Repair to leakage, seepage, joinery, flooring, ceiling, sanitary fittings, plastering, painting, approach path, drain and internal electrification and repair/replacement of sewage line, connected work, hard standing, drain path and other misc works o

Amount

M&L for brick work with subclass 'B' bricks, straight or curved on plan exc 6 m mean radius built in cement mortar (1:6) (using old size bricks) including demolition of old brick in any mortar complete all as specified and directed.

All as per serial item No. 2.00 here in above but except bricks including demolition of old bricks in any mortar (Bricks obtained from dismantling shall be reused)

M&L for brick work with subclass 'B' bricks, straight or curved on plan to any radius built in cement mortar (1:4) as in half brick thick wall (using old size bricks) including demolition of old brick in any mortar complete all as specified and directed.

Taking down cement plaster on brick or stone wall etc. including racking out joints, hacking for key and scrubbing down with water etc. complete all as specified

M&L rendering 15m thick on fair faces of brick work in CM 1:4 in two layers (1st layer 10-12mm + 2nd layer 3-5mm) and finished surfaces even and smooth without using extra cement (mixed with water proofing compound where ordered) complete all as specified and directed by Engr-in-charge (Note : WPC measured and paid saperately)

M&L rendering 15m thick on fair faces of brick work in CM 1:6 in two layers (1st layer 10-12mm + 2nd layer 3-5mm) and finished surfaces even and smooth without using extra cement (mixed with water proofing compound where ordered) complete all as specified and directed by Engr-in-charge (Note : WPC measured and paid saperately)

M&L for applying wall putty 2 to 3 mm thick and rubbing with sand paper on plastered surfaces of walls after preparation of surfaces complete all as specified and directed

M&L for preparation of wall and applying exterior grade wall care putty 2 to 3mm thick to make the surface smooth as specified and directed by Engr-in-Charge.

M&L for preparation of old decorative surface of wall (plastered) by brooming down with colour brush and hand held electrical grinder, scraping down smoke soot, moulds, moss and efflorecent salts and trading oil and greasy spots and finally cleaned with sand paper all as directed by Engr-in-charge

Complete removal of existing treatment of wall upto the plastered surface of wall by brooming down with steel wire brush and hand held electrical grinder, scraping down smoke soot, moulds, moss and efflorecent salts and trading oil and greasy spots and finally cleaned with sand paper all as directed by Engr-in-charge

M&L preparation of old decorated surfaces of ceiling (Plastered) by brooming down or sand paper, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots all as directed by Engr-in-charge.

M&L for applying one coat of oil bound distemper on old decorated already prepared surfaces of walls complete all as specified and directed by Engr-in-charge.

M&L for preparation of new plastered / POP / Putty surfaces of walls and applying two coats of distemper oil emulsion over a coat of primer complete all as specified and directed by Engr-in-charge

M&L for preparation of new plastered / POP / Putty surfaces of walls and applying two coats of cement base paint over a coat of primer complete all as specified and directed by Engr-in-charge

M&L for applying one coat of cement base paint on old decorated already prepared surfaces of walls complete all as specified and directed by Engr-in-charge.

M&L for preparation of new plastered / POP / Putty surfaces of walls and applying two coats of exterior grade 1st quality weather proof paint over a coat of alkali resistant priming paint complete all as specified and directed. Make: Berger XP advance, Asian paints (Apex ultima), Nerolac (Excel total).

M&L for applying one coat of exterior grade 1st quality weather proof paint on old decorated already prepared surfaces of walls complete all as specified and directed by Engr-in-charge. Make : Berger XP advance, Asian Paints (Apex Ultima), Nerolac (Excel total)

Preparation of old AC sheets surfaces by brooming down with steel wires brushing and washing with water and applying one coat of exterior weather proof paint, complete all as specified in SSR part Iand directed by Engr-in-Charge.

M & L preparation of old painted surfaces of wood & wood based material of any description over 10 cm width or girth and applying one coat of PU Paint complete.

M & L preparation of old steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as speciied and directed.

Cutting around the pipe 75/100mm bore waste / soil pipe including taking out plant roots up to any depth in brick masonary and rejointing in pipe joint in epoxy mortar (Asian/Berger) and making good to existing surface all as directed by Engr-in-charge. (After the jointing pipe one week to be open for checking of leaking including scaffolding)

Removing / cutting trees vegetation, digging out roots from concrete or brick wall, filling holes on building (Block of 4 qtrs) wall / roof / chajja etc applying and making good with epoxy mortar (Asian/Berger) and applying surface treatment to match with existing specifications complete.

M&L rendering in patches (nexc 3.0 Sqm) 15m thick on fair faces of brick work in CM 1:4 and finished surfaces even and smooth without using extra cement (mixed with water proofing compound where ordered) complete all as specified and directed by Engr-in-charge (Note : WPC measured and paid saperately)

M & L rendering 15mm thick in patches n exc 3 Sqm in cement mortar 1:3 on fair faces of concrete surfaces, chajja/ facia finished even and smooth without using extra cement (mixed with water proofing compound where ordered) complete all as specified and directed by Engr-in-charge. (Note : WPC measured and paid saperately)

Extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work exc 15 cm but n exc 30 cm in width or girth; including cutting to edges, all mitres and stopped ends, etc.

M&L for applying one coat of white wash on old decorated already prepared surfaces of walls complete all as specified and directed by Engr-in-charge.

M&L for applying one coat of white wash on old decorated already prepared surfaces of ceiling complete all as specified and directed by Engr-in-charge.

M & L 10 mm thick rendering in cement mortar 1:3 on concrete surfaces as in ceiling, surface finished fair and even complete all as specified and directed.

M&L for preparation of new plastered / POP / Putty surfaces of ceilings and applying three coats of white wash complete all as specified and directed by Engr-in-charge

Demolition of cement concrete in ground floor and paving nexc 15cm thick (below or above ground level ) and removing rubbish off the MD land complete all as specified.

M&L non skid mat finish ceramic colour tiles of size 300x300 mm x 6-7 mm thick, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar (1:6) including dimantling of existing tiles complete all as specified and directed.

M&L non skid mat finish designer coloured joint free ceramic tiles of size not less than 400x400 mm x 6-7 mm thick, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in cement mortar (1:6) including dismantling of existing floor tiling complete all as specified and directed.

All as per item No 32.00 here in above but as in skirting including 10 mm thick rendering in cement mortar (1:4) including dimantling of existing tiles complete all as specified and directed.

M & L for Glazed ceramic coloured tiles of size 375X250 mm X 6- 7 mm thick or 450X350 mm X 7 mm thick on vertical surfaces such as skirting, dados and rises to steps etc. set and jointed in neat cement slurry and pointed in white cement mixed with colour cement to match the surface including 10 mm thick rendering in CM (1:4) including dimantling of existing tiles complete all as specified and directed.

M&L for PCC (1:2:4) type B-0 (usng 12.5 mm graded stone aggregate) as in leveling course to floors complete all as specified and directed.

M & L for PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in benching to drain, holdfast, padding to roof/chhajja, coping, bed block etc. and the like edge slightly rounded or chamfered including necessary use and waste of form work complete all as specified and directed..

M & L for 75mm thk PCC 1:3:6 type C-2 as in plinth protection, finished even and fair without using extra cement. The plinth protection shall be laid in alternate bays nexe 2 sqm with 10mm wide joints filled with bitumen mastic comprising of 1 part of hot bitumen 85/25 grade and 3 parts sand all by weight complete all as specified and directed.

M & L for PCC (1:4:8) type D-2 (using 40mm graded stone aggregate) as in foundation filling, mass concrete, sub base or leveling course of floor etc. complete all as specified and directed.

M&L for 18-20 mm thick machine cut polished granite 1st quality "black" stone slab over kitchen platform and similar places over and including 15mm thick screed bed in cement mortar (1:4) laid and jointed with grey cement slurry mixed with pigment to match with existing surface, rounding off exposed edges including dimantling of existing tiles complete all as specified and as directed.

M&L for coloured prepolished rubber moulded chequred cement concrete tiles 30cmx30cmx20-22 mm thick, set, jointed and pointed in neat cement slurry as in floor with grey cement and pigment over and including 20 mm thick screed bed in cement mortar (1:6) complete including dimantling of existing tiles all as specified and directed.

Taking down, resecuring/repair of wooden shutters of any description exc 1 sqm but n exc 2.0 sqm each and refixing in same opening including painting to match existing surface complete all as specified and directed by Engr-in-charge

Taking down shutters of any description not exc. 1 Sqm each and removing from site complete all as specified and directed.

All as per item No 42.00 here in above but exc 1 Sqm but n. exc 2 Sqm each complete all as specified and directed.

Taking down Chowkats with shutter (without taking off shutters) area not exceeding 1.5 Sqm each and removing from site complete all as specified and directed.

Taking down Chowkats with shutter (without taking off shutters) area exceeding 1.5 Sqm but not exceeding 4 Sqm each and removing from site complete all as specified and directed.

M&L for second class hard wood, plain, solid, straight chowkats & frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed by Engr-in-charge

S & F 35mm thick second class hardwood glazed and Skelton factory made door shutters, open rebated and prepared to receive glass/gauze etc divided into squares with plain, chamfered or rounded mitered and rebated sash bars, edges of framing plain, chamfered, fitting with cut and rebated beads for securing glass/ gauge complete all as specified in SSR Pt I-2009 section 8 clause 8.24 (a) and as directed.

S&F factory made 100 % solid wood plastic composite (WPC) door frame 125 x 63 mm made from wood plastic composite (single extruded process) material with density 780 Kg/Cum from ISO certified company door should be water proof, termite proof, fire retardant and having good screw holding capacity all as per specification and drawing as directed by Engineer-in-Charge Make : ECHON/Kumar Tech/Sintex

S&F 30 mm thick moulded WPC factory made 100% solid door (conforming as per IS-4020) made from 100% lead free single extruded with 2, 4 or 6 raised panel design on the front side with 10 mm deep mould on single side with wood grain texture and back side palin with density not less than 600 Kg/cum. Manufactured by an ISO : 9001-2015 certified company. The door should be water proof, termite proof, fire etardant and having screw holding capacity complete all as specified. Make : ECHON/Kumar Tech/Sintex

S&F factory made 100% solid wood plastic composite (WPC) door frame of size 75 mm x 50 mm x 50 mm made from wood plastic composite (single extruded process) material with density 780 Kg/Cum from ISO certified company door should be water proof termite proof fire retardant and having good screw holding capacity all as specification and drawing complete all as specified and directed by Engr-in-Charge. Make : ECHON/Kumar Tech/Sintex

M&L for 30 mm thick, factory made BWR flush shutters, solid core construction, with block board core and plywood face pannels commercial type on both sides including provision of suitable blocks for taking mortice locks, latches or other fittings complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

S&F rolled mild sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc. and fixing conforming to Fe-410-W (Gde-E-250) quality A complete all as specified and directed.

S&F in repair Factory made Steel windows with side hung shutters with box type hinges including steel handle, steel peg stay complete with glazing bars, dovetailed or welded complete all as specified and directed by Engr-in-charge

S&F in repair Factory made Steel windows with side hung shutters with box type hinges including steel handle, steel peg stay complete without glazing bars, dovetailed or welded complete all as specified and directed by Engr-in-charge

Taking down existing projected type hings from the steel window carefully with disturbing frame and fix 50 mm long mild steel box type hinge weld to steel frame and shutter with welding and making good including touch with paint and with existing surfaces including scaffolding all as directed by Engr-in-charge.

S&F powder coated aluminium ventilator fixed type half glazed and half gauged with and including hardware fittings, glazing, wire gauge, rubber packing, aluminium beading etc. as specified below including taking down old window/ventilator and making good of wall surface to match with existing surface complete all as specified and directed : - Frame : 44.5 x 44.5 mm x 1.80 mm thick Middle rail : 44.5 x 44.5 mm x 1.80 mm thick Glazing: 5 mm thick frosted glass fixed with rubber gasket and aluminium beading. Wire gauge : stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4 mm fixed with aluminium beading.

S&F powder coated aluminium grill with frame fixed to by means stainless steel screws complete all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with tinned tacks or stainless steel wire staples all as directed by Engeer-in-charge.

S&F in repair stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with tinned tacks or stainless steel wire staples all as directed by Engeer-in-charge.

S&F in repair 4 mm thick sheet glass ordinary quality and glazing with silicon and oil putty or wooden beads in square area n. exc. 0.5 Sqm in each pane all as directed by Engeer-in-charge.

S&F in repair mild steel framed work as in grill, grating etc framed guard bars, barred iron doors, ladders, frame balusters, walk ways, railing. framed work of water tanks and similar works confirming to Fe 290 Gde E165 complete all as specified and directed.

S&F in repair 18 mm thick PVC ply one side prelaminated and other side plain white colour as in cup board shutters and shelves complete all as specified and directed by the Engineer-in-Charge. Make:-Rajshree, Polyline, ECHON/Kumar Tech

S&F in repair 12 mm thick PVC ply one side prelaminated and other side plain white colour as in kitchen cabinet partition shelf, shutter, drawer, front shutters fixed with screws, solvent cement / adhesive complete all specified and directed by the Engineer-in-charge. Make:-Rajshree, Polyline, ECHON/Kumar Tech

S&F in repairs 6 mm thick PVC ply one side prelaminated and other side plain white colour as in kitchen cabinet partition shelf, shutter, drawer, front shutters, fixed with screws, solvent cement / adhesive complete all specified and directed by the Engineer-in-charge. Make:-Rajshree, Polyline, ECHON/Kumar Tech

S&F auto closing hinges 35 mm of 0 crank or 8 crank openable at 110 degree for kitchen cabinet shutters complete all as specified and directed. Make :Hexa, Shreeji, Hafele

S&F telescopic ball bearing runners 45 mm size, 500 mm long full extension load capacity 50 kgs, complete all as specified and directed. Make :Hexa/ Shreeji/ Hafele

S&F continious (Piano) hinges, mild steel, bright finish or electrogalvanised. 30 mm width of flaps (when open) complete all as specified as directed.

S&F Hasp and staple 100mm safety type, stainless steel 304 grade with hinge pin including bolt to hinge plate and fixed with screws complete all as specified as directed.

S&F 100 mm size stainless steel butt hinges and fixed with stainless steel screws, complete all as specified and directed by Engr-in-Charge.

S&F 200 mm long, solid in one piece stainless steel barrel tower bolts of extruded section 10mm dia shoot complete all as specified and directed by Engr-in-charge.

S&F 150 mm long, solid in one piece stainless steel barrel tower bolts of extruded section complete all as specified and directed.

S&F 150mm size solid in one piece stainless steel handles, D type all in 304 grade and fixed in stainless steel screwsall as directed complete all as specified and directed by Engr-in-Charge.

S&F 125mm size solid in one piece stainless steel handles, D type all in 304 grade and fixed in stainless steel screws all as directed complete all as specified and directed by Engr-in-Charge.

S&F magnet catcher for cub board with brass body and striking plate including letting in and fixed complete all as specified and directed.

S&F 250mm long stainless steel sliding door bolts 204 grade, hasp and staple type with bright bolt not less than 16mm dia with and incl a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and complete all as specified as directed.

S&F floor door stopper of stainless steel double legged and tongue, 304 grade anodised, with hard drawn steel spring, fixed in floor, overall length of cover plate 50mm complete all as specified as directed.

S & F 300 mm mild steel, ordinary rat tail rod pattern spring welded to steel/fixed to wooden door frame including roller and roller plate complete all as specified as directed.

S&F in repair 25 mm dia thickness 1mm stainless steel 202 grade curtain rod with bright nickle decorative finnial and fixed to wall with PVC dash fastner complete all as specified and directed by Engr-in-charge . Note : Cost of one pair of side brackets is inclusive in the rate per metre length of curtain rod

M&L cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves lintels etc and cutting chases for concealed water tubing etc and making good cutting not exc 10cm girth complete all as specified as directed.

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 15 mm bore GI tubing complete including taking down existing GI pipe all as specified as directed.

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 20 mm bore GI tubing complete including taking down existing GI pipe all as specified as directed.

Supply and fixing in repairs PVC connection 15 mm dia 450 mm long with PTMT nuts at both ends complete all as specified as directed.

S&F in repair sink with drainage board, overall size 915mm x 460mm bowl size 410mm x330mmx 160mm, made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste fittings / coupling including 32 mm waste pipe over and incl beding in cement mortar to dwarf wall or including fixing cantiliver brackets and connecting unoin to pipe complete all as directed

S&F in repair viterous china squatting pan (orissa pattern) long pan size 580x440mm white with integral footrest with cast iron spun 600 mm long 'P' trap fixed with epoxy mortar (Asian/Berger), set in cement concrete type B-1 (1:2:4) complete (excluding flushing cistern and flush pipe) complete all as specified and directed by Engr-in-charge

S&F in repair 08 Litr Dual capacity PVC low level flushing cistern including PVC syphon and float valve including PVC flushing bend 600 mm long and fixing with WC complete complete all as specified and directed by Engr-in-charge (Make: commander/ Cera/ Hindware/ pearl).

S&F in repair vitreous china wash hand basin, white flat back, size 440x550mm excluding taps but including waste pipe, CP waste fittings 32mm size long shank,brass and MS brackets all as specified and directed by Engr-in-charge Make: Make : Cera/Jaquar/Parryware

S&F in repair 75mm dia UPVC (SWR) pipes 4kgf/cm2 single socketed in any length jointed with rubber ring joints and adhesive fixed to wall with PVC clamps, complete all as specified and directed.

S&F in repair 110mm dia UPVC (SWR) pipes 4kgf/cm2 single socketed in any length jointed with rubber ring joints and adhesive fixed to wall with PVC clamps, complete all as specified and directed.

S&F in repair 75mm dia UPVC (SWR) pipes 4kgf/cm2 single socketed in any length jointed with rubber ring joints and adhesive laid in trenches or in floors complete all as specified and directed.

S&F in repair 110mm dia UPVC (SWR) pipes 4kgf/cm2 single socketed in any length jointed with rubber ring joints and adhesive laid in trenches or in floors complete all as specified and directed.

S&F in repair 150mm dia UPVC (SWR) pipes 4kgf/cm2 single socketed in any length jointed with rubber ring joints and adhesivelaid in trenches or in floors complete all as specified and directed.

S&F UPVC (SWR) bend 'T', with access door socket, Reducer etc. jointed with adhesive for 75 mm bore pipes complete all as specified and directed.

S&F UPVC (SWR) bend 'T', with access door socket, Reducer etc. jointed with adhesive for 110 mm bore pipes complete all as specified and directed.

S&F in repairs PVC tank lid/cover threaded with frame fixed with the existing water storage tank (cylindrical) for 500/1000 ltrs capacity tanks, complete all as specified and directed by Engr-in-charge

S&F in repair pillar taps, brass, with capston heads, fancy type chromium plated, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed. Make : Jaguar/Cat part No. KUP-35001PM/Hindware Cat Part No:F370001/Parryware Cat Pat No.T4302A2

S&F in repair brass chromium plated ovehead shower with shower arm complete all as specified and directed. Make : - Parryware Cat Part No T9985A1(Shower) & T-9999A1(Arm)/Hindware Cat Part No F160054 (Shower) & F190016(Arm)/Jaquar Cat Part No OHS 1999 (Shower) & SHA479L300 (Arm).

S&F in repair concealed stop cock, brass, with capston heads, fancy type chromium plated, screwed down high pressure with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed. Make :Jaquar/Hindware/Parryware

S&F in repair angle stop cock, brass, with capston heads, fancy type chromium plated, screwed down high pressure with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed complete all as specified and directed. Make : - JAGUAR Cat Part No FON-40053/Hindware Cat Part No F160017/Parryware

S&F in repair 15mm bore Bib taps short body, cast copper alloy fancy type chromium plated with, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. Make : - JAGUAR CAT Part No ALI-85037/Hindweare CAT Part No F-370004/Parryware

S&F in repair soap dish, brass, chromium plated,100X100X60mm, fixed to wall with rawl plugs and chromium plated screws complete all as specified and directed. Make : Jaquar/Hindware/Parryware

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf with chromium plated guard and railling size 500x125mm (with brass bracket) complete all as specified and directed. Make : Jaquar/ Hindware/ Parryware.

S&F in repair stainless plate rack of size 600mmx750mmx200mm made out of 1 mm thick stainless steel sheet complete all as specified and as directed. Make : Prayag/Blue star / Sliver sine.

S & F in repair PTMTgrating square 150 mm size complete all as specified. Make : Prayag Cat No. 115 or equvilant

S&F in repair Stainless steel cockroach Trap square of size (101X101 mm) complete all as specified and directed. Make : Prayag Cat No. FT 21 or equvilant

S&F in repair 20 mm dia brass chromium plated tubular towel rail 'D' type 60 cm long between flanges, including one pair of fixing brackets complete all as specified and directed.

Cleaning of existing PVC/RCC water storage tank with vaccum cleaner machine exc 250 to 500 ltrs capacity with liquid bleach and dry with and apply on coat of anti bacterial spray as directed by Engr-in-charge. Date of cleaning to and CA No to be painted on water storage tank with stencil in black/ white synthetic enamel paint all as directed by Engr-in-Charge.

S&F rotational moulded polyethylene water storage tanks 500 Ltrs capacity three layered, externally white (cylindrical vertical with closed top) hoisted and fixed in position including PTMT ball valve 20mm bore with polythelene float including dismantling of existing unserviceable tank and removing from site complete all as specified and directed.

Supply only water proofing compound Dr. Fixit / Fosroc

S&F in repairs 75mm dia centrifugally Cast iron spun (SI-3989-1984) floor trap with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed by Engr-in-charge

S & F in repairs 20 mm bore gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete.

S & F in repairs ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size (Minimum weight 210 gms) complete.

S&F in repair of Aluminium body door cill at bottom rail of door to stop entry of insect inside the room complete all as specified and as directed.

S & F in repair acreylic glass corner shelf with CP brass railing size not less than 300 mm long and fix to wall with rawl plug and CP screws complete all as specified and directed. Make : Jaquar/Hindware/Parryware

Dismantling asbestos cement sheet and ridges (corrugated, semi corrugated) and ridges in roof covering etc.

M&L for 6 mm thick asbestos cement corrugated or semi corrugated sheets in roof fixed with 'L' type or J type or cranked hook bolts complete.

S&F Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified and directe by the Engr-in-Charge.

S&F Pre painted galvalume aluminium zinc coating GI based steel sheet ridge 0.50 mm thick of an colour having tensile strength of 550 Mpa made to profile of roof sheet, fixed with self tapping screws as specified all directed by the Engr-in-Charge.

S&F in repairs tiled false ceiling of Designer tile Ivory painted (High PressureSteam cured) of 4mm thickness (as per IS : 14862) of size 595x595mm and any one of the design (Cascade or electra) in true horizental level, suspended on inter locking metal grid of hot dipped galvanised steel section (Galvanised @120 grms, both side inclusive and black painted groove on all T webs) consisting of main T runner with suitably spaced joints to get required length and 15x32mm made from 0.30mm thick sheet spaced at 1200mm c/c and croos 'T' of size 15x32mm made of 0.30mm sheet 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600mm and secondary cross "T" of length 600mm and size 15x32 mm made of 0.30mm thick sheet to be interlocked at middle of

All as per item No 120.00 Contd/-----the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x22x0.40mm and laying false ceiling tiles in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanised Butterfly level clips, spaced at 1200mm c/c along main 'T', bottom exposed width of 15mm of all 'T'' sections of 3mm dia GI wire shall be pre-painted with polyester paint and black painted groove at center of size 4mm depth and 4.5mm width, all complete at all heights including taking down existing false ceiling of ant type as per direction of Engineer-in-Charge.

S&F in repairs structural steel for roof trusses (framed) , purlins, crane gantries, rails and fastenings and heavy bracket framing (Pipes, Beam, Tee, Angle, Channel or Flat sections) including distance pieces, cleats etc.complete all as specified and directed by Engr-in-charge

M&L for MS work as in fencing posts including flat iron, nut & bolt for securing the wire mesh complete all as specified and directed.

S&F mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips (TMT)

M&L for TMT bars 8mm dia cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed.

M&L for RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in slabs supported on walls, beams and colums, in floors, roofs, landing balconies, canopies, deck slabs, chajja and in shelves and the like, complete including demolition of existing surfaces all as specified and directed.

Fixing only Chain link fencing including line wires, any mesh size and type to any type of standards rails straining bolts etc including provision of binding wire complete all as specified and directed by Engineer-in-Charge.

Supply only Chain link fencing mesh size 100mm x 100mm, dia of wire 3.15mm as approved by Engineer-in-Charge.

M&L for cement concrete 1:3:6 type C2 (using 40 mm graded stone aggregate) in walls or retaining walls,any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases) complete ncluding demolition of existing surfaces all as specified and directed.

S&F Mild steel flat iron for securing of chain link fencing including fabrication i.e. cutting, drilling holes, welding etc..complete all as specified and directed.

Mild steel bars round bars 10 mm dia cut to length, bent to shape required as in chain link fencing complete all as specified and directed.

S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut exc 15cm but not.exc 22.5 cm long,diameter of neck n exc12 mm complete all as specified and directed.

Taking out existing roof treatment completely upto PCC / RCC surface and M&L for water proofing treatment on roof slab including picking, sweeping clean and washing down with water to remove dust & providing water proofing treatment described as under:- (a) Surface preparation and treating of construction joints, filling of honey combs with polymer modified mortar (Cement: Sand : smart care multipurpose polymer of Asian Paints or equivalent product of Thermax/ Berger ) (b) Providing PCC (1:2:4) type B-0, 25mm thick screed bed or bedding layer over roof surface .

Item No 132.00 contd/---. (c) Cleaning the surface and applying (Resin & Hardner) smart care Epoxy Primer 2k of Make Asian paints or equivalent product of Thermax/ Berger ) on the cleaned surface for bonding of PU magnum with the existing concrete surface. (d) Supplying, providing and applying waterproofing treatment to Terrace area with Asian Paints Smart care PU magnum, single component highly elastomeric seamless cold applied modified PU coating or equivalent product of Thermax/ Berger) including all necessary surface preparation, coving using smart care multipurpose polymer, water pond test, etc. complete as per manufacture's specifications and application methodology. The same coating shall be applied in two coats achieving a total thickness of 1mm. The coating shall have dual combination of 250% elongation . Execution to be done with authorised applicator of the manufacturer. Work will be executed in smart assurance system.

Cleaning of man holes of any depth and size including clearing the mouth of outlet/inlet pipes, by taking out accumulated soil, sludge etc mechanically and removal out of MD land and refixing manhole cover all as directed by Engr-in-charge.

M&L for dewatering and desludging of septic tank / soakage well of any size and depth by mechanical pumping by plugging inlet as requried, including effluent, solids and sludge out of MD land includind removing the manhole covers and reinstating to its original postion complete all as specified and directed by Engr-In Charge. (Note: A particular septic tank / soakage well which is undertaken once for cleaning and paid for shall be kept functional for entire contract period and no extra payment for repitetive cleaning if requred shall be made)

Pumping out sewage water from the man holes / septic tank / soakage well at different locations by means of sewage tanker fitted with pump (5000 ltr capacity) and disposing off out of MD land as directed by Engr-in-charge .

Excavation in trenches in any type of soil not exceeding 1.5M wide and not exceeding 1.5M in depth for sewage line, manhole etc not exceeding 10 sqm on plan and getting out in any type of soil complete.

Dismantling and taking out from trenches salt glazed stone ware / RCC pipes and fittings 150mm bore including PCC benching and haunching complete all as specified and directed. (Excavation shall be measured and paid for seperately)

Dismantling and taking out from trenches salt glazed stone ware / RCC pipes and fittings 200mm bore including PCC benching and haunching complete all as specified and directed. (Excavation shall be measured and paid for seperately)

S&F, laying, jointing and testing salt glazed stone ware drain pipe 150 mm Internal dia, grade ‘A’ confirming to IS–651–1980 laid in trenches and jointed in cement mortar 1:1 complete

S&F, laying, jointing and testing salt glazed stone ware drain pipe 200 mm Internal dia, grade ‘A’ confirming to IS–651–1980 laid in trenches and jointed in cement mortar 1:1 complete

M&L for PCC (1:3:6) type C-2 (using 40 mm graded stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore pipe complete all as specified and directed.

M&L for PCC (1:3:6) type C-2 (using 40 mm graded stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 200 mm bore pipe complete all as specified and directed.

Returning, filling in, including spreading, watering and well ramming in layers n. exc 25 cm thick in any type of soil complete.

Removing excavated material to a distance n exc 50m and deposited where directed at a level n. exc 1.5M above the starting point complete.

M&L in repairs for 60 mm thick vibromatic reinforced precast cement concrete 1:1:2 (using 20mm graded stone aggregate) with 2mm thick mild steel CR sheet around painted with 2 coats of bituminous paint , as in man hole cover slabs finish fair even and smooth without using extra cement ( Top surface will be chequred finish) including necessary form work, 100 mm long handle of 12mm dia round bar counter sunk by 25mm welded to reinforcement complete all as specified and directed by Engr-in-charge (Note : CA No and date will be engraved on covers. Reinforcement shall be measured and paid saperately. Curing will carried out with ponding method)

M&L Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted built in cement mortar 1:6 including demolition of existing old brick work or stone masonary built in cement mortar including all quoins, arches, pillars etc complete including demolition of existing stone all as specified and directed

All as per Item No. 146.00 here in above but except stone complete. Note : Old serviceable stone obtained from demolition shall be reused. The rate quoted against this item is inclusive of necessary cleaning and stacking of stone before incorporation in the work.

S&F Factory made solid panel Fibre reinforcement plastic (FRP) door shutter 30mm thick consisting of frame top & bottom rails as per SSR Part I, any number of panels, the rasin of chemical used in door of unsaturated polyester rasin catagory, cataylst used of methyl Ethyl Ketone peroxide (MEKP)/benzyl peroxide/acetyl aceto peroxide. Accelerator used of cobalt napthalate/cobalt octonate/N.N Dinethyl aniline. Timber suitable for manufacturing of FRP products is in accordance with IS 12896. The timber used for frames is seasoned upto the permissible moisture content as per IS-287 : 1993. Pigment compatible with unsaturated polyester resin is used to obtain the shade of finish complete all as specified and directed by the Engineer-in-Charge.

S&F Factory made solid Fibre reinforcement plastic (FRP) frame of size 75mmx50mm the rasin of chemical used in door of unsaturated polyester rasin catagory, cataylst used of methyl Ethyl Ketone peroxide (MEKP)/benzyl peroxide/acetyl aceto peroxide. Accelerator used of cobalt napthalate/cobalt octonate/N.N Dinethyl aniline. Timber suitable for manufacturing of FRP products is in accordance with IS 12896. The timber used for frames is seasoned upto the permissible moisture content as per IS-287 : 1993. Pigment compatible with unsaturated polyester resin is used to obtain the shade of finish complete all as specified and directed by the Engineer-in-Charge.

Dismantling of barbed wire fencing any type complete all as specified and directed.

Dismantling posts or struts any section including takingout embedded portion and making good disturbed ground complete all as specified and directed.

Excavation in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around in layers n exc 25cm watering and removing surplus soil to a distance n exc 50m and making good surface in hard / dense soil complete all as specified and directed.

Taking down carefully copper/Aluminum point wiring (light, fan socket and power) complete including switches, ceiling rose lamp holder and regulator etc and removing from site and making good disturbed surfaces of walls/floors etc complete all as specified and directed by Eng-in-charge.

M&L for point wiring with 1.5 Sqmm. (nominal area) FRLS, single core PVC insulated 1100 Volts, grade multistranded copper conductor unsheathed in and including concealed PVC conduit medium duty 20 mm dia or higher and heavy grade conduit fittings and heavy duty accessories with suitable size of sunk type cast iron or pressed steel terminal box 1.6mm thick for mounting of switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet as top cover, one green colour FRLS cable of same size as earth wire up to common earth and connected to earth dolly compete all as specified and directed by Eng.-in-charge of following. Make of PVC Wire: Havells/KEI/Finolex/L&T. Note: The wiring to be done as per IE rule and maintain colour code accordingly.

(a) One light point point /bell buzzer point controlled by one-one way switch.

(b) One ceiling fan/Exhaust fan point controlled by one-one way switch through Regulator.

(c) One three pin 5 Amp socket on same board with other switches.

(d) One three pin 5 Amp socket on independent board

(e) One light point controlled by two way switch

All as per Item No 154.00 here in above but one three pin 15 Amps switch socket out let on the independent board with 2.5 sq mm PVC insulated FRLS copper conductor and 2.5 Sqmm FRLS copper conductor for continuous earthing complete.

M&L for point wiring with 1.5 Sqmm. (nominal area) FRLS, single core PVC insulated 1100 Volts, grade multistranded copper conductor unsheathed in existing PVC / Steel, concealed and existing MS boxes, mounting of switches, sockets, fan regulator etc with 3 mm thick plastic laminated sheet as top cover, one green colour FRLS cable of same size as earth wire up to common earth and connected to earth dolly compete all as specified and directed by Eng.-in-charge of following Make of PVC Wire: Havells/KEI/Finolex/L&T. Note: The wiring to be done as per IE rule and maintain colour code accordingly

(a) One light point point /bell buzzer point controlled by one-one way switch.

(b) One ceiling fan/Exhaust fan point controlled by one-one way switch through Regulator.

(c) One three pin 5 Amp socket on same board with other switches.

(d) One three pin 5 Amp socket on independent board

(e) One light point controlled by two way switch

All as per Item No 156.00 here in above but one three pin 15 Amps switch socket out let on the independent board with 2.5 sq mm PVC insulated FRLS copper conductor and 2.5 Sqmm FRLS copper conductor for continuous earthing complete.

S&F switch piano flush button type 5 Amps SP 250 V AC complete all as specified & directed.

S&F switch piano flush button type 15 Amps SP 250 V AC complete all as specified & directed.

S&F socket outlet multipurpose 3 Pin 5 Amp and 2 Pin 5 Amps 250 V AC complete all as specified & directed.

S&F socket outlet two in one three pin 5 Amp and 15 Amp 2 module 120 W flush type complete al as specified.

S&F Bell switch paino flush button type 5 Amp complete all as specified.

S&F ding dong bell AC 230 V single pole complete all as specified and directed .

S&F switch paino flush button type 5 Amp SP 2 way complete 250 V AC all as specified and directed.

S&F step type regulator socket type double module 5 step for ceiling fan 1200/1400 mm size 230 volts 6 Ampds 400 watts.

S&F ceiling rose, 3 terminal/PVC/polycarbonate, isolated body 250 V AC.

S&F lamp holder, pvc/polycarbonate type with back plate suitable for batten fittings including 9Watt LED bulb complete all as specified & directed.

M&L for sub main wiring with 2 Single core PVC insulated unsheathed cable 1100 Volts grade heavy duty copper conductor multistranded of size 6 Sqmm (nominal area) and one single core green colour PVC Insulated unsheathed cable copper conductor multistranded of size 6 Sq mm as earth wire upto common earth and connected to earth dolly drawing through and incuding PVC medium grade conduit 20mm dia complete incl taking out old unserviceable submain all as specified & directed. Make: Havells/Finolex/L&T

S&F in repairs sheet metal enclosures 240 volt with 200 Amp rated bus bar for double door 8 way DB,s IP-43 IK 09 metal door suitable for one MCB SPN as incoming and 06 MCB SP as out going complete all as specified and directed. Make: Legrand/ Schneider/ ABB.

S&F in repairs sheet metal enclosures Triple pole and neutral double door 415 Volt 4 way DBs IP-43 IK- 09 Vertical type suitable for 200 Ams rated bus bar & one MCCB 100 Amp as incoming and 12 MCB SP as outgoing complete all as specified and directed Make Legrand/Schneider/ABB.

S&F MCB double pole 240 Volt 10 KA 40 Amp 'B' series conforming to ISI marked complete all as specified & directed Make Legrand/Schneider/ABB.

S&F MCB single pole and 240 volt 10 KA 5-32 Amp 'B' series conforming to ISI marked all as specified and directed Make Legrand/Schneider/ABB.

S&F MCCB 415 Volt 16 KA 4 pole 63 Amp magnetic trip release & setting as incoming with fixing arrangement complete all as specified and directed. Make Legrand/Schneider/ABB.

S&F in replacement wall mounted tube light fitting 1x20/22 watts extruded aluminium polycarbonate covers PF 0.9 and above operating voltage 140V-270V colour temp 6500K & lumen input output 95 Lumen per watt and connected to ceiling rose with required length of two core flexible copper cable 23/0.0076 fixed on wall/roof complete all as specified and directed. Make: Philips cat part No TMC 501P1xT LED 22WP-3241(Tube Batten) and MAS LE$D 1200mm 18W-865-T-81 (Tube) / Wipro Cat part No WI0922208 (Tube Batten) LL13-181-65SE (Tube)/ Havells Cat Part No LUMILINEPLUSBS20WLED865SPCSS (Tube Batten)CRYSTAL1213T8DSTL20WLED865SGLASS(TUBE DOUBLE SIDE)

Supply, Fixing and testing in repairs LED down lighter recessed mounted 2x2 feet36W ultra modern designed LED luminaire which provide soft light and glair free symmetrical illumination suitable for grid ceiling and connected to ceiling rose with required length of two core flexible copper cable 23/0.0076 fixed on as per Havells Cat Part no: ENDURASLIMPROPLUS2x2PLR28/36WLED 840MOD or equivelent make of PHILIPs/ CROMPTONall as directed by Engineer-in-Charge.

S&F in repairs LED light fitting 1x10 w bulk head fitting complete with accessories and including connecting up with twin core twisted flexible copper conductor cable of suitable size Make:WIPRO CAT PART NO-LW07-141-XXX-57XXor equivelent , HAVELLS/CROMPTON

S&F in replacement LED light fitting decorative wall mounting SS brush finish fixture with frosted glass suitable for upto 1x40 watt mini glass lamp with and including one no 12 watt LED lamp. complete with accessories and including connecting up with twin core twisted flexible copper conductor cable of suitable sizeAs per Havells Cat Part NO LHFOAJE1TN1IO60 or equivelent of Bajaj/ Philips.

S&F in repairs mirror light decorative compact luminarious with decorative ends caps 9/10 Watt LED with all accessories and including connecting up with three core flexible copper conductor cable of suitable size . Make Havells Cat No Edgelite or equilent in Philips/Wipro

S & F in repairs high efficiency LED bulbs 1 X 12 watt that can be used as a ready replacement for existing GLS ad CFL direct fit in holder complete all as specified and directed.

Supply and Fixing in repairs Integral LED Street Light Luminaire comprising of pressure die cast aluminum housing heat resistant toughened glass with frame IP-65 protection road way luminaries with high power LED 40/45 watt with efficiency 100 lumen/watt at system level, CCT>5700K, with average life class 50,000 burning hours, complete all as specified and directed. Make:- Crompton model No. LSTP-45-CDL/Havells model No. ENDURAPEARLNEOSL 40WLED757PASYTOPC /Philips Cat Part No BRP409LED CW036MRFGIPSUGRand syska SSK-ST-40W including taking out old unserviceable street light.

M&L in repairs for service cable 6 sq mm twin core Weather proof aluminium multistranded conductor cable PVC sheathed PVC insulated round suspended with No.8 SWG GI wire and reel insulators at distance of 01 mtr duly connected with earthing and clamp etc from Pole to pole completeMake of PVC Cable Havells/KEI/Finolex/L&T.

All as per Item No 181.00 here in above but 10x2 sq mm Make of PVC Cable: Havells/KEI/Finolex/L&T.

S&F in replacement electronic ballast for existing tube light fitting 40/36 Watt complete all as specified and directed. Make: Bajaj/Philips/Havells

Supply and fixing in repairs LED tube rod 18/20 Watts single or double sided connections polycarbonate complete incl making connection alteration in existing tube light fitting complete.

Disconnecting electric connection and taking down of ceiling fan / Exhaust fan of any sweep complete carefully for overhauling, removing capacitor, split pins checking of bearings/bush, cleaning the fan blades with cleaning solution, replacing the unserviceable bearing, bush, capacitor , safety split pin and nuts, bolts, washer etc, cutting threading down rod if required, reassembling the ceiling fan complete after greasing/servicing, oiling testing the same making the fan in serviceable condition and refixing/ hanging the same complete all as specified and directed by Engineer-in-Charge (Note: Bush, bearing, capacitor, down rod, hanging clamps, will be paid under relevant item of this Schedule). Cost of split pins, nut bolts and threading of down rod pipe rates are included in quoted rate)

Supply only fan capacitor 2.5 mfd make universal / Asian/Epcos .complete all as specified and directed

Supply only fan capacitor 4 mfd complete all as specified and directed make universal / Asian/Epcos

Dismantling electric and water connection of the 25/50 ltr's geyser, taking down from its original position on ground, opening up and removing apparatus plate from the tank, descaling the geyser inner tank and apparatus plate complete, checking for defects, replacement of unserviceable parts such as heating element, syphon assembly, thermostat, rubber gasket etc., reassembling and installation of the geyser into its original position and connecting all electric and water supply connection and testing on completion all as directed by Engineer-in-Charge.(Notes: (i) Heating element, syphon assembly, thermostat, rubber gasket etc if required to be replaced shall be measured and paid separately. (ii) Nut, bolts and hold fastners if required to be replaced shall be deemed to be included in the quoted rates of this item. (iii) Payment for a geyser will be made only once through out the contract period irrespective number of repair carried out in same Geyser.

Supply only heating element any type/size as per site requirement of capacity 2 KW ISI Marked. Make:-Theta/Newton/Dasmesh/Bajaj

Supply only thermostat for geyser long type 11" in length as per site requirement temp setting on 60 degree centigrade ISI Marked, long type complete all as specified and directed. Make: Dashmesh/Indofors/Donfoss/Bajaj

S&F in replacement of water supply PVC flexible connection nylon braided with suitable threaded check nut with washer complete suitable for hot / cold water 15mm dia alongwith threaded brass nuts and washers 45 cm long complete all as specified and directed. Make:- POLO/Havells/Prayag

Supply only pressure release valve as per existing make and size geyser spring loaded 15 mm dia complete all as specified and directed.

Supply only rubber Gasket as per existing make/size site requirement suitable for 25/50 Ltr capacity geyser complete all as specified and directed.

S&F in replacement Sheet metal enclosure SPN with a two pin and earth plug and socket complete with one 20 amp single pole MCB complete all as specrified & directed

M/s Teg Singh Negi

M/S C S AITHANI