SPECIAL REPAIR TO BUILDING No T 14 AND CERTAIN MINORWORKS AT MASIMPUR MIL STN UNDER GE SILCHAR

Amount

PART-I (B/R WORKS) Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge or any thickness in roof covering /wall cladding complete all as specified and directed.

Demolition of Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) n.exc 1.5 sqm each complete all as specified & directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm but n exc 4 sqm each complete all as specified.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified & directed.

Dismantling boarding any description fixed in any position with nails complete all as specified and directed.

Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards / slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

Dismantling of timber fillets rails, posts, rafters, purlins etc under 40 Sqcm in section, in any position in unframed work complete all as specified and directed.

Dismantling timber scantlings 40 sqcm and over in section, in any position, unframed work, etc complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified & directed.

Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing complete all as specified & directed

Demolition of brick/stone masonry, built in cement mortar including all quoins, arches, pillars etc but exluding ashlars facings, dressed stone work and pre-cast concrete articles complete all as specified & directed.

Surface dressing n exc 15 cm deep in soft/loose soil complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits manholes, pier holes and getting out in soft/loose soil complete all as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out in soft / loose soil , returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified and directed.

Returning filling in incl watering, ramming in layers n.exc. 25cm thick in soil complete all as specified and directed.

Removing excavated surplus soil to a distance n.exc. 50m and depositing where directed at level n.exc. 1.50m above the starting point complete all as specified and directed.

M& L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for Hardcore of broken bricks of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified & directed.

Material and labour for PCC 1:4:8 type D2 using 40 mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and directed.

Material and labour for PCC 1:3:6 type C2 using 40 mm graded stone aggregate in foundations, filling and mass concrete complete all as specified and directed.

M&L for Reinforced cement concrete Design mix (M-25) using 20 mm graded aggregate as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc., basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for Reinforced cement concrete Design mix (M-25) using 20 mm graded aggregate as in columns,pillars, piers etc, complete all as specified and directed.

M&L RCC Design mix (M-25) using 20 mm graded aggregate in beams, cantilevers, bressummers, lintels over 1.50 mtr span complete all as specified and directed.

M&L RCC Design mix (M-25) using 20 mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the likecomplete all as specified and directed.

Material and labour for Formwork to sides of foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work vertical or to batter for rough finished flat surface of concrete complete all as specified and directed.

Material and Labour for Formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished surfaces of concrete complete all as specified and directed.

Material and Labour for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished surfaces of concrete complete all as specified and directed.

Material and Labour for Formwork to sides and soffits of floor or roof beams, beam haunch ings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces of concrete complete all as specified and directed.

Material and labour for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail ings, openings in concrete walls, floor and roofs n exc 10 cm wide and sides of RCC/ PCC bands in walls, horizon tal or sloping and similar work exc 5cm but not exc. 10cm wide for rough finished flat surface of concrete, complete all as specified and directed.

Material and labour for Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizon tal or sloping and similar work exc 10cm but not exc. 20 cm wide for rough finished flat surface of concrete, complete all as specified and directed.

Material and labour for mild steel TMT bars 10mm dia and over cut to length bend to shape required including cranking bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or secruing with clips complete all as specified and directed.

All as per Item No 32 but 6mm to 8mm dia. Complete all as specified & directed.

All as per Item No 32 but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified & directed.

Material and labour precast plain cement concrete 1:2;4 type B-1 in landings, cover slabs (for man holes etc.) chullah hoods, chajjas,water troughs, mangers, shelves and similar articles with plain face incl formwork set in CM 1:4 scomplete all as specified and directed.

Material and labour brick work with sub class ‘B’ brick straight or curved on plan exc 6 mtr mean radius built in cement mortar 1:6 complete all as specified and directed.

All as per srl item No 37 above but except bricks complete all as specified and directed.

Material and labour for half brick work with sub class ‘B’ brick straight or curved on plan to any radius built in cement mortar 1:4 complete all as specified and directed.

Material and labour for 4 mm thick Asbestos cement plain building boards, fixed to timber framework with screws complete all as specified and directed.

Supply and fix second class hard wood 50 mm thick boarding clean sawn as in purlin, rafter etc fixed with nails complete all as specified and directed.

Supply and fix pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Supply and fix pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for 75 mm thick PCC 1:4:8 type D2 (using 40 mm graded stone aggregates) as in subbase of floor complete all as specified & directed.

M&L for 100 mm thick PCC 1:3:6 type C1 (using 20 mm graded stone aggregates) as in floor finished even & fair complete all as specified & directed.

M&L rendering 15 mm thick cement rendering in two layer each of 10+5 mm thick on fair faces of brick wall or concrete surfaces in CM 1:4 & water proofing compound mixed with second layer @ 3% finished even and fair complete all as specified & directed. Note -WPC shall be measured and paid separetly.

M&L rendering 15 mm thick cement rendering on fair faces of brick wall or concrete surfaces in CM 1:4 finished even and smooth without using extra cement, complete all as specified & directed.

Material and labour for 10 mm thick rendering in cement mortar 1:6 on other side of lathing surfaces finished fair and even without using extra cement complete all as specified and directed.

Material and labour for 10 mm thick rendering in cement mortar 1:3 on roof slab finished fair and even without using extra cement mixed with second layer @ 3% finished even and fair complete all as specified & directed. Note -WPC shall be measured and paid separetly.

Material and labour for 5 mm thick rendering in cement mortar 1:3 on ceiling finished fair and even without using extra cement finished even and smooth complete all as specified & directed.

Supply only WPC complete all as specified and directed.

Material and labour for plain cement concrete 1:2:4 type B-1 using 20 mm graded crushed stone aggregate in surface channel/drain complete all as specified & directed.

Material and labour for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mi- tred/stopped ends etc complete all as specified & directed.

Add or deduct for each 25 mm girth or part thereof over or under 30cm complete all as specified & directed.

M&L for 75mm thick cement concrete 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection finished even and smooth without using extra cement laid in panels and joints filled with bituminous mastic filling with 1 part of bitumen and 3 part of sand complete all as specified and directed.

S&F Rolled Mild Steel Fe 410 -W (Gde- E- 250) quality- A in Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings also fastening and fixing complete all as specified and directed.

S&F 1 mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as requirednging door fittings also fastening and fixing complete all as specified and directed.

Supply and fix Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plate using steel conforming to Fe-290 Gde E-165 complete all as specified and directed.

M & L for mild steel works as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required, clamps, holdfasts, wall ties, hooks for holding fans and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

S&F Non Skid ceramic tiles colour 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15 mm thick screed bed or bedding layers in cement mortar 1:6 including brushing with neat cement slurry with 3 Kg of cement per sqm complete all as specified and directed.

All as per Srl item No 61 above as in skirting over & including 10 mm thick screed bed or bedding layers in cement mortar 1:4 including brushing with neat cement slurry with 3 Kg of cement per sqm complete all as specified and directed.

S&F Non Skid ceramic tiles colour 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 but not exceeding 0.11 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15 mm thick screed bed or bedding layers in cement mortar 1:6 including brushing with neat cement slurry with 3 Kg of cement per sqm complete all as specified and directed.

S&F 20 mm thick Granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window-cover & including 15 mm thick screed bed or bedding layers in cement mortar 1:4 complete all as specified and directed.

M&L for coloured glazed ceramic tiles (450x300) 6mm to 7mm thick on vertical surface such as skirting, dados, risers etc. set and jointed in neat cement slurry and pointed in coloured cement or pigment to match colour tiles over & incl 10 mm thick screed layer in CM 1:4 complete all as specified and directed.

S&F Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match shade of the slab including rubbing and polishing over & including 20 mm thick screed bed or bedding layers in cement mortar 1:3 including brushing with neat cement slurry with 4 Kg of cement per sqm complete all as specified and directed.

M&L Machine cut kota stone slab 20-25mm thick as in dado / skirting over cement screed base laid and jointed with grey cement slurry mixed with pigment to match shade of the slab including rubbing and polishing over & including 10 mm thick screed bed or bedding layers in cement mortar 1:3 including brushing with neat cement slurry with 4 Kg of cement per sqm complete all as specified and directed.

M&L Plain cement concrete 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in bed blocks, coping, lintels upto 1.5m clear span, cills, lin steps, kneelers, bed plates, apex stones kerbs benching , levelling course and similar work including necessary form work complete all as specified and directed.

M&L Plain cement concrete 1:3:6 type C-0 (using 12.5 mm graded stone aggregate) as in bed blocks, holdfast blocks, coping, lintels upto 1.5m clear span, cills, lin steps, kneelers, bed plates, apex stones kerbs benching , levelling course and similar work including necessary form work complete all as specified and directed.

Supply and fix Pressed steel frames made of 1.25mm thick MS sheet of profile 125x60mm for door frames with one or more rebates including hinges (100/50mm stainless steel),lock strike plate, shock absorber, 20mm dia 60mm long MS conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified and directed.

All as per item no.70 above but of size 105x60 mm, complete all as specified and directed.

Supply and fix Framed work such as grills, gratings, etc. with ends of bars or forged into spikes, framed guard bars, barred iron doors; ladders; framed balusters, walk ways, railings, framework of water tanks and similar work con- forming to Fe 290 Gde E-165, complete all as specified and directed.

Supply and fix 35 mm thick 2nd class hard wood as in Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass,etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats supplied and fitted to chowkats complete all as specified.

Supply and fix 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sidesupplied and fitted to chowkats supplied and fitted to chowkats complete all as specified.

Supply and fix Steel windows with side hung shutters including box type hinges with steel handles, 2 Nos steel tower bolts 100mm long peg stay complete with glazing bars, dovetailed or welded, including locking arrangements complete all as specified.

All as per item no. 75 above but without glazing bars, complete all as specified and directed.

Supply and fix Steel ventilator with top hung shutter including hinges, steel peg stay, lugs as in hold fast with locking arrangements and 3mm thick plain sheet glass with oil putty complete all as specified & directed .

Supply and fix PVC door frame of size 50 mm X 47 mm made out of 5 mm thick plain colour PVC sheet reinforced with MS square tube complete all as specified & directed.

Supply and fix Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified & directed.

Supply and fix 2nd call hard wood as in small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles n exc 200 cucm each complete all as specified & directed.

S & F Second class hardwood in scantling,clean sawn, timber framed and fixed in position, complete all as specified and directed.

Material and labour for second class hard wood plain fillets, square, rectangular or triangular in section, wrought secured with nails sectional area exc. 6 sqcm but not exceeding 13 sqcm complete all as specified and directed.

Material and labour for second class hard wood plain fillets, square, rectangular or triangular in section, clean sawn secured with nails sectional area exc. 6 sqcm but not exceeding 13 sqcm complete all as specified and directed.

Supply and fix 4.00 mm thick sheet galss ordinary quality and glazing with oil putty in square not exc. 0.50 sqm in each pane, complete all as specified and directed.

Supply and fix 100mm mild stainless steel butt hinges fixed with stainless screws complete all as specified and directed.

Supply and fix 125 mm long aluminium handle cast type anodised complete all as specified & directed.

Supply and fix 200 mm long aluminum anodised barrel tower bolts of extruded section complete all as specified & directed.

Supply and fix 200 mm long aluminum anodised barrel tower bolts of extruded section complete all as specified & directed.

S&F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

Supply and fix Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.4 mm , complete all as specified and directed.

Supply and fix, Vitreous China wash basin, angle back, size 600x480mm white, excluding taps, waste, chain and plug and porcelain stopper including brackets and waste pipe complete all as specified & directed.

Supply and fix, Vitreous China wash basin, counter top size 560x461mm oval shape white, excluding taps, waste, chain and plug and porcelain stopper including brackets and waste pipe complete all as specified & directed. Make Cat aprt No 10017 of Jaquar or equivalent to Hindustan sanitary ware (hindware) / Parryware (superfine) / Cera / Somany sanitaryware

Supply and fix, as in repair, vitreous china squatting pan of Orrisa pattern size 580mm x 440 mm white with integral foot rests (excluding flushing cistern and flush pipe) including connection making good to floor complete all as specified and directed.

Supply, lay and fix 15mm bore galvanised iron water tube medium grade with all fitting and fixed to wall, ceiling or laid in floor and trench complete all as specified and directed.

Supply, lay and fix 20mm bore galvanised iron water tube medium grade with all fitting and fixed to wall, ceiling or laid in floor and trench complete all as specified and directed.

Supply, lay and fix 25mm bore galvanised iron water tube medium grade with all fitting and fixed to wall, ceiling or laid in floor and trench complete all as specified and directed.

M & L for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

M & L for Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove and making good in cement mortar 1:3 , cutting not exc 10 cm girth complete all as specified and directed.

Supply and fix,15 mm bore bib tap long body and fancy type, chromium plated, cast copper alloy with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule fixed in repairs complete all as specified and directed.

Supply and fix 15 mm bore pillar tap fancy type, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without letter Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe fixed in repairs complete all as specified and directed.

Supply and fix, angle stop valve fancy type, cast copper alloy,chromium plated ,screwed down high pressure, with crutch or butterfly handles for 15 mm bore pipe or for unions fixed in repairs complete all as specified and directed.

Supply and fix CP grating 100 mm dia complete all as specified and directed.

Supply and fix 32 mm bore waste fitting brass CP gfor sink with long screwed shanks & fly nut flkange embedded in CM & other end fixed complete all as specified and directed.

S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Supply & fix in repairs Tubular towel rail, 20mm dia, D type, 60cm long between fl anges fixed with chromium plated brass screws and wooden/plastic cleat complete all as specified and directed.

Supply and fix soap dish, chromium plated, standard quality fixed to wall with chromium plated brass screws complete all as specified and directed.

Supply and fix PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

M&L for 3 mm thick,Sheet glass,ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane, complete all as specified and directed.

Vitreous China urinals, bowl type urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed.

Supply and fix in repairs PVC valveless, syphonic action type, low level PVC flushing cistren 10 ltr cap white with flush pipe & all fitting and flush pipe complete all as specified and directed.

Supply and fix 40 mm bore PVC (SWR) Pipes single socketed, in any length with rubber ring joints,fixed to walls with suitable size of clamps , nuts bolts complete all as specified and directed.

Supply and fix 110 mm bore PVC (SWR) Pipes single socketed, in any length with rubber ring joints,laid in trenches or floor complete all as specified and directed.

Supply and fix 75 mm bore PVC (SWR) Pipes single socketed, in any length with rubber ring joints,fixed to walls complete all as specified and directed.

Supply and fix 75 mm bore PVC (SWR) Cowl complete all as specified & directed.

Supply and fix 110 mm bore PVC (SWR) junction single (single T) equal or unequal complete all as specified & directed.

Material and labour PVC (SWR) floor trap, 75mm dia outlet, plain with chromium plated grating including jointing with solvent cement complete all as specified and directed.

Supply and fix 75 mm bore PVC (SWR) bends of any radius complete all as specified & directed.

Supply and fix 110 mm bore PVC (SWR) bends of any radius complete all as specified & directed.

Supply and fix 1000 Ltr Rotaional moulded polyethylene water storage tank cylindrical vertical with closed top hoisted and fixed in position including dismantling water tank any type and any position from site of capacity 1000 liters complete all as specified and directed.

Supply and fix 20 mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Supply and fix 25 mm dia PVC Ball valves (Minimum weight of valve 210 gms) high pressure of PTMT with epoxy coated Aluminium rod and high density plastic ball screwed for iron pipe and fixed complete all as specified and directed.

Supply and fix solar cat eye aluminum alloy shall (100% water proofing design according to 65) of size 125mm x 125mm x 25mm (shank 65mm) of high efficiency Mono rystafie solar panel 2.4V/ 0.3 watt one NI-ed rechargeable battery (1.2V/ 1600MA) consisting of super bright LED with 10,000 to 18,000 mcd completed as per manufactures instructions etc. complete all as specified & directed.

Supply and fixing metal tubular dealineator made out of ABS round body fitted with 2 Nos 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and thermo plastic elastomer 3 bands of green, red and yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in PCC 1:2:4 (150x150x300mm) type B1 complete all as specified and directed

Supply and fixingTraffic covex mirror of 60 cm gia having 130 degree of viewing angle made out of polycarbonate materials brim & back holding plates made of metal / FRB alongwith pole mounted brackets and pole 50 mm dia of galvanised steel firmly fixed to the ground by means of PCC 1:2:4 type B-2 using 40 mm graded stone aggregates of size 50 cm x 50 cm x 60 cm complete all as specified and directed.

Materials and Labour for Mild steel angle, flat work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc., flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting etc. conforming to Fe -290-Gde E-165 complete all as specified and directed.

Supply only MS round or square bars 10 mm dia as in tie rod cut to length bend to shape as required for fixing of chain link fencing complete all as specified and directed.

Supply only 10 mm dia MS screw bolts (machine made ) with hexagonal or square heads at one end & screwed the other or screwed both ends, each screwed end to be fitted with washers & one hexagonal or square nut length of bolt not exceeding 5 cm long complete all as specified and directed.

Supply only Chain link fencing 4 mm dia galvanised steel wire complete all as specified and directed. Note:- Payment of line wire, bolts and nuts to be paid separately

Fixing only of chain link fencing incl. line wires any mesh and type to any of standards rails, straining bolts etc including provision of binding wire complete all as specified and directed.

Material and Labour for applying 1mm thick wall care putty on wall complete all as specified and directed.

M&L preparation of old painted steel surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L preparation of new steel surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

Material and labour for preparation of new and previously un-treated wood and wood base surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

Material and labour for preparation of old painted wood and wood base surfaces of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

Material and labour for preparation of new and previously un-treated steel surfaces of any description not exc. 10cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

Material and labour for preparation of new and previously un-treated wood and wood base surfaces of any description not exc. 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and directed.

Material and labour for preparation of old painted wood and wood base surfaces of any description not exc. 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

Material and labour for preparation of plastered or un plastered surfaces of walls and applying two coats of oil bound distemper over one coat of primer complete all as specified and directed.

M&L for complete removal of existing treatment and applying two coat of oil bound distemper (white or tinted) over one coat of chalk whiting on wall over putty to make surface even and smooth, complete all as specified and directed.

M & L for preparation of newly plastered surfaces and applying three coats of white wash on walls complete all as specified and directed

M & L for preparation of newly plastered surfaces and applying three coats of white wash on ceiling complete all as specified and directed

M & L for preparation of old decorated plastered surfaces and applying two coats of white wash on walls incl brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots complete all as specified and directed

M & L for preparation of old decorated plastered surfaces and applying two coats of white wash on ceiling incl brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots complete all as specified and directed

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified and directed.

Supply and laying APP based polymeric membrane 3 mm thick (Minimum), weighting not less than 3.5 kg/Sqm reinforced with polyester non woven fabric (weighting not less than 160 gms/sqm) shall be applied over Bituminious primer as specified above. Application of polymeric membrane shall be by torching application etc as per manufacturer's instructions. The overlaps shall be minium 100 mm on the transverse direction and 75 mm longitudinal direction including one coat of aluminium paint over the APP modified membrane @ 0.11 Kg/Sqm complete all as specified and directed.

PART-II (E/M WORKS) Taking down carefully copper/aluminum existing point wiring (light/fan/socket or power points) complete incl wooden battens/casing capping or conduit etc (without disturbing existing fittings point wiring etc) and all connected fittings such as switch, socket, ceiling rose, lamp holder, brackets ceiling fittings, bulk head fittings and fan regulator etc and making good to disturbed surfaces of wall floor etc complete all as specified and directed.

M&L for Point wiring using FRLS PVC insulated unsheathed multi strand copper conductor cable 1100 volt garde 1.5 sqmm including 1.5 Sqmm FRLSH PVC insulated unsheathed multi strand copper conductor earth wire drawn through and including PVC casing capping of suitable size with all fitting and fixture accessories on roof, wall, celling etc terminated in and incl concealed pressed steel sunken box readily available ( having wall thickness not less than 1.22 mm upto 200 x 300 mm box size & having wall thickness not less than 1.63 mm beyond 200 x 300 mm ) duly covered with 3 mm thick bakelite sheet cover for fixing switches , sockets , fan regulators etc incl testing and making good to disturbed surface to match existing surface for one light/fan/bell point complete all as specified and directed.

All as per item No. 144 above but for one 3 pin socket outlet point, 5 Amps control by one switch on independent board complete all as specified.

All as per item No. 144 above above but for one 3 pin socket outlet point, 5 Amps control by one switch on same board with other switches complete all as specified and directed.

All as per item No. 144 above above but for one 15 Amps socket point control by one switch on independent board with 2.5 Sqmm size PVC insulated unsheathed multi-stranded copper conductor cable with 2.5 sqmm PVC insulated unsheathed single core copper conductor earth wire complete all as specified and directed.

M&L for Point wiring using FRLSH PVC insulated unsheathed multi strand 1100 volts copper conductor cable 1.5 sqmm including 1.5 Sqmm FRLSH PVC insulated unsheathed multi strand copper conductor earth wire drawn through and including concealed PVC conduit of appropriate size not less than 20 mm dia and 1.8 mm thick including all fittings viz tees, bends, junctions box , connecting earth including cutting groove for concealed wiring, making good to disturbed surface of wall/floor with cement mortar and finishes to match existing including connection of cable with MCBs or bus bar shall be done through proper size copper/brass thimble of pin/u type etc for one light/fan/bell point with proper colour coding complete all as specified and directed.

All as per item No.148 above but for 5 Amps socket Point (Same board), complete all as specified and directed

All as per item No. 148 above but for 5 Amps socket Point (Independent board), complete all as specified and directed

Supply and fix Ceiling rose, 3 phase/ PVC/ polycarbonate, isolated body complete all as specified & directed.

S&F switch piano flush type 5 Amp one way complete all as specified and directed.

Supply and fix socket outlet 3/5 pin 5 Amps flush type complete all as specified and directed.

Supply and fix socket outlet 3 pin 5 Amps and 5/6 pin 15 Amps flush type complete all as specified and directed.

Supply and fix switch socket combination 2 in 1, 3 pin 5 Amp flush type complete all as specified and directed.

S & F Angular Lamp holder, PVC/ Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S & F LED bulb 10 watt, 5 star rated and connectong to lam holder complete all as specified and directed.

S&F LED linear light fittings 20 Watt having 30 min backup 9 working as regular 20 watt in normal mode and 4 watt in backup mode ) and connecting up with three core flexible copper conductor cable of suitable size from ceiling rose and connecting with 3 core flexible copper cable PVC insulated of size 16/0.20 mm etc complete all as specified and directed. Make:- Crompton Greaves Cat No. CCS-100-20-65-HL2-DP-NWH or equivalent to Bajaj/Philips/Wipro/Syska LED/ M/S Surya Roshni Limited/M/S Jaquar & Company Pvt Ltd/ Havells

S&F LED linear light fittings 20 Watt basic all purpose surface and wall mounted and LED batten with polycarbonate housing and intrigated electronic driver and connecting with 3 core flexible copper cable PVC insulated of size 16/0.20 mm etc complete all as specified and directed. Make:- Crompton Greaves Cat No. CCS-100-20-65-HL2-DP-NWH or equivalent to Bajaj/Philips/Wipro/Syska LED/ M/S Surya Roshni Limited/M/S Jaquar & Company Pvt Ltd/ Havells

Supply and fix street /bldg security light LED luminaire 25 watt IP 66 LED lamp, driver etc, including wall bracket 1.5 mtr long made out of 40 mm bore GI light grade pipe with suitable siz of clamps nuts bolts & all accessories & making connection with FRLS PVC insulated unsheathed multi strand copper conductor cable 1100 volt garde complete all as specified and directed. Make: Crompton Cat No. LSTS-25-CDL/NL-M or equivalent to Bajaj/Philips/Wipro/Syska LED/ M/S Surya Roshni Limited/M/S Jaquar & Company Pvt Ltd/Havells

Supply and fix MS body exhaust fan, AC single phase, 240 V of size 300 mm sweep with louvers including necessary connection and replacement of flexible copper cable from ceiling rose and taking down of old unserviceable fan complete all as specified and as directed. Make :-Crompton Cat Part No DRIFT AIR PLUS ANTI DUST or equivalent in Havells / Bajaj / Orient

Supply and fix plastic body exhaust fan, AC single phase, 240 V of size 300 mm sweep with louvers including necessary connection and replacement of flexible copper cable from ceiling rose and taking down of old unserviceable fan complete all as specified and as directed. Make :-Crompton Cat Part No BRISK AIR NEO or equivalent in Havells / Bajaj / Orient

Supply and fix BLDC 5 star rating ceiling fan, AC single phase, 240 V of size 1200 mm sweep including necessary connection and replacement of flexible copper cable from ceiling rose and taking down of old unserviceable fan complete all as specified and as directed. Make :-Crompton Cat Part No SUPER BRIZ DECO or equivalent in Havells / Bajaj / Orient

Dismantling of unserviceable LT cable of any size and removing from site for taking in credit, complete all as specified and directed.

Taking down carefully sub main wiring including all accessories without disturbing existing wiring fittings fixtures etc and amking good to the disturbed surfaces , complete all as specified and directed.

M & L for circuit /submain wiring along with earth wire 2 x 4 Sqmm PVC FRLSH insulated unsheathed cable multi-strand copper conductor including 1 x 4 Sqmm PVC insulated unsheathed multi strand copper conductor earth wire through and including PVC casing capping of suitable size with all fitting and fixture accessories, connecting earth including cutting groove for concealed wiring, making good to disturbed surface of wall/floor with cement mortar and finishes to match existing incl taking down old unserviceable submain wiring complete all as specified and directed. Note: Two run of single core cable and one run of earth wire will be mearsured as one length

Supply and fix sheet metal enclosure powder coated single phase DB for fixing of MCBs, 8 ways double door with bus bar including grouting on the wall by means of screws and rawal plugs and making good disturbed surfaces including taking out of existing unserviceable DB complete all as specified and directed.

Supply and fix sheet metal enclosure powder coated single phase DB for fixing of MCBs, 4 ways double door with bus bar including grouting on the wall by means of screws and rawal plugs and making good disturbed surfaces including taking out of existing unserviceable DB complete all as specified and directed.

Supply and fix MCB SP of capacity 6-32 Amps, 240v, 10KA 'C' curve, complete all as specified & directed.

Supply and fix MCB SPN of capacity 40 Amps, 240v, 10KA 'C' curve, complete all as specified & directed.

Material and labour for laying of bricks locally available sub-class 'B' brick (old size) for cable protection cover laid flat and dry in trenches over the cable perpendicular to the directon of cable complete all as specified and directed.

Supply and spread sand in trenches as sand cushioning to under ground cable for protection with fine river sand and provide reqd cover after punning down complete all as specified and directed. Note : Thickness of sand cushion after punning down will be measured and paid.

Material & labour GI tube light grade 40 mm for protection of UG cable including dismantling of old unsv pipe complete all as specified and directed.

M&L for 100 mm thick PCC 1:3:6 type C1 (using 20 mm graded stone aggregates) as in floor finished even & fair complete all as specified & directed.

S&F Cutting existing steel tubing 25mm bore for inserting Tee etc for taking 25mm bore branch pipe including fittings ,complete all as specified and directed.( the rate inclusive of GI Tee)

Supply and fix 25 mm dia Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Supply and fix 25 mm bore brass ball valve high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

Supply, fixing, commioning & testing of XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, Electric power cable (heavy duty) with aluminium conductors, 1100 volts, grade cross sectional area 10Sqmm 2 core laid in trenches/fixed to wall/under road/pipe etc with and including copper cable glands & copper thimbles complete all as specified and directed.

Supply, fixing, commioning & testing of XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, Electric power cable (heavy duty) with aluminium conductors, 1100 volts, grade cross sectional area 35 Sqmm 3.5 core laid in trenches/fixed to wall/under road/pipe etc with and including copper cable glands & copper thimbles complete all as specified and directed.

Material and labour for earthing with galvanised steel earth plate electrode 60cmX60cmX 6mm thick burried directly in ground (earth pit not less than 2.25 mtr below ground level) with top edge of the plate not less than 1.5 mtr below ground level connected to earth wire 4 mm dia GI wire with mild steel nuts bolts checknuts & washers and connected to equipment as directed incl funnel with Gi medium grade watering pipe 20 mm bore , wire mesh , charcoal or coke and commn salt in alternate layers of 15 cm compacted thickness all around the earth electrode with concrete pit in PCC 1:3:6 type C-1 with 50 mm thick precast RCC cover in PCC 1:2:4 type B-1 cover slab reinforced with 8 mm dia deformed bars @ 15 cm c/c with suitable handle of 10 mm dia round bar , 15 mm bore medium grade pipe for earth lead protection incl necessary excavation and earth wok in soft / loose soil and disposal of spoil to a distance n exc 50 m and necessary testing complete all as shown in electrical plate No 3 of MES SSR Part-I complete all as specified and directed.

MAGADH TRADING

m/s builders and suppliers

M/S LUIT CONSTRUCTION

M/S SUBHAM ENTERPRISE

M/S TAPAN KUMAR RAY

M/S R A ENTERPRISE

MS AFTAB LASKAR