Repair to flooring, joinery, sanitary fittings etc and internal water supply to certain buildings of Offrs md accn area (RA Lines) at Kannur under AGE (I) Cannanore.

Amount

Dismantling single layer Mangalore pattern tiles in roofing including tilting tiles all as specified and directed.

Dismantling of battens for tiles, shingles etc of any size including tilting fillets all as specified and directed.

Dismantling timber scantling 40 sqcm and over in section in any position unframed work all as specified and directed.

M&L for structural steel work in rectangular or square tubular section as in purlin/battens including special shaped washer, Fe-410-W (Gde E-250) quality B, complete all as specified and directed.

S&F Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions as directed.

S&F Pre- painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, ridges, valley gutter fixed with self tapping screws as per manufacturers instructions as directed.

M&L for preparation of new or old untreated steel surfaces of any description not other wise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified & directed.

Demolition of stone slab and tiles of any description and thickness in floors including cement mortar bedding (but not backing), and rubbish off the premises outside MD land and all as directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) and removing debris outside MD land all as directed.

M&L for coloured joint free non-skid ceramic tiles, 8mm to 10mm thick, area of each tile exceeding 0.18 Sqm but not exceeding 0.36 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 15mm thick screed bed or bedding layer in cement mortar (1:4) all as specified and directed.

M&L for coloured glazed tiles, 7mm to 8mm thick, area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, as in skirting / dado, set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 10 mm thick backing on stone/brick masonry surfaces in cement mortar (1:4) all as specified and directed.

Taking down chowkats with shutters n exc. 1.5 Sqm each (without taking off shutters from the frame) all as directed.

Taking down chowkats with shutters exc. 1.5 Sqm but n.exc 4 Sqm each (without taking off shutters from the frame) all as directed.

Taking down wooden door shutters of any description n exc 1 Sqm each all as directed.

Taking down wooden door shutters of any description exceeding 1 Sqm and not exceeding 2 Sqm each all as directed.

M&L for second class hardwood, plain, solid straight chowkats & frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints all as specified and directed.

All as per item No 16 here in before but for with transoms and mullions, with double rebated on the solid frame for fixing double shutters all as specified and directed.

S&F 4mm thick plain sheet glass, ordinary quality and glazing with oil putty in squares not exc 0.50 Sqm in each pane all as specified and directed.

M&L solid PVC door frame of sizes 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, all as specified and directed.

S&F factory made solid PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain coloured PVC “C” channel having a PVC sheet strip of 20mm width stock inside with solvent cement for stiles and plain colour PVC sheet for top rails, lock rails and bottom rails on either side and as gap insert for top rail & bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour of PVC sheet fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement etc. Details as peer specification and drawings and all as directed.

M&L for second class hardwood panelled shutter 30mm thick (two panesl) with lock rail and panel of 9mm BWP, commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), all as specified and directed.

S&F 30mm thick second class hardwood glazed and skelton shutters, open rebated and prepared to receive glass, gauze, etc; (with out sash bars), edges of framing, fitted with cut and mitered beads for securing glass, etc sizes of members of shutters as specified in SSR Part-I, Section 8, Clause 8.24 (a) all as specified and directed.

S&F 30mm thick second class hardwood glazed and skeleton shutters, open rebated, edges of framing plain, chamfered or rounded, fitted with cut and mitred and rebated sash bars, divided into squares, for securing glass gauze, etc; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.20(b) all as specified and directed.

S&F stainless steel butt hinges medium weight; 100mm size all as specified.

S&F stainless steel butt hinges medium weight; 75mm size all as specified.

S&F 100mm long aluminum anodized barrel tower bolts of extruded section all as specified.

S&F 150mm long aluminum anodized barrel tower bolts of extruded section all as specified.

S&F extruded aluminum alloy anodized handle fabricated type 100mm size all as specified.

S&F extruded aluminum alloy anodized handle fabricated type 150mm size all as specified.

S&F aluminium anodised sliding door bolts 300mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed

S&F in repairs aluminium anodised sliding door bolts 300mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed

M&L for mild steel flat iron of size 25 x 3mm for holdfasts for securing new wooden frames and similar articles conforming to Fe-290 Gde-E-165 all as specified and directed.

M&L for PCC 1:2:4, type C1 using 20mm graded stone aggregate for fixing hold fast including necessary form works all as specified and directed.

S&F for second class hard wood, plain fillets, square, rectangular or triangular in section, clean sawn, sectional area exc.6 & n. exc. 13 sqcm secured with nails or brads all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and directed.

S&F in repairs stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified and directed.

Supply and Fix in repairs Netlon ( Good quality ) for fly proofing (Necessary beading will be measured in the appropriate item ) as specified and directed.

Demolition of brick or stone / boulder masonry built in cement or cement lime mortar, including all quoins, arches, pillars etc. but excluding ashlar facings, dressed stone work and pre cast concrete articles and removing debris outside MD land all as directed.

M&L for laterite stone masonry, regular coursed, well bonded and solidly hearted , built in CM (1:6) all as specified and directed.

All as per item No 39 here in before but except laterite all as specified and directed. Note : Serviceable laterite stone obtained from item No 38 shall be reused.

Taking down cement or cement lime plaster on brick/stone walls or in ceiling surfaces incl racking out joints hacking for key scrubbing down with water etc and removing rubbish outside MD land all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:6) on stone masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L for rendering 15mm thick in cement mortar (1:4) on stone masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L for preparation of new plastered surfaces and applying 3 coat of white wash on walls surfaces all as specified and directed.

M&L for preparation of new plastered surfaces and applying 2 coat of cement base paint over a coat of primer on walls surfaces all as specified and directed.

M & L for 100 mm thick plain cement concrete 1:4:8, type D2 using 40mm graded aggregate as in sub floors, sub bases etc complete all as specified and directed

M&L 40mm thick PCC 1:2:4, Type B1 (using 20mm graded stone aggregate) as in flooring and finished even and smooth without using extra cement all as specified and directed.

Taking up or down steel tubing and connecting including cleaning for removing to store of sizes upto 20mm bore all as directed.

S&F for 15 mm bore UPVC pipes (ASTM) of pressure rating 10 kgf / cm2, fixed complete to walls, ceilings etc. all as specified and directed.

S&F for 20 mm bore UPVC pipes (ASTM) of pressure rating 10 kgf / cm2, fixed complete to walls, ceilings etc. all as specified and directed.

S&F 15 mm bore bib taps, cast copper alloy, chromium plated, screwed for iron pipe or for PVC pipe or for brass ferrule, fixed as in repairs all as specified and directed.

S&F in repairs 15mm pillar taps cast copper alloy with capstan heads, chromium plated, screwed down high pressure ,with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed all as specified and directed.

S&F stop cock 15mm bore cast copper alloy, chromium plated, screwed both ends for iron pipe or for unions and screwed down, high pressure with long shank & cup fixed in repair complete all as specified and directed

S&F 500 litres capacity rotational moulded polthylene water storage tanks(cylindrical vertical with closed top) of make Sintex/Polycon/Plasto hoisted and fixed in position including taking down unserviceable water tank all as specified in SSR Part I,2009 and directed.

S&F 1000 litres capacity rotational moulded polthylene water storage tanks(cylindrical vertical with closed top) of make Sintex/Polycon/Plasto hoisted and fixed in position including taking down unserviceable water tank all as specified in SSR Part I,2009 and directed.

S&F in repairs Vitreous China Wash down water closet pan (Pedestal pattern) white, (excluding flushing cistern and flush type) pedestal pan and trap including connection to drain (or outgoing pipe) and to flushing pipe, anti syphonage pipe, etc complete including plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminized hinging device all as specified and directed.

S&F in repair for PVC valveless, syphonic action type flushing cistern low level, 10 Litre capacity, white, with inlet, ball valve, float and handle including flush pipe all as specified and directed.

Supply and fix in repairs PVC connection 60cm long with PTMT nuts for flush tank, wash basin, etc. all as specified and directed

S&F in repairs 32mm Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed all as specified and directed.

S&F in repairs Health faucet (ABS body) , chromium plated suitable for 15mm dia, 1.25m long flexible tube and ABS wall hook with suitable fixing arrangements all as complete all as specified and directed.

S&F in repairs readymade PVC / bakelite toilet cabinet with openable shutter with mirror on front face (Size not less than 350x450mm) all as specified and directed.

S&F in repairs stainless steel plate rack (for kitchen), 1mm thick of overall size not less than 90cm x 90cm x 20cm of standard pattern/ design and weight not less than 6.50 Kg each all as specified and directed.

S&F in repairs angle cock 15mm bore cast copper alloy, chromium plated, fancy type complete all as specified and directed

S&F in repairs PVC lid or cover for PVC OH water tank suitable upto 1000 litre capacity of Sintex or Polycon complete all as specified and directed

Cleaning of blockage of WC Indian or European type by removing sludge and sediments getting out including cleaning and rodding of sewage pipe upto first manholes and flushing with water after cleaning, removing and depositing sludge in a pit n exc 50m from the WC as including necessary excavation in hard / dense soil , refill and disposal of surplus soil etc complete all as directed.

S&F in repairs peg set of five of metal body, chromium plated, with PVC coated hooks, first quality complete all as specified and directed

S&F in repairs ball brass valves, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe or brass ferrule of 15mm bore dia all as specified and directed.

S&F in repairs ball brass valves, high pressure, with polyethylene float and fly nut complete, screwed for iron pipe or brass ferrule of 25mm bore dia all as specified and directed.

S&F in repairs Soap dish, chromium plated, fancy type fixed to wall with wooden plugs with chromium plated brass screws all as specified and directed.

S&F in repairs flush pipe of polythelene of low or high density PVC 32mm dia suitable for flushing cistern low level, 10 Litre capacity, all as specified and directed.

S&F in repairs tubular towel rail brass, chromium plated, D type, 60cm long between flanges fixed to wall with wooden plugs with chromium plated brass screws all as specified and directed.

S&F in repairs PTMT 32mm Waste fittings, any colour weighing not less than 45gm per each suitable for sinks, basins, etc. with long screwed shanks and fly-nuts, flange end all as specified and directed.

Cleaning of terrace/loft water storage tank (inside surface area) upto 2000 litre capacity at any heights with coconut brushes, duster etc., removal of silt, rubbish from the tank and cleaning the tank with fresh water disinfecting with bleaching powder @ 0.5gm per litre capacity of tank including marking the date of cleaning on the side of tank body with the help of stencil and paint and disposing of malba outside MD land all complete as per direction of Engineer-in-Charge. Note: 1. The old date already written on tank should be removed with paint remover or black paint. 2. During cleaning if any GI fittings or ball cock tobe damaged shall be repaired by contractor at his own cost and nothing extra will be paid on this account.

S&F in repairs White plastic seat cover, solid type lid with C.P. brass hinges and rubber buffers complete all as directed by Engineer-in-Charge.

M&L for renewing glazed or non skid ceramic tiles in patches, area n exc 5 sq.m. including removing and cleaning old tiles, preparing beds and laying or setting, jointing and pointing new or old tiles complete

Providing and laying water proofing treatment in sunken portion of WCs / bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying the following treatment all as directed. (a) Preparation of surface by cleaning, treatment with sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. (b) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (c) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of of applying the following treatment all as directed.: (a) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (b) IInd course of 20 mm thick cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (c) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (d) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

Dismantling of cast iron or RCC drain pipes upto 100mm bore, jointed in cement mortar and taking out of trenches or wall all as directed.

M&L PVC (SWR) pipe type 'B' 75mm bore single socketed with solvent cement joints laid in trenches or in floors all as specified and directed.

M&L PVC (SWR) pipe type 'B' 110mm bore single socketed with solvent cement joints laid in trenches or in floors all as specified and directed.

M&L PVC (SWR) pipe type 'B' 75mm bore single socketed with solvent cement joints fixed to wall all as specified and directed.

M&L PVC (SWR) pipe type 'B' 110mm bore single socketed with solvent cement joints fixed to wall all as specified and directed.

S&F 110mm bore, PVC (SWR) P trap all as specified and directed

S&F 110mm bore, PVC (SWR) S trap all as specified and directed

S&F 75 mm bore, PVC (SWR) bend with access door any radius all as specified and directed

S&F 110 mm bore, PVC (SWR) bend with access door any radius all as specified and directed

Taking down door shutters of any description not exceeding 1 Sqm and not exceeding 2 Sqm each and refixing the same opening after easing and adjusting and refixing/renewal of builders hardware with screws all as directed.

Taking down door shutters of any description exceeding 1 Sqm each and refixing the same opening after easing and adjusting and refixing/renewal of builders hardware with screws all as directed.

Hacking out old broken glass (any thickness, size, quality or description) n exc 1.5 sqm from wooden frames including beads all as directed.

Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer-in-Charge.

RS ENTERPRISES