CERTAIN REPAIRS TO KERB STONES , HARDSTANDING AND ROADS OF TECH AREA AT AF STN JODHPUR

Amount

Demolition of Kerb stone ,Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete block walling complete disposing of debris outside MD land complete all as specified and as directed .

Demolition of concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) and disposing of debris outside MD land complete all as specified and as directed.

M&L for 75mm thick PCC (1:4:8) type D-2 (using 40mm graded stone aggregate) as in sub base etc complete all as specified and directed.

M&L for providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

Scarifying mechanically by miller machine or picking gravelled , macadam or bituminous macadam surface in area not exc 400 Sqm , up to 150mm deep complete all as specified and directed.

Repair to pot holes not exc 1sqm each including sweeping free from dust and mud ,or water ,scoring sunken surface in roads ,path etc cutting around edges to at least 25mm in depth making good by applying tack coat with VG-10 gde paving bitumen at 5 kg per 10 sqm, putting in premix as specified for think bituminous carpet (2 cm thick) well rammed and sealed with premixed sand seal coat (6.8 kg of binder with 0.06 cumof sand), again well rammed (including suppy of premix binder and sand) depth of potholes n exc 30mm.

M&L for applying evenly a priming /tack coat with bitumin VG -10 grade conforming to IS: 73 at a rate of application of 0.3-0.4 kg/Sqm on bituminous surface as specified in Table 500-5 of MORTH Specification for road and bridge works 2013 ,using mechanical sprayers complete all as specified and as directed.

M&L Bituminous premix Semi dense Asphaltic concrete 30 mm average consolidated thickness with 5.5% binder content by weight of total mix with bitumen of grade VG-30 (conforming to IS-73-2006) laid/rolled and compacted to required gradient and camber with 8 to 10 toone complete all as specified and directed by Engr-in-Charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified.

M&L Applying two coat of synthetic enamel paint over a coat of primer on brick, stone, concrete, asbestos cement or plaster surface of any description over 10cm girth or width, not otherwise described including preparation of new surface.

M&L for preparation of old painted surface applying one coat of synthetic enamel paint on brick, stone, concrete, asbestos cement or plaster surface of any description over 10cm girth or width, not otherwise described complete all as specified and directed.

Painting lines, dashes, arrows, letters, etc., on roads, pavements and the like exc. 10 cm wide with Retro-Reflective Thermoplastic road marking paint, white or golden yellow, conforming to MoRT&H specification all as per manufacturer's specification and as directed.

MOHIT ENTERPRISES

Om Trading Corporation