SPECIAL REPAIR TO GUEST HOUSE AND PROVN OF SHED AND GALVALUME SHEET COVERING IN ROOF TOP OF GUEST HOUSE AND LADIES TOILET AND COVERED PASSAGE AT PCDA (AF) DEHRADUN UNDER AGE B/R-III OF GE CLEMENT TOWN

Amount

Demolition of cement concrete (Un-reinforced) in ground floors and pavings n.exc 15cm thick (above or below GL) complete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engr-in-Charge.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed by Engr-in-Charge.

Demolition of brick work or stone masonry built in cement mortar including all quoins, arches, jambs etc complete all as specified and directed by Engr-in-Charge.

Dismantling of boarding of any type/size as in CB/wardrobes or fixed in any position in hardware (if any) etc complete all as specified and directed by Engr-in-Charge.

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engr-in-Charge.

Taking down cement plaster of any description on brick work or stone masonry walls including rackingout joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engr-in-Charge.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame) of size n.exc 1.50 Sqm complete all as specified and directed by Engr-in-Charge.

Taking down chowkhats or frames with shutters (without taking off shutter from the frame) of size exc 1.5 Sqm and n.exc 4 Sqm complete all as specified and directed by Engr-in-Charge.

Taking down shutter of any description exc. 1 sqm but not exc. 2 sqm each complete all as specified and directed by Engr-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/springclips and providing and fixing new one complete all as specified and directed by Engr-in-Charge.

Taking up or down 15mm dia steel tubing and connections including cleaning for re-fixing or removal from site complete all as specified and directed by Engr-in-Charge.

Taking up or down 20mm dia steel tubing and connections including cleaning for re-fixing or removal from site complete all as specified and directed by Engr-in-Charge.

Disconnecting existing water storage tanks of capacity exc 500 ltr but n.exc 1000 ltr, setting aside (or lowering if required) for repairs, cleaning and removing all scales and dirt, etc and refixing in same position complete all as specified and directed by Engr-in-Charge.

M&L brick work with sub class "B" old size bricks, straight or curved on plan exc 6m mean radius built in cement mortar (1:6) complete all as specified and directed by Engr-in-Charge.

M&L for half brick work with subclass ‘B’ bricks, straight or curved on plan to any radius built in CM 1:4 complete all as specified and directed by Engr-in-Charge.

M&L for Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed by Engr-in-Charge.

M&L for 25mm thick PCC (1:2:4) type B-0 (using 12.50mm graded stone aggregate) as in sub base of floor complete all as specified and directed by Engr-in-Charge.

M&L 75mm thick PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in sub base of floor complete all as specified and directed by Engr-in-Charge.

M&L RCC (1:2:4) type B-1 (Using 20mm graded stone aggregate) as in slabs, shelves supported on walls, beams and columns in floor or roof including balconies, canopies, deck slabs or in Chajja/facia projection and the like complete all as specified and directed by Engr-in-Charge.

M&L mild steel TMT bars 10mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-Charge.

M&L for use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick for fair finished surfaces (Horizontal or sloping) complete all as specified and directed by Engr-in-Charge.

M&L for Non skid Endura coloured tiles 8-10mm thick (square/rectangular) grade-4, area of each tile exc 0.06 Sqm but not exc 0.11 Sqm over and including 15mm thick screed bed in Cement mortar (1:6) in flooring, set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed by Engr-in-Charge.

M&L for Non skid Endura coloured tiles 8-10mm thick (square/rectangular) grade-4, area of each tile exc 0.06 Sqm but not exc 0.11 Sqm as in vertical surface such as dado/ skirting etc over and including 10mm thick screed bed in Cement mortar (1:4) in flooring, set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed by Engr-in-Charge.

M&L for joint free Non-skid ceramic coloured tiles 7-8mm thick (square/rectangular), area of each tile not exc 0.11 Sqm, over and including 15mm thick screed bed in CM (1:6) in flooring, set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed by Engr-in-Charge.

M&L for Glazed ceramic coloured joint free tiles 600x300X7-8mm in vertical surfaces over and including 10mm thick rendering in Cement mortar (1:4), set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed by Engr-in-Charge.

M&L Vitrified coloured tiles 8-10mm thick any shade (Square/Rectangular) double charged area of each tiles exc 0.42 sqm but not exc 1.00 sqm over and including 15mm thick screed bed in Cement mortar (1:6) in flooring, set and jointed in neat cement slurry and pointed in cloured cement to match complete all as specified and directed directed by Engr-in-Charge.

M&L Vitrified coloured tiles 8-10mm thick any shade (Square/Rectangular) double charged area of each tiles exc 0.42 sqm but not exc 1.00 sqm, as in skirting/dado, over and including 10mm thick screed bed in Cement mortar (1:4) in flooring, set and jointed in neat cement slurry and pointed in cloured cement to match complete all as specified and directed directed by Engr-in-Charge.

M&L for 18-20mm thick granite (of any type and any shade) work (table rubbed and polished) stone slab as in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust to match with marble shade over and including cement screed bed 15mm thick in CM (1:6) complete all as specified and directed by Engr-in-Charge.

M&L for rubber moulded coloured cement concrete chequered tiles polished of size 30cm x 30cm x 25mm thick jointed in neat cement slurry and pointed in white or coloured cement and pigment to match the surface of tile as in floor over 15mm thick screed bed in CM 1:6 complete all as specified and directed by Engr-in-Charge.

M&L for Cutting or grinding old surface of terrazzo floor/Kota stone/Marble floor/dado or skirting etc with carborandum stone by hand or machine dusting of the surface, clean with oxalic acid solution and polishing with wax polish complete all as specified and directed.

S&F 35mm thick factory made flush shutter solid core construction with block board core and ply wood face panels, commercial type both sides complete all as specified and directed by Engr-in-Charge.

S&F Factory made 100% Solid WPC Brown door Frame (75mm x 50mm Single Rebate) made from 100% LEAD FREE (single extruded process) material with density 780 kg/Cum & Manufactured by an ISO: 9001-2015 certified company, all as per specification drawing as directed by the Engineer-in-Charge. The door frame should be Waterproof, Termite Proof, Fire Retardent and having excellent screw holding capacity complete all as specified and directed by Engineer-in-Charge.

S&F Factory made 100% Solid WPC Brown door Frame (100mm x 63mm Single Rebate) made from 100% LEAD FREE (single extruded process) material with density 780 kg/Cum & Manufactured by an ISO: 9001-2015 certified company, all as per specification drawing as directed by the Engineer-in-Charge. The door frame should be Waterproof, Termite Proof, Fire Retardent and having excellent screw holding capacity complete all as specified and directed by Engineer-in-Charge.

S&F Factory made 100% Solid WPC Brown door Frame (125mm x 63mm Double Rebate) made from 100% LEAD FREE (single extruded process) material with density 780 kg/Cum & Manufactured by an ISO: 9001-2015 certified company, all as per specification drawing as directed by the Engineer-in-Charge. The door frame should be Waterproof, Termite Proof, Fire Retardent and having excellent screw holding capacity complete all as specified and directed by Engineer-in-Charge.

S&F 24mm thick Moulded WPC Brown Factory made 100% Solid door (Conforming as Per IS:4020) made from 100% LEAD FREE single extruded with 2, 4 or 6 raised panel design on the front side with 10mm deep mould on single side with Wood Grain Texture and back side plain with density not less than 600 kg/cum. Manufactured by an ISO: 9001-2015 certified company. The door should be Waterproof, Termite Proof, Fire Retardent and having screw holding capacity complete all as specified and directed by Engineer-in-Charge.

S&F 30mm thick Moulded WPC Brown Factory made 100% Solid door (Conforming as Per IS:4020) made from 100% LEAD FREE single extruded with 2, 4 or 6 raised panel design on the front side with 10mm deep mould on single side with Wood Grain Texture and back side plain with density not less than 600 kg/cum. Manufactured by an ISO: 9001-2015 certified company. The door should be Waterproof, Termite Proof, Fire Retardent and having screw holding capacity complete all as specified and directed by Engineer-in-Charge.

M&L 30mm thick Factory made solid WPC (Wood Plastic composit) molded gauged door shutter with wire mesh in any number of division with brown wood grain texture, including S.S wire mesh shall be fixed with 15x15 square tube in side rails with screwing 8x28 heat metal zink coated screws can be remove or fix again after changing of wire mesh when needed. The density of the shall be as per manufacture instructuon complete all as specified and direced.

S&F three track Pre coated Steel Sliding Window System fabricated from roll formed sections made of Galvanized Steel Colour Coated/ Powder Coated (Base Steel as per IS 513 “D” quality, galvanized as per IS 277 with Zinc of 120 grams/ Sq. Mtr.) with total coated thickness of 0.58 mm or Powder Coated with pure Polyester Powder up to 50-60 microns thick. Windows Section for three track external frame should be of 44 x 107mm , Section for window glass shutter should be of 36 x 50 mm, if required Section for shutter horizontal mullion should be 22mm x 60mm, The windows should be paneled with 5mm thick Plain Float glass Gaskets are to be made with Ethyl Propylene Diamine Manomer (EPDM). Corner brackets for internal and external frame made of Polypropylene. Touch lock to be provided for window shuttes Sections are to be cut to length, joined and assembled by means of corner brackets. The above Frame should be fixed to brick/ concrete masonry by using Nylon self-expanding caps and driving MS electroplated 80mm long screws into the caps through frames.Windows shall be provided with fixed Stainless steel 32gauge wire mesh/gauze of 304grade with 144 holes per square inch for mosquito proofing with the help of nut, bolt and flat iron of 20x3mm size on top and Grill made of 12mm MS Square bars welded to 25x4mm angle iron . Distance between bars should not be more than 100mm centre to centre. Total Grill and wire mess unit shall be powder coated. Assembling and installation of windows and ventilators shall be all as per details shown/mentioned on drawings and as per manufacturer‟s instructions complete all as specified and directed by Engr-in-Charge.

S&F Pre coated Steel Windows/Ventilators fabricated from roll framed sections made of Galvanized Steel Colour Coated/ Powder Coated (Base Steel as per IS 513 “D” quality, galvanized as per IS 277 with Zinc of 120 grams/ Sq. Mtr.) with total coated thickness of 0.58mm. Powder Coated with pure Polyester Powder up to 50-60 microns thick. Windows Section for frame should be of 72mm x 55mm, Section for Shutter Frame should be of 47mm x 20mm, Section for Fixed Bead should b of 12mm x 12mm, and section for fly Mesh should be of 40mm x 20mm. Section for Frame Glazed Shutters and Mesh Shutters should be cut to length and miter joined with Polypropylene Corner Brackets, Mullion section should be joined with frame/Mullion Cap Ethyl Propylene Diamine Manomer (EPDM). Gasket should be used all around glass in shutter and fixed Glass Spoon Profile Section should be used around Fly mesh to fix Mesh in Mesh Shutter. Each Glazed shutter and Mesh shutter should be provided with SS Pivot Hinges-1 set, Seccolor Handle & Seccolor Stay. Window Frame should be fixed to brick/ concrete masonry by using Nylon self-expanding caps and driving MS electroplated 80mm long screws into the caps through frames. Glass Shutter & Fixed Glass portion should be provided with a glass of 4mm Plain/Float Glass. Mesh Shutter should be provided with a Stainless Steel 32gauge Fly mesh of 304 grade with 144 holes per square inch for mosquito proofing. Windows should be provided with Grill made of 10mm MS Square bars welded to 150mm center-to-center, 6mm x 12mm MS flat. Total grill unit shoud be powder coated and fixed to window frame with screws. Assembling and installation of windows and ventilators shall be all as per details shown/mentioned on drawings and as per manufacturer‟s instructions complete all as specified and directed by Engr-in-Charge.

S&F Pre coated Steel fixed type Ventilator fabricated from roll formed sections made of Galvanized Steel Colour Coated/ Powder Coated (Base Steel as per IS 513 “D” quality, galvanized as per IS 277 with Zinc of 120 grams/ Sq. Mtr.) with total coated thickness of 0.58 mm or Powder Coated with pure Polyester Powder up to 50-60 microns thick. The Ventilators should be paneled with glass louvers with 4mm thick frosted glass and providing space for Exhaust fan. Gaskets are to be made with Ethyl Propylene Diamine Manomer (EPDM). Corner brackets for internal and external frame made of Polypropylene. The above Frame should be fixed to brick/ concrete masonry by using Nylon self-expanding caps and driving MS electroplated 80mm long screws into the caps through frames. Assembling and installation of windows and ventilators shall be all as per details shown/mentioned on drawings and as per manufacturer‟s instructions complete all as specified and directed by Engr-in-Charge.

S&F in repair 18mm thick WPC board one side prelaminated and other side plain white colour as in cup boad shutters and frames, kitchen cabinet front shutter, partion, shelf & drawer, fixed with screws, solvent cement/ adhesive complete all as specified and directed by the Engineer-in-Charge.

S&F 100mm long mild Stainless Steel butt hinges, medium weight cold rolled complete all as specified and directed by Engr-in-Charge.

S&F 150mm long, Stainless Steel barrel tower bolts complete all as specified and directed by Engr-in-Charge.

S&F 150mm size Stainless Steel handles, all as directed complete all as specified and directed by Engr-in-Charge.

S&F 250mm long (Length of bolt) Stainless Steel sliding door bolt with hasp, staple (bolt type) and fixing clips of sheets, and fixing bolts and sliding bolt complete all as specified and directed by Engr-in-Charge.

S&F D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 100mm long matt finished complete fixed in position all as specified and directed by Engr-in-charge.

S&F Ball catchers 304 grade stainless steel finished suitable for cabinets premium quality complete fixed in position as per manufacturer's instructions all as specified and directed by Engr-in-charge.

S&F in repair Hydrulic Self Closing hinges 35mm of crank( KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete in all respect and fixed in position complete all as specified and directed by Engr-in-Charge.

S&F in repair door closer parallel arm aluminium (extruded section) body hydraulically regulated, designation No. 3, universal type, complete all as specified and directed by Engr-in-Charge.

S&F in repairs mortice lock, vertical type with brass body 6 lever with brass latch bolt and locking bolt with SS handle complete all as specified and directed by Engr-in-Charge.

S&F in repair of 140mm Floor door stopper of Stainless Steel body and tongue, with hard drawn steel spring, fixed in floor, Overall length of cover plate complete all as specified and directed by Engr-in-Charge.

S&F 25mm dia Stainless Steel Curtain rod fixed to wall with Stainless Steel brackets and end Knobs incl all fixing arrangment complete all as specified and directed by Engr-in-Charge.

M&L 15mm thick rendering in cement mortar (1:6) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L 15mm thick rendering cement mortar (1:4) mixed with liquid water proofing compound on fair faces of brick work or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified and directed by Engr-in-Charge. (WPC shall be paid seperately)

M&L for 10mm thick plaster on roof, chajja and roof parapet of CM (1:3) on RCC finished even and smooth without using extra cement etc ncl taking down cement plaster complete all as specified and directed by Engr-in-Charge.

M&L 5mm thick rendering in ceiling of cement mortar (1:3) on fair faces of brick work or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified and directed by Engr-in-Charge.

Supply only liquid water proofing compound complete all as specified and directed by Engr-in-Charge.

M&L preparation of new plastered surfaces with wall care putty and applying two coat of acrylic distemper over a coat of primer on walls complete all as specified and directed by Engr-in-Charge.

M&L for preparation of newly plastered surface of external wall all as prescribed by manufacture of paint and applying two coats of exterior anti fungal acrylic emulsion paint (Weathercoat of Berger paint or Apex in Asian paint, Nerolac etc having four years of performance warranty) over a coat of exterior water based primer and external putty of same make all as specified and prescribed by manufacture of paint and as directed at site by Engineer-in-Charge. Note:- (i). The newly plastered surface must be prepared in a manner so that there should not be any impression of dent and it should be made even all as per manufacture instruction before application of emulsion paint. The cost of all materials, T&P and labour required for preparation of surface are deemed to be included in the rates quoted. (ii). The work must be got executed through authorised applicator of manufacture after concluding an MoU with manufacture for company back guarantee by the contractor. The authorised applicator of manufacturer shall be got approved from GE/ AGE (I) before commencement of work. (iii). All the material to be incorporated in the work shall be brought by contractor to MES store yard which will be subsequently issued by deportment for incorporation in the work to ensure the quantity to be consumed all as per recommendation of manufacture. (iv). after carrying out preparation of surface the same shall be got approved from GE /AGE (I) before application of distemper for each building. (v). The colour / shade will be all as approved by GE / AGE (I) (vi) The cost of Scaffolding wherever required are deemed to be included in the rates quoted by the contractor

M&L for preparation of old decorated surface of internal wall by removing existing treatment with mechanical sander (rpm 1500-2700) along with internal dust extraction system for clean environment certified by reputed paint manufacturers and applying two coats of acrylic distemper using roller over a wall care putty to make the surface smooth all as specified and prescribed by manufacturer of paint and all as directed at site by Engr-in-Charge. Note:- (i) The old surface must be prepared in a manner so that there should not be any impression of dent and it should be made even and smooth all as per manufacture’s instruction before application of distemper. The cost of materials, labour & T&P required for preparation of surface are deemed to be included in the rates quoted. (ii). The work must be got executed through authorised applicator of manufacture after concluding an MoU with manufacture for company back guarantee by the contractor. The authorised applicator of manufacturer shall be got approved from GE before commencement of work. (iii). All the material to be incorporated in the work shall be brought by contractor to MES store yard which will be subsequently issued by department for incorporation in the work to ensure the quantity to be consumed all as per recommendation of manufacture. (iv). After carrying out preparation of surface the same shall be got approved from GE before application of distemper for each building. (v). The colour / shade will be all as approved by GE.

M&L for preparation of old decorated surface and applying one coat of acrylic distemper on ceiling surfaces complete all as specified and directed by Engr-in-Charge.

M&L for preparing old steel and iron surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engr-in-Charge.

M&L for preparing old wooden or wood based surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed by Engr-in-Charge.

M&L for preparation of old wooden surface and applying one coat of French polishing on surface of any description, width or girth including cleaning and preparing th surface including a coat of wood filler where required complete all as specified and directed by Engr-in-Charge.

S&F 15mm bore dia of medium grade galvanised steel tubing with all fittings including tank nipple and fixed complete to wall or laid in floor including cutting through walls, floors, etc and their making good with existing surface complete all as specified and directed by Engr-in-Charge.

S&F 20mm bore dia of medium grade galvanised steel tubing with all fittings including tank nipple and fixed complete to wall or laid in floor including cutting through walls, floors, etc and their making good with existing surface complete all as specified and directed by Engr-in-Charge.

Refixing of old steel tubing and connections in new or old position with all fittings to floor, wall or ceiling for 15mm bore GI tubing complete all as specified and directed by Engr-in-Charge.

Refixing of old steel tubing and connections in new or old position with all fittings to floor, wall or ceiling for 20mm bore GI tubing complete all as specified and directed by Engr-in-Charge.

Cutting chases, pinning in, making good to facing where required and pointing in Cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc and cutting chases for concealed water pipe etc and making good, cutting not exc 10cm width or girth complete all as specified and directed by Engr-in-Charge.

S&F in repair 20mm dia gun metal gate valve with iron wheel haeded screwed both ends to iron pipe and fixed complete all as specified and directed by Engr-in-Charge.

S&F in repair 110mm dia PVC (SWR) pipe single socketed, in any length with rubber ring joints, laid in trenches/floor or fixed to wall including necessary clamps complete all as specified and directed by Engr-in-Charge.

S&F in repair 75mm dia PVC (SWR) pipe single socketed, in any length with rubber ring joints, laid in trenches/floor or fixed to wall including necessary clamps complete all as specified and directed by Engr-in-Charge.

S&F in repair 75mm dia PVC (SWR) floor trap with grating including jointing with solvent cement including fixing waste pipe etc complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC (SWR) junction single, (Single T) equal or unequal 110mm bore with access door complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC (SWR) junction single, (Single T) equal or unequal 75mm bore with access door complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC (SWR) bend any radius 110mm bore complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC (SWR) bend any radius 75mm bore complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC (SWR) bend any radius 110mm bore with access door complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC (SWR) bend any radius 75mm bore with access door complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC vent cowls 75mm complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC connection 15mm bore dia 450mm long with 2 Nos PTMT nuts with washer complete all as specified and directed by Engr-in-Charge.

S&F in repair PVC waste pipe 32/40 mm dia complete all as specified and directed by Engr-in-Charge.

S&F in repair CP towel Ring 200mm dia round with round flange complete all as specified and directed.

S&F in repair CP towel rack 600mm long with 3 bottom hook complete all as spfd and directed.

S&F in repair brass CP bib tap 15mm bore fancy type screwed for iron pipe complete with wall flange complete all as specified and directed by Engr-in-Charge.

S&F in repair 15mm bore Stop valve fancy type, chromium plated with long shunk and cup (concealed type) high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified and directed by Engr-in-Charge.

S&F in repair brass chromium plated shower rose 150x150 mm size sqarrel shape single flow (ABS body chrome plated with gray face plate) with rubit cleaning system complete all as specified and directed.

S&F in repair shower arm 300mm long round shape woth 90 degree bend for wall mounted shower with stainless steel flange complete all as specified and directed.

S&F in repair CP wall mixer 3 in one system with provision for both telephone shower and over head shower complete with 15mm bore long bend pipe and wall flange complete all as directed by Engineer-in-charge.

S&F in repair CP wall mixer 3 in one system with provision for over head shower complete with 15mm bore long bend pipe and wall flange complete all as directed by Engineer-in-charge.

S&F in repair 15mm Brass CP wash hand basin mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed by Engr-in-Charge.

S&F in repair Hand shower (health faucet) with 1 mtr long long Easy flex tube in chrome finish and wall hook with N.R.V (Back Flow Preventer) tube & hook (braded Tube) complete all as specified and directed.

S&F in repair CP angular stop cock 15mm dia single way and fixed complete all as specified and directed by Engr-in-Charge.

S&F in repair CP toilet paper holder fixed to wall with CP brass screws complete all as specified and directed by Engr-in-Charge.

S&F in repair Sheet glass shelf assembly/Glass Corner assembly set of three consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed by Engr-in-Charge.

S&F in repair vitreous china white oval shaped under conter wash basin with all fixing accessories of size 510x405x185mm excluding tap but including CP waste coupling & waste pipe complete all as specified and directed by Engr-in-Charge.

S&F in repair vitreous china WHB size 505x410x185mm with full pedastal, white with flat back including CP waste coupling & waste pipe complete all as specified and directed by Engr-in-Charge.

S&F in repair Vitreous china white wash down couple closet composite P or S trap type including PVC soft seat cover white complete all as specified and directed by Engr-in-Charge.

S&F in repair Vitreous china wash down water closed pan P or S trap (Pedestal pattern) white, including connection to drain (or out going pipe) and to flush pipe, antisypthonic (excluding flushing cistern and flush pipe) complete all as specified and as directed.

S&F in repair 10 Litre capacity PVC low level flushing cistern with ball valve and handle/push button 32mm dia PVC flush pipe complete all as specified and as directed.

S&F in repairs PVC water storage tank double layer white colour cylindrical, vertical with closed top with threaded cover hoisted and fixed in position tank capacity 500 Ltr with and including ball valve high pressure of PTMT with epoxy coated Aluminum rod and high density plastic ball screwed for 25mm bore of iron pipe and making connection for inlet and outlet including dismantle of old water tank and removing from site complete all as specified and directed by Engr-in-Charge.

M&L for concrete in Sunken floor and vertical faces of walls to ease up about corners with cement concrete 1:2:4 type B0 (using 12.50mm stone aggregate) mixed with SBR Latex liquid polymer (mixed as per manufacture instructions & will be paid under relivnt item of Sch A) including using form work (straight or curved) as required complete as per directions by Engr-in-Charge.

M&L for providing cement concrete 1:2:4 type B-1 for fixing edge of interlocking/Chequered tiles and rounded or chamfered edges, coping complete all as Specified and directed by Engr-in-Charge.

M&L for post construction ATT along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linesr meter including drilling and plugging holes etc on apron complete all as specified and directed

S&F 6mm thick PVC heavy grade hollow profile designer sheet strips & channel feathered at edges of approved quality and design PVC Wall/Ceiling lining fixing with frame including all beading, matching PVC angles at all window corners with all necessary frame as required complete all as specified and directed by Engr-in-Charge.

S&F in repair Stainless Steel Patch Top Pivot plate with all necessay fittings for Glass Door shutters of thickness 8-12mm complete all as specified and as directed.

S&F in repair Stainless Steel Patch Lock with computer keys with all necessay fittings for Glass Door shutters of thickness 8-12mm complete all as specified and as directed.

S&F mild steel in joist, channel, angle, tubular poles fixed independently confirming to Fe-410W (Gde-E-250) quality-B complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coated GI based corrugated steel sheet 0.50mm thick of any colour, having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coated GI based plain steel sheet 0.50mm thick of any colour, having tensile strength of 550 Mpa as in roof covering/cladding to wall, ridge etc fixed with self tapping screws complete all as specified and directed

S&F Pre-painted galvalume aluminum zinc coated GI based plain/corrugated steel sheet 0.50mm thick of any colour, having tensile strength of 550 Mpa as in valley gutter etc fixed with self tapping screws complete all as specified and directed.

S&F Multi wall poly carbonate sheet (03 layers or more) 12 mm thick fixed to frame with screws and aluminium connecter strip at joint of two sheets complete all as specified and directed.

S&F mild steel work as in trusses, rafters, purlins etc, and the like made out of MS pipe, flat, angle or hollow sections conforming to Fe-410-W (Gde-E-250) quality-A incl all necessary cleats, gusset plates etc complete all as specified and as directed.

S&F Mild Steel Plates(plain or chequered) channels, square cut or notched (ordinary or counter sunk) forming holes, without any attachment conforming to Fe 410W(Gde-E-250) quality-A complete all as specified and directed.

M&L for preparing new steel and iron surfaces of any description over 10 CM width or girth and applying two coats of synthetic enamel paint of any tint over one coat of red oxide primer complete all as specified and directed by Engr-in-Charge.

Taking down existing roof treatment of any type any description incl PCC bedding complete all as specified and directed

M&L for providing PCC 1:2:4 (20 mm graded aggregate) as in sub base avg thickness 50 mm complete all as specified and directed

M&L for providing Non skid Endura coloured tiles 8-10 mm thick (square/ rectangular) area of each tile not exc 0.16 sqm over and incl 15 mm thick screed bed in cement mortar(1:6) in flooring set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and directed.

All as per item No.121 above but on vertical surface over and incl 10mm thick rendering in CM (1:4) complete all as specified and directed

Excavation in trenches n exc 1.5 m wide and n exc 1.5 m in depth for foundation etc. Or for shafts, wells, cesspits, manhole, pierholes etc n exc 1.5 m in depth and getting out in soft loose soil complete all as specified and directed

Returning filling in soft/ loose soil incl spreading, levelling, watering and well ramming in layers n ex25 cm

Removing excavated soil n exc 50 m and depositing where directed at a level not exc 1.5 m above the starting point

M&L for cement concrete type D2 1:4:8 (40 mm graded agg) as in foundation filling and mass concrete complete all as specified and directed

M&L for reinforced cement concrete M-25 (20 mmgraded agg) as in foundation including rafts, footings, foundation beams, bases of columns etc and mass concrete complete all as specified and directed.

M&L for reinforced cement concrete M-25 (20 mmgraded agg) as in columns, pillers, piers, posts and struts complete all as specified and directed.

M&L for reinforced cement concrete M-25 (20 mmgraded agg) as in beams, cantilevers, lintels complete all as specified and directed.

M&L for reinforced cement concrete M-25 (20 mmgraded agg) as in slabs supported on walls, beams and columns in floors, roofs, landingand the like complete all as specified and directed.

M&L for reinforced cement concrete M-25 (20 mmgraded agg) as in lintel band and the like complete all as specified and directed.

M&L for form work to rough finished surfaces of sides of concrete foundations, footings, bases of columns, raft and raft beamssides and soffits of foundation and plinth beams and similar work vertical or to batter complete all as specified and directed.

M&L for form work to rough finished surfaces of concrete of sides and soffits of floor or roof beams, lintels etc and similar work complete all as specified and directed.

M&l for Formwork to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and ditrected

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 5cm but n exc 10cm wide

M&L mild steel TMT bars 6-8mm dia and over, cut to length bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engr-in-Charge.

All as per item No. 136 above but 5 mm dia and over upto and incl 10 mm dia in stirrups, spacers and binders.

M&L for hard core of broken stone or boulders of gauge n exc 63 mm , deposited , spread and levelled in layers n exc 15 cm thick , watered and rammed to a true surface complete all as specified and directed.

M&L for 100 mm thick cement concrete type D2 1:4:8 (40 mm graded agg) as in sub base to floor complete all as specified and directed

M&L for glazed ceremic tiles in vertical surface 450x300x7-8 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm thick rendering in CM 1:4 complete all as specified and directed.

M&L for providing 75 mm thick cement concrete type C-2 1:3:6 (40 mm graded agg) as in plinth protection comlete all as specified and directed.

S&F of 100mm long mild steel butt hinges, medium weight cold rolled complete all as specified and directed by Engr-in-Charge.

S&F water closet vitreous china squatting pan 'Orissa' pattern size 580x440 mm white with integral foot rest (excl flusing cistern and flush pipe)complete incl provision of lime concrete & connection to trap incl trap

S&F PVC valve less , syphonic action type , flushing cistern 10 ltrs capacity, low level, white with inlet , ball valve, float and handle incl brackets complete all as specified and directed

S&F Vitreous China wash down water closet pan (pedestal pattern), white incl seat cover with P or S type trap complete

S&F vitreous china wash basin white flat back size 550x400mm incl 01 No. CP pillar tap 15 mm, CP waste coupling 32 mm , PVC waste pipe 750 mm long and brackets incl cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed

S&F Bib taps, cast copper alloy fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed for 15 mm bore of pipe complete.

S&F Stop valves/ angle cock, cast copper alloy fancy type chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F Chromium plated health faucet with connection pipe 1 m long complete all as specified and directed.

S&F 20 mm bore stop valve cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F 20 mm bore ball valve high pressure of PTMT epoxy coated aluminium rod and high density plastic ball screwed for iron pipe anf fixed complete.

S&F PVC connection 15 mm size of length 450 mm

S&F PVC (SWR) pipes 110 mm bore single socketed in any length with rubber ring joints , laid in floors or in trenches or to walls complete

S&F PVC (SWR) bends of 110 mm bore of any radius

S&F rortational moulded polythene water storage tanks 500 ltrs capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed

M&L for preparation of newly plastered surfaces and applying three coats of oil bound distemper over an coat of putty complete

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete

M&L for preparation of newly plastered surfaces and applying two coats of weather coat paint (Asian Apex or equivalent in Berger, Nerolac) complete all as specified an directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in any type of soil

M&L for cement concrete type D2 1:4:8 (40mm graded aggregate) as in foundation, filling and mass concrete complete all as specified and directed by Engr-in-Charge.

Surface dressing not exceeding 15 cm deep and getting out any type of soil complete all as specified and directed by Engr-in-Charge.

M&L for providing cement concrete (1:3:6) type C-2 (using 40mm graded stone aggregate) as in mass concrete ,sub base of floorcomplete all as specified and directed

M&L for Sand filling under floors or in foundation including watering and consolidation complete all as specified and directed by Engineer-in-charge.

M&L for Machine pressed precast concrete interlocking paver block any shape & size confirming to IS 15658-2006 of 60mm thickness M-35 grade with grey cement and pigment complete all as specified and directed by Engineer-in-charge.

M&L for Providing, cement concrete type B1, 1:2:4 (using 20mm graded stone aggregate) as in coping including formwork (straight or curved), ends of interlocking and finishing Complete all as specified and as directed by Engr-in-charge.

M&L for RCC pipes, class NP3, laid in trenches & jointed as specfified for 200 mm bore of pipe including collars complete all as specifed and directed.

M&L for concrete bed in PCC 1:3:6 type C-2 ( using 40 mm graded stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 200 mm bore pipe complete all as specified and directed.

M&L for precast reinforced cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in landings, cover slabs (for manholes etc.), shelves and similar articles with plain faces including necessary form work, set in cement mortar 1:4 complete all as specified and directed. (Note:- Reinforcement shall be measured and paid for separately under respective item of schedule 'A').

M&L for cutting into existing manholes for connecting new drains 225mm dia making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required complete al as specified and directed.

M &L for extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms moulds mitered/stopped in etc complete all as specified and directed .

Dismantling and taking down carefully U/S copper / aluminium point wiring (light, fan, socket, power) complete fitting such as switches, ceiling roses, pendants, lamp holder, light fitting etc including CI/Pressed steel terminals, switch box, and making good the disturbed surface of wall/floor etc, to match with the existing surfaces of wall/floor complete all as specified & directed. Note:- (i) Cost of cutting chases of suitable girth where required on brick /concrete surface and making good disturbed surface shall be deemed to be included in quoted rates. (ii) If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding.

Dismantling and taking down carefully sub-main wiring/service wire of any size including wooden batten etc and making good the disturbed surfaces of wall/floor to match with the existing wall/floor etc complete all as specified & directed. Note:- (i) Cost of cutting chases of suitable girth where required on brick /concrete surface and making good disturbed surface shall be deemed to be included in quoted rates. (ii) If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding. If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding.

Dismantling and taking down carefully existing DB’s any type and making good the disturbed surfaces of wall/floor to match with the existing wall/floor etc. complete all as specified & directed. Note:- (i) Cost of cutting chases of suitable girth where required on brick /concrete surface and making good disturbed surface shall be deemed to be included in quoted rates. (ii) If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding. If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding.

Material & Labour for Point Wiring for one light Point/one fan point/ one call bell point, controlled by one switch with 1100 volts grade single core conforming to (IS:694 /1990) PVC insulated unsheathed 1.5 sqmm multi stranded copper conductor cable (FRLSH) with contineous earth wire of 1.5 Sqmm stranded copper conductor cable (FRLSH) PVC insulated unsheathed , drawn in and including concealed PVC conduit ,duly concealed to wall/floor or above false ceiling with fittings(ISI marked) not less than 20 mm dia (Color coding of wires shall be Phase, neutral and earth wire all as specified ) sunk Metal flush box with and incl decorative polycarbonate frame for housing Modular Switches, sockets , fan regulators etc including white cover cover plate complete all as specified and directed. Note:- (i) Cost of cutting chases of suitable girth where required on brick /concrete surface and making good disturbed surface shall be deemed to be included in quoted rates (ii) If the contractor fail to make good the disturbed surface of wall/floor etc and do not match with the existing surface of wall/floor to the entire satisfaction of Engr-in-Charge a recovery @ of Rs. 50/- per RM will be made from payment due to the Contractor. In case of any dispute the decision of accepting officer will be final and binding.

One 3pin/5pin 5/6 Amps socket out let on same board with other switches , with cables 1.5 sq mm size , complete all as specified and directed.

One 3pin/5pin 5/6 Amps socket out let on independent board with other switches, with cables 1.5 sq mm size, complete all as specified and directed .

All as per item No 175 above but with 2.5 Sqmm PVC insulated FRLSH cable for 15 Amps power point.

S & F Switch Modular single pole, one way 6 Amps, 1 module 240 Volts AC complete all as specified & directed.

Supply and fixing switch modular , one-way 16 Amps, 1 module 240 Volts AC complete all as specified & directed.

Supply and fixing modular socket, 6A -2/3 pin combined 2 module ISI marked 230 volts, 50 Hz complete all as specified & directed.

Supply and fixing modular socket, 6A/16A -2/3 pin combined 2 module 230 volts 50 hz complete all as specified & directed.

Supply and fixing ceiling rose surface bakelite 65x25mm dia having three terminals ISI marked complete all as specified & directed.

Supply and fixing step socket type modular fan regulator 120/280 V , 2 module complete all as specified & directed.

Supply and fixing bell push modular flush type single pole one way 6 Amps, 1 module complete all as specified & directed.

S&F Bell ding dong Type , 240 Volts complete all as specified and directed.

S&F LED wall mounted decorative luminaire suitable for LED lamp 9 /12 watt B-22 base holder and LED lamp complete all as specified and directed.

Supply and fixing batton/angle holder insulated body with back plate, suitable for batten fittings complete all as specified & directed.

Supply and fixing in replacement of LED luminaire 600mm X 600mm, 35/36 watt, 220V AC recessed type with high efficiency PMMA diffuser soft glair free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed.

Supply and fixing in repair energy efficient LED lights fitting, 18 /20 watt , 230 Volt, LED tube light connecting up with with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified & as directed.

Supply and fixing in repair energy efficient LED lights fitting, 10 watt , 230 Volt, LED tube light connecting up with with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified & as directed.

Supply and fixing single pole and neutral enclosure with a two pole and earth plug socket complete with 01 No, RCCB 25 Amp, 30 mili amps, DP, 240 Volts, AC complete all as specified & directed. Note - Cost of cutting chases for enclosure concealed in wall of suitable girth where required on brick /concrete surface and making good disturbed surface shall be deemed to be included in quoted rates.

S & F PVC fresh air fan 240 volts Ac 50 Hz 250 mm sweep PVC body including louvers and cutting as required size and shape complete all as specified & directed.

S & F ceiling fan 1200 sweep 240 volts Ac 50 Hz complete all as specified & directed.

S & F wall mounted fan 400 mm sweep 230 V complete all as specified & directed.

S & F exhaust fan 240 volts Ac 50 Hz 300 mm sweep matellic body (RPM will not be more then 900) including louvers and cutting as required size and shape complete all as specified & directed.

Supply and fixing sheet metal enclosure double door type for MCBs DB SPN(Single pole and neutral) 240V AC 8 way with 200 Amps rated bus bar complete all as specified & directed.

S & F electric water heater storeage type geyser (ISI marked ) 5 star rated inner stainless steel 2 KW of capacity 25 Ltr complete grouting wall with suitable size of nut & bolts washer as required at site with cold water and hot water connection pipe as per required at site complete all as specified & directed.

Supply and fixing MCB SP 5 to 32 Amp 'B' series 10 KA repturing capacity complete all as specified & directed.

Supply and fixing MCB SPN 40 Amp 240 V AC 10 KA repturing capacity complete all as specified & directed.

Supply and fixing sub main wiring two single core 4 sq mm PVC insulated unsheathed multi stranded copper conductor cable ( FRLSH ) 1100Volts grade drawn in & including rigid PVC conduit 20mm dia or more medium grade surface/ concealed in wall as per existing along with 4.00 Sq mm PVC insulated unsheathed copper conductor cable (FRLSH ) as earth wire and wire connected with main earth dolly including cutting chasing and making good disturbed portion complete all as specified & directed. Note:- Two runs of multi stranded copper conductor cable and one run of earth wire including PVC conduit will be measured as a one length.

Material & labour for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground. ( earth pit not less than 2.25 mtr depth below ground level at any type of strata ) with top edge of the earth plate not less than 1.5mtr below normal ground level connected by 4 mm GI wire as earth lead by means of brass nuts and bolt,thimbles check nuts, washers including concrete chamber of PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM 1:4 funnel with wire mesh, RCC pit cover of 320x320x80mm size (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM and charcoal, dust and common salt all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI wire upto 7.5 mtrs long with 15 mm dia light grade Gi pipe protection and watering pipe of GI 20 mm bore, medium grade, including all exavation and earth work and connecting the earthing strip to panel, including testing on completion complete all as specified & directed. Note:- (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick rainforced with XPM weighting not less than 4kg/sqm in lieu of CI cover. (ii) Cost of additional GI wire more than 7.5 mtrs will be measured and paid seperately under relevant items.

Supply and fixing switch piano flush type single pole, one-way 5 Amps, 240 Volts AC

Supply and fixing switch piano flush single pole, one-way 16 Amp, 240 Volts AC

Supply and fixing socket out let 5 Amps flush type all as specified.

Supply and fixing socket out let 5/6pin 5 Amp and 15 Amp flush type (multi) suitable for 240 Volt AC all as specified.

Supply and fixing ceiling rose 3 terminal/PVC/ Polycarbonate, isolated body all as specified

Supply and fixing batton/angle holder insulated bodywith back plate including 09 Watt LED Bulb all as specified

S& F wall mounted LED batten Box type fitting Blu colour end caps pre-wired LED fitting all as per cat part No DMLN 1 LGT 8-16 with & including LED T8 tubular lamp complete all as specified and directed

Supply and fixing sheet metal enclosure double door type for MCBs DB SPN(Single pole and neutral) 240V AC 4 way with 200 Amps rated busbar complete all as specified and directed.

S & F PVC fresh air fan 240 volts Ac 50 Hz 250 mm sweep PVC body including louvers and cutting as required size and shape complete all as directed.

M&L sand cushioning 8 cm below and 15cm above the U/G cable for protection of cable complete all as specified and directed.

Supply and laying fly ash bricks in layers prependicular to the axis of U/G cable for protection of cable complete all as specified and directed.

Supply and laying PVC insulated armoured heavy duty elect cable with STRANDED aluminium conductor 1100 V grade, cross sec area 6 sqmm 2 core and connected with aluminium lugs and properly crimped in trenches/duct.

NOTES :- 1. For the items for which specifications not mentioned any where in the tender, the BIS specifications shall be followed.

Archlife Associates

M/s S.G. BUILDERS