ADDITION ALTERATION TO CUPBOARDS DOORS AND HANDRAILS IN MARRIED ACCOMMODATIONS AT NASA AND CERA SPECIAL REPAIRS TO PATHWAY AND ROVISION OF WALL MOUNTED FAN 10 IN NO AND PROCUREMENT OF 01 IN NO 1.5 TON SPLIT AC FOR MINOR OT AT MI ROOM AT INA EZHIMALA

Amount

Dismantling wrought iron or mild steel work of any description complete all as specified and as directed.

S&F hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts, posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc. flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

All as per item no 2 above but fixing only complete all as specified and as directed.

M&L for preparation of old steel surfaces of any description over 10 cm in width or girth and painting with two coats of anti corossive synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L for preparation of old treated surfaces and applying one coat of santex matt finish paint complete all as specified and as directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard / dense soil complete all as specified and as directed.

M&L for hardcore of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface using broken boulders or stones complete all as specified and as directed.

M&L for cement concrete type D- 2, 1:4:8 (40mm graded aggregate) 100 mm thick as in sub base complete all as specified and as directed.

M&L for 50mm thick cement concrete type B-1, 1:2:4 (20mm graded aggregate) complete all as specified and as directed.

Demolition of cement concrete in ground floors and paving n.exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

M&L for PCC 1:4:8 type D2 (40 mm graded aggregate) as in foundation complete all as specified and as directed.

Dismantling of brick work, PCC block or stone masonry built in cement mortar complete all as specified and as directed.

M&L for laterite stone walling of regular coursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and directed by Engineer-in-charge.

M&L for walling of squared rubble, regular coursed, well bonded, bedded and solidly hearted built in but except stone complete all as specified and as directed.

M&L for chequered cement concrete tiles 250x250x25mm / 300x 300x25mm thick in floors, with mixture of grey cement and pigments, set, jointed and pointed in neat cement slurry over and including 20mm thick screed bed in CM 1:6 complete all as specified and as directed.

Removing excavated material (soil) exc.1.5 km but n exc.5.0 km and depositing where directed complete all as specified and as directed.

Removing building materials etc. to a distance of upto 1.00 km, including loading, unloading and stacking at the destination complete all as specified and as directed.

Taking down chowkats with shutter (without taking off shutter from the frame) exc 1.5 Sqm but n.exc 4.00 Sqm each complete all as specified and as directed.

S&F pressed steel frames of size 105 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges etc complete all as specified and as directed.

M&L for filling concrete inside frame in PCC 1:3:6 type C-0 complete all as specified and as directed.

S&F 30mm thick 1st class hard wood plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, supplied and fitted to chowkats complete all as specified and as directed.

S&F 30mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type both side complete all as specified and as directed.

M&L for preparation of new or previously untreated steel surface exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.

Dismantling cabinets boarding, any description, fixed in any position with screws incl all fittings complete all as specified and as directed.

S&F stainless steel telescopic channel drawers slides complete all as specified and as directed.

S&F stainless steel soft closing hydraulic hinges for shutter complete all as specified and as directed.

S&F prelaminated particle board 18/19 thick exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and as directed.

M&L for preparation of old painted surfaces exc 10cm width or girth and applying one coat of synthetic enamel paint on wooden surfaces complete all as specified and as directed.

M&L for preparation of new or previously untreated wood based surface exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Refixing of shutters of any description exc 1.00 Sqm and n.exc 2.00 Sqm in same opening after easing and adjusting complete all as specified and as directed. Note:- Serviceable shutters obtained from item No.01 above shall be reused.

Resecuring or easing and adjusting without taking down shutters of any description exc 1 sqm and n exc 2 sqm each complete all as specified and as directed.

S&F in repairs continuous (piano) hinges brass bright finish or electrogalvanised, width of flaps (when open) 30 mm complete all as specified and as directed.

S&F in repairs 40mm dia, cupboard knobs fixed with nut, screw and washer of brass, polished complete all as specified and as directed.

S&F in repairs 4 levers brass lock for cupboard, grade 1, size 50 mm complete all as specified and as directed.

S&F 75mm long aluminium handles, cast type, anodised complete all as specified and as directed.

S&F 150mm size extruded aluminium alloy handles fabricated type anodised complete all as specified and as directed.

S&F ball catches with 8mm dia steel ball, brass body and striking plate including letting in and fixed complete all as specified and as directed.

S&F 75 mm size extruded brass handles, fabricated type polished complete all as specified and as directed.

S&F in repairs 100mm stainless steel butt hinges, cold rolled medium weight complete all as specified and as directed.

S&F in repair 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and as directed.

S&F in repairs aluminium alloy wire cloth 0.45mm nominal dia of wire and average width of aperture 1.4mm and fixed with aluminium wire staple complete all as specified and as directed.

S&F in repair 100mm long aluminium, anodised barrel tower bolt of extruded section complete all as specified and as directed.

S&F in repair 150mm long aluminium, anodised barrel tower bolt of extruded section complete all as specified and as directed.

S&F in repairs 100 mm size brass, 4 levers mortise lock, vertical type complete all as specified and as directed.

S&F in repairs floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring and overall length of cover plate 140mm complete all as specified and as directed.

S&F in repair 300mm long ordinary MS rat tail rod pattern springs including roller plate complete all as specified and as directed.

M&L for sub main wiring using 4 runs of 6 sqmm FRLS PVC insulated copper conductor 1100 Volts grade conforming to IS specification drawn through and including PVC conduit/ casing and caping along with 1 run of 6 sq mm PVC insulated copper conductor FRLS cable as earth lead connected to common earth dolly complete all as specified and directed by Engr-in-charge. Note:- (i) Necessary PVC rigid junction boxes for identifying junction as required on site/directed by Engr-in-charge for point wiring work with PVC dummy plates shall deemed to be included in the quoted rate. (ii) Five runs of 6sqmm cable and one run of PVC conduit/casing & caping with necessary accessories will be measured as one unit length. (iii) The wiring shall be done strictly by following proper colour coding using red, yellow and blue for phase, black for neutral and green for earth leads.

M&L for sub main wiring using 2 runs of 4 sqmm FRLS PVC insulated copper conductor 1100 Volts grade conforming to IS specification drawn through and including PVC conduit/ casing and caping along with 1 run of 4 sq mm PVC insulated copper conductor FRLS cable as earth lead connected to common earth dolly complete all as specified and directed by Engr-in-charge. Note:- (i) Necessary PVC rigid junction boxes for identifying junction as required on site/directed by Engr-in-charge for point wiring work with PVC dummy plates shall deemed to be included in the quoted rate. (ii) Three runs of 4sqmm cable and one run of PVC conduit/casing & caping with necessary accessories will be measured as one unit length. (iii) The wiring shall be done strictly by following proper colour coding using red, yellow and blue for phase, black for neutral and green for earth leads.

All as per item No.48 above but 2.5 sqmm FRLS PVC copper conductor complete all as specified and directed by Engr-in-charge. Note:- (i) Necessary PVC rigid junction boxes for identifying junction as required on site/directed by Engr-in-charge for point wiring work with PVC dummy plates shall deemed to be included in the quoted rate. (ii) Three runs of 2.5sqmm cable and one run of PVC conduit/casing & caping with necessary accessories will be measured as one unit length. (iii) The wiring shall be done strictly by following proper colour coding using red, yellow and blue for phase, black for neutral and green for earth leads.

M&L color code point wiring FRLS PVC insulated and unsheathed cable with 1.5 sqmm copper conductor single core multistandred 1100 volt grade conforming to IS 694 drawn through PVC conduit of suitable size, concealed / semi concealed/open suitable size modular metal flush box fitted with modular cover plate with frame (inner/ outer plate) for mounting switches or sockets regulators etc including FRLS 1.5 sqmm earth wire copper insulated wire connected to common earth dolly all as specified for the following:- (a) 5 Amps socket point on independent board Notes:- i. Necessary PVC rigid junction boxes for identifying junction as required on site/directed by Engineer in charge for point wiring work with PVC dummy plates shall deemed to be included in the quoted rate. ii. Same size wire shall be used for phase, neutral and earth conductor. iii. The wiring shall be done strictly by following proper colour coding using red , blue, yellow for phase, black for neutral and green for earth leads.

All as per item no.50 here in above but 2.5 sqmm for 5/15 Amps socket on independent board complete all as specified and as directed.

S&F modular switch one way 16 Amps 1 module complete all as specified and directed by Engineer in charge.

S&F modular socket 6/16 Amps 2/3 pin 2 module complete all as specified and directed by Engineer in charge.

S&F switch socket combination 5 pin 6A/5A with box complete all as specified and directed by Engineer in charge.

S&F wall mounted fan AC single phase 230/ 240 V of size 450 mm sweep, 1330 RPM complete all as specified and directed by Engineer in charge. Make:- Orient 450mm Wall 48 or equivalent in Havells/Bajaj/Usha.

S&F MCB DB SPN 230V double door type 12 way with bus bar of appropriate current carrying capacity, neutral link, earth bar and din rail complete all as specified and directed by Engineer in charge.

S&F MCB single pole 6 to 32 Amps capacity 230 Volts 10 KA C curve complete all as specified and directed by Engineer in charge.

S&F MCB TPN 40 Amps capacity 415 Volts 10 KA C curve complete all as specified and directed by Engineer in charge.

Supply and install 1.5 Ton invertor type split air conditioner units indoor/ outdoor complete with (Non CFC/HCHC) suitable for 230 Volt + 10% , 50 Hz, AC supply complete with cordless remote control unit and with copper condenser with minimum 5 star rating complete all as specified and directed by Engineer in charge. Make:- Mitsubishi Model No MSY-GR18VFTDA1 or equivalent in Carrier/ Daikin. (a) Indoor unit wall mounted blower fan of appropriate capacity including PCB, thermostatic control, air filter and drain for condensing water and suitable foor satnd for indoor unit. (b) Out door unit comprising, Compressor with motor,. air cooled copper condenser with fan and motor unit shall be installed out side the building/ on roof top. (c) Refrigerant copper pipe for suction and discharge line with insulation , condensing water drain pipe & protected by suitable size of flexible PVC conduit with control valves & safety accessories including control wiring for evaporator & condensing unit with suitable size of copper cables as per site requrement ,these all items provided by contractor and no extra cast will pay to contractor. (d) Making good the disturbed surface to match the existing surface after plugging the hole etc. (e) PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in plinth suitable for installation of outdoor unit or powder coated MS bracket fixed on wall/as per Manufacture's instruction with necessary grouting MS hold fast, bolts, washers duly painted and making good to disturbed surfaces suitable for installing outdoor unit complete all as specified and directed. (f) Electrical cable required to connect out door unit and indoor unit to voltage stablizer inclusive in above rate.

Supply and fix voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and of capacity 4 KVA complete all as specified and directed by Engineer in charge.

SANDR

KDR CONSTRUCTION

M/S V ASSOCIATES