SPECIAL REPAIR TO KINGSLAY BLOCK AND EW-84 AT IMA DEHRADUN

Amount

Taking down cement plaster on brick or stone walling built in CM including raking out joints hacking for key scrubbing down by using mechenical means complete all as specified and directed.

M&L for Complete removal of existing treatment by brooming down or by steel wire brushes, scraping down smoke spots, moulds, moss and elllorescent salts, trading oil, gresey spots etc on wall complete all as directed by Engr in Charge

M&L for 5mm thick ready mix sand faced cement plaster on brick or concrete surfaces on ceiling, fascia roof projection etc as per manufacturers specification, surface finished even & fair, all complete upto the height of 7.5m complete all as specified and directed.

M&L for 15mm thick External ready mix sand faced cement plaster on brick or concrete surfaces including providing & mixing water proofing compound as per manufacturers specification, surface finished even & fair, complete all as specified and directed.

M&L for 10mm thick Internal ready mix sand faced cement plaster on brick or concrete surfaces including providing & mixing water proofing compound as per manufacturers specification, surface finished even & fair, complete all as specified and directed.

M&L for Providing and applying plaster of putty of 2 to 3 mm thickness over plastered surfaces on wall to prepare the surface even and smooth complete all as specified and directed.

M&L for applying two coats of 100% Premium acrylic emulsion paint on walls , facia , chajjas etc. having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new /Old surfaces ceiling and wall all as per manufacturers instruction complete all as specified and directed.

M&L for priming plastered and other surfaces with alkali resistant priming paint , to distampring on wall all as per manufacturers instructions and directed by EIC .

M&L for distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. Two or more coats on new/ old work to achieve the approved shade, complete all as specified and directed.

M & L for two coat white wash on old/new plaster surface of wall all as per manufacturers instructions and complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from frame) area n'exc 1.5 sqm complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter from frame) area exceeding 1.5 sqm but n.exc 4.00 sqm complete all as specified and directed.

Taking down and easing shutters to ensure smooth closing / opening including tightening of hinges, adjustement of tower bolts, sliding bolt and refixing in same opening etc area not exc 1 Sqm each complete all as specified and directed.

Taking down and easing of door shutters to ensure smooth closing/opening including resizing and tightening of hinges, adjustement of tower bolts, sliding bolt and refixing in same opening etc area exc 1 Sqm but not exc 2 Sqm each complete all as specified and directed.

Taking down and easing of door shutters to ensure smooth closing/opening including resizing and tightening of hinges, adjustement of tower bolts, sliding bolt and refixing in same opening etc area exc 2 Sqm each complete all as specified and directed.

Taking down shutters of any description n exc 1sqm each complete all as specified and directed.

Taking down shutters of any description exc 1 sqm and n exc 2 sqm complete all as specified and directed.

S&F Pieces ( 1st class hard wood TEAK) , small Let in for making good where hinges, sliding doors, handels ,etc . Have been removed from chowkhats or frames , joinery , etc incl painting or oiling to match , if required Mesicellaneous repairs complete all as specified and directed.

S&F in repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples with & including appropriate size of wooden beading of IInd class hardwood or iron fillet complete all as specified and directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples with & including appropriate size of wooden beading of IInd class hardwood or iron fillet complete all as specified and directed.

S & F 40mm thick 1st class H.W teak wood timber plain framed and arch shape on top paneled shutters (any number of decorative panels) with lock rail and panel of 15mm thick 1st class teak wood size of rail and stiles as per IS 1003 (part -I) kiln seasoned and chemical pressure treated complete all as specified and directed.

S & F 40mm thick 1st class H.W teak wood decorative plain framed glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc. (with sash bars), divided in to square, edges of framing plain, chamfered or rounded ,fitted with cut and mitered bead for securing glasses etc, window ventilators etc are provided with stiles and rails as specified in SSR Part-I, 1991, Section- 8, Clause 8.20 (a), complete all as specified and directed. Shutter shall be of factory made complete all as specified and directed.

S & F 30mm thick 1st class H.W teak wood decorative plain framed glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc. (with sash bars), divided in to square, edges of framing plain, chamfered or rounded ,fitted with cut and mitered bead for securing glasses etc, window ventilators etc are provided with stiles and rails as specified in SSR Part-I, 1991, Section- 8, Clause 8.20 (b), complete all as specified and directed. Shutter shall be of factory made complete all as specified and directed.

S & F Ist Class hard teak wood, Plain or semi circular at top chowkats & frame wrought rounded or chamfered put together with glue pinned joints and fixed complete all as specified and directed

S&F 18-19 mm thick prelaminated colour WPC sheet for cabinet shutter and frame & fixed at site colour as approved by Engr-in- Charge complete all as specified and directed.

S&F auto closing hinges 35mm of 0 crank openable at 110 degree for cabinet shutter fixed in repair complete all as specified and directed.

S&F Stainless steel handle 125mm size for cabinet shutter fixed in repair complete all as specified and directed.

M&L for 25mm 2nd class hard wood planed on side with but joints in ceilling boarding , supplied & fixed with nails in any situtation (except flooring and skirting) complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite ) soild door/ window Ceostory windows & other frame / chowkhat double patam of size 65 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Supension Grade) , calcium carbonate and natural fibers (wood powder / rice husk / wheaat husk ) and non toxic additives ( maximum toxicity index of 12 for 100 gms ) fabbricated with miter joints after applying PVC solvent cement and screws with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withrawal strength of 2200 N cum , (Face) & 1100 N (Edge) hold fast lugs of FI (40 x 5 ) mm, minimum compressive srength of 58 N/mm², modules of elasticty 900 N/ mm² and resitance to spread of flame of class A category with property of being termite / borer proof , water / moisture proof and fire retardant. and fixied in position with MS hold fast/ lugs / SS dash fasteners of required dia and length complete as per direction of Engineer-In-Charge.(M.S. hold fast/ lugs or SS dash fasteners be inclusive in the quoted rates) . Note : For WPC solid door/ window frames , minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable . Variation in profile dimension on plus side shall be accepetable but no extra payment on this account shall be made.

S&F factory made single extruded WPC (wood polymer Composite ) soild decorative type flush door shutter of size 30 mm thick comprising of virgin polymer of K value 58-60 (suspension Grade ), calcium carbonate and natural fiber (wood powder/ rice husk / wheat husk) and non toxic additives ( maximaum toxicity index of 12 for 100 gms ) having minimum density of 650 kg/cum and screw whithrawal strenght of 1800 N (Face ) & 900 N (Edge ) , minimum compressive strength 50 N/mm² , modulus of elasticity 850 N/mm² and resistance to spread of falme of Class A category with property of being termite /borer proof , water/moisture proof and fire retardant . WPC to be laminated with PVC foil of minimum 14 microns thic of approved desing pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel but hinges of required size with necessary full body threaded star headed counter sunk S.S screws., all as per direction of Engneer-In -Charge . ( Note : Stainless steel medium weight 3 Nos 100 mm long butt hinges and necessary S.S srews shall be inclusive in the quoted rates)

M&L for PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in bed blocks etc for embededding hold fasts complete all as specified and directed.

M & L for Providing, precast cement concrete PCC 1:2:4 type B-1 20mm graded in , cover slabs , shelves and similar articles with plain faces Gulli traps and mainhole covers complete all as specified and directed.

Hacking out old broken glass pane (any size thickness and description) from wooden frames / steel frames complete all as specified.

S & F 3 mm thick sheet glass ordinary quality glazing in square nexc. 0.5 sqm in each pane fixed with wooden moulding complete all as specified and directed.

M&L for french polishing on wooden surface of any discription width or girth including cleaning and preparing the surface including a coat of wood filler but one or more coat on new work to achieve the required finish complete all as specified and directed.

M&L for french polishing on wooden surface of any discription width or girth including cleaning and preparing the surface including a coat of wood filler but one or more coat on old work incl complete removal of exiting paint complete all as specified and directed.

S&F in repair floor door stopper 140mm of brass body and tougue with hard steel and spring complete all as specified and directed.

S&F floor door stopper 140mm of brass body and tougue with hard steel and spring complete all as specified and directed.

S & F Ist class teak wood moulding exc 3 sqcm & n exc 6 sqcm in cornices picture rails and the like complete all as specified and directed.

S & F Fancy and decorative type 300mm long brass barrel, semi barrel and skeleton tower flush bolts type 2 and fixed flush complete all as specified and directed.

S & F in repair Fancy and decorative type 300mm long brass barrel, semi barrel and skeleton tower flush bolts type 2 and fixed flush complete all as specified and directed.

S & F in repair Fancy and decorative type 150mm long brass barrel, semi barrel and skeleton tower flush bolts type 2 and fixed flush complete all as specified and directed.

S & F Fancy and decorative type 150mm long brass barrel, semi barrel and skeleton tower flush bolts type 2 and fixed flush complete all as specified and directed.

S & F 150mm butt hinges, cast brass with mild steel hing pin bright polished and fixed type B-11 complete all as specified and directed.

S&F 75 mm butt hinges, cast brass with mild steel hing pin bright polished and fixed type B-11 complete all as specified and directed.

S & F in repair Fancy and decorative type 300mm long brass sliding door bolt with sand or die cast brass hasp staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and directed.

S & F Fancy and decorative type 300mm long brass sliding door bolt with sand or die cast brass hasp staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed complete all as specified and directed.

S&F Stainless steel grating for nahani trap 100mm dia complete all as specified and directed.

S & F in repair Fancy type and decorative 150mm long extruded brass handles fabricated type polished complete all as specified and directed.

S & F Fancy type and decorative 150mm long extruded brass handles fabricated type polished complete all as specified and directed.

Dismantling floor, hearth or wall tiling /kota/udaipur marble/ granite stone tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for brick work using sub class "B" brick work straght or curvd on plan exc 6 mtr mean radius built in CM 1:4 (old size brick) including demolation of brick work complete all as specified and directed.

M&L for 25 mm thick cement concrete type B-1 , 1:2:4 ( 20mm graded aggregate as in sub base complete all as specified and directed.

M & L for Vitrified ceramic ( light shade), / designer tiles 10 mm thick (Square/rectangular ) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including screed bed or beading layer of morter 15mm thick in cement morter (1:6) for laying floor finishes complete all as specified and directed.

All as per item No 54 above but on vertical surfaces such as dado, skirting etc over and including 10 mm thick cement plaster finished even and rough to receive tiles in Cement mortar (1:4) complete all as specified and directed.

M & L for Vitrified ceramic dark shade double charge designer tiles 10mm thick (Square/rectangular ) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including screed bed or beading layer of morter 15mm thick in cement morter (1:6) for laying floor finishes complete all as specified and directed.

All as per item No 56 above but on vertical surfaces such as dado, skirting etc over and including 10 mm thick cement plaster finished even and rough to receive tiles in Cement mortar (1:4) complete all as specified and directed.

M&L for non skid ceramic coloured tiles area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm & 7 to 8 mm thick in floor set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with & including screed bed or beading layer of morter 15mm thick in cement morter (1:6) for laying floor finishes , complete all as specified and directed.

M&L for coloured glazed disigner tiles of size (1200 x 600 x 8 - 9) mm thick fixed with neat cement slurry in vertical surface to wall pointing in white/coloured cement to match over and including 10mm thick rendering in CM 1:4, complete all as specified and directed.

S&F stainless steel curtain rod, 25 mm dia, decorative including S S brackets, decorative finials at both ends complete all as specified including dismantling of existing rod.etc complete all as specified and directed.

M&L for Cutting chases, pinning in brick wall making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth complete all as specified and directed.

S&F medium grade steel water tubing, 15 mm bore galvanised with all fittings and fixed complete to walls or layed in floors including taking down of existing tubing and connections all as specified and directed

S&F medium grade steel water tubing, 20 mm bore galvanised with all fittings and fixed complete to walls or layed in floors including taking down of existing tubing and connections complete all as specified and directed.

Demolition and breaking up drain pipes, PVC pipes ,CI pipes (Salt glazed stoneware, AC or Reinforced concrete) set in cement mortar complete all as specified and directed.

S&F viterious china urinals half stall white incl CP urinal Spray Nozzal complete incl providing and fixing of plug bedding urinal against wall in cement motor 1:2 securing urinal to plug with and incl 60mm long brass screws pointing incl 60mm long brass complete all as specified and directed. Make : Cera Cat Pt No S4020112 / Jaquar Cat Pt No URS-WHT-13253N / Kohler Cat Pt No K-4978 IN-ER-0 alongwith all necessary accessories for proper functioning or equivalent make of group-I

S&F PVC (SWR), junction single, (Single T) 110 mm equal or unequal complete all as specified and directed.

S&F PVC (SWR), junction single, (Single T) 75 mm equal or unequal complete all as specified and directed.

S&F PVC (SWR), branch piece, (Single Y) 110MM equal or unequal

S&F PVC (SWR), branch piece, (Single Y) 75MM equal or unequal

S & F in repair PVC (SWR) Nahani trap ditto 100mm

M & L PVC (SWR) gully trap 125 / 110 mm, setting and jointing with solvent cement complete all as specified and directed.

S & F in repairs PVC (SWR) bend 110 mm any radius complete all as specified and directed.

S & F in repairs PVC (SWR) bend 75 mm any radius complete all as specified and directed.

M & L for 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches ,or in floor fixed in repair complete all as specified and directed.

All as per Item No 74 above but 75 mm dia on wall complete all as specified and directed.

S & F in repair vitreous China wash down water closet pan floor mounted single piece ( cascade) ceramic white including flushing cistern , plastic water closet seat , white colour pattren with flat bottom and cover complete all as specified and directed. Make : Cera Cat Pt No S1013216 / Jaquar Cat Pt No SLS-WHT-6851S220PP / Kohler Cat Pt No K-17629 IN-SM-0 alongwith all necessary accessories for proper functioning or equivalent make of group-I

S&F Vitreous china white Table Top Wash hand basin, one number brass CP waste coupling ,32mm dia , PVC waste pipe with connector fixed in repair complete all as specified and directed . Make : Cera Cat Pt No S2020153 / Jaquar Cat Pt No SLS-WHT-6601 / Kohler Cat Pt No K-28783 IN-SM-0 alongwith all necessary accessories for proper functioning or equivalent make of group-I

M&L for 16 - 18mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills,cooking platforms, shelves in cupboard,handwash places and like including necessary cutting and grooving to walls and making good by pointing in cement mortar (1:2) using admixture of pigment to match with shade of granite over and including cement screed bed Cement Mortar (1:6) 15 mm thick colour of granite as approved complete all as specified and directed.

M & L for Granite stone any decripition providing edges moulding to 16-18mm thick granite stone of counters vanities etc . including machine polishing to edge to give high gloss finish etc complete all as specified and directed.

S&F Hot and cold long body single mixer mixer fancy type complete all as specified. Make : Cera Ruby series / Jaquar Opal prime series / Kohler Accliv series or equivalent make of group-I

M&L for provision at point of contact of wood work of chemical emulsion (in oil or kerosene based solution ) @ 0.5 ltrs /hole by drilling hole at dowanrard angle of 45 digree at 150mm centre to centre and sealing the same complete all as specified and directed.

M&L treating of soil under existing floors using emulsion @ one liters per hole , 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse send ) to match the existing floors complete all as specified and directed.

S&F PVC connection , reinforced 450mm long 15mm in size with brass check nut and PVC washers at both ends complete all as specified and directed.

S&F 15mm Angle stop valves, fancy type chromium plated, screwed down, high pressure with wall flange and fixed in repair complete all as specified and directed. Make : Cera Ruby series / Jaquar Opal prime series / Kohler Accliv series or equivalent make of group-I

S&F Bib tap cast copper alloy , chromium plated suitable for 15mm bore iron pipe with long body fancy type with wall flange and fixed in repair complete all as specified and directed. Make : Cera Ruby series / Jaquar Opal prime series / Kohler Accliv series or equivalent make of group-I

S&F in repair 15mm brass CP wall Mixer for mixing hot & cold water with provision of over head shower screwed down for iron pipe and fixed complete all as specified and directed. Make : Cera Ruby series / Jaquar Opal prime series / Kohler Accliv series or equivalent make of group-I

S&F brass chromium plated shower rose with or without swivel joints including 200 mm long shower arm fixing to steel pipe or union fixed in repairs complete all as specified and directed. Make : Cera Cat Pt No F7010210SS / Jaquar Cat Pt No OHS-35495 / Kohler Cat Pt No K-22645 IN-CP alongwith all necessary accessories for proper functioning or equivalent make of group-I

S&F Brass stainless steel tower rail 60cm long between flanges fixed in repair complete all as specified and directed. Make : Cera Cat Pt No F5013103CH / Jaquar Cat Pt No AKP-35711PS / Kohler Cat Pt No K-25065 IN-CP alongwith all necessary accessories for proper functioning or equivalent make of group-I

S&F brass chromimum plated Towel ring fixed with and including Chromium plated brass screws and wooden / plastic cleats complete fixed in repair complete all as specified and directed. Make : Cera Cat Pt No F5014105CH / Jaquar Cat Pt No CPA-1121RD / Kohler Cat Pt No K-5631 IN-CP alongwith all necessary accessories for proper functioning or equivalent make of group-I

S&F Brass chhromium plated tubular Towel Rack with Lower Hanger (Stainless Steel) fixed in repair complete all as specified and directed. Make : Cera Cat Pt No F5015131CH / Jaquar Cat Pt No ACN-1181S / Kohler Cat Pt No K-17529T-CP alongwith all necessary accessories for proper functioning or equivalent make of group-I

S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.00 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed. Make : Cera Cat Pt No F8030103 / Jaquar Cat Pt No ALD-587 / Kohler Cat Pt No K-97258 IN-CP alongwith all necessary accessories for proper functioning or equivalent make of group-I

S&F fixed in repair Toilet paper holder stainless steel complete all as specified and directed. Make : Cera Cat Pt No F5015109CH / Jaquar Cat Pt No ACN-1151N / Kohler Cat Pt No K-5633 IN-CP alongwith all necessary accessories for proper functioning or equivalent make of group-I

S&F fixed in repair Soap dish stainless steel complete all as specified and directed. Make : Cera Cat Pt No F5003106 / Jaquar Cat Pt No ACN-1131N / Kohler Cat Pt No K-25068 IN-CP alongwith all necessary accessories for proper functioning or equivalent make of group-I

S&F Sheet glass corner shelf with chromium plated bracket guard and railling fixed in repair with brass screws and rawl plug complete all as specified and directed. Make : Cera Cat Pt No F5005102 / Jaquar Cat Pt No CPA-1173 / Grohe Cat Pt No 40809000 alongwith all necessary accessories for proper functioning or equivalent make of group-I

Blank

S & F in repair for 0.75 mtr X 0.90 mtr frameless bevelled edge looking mirror 5.5mm thick fixed with plugs with chromium plated brass screw and cup washer complete all as specified and directed.

S&F 2000 liter rotational moulded polyethylene water storage tank triple layered (cylinderical vertical with closed top )hoisted and fixed in position including dismantling of existing tank of any description complete all as sepcified and ISI Marked complete all as specified and directed.

Demolition of cement concrete in ground floor and paving not exc 15cm thickness (below or above ground level) and removing surplus spoil out of Defence Land complete all as specified and directed

M&L for 75 mm thick PCC (1;3:6) type C-1 as in plinth protection/ Path finished even and smooth without using extra cement complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 using 40 mm graded stone aggt as in sub base filling and mass concrete complete finished evenand fair complete all as specified and directed.

M & L for chequered heavy duty glossy finish cement concrete tiles 30cm X 30cm X 25 mm thick, set, jointed & pointed in neat cement slurry in floor with grey cement mixed with colour pigments complete all as specified and directed.

M & L for 20 mm thick screed bed or bedding layer of mortar in 1:6 for laying of flooring complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 18-20 mm thick over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified.

M&L for machine cut kota stone slab flooring 18-20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified.

M&L for 100 mm thick PCC (1:4:8) Type D2 using 40 mm graded stone aggregates as in foundations filling and mass concrete.

M&L for sand cushioning under floors including watering and consolidation . complete all as specified and as directed.

S& F coloured machine vibro mechenically floated glossy finish interlocking cement paver block,any shape and size confirming to IS 15658-2006 of 60mm thickness,M-35 Grade with,topping of cement mixed with pigment,colour and shape shall be approved by engr-in-charge ISI Marked.

M&L Providing precast cement concrete block masonary with soild blocks, exc.10cm in width and setting in cement mortar , kerbs stone all as directed, 1:2:4 mix type B-1 complete all as specified.

M&L Struck or recessed pointing , to brick wall that involves filling raked cement mortar joints CM 1:3 with mortar to ceate a concave groove complete all as specfied by EIC

Dismantling timber scantling 40scm and over in section in any position framed work complete all as specified.

S & F MS framed work as in doors or gates of angle or other section with gusset plates , rails, brackets etc complete drilled for fixing of steel sheeting or others covering. Doors , etc to be prepared for hanging or sliding with and incl either hooks and hinges or steel hanging door fitting and hanging also fastening and fixing complete all as specified and directed.

S & F Mild steel sheet ,plain sheet 1.00 mm thick in , steel gate and similar work , cut to size , holes punched : including round headed screws, clout nails or rivits and fixing to wood or steel framing with plain 40mm lap joint with riveted or welded seams , including bending or turning up, mitred angles etc. as required complete all as specified and directed.

M & L for Prepration of new steel surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M & L for Prepration of old steel surface of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

S&F MS angle/TEE/Hollow/tubular section as in main and cross beams, hips and jack rafter, purlins where connected to common rafters and etc. all as directed by engr- incharge confoming to Fe-410- W(Gde- E-250) quality- B complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulb, insulation etc) or insulation boards slabs/blankets any thickness including cover fillets and framework all as specified and as directed.

Material and labour for suspended false ceiling using E-grid 2430, 180 GSM (exposed ceiling suspension system) of grid size 600mmx600mm with main runner 38 mm x 24 mm and wall angle 24mm x 24mm using 4mm thick high Pressure Non Asbestos Fiber Cement decorative Board (E-Board Classic) in a grid of GI systtem duly suspended with 4 mm dia GI bar hanger fixed with steel dash fasteners or iron purline from the roof with adjustment clip providing positions for light fixtures, air conditioning diffuser and ducts, sprinkler, smoke detectors etc. The main runners to be secured to structural soffits by hanger @ 1220 mm maximum c/c. The last hanger at the end of each main runner should not be interlocked between main runners @ 610mm c/c, as to form 600 mm x 600 mm grid all as specified and directed.

Dismantling of asbestos cement / GI sheets (any pattern) as in roof covering all as specified and directed.

S&F AZ 150 grade pre-painted galvalume aluminium zinc coated GI based Plain steel sheet 0.50mm thick any colour having tensile strength of 550 Mpa as in roof covering/ridge/ cladding to wall fixed with self tapping screws complete all as specified and directed. When fixed in redges, the profile of sheet should match the profile of roof sheets

S&F AZ 150 grade pre-painted galvalume aluminium zinc coated GI based tile profile / corrugated steel sheets (as required) 0.50mm thick any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed.

M & L for Chipping off existing loose, damaged concrete from RCC members of all affected RCC Columns, beams, slabs and chajjas on external and internal facades etc beyond main r/f.(if required), carefully with chisel and hammer. Providing and applying Rust passivator to existing r/f bars including wire brushing of r/f, cleaning, washing of concrete etc complete all as specified and directed.

M & L for steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns/beams, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for Carry out application of 'Bi-polar migratory corrosion inhibitor' of approved make on concrete surface through pores of concrete, inhibiting the corrosion and de-passivating the Electro-chemical reaction complete all as specified and directed.

M & L for Providing and applying effective polymer bonding coat of approved make between old and new concrete after cleaning, drying & applying as per manufacturer's instruction complete all as specified and directed.

M & L for Repairing concrete areas using non shrink, free flow, corrosion inhibiting microconcrete. Rebuilding the section of damaged RCC elements to its original size by providing and casting with microconcrete of grade M40 all lead lift, mixing, placing, levelling the surface complete as per manufacturer's specification complete all as specified and directed.

M & L for Cutting channels, grooves and filled with mortar admixed with multifunctional acrylic polymer emulsion in the ratio of 1:2:3 or rebates n exc 15cm girth and trimming surface with or without reinforcement all as per manufacturer's direction complete all as specified and directed.

Supply, mixing and application two component structural grade polymer modified reinstatement mortar, where local spalling has taken place or shuttering is not possible . The mortar can be applying in layers not exceeding 6mm thick in each layer in and upto any thickness in smaller vertical pockets and upto any thickness in horizontal applications. The mortar should have a minimium compressive strength 12N/mm2 in 1 day and 45N/mm2 in 28 days. Minimum flexural strength should be 8 N/mm2 in 28 days. A modified styrene butadience emulsion for use as a bonding aid and gauging liquid for cementious system to be mixed with cement slurry before the application of modified polymer mortar to be used @ 6 ltr/bag of cement. The bonding agent should have minimium compressive strength 24N/mm2. Minimum tensile strength 3.5N/mm2, minimium flexural strength 6.5N/mm2 complete all as spd and directed by the Engr-in-charge upto 25 mm average thickness and upto 4 storey High. NOTE:- Cement and sand morter in proportion of 1:2 graded coarse sand ) with polymer admixed in proportions approved by Engr-in-charge)

S&F single extruded PVC/WPC louvers of approved colour for ceilings, interior wall panelling , etc the louvers shall have dimensions of 2900mm x 10mm x 24mm with a toleance of 5% fixed on GI grid and with 4mm supended hanger wire . The compostion shall include virgin polymer with a K value of 58-60 (suspension grade ), calcium carbonate , natural fibres ( such as wood powder, rice husk , or wheat husk ) , and non - toxic additives, having class A category resistance to spread of flame criteria , louvers must be termite / borer proof , water / moisture proof and fire retardant complete all as directed

Applying bituminous primer on roof surfaces @ 0.40 ltr/sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 kg/sqm and provide modified polymeric five layered APP (Atactic Polypropylene) Modified Polymeric Membrane with 100 micron high molecular high density polythylene film. Min wt of memebrane will be 3.5 kg/sqm and bonded completely to the surfaces with min end overlap of 15 cms and side lap 75 mm (overlaps to be bounded with thermo fused by flame) and over APP applying one coat of hot blown bitumen 85/25 @ 1.2 kg/sqm blinded with fine sand in dry condition @ 0.5 kg/sqm and applying aluminium Paint all as specified and directed by Engr-in-Charge.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surface of walls, floors, etc. complete all as specified and directed.

Taking down water Heater of any capacity and make serviceable by replacement unsv part ie thermostats / heating element including descaling the inner container with cleaning solution including preparation of old painted surface body of geyser of any capacity ,cleaning foreign material ,filling cavaties atc and painting with one coat of synthetic enammeled paint by spray painting and marking MES No. with paint and kept in safe custody and refixing at site after compltion of wiring work complete all as specified and directed.

Taking down old U/S main switches, Sheet metal enclosures DB including MCCBs, MCBs etc including making good to the disturbed surface of wall complete all as specified and directed.

Taking down old unsv Tube Light, Lamp,Security light of any size and capacity complete all as specified and directed.

Taking down existing ceiling fan of any capacity and make serviceable by replacement unsv part ie capacitor / bush bearings and preparation of old painted surface body and blades of ceiling fan of any capacity ,cleaning foreign material ,filling cavaties atc and painting with one coat of synthetic enammeled paint by spray painting and marking MES No. with paint and kept in safe custody and refixing at site after compltion of bldg work complete all as specified and directed.

Taking down carefully submain wiring including all accessories without disturbing existing wiring fittings fixtures etc and making good to the disturbed surfaces all as directed and as specified in any type and size complete all as specified and directed.

Material and labour for point wiring with PVC insulated and unsheathed electric cable 1100 volts grade single core FRLSH having multi stranded copper conductor of 1.5 sq mm nominal cross sectional area drawn in Non metalic pvc conduit not less than 25mm dia concealed in wall with all fitting and fixing accessories and 1.5 sq mm PVC insulated unsheathed multistranded copper conductor cable as continuous earth conductor, connected to earth dolly by providing suitable lugs with & including modular metal flush box of required size factory made for mounting Modular switch, regulators etc with and including Modular cover and frame , ISI marked, for the following . Note (i) The quoted rates shall be deemed to be inclusive for making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. (ii) Point wiring & earth wire shall be connected to each & every sunken box. (iii) 1 x 5 Amps Independent board in one circuit of 1.5 sqmm and 1 x 16 Amps Socket board in one circuit 2.5 sqmm and 4 sqmm be prepeared . (vi) Wiring insulation test result sheet after carryng out the internal wiring must be prepared by contractor and the rate for the same deemed to be inclusive tin the quoted rate. .

One light point controlled by one, one way switch 5 Amps

One fan point/ exhaust fan point controlled by one, one way switch 5 Amps

One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent board.

One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

One bell point controlled by one, bell switch 5 Amps

All as per item No.136 above but with stranded copper conductor 2.5 Sq mm (nominal area), two single core, PVC insulated cable 1100 Volt grade ISI-694 marked for 3 pin, 15 Amp socket outlet, independent, including PVC insulated stranded copper conductor 2.5 Sqmm (nominal area) single core as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed.

Supply and fix modular switch 1 way 6/10 A, 1 Module complete all as specified and directed.

Supply and fix modular switch 1 way 16/20A, 1 Module with indicator lamp complete all as specified and directed.

Supply and fix modular bell push 6A, 1 Module complete all as specified and directed.

Supply and fix modular socket 6/10A, 2/3 pin combined 2 Module complete all as specified and directed.

Supply and fix modular socket 16/20A, 2/3 pin combined 2 Module complete all as specified and directed.

Supply and fix modular fan regulators step type 2 module 120W complete all as specified and directed.

Supply and fix lamp holder PVC /Polycarpebonated type with back plate suitable for batten fittings complete all as specified and directed.

Material and labour for ceiling rose, 63.5 mm dia, ISI marked, three terminal of polycarbonate/isolated body complete all as specified and directed.

Suply and fix for Bell Electric Ding dong type suitable for operation on 230 volt 50 HZ A C supply complete all as specified and directed.

Supply and fixing LED lights fitting 1x 22W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete

Supply and Fix LED street/Security wall mounted light fitting of 25 Watt ,Epoxy powder coated with any additional treatment for smooth and anti corrosive finish, fully diffused ,connected the same with using PVC sheathed , insulated 3 core flexible 23/0.0076 copper cable including fixing arrangement for fixing the light fitting to ceiling rose complete all as specified and directed.

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete

Supply and fix florette WL1E27 SS decorative wall ,stainless steel ,rust free fixture with white glass diffuser suitable for 9 LED lamp and connected the same with using PVC sheathed and insulated 3 core flexible 23/0.0076 copper conductor cable including all accessories and fixing arrangement for fixing the light fitting to wall complete all as specified and directed.

Supply and fix ceiling Fan complete with blades,down rods ,230 volts ,1200 mm sweep ,min air delivery 210 CFM with service value 6.00 BEE ,with Brushless direct current motor (BLDC) including taking down old unsv serviceable fan and deposited to the store complete all as specified and directed.

S & F sub main wiring with 2 run PVC insulated unsheathed FRLSH cable 1100 Volt grade, with multi stranded copper conductor drawing in existing Concealed conduit including one run PVC insulated unsheathed cable with multi stranded copper conductor as a earth continuity and connected upto DB of following sizes 2 x 10 Sqmm + 1 x 10 sqmm ( for power DB ) complete all as specified and directed. Note:Two run of single core PVC cable 10 Sqm, One run of 10 Sqmm earth cable and one run of PVC condiut shall be measured and paid as one unit.

S & F sub main wiring with 2 run PVC insulated unsheathed FRLSH cable 1100 Volt grade, with multi stranded copper conductor drawing in existing Concealed conduit including one run PVC insulated unsheathed cable with multi stranded copper conductor as a earth continuity and connected upto DB of following sizes 2 x 4 Sqmm + 1 x 4 sqmm ( for power DB ) complete all as specified and directed. Note:Two run of single core PVC cable 4 Sqmm, One run of 4 Sqmm earth cable and one run of PVC condiut shall be measured and paid as one unit.

Supply and fix exhaust Fan ,made of sturdy Engineering plastic complete with louvers shutter,voltage 230volts ,50HZ,RPM 1200,copper winding of sweep 250mm including cutting holes on wall and making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface complete all as specified and directed.

S&F Water heater (Geyser) storage type, electric,capacity 40 litres horizontal type five star rated AC SP 230 volts, 50 Hz, vertical mount type, shockproof and rustproof metal body, stainless steel inner container, high efficiency heating element, autocut thermostate, pressure release safety system,NRV , fire retardent cable with 3 pin plug top, white colour including fixing accessories like fastensers, nuts, washers including taking down old unsv serviceable Geysers and deposited to the store complete all as specified and directed.

Material and labour for earthing with galvanised steel earth plate electrode 60cmX60cmX 6mm thick burried directly in ground (earth pit not less than2.25 mtr below ground level) with top edge of the plate not less than 1.5 mtr below ground level connected to 4mm thick GI wire by means of nuts,bolts,check nuts & washers of galvanized iron or steel,protected by 15mm bore light grade galvanised iron pipe and connected to main switch board,including all necessary excavation & earth work in hard dense soill including funnel with wire mesh and watering pipe 20 mm bore medium grade galvanised iron pipe with charcoal and common salt in alternate layers of 15 cm thickness all around the GI plate electrode with concrete pit in PCC 1:3:6 type C-1 with cast iron frame including cast iron cover10mm thick hinged to CI frame and 6mm MS rod for handle and necessary testing complete all as shown in electrical plate No 3 of SSR part-I complete all as specified and directed.

Blank

S & F MCB DB complying with IEC 61439 -1 & 3., sheet metal enclosures double door .The DBs should be supplied with tin platted insulated copper bus bar rated for 100A. 240 volts 2 in 1 shutter (Metal Door) with IK09 type with blanking plates where required and IP 43 degree protection, the DB door should be hinged type and possible to reversible at site.The DB door shall have overhang, to gel with wall properly.The DB shall be supplied with all insulated N. Bar riveted on Din channel frame and should not restrict cable entry from top or bottom.The DB shall have plastic knobs on shield to hold complete all as directed. All the above mentioned specs the technical documents from OEM shall be provided at the time of bidding of following capaity MCB DB SPN,18 ways complete all as specified and directed.

S & F MCB DB complying with IEC 61439 -1 & 3., sheet metal enclosures double door .The DBs should be supplied with tin platted insulated copper bus bar rated for 100A. 240 volts 2 in 1 shutter (Metal Door) with IK09 type with blanking plates where required and IP 43 degree protection, the DB door should be hinged type and possible to reversible at site.The DB door shall have overhang, to gel with wall properly.The DB shall be supplied with all insulated N. Bar riveted on Din channel frame and should not restrict cable entry from top or bottom.The DB shall have plastic knobs on shield to hold complete all as directed. All the above mentioned specs the technical documents from OEM shall be provided at the time of bidding of following capaity MCB DB SPN,12 ways complete all as specified and directed.

S & F sheet metal enclosure, single pole and neutral with two pin and earth plug and socket with and including one single pole MCB 20 Amps, , complying to IS/IEC 60898, 240 volts 'C' Curve 10 KA with energy limiting class 3. The MCB shall have 50% lower watt loss as required by IS/IEC 60898 from 6A to 63A . The mcb shall have the unique property of di-electric strength, arc resistance, insulation, flame retardancy and temperature resistance, including connection with suitable size copper lugs, The MCB shall give visible flag indication when MCB trips on Short Circuit Fault. The MCB shall have safety shutter to avoid any wrong insertion of cable. The MCB shall have the termination capacity of 35 Sq mm. The MCB shall have electrical life 20,000 operations up to 32A and 12,000 operation up to 63A including connection with suitable size copper lugs complete all as directed. All the above-mentioned specs technical documents from OEM shall be provided at the time of bidding

S & F MCB SP complying to IS/IEC 60898, 240 volts 'C' Curve 10 KA with energy limiting class 3. The MCB shall have 50% lower watt loss as required by IS/IEC 60898 from 6A to 63A . The mcb shall have the unique property of di-electric strength, arc resistance, insulation, flame retardancy and temperature resistance, including connection with suitable size copper lugs, The MCB shall give visible flag indication when MCB trips on Short Circuit Fault. The MCB shall have safety shutter to avoid any wrong insertion of cable. The MCB shall have the termination capacity of 35 Sq mm. The MCB shall have electrical life 20,000 operations up to 32A and 12,000 operation up to 63A including connection with suitable size copper lugs complete all as directed. All the above-mentioned speification/ technical documents from OEM shall be provided at the time of bidding of following capaity. MCB SP 240 volts, 50 Hz capacity 6-32 Amps complete all as specified and directed.

S & F MCB SPN complying to IS/IEC 60898, 240 volts 'C' Curve 10 KA with energy limiting class 3. The MCB shall have 50% lower watt loss as required by IS/IEC 60898 from 6A to 63A . The mcb shall have the unique property of di-electric strength, arc resistance, insulation, flame retardancy and temperature resistance, including connection with suitable size copper lugs, The MCB shall give visible flag indication when MCB trips on Short Circuit Fault. The MCB shall have safety shutter to avoid any wrong insertion of cable. The MCB shall have the termination capacity of 35 Sq mm. The MCB shall have electrical life 20,000 operations up to 32A and 12,000 operation up to 63A including connection with suitable size copper lugs complete all as directed. All the above-mentioned speification/ technical documents from OEM shall be provided at the time of bidding of following capaity MCB SPN 240 volts, 50 Hz of capacity 40 Amps complete all as specified and directed.

S & F MCB SPN complying to IS/IEC 60898, 240 volts 'C' Curve 10 KA with energy limiting class 3. The MCB shall have 50% lower watt loss as required by IS/IEC 60898 from 6A to 63A . The mcb shall have the unique property of di-electric strength, arc resistance, insulation, flame retardancy and temperature resistance, including connection with suitable size copper lugs, The MCB shall give visible flag indication when MCB trips on Short Circuit Fault. The MCB shall have safety shutter to avoid any wrong insertion of cable. The MCB shall have the termination capacity of 35 Sq mm. The MCB shall have electrical life 20,000 operations up to 32A and 12,000 operation up to 63A including connection with suitable size copper lugs complete all as directed. All the above-mentioned speification/ technical documents from OEM shall be provided at the time of bidding of following capaity. MCB SPN 240 volts, 50 Hz capacity 63 Amps complete all as specified and directed.

S & F MCB SP complying to IS/IEC 60898, 240 volts 'C' Curve 10 KA with energy limiting class 3. The MCB shall have 50% lower watt loss as required by IS/IEC 60898 from 6A to 63A . The mcb shall have the unique property of di-electric strength, arc resistance, insulation, flame retardancy and temperature resistance, including connection with suitable size copper lugs, The MCB shall give visible flag indication when MCB trips on Short Circuit Fault. The MCB shall have safety shutter to avoid any wrong insertion of cable. The MCB shall have the termination capacity of 35 Sq mm. The MCB shall have electrical life 20,000 operations up to 32A and 12,000 operation up to 63A including connection with suitable size copper lugs complete all as directed. All the above-mentioned speification/ technical documents from OEM shall be provided at the time of bidding of following capaity. MCB SP 240 volts, 50 Hz capacity 63 Amps complete all as specified and directed.

S & F Distribution boards epoxy powder coated TP & N (VTPN MCCB DB) fabricated from minimum 1.6 mm thick CRCA sheet and fixed/ flush to wall and suitable for universal mounting with 250 Amps fully insulated copper Bus Bar for each phase and 02 neutral shrouded bar ,2 earth bar and cable tie for cable management with reversible door for IP-43 DB,S protection,415 volt ,for fixing of suitable size of FP MCCB as incomer and 12 Nos MCBs SP or 4/8/ 12 TP MCBs (or any combination of SP/TP MCBs) outgoings of following capacity and making good the distrubed surface 4 Way VTPN DB (FP MCCB +12 MCB,C) complete all as specified and directed. Note: Suitable MCCB and outgoing MCBs will be measured separately under relavant items of this schedule)

S & F Distribution boards epoxy powder coated TP & N (VTPN MCCB DB) fabricated from minimum 1.6 mm thick CRCA sheet and fixed/ flush to wall and suitable for universal mounting with 250 Amps fully insulated copper Bus Bar for each phase and 02 neutral shrouded bar ,2 earth bar and cable tie for cable management with reversible door for IP-43 DB,S protection,415 volt ,for fixing of suitable size of FP MCCB as incomer and 36 Nos MCBs SP or 4/8/ 12 TP MCBs (or any combination of SP/TP MCBs) outgoings of following capacity and making good the distrubed surface 12 Way VTPN DB (FP MCCB +36MCB,C). complete all as specified and directed. Note: Suitable MCCB and outgoing MCBs will be measured separately under relavant items of this schedule)

S & F MCCB ,4 pole ICS=100% ICU at 415 volts with rupturing capacity 16 KA with thermal-magnetic release and adjustable overload setting . The MCCB shall have a Mechanical life = 40000 operations & Electrical life = 8000 operations of capacity 100 Amps complete all as directed.

S & F MCCB ,4 pole ICS=100% ICU at 415 volts with rupturing capacity 16 KA with thermal-magnetic release and adjustable overload setting . The MCCB shall have a Mechanical life = 40000 operations & Electrical life = 8000 operations of following capacity 160 Amps complete all as directed.

Supply and fix concealed in wall Rigid non metalic PVC conduit of 25mm dia , inclusive of boxes (junction/terminal) but inclusive of all tees,bend ,elbow reducers, bell mouth tube ends and fixing acessories such as couplers,lock,nut saddles,pipe hooks complete all as specified and directed. ( For for drawing Point wiring cable /Submain cable where conduit is open on wall / conduit got damged in conceale / Blocked /For tele/LAN wire) Note : The rate for cutting and chasing of wall to flush the conduit and making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface shall deemed to be included in the quoted rate .

S & F surface spot light with alluminium structure with adjustable light engine to achive the desired illumuination of 10w.

Taking out old Unsv LT UG cable of any size doing excavation in ground complete all as specified and directed.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 630 sq mm 3 1/2 core. complete all as specified and directed.

All as per item No 173 above but of size 240 Sqmm x3.5 Core. complete all as specified and directed.

All as per item No 173 above but of size 150 Sqmm x3.5 Core complete all as specified and directed.

All as per item No 173 above but of size 95 Sqmm x3.5 Core complete all as specified and directed.

All as per item No 173 above but of size 70 Sqmm x3.5 Core complete all as specified and directed.

All as per item No 173 above but of size 50 Sqmm x3.5 Core complete all as specified and directed.

All as per item No 173 above but of size 35 Sqmm x3.5 Core complete all as specified and directed.

All as per item no 173 above but of size 16 Sqmm x 4 Core complete all as specified and directed.

All as per item No 173 above but of size 10 Sqmm x 2 Core complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundations, or for shafts, wells, cesspits, manholes, pier holes, etc. and not exceeding 10 Sqm on plan and getting out in any type of soil complete all as specified and as directed

Returning filling including spreading leveling, watering and well ramming in layers not exceeding 25cm in soft/loose soil complete all as specified and as directed.

M&L for sand cushioning to UG cables (8 cm deep before laying of cable and 15cm deep over the cable) complete all as specified and directed. Note : Punned thickness will be measured.

Suppy and laying un-reinforced precast cement cable cover ,cass LV,type -I flat size 250x150x40mm complete all as specified and directed.

Removing excavated soil to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and as directed.

Supply and laying Tube light grade galvanised 100 mm dia with all fitting ,Laid in ground for crossing the cables across the road by cutting existing roadv , under floor by cutting existing floor and making good the road /floor surface after laying of pipe complete all as specified and directed.

Supply and laying LDPE pipes 50 mm dia with all fitting ,burried upto 45cm in ground for crossing the cables in ground from LT panel complete all as specified and directed.

Supply installing, erecting commissioning and new factory made LT panel Board outdoor type, 415V, 3 phase & 4 wire system, cubical of suitable size for housing of all equipments & proper heat dissipation, CPRI approved weather / Dust proof made out of 3.15 thick CRCA sheet powder coated with front and back side openable with suitable cable alley protected with Bakelite sheet between bus bar & cable alley with front side shutters with locking arrangement, including Aluminum bus bar insulated with colour coaded heat shrinkable sleeve of rating not less than 1.5 times the rated capacity of the incomer MCCB and bus bar chamber covered both side using bakelite sheet partition and wire mesh on back side of cable alley for the protection purpose. All type Test certificates and Design verification with switch gears (as per confirming to IS/IEC-61439/2011 part-I and part-2 with short circuit test at 65 KA should be submitted by the contractor before executing the job. The Bus bar shall be mounted on F clars insulators with intervals not more than 500mm. All inter connections between the main Bus bar as well as incoming / outgoing feeders shall be carried out with TPN Aluminum bus bars of rating not less than 1.5 times rated capacity of individual outgoing feeders. All control wiring shall be with FRLS PVC insulated 2.5 Sqmm multi-standard copper conductor and shall be properly bunched. The panel board shall have bottom channel of size 75 x 40 mm properly welded with 45 cm long of 04 legs of angle iron 50 x 50x6 mm using 3 mm thick CRCA sheet corners to all legs and complete mounted or fixed on PCC foundation above 0.45 mtr on floor and cable connection with suitable size of Aluminum lugs and suitable size of chrome plated brass double compression glands provided for incoming and outgoing cables comprising the following:-

Material and labour for earthing with galvanised steel earth plate electrode 60cmX60cmX 6mm thick burried directly in ground (earth pit not less than2.25 mtr below ground level) with top edge of the plate not less than 1.5 mtr below ground level connected to 32 X 6 GI STRIP by means of nuts,bolts,check nuts & washers of galvanized iron or steel,protected by 15mm bore light grade galvanised iron pipe and connected to main switch board, including all necessary excavation & earth work in hard dense soill including funnel with wire mesh and watering pipe 20 mm bore medium grade galvanised iron pipe with charcoal and common salt in alternate layers of 15 cm thickness all around the GI plate electrode with concrete pit in PCC 1:3:6 type C-1 with cast iron frame including cast iron cover10mm thick hinged to CI frame and 6mm MS rod for handle and necessary testing complete all as shown in electrical plate No 3 of SSR part-I all as specified and directed.(Two earthing for each main Panel )

Supply and Fixing LED Bollard fittings,360 degree light distribution model LIARA 1 mtr length, including connected accessories all as conforming to the following parameters: - (i) System watt/Lumens: - Max-10 watts/total system lumen not less than 100 lm (ii) Housing: - High pressure die cast aluminium. (iii) IP Rating & IK Rating: - IP 65 (iv) Front cover: - Polycarbonated Cover for More protection (v) Mounting: - On the surface (vi) Finish: - Epoxy powder coated with any additional treatment for smooth and anti corrosive finish. (vii) Lamp: - High bright LED (viii) System Efficacy (lm/W) of the luminaries: - Not less than 100m/watt. (ix) Colour temperature (K): - Not less than 5700 (x) Color Rendering Index (CRI): - Not less than 70 (xi) Life: - Not less than 25000 Hrs of operation (xii) Optics: - Polycarbonate Diffuser (xiii) Control gear: - PF not less than 0.90 and THD less than 20% at full load with operating voltage 140-270V AC, 50 Hz.

Cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate in foundations, filling and mass concrete complete for making foundation for mounting flood light /bollard light fitting/finishing of roads/floors etc .

Cutting of road /floor surface 30cm girth, up 45 cm width for croosing the pipe line /laying of cable acroos the road all as specified and directed.

Supply and erection in truely vertical position steel tubular swaged poles, type 410 SP-31 (9.00 meters long) with cast iron base frame, finial taper plug, bolts, nuts and screws all as specified including factory painted with two coats of black bituminous paint internally through out and externally for embedded portion and making 30 cms wide strips with yellow and black paint at alternatively upto 1.50 metre height and applying two coats of aluminium paint over a coat of red oxide primer on remaining exposed surface after erection , including writing of pole number complete all as specified and directed by the Engr-in-Charge. Note: (1) All excavation & earth work as involved shall be measured & paid seprately. (2) PCC foundation and Coping as involved shall be measured and paid seprately under respective items.

Supply and fixing LED street light fitting 60 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete.

M&L for cement concrete type B-1, 1:2:4 TYPE B-2 (20mm graded stone aggregate) for coping above gound level of pole .

Supply and fix thermoplastic cercuit breaker box IP 65 protection with metric knockouts for cable entry one row four modules of size 126x228x111 mm with DIN channel and one No MCB SP 6 to 32 Amps and four connectors of 2.5 Sqmm without glands and with clamps Make :- HENSEL Cat KV-7104 or equivalent.

S& F Wiring for submain alongwith earth wire 2x 2.5+ 1x2.5 sqmm of FR ,PVC insulated copper conductor, single core cable in surface as required

M& L for taking down old rusted /damageged rising main pipe line of any dia from all block

M&L laying Tubes, 'Medium grade grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in /Trench floors of dia 40mm.

Supply anf fixing Gun-metal,gate valves of dia 40mm, with iron wheel head, screwed both ends for iron pipe and fixed

Construction of brick masonary valve pit chamber of size (600x600x600) mm (internal dimension ) in non expansive soil with and including necessary excavation and earth works in any type of soil, MS sheet cover with MS frame with lockong arrengement, painting , all as specified complete.

Note : Tenderers may note that amount of credit Rs 6,41,935.00 will be deducted from the total amount arrived, at the time of Acceptance of contract.

V r traders (BID ID -3387310)

M/s Chitter Mal & Co. (BID ID -3385369)

M/S SURAT SINGH AND SONS (BID ID -3387461)

RAMAPATI ENGINEERING SERVICES (BID ID -3386928)

M/s DHARAM VIR GHAI (BID ID -3387019)

Ms dev associates (BID ID -3384885)

PAWAN KUMAR (BID ID -3383966)

M/S JAI PRAKASH GUPTA (BID ID -3386917)

M P TYAGI ENGINEERS AND CONTRACTORS (BID ID -3387010)

AMIT ASSOCIATES (BID ID -3387269)