AS AS OF BUILDING NO P-203 (SHILPIKA) INCLUDING WAITING AREA AT NAVAL PARK AND PROVN OF SPLIT AIR CONDITIONER IN BUILDING NO. P-150 AT NSB UNDER GE (NB) VISAKHAPATNAM

Amount

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, trenches for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan and n exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft/loose soil complete all as specified and directed.

Removing excavated materials exc 1.5 Km but n. exc 15 Km and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

M & L for Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, etc complete all as specified and directed.

M & L for use & waste Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundations and plinth beams and similar work, vertical or to batter complete all as specified and directed.

M & L for use & waste Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etcetc complete all as specified and directed.

M & L for use & waste Formwork to sides of pillars, posts, struts, piers, columns and stanchions for flat rough finished surfaces of concrete complete all as specified and directed.

M & L for Reinforced Cement Concrete M-30 (Design Mix) (using 20 mm graded stone aggregate) as in foundations including rafts, footings, beams and mass concrete, etc complete all as specified and directed. (Note" Reinforcement will be measured and paid seperately)

M & L for Reinforced Cement Concrete M-30 (Design Mix) (using 20 mm graded stone aggregate) as in columns, pillars, posts and struts complete all as specified and directed. (Note : Reinforcement will be measured & paid seperately)

M & L Reinforced Cement Concrete M-30 (Design Mix) (using 20 mm graded stone aggregate) as in beams, cantilevers, lintels over 1.5m span complete all as specified and directed. (Note : Reinforcement will be measured & paid seperately)

S & F high strength corrosion resistant TMT steel bars 10 mm dia., and over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

S & F high strength corrosion resistantMild steel TMT bars 5mm dia and over upto and including 10mm dia in strirrups, spacers and binders spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified and directed.

S & F Pre-Painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturer's instruction complete all as specified and directed.

S & F Pre-Painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges/vally gutter, fixed with self tapping screws as per manufacturer's instruction complete all as specified and directed.

S & F aluminium Anodised snap grid frame work of size 600mm x 600mm frame work for ceiling with aluminium T section of size 38mm x 25mm x 1.5mm thick for main runners, 25x25x1.5mm thick for cross runner and angle size 25x25x1.5mm thick alongwith wall suspended and including Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to ceiling members in proper position, fixed with aluminium staple on snap grid as per manufacturer's instructions including 6 mm thick non asbestor E-board, HSPC, designer fixed to frame complete all as specified and directed by the Engr-in-Charge.

S & F MS steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S. 1161-1979 grade St-240 complete all as speicfied and directed.

M & L for Mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete conforming to Fe-290 (Gde E-165) complete all as specified and directed.

S & F Rolled mild steel in Plates (plain or chequered) channels fo grade Fe 410-W (Gde-E- 250) quality-A, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as speicfied and directed.

S & F Mild steel screw bolts of 16 to 20 mm diameter of shank (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5cm and n exc 10cm long complete all as specified and directed.

M & L for Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zine chrome primer complete all as specified and directed.

M & L for Brick work with fly ash brick, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 using old size brick complete all as specified and directed.

M & L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished the surfaces even and fair without using extra cement complete all as specified and directed.

M & L for rendering 15 mm thick in two coats (10mm+5mm each) on fair faces of brick work or concrete surfaces in cement mortar 1:4, mixed with integral water proofing compound with weight of cement in top layer as per manufacturer's instructions and finished the surface even and fair without using extra cement complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item).

Supply only integral water proofing compound (ISI marked) complete all as specified and directed.

M & L for applying water proof cement based putty @ 1Kg (undiluted)/Sqm of average thickness 1mm over the plastered/old painted wall after scrapping to prepare the surfaces even and smooth and sanding the putty surfaces with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 240 Grit or above to make the surfaces free from dus etc by skilled labour as per the following steps complete all as specified and directed: (a) Step 1: Mix the putty powder by adding water as per the manufacturer's instructions and mix it with putty mixer of mixing capacity of min 2.5 Kg putty per minute. (b) Step 2: Apply the first coat of prepared mixer with the help of fully automatic airless spray machine of putty application having glow speed of max 6 ltrs per minute with a maximum pressure 3300 PSI (c) Step 3: Allow 6-8 hrs time to dry the putty surfaces

M & L for applying one coat of acrylic water based interior grade primer @ 0.8 ltr (undiluted)/ 10 Sqm diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine of paint application with flow speed of min 1 ltr per minute having a pressure of 3300 PSI and allow 6-8 hrs to dry the surfaces for painting of susequent coat complete all as specified and directed.

M & L for preparation of new surfaces of wall/ceiling and applying two coats of oil bound distemper by using fully automatic Airless spray tenchnology machine with max pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr, the spray machine should be from reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and acccessories for applying distemper in hard to reach areas and penetration of distemper on the surface complete all as specified and directed. (Note: Sanding of surfaces shall be done by mechanical sander with 1500-2700 rpm with internal dust extraction system for clean environment certified by the Paint manufacturer)

M & L for applying one coat of acrylic water based exterior grade primer @ 0.9 Ltr (undiluted)/10 Sqm diluted with water in 1:1 ratio to be applied with fully automatic airless spray machine of paint application with a flow speed of min 1 Ltr per minute having presure of 3300 PSI and allow 6-8 hrs to dry the surfaces for painting of subsequent coats complete all as specified and directed.

M & L for applying Two coats of of water based 100% Premium acrylic smooth exterior emulsion paint with silicon aditive and colour stay technology, excellent Dirt Pick up resistance with low VOC less than 50 gm/litre as per the LEEDS specifications and UV resistance as per IS 15489:2004, Alkali & fungal resistance of required shade (Company Depot Tinted) @ 1.79 Ltr (undiluted)/10 Sqm for two coats diluted with water as per manufacturer instructions with fully automatic airless spray machine of paint application with a flow speed of min 1 Ltr per minute having presure of 3300 PSI and allow 6-8 hrs to dry the surfaces in both the coats of paint complete all as specified and directed.

M & L for hardcore of gauge n.exc 63 mm of broken stone or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M & L for moorum/red bajri filling under floors or in foundations including spreading, levelling, watering and consolidation complete all as specified and directed.

M & L for 100 mm thick, plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in sub-base of flooring, etc complete all as specified and directed.

M & L for Vitrified, designed, light shade coloured (light shade), tiles, 7 to 8 mm thick, (square/rectangular) polished, area of each tiles not exc 0.36 sqm, in floors, etc and set & jointed in neat cement slurry and 3mm wide joints shall be maintained with spacers which is to be filled with epoxy grout using masking tape and the masking tape is to removed after filling the epoxy grout including 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed.

M & L for 75 mm thick, plain cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) as in plinth protection etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed.

S & F Powder coated aluminium sections (minimum 50 micron) of approved colour as in door, window, ventilator frames, partitions with one or more rebates and door, windows shutters sliding/openable type/ventilator shutter including provision of necessary jointing cleats, glazing clips, neoprene rubber packing, powder coated aluminium snap beading, screws inclding provision of suitable size of powder coated aluminium fittings such as locking arangements, handles, stainless steel fiction hinges and tower bolts etc including fixing only glass panels/particle board panels/wire gauge/aluminium grill etc complete all as specified and directed. (Note : (i) The size of aluminium sections shall be all as specified in relevant IS Code and MES Schedule Part-I (ii) Glass panels/ Partricle Board panels/ Wire gauge/ aluminium grill shall be measured paid seperately as supply only rates under respective items here-in-below).

Supply only Powder coated Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge complete all as specified and directed. (Note: Rate for fixing included with the quoted rate of respective shutter)

Supply only 5.5 mm thick, sheet glass, ordinary quality and glazing with beading for door/window etc in square exceeding 0.5 Sqm in each pane complete all as specified and directed. (Note: The cost of fixing and glazing beads included with the unti quoted rate of respective shutter)

Supply only Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. (Note: The cost of fixing included with the unti quoted rate of respective shutter)

S & F Solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers complete all as specified and as directed.

S & F in repair 20 mm dia, brass chromium plated, curtain rod with bracket complete all as specified and directed.

S & F in repairs Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and directed.

S & F Collapsible steel gates, top hung, consisting of channel pickets, ivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and disposal of debris and rubbish to outside MD land complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M & L for Virified designed, light shade coloured, Ceramic tiles, 7 to 8 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.0 sqm, in floors etc. and set & jointed in neat cement slurry and 3mm wide joints shall be maintained with spacers which is to be filled with epoxy grout using masking tape and the masking tape is to removed after filling the epoxy grout and including 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed.

M & L for Vitrified, designed, light shade coloured, tiles, 7 to 8 mm thick, (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.0 sqm as in vertical surfaces such as skirting,dado, etc and set & jointed in neat cement slurry and 3mm wide joints shall be maintained with spacers which is to be filled with epoxy grout using masking tape and the masking tape is to removed after filling the epoxy grout and including 10 mm thick bedding in cement mortar 1:4 and necessary cutting of tiles complete all as specified and directed.

M & L for granite stone slab (of any type) 18 to 20 mm thick (Table rubbed and polished), machine cut, colour Mexican Red/Ruby Red/Z black/Paerl black etc design/pattern as directed including inlays, borders, margins in two or more colours/shades as in floors, trades of steps, cill cooking platform etc set and bedded and jointed with grey cement slurry and jointed and pointed flush using polymer based cementitious tiling joint filler to match the shade of the Granite slabs complete all as specified and directed. (Note: Single stone slab shall be used for entire length/height of steps, jambs, pillars, window cills, cooking platform etc and joints sahll match with the flooring complete)

M & L for granite stone slab (of any type) 18 to 20 mm thick (Table rubbed and polished), machine cut, colour Mexican Red/Ruby Red/Z black/Paerl black etc design/pattern as directed including inlays, borders, margins in two or more colours/shades as in skirting/dado vertical surfaces etc, set and bedded and jointed with grey cement slurry and jointed and pointed flush using polymer based cementitious tiling joint filler to match the shade of the Granite slabs complete all as specified and directed. (Note: Single stone slab shall be used for entire length/height of steps, jambs, pillars, window cills, cooking platform etc and joints sahll match with the flooring complete)

Taking down chowkats or frames, exc 1.5 but n.exc. 4 Sqm in each with shutter (without taking off shutter from the frame) complete all as specified and directed.

S & F Well seasoned First class hard wood (Teak) plain, solid, straight chowkat and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

M & L for Plain cement concrete 1:3:6, type C-1, (using 20 mm graded stone aggregate) as in lintel upto 1.5m span, cills and other similar band, plinth course, parapet, railing upto 60cm height, coping, kneelers, bed plates, hold fast block etc including weathering slightly rounded or chamfered angles including necessary form work complete all as specified and directed.

S & F mild steel bands, straps, supports or stays of rain water, ventilating pipes including bolts, hooks (stay) for large gates, hook and pintel hinges, clamps, hold fasts, wall ties, flat iron fillets for securing wire mesh, wind tie, fan hook and similar work including necessary drilling bolting or riveting etc conforming to Fe – 290 Gde E – 165 complete all as specified and as directed.

S & F 30 mm thick, first class hardwood, factory made, Plain framed, panelled shutter (two panel) with lock rail and panel of first class hardwood with moulded beads provided round the panel, the size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S & F 100 mm long, Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type C-13 complete all as specified and directed.

S & F 150 mm long, Brass barrel tower bolts, extruded section with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and directed.

S & F 600 mm size, and minimum 25mm dia, designer Brass handles, cast type polished bright complete all as specified and directed.

S & F 300mm long, Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and directed.

S & F 100mm mortice latch brass body, 6 lever with two keys, polished bright; vertical type and fixed complete all as specified and directed.

S & F in repairs, Aluminium (Die cast) body door Closer hydraulically regulated, designation No 3, universal type, suitable for door shutter of 851 to 1000 mm in width and of weight between 61 to 80 Kg complete all as specified and directed.

M & L for preparation & cleaning of new or previously untreated surfaces of wood or wooden surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic varnished over liquid transperant filler complete all as specified and directed.

S & F Floor door stopper, 150 mm overall length of cover plate, brass body and tongue with hard drawn steel spring, fixed in floor complete all as specified and directed.

Demolition of brick work or stone / boulder masonry, built in cement mortar including all quoins, pillars etc stacking the serviceable bricks after removing mortar and cleaning for re-use and disposal of debris and rubbish outside MD land as directed by the Engr-in-Charge.

M & L for brick work with fly ash bricks, straight or curved on plan to any radius, built in cement mortar 1:4 as in half brick thick walls using old size brick complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water and removing rubbish to outside MD land complete all as specified and directed

M & L for Complete removal of existing treatment from walls etc by scrapping with mechanical wall sander (having mechanical vacuum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7/9 inch to make the surfaces free from dust, loose paints etc by skilled labour complete all as specified and directed.

M & L for preparing new surfaces of wall/ceiling and applying two coat of smooth interior acrylic Plastic emulsion paint with rich matt finish having VOC less than 50 Grms per ltr complying LEEDS criteria @ 1.5 ltr (undiluted for two coats)/ 10 Sqm diluted with water in 2:1 ratio as per manufacturer's instructions by using Airless spray technology machine with max working pressure of 3300 PSI and capable of operating single spray gun with a max material hose length of 30 mtr, the spray machine should be from reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and acccessories for applying paint in hard to reach areas and penetration of paint on the surface complete all as specified and directed. complete all as specified and directed. (Note: Sanding of surfaces shall be done by mechanical sander with 1500-2700 rpm with internal dust extraction system for clean environment certified by the Paint manufacturer)

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness including cover fillets/snap grid/frame work etc complete all as specified and directed.

S & F 10mm thick PVC insulation panels with EPS stuck to 1mm plain PVC sheet suitably placed in and including false ceiling grid made of GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to cerntre / intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre complete including Hangers 6 mm dia GI (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of GI flat 40 x 3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia, 40 mm long complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails etc complete all as specified and directed.

S & F 30 mm thick, second class hard wood clean sawn boards or planks, width n exc. 20 cm complete all as specified and directed.

S & F 18/19 mm thick, plywood, grade BWP, type BB, fixed with screws to timber frame work, etc complete all as specified and directed.

S & F 18/19 mm thick, HDMR (High Density Moisture Resistance) board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work as in shutter of cup-board shelf, etc complete all as specified and as directed.

S & F 150 mm size, Brass handles, cast type, polished bright complete all as specified and directed.

S & F 0.90 mm thick, Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed.

S & F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, 30mm width of flape when open complete all as specified and directed.

S & F 20 mm dia, brass chromium plated, Tubular Towel rail complete all as specified and directed.

S & F bracket for 20 mm dia, brass chromium plated, curtain rod complete all as specified and directed.

S & F Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed.

S & F Well seasoned 2nd class hard wood plain, solid, straight chowkat and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

S & F 50mm size, 2 lever, brass Locks, cupboard, grade I complete all as specified and directed.

S & F 12mm thick fully glazed, toughened clear glass, cutting to proper shape and size, drilling and aligning for propper fixing and fitted with necessary fixing arrangement and all other necessary fittings and fixtures and mounting the edges with dry set neoprine/EPDM gasket complete all as specified and directed.

S & F 9.5 mm thick, frosted sheet glass, ordinary quality and glazing with wooden beading/rubber beading in square n.exc 0.5 Sqm in each pane complete all as specified and as directed.

S & F 9.5 mm thick, frosted sheet glass, ordinary quality and glazing with wooden beading/rubber beading in square esceeding 0.5 Sqm in each pane complete all as specified and as directed.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed.

Taking down unserviceable main switches, DBs, bus bars chambers, VTPN etc any capacity including all fittings and fixtures such as MCBs, isolator, etc and removing from site complete all as specified and directed.

Taking down unserviceable sub-main wiring (any numbers of cable) with rigid PVC/steel conduits/PVC casing-caping including cutting chases for conduits and making good disturbed surfaces complete all as specified and directed.

M & L for Point wiring with two runs of single core 1.5 Sq.mm. (Nominal area) PVC insulated unsheathed multistranded copper conductor cable FRLS (ISI marked) drawn through and including non metallic PVC conduit 20 mm bore (Minimum) medium grade (ISI marked) concealed type including metal GI boxes of suitable module including modular white cover plate of suitable module for fixing modular type switches, sockets, regulators etc. including provision of multistranded 1.5 Sq.mm copper conductor cable FRLS [ISI marked] as earth wire connected to common earth dolly and earth in distribution board complete all as specified and as directed, for one light/exhaust fan/fan point/call bell controlled by one way switch. (Note.: (i) The rate quoted is deemed to include making good the disturbed sufaces and to match the adjoining surface. (ii) The quoted rate is deemed to include cutting chases for concealed wiring including making good the same as per the existing one)

All as per item No. 87 above but for One 3/5 pin socket outlet 6 amps on independent board complete ditto

All as per item No. 87 here in before but for one 15 Amps power point on the independent board with two runs of PVC insulated and unsheathed copper conductor cable of size 2.5 sqmm multistranded FRLS (ISI marked) and 2.5 sqmm PVC insulated unsheathed solid copper conductor cable FRLS (ISI marked) as earth lead complete ditto

All as per item No. 87 here in before but for one 15 Amps power point on the independent board with two runs of PVC insulated and unsheathed copper conductor cable of size 4 sqmm multistranded FRLS (ISI marked) and 4 sqmm PVC insulated unsheathed solid copper conductor cable FRLS (ISI marked) as earth lead complete ditto

S & F switch modular single pole one way 6 amp 240 volts,1 Module complete all as specified and as directed.

S & F Modular socket outlet 6A, 2/3 pin combined, 2 module, AC 230V, 50HZ complete all as specified and as directed.

S & F switch modular single pole one way 16 amp 240 volts,1 Module complete all as specified and as directed.

S & F Modular socket outlet 6A/16A, 2/3 pin combined, 2 module, AC 230V, 50HZ complete all as specified and as directed.

S & F stepped type modular fan regulator ,100/120 W 1/ 2 module complete all as specified and as directed.

S & F ceiling rose, 65 X 50mm two to three terminals, PVC/polycarbonate, insolated body complete all as specified and directed.

S & F sheet metal enclosure with socket plug top and MCBs having single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 20Amp 240V, B-curve complete all as specified and as directed.

M & L for Sub main wiring with 2 runs of Single core 10 sqmm [ for Phase & Neutral ] PVC insulated multi stranded FRLS (ISI marked) copper cable drawn through and including concealed PVC conduit of suitable size with all conduit accesories and fittings along with 1 run of single core 10 sqmm PVC insulated multi stranded FRLS (ISI marked) copper cable as earth continuity conductor complete all as specified and as directed. (Note :- (i) Two runs of 10 sqmm and one runs of 10 sqmm cable as earth wire and one run of conduit shall be measured as one length (ii) The quoted rate is deemed to include cutting chases for concealed wiring including making good the same as per the existing one)

S & F Distribution Board, SPN 12 Way, 240V, Double door with IP 43 protection, IK 09 complete all as specified and as directed. (Make: Havell's cat part No. DHDPSHODRW12 or equivalent make as per List of Manufacturer's)

Supply, fixing, commissioning and testing MCB SPN 6-32A Amps, 240 Volts, 10KA, C Curve complete all as specified and as directed Havell's cat part No. DHMGCSNF006-032 or equivalent make as per List of Manufacturer's)

Supply, fixing, commissioning and testing MCB SP 6 to 32 Amps, 240 Volts, 10KA, C Curve, complete all as specified and as directed (Make: Havell's cat part No. DHMGCSPF006-032 or equivalent make as per List of Manufacturer's)

S & F LED tube light fittings, retro bar professional WH 5700K to 6000K, 20 Watt and 2000 Lumens of cool white with all accessories, internally prewired and connecting up with twin core twisted copper conductor cable of suitable size including tube lamp complete all as specified and directed. (Make: Havell's Cat No. LUMILINEPLUSBS20WLED865SPCSS or equivelant of make as per list of manufacturer)

S & F LED multipurpose zoom light with high output diffuser, 15 Watt, 220 V, AC, decorative type with driver holder and LED lamp and connecting up with twin core twisted copper conductor cable of suitable size including lamp complete all as specified and directed. (Make: Jaquar Cat No. LZOM01R015XW or equivelant of make as per list of manufacturer)

S & F LED Instra Ray round slim, magnetic light fitting with with high output diffuser, 9 Watt, 220 V, AC, decorative type with driver holder and LED lamp and connecting up with twin core twisted copper conductor cable of suitable size including lamp complete all as specified and directed. (Make: Jaquar Cat No. LINRSL2R09XW or equivelant of make as per list of manufacturer)

S & F LED focus light fitting with high output diffuser, 20 Watt, 220V AC, decorative type with driver holder and LED lamp and connecting up with twin core twisted copper conductor cable of suitable size including lamp complete all as specified and directed. (Make: Jaquar Cat No. LFCL01R020XW or equivelant of make as per list of manufacturer)

S & F LED COB downlight, 15 Watt, 240V AC having 36 degree angle recessed type with high efficency PMMA difuser, soft glare free light complete with driver, holders, LED lamps suitable for roof ceiling with all accessories and connecting up with twin core twisted copper conductor cable of suitable size including lamp complete all as specified and directed. (Make: Jaquar Cat No. LETS36R015XW or equivelant of make as per list of manufacturer)

S & F Lamp Holder, PVC/ Polycarbonate type with backplate suitable for batten fitting complete all as specified and as directed.

S & F in repairs LED Bulb, 9 Watts, B-22 Lumen ≥ 900, Luminous afficacy ≥ 100 Lum/Watt, CCT:WW/NW/CW, CRI > 80 Ra, IP 20 rated, overmoulded plastic housing, polycarbonate diffuser, 4KV surge Protection with over voltage protection withstand upto 440 V (for 10 Minute) with open and short circuit protections as per IS: 16102 complete all as specified and directed.

S & F Rigid non-metalic PVC conduit (20mmdia) exclusive of boxes (junction/ treminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hook etc. complete all as specified and directed.

Supply, fix, installation and commissioning BLDC ceiling fan of less noise, silent operation, speed controlable by regulator, light colour, conforming to IS-374-2019, 1200 mm sweep, 230 Volts, BEE 5 Star rating, any Govt recognised Lab tested, power factor >0.94 Wattage and not more than 35 Watt, air delivery not less than 215cfm and all accessories such as down rod etc and connecting up with 1.5 Sqmm, PVC insulated, multistranded copper conductor cables from ceiling rose to fan and fixing in existing position including taking down existing unserviceable ceiling fan of any descriptions and deposited at MES store yeard complete all as specified and directed. (Note: Ceiling fan should have minimum 3 years manufacturer's warranty) (Make : USHA/Havell's/Bajaj/CG)

Supply, install, testing & Commissioning, 5 STAR rated Hi wall split type air conditioner with indoor and outdoor units complete with cordless remote control unit and with in-built advanced air filters for better indoor air quality with latest inverter technology, having eco friendly refrigerant gas, copper condenser coil, EER 4.5 or above of capacity 2.0 TR, summer cool, Inverter compressor, automatic 2D swing copper condenser, BLDC motor, necessary copper pipe connections including cutting, bending, brazing, insulation on pipes etc, PVC drain pipe, electric connection in between indoor and outdoor unit with suitable size of PVC insulated, multi-stranded copper cable complete with all fixing accessories such as bracket etc complete all as specified and directed. (Note: The unit rate quoted above shall deem to be inclusive of the following accessories/works:- (i) Powder coated MS fixing brackets of suitable size for outdoor and indoor units at any height (ii) Copper tube of suitable size upto 2m each (iii) Drain pipe made of High Density Polyethylene pipes [HDPE] of pressure rating 6Kg/Sqcm of 20mm dia upto 2m each (iv) 4 core, 4 Sqmm PVC insulated and PVC sheathed, heavy duty multi-stranded copper conductor cable, 1100 Volts, FRLS grade as required for connecting indoor and outdoor unit (v) Drilling hole on brick wall to facilitate routing of copper pipe, drain pipe and cable from indoor unit to outdoor unit (vi) Sealing hole from outside from outside with white cement and making good disterubed surfaces as per the existing one (vii) Pressure testing, cooling performance check and product demonstration (viii) M & L for fixing remote control in wall complete)

S & F voltage stabilizer for automatic operation,, single phase naturally air cooled indoor type and designed for input variation between 170 V to 250 V with output of 230V with accuracy of +/- 2.5% variation of capacity 5.0 KVA complete all as specified and directed.

S & F in repairs copper tubing of 1/4" dia suitable for suction/discharge line of Split Acs including insulation of tube complete all as specified and as directed.

S & F in repairs copper tubing of 1/2" dia suitable for suction/discharge line of Split Acs including insulation of tube complete all as specified and as directed.

Supply, laying, connection and testing, 25mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed

Supply, install, testing & Commissioning, 5 STAR rated Hi wall split type air conditioner with indoor and outdoor units complete with cordless remote control unit and with in-built advanced air filters for better indoor air quality with latest inverter technology, having eco friendly refrigerant gas, copper condenser coil, EER 4.5 or above of capacity 1.5 TR, summer cool, Inverter compressor, automatic 2D swing copper condenser, BLDC motor, necessary copper pipe connections including cutting, bending, brazing, insulation on pipes etc, PVC drain pipe, electric connection in between indoor and outdoor unit with suitable size of PVC insulated, multi-stranded copper cable complete with all fixing accessories such as bracket etc complete all as specified and directed. (Note: The unit rate quoted above shall deem to be inclusive of the following accessories/works:- (i) Powder coated MS fixing brackets of suitable size for outdoor and indoor units at any height (ii) Copper tube of suitable size upto 2m each (iii) Drain pipe made of High Density Polyethylene pipes [HDPE] of pressure rating 6Kg/Sqcm of 20mm dia upto 2m each (iv) 4 core, 4 Sqmm PVC insulated and PVC sheathed, heavy duty multi-stranded copper conductor cable, 1100 Volts, FRLS grade as required for connecting indoor and outdoor unit (v) Drilling hole on brick wall to facilitate routing of copper pipe, drain pipe and cable from indoor unit to outdoor unit (vi) Sealing hole from outside from outside with white cement and making good disterubed surfaces as per the existing one (vii) Pressure testing, cooling performance check and product demonstration (viii) M & L for fixing remote control in wall complete)

S & F copper tubing of 3/8" dia suitable for suction/discharge line of Split ACs including insulation of tube complete all as specified and as directed.

S & F copper tubing of 1/4" dia suitable for suction/discharge line of Split Acs including insulation of tube complete all as specified and as directed.

S & F Rigid non-metalic PVC conduit (25mmdia) exclusive of boxes (junction/ treminal) but inclusive of all tees, bends, elbows, reducers, bell mouth tube ends and fixing accessories such as couplers, lock nuts, saddles, pipe hook etc. complete all as specified and directed.

S S V R PROJECTS AND INFRASTRUCTURE

M B CONSTRUCTIONS

SRI VIJAYA LAKSHMI ENTERPRISES

SRI JAYANTH ASSOCIATES

RAVITEJA ENGINEERING WORKS

ASR CONSTRUCTIONS

SRI SRK ENGINEERS

M/S REAL POWER SYSTEMS

K K INFRA