 60 to 70 micron thickness. • Bolt M8X16 mm and Nylock nut of M8 made of SS 304 used on nylon cap mounted on pins to protect bearings and pins from rain and dust.

SURFING BOARD • DIMENSIONS: - 1000mm (Length) x 600mm (Width) x 1400mm.(Height). • Safe Area:-1.5 x 1.3Mtr. • Surfing Board Equipment made from "C" Class G.I. pipe of different NB. NB stands for Nominal Bore Sizes i.e. Internal Diameter of pipe in millimeters • T h e main frame is of 80mm NB made from "C" class G.I. pipe. • The bottom support welded of M.S. plate of 0 250 mm & 10mm thickness. • The handle frame is of 25N B made from "C" class G.I. pipe. • The foundation used for fixing is a structure and made from center pipe of G.I. of 80NB "C" class welded with M.S. round plate of 0250 mm & 10rnm thick. Main pipe supported with 25 mm X 25mm M.S. angles of 3 mm thickness and 20mm x 40mm CRC square pipes of 3mm thickness. • Bushes are used 70mm Outer Diameter with 5mm thickness is used. • The footrests made from high quality fiber reinforced plastic. • Closing Caps are made up of high quality Fiber reinforced Plastic material. • T h e pins used are made up of 035 mm SAE 8620 bright material. • The bearing used are of "6007zz" permanent lubricated sealed bearing of reputed brand. • High tensile steel with galvanized nut bolts are used for assembly. • T h e cerclips used for assembly is of A34. • The powder coating is done with Pure Polyester powder of Ackzonoble or Berger with minimum 60 to 70 micron thickness

BACK EXTENSION DIMENSIONS: - 1400mm (Length) x 700mm (Width) x 820mm (Height). SAFE AREA: - 2.4Mtr x 1.7Mtr. Back Extension Equipment made from "c" G.I. Pipe of different NB pipe. (NB stands for Nominal Bore i.e. Internal Diameter of pipe in mm). The main frame is of 50mm NB made from "c" Class G.I. pipe. The Foot resting frame of 32mm NB made from "c" Class G.I. pipe. The handle frame is of 25NB made from "c" Class G.I. pipe. The seat fitted on the outer frames i s made up of M.S. Sheet of size 330mm X 300mmX2mm thickness and deep drawn and pressed in tools and dies to have uniform radius of 20 mm with no sharp edges. The foundation used for fixing is consists of 50mm NB made from "c" Class G.I. pipe. The footrests are made from casted Aluminum material, having sizes 130 x 310 x 5 mm thick. With the support of 250mm X 115mm X 3mm thick MS plate. The powder coating done with Pure Polyester powder o f Ackzonoble or Berger with 60 to 70 micron thickness.

Providing and fixing fine dressed sand "Stone Benches" for Visitors, approved sand stone/approved stone as per approved drawing and design with moulding work 100mm thick (Top & Legs) fixing with proper adhesive, legs fixed in concrete block 1:2:4 (45 cm x 45 cm x 30 cm) complete in all respect (Size 150 cm x 45 cm.)

Supplying & commissioning of ornamental pole with Single arm designer brocket of total pole height 8000mm nominal above the foundation top level with main shaft made of M.S. pipe of bottom 1500mm height 139.4mm dia B class & top 5500mm length 89 mm dia B class & base made of cast iron. The pole shall be fabricated with designer SG unbreakable iron base of grade 500h cast iron rings, M.S. Bracket with cast iron ring fixed on main shaft. The pole shall have window opening with weather proof flush door & lacking arrangement for housing at bottom the pole to accommodate electrical accessories. The pole shall be painted with polyure thane paint of opposed colour finish. Size of the C.C. foundation was not less than 450mmx450mmx1500mm and foundation bolt shall be made from M.S. steel 20mm dia 750mm long. 8 mtr make Bajaj/Surya/K.lite/Philips/Schreder/Keselec.

Supplying of 120W LED suspension type decorative street light fitting, made of spun aluminium housing, polycarbonate diffuser protector with IP 65 protection for optical compartment with high power LED'S & inbuilt driver with efficiency > 0.85 and having surge protection device, color temperature 5700 K.Bajaj Make: BORAGE 120W LED.

Fix Provision for O&M of Garden area (Horticulture works) created under this contract including but not limited to - All Civil, Electromechanical works - All Open Gym & Children Park Areas Equipment - Repairs and Painting works - Watering & trimming in parks - Weeding &hoeing - Thavala preparation/formation - Hedge/lawn cutting work - Seasonal flowering plants - Cleaning, watch & ward of park& electric operation etc. for Three Years as per Tender Document (yearwise payment amount is given in tender document) - 1 years defect liability period & 3 years O&M

Bidder Name

Amount

CHHAGANI RAM GEHLOT

SHRI BALAJI NURSARI

M/s. B.S.Solanki Builders

M/s. Mother Garden Care

M/s. B.S.Solanki Builders

SHRI BALAJI NURSARI

CHHAGANI RAM GEHLOT

CHHAGANI RAM GEHLOT

M/s. Mother Garden Care

M/s. B.S.Solanki Builders