ADDN / ALTN OF EXISTING SECURITY WALL ADJOINING CIVIL AREA AND RAILWAY TRACK AT MIL STN KOTA

Amount

Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth; for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, etc not exceeding 10sq m on plan and not exceeding 1.5m in depth and getting out in soft/loose soil complete all as directed

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering complete all as specified & directed

Removing excavated material (soil) n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point etc, complete all as specified and directed

M&L PCC (1:4:8) type D.2 using 40mm graded stone aggregate as in foundation, filling and mass concrete etc, complete all as specified and directed

M&L RCC M-25 (Design mix) using 20 mm graded stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete etc, complete all as specified and directed

M&L Reinforced cement concrete M-25 (design mix) using 20 mm graded stone aggregate as in beams cantilevers, bressummers, lintels over 1.5m span etc, complete all as specified and directed

M&L Reinforced cement concreteM-25 (design mix) using 20 mm graded stone aggregate as in Columns, pillars, piers, posts and struts etc, complete all as specified and directed.

M&L for Brick work in CM (1:6) using sub class B bricks straight or curved on plan exceeding 6 meter mean radius all as specified and as directed.

M&L for formwork to flat rough finished surface of sides of concrete foundations, footings, bases of columns, raft and raft beams sides and soffits (if any) of foundation and plinth beams and similar work; vertical or to batter for flat rough finished surface of concrete etc, complete all as specified and directed.

M&L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exceeding 10cm but not exceeding 20cm wide etc, complete all as specified and directed

Use & waste of form work to sides of pillars, posts, struts, piers, column and stanchion rough finished square, rectangular surface etc, complete all as specified and directed.

M&L for Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

M&L for mild steel TMT steel bars 5mm dia and over up to and including 10mm dia in stirrups, spacers etc, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed) not less than 0.9mm dia or securing with clips etc, complete all as specified and directed.

M&L rendering 10mm thick in CM (1:6) and 5mm thick in CM (1:4) on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement and using water proofing compound etc complete all as specified and as directed

M&L for preparation of newly plastered or un-plastered wall surface and applying two coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489 : 2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (company Depot tinted) with silicon additives @ 1.43 litre / 10 sqm over and including priming coat of exterior primer applied @0.90 litre / 10 sqm etc, complete all as specified and directed.

S&F mild steel sections as in wind tie, hand rails, roof securing bolt, fixing wire mesh frame including drilling holes, notching for wire mesh etc fat iron fillet for securing wire mesh including necessary bolting, riveting etc and similar work confirming to Fe-410 or Fe 310-0 etc complete all as specified and directed.

M&L for Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) etc complete all as specified and directed.

S&F concertina coil made of superior ultra barb (a razor bound sharp concertina loop) galvanised having 60+1 cm dia including securing tying at crossing with and provision of galvanised mild steel wire staples or steel pins, (minimum weight of concertina coil per meter shall not be less than 1.42 Kgs and having 50 nos. round per 6Mtr length) etc complete all as specified and directed.

S & F PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors dia of pipe 100 mm etc, complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and as directed

Demolition of cement concrete (reinforced) in roofs, floors (other than ground floor), beams, staircases, landing, chajjas etc and remove the same outside of MD land distance 1.5km to 5km etc complete all as specified and directed.

Demolition of brickwork or stone/ boulder masonry, built in lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles and remove the same outside of MD land etc, complete all as specified and directed.

M&L for Dismantling wrought iron or mild steel work in any position not otherwise provided for etc, complete all as specified and directed

M&L for random rubble masonry un-courses well bonded bedded and solidly hearted built in CM (1:6) etc, complete all as specified and directed.

M&L for preparing steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer etc, complete all as specified and directed.

M&L rendering 15mm thick in CM (1:4) on stone surface and finished even and smooth without using extra cement and using water proofing compound etc complete all as specified and as directed (Note : water proofing compound shall be measured and paid separetly)

M&L for PCC (1:2:4) type B-1 using 20mm graded stone aggregates as in coping apex stone, bed plates parapets, cills slightly rounded or chamfered angles and throatings etc, complete all as specified and directed.

Supply only liquid water proofing compound

Schedule of Credit

L P Singh and Co.

SINGH ENTERPRISES