SPL REPAIR TO BLDG NO HT 11 ALONGWITH CERTAIN PROVISION WORKS UNDER GE (SOUTH) AMBALA CANTT

Amount

Demolition of brick work built in CM incl all quions arches, pillar etc but excluding ashlar facing, dressed stone work and precast concrete articals, complete all as specified and directed by Engineer-in-Charge.

Material and labour for brick work with flyash bricks of class designation 75, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed by Engineer-in-Charge

Material & labour flyash Brickwork having class designation 75, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 etc complete all as specified and directed by Engineer-in-Charge .

Taking down Cement plaster on brick or stone walls including raking out joints hacking for key & scrubbing down with water etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for Rendering 15 mm thick on surface of brick work or concrete surfaces, finished even and fair (without using extra cement) on walls in cement mortar 1:6 ,complete all as specified and directed by Engineer-in-Charge.

Material and labour for Rendering 15mm thick on fair faces of brick work or concrete surfaces, finished even and fair (without using extra cement) on walls in cement mortar 1:4, using water proofing compound complete all as specified and directed by Engineer-in-Charge NOTE:WPC will be measured and paid for separately.

Material & labour for rough cast plastering over and incl 10 mm thick rendering in cement mortar 1:3 and while it is still in plastic state the rough cast mixture consisting of crushed stone or fine gravel aggregate (which is generally of size between 6 to 12 mm depending on the texture required) mixed with coarse sand and cement in the ratio of 1: 1: 1 shall be applied and finished even. The mix of cement and sand shall be made slightly wetter than normal for rendering to ensure that larger aggregates are thoroughly covered, complete all as specified and directed by Engineer-in-Charge. Rough cast plaster shall be applied as specified clause 14.22 of SSR Part-I .

Supply only integral water proofing compound, complete all as specified and directed by Engineer-in-Charge.

Material and labour for preparation of new plastered surface of walls & application of two coats of cement based paint over a coat of primer complete all as specified and directed by Engineer-in-Charge

Material and labour for preparation of old plastered surface of walls including removal of existing treatment & application of two coats of cement based paint over a coat of primer complete all as specified & as directed

Material and labour for preparation of new plastered surfaces of walls and three coats of white wash complete all as specified & as directed

Material and labour for preparation of old plastered surface of walls including removal of existing treatment & application of three coats of white wash complete all as specified & as directed

Dismantling of AC corrugated, semi corrugated sheet including ridges etc. in roof covering complete all as specified and directed by Engr-in-charge.

Dismantling of ceiling boards (fibre, pulp, insulation, etc.) or insulation boards /slabs/ blankets, any thickness, including cover fillets, false ceilings etc complete all as specified and directed by Engr-in-charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed by Engineer-in-charge.

Material and labour for Roof Trusses (framed) , trussed , purlins, crane gantries, rails and fastenings and heavy bracket framing ( Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete as all specified and directed by Engineer-in-Charge.

Supply and fixing steel work in tubular trusses, stanchions including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 Grade St-240 , complete all as specified and directed by Engineer-in-Charge.

Material and labour for plates (plain and chequered) channels, square cut or notched ( ordinary and counter sunk) forming holes without any attachment of Fe-410W(gde-E-250) quality A , complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc complete all as specified and as directed by Engr-in-charge.

Supply and fixing Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm of any colour having tensile strength of 550Mpa as in roof covering/cladding to wall fixed with self tapping screws etc complete all as specified and as directed by Engr-in-charge.

Supply and fixing false ceiling with semi perforated 12mm thick micro tegular edged GRG false ceiling tiles at all heights with glass fibre reinforced gypsum false ceiling tiles of size 595x595 mm of approved texture, design & patterns having moisture content less than 2%, humidity resistance of 99% , NRCO 0.50 to 0.75 as per IS 8225:1987, noncombustible as per BS 476 (part 4)- 1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T grid of hot dipped galvanised iron section of 0.33mm thick (galvanised @120 gms per sqm on both sides) comprising of main T runners of size 15x32mm of length 3000mm, cross T of size 15x32mm of length 1200mm & secondary intermediate cross T of size 15x32mm of length 600mm to form grid module of size 600x600mm , suspended from ceiling using galvanised mild steel item (galvanising @ 80 grms per sqm) ie 50mm long , 8mm outer dia M-6 dash fasterners, 6mm dia fully threaded hanger rod upto 1000mm length and L shape level adjuster of size 85x25x2mm . Galvanised iron perimeter wall angle of size 24x24x0.4mm of length 3000mm to be fixed on periphery wall /partition with the help of plastic rawl plugs at 450mm centre to centre & 40mm long dry wall wood screws . The work shall be carried out as per specification , drawings & direction of Engineer-in-Charge

Demolition of stone slabs and tiles of any description or thickness in floors aprons etc laid bedded and pointed in any mortar , complete all as specified and directed by Engineer-in-Charge.

Material and labour for machine cut pre polished kota stone slab flooring minimum size 55x55 cm 20-25mm thick over cement screed base 15mm thick in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed by Engineer-in-Charge.

Material and labour for pre polished kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over cement screed base 10 mm thick in CM 1:4 including rubbing and polishing complete all as specified and directed by Engr-in-charge.

Demolition of Cement Concrete as in ground floor & paving not exceeding 15cm thick (above or below ground level) , complete all as specified and directed by Engineer-in-Charge.

Material and labour for 50 mm thick plain cement concrete 1:3:6 type C1 (using 20 mm graded crushed stone aggregate) as in plinth protection finished fair and even smooth without using extra cement complete all as specified and directed by Engineer-in-charge. Note :- The plinth protection shall be laid in panels and lenth of each panel shall not be more than 2.00 m including 6mm joints filled with 85/25 grade bituman and sand in the ratio (1:3) shall be provided, complete all as specified and directed by Engineer-in-Charge

Material and labour for 18 to 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in 15mm thick cement mortar (1:4) and jointed with grey cement slurry @ 3 Kg/Sqm, and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including grinding, polishing, rounding and moulding of stone slabs on edges, , complete all as specified and directed by Engineer-in-Charge.

Taking down chowkaths or frames not exceeding 1.5 sqm (without taking off shutter from the frame) each and removing from the site including dismantling brick work for hold fasts, complete all as specified and directed by Engineer-in-Charge.

Taking down chowkaths or frames exc 1.5 sqm but not exceeding 4.0 Sqm (without taking off shutter from the frame) each and removing from the site including dismantling brick work for hold fasts etc complete all as specified and directed by Engr-in-charge.

Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 100 x 65 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete all as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensionson plus side shall be acceptable but no extra payment on this account shall be made.

Supply and fixing of stainless steel butt hinges 100 mm long medium weight , complete all as specified and directed by Engineer-in-Charge..

Supply and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed by Engineer-in-Charge. Note : (i) stainless steel butt hinges and necessary S.S screws shall be paid separately)

Supply and fixing 150 mm long Aluminium anodised barrel tower bolts of extruded section and fixed , complete all as specified and directed by Engineer-in-Charge.

Supply and fixing aluminium anodised extruded fabricated type handle 150 mm long , complete all as specified and directed by Engineer-in-Charge..

Supply and fixing Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) 300 mm long and fixing with bolts extruded sections , complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of windows made of pre-painted steel (Base steel as per IS 513 of 0.58mm thick “D” Quality galvanized as per IS 277 with zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x48mm, section for fixed glass beading should be of 12x12mm and section for shutter should be of 48 x 25mm. Outer frame & mullion sections to have rebate for glazed shutters, fly mesh and 20 mm provision for guard bars/ grills fly mesh shutter section should be of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap. Elixir or equivalent stay, handles 2 Nos of heavy duty stain less steel pivot hinges shall be provided per shutter. The windows should be paneled with 4 mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade). Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of self expanding screws. Including 10mm square guard bars with 6” (152.4mm) pitch, complete for finished item of work including of all taxes, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing ventilators made of pre-painted steel (Base steel as per IS 513 of 0.58mm thick “D” Quality galvanized as per IS 277 with zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x50mm, section for fixed glass beading should be of 12x12mm and section for shutter should be of 48 x 25mm. Outer frame & mullion sections to have rebate for glazed shutters, fly mesh and 20 mm provision for guard bars/ grills fly mesh shutter section should be of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap. Elixir or equivalent stay, handles 2nos of heavy duty stain less steel pivot hinges shall be provided per shutter. The windows should be paneled with 4 mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade). Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of self expanding screws. Including 10mm square guard bars with 6” (152.4mm) pitch, complete for finished with suitable provision as in ventilator in toilet/bathroom/staircase , complete all as specified and directed by Engineer-in-Charge.

Material and labour for plain cement concrete 1:4: 8 type-D2 (using 40mm graded stone aggregaets) as in sub base to floor 100mm thick , complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Machine pressed precast conctete interlocking paver block of any shape and size conforming to IS 15658-2006 of 80 mm thickness M-40 Grade, complete all as specified and directed by Engineer-in-Charge.

Material and labour for sand filling under floors or in foundation including watering and consolidation 25mm thick complete all as specified and directed by Engineer-in-Charge.

Material and labour for precast cement concrete Type B1 1:2:4 (using 20mm graded stone aggregate) kerb stones with solid blocks exc 10cm in width and setting in cement mortar 1:4 complete all as specified and directed by Engineer-in-Charge.

Material and labour for plain cement concrete type B0 1:2:4 (using 12.5mm graded stone aggregate) as in lintels upto 1.5m clear span, cills, steps, seismic & other similar bands, coping, kneelers, apex stones , bed plates , water troughs & like including weathering slightly rounded or chamfered angles and throating complete all as specified and directed by Engineer-in-Charge.

Material and labour for painting to steel surfaces of any description not other wise described over 10cm width or girth with two coats of synthetic enamel paint over one coat of red oxide primer including preparation of new surfaces complete all as specified and directed by Engr-in-charge

Surface excavation not exc 30 centimetre deep and averaging 15 centimetre deep and getting out in soft/loose soil , complete all as specified and directed by Engineer-in-Charge.

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in soft/ loose soil, complete all as specified and directed by Engineer-in-Charge.

Material and labour for Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded stone aggregate) as in foundations, filling and mass concrete, complete all as specified and directed by Engineer-in-Charge.

Material and labour for 75 mm thick plain cement concrete type D 2, 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring, complete all as specified and directed by Engineer-in-Charge.

Material and labour for 25mm thick plain cement concrete type B0 1:2:4 (using 12.5 mm graded stone aggregate) as in subbase flooring complete all as specified and directed by Engineer-in-Charge.

Material and labour Glazed ceramic coloured tiles in vertical surface 300x450mm x 7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match as in skirting/Dado over 10mm thick rendering in CM 1:4, complete all as specified and directed by Engineer-in-Charge.

Material and labour for coloured Non Skid ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed in CM 1:6, complete all as specified and directed by Engineer-in-Charge.

Material and labour for 5mm thick cement rendering in CM 1:3 on fair faces concrete surfaces in ceiling finish the surface even and smooth after hacking the concrete surface complete all as specified and directed by Engineer-in-Charge.

Material and labour for 10 mm thick cement rendering in CM 1:6 on fair faces of brick work or concrete surfaces including provision of groove in plaster at junction of brickwork & concrete surfaces complete all as specified and directed by Engineer-in-Charge.

Material and labour for 15 mm thick cement rendering in CM 1:4 on other than fair faces of brick work or concrete surfaces finish the surface even and smooth including provision of 300mm wide chicken wire mesh on junction of concrete & brick work complete all as specified and directed by Engineer-in-Charge.

Material and labour for Reinforced cement concrete M-25 (Design Mix) (using 20mm graded aggregate) in foundations including rafts, footings,, foundation beams, plinth beams, bases for columns, etc, basement slabs, under reamed piles , complete all as specified and directed by Engineer-in-Charge.

Material and labour for Reinforced cement concrete M-25 (Design Mix) (using 20mm graded aggregate) in columns, pillars, piers, posts & struts complete all as specified and directed by Engineer-in-Charge.

Material and labour for Reinforced cement concrete M-25 (Design Mix) (using 20mm graded aggregate) in beams, cantilevers, bressumers, lintels etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for Reinforced cement concrete M-25 (Design Mix) (using 20mm graded aggregate) as in slab supported on walls, basement walls, ballast walls, & the like, any thickness, above top of footings, including attached pillasters & buttresses complete all as specified and directed by Engineer-in-Charge.

Material and labour for Reinforced cement concrete M-25 (Design Mix) (using 20mm graded aggregate) as in chajjas complete all as specified and directed by Engineer-in-Charge.

Material and labour for Reinforcement TMT bar 10mm dia and over cut to length, bend to shape required, incl cranking, bending, for hooping for columns, hooking ends and binding with and incl MS wire (Annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

All as per items No 59 here in before but 5mm dia and over upto and including 10mm dia in stirrups , spacers & binders, complete all as specified and directed by Engineer-in-Charge.

Formwork to sides of concrete foundations, footings, bases of columns, raft & raft beams, sides & soffit of foundation & plinth beams & similar work rough finished complete all as specified and directed by Engineer-in-Charge.

Formwork to sides & soffit of floor & roof beams, beam haunchings, girders, bressumers, lintels,cantilevers, shelves including, supports overhang etc fair finished, complete all as specified and directed by Engineer-in-Charge.

Formwork to sides of pillars, posts, struts, piers, columns, stanchions complete fair finished, all as specified and directed by Engineer-in-Charge.

Formwork to soffits of suspended slabs such as roof slab, floor slab, landing, and similar work not exc 300 mm thick horizontal or sloping complete fair finished all as specified and directed by Engineer-in-Charge.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railing, opening in walls, floor and roofs n exc 20cm and sides of RCC/pcc bands in walls, horizontal or sloping and similar work exceeding 10cm but not exc 20cm wide, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Vitreous China Half stall urinal complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, flush pipe, CP waste fitting, grating and Union for discharge pipe, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of vitreous counter top china wash hand basin of size 480x380x160mm fixed on to granite surface with all fittings and acessories required including chromium plated waste coupling including 32mm dia PVC waste pipe etc complete all as specified and directed by Engineer-in-Charge.

Supply and fixing vitreous china squatting pan, 'Orissa' pattern , size 580x440mm white, with integral footrest (excluding cistern & flush pipe ) fixed with concrete complete all as specified and directed by Engineer-in-Charge.

Supply and fixing PVC valveless, syphonic action type flushing cisterns 10 ltrs capacity , low level , white, with inlet ball valves , float and handle including brackets and pvc flush pipe 32 mm bore low level , fixed in repairs complete all as specified and directed by Engineer-in-Charge.

Supply and laying of CPVC pipes 16mm OD SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed by Engineer-in-Charge.

Supply and fixing water storage tank of 1000 ltr capacity, HDPE double layer, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut, screwed and suitable for iron pipe 20 mm bore , complete all as specified and directed by Engineer-in-Charge. Note:- Make of tank shall be engraved on the tank.

Supply and fixing PVC Connections 15 mm size with PTMP nuts of length 450mm, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 110 mm bore PVC (SWR) Soil, waste single socketed in any length with rubber ring joints laid in floors or trenches, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 75 mm bore PVC (SWR) Soil, waste single socketed in any length with rubber ring joints laid in floors or trenches, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 75 mm bore PVC (SWR) Soil, waste single socketed in any length with rubber ring joints fixed to walls, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 110 mm bore PVC (SWR) bends of any radius., complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 75 mm bore PVC (SWR) bends of any radius, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 110 mm bore dia PVC (SWR) reducers, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing PVC (SWR) vent cowl 75 mm bore, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing PVC (SWR) floor trap 75mm dia plain with PVC grating including jointing with solvent cement complete all as specified and directed by Engineer-in-Charge.

Material and labour for salt glazed stoneware gully trap, square or round moulded type 'P', 100x100mm size, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Fancy type chromium plated 15 mm bore angle valves, cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 15 mm bore Fancy type Chromium plated bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of ventilators made of pre-painted steel (Base steel as per IS 513 of 0.58mm thick “D” Quality galvanized as per IS 277 with zinc of 120 GSM). Primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with 5-7 microns thick alkyd backer. Section for outer frame should be of 72x55mm, centre mullion should be of 72x50mm, section for fixed glass beading should be of 12x12mm and section for shutter should be of 48 x 25mm. Outer frame & mullion sections to have rebate for glazed shutters, fly mesh and 20 mm provision for guard bars/ grills fly mesh shutter section should be of 20x40mm. The sections are to be cut to length mitre joined with corner bracket. Centre mullions to be fixed with mullion cap. Elixir or equivalent stay, handles 2nos of heavy duty stain less steel pivot hinges shall be provided per shutter. The windows should be paneled with 4 mm thick plain float glass and S.S. Mesh for fly mesh shutter (304 grade). Rubber Gaskets are provided all around the glass. The above frames should be fixed to the concrete/masonry wall by means of self expanding screws. Including 10mm square guard bars with 6” (152.4mm) pitch, complete for finished with suitable provision as in ventilator in toilet/bathroom/staircase, complete all as specified and directed by Engineer-in-Charge.

Cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends of edges of landings, steps, cills etc., and cutting chases for concealed water tubing and making good complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 15 mm bore pillar tap, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe, complete all as specified and directed by Engineer-in-Charge.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soft/loose soil ,complete all as specified and directed by Engineer-in-Charge.

Removing Excavated soils not exceeding 50m & depositing where directed at a level not exc 1.5 meter above the startiing point , complete all as specified and directed by Engineer-in-Charge.

Material and labour for providing 3 mm thick APP (Atactic polypropylene polymer) modified prefabricated five layer, weight not less than 3.6 Kg/Sqm water proofing membrane, black finished, reinforced with Non-woven polyster matt make as approved over roof consisting of a coat of bitumen primer @ 0.40 Ltr/Sqm by same membrane manufacturer of density 0.87 to 0.89 Kg/Ltr at 25º C temperature and viscocity 70-160 Cps. over the primer coat, the layer membrane shall be using butane torch and sealing all joints etc. after preparing the surface complete applying two coats of bituminous based Aluminium paint @ 0.2kg/sqm complete over and including 10mm thick cement plaster in CM (1:4) on RCC roof slab including cleaning of existing using WPC @ 2% by wt of cement complete as per standard practice as per manufactuter's instructions complete all as specified and directed by Engineer-in-Charge. The vital physical and chemical parameters of the membrane shall be as under:- (i) Joint strength in longitudinal and transverse direction at 25º C as 650/450 N/5 Cms. (ii) Tear strength in longitudinal and transverse direction as 300/250N/5 Cms. Softening point of membrane not less than 150º C cold flexiblility up to 20º when tested in accordance with ASTM (D-5147) (iii) The laying of membrane shall be carried out through the manufacturer or their authorized applicator only.

Supply and fixing of towel rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden / plastic cleats (minimum wt 190 gms )complete all as specified and directed by Engineer-in-Charge.

Material and labour for treating top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface , complete all as specified and directed by Engineer-in-Charge.

Material and labour for treating the backfill in contact with foundation at the rate of 7.5 lit of emulsion per sqm of vertical surface ( area of substructure in contact with backfill to be measured) complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper with hand roller , over a coat of alkaline resistant primer complete all as specified and directed by Engineer-in-Charge.

Material & labour for preparation of new plastered surfaces of ceiling and applying two coats of oil bound distemper with hand roller , over a coat of alkaline resistant primer complete all as specified and directed by Engineer-in-Charge.

Material and labour for preparation of new plastered surfaces of wall & applying two coats of acrylic emulsion paint over a coat of alkali resistant primer on walls complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of three shutter sliding windows made of prepainted steel and galvanised steel (base steel as per IS 513, D quality, galvanised as per IS 277 with zinc of 120 gsm, using factory made section powder coated with pure polyester powder upto 50-60 microns thick with total coated thickness of 0.58mm for outer frame and 0.58 mm thickness for sliding shutter section, the outer frame for three tracks size of 107mm x 44mm and the windows shutter section of 58mm x 36mm and the outer frame with two integrated guide tracks of 12mm width and 24mm deep for provision to slide the shutter /sash frame and also have a groove of 21mmx5mm to provide additional track and facilities with a water drain outlet component made of PVC and the shutter frame fitted with 5mm thick plain float glass, flyproof zali of reputed make and fixed with EPDM weathering seal resistant accessories and handle made of aluminium 1 No per each shutter and cut to length mitre jointed with corner brackets including installtion of windows system at site using anchor fasterners, inclusive of conveyance of all materials acccessories, labour charges erection site with complete finished item of work, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade, complete all as specified and directed by Engineer-in-Charge.

Excavation over areas not exc. 1.5 m deep & getting out Hard/ Dense soil , complete all as specified and directed by Engineer-in-Charge.

Excavation over areas for additional 1.5m or part thereof in depth beyond 1.50m , complete all as specified and directed by Engineer-in-Charge.

Material and labour for brickwork with sub class 'B' bricks, straight or curved on plan exc 6m mean radius , built in 1:6 cement mortar , complete all as specified and directed by Engineer-in-Charge.

Material and labour for rendering 15mm thick on external walls with 1:4 cement mortar finished even and smooth without using extra cement, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing CI pipe 100 mm complete all as specified and directed by Engineer-in-Charge.

Material and labour for MS TMT Bars 6 to 8mm dia and over cut to length, bend to shape required, incl cranking, bending, for hooping for columns, hooking ends and binding with and incl MS wire (Annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

Extra over for forming fair finished to drains or channels n exc 30 cm inner girth in cement concrete using extra cement including forms moulds, mitered/ stopped ends complete all as specified and directed by Engineer-in-Charge.

Material and labour for precast reinforcement cement concrete nominal mix 1:2:4 Type B-1 (using 20mm graded crushed stone aggregate ) as in manhole covers, including necessary formwork etc, set and jointed in CM 1:4 etc complete all as specified and directed by Engineer-in-Charge. Note : reinforcement shall be measured and paid separately under respective item

Material and labour for reinforced concrete pipes, 150mm bore , class NP3 , laid & jointed complete with collars laid in trenches at any depth including jointing & testing complete all as specified and directed by Engineer-in-Charge.

Material and labour for concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid & tested in cement concrete 1:3:6 type C-2 & having 150mm bore, complete all as specified and directed by Engineer-in-Charge.

Supply & filling of broken brick bats in soakage well of 2nd class bricks complete all as specified and directed by Engineer-in-Charge.

[E&M PORTION] Taking down carefully aluminium/ copper point wiring (light, fan,socket or power) complete, including fixtures and fittings such as switches, ceiling roses, pendants, regulators , sockets, light fittings etc., removing materials to stores for keeping in safe custody for taking credit and making good the disturbed surfaces of walls,ceilings etc, complete all as specified and directed by Engineer-in-Charge.

Material and labour for Point wiring with 1.50 Sqmm single core PVC insulated , unsheathed cable FRLSH, 1100 volt grade with multi stranded copper conductor drawn through and including PVC conduit not less than 20mm dia with and including accessories, concealed on wall/ and surface on ceiling and its fittings including all tees, bell mouth pieces and fixing accessories such as couplers, saddlers, pipe hooks etc, PVC junction boxes ISI marked with GI metal flush boxes made out of 1.2mm thick of any module from 2 to 18 module confirming to IS-5139(pt-I) of 1969 and IS:14772-2000 including modular cover plates with frame i.e. inner and outer plate extended upto 25 mm over metal flush boxes for housing the modular switches, socket outlets, fan regulators etc with brass screws and brass washers and making good the disturbed surfaces as per existing for one light / fan / Bell point contorlled by one switch including 1.5 sqmm single core PVC insulated and unsheathed FRLSH (FIRE Retardant Low Smoke and low Halogen) copper cable, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor upto common earth and connecting to common earth dolly with suitable size of lugs for one light point/ fan point/bell point controlled by one switch complete all as specified and directed by Engineer-in-Charge. NOTES:- 1. Switch, socket and fan regulators to be measured and paid for separately. 2. All chases will be cut by chase cutter only.

Description all as per item No 113.00 here in before but for socket out let point 6 Amps on same board, complete all as specified and directed by Engineer-in-Charge.

Description all as per item No 113.00 here in before but for socket out let point 6 Amps on independent board, complete all as specified and directed by Engineer-in-Charge.

All as per srl item No 113.00 above but point wiring for one socket out let 16 & 6 Amps (independent) controlled by one switch with using 2.5 Sq mm (nominal area) stranded copper conductor

Supply and fixing ceiling rose surface bakelite 65x50mm, 3 terminal complete all as specified.

Supply and fixing modular switches, one way, 6 amps one module, 230V, 50 Hz supply, , complete all as specified and directed by Engineer-in-Charge.

Supply and fixing modular switches, one way, 16/20 Amps, one module, 230 volt , AC supply, , complete all as specified and directed by Engineer-in-Charge.

Supply and fix modular socket outlet 6 amps, 2/3 pin combined 2 module, 230 volt, , complete all as specified and directed by Engineer-in-Charge.

Supply and fix modular socket outlet 6/20 amps,3 pin, 2 module, , complete all as specified and directed by Engineer-in-Charge.

Supply and fix modular fan regulator step type one module / 2 module, 100w 230 Volts, 50 Hz, AC , complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of LED luminaries of capacity 20 watt integrated aluminium batten with including Oppel diffuser complete including disconnecting and taking down old existing light fitting of any description and in any position complete all as specified and as directed.

Supply and fixing Bulk Head Fitting 10 Watt and connected with copper conductor cable of size 1.50 Sqmm, for fixing the light fitting , complete all as specified and directed by Engineer-in-Charge..

Supply and fix in repair recess/ surface mounted LED flat panel 2' x 2' with high efficient LEDs and glare free full decorative light fitting, 36 watt, energy efficient provided with including LED 36 watt with provision of 2/3 core PVC copper conductor cable 1.5 Sqmm size to light fitting , complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair of bracket for security light made up of 40/50mm dia suitable for security light, 0.6 metre long GI pipe, light grade, 120 degree bent to required length, fixed to wall with two clamps made of 20 x 3 mm mild steel flat minimum 15cm long, 4 nos 8mm dia bolts with nuts , complete all as specified and directed by Engineer-in-Charge.

Supply and fixing LED security light luminaire 30/35 watt , pressure die cast aluminum housing, toughened heat resistant glass, IP65 protection, better optics for uniform distribution with multiplte LEDs not less than 2 W each and having optical grade polycarbonate lens with all accessories internally pre wired and including connecting up with Two core 1.5 sq mm copper conductor cable from connector to ceiling rose to connection of light , complete all as specified and directed by Engineer-in-Charge.

Supply and fixing sheet metal enclosures vertical distribution board VTPN,(MCCB DB) 4 ways, double door , 415 volts with 200 amps rated bus bar IP 54 protection, with shrouded neutral bar and insulated bus bar and earth link, with and including MCCB 4 pole adjustable thermal release type ,100 AMPS ,16 KA as incomer and MCB s as out going complete with making suitable size of MS cabinet 1.2 mm thick dully grouted on the wall (flush) with opening arrangement including making connections with suitable size of lugs and making good the disturbed surface matching with existing surface , complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair SPN distibution board 8 way, double door, IP 43, as per IS 8623 including 200 amps fully insulated copper bus bar, insulated neutral bar, earth bar, door earthing, reversible doors, PAN assembly for easy installation and also incoming and outgoing connections with suitable size of lugs/thimbles , complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 Amp, in the MCB DB complete with connection testing and commissioning.

Supply and fixing 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of SPN and current carrying capacity 40 to 63 Amp, in the MCB DB complete with connection testing and commissioning.

Supply and fixing 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of SP and current carrying capacity 40 to 63 Amp, in the MCB DB complete with connection testing and commissioning.

Material and labour for sub main wiring with two single core FRLSH, PVC insulated unsheathed copper conductor cable 6.0 sq mm drawn in and including rigid non metallic PVC medium grade 25 mm dia concealed conduit with accessories on wall or ceiling with one additional PVC insulated , stranded copper conductor FRLSH of 6.0 sqmm,green colour for earth continuity conductor including including taking down old unserviceable sub main wiring and making good the disturbed surface complete, all as specified and directed.

Taking down unserviceable ceiling fan any size or any type and deposited to concerned AGE E/M store yard , complete all as specified and directed by Engineer-in-Charge.

Hanging only ceiling fan (M.D supply) in any model/size etc and making all connection using three core copper conductor flexible cable in size 0.75 sqmm including drawn through PVC flexible conduit pipe from ceiling rose to fan connector complete all as specified and directed.

Taking out old unserviceable earthing and material & labour for earthing with Galvanised Steel earth plate electrode 60cm x 60cm x 6.0 mm thick buried directly in ground vertically at a depth not less than 2.25metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, earth plate surrounded from all sides by 15cm thick packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by using Galvanised Iron wire of size 4.0 mm as earthing lead (upto terminal point) by means of bolts, nuts, check nuts and washers made of galvanised iron and thimbles and protected by light grade 40 mm dia GI pipe connected to main switch board or main control board and GI pipe medium grade 20mm bore for watering and including funnel , wire mesh , RCC pit cover and PCC chamber pit with PCC (1:3:6) type C-2 using 40mm graded stone aggregate, including excavation and earth work in any type of soil , returning , filling in approved soil and disposal of surplus soil to a distance not exceeding 50m all as specified and shown in electrical plate No 3 of SSR 1991(Part-I) complete all as specified and as directed by Engineer-in-charge. Note : The rates for earth work, GI protection pipe, funnel, wire wesh, CI cover, etc shall be deemed to be including in quoted rates.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, heavy duty electric cable 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 4 core as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, heavy duty electric cable 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 2 core as specified and directed.

Supply and fixing for GI protection pipe of 40 mm dia light grade for cable protection including all fittings laid in trenches or fixed on pole, complete all as specified and as directed.

Material and labour for unwashed dry sand cushioning for cable protection ,filling in trenches/ducts, complete all as specified and as directed.

Material and labour for old size bricks sub class 'B' for cable protection laid along length of cable complete all as specified and as directed.

Supply and fixing lamp holder, PVC/polycarbonate type with back plate suitable for batten fittings,, complete all as specified and directed by Engineer-in-Charge.

Supply and fix LED lamp 9 watt for batten fittings, , complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of LED luminaries of capacity 20 watt integrated aluminium batten with including Oppel diffuser complete all as specified and as directed.

Supply and fix surface mounted LED tube light fitting with high efficient diffuser mirror light, aluminium housing in CRCA body suitable and including 10 watt LED tube high efficient, AC 220-240 volts, 50 Hz and connecting with copper conductor flexible cable of size 0.50 Sqmm from ceiling rose to connector of the light including , complete all as specified and directed by Engineer-in-Charge.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) incl fixing acessories & connecting flexible copper wire from ceiling rose to fan complete all as specified and as directed.

Supply and fixing Exaust fan steel body AC single phase 230 Volts of size 300 mm Sweep , 1400RPM , double ball bearing, heavy duty with blades, frames and louvers including fixing arrangment complete as specified and directed.

Supply, installation and testing of storage type heater (Geyser) of 25 Litres Capacity, vertical type to sustain high pressure upto 8 bars with fixing bolts / fastener, necessary PCC/cement work and making good the disturbed surfaces to match with existing surface giving electric and water connection and testing after installation to entire satisfaction of the Engineer-in-Charge complete with following specifications : - (a) 5 Star rated (Vertical type) Necessary BEE cerificate from OEM shall be produced by the contractor at the time of sample approval. (b) Metal Body. (c) Glass line coated tank (Ferro-glass technology) / Polymer coated. (d) Incoloy glass coated heating element. (e) Adjustable thermostat. (f) Temperature indicator dial/digital type. (g) Multiple Heating Option. (h) Multiple Functional Safety Valve. (j) Thermal Cutout Capillary Type. NOTE : - Warranty certificate to be produced by the contractor from OEM for the following components before processing the bill. (a) For product - 02 Years (b) For metal tank 07 years.

Supply and fixing for 15mm dia galvanised iron tubing medium grade with and including all fittings such as bends, elbows, tees, short pieces, union etc passing through walls for water connection to geyser including, making good the disturbed surface complete all as specified and as directed.

Supply and fixing for 20mm dia galvanised iron tubing medium grade with and including all fittings such as bends, elbows, tees, short pieces, union etc passing through walls for water connection to geyser including, making good the disturbed surface complete all as specified and as directed.

Supply and fix Bib Tap cast copper alloy of 15 mm bore with crutch or butter fly handle ,screwed down ,screwed for pipe connection complete all as specified

Supply and fix stop/Gate valve cast copper alloy of 15 mm bore screwed down ,high pressure with crutch or butter fly handle screwded both end for pipe or for unions and fixed complete all as specified

Point wiring using approved colour coding as per IS with stranded copper conductor 4 Sqmm (nominal area ),single core ,FRLSH PVC insulated and unshaethed stranded cable 1100 volts grade ISI-694 marked in and including heavy duty ,PVC concealed conduit ISI marked for one industrial type metal clad earth plug and socket out let with earth dolly including FRLS PVC Insulated unsheathed copper conductor 4 Sqmm nominal cross section area as earth continuity conductor upto common earth and connecting to common earth dolly complete and including cutting/chasing of wall complete all as specified and directed by Engg in Charge.

Supply and fix single pole and neutral sheet metal enclosure with two pin & earth plug and socket comptete with one single pole MCB 20 Amps , complete all as specified and directed by Engineer-in-Charge.

Material and labour for Cutting and Screwing existing steel tubing in position without taking down for alterations or additions or lengthening screw on pipe to connector for 20mm Bore complete all as directed and specified.

Material and labour for Boring holes through glazed tile lining for pipes, etc n exc 50mm dia and making good disturbed surface including necessary PCC work complete all as directed and specified.

Supply and lay galvanised pipe medium grade, 25 mm bore, complete including all fittings, laid in trenches.

Suply and fix gun metal, globe or gate valves with iron wheel head screwed both ends for GI pipe and fixed all as specified for size 25 mm bore.

Material and labour for cutting/tapping existing CI/GI pipe of any bore in position for insertion of new TEE on any bore of pipe , complete all as specified and directed by Engineer-in-Charge.

Supply and fixing for GI protection pipe of 50mm dia light grade for cable protection including all fittings laid in trenches or fixed on pole, complete all as specified and as directed.

Material and labour for point wiring in existing conduit using approved colour coding as per IS, with multi stranded copper conductor 2.5 sqmm (Nominal area), single core, FRLSH PVC insulated and unsheathed stranded cable drawn through and including existing non metallic/mettalic heavy duty concealed/Surface conduit and including replacement of its fittings including all tees, bell mouth pieces and fixing accessories such as couplers, saddlers, pipe hooks etc, PVC junction boxes ISI marked with GI sunken boxes made out of 1.2mm thick of any module from 2 to 18 module confirming to IS-5139(pt-I) of 1969 and IS:14772-2000 with earth dolly coated with two coats of anti corrosive paint over a coat of red oxide primer internally and externally including modular cover plates with frame i.e. inner and outer plate extended upto 25 mm over sunken box for housing the modular switches, socket outlets, fan regulators etc with brass screws and brass washers and making good the disturbed surfaces as per existing for one light / fan / Bell point contorlled by one switch including 2.5 sqmm single core PVC insulated and unsheathed FRLSH copper cable, 1100 volt grade with multi stranded copper conductor green colour as earth continuity conductor upto common earth and connecting to common earth dolly with suitable size of lugs for one power point/ controlled by one MCB complete all as specified and directed

Supply and fixing temperature resistent SS braided pipe suitable to sustain pressure up to 8 bar not less than 60 Cm long suitable for out going / Hot water connections of Geyser with washer etc. complete as an directed.

NOTE:- Amount of credit of Rs. 74124.50 for retrieved materials is mentioned in Schedule of Credit Page No 21 & 22 of tender documents in pdf form which will be deducted offline while acceptance of tender.

M/S M S BUILDER AND CONTRACTORS (BID ID -3460349)

Ashwani Kumar (BID ID -3460889)