SPECIAL REPARING WORKS OF P.S.Q. B-12 AT DHOLERA, DIST:- AHEMEDABAD (INCLUDIN G ELECTRICAL WORKS)(Fourth attempt)(SBD)

NAME OF WORK :- SPECIAL REPARING WORKS OF P.S.Q. B-12 AT DHOLERA, DIST:- AHEMDABAD (INCLUDING ELECTRICAL WORKS)

STATEMENT SHOWING AT APROXIMATE QUANTITY FOR THE ITEM OF ABOVE WORK TO BE CARRIED OUT AND APPROXIMATE COST PUT TO THE TENDER FOR

ITEM NO DESCRIPTION QUANTITY UNIT RATE IN WORD AMOUNT

Dismentaling of tile or stone floor slaid in mortar incl. stacking of servicable material and RS: Forty Seven

disposal of unservicable material with disposing all lead and lift. and Paise Twenty Five

Removing and scrapping of old deteriorated plaster of any thickness from masonry/R.C.C RS: Ninteen and

2 member including stacking of serviceable material and disposal of unserviceable from site of 2732.00 SMT 19.38 Paise Thirty Eight only

work with disposing all lead and lift

Provinding 10 mm thick cement PLASTER in single coat on CEILING for interior plastering and RS: One Hundred

3 finished even and smooth in C.M. 1:3 ( 1 cement : 3 sand ) including finishing with floating coat 111.00 SMT 199.88 Ninty Nine and Paise

of neat cement at Ground Floor. Eighty Eight only

Provinding 10 mm thick cement PLASTER in single coat on CEILING for interior plastering and RS: Two Hundred

finished even and smooth in C.M. 1:3 ( 1 cement : 3 sand ) including finishing with floating coat Twenty Five and Paise

of neat cement at FIRST Floor. Sixty Nine only

Provinding 10 mm thick cement PLASTER in single coat on CEILING for interior plastering and RS: Two Hundred

5 finished even and smooth in C.M. 1:3 ( 1 cement : 3 sand ) including finishing with floating coat 219.00 SMT 251.50 Fifty One and Paise Fifty

of neat cement at SECOND Floor. only

Providing 15mm thick cement plaster in single coat on brick or concrete wall for interior RS: Two Hundred

plastering and finished even and smooth in cement mortar 1:4(1-cement;4-sand) including Three and Paise Thirty

finishing with a floating coat of neat cement slurry at GROUND FLOOR. Four only

Providing 15mm thick cement plaster in single coat on brick or concrete wall for interior RS: Two Hundred

7 plastering and finished even and smooth in cement mortar 1:4(1-cement;4-sand) including 240.00 SMT 231.20 Thirty One and Paise

finishing with a floating coat of neat cement slurry at FIRST FLOOR. Twenty only

Providing 15mm thick cement plaster in single coat on brick or concrete wall for interior RS: Two Hundred

plastering and finished even and smooth in cement mortar 1:4(1-cement;4-sand) including Fifty Nine and Paise Six

finishing with a floating coat of neat cement slurry at SECOND FLOOR. only

Provinding 20 mm thick SAND FACED cement PLASTER on walls above ground level RS: Two Hundred

9 consisting 12 mm thick backing coat of C.M. 1: 3 ( 1 cement : 3 sand ) and 8mm thock finishing 1467.00 SMT 297.68 Ninty Seven and Paise

coat of C.M. 1:1 ( 1 cement : 1 sand ) etc. Complete for any height. Sixty Eight only

Providing CEMENT VATA ( 10cm x 10cm )size quarter round in cement mortar 1 : 1 including RS: Twenty Three

10 neat cement finishing, watering etc. Complete. 77.00 RMT 23.45 and Paise Forty Five

ITEM NO DESCRIPTION QUANTITY UNIT RATE IN WORD AMOUNT

Removing dry or oil bound distemper by a washing and scraping and sand papering the wall RS: Ten and Paise

11 surface smooth including necessary repairs to scratches complete. 3014.00 SMT 10.88 Eighty Eight only

Finishing Ceilling/Slop Surface with Plastic Emulsion Paint on Ceilling/Slop Surface (two coats) RS: One Hundred

to give an required shap even shade after throughly brushing the surface to remove all dirt and Eighty Six and Paise

remains of loose poweder material etc. complete. Rate are inclusive of applying two coat of lapy Seventy Three only

12 (Putty) and one coat of primer on new Ceilling/Slop Surface to give and even shade including 834.00 SMT

thoroughly brushing the surface free from mortar dropping and other foreign matter and sand

papered smooth. Putty,Primer and paint shall be as per approved make list of GSPHCL.

Finishing Wall with Plastic Emulsion Paint on Wall Surface (two coats) to give an required shap RS: One Hundred

even shade after throughly brushing the surface to remove all dirt and remains of loose poweder Seventy Six and Paise

material etc. complete. Rate are inclusive of applying two coat of lapy (Putty) and one coat of Thirty Three only

13 primer on new wall surface to give and even shade including thoroughly brushing the surface 2686.00 SMT

free from mortar dropping and other foreign matter and sand papered smooth. Putty,Primer and

paint shall be as per approved make list of GSPHCL.

Finishing wall with weather proof exterior emulsion paint on wall surface (two coats) over and RS: One Hundred

above applying One Coat Of Primer to give an required shape even shade after thoroughly Forty Seven and Paise

14 brushing the surface to remove all dirt, and remains of loose powdered materials.etc complete. 1555.00 SMT 147.68 Sixty Eight only

primer and paint make as per the approved list of GSPHCL

Providing & Fixing to wall, ceiling, floor (consealed pipe includingmaking grooveof required size RS: Four Hundred

&after fixing the pipe the groove shall be filled up with C.M1:3 aftertesting of joints) CPVC pipes Thirty Seven and Paise

SDR-13.5 I mark of following nominal bore tube ,fiitings &clamps with as required fitting such as Sixty Six only

reducing coupler ,union, band,plug,end cap,pipe clip,tee, hex nippel, elbow, coupler etc complet

with using bonding materials rates are including of making good the wall,ceiling & floor etc

complete . (Excavation of earth in trenchies & filling will be paid separatly where ever required )

40 mm inside dia.

Providing & Fixing to wall, ceiling, floor (consealed pipe includingmaking grooveof required size RS: Three Hundred

&after fixing the pipe the groove shall be filled up with C.M1:3 aftertesting of joints) CPVC pipes Thirty and Paise Thirty

SDR-13.5 I mark of following nominal bore tube ,fiitings &clamps with as required fitting such as Six only

reducing coupler ,union, band,plug,end cap,pipe clip,tee, hex nippel, elbow, coupler etc complet

with using bonding materials rates are including of making good the wall,ceiling & floor etc

complete . (Excavation of earth in trenchies & filling will be paid separatly where ever required )

32 mm inside dia.

ITEM NO DESCRIPTION QUANTITY UNIT RATE IN WORD AMOUNT

Construction of BRICK MASONRY CHAMBER for under Ground C.I. inspection chamber and RS: Three Thousand

bends with bricks having crushing strength not less than 35 Kg / Cm2 in Cement Mortar (1:5) Seven Hundred Ninty

with RCC top slab with CC (1:2:4) mix ( 1 cement : 2 corse sand : 4 gradded aggregate 20 mm Three and Paise

nominal size) with 8mm. dia. TMT steel at 15 cm. c/c both ways & providing and fixing precast Eighteen only

r.c.c cover size .60 x .45 x .07 mt. with angle frame fixed with C.C (1:2:4) Foundation concrete

1:5:10, inside plaster 15 mm thick with C:M (1:3) finished smooth with a floating coat of neat

cement slurry on walls & bedconcrete etc, complete. Inside dimension of chamber 455 mm x

610 mm x 450 mm deep for match proposed pipe line. Rate are also inclusive of out side plaster

15mm. th. in c:m 1:3 from top of the chamber & all side up to 15 mm. deep below ground level.

Including Providing & Fixing Precast RCC Frame with Cover MD 10 Ton ( Rubber Mould Finish

) Inner size 600 x 450 mm with All Necessary Fittings.

Extra rate for constructing chamber for every additional depth of 0.1 m or part there of FOR RS: Two Hundred

18 455MM X 610MM 12.00 NO 239.99 Thirty Nine and Paise

Ninty Nine only

Providing, supplying and fixing Corrugated DWC HDPE Pipes of Class SN8 Structured Wall RS: Three Hundred

polyethelene Piping systems (Pipe with online/offline coupler and elastomeric sealing ring) with Ninty Six only

non-smooth External Annular Corrugated and Smooth Internal Surfaces (Double Wall) for non-

pressure underground Sewerage & Drainage application as per EN:13476-3 including all local

and central taxes, transportation, freight charges, octroi, inspection charges, loading, unloading,

conveyance to the departmental stores etc. complete. (150 mm ID Dia) Including Lowering,

laying and jointing of class SN 8 structured wall ( External Annular Corrugated & Smooth Internal

19 surface) Polyethylene Piping and fittings with the help of coupler ( on line / off line ) attached 58.00 RMT

with one end of pipes, sliding over the elastomeric sealing rubber ring placed on the specified

valley of the corrugation at the spigot end, lowering the same into the trench, laying on the lower

bedding (constructed at bottom of trenches) at prescribed gradient,depth & alignment ,testing

the water tightness of the joints, ensuring the continuity tests of specified pipe segments etc.

complete as per drawing,specifications & detailed engineering, including carriage of pipes &

fittings from site stacks to the place of laying etc. as per direction of Engineer-in-charge.

Providing, supplying and Fixing Corrugated DWC HDPE Pipes of Class SN8 Structured Wall RS: Two Hundred

polyethelene Piping systems (Pipe with online/offline coupler and elastomeric sealing ring) with Twenty Nine only

non-smooth External Annular Corrugated and Smooth Internal Surfaces (Double Wall) for non-

pressure underground Sewerage & Drainage application as per EN:13476-3 including all local

and central taxes, transportation, freight charges, octroi, inspection charges, loading, unloading,

conveyance to the departmental stores etc. complete. (100mm ID Dia) Including Lowering,

laying and jointing of class SN 8 structured wall ( External Annular Corrugated & Smooth Internal

surface) Polyethylene Piping and fittings with the help of coupler ( on line / off line ) attached

20 with one end of pipes, sliding over the elastomeric sealing rubber ring placed on the specified 38.00 RMT

valley of the corrugation at the spigot end, lowering the same into the trench, laying on the lower

bedding (constructed at bottom of trenches) at prescribed gradient,depth & alignment ,testing

the water tightness of the joints, ensuring the continuity tests of specified pipe segments etc.

complete as per drawing,specifications & detailed engineering, including carriage of pipes &

fittings from site stacks to the place of laying etc. as per direction of Engineer-in-charge.

ITEM NO DESCRIPTION QUANTITY UNIT RATE IN WORD AMOUNT

Providing & Laying ( to level or slopes ) and jointing reinforce concrete non pressure pipes I.S. RS: Three Hundred

class NP 2 of the following internal diameter with collars & butt ends prepaid for collar joints Forty Four and Paise

including testin of joints. 250 mm dia pipe Fifty Nine only

Providing & fixing to wall ceiling & floor 4kg/cm2 working pressure pvc pipe of 90mm dia high RS: Three Hundred

density complete with specials flanges compressor type fittings wall clips on wooden patti Twenty Three and Paise

22 including making good the wall ceiling & floor on the terrace rain water pipe shall be of 90mm dia 95.00 RMT 323.15 Fifteen only

PVC horizontal pipe and bend of PVC at Terrace lvl & shoe bend at the end near by ground Lvl.

Providing and fixing to wall, ceiling and floor SWR/UPVC soil waste pipe 75 mm dia. Of RS: Two Hundred

ISI13592/92 . Rate inclusive of all fittings like single or double 'Y' with door, reducer, coupler Sixty Four and Paise

23 single T with door bend, pipe clip on wooden patti etc. complete and making good the wall, 104.00 RMT 264.97 Ninty Seven only

ceiling and Floor.

Providing and fixing to wall, ceiling and floor SWR/UPVC soil waste pipe 110 mm dia. Of RS: Four Hundred

ISI13592/92 . Rate inclusive of all fittings like single or double 'Y' with door, reducer, coupler Ninty Five and Paise

single T with door bend, pipe clip on wooden patti etc. complete and making good the wall, Ninty One only

ceiling and Floor.

Providing and fixing S.W. Gully trap with C.I. grating brick masonry chamber & water-tight C.I. RS: One Thousand

cover with frame of 300mm x 300mm size (inside) with standard weight. [I] Square mouth trap One Hundred Seventy Six

(B) 150mm x 100mm size P or R type. and Paise Ninty Four

Providing & Fixing PVC Multi nahni trap- 100 mm dia. With SS jali of the following nominal RS: One Thousand

diameter of self cleansing design with all necessary fittings etc complete as per direction of One Hundred Twenty

Engineer in charge. Including with Providing and fixing floor drain jali (Glossy Finish) (On N.T. or Two and Paise Twenty

26 Multi trap) of 6" X 6" size made of stainless steel Grade 304 floor drain 3 piece 12.00 NO 1122.26 Six only

(Cover/jali/Grating) with anti cockroach bowl on N.T. or Multitrap. Rate are inclusive of all

necessary fittings, material, labour etc. complete as per direction of engineer in charge.

Provinding and fixing in position SWR/UPVC COWEL VENT to pipe 75 mm dia directed. RS: Sixteen and

27 8.00 NO 16.47 Paise Forty Seven only

Provinding and fixing in position SWR/UPVC COWEL VENT to pipe 110 mm dia directed. RS: Twenty Eight

28 4.00 NO 28.16 and Paise Sixteen only

Provinding and fixing gun metal check or non return full way WHEEL / HANDLE VALVE Rate RS: Six Hundred

are inclusive of all materials,Labour & Necessary Fittings etc. Complete as per Detailed Fifty Six and Paise

29 Drawings, Specifications and as per the Instruction of Engineer In 5.00 NO 656.85 Eighty Five only

charge. All material used as per approved make list by GSPHCL. (40 mm inside dia).

Provinding and fixing gun metal check or non return full way WHEEL / HANDLE VALVE Rate RS: Three Hundred

are inclusive of all materials,Labour & Necessary Fittings etc. Complete as per Detailed Eleven and Paise Sixty

Drawings, Specifications and as per the Instruction of Engineer In Seven only

charge. All material used as per approved make list by GSPHCL.(32 mm inside dia).

Dismantling sanitary fitting like wash basin, wc pan, indian and european type, flushing tanks RS: Four Hundred

31 etc. incl. stacking the materials with disposing all lead and lift. 6.00 NO 401.63 One and Paise Sixty

ITEM NO DESCRIPTION QUANTITY UNIT RATE IN WORD AMOUNT

Providing and fixing water closet, squatting pan (Orrisa Type W.C. pan) size 580 mm. x 440 RS: One Thousand

mm. first quality including necessary 'P' or 'S' trap, including jointing the trap with pan and soil Three Hundred Twenty

32 pipe in vitreous china, white colour. 6.00 NO 1321.52 One and Paise Fifty Two

Provinding 10 mm thick cement PLASTER in single coat of interior plastering and finished even RS: Two Hundred

and smooth in cement mortar 1:3 ( 1 cement : 3 sand ) and finishing with floating coat of neat Ten and Paise Ninty

33 cement slurry including providing and mixing WATER PROOFING material in C.M in proportion 74.00 SMT 210.99 Nine only

recomended by the manufacturer including finishing with a flaoting coat of neat cement slurry.

Providing & laying acrylic based (Zycosil or equivalent) water proofing paint treatment in two RS: One Hundred

coats of vertical and horizontal surface of depressed portion of bath/wc as directed by engineer Ten and Paise Seventy

incharge.this treatment shall be carried out over & above water proofing plaster. only

Providing & laying WHITE/COLOUR GLAZED TITLES 6mm thick in FLOORING. Treads of RS: Nine Hundred

35 steps & landing laid on a bed of 12 mm thick C.M. 1:3 ( 1cement : 3 coarse sand )finished with 10.00 SMT 908.17 Eight and Paise

flush pointing in white cement. Seventeen only

Provinding & laying WHITE/COLOUR GLAZED TILES 6 mm thick in skirting, risers of steps and RS: One Thousand

DADO on 10mm thick cement plaster 1: 3 ( 1 cement : 3 coarse sand ) & jointed with white Ten Hundred Forty Four

36 cement slurry. 60.00 SMT 1044.23 and Paise Twenty Three

Providing and laying 25mm thick DIAMOND POLISHED KOTA STONE SLAB FLOORING over RS: One Thousand

20mm average thick base of cement mortar 1:6 ( 1 cement : 6 coarse sand) laid over & jointed Ten Hundred Eighty One

with grey cement slurry including rubbing & polishing etc. Complete. and Paise Ninty only

Providing and laying DIAMOND POLISHED KOTA STONE SLAB in RISERS of steps, dedo , RS: One Thousand

skirting and pilllars laid to 10 mm thick cement mortar 1:3 ( 1 cement : 3 coarse sand) & jointed Two Hundred Seventy

with grey cement slurry including rubbing & polishing etc. Five and Paise Ten only

Providing and laying 24" x 24" Double Charge vitrified 8 to 10 mm thick tile flooring over 20 mm RS: One Thousand

(average) base of cement mortar 1:6 ( 1 cement: 6 coarse sand) on new surface or fixing on Ten Hundred Sixty Two

existing flooring by adhesive including dismantling of existing flooring and material jointed with and Paise Fifty only

colour cement slurry including finished with flush pointing & cleaning the surface etc. complete

for all Floors. Material shall be used as per approved make list by GSPHCL.

Providing and laying 24" x 24" Double Charge vitrified 8 to 10 mm thick tile for skirting,risers of RS: One Thousand

steps and dedo over 20 mm (average) base of cement mortar 1:3 ( 1 cement: 3 coarse sand) One Hundred Thirty and

on new surface or fixing on existing flooring by adhesive including dismantling of existing flooring Paise Fifteen only

and material jointed with color cement slurry including finished with flush pointing & cleaning the

surface etc. complete for all Floors. Material shall be used as per approved make list by

Providing and fixing brass screw down BIB tap POLISHED BRIGHT 15 mm dia. RS: One Hundred

41 12.00 NO 184.98 Eighty Four and Paise

Ninty Eight only

ITEM NO DESCRIPTION QUANTITY UNIT RATE IN WORD AMOUNT

Providing, Fabrication and fixing M.S. Grill / GATE of approved pattern fabricated from M.S. flat, RS: Seventy Four

Square Bars, round bars, C channel, square/round box pipe as per detail drawings. Rate is and Paise Ninty Two

inclusive of welding with grinding and applying of mild steel putty with hardener into groove to only

have smooth surface, two coats of oil paint and one coat of yellow zinc chromate primer coat of

42 approved brand only. Oil paint shall be luxol Enamel paint of Berger Paint India Limited or Asian 166.00 KG

paint Apcolite premium gloss Enamel of Asian Paint or Dulux premium gloss Enamel of Dulux

Paint and Nerolac Sythetics Enamel of Nerolac paint for all floor and at any height only. (M.S.

Grill / GATE material should be ISI mark Only)

Painting two coats (excluding priming coat) on new wood and wood based surface with RS: Eighty Seven

43 enamel paint, interior to give an even shade including cleaning the surface of all dirt, dust and 231.00 SMT 87.26 and Paise Twenty Six

other foreign matter sand papering and stopping. only

Provinding and laying inegrated cement based water proofing treatment of required thickness RS: Eight Hundred

over the roof including 10mm thick waterproofing cement plaster in cement plaster in cement Fifty Five and Paise

mortar1:3 and chaina mosaic fitting and finally finishing the surfase with white cement slurry and Eleven only

slopping out taerrace slabs with following specification laid to required slope not flatter than 1:80

( the thickness of water proofing treatment near rainwater outlet or the lowest point of the

44 finishedslope shall not be less then 45mm, including treating the vertical surfaseof the parapet 341.00 SMT

wall up to 20cms . height above finished level of terracing including finishing the top with joint

less water proofing plaster , curing , testing etc. complete. Rate is including ten years

performance of guarantee bond to be given on stamp paper. (No extra shall be paid for increase

in thickness for proper slope).

(A) Applying and grouting a slurry coat of neat cemnt using 2.75 kg/sqm. of cement admixed with

properly water proofing compound conforming to IS -2645 and 10 mm thick water proofing

cement plaster in Cement mortar 1:3 over the R.C.C.slab incl. cleaning the surface before

(B) Layign cement corcretre using broken brick bats 25mm to 40mm size with 50% of cement

mortar 1:4 (1cement :4 coarse sand ) over 10mm thick water proofing cement plaster in cement

mortar 1:3 (1 cement ,3 coarse sand) admixed with proprietary water proofing compound

conforming to IS 2645 to required slope and treating similarly the adjoining walls up to 200mm

height incl. rouding of junction of walls. C) After Two Days of proper curing applying a second

floor of cement slurry

(D) Finishing the surface with china mosaic pieces laid on 10mm thick joint less cement plaster

of mix 1:3(1 cement :3 coarse sand )admixed with proprietary water proofing compound

conforming to IS :2645 and finally finishing the surface with trowel with neat cement slurry

(E) The whole terrace so finished shall be flooded with water for a minimum period of two weeks

for curring for final taste

All above operation to be done in order and as directed and specified by the Engineer In

Excavation for foundation in loose or soft soil upto 1.5 m. depth including sorting out and RS: One Hundred

45 stacking of useful materials and disposing of the excavated stuff upto 50M Lead. 27.00 CMT 115.92 Fifteen and Paise Ninty

Dismantling C.I. pipes, GSW pipe, AC rain water pipe, PVC Pipe with fitting and clamps incl. RS: Seventy Four

46 stacking the materials with all lead and lift (for any dia. Of pipe) 514.60 RMT 74.03 and Paise Three only

ITEM NO DESCRIPTION QUANTITY UNIT RATE IN WORD AMOUNT

Providing and laying cement concrete flooring 1:2:4 (1- cement : 2- sand : 4- M/C graded stone RS: Three Hundred

47 aggregates 20 mm. nominal size) laid in one layer finished with a floting coat of neat cement: (B) 120.00 SMT 348.08 Forty Eight and Paise

50mm thick. Eight only

RS: Four Hundred

FILLING in plinth with SAND under floors including watering, raming consolidating and dressing

48 12.00 CMT 455.63 Fifty Five and Paise Sixty

Providing & laying plain cement CONCRETE 1:5:10 (1-cement : 5-coarse sand : 10-Brick Bat 40 RS: Two Thousand

mm NOminal size) and curing etc. complete excluding cost of formwork in FOUNDATION & Four Hundred Ninty Two

49 PLINTH. 12.00 CMT 2492.51 and Paise Fifty One only

Bricks work using comman burnt clay building bricks having crushing strenth NOt less than 35 RS: Three Thousand

kg/cm2 in foundation & plinth in cement mortar 1:6 ( 1 cement : 6 coarse sand ) ( coventional Nine Hundred Eighty One

50 bricks ) 13.32 CMT 3981.21 and Paise Twenty One

51A Providing & erecting Point wiring with approved ISI mark 2 x 1.5 mm2 copper FRLS PVC 160.00 Point 291.00 RS: Two Hundred

insulated wire with 1.5 mm2 copper FRLS PVC insulated wire for earth continuity in Ninty One only

existing pipe erected Open wall/ceiling complete and accessories erected flushed on

wall/ceiling complete with 6 Amp. Tissino type ISI marked flush type Switch/ Bell push white

shock proof accessories erected on polished wooden block covered with 3 mm. thick white ISI

laminated sheet with necessary Lamp holder/ceiling rose / H.D.Connector as directed. .Length

of point wiring must not increase than 10 mtr for that necessary switch board & their Location

must be finallised before execution by agency other wise payment will not be done for extra long

Point. For Open Wiring (a) Light point cat ii (conductor resistence should be as per

IS:8130/1984 ) ( Wire must be having box packing)

51B For Fan Point 37.00 Point 291.00 RS: Two Hundred

51C For separate Point (with 6 Amp. Switch & 3/5 pin socket both having ISI mark) 48.00 Point 259.00 RS: Two Hundred

Fifty Nine only

51D For Looped on switch board (with 6 Amp. Switch & 3/5 pin socket both having ISI mark) 100.00 Point 66.00 RS: Sixty Six

51E For Bell Point. 12.00 Point 291.00 RS: Two Hundred

52 Providing & erecting Electronic Hum Free 5 Pin socket type Step Fan Regulator (ISI make) (The 37.00 Each 217.00 RS: Two Hundred

regulator should be used same as company of accessories used) Seventeen only

ITEM NO DESCRIPTION QUANTITY UNIT RATE IN WORD AMOUNT

53 Plug Point wiring with approved ISI make 2 x 2.5 sq.mm copper PVC insulated FRLS wire with 36.00 Each 489.00 RS: Four Hundred

1.5 sq.mm (green) copper PVC insulated FRLS wire for earth continuity in FIA approved ISI Eighty Nine only

mark medium class White colour 20 mm dia. embossed rigid PVC pipe with PVC fitting fixed

with adhesive solution erected on wall / slab along with continuous G. I. fish wire to draw wires

and laid in approved manner. with 16 Amp ISI marked flush Tissino type I type switch / Socket

and accessories erected on polished wooden box covered with 3 mm thick white ISI mark

laminated sheet. (a) 16 A switch & 1 No. 6/16 A universal socket combined white colour

suitable for 3 pin top duly. (Approved ISI make & model) both having ISI mark. cat ii

54A Providing and erecting 1.5 mm thick FIA approved and ISI mark White colour (embossed) RIGID 1100.00 Mtr. 24.00 RS: Twenty Four

PVC PIPES of following size complete erected with necessary PVC fittings & Junction boxes only

fixed with adhesive solution. concealed in wall / slab along with contineous fish wire to draw

mains, laid in approved manner with plastering by cement mortar & finishing the surface to

match the wall / ceiling. For 20 mm dia.

54B For 25 mm dia. 50.00 Mtr 33.00 RS: Thirty Three

55A Providing & erecting Main with FRLS PVC Insulated wire with FIA approved ISI mark medium 700.00 Mtr. 46.00 RS: Forty Six

class white colour 20/25 mm dia. embossed rigid PVC pipe with PVC fitting fixed with adhesive only

solution erected in wall / slab along with contineous G. I. fish wire to draw mains laid in

approved manner with plastering by cement mortar & finishing the surface to match the wall /

ceiling complete with FRLS PVC insulated wire for earth continuity. (Approved ISI make only)

(conductor resistence should be as per IS:8130/1984 Class II as per attathed annexure CR) 2 x

1.5 sq.mm. FRLS copper multi stranded conductor mains with 1.5 sq.mm. FRLS copper multi stranded

conductor earthing.

55B 2 x 4.0 sq.mm. FRLS copper multi stranded conductor mains with 2.5 sq.mm. FRLS copper 350.00 Mtr. 86.00 RS: Eighty Six

multi stranded conductor earthing. only

56 Providing & fixing 20 mm. dia PVC insulated GI corrugated flexible pipe with necessary 15.00 Mtr. 31.00 RS: Thirty One

socket, PVC bushes Saddle. only

ITEM NO DESCRIPTION QUANTITY UNIT RATE IN WORD AMOUNT

57 Providing ad erecting approved make single phase Single Door metal clad D.B. as per relevant 12.00 Each 4287.00 RS: Four Thousand

indian standards ammended upto date. Supplying and fixing following way single phase MCB Two Hundred Eighty

distrubution board of company fabricated with sheet box with powder coated inside and outside Seven only

after apply seven tank chemical process of MCBDB Door, Back side & Body must be made of

1.2 mm thick CRCA sheet cover complete with suitable integral single piece construction tinned

copper busbar and link with all necessary interconnection and with necessary size MS frame for

mounting MCBDB. Manufacturer must be provided (1) IP 43 and as per IS:8623-1 & 3, IEC

61439-1 & 3 having D type PU gasket. (2) Seven tank Powder coating Certificate (3) Tinned

Copper/Brass make neutral & Earthing link with isolation & Protecting Cover for 240 Volts on

surface / recess complete with loose wire box, terminal connectors for all incoming and outgoing

circuits, with suitable size FRLS PVC insulated copper conductor up to terminal blocks and

internal connection, tinned coppper bus bar, 1 no. tinned copper neutral link, tinned copper earth

bar, din bar, detachable gland plate, interconnections, powder painted including earthing

etc.Single phase incoming and horizontal single phase outgoing. For 12 Way MCBDB: Including

40 Amp. 30 mA double pole ELCB (ELCB confirming to IS:12640/1988 having sensitivity of

mA and breaking capacity of 10 KA) 01 Nos &, MCB 40 Amp. double pole switch (C curve

confirms to IS:8828 having breaking capacity of 10 KA) 01 Nos and S.P. MCB of rating 6 to

Amp. with NL suitable to operate on 240 Volt A.C. power. (6 Amp:- 4 Nos., 16 Amp:- 4 Nos. )

58 Providing and erecting 240 volt MCB double pole switch for motor inductive load(C Curve) having 13.00 Each 599.00 RS: Five Hundred

10 KA Breaking capacity and confirms to IS : 8828 with same company Metal box with earthing Ninty Nine only

terminal having following capacity. with necessary quarter Numbering with oil paint by Painter.

(a) 40 Amp Capacity.

59 Supplying & erecting 12 mm thick backelite sheet of approved make and grade on 25 x 25 x 3 3.50 Sq.Mtr. 2289.00 RS: Two Thousand

mm red oxide painted angle iron frame suitable for fixing ICDP SWITCH and energy meter Two Hundred Eighty Nine

(contractor shall make approved drawing of Bakelite sheet To arrange required No. of Energy only

meter & ICDP switch -busbar etc. as per Actual space available in electrical room at site)

60 Providing & Erecting PVC Perforated trunking Channel of Size 45mm X 45mm with required size 10.00 Mtr 128.00 RS: One Hundred

of screw as directed by EIC ( Make: Precision/Premium or Equivalent make approved by EIC ) Twenty Eight only

61A Providing & Erecting 2.0 mtr long Earthing system by making minimum bore of 225 mm dia in soft soil. 4.00 Each 7025.00 RS: Seven Thousand

Suitable for doing pipe-in-pipe technology earthing. Earthing electric rod must be made from Corrosion free Hot Twenty Five only

dip galvanizing pipes having following specification.

(A)(A) Earthing Electrode: outer pipe :- 88mm minimum O.D ,ISI 'B ' Class ISI mark of Reputed Brand, Inner

pipe:- 42 mm minimum O.D, Pipe B Class ISI mark reputed Brand Terminal Size: 70mm X 100mm length,

Terminal Should be made from inner pipe for that pipe must be pressed and gave rectangular shape so its

work as a terminal. The hot deep galvanising must be done after above process. Galvanised thickness must be

minimum 75 micron any where. SS Nut bolt:- 2 no. with washer suitable for 14mm dia. hole must be provided

at terminal. total minimum Weight(approx.) of earth electrode with inside conductive material minimum should

(B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm/ meter testing as per IEC 62561-2017, Voltage

drop:- < 1 volt at no load & dry form, Sulphar content:- <2%

(C) Back fill Compound :- Earthing compound should be capable to retain moisture for long time Back Filling

Compound weight is 25 Kg. Necessary test report must be submitted.

(D) Chamber and cover :- Earthing chamber should be size of 400mmX400mmX400mm depth and Cover

should be heavy duty cast iron with required size of 300mmX300mmX4mm thick.

ITEM NO DESCRIPTION QUANTITY UNIT RATE IN WORD AMOUNT

Necessary test report must be submitted. 1. Short

circuit test by ERDA/ CPRI for 25KA

2. Resistivity test of conducting material from NABL accredited lab.

3. Hot dip galvanised / zinc coating micro test from reputed laboratory.

4. General test report from OEM regarding specification of earthing.

{Make to be approved by EIC} (Strictly subject to item specification only) OEM has to submit all detail &

sample for approved before supplying

Water must be poured in bore before starting earthing. Earthing value must be measured with earth tester.

Agency has to bring the earth resistance to at least 02 ohms & voltage between neutral & Earthing upto

volt. Agency has to maintain earthing & its value for one year. If required. Earthing must be done in the

presence of A.E (GSPHCL)

61B For above earthing additional charges for boring in hard rock soil (by breaker) & filling soft 4.00 Each 276.00 RS: Two Hundred

soil in earth pit (certificate for soil have to given by DEE / AE along with photographs) Seventy Six only

62A Providing & Erecting Mains with ISI marked, 1.1KV grade electrolyte multi stranded, 75.00 Mtr. 56.00 RS: Fifty Six

annealed copper conductor with heat resistant PVC insulated conforms to IS 694, IEC - 227 only

erected in existing pipe of following size (Specifically for control panel, relays, power

switchgears, motor starters & control wiring) with required size of copper lugs, nuts and bolts if

required. Conductor resistance should be as per IS:8130/1984 class II as per attached annexure-

CR.For One wire 6.00 sq. mm ( Meter Interconnection)

62B For One wire 16.00 Sq mm 30.00 Mtr. 141.00 RS: One Hundred

63 Supplying and erecting 8 W LED lamps with following wattage capacity of 220 to 90.00 Each 111.00 RS: One Hundred

240 voltage, minimum 15000 burning hours life, 500 V in built-surge Eleven only

protection,Polycarbonate diffuser, mounting suitable for E14 / E27 / B22 lamp

holders, pf >= 0.5 (A) LED Lamps integral type, with PC diffuser suitable LAMP

64 Supplying and erecting 3 W LED lamps with following wattage capacity of 220 to 240 voltage, 24.00 Each 69.00 RS: Sixty Nine

minimum 15000 burning hours life, 500 V in built-surge protection,Polycarbonate diffuser, only

mounting suitable for E14 / E27 / B22 lamp holders, pf >= 0.5 (A) LED Lamps integral type, with

PC diffuser suitable LAMP holder

65 Providing and erecting Polycarbonet body surface mounting LED Bulk head type 9 watt 3.00 Each 780.00 RS: Seven Hundred

Lighting Fitting with electronic driver having THD < 15%, CRI>80, P.F.0.95 And lumen output Eighty only

from luminaire 720 lm, input voltage range 160-270 V AC, 50 Hz cool white (3000 to 6500 k),

inbuilt driver having efficiency >=80lm/w, -20 deg C to + 60 deg C working temperature, AL

frame with Beam Angle 120 deg.

ITEM NO DESCRIPTION QUANTITY UNIT RATE IN WORD AMOUNT

66 Supplying and Erecting LED indoor fitting of approximately 4feet long with LED of wattage 0.2W 45.00 Each 370.00 RS: Three Hundred

to 0.5W assemble on single MCPCB with housing use as a heat sink shall be made from Seventy only

Aluminum extrusion having enough strength (sample must be approved by EIC) with

polycarbonate diffuser with following specification:(A)Company mark/name on the fitting.(B)

Rated input voltage and frequency: 220V to 240 VAC ; 50Hz. (c)Rated input wattage: max.

24w (d)Rated input current : 0.2 Amp (e) Power Factor : Min. 0.90 (f) ATHD : Max. 15%

(g)Rated Luminous flux: Min. 2420 lm (h) CCT: 6500K (i) CRI: Min. 80Ra

(j) Driver Efficiency: Min. 80% (k)LED life span: Min. 50000 Hrs @ L70 (L) Over Voltage

protection: Withstand up to 440V/AC for 4 Hrs. (m) Surge protection : Min. 2KV (n) IP rating: IP

20 (m) IK rating : IK 02 (n) Short circuit , Open circuit & Reverse Polarity Protection must be

provided (o) Fixing clamp design & strength should be sufficient to hold the fitting erected on

wall or ceiling. (P) 3 core copper wire of appropriate size with earthing connector (Note:-The

manufacturer/ authorized Channel partner of the manufacturer has to submit 5 yrs free

replacement Guarantee for complete Fixture) [Approval will be given strictly subject to item

67 Providing, erecting, testing Ceiling Fan confirming to IS: 374/1979 AMDT No. 1 to 6 Class-I, 50 25.00 Each 1929.00 RS: One Thousand

Hz. Specification of Ceiling Fan must be as per below. (1) Sweep: 1200 mm, (2) Operating Nine Hundred Twenty

Voltage: 180 to 230 V, (3) Power Factor: > 0.9, (4) Power Consumption: maximum 53W, (5) Nine only

RPM: minimum 330, (6) Service value:min 4.3 m3/min. (7) Class of insulation: 'B', (8) No. of

heavy duty premium quality Ball bearing: Two, (9) Total Body: Top & Bottom should be

alluminium, (10) Blade: Aluminium approx 1.1 mm thick, (11) Colour: White high grade powder

coating, (12) Canopy: Two Nos. Heavy duty, (13) Condenser: min 1.5 MFD (15% Tolerance )as

per is 1709-1984, Aluminium body premium quality, Branded make,(14) Down road: up to

mtr as per site requirment, (15) Required fixing accessories, (16) 3 core 0.75 sq.mm ISI wire as

per site requirment, (17) No vibration and noise due to mechanical parts. (Agency has to erect

safey wire with ceiling fan and checked with EIC) (OEM has to approved model as per tender

specification and tested at ERDA) (Necessary test reports should be submitted strictly at the

time of approval. Sample approved by EIC subject to above specification only)

68 Providing Fan clamp of 30 x 5 mm flat of required length & 10 mm M.S. Bolt & Nuts erected 20.00 Each 98.00 RS: Ninty Eight

with necessary hook of 10 mm M.S. Round Bar. only

69 Providing and erecting Decorative Ding Dong call bell Stereo type 250 Volt complete erected on 12.00 Each 170.00 RS: One Hundred

existing polished wooden block or in M.S. box with 3 mm thick white ISI mark laminated sheet. (Anchor Seventy only

(chime), Vision, Rider make)

70 Providing, erecting, fabricating the M.S. structure as per requirement of site as per structure 20.00 Kg 74.92 RS: Seventy Four

design Including proper size approved by EIC of M.S. angles, flats, bars, square pipe, and Paise Ninty Two

channels, sections (Tata,Zindal,Asian,Jsi Make) complete with cutting, welding, grinding and only

finishing duly painted with Asian/Nerolac make premium quality oil paint and true care red oxide

metal primer,asian paint make with erection on site as per direction of engineer in charge with

necessary grouting cementing, plastering and finishing complete. All hole opening of square

pipe end must be closed with M.S plate welding. Payment will be done on KG as per Actual

ITEM NO DESCRIPTION QUANTITY UNIT RATE IN WORD AMOUNT

71 Providing & fixing Solderless crimping type Aluminium lugs conforming to IS suitable for cable of 8.00 Each 15.00 RS: Fifteen only

following size evenly crimped with high pressure tool & connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved manner. For 16/25 Sq.mm. Allumium Cable

72 SITC of Outdoor aesthetically designed LED Street Light Luminaire with total consumption of 8.00 Each 3512.00 RS: Three Thousand

Max. 45 W with single piece die cast aluminium housing, high power LED shall be mounted on Five Hundred Twelve

high quality metal core PCB with extremely precison designed heat sink complete with IP66 only

protection Class with polycarbonate / thoughened glass cover the fixture should be suitable for

pole/bracket mounting. The fixture to comply both LM79 and LM 80 guidelines with LED module

min. 130 lumen/watt with toughen Glass L70 at 50,000 hrs, provided with high quality

polycarbonate lenses for better light distribution. The watt capacity of Each LED must be >=4W

in street light fitting. The Fixture Should be able to be Pole Mounted and also bracket mounted,

provided with high quality driver for protection against high and low Voltage cut Off, opertional

for high amibient and high humid envirnoments, THD of driver should be less than 10% and P.F

> 0.95. Also the Fixture should meet the following technical criterias Oprating range Voltage

to 270 V, system efficiency >= 110 lm/w, and total lumens not less then 4950, CCT > 5000K,

CRI > 65, beam angle 120 deg, surge immunity level at least 4 KV integral and 10 KV non

integral (Note:- The manufacturer / authorized Channel partner of the manufacturer has to

submit 5yrs free replcement Guarantee for complete Fixture)

73 SITC of Outdoor aesthetically designed LED Flood Light Luminaire with total consumption of 6.00 Each 6228.00 RS: Six Thousand

maximum 90 W with single piece die cast aluminium housing, LED's mounted on high quality Two Hundred Twenty

metal core based PCB with extremely precison designed heat sink, complete with IP66 Eight only

protection Class, with polycarbonate / Toughened glass cover. The fixture should be suitable for

pole/bracket mounting. The fixture to comply both LM79 and LM 80 guidelines with LED

minimum 110 lumen/watt with L70 at 50,000 hrs, provided with high quality polycarbonate

Seperate lenses for better light distribution. The watt capacity of Each LED must be >=4W in

Flood light fitting. The Fixture Should be able to be Pole Mounted and also bracket mounted,

provided with high quality potted driver for protection against, high and low Voltage cut Off,

opertional for high amibient and high humid envirnoments, THD of driver should be less than

10% and P.F > 0.95. Also the Fixture should meet the following technical criterias. Operating

range Voltage 160 to 270 V, system efficiency > 110 lm/w, CCT > 5000K, CRI >65, beam angle

120 deg, 4kV integral & non integral surge immunity level at least 10 KV non integral... Flood

Light lumens shall be more than 9900. (Note:- The manufacturer / authorized Channel partner

of the manufacturer has to submit 5yrs free replcement Guarantee for complete Fixture)

ITEM NO DESCRIPTION QUANTITY UNIT RATE IN WORD AMOUNT

74 SITC of Outdoor aesthetically designed LED Street Light Luminaire with total consumption of 6.00 Each 6117.00 RS: Six Thousand

Max. 90W with single piece die cast aluminium housing, high power LED shall be mounted on One Hundred Seventeen

high quality metal core PCB with extremely precison designed heat sink complete with IP66 only

protection Class with polycarbonate / thoughened glass cover the fixture should be suitable for

pole/bracket mounting. The fixture to comply both LM79 and LM 80 guidelines with LED module

min. 130 lumen/watt with toughen Glass L70 at 50,000 hrs, provided with high quality

polycarbonate lenses for better light distribution. The watt capacity of Each LED must be >=4W

in street light fitting. The Fixture Should be able to be Pole Mounted and also bracket mounted,

provided with high quality driver for protection against high and low Voltage cut Off, opertional

for high amibient and high humid envirnoments, THD of driver should be less than 10% and P.F

> 0.95. Also the Fixture should meet the following technical criterias Oprating range Voltage

to 270 V, system efficiency >= 110 lm/w, and total lumens not less then 9900, CCT > 5000K,

CRI > 65, beam angle 120 deg, surge immunity level at least 4 KV integral and 10 KV non

integral (Note:- The manufacturer / authorized Channel partner of the manufacturer has to

submit 5yrs free replcement Guarantee for complete Fixture)

75 Supplying and erecting approved make Octagonal pole made from HR sheet steel. The pole 8.00 Each 6917.00 RS: Six Thousand

should be made as per IS. and shall be coated with hot dip galvanizing as per IS Nine Hundred Seventeen

2629/2633/4759, suitable suspend local wind speed with integral Junction box with Hot Deep only

Galvanised door having 2 nos. 180° operated hinges & 2 nos. Ln key locking with silicon rubber

gasket. Consist of terminal plate of min 6mm Hylam sheet, standard profile 35 mm X 7.5 mm Din-

Rail & MCB, Brass stud type terminal and arrangement for cable termination to be erected on

RCC foundation as per details given by manufacturer and EIC considering site requirement.

Foundation Details: (1) Grade of RCC 1:2:4, (2) Grade of steel rainforcement of RCC FE

(3) Clear cover to rainforcement 50mm, (4) Concrete vibrated, (5) use suttering / farma, (6) Hot

deep galvanized average 70 Micron, (7) Detail drawing will be given by corporation

(C) 5 Mtr. Long 70 mm Top X 130 mm bottom dia, 3 mm thickness with 200 mm X 200 mm X

12 mm base plate, 4-M16 Bolts and 600 mm long hot deep galvanized J-Bolt, nuts, washers with

800 mm under ground and 200 mm above ground level and Foundation in 1:2:4 proportion as

per details given by manufacturer and EIC considering site requirement. Approx Pole weight

kg.(Make:- Bajaj, Valmont, Transrail, Ambica Only) (Test certificate to be submitted)

76 Supplying and making Coil type earthing, coil made from 8 SWG galvanised iron wire with 50 mm OD 12.00 Each 369.00 RS: Three Hundred

and 50 turns (length of turns approx. 200 mm) and having additional continuous streight length of 3.00 Sixty Nine only

mtr at open end and should be connected to earthing bolt and burried in 1.5 mtr deep specially

prepared earth pit complete with salt and charcoal/coke as required for coil type earthing.(Approx

weight of coil 1.0 to 1.1 Kgs)

77 Providing & Erecting Universal Astro 5 KVA intelligent streetlight control system insu with 1.00 Each 12895.00 RS: Twelve Thousand

weather proof box for outdoor application. (As per specification attached separately) (Make and Eight Hundred Ninty Five

model approved by EIC) only

ITEM NO DESCRIPTION QUANTITY UNIT RATE IN WORD AMOUNT

78A Providing & erecting bracket consisting of ISI mark "B" class G.I. Pipe 4.2 cm outside diameter 11.00 Each 487.00 RS: Four Hundred

complete with suitable G.I. Sleeve tubing of 2 mm. thick and required size and length suitable for Eighty Seven only

76.5 / 80 mm. required size of pole top or pipe in pipe surface for terrace as per instruction of

EIC or wall bracket as per instruction of EIC having nuts and bolts for fixing the brackets and

having spread of Upto 0.50 mtr. length with suitable rise as per site condition and suitable

welded stiffner reducer and nipple with check nut complete painted with one coat of yellow zinc

and two coats of alluminium paint for Single arm bracket suitable for pole or terrace as per

design given by EIC (a) For single arm bracket. (Jindal / Asian / Tata / Surya Prakash make

Only) (Fabricators:- Bajaj, Valmont, Transrail, Ambica Only) (Test certificate to be submitted)

78B For Double arm bracket. (Jindal / Asian / Tata / Surya Prakash make Only) (Fabricators:- Bajaj, 1.00 Each 616.00 RS: Six Hundred

Valmont, Transrail, Ambica Only) (Test certificate to be submitted) Sixteen only

79 Providing & Erecting Flexible PVC insulated multistrand multicore 1.1 kv grade ISI marked 100.00 Mtr 46.00 RS: Forty Six

copper wires of following size to be erected as directed. 3 core 1.5 sq.mm. PVC insulated round only

copper wire ISI mark.

80 Providing & Erecting Flexible PVC insulated multistrand multicore 1.1 kv grade ISI marked 50.00 Mtr 77.00 RS: Seventy Seven

copper wires of following size to be erected as directed. 3 core 2.5 sq.mm. PVC insulated round only

copper wire ISI mark.

81 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand Copper 469.00 Mtr 361.00 RS: Three Hundred

conductor for 1.1 KV. to be laid on wall with necessary clamps 1.00 mm thick to be laid 90 cms Sixty One only

underground with 1.00 mm thick G.I heavy duty grade or in existing trench / pipe at road

crossing or floor of following size of cables.(A) 4 core 4 Sq. mm

82 Providing & erecting XLPE (IS : 7098) (I)-88 ISI marked armoured Aluminium conductor cable 20.00 mtr 152.00 RS: One Hundred

for 1100 volt to be laid 90 cms. Under ground or to be laid on wall with 1.00 m.m thick G.I. heavy Fifty Two only

guage cable clamp or in existing DWC pipe underground or road crossing or floor .For 4 core

83 Providing & laying HDPE Double walled corrugated pipes (DWC) (conforming to IS: 16205 (part 24) 450.00 Mtr 117.00 RS: One Hundred

2018)) with minimum load required of 450N capacity with anti rodent and ultra violet material Seventeen only

properties with necessary connecting accessories of same material at required depth to be laid

90 cms. under ground for laying of cable below ground / road surface for enclosing cable and

back filling the same to make ground as per original. (A) For Outer dia. 50 mm and Inner dia.

38 mm. ) (Test Certificate to be Submitted)

84 Supplying and erecting Fabricating terminal box for street light pole made from 16 SWG M.S. 2.00 Each 702.00 RS: Seven Hundred

sheet having following size complete with fixing arrangement for terminal board, with necessary Two only

hole for wire entry and exit from the box. The box shall be provided with cover and hinges on

one side and bolting at other end The box shall be fixed by clamps fabricated from 25mm x 6mm

flat.The box shall be painted with one coat of red oxide and two coats of paint having following

box size 330 mm x 260 mm x 140 mm (depth). Providing and fixing Terminal board of size 5.0 x

127 x 152.4 mm.bakelite sheet with 15 Amp. kitkat pattern porcelain fuse unit with suitable brass

studs with nuts, washers and clamps of size 25 mm x 3 mm suitable for pole painted with one

coat of red lead paint.

ITEM NO DESCRIPTION QUANTITY UNIT RATE IN WORD AMOUNT

85 Supplying & erecting approved make SMC press moulded composite FRP. loop-in, loop-out 4.00 Each 890.00 RS: Eight Hundred

approx. 2mm thick box complete with Bakelite connector strip 5way(3P+N+E), DIN rail for Ninty only

mounting mob & hinged doors as per requirement having locking arrangements with mounting

clamp with nuts, bolts & washers suitable for erection on pole with cable clamps& earth bolt of

following size of box. (A) 300mm x 200mm x 100mm

86 Providing & fixing Double compressed heavy duty flange type brass cable gland with rubber 10.00 Each 43.00 RS: Forty Three

ring for P V C insulated armoured cable complete with outgoing tails, insulating tape etc. For only

following size cables. For 2 to 4 core x 4.0 Sq. mm (Sigma, MCI, Comet, HMI Make Only)

87 Providing & fixing Double compressed heavy duty flange type brass cable gland with rubber ring 8.00 Each 57.00 RS: Fifty Seven

for P V C insulated armoured cable complete with outgoing tails, insulating tape etc. For only

following size cables. For 2 to 4 core x 16.0 Sq. mm

88 Providing & fixing Solderless crimping type Copper lugs conforming to IS suitable for cable of 180.00 Each 8.00 RS: Eight only

following size evenly crimped with high pressure tool & connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved manner. [a] 1.5/2.5 to 6 Sq.mm

89 Providing and erecting required size Copper strip for earthing of H.T. OCB / ACB/ Transformer, 2.00 KG 787.00 RS: Seven Hundred

LT panel board, Motors etc. using copper clamp. Eighty Seven only

90 Providing and erecting busbar chamber confirming to IS-375 fabricated from 16 G.M.S. sheet, 0.50 Rn Mtr 4378.00 RS: Four Thousand

dust & vermin proof having hinged door with rubber gasket and necessary busbar supports with Three Hundred Seventy

COPPER busbar having current density not more than 1.6 Amp. / sq.mm (Rated current / cross Eight only

section area) duly wrapped with colour insulation tape for phase sequence, three phase &

neutral each suitable for following current capacity with necessary painting mounted on wall or

pedestal frame of required size with necessary connections..(A) Suitable for 63/ 100 Amp. Capacity

91 Providing and erecting open well type horizontal submersible mono block pump set with cast 2.00 Each 15552.00 RS: Fifteen Thousand

iron body having following specification [E] For 3 phase open well horizontal mono block pump Five Hundred Fifty Two

set suitable for 270 LPM discharge at required head as per plumbing length and vertical & only

Horizontal head.Agency has to submit the details calculation of head to GSPHCL and get

approval of make and model of pump having tender specification with TDS & GA drawing.

Suitable for 50/65 mm dia delivery pipe with 10 mtr. necessary Size 3 Core Flat copper flexible

cable. (Body: Cast iron / Winding : Copper / stator : Copper / rotor : Copper / shaft : SS

material test certificate from manufacture shall be submitted).

The model of the pump with respect to head and discharge will be approved by EIC. Pump

should have following specifications:(1) Minimum 10 mtr. Cu. flat cable of suitable size must be

provided with pump.(2) Pump shall be installed as per manufacturer foundation/erection drawing

or as per IS specification (Body full C.I., stator winding- copper, rotor- copper, shaft- SS

motor-Energy efficiency)

92 Lowering of submersible motor pump set at the depth of following ,complete with required. 2.00 Each 848.00 RS: Eight Hundred

Nos. and size of casing pipes erected by means of proper chain pulley block & pipe wrenches Forty Eight only

after checking of threads of each pipe with coupling to take the load of the pump set and pipe

assembly filled up with water (D)For Open well Horizontal submersible pump set for sump

well (i) 1 HP to 5 HP

ITEM NO DESCRIPTION QUANTITY UNIT RATE IN WORD AMOUNT

93 Supplying and erecting approved make 3 HP DOL type motor control cubical panel made from 16 G. CRCA 1.00 Each 47062.00 RS: Forty Seven

sheet duly epoxy powder painted inside and outside with hinged doors and locking arrangement Floor Mounting Thousand Sixty Two

On 300 mm Height with MS Stand Angle & CC Foundation. Size 35 mm (H) x 35 mm (W) x 05 mm (D). The

detail specification & quantity of material used are as under.

Panel must be with minilec relay for auotmatic change over for pump 1 & 2 logically without using manually

change over switch (Minimum Panel Size: 1.10 meter (H) x 1.10 meter (W) x 0.25 meter (D).

INCOMMER SECTION: (1) MCCB-30 KA-FP (Ics = 100% Icu), Rating: 63 Amp., Make: L&T, Qty: 01 No. (2)

Digital Ammeter (SR-65), Rating: 0-60 Amp., Make: Meco, Qty: 01 No. (3) Ammeter Selector Switch, Rating:

Amp., Rotary, Make: Salzer, Qty: 01 No. (4) Digital Voltmeter (SR-65), Rating: 0-500 V, Make: Meco, Qty:

No. (5) Volt Selector Switch, Rating: 6 Amp., Rotary, Make: Salzer, Qty: 01 No. (6) C.T.- Current Transformer,

Rating: 60/5 Amp., Make: Virat, Qty: 03 Nos. (7) Indicating Lamps (R,Y,B), Rating: 22.5 mm LED, Make: Airon,

Qty:03 Nos. (8) SP MCB , Rating: 20 Amp., Make: L&T , Qty: 03 Nos. (9) Control Wiring, Rating: 1.0 Sq.mm,

Make: Any ISI, Qty: Lot (10) Copper Busbar, Rating: 63A/100 Amp., Qty: Lot (11) Numeric logical relay, Qty:

Outgoing Feeder (5 HP DOL Feeder): Qty: 02 Nos. (1) MCB-FP-10 KA, Rating: 20 Amp., Make:

L&T, Qty: 02 Nos. (2) Power Contactor (415 V) Main, Rating: 12 Amp., Make: L&T, Qty: 02 Nos.

(3) Over Load Relay, Rating: 9-15 Amp., Make: L&T, Qty: 02 Nos. (4) Digital Ameter (SR-65),

Rating: 0-20 Amp., Make: Meco, Qty: 02 Nos., (5) Digital Voltmeter (SR-65), Rating: 0-500 V,

Make: Meco, Qty: 02 Nos. (6) Indicating Lamps (Start,Run,Trip), Rating: 22.5 mm LED, Make:

Airon, Qty: 04 Nos. (7) Push Button (Start,Stop), Rating: 22.5 mm, Make: Airon, Qty: 02 Nos. (8)

SPP, Rating: 415 V, Make: Space, Qty: 02 Nos. (9) Terminal, Rating: As per Amp., Make: Airon,

Qty: 04 Nos. (10) Control Wiring, Rating: 1.0 Sq.mm., Make: Any ISI, Qty: Lot (11) Power Wiring,

Rating: As Per Amp., Make: Any ISI, Qty: Lot

Outgoing Feeder (6 Amp. - 01 No.) For Capacitor (1) MCB-FP-10 KA, Rating: 6 Amp., Make:

L&T, Qty: 01 No. (2) Capacitor- MPP Type, Rating: 2 KVAr, Make: Concap, Qty: 01 No., (3)

Power wiring, Rating: As Per Amp., Make: Any ISI, Qty:Lot

Outgoing Feeder (32 Amp. - 01 No.) For Lighting (1) MCB-FP-10 KA, Rating: 32 Amp., Make:

L&T, Qty: 01 No. (2) Power wiring, Rating: As Per Amp. (3) Earthing Strip: 25 x 3; G.I. Strip, Qty:

01 No. (4) MCB-DP-10KA , Rating: 20A, Make: L&T, Qty.:01 Nos.

94 Providing & erecting ISI make medium duty (B class) galvanized MS pipe with coupling, bend, 12.00 Mtr. 260.00 RS: Two Hundred

union, reducer, tee, MS flange etc. with plumbing charges. [d] 50 mm dia( If required) Sixty only

95 Supplying and erecting C.I. Swing check type non-return (reflux) valve ISI marked with packing, 3.00 Each 1010.00 RS: One Thousand

flange, nuts and bolts etc.suitable for following pipe size. [B] For 50 mm dia. Ten Hundred Ten

(SANT,KIRLOSKAR,LEADER,ZOLOTO) ( If Required) only

96 Supplying Water tight M.S.Box of size 20 x 15 x 15 cms. to erect suitable kitkat fuse / MCB to 1.00 Each 232.00 RS: Two Hundred

be . erected on polished wooden board inside the box with hinged/sliding door with rubber rings Thirty Two only

and erected on pole with suitable pole clamp, all duly painted with one coat of red oxide and two

coats of paints. (Cost of Fuse / MCB shall be taken extra) [Provision for motors cable joints near

97 Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible Submersible 10.00 Mtr. 103.00 RS: One Hundred

copper cable approved make of following Size. (A) For 3 Core x 2.5 Sq. mm. Three only

ITEM NO DESCRIPTION QUANTITY UNIT RATE IN WORD AMOUNT

98 Dismantling the existing light, fan, bell, clock, independent plug point, wiring with mains of all 100.00 Each 1.00 RS: One only

types along with accessories etc. complete.

99 Dismantling the existing switchgears, DB and Busbar of any size complete with / without board or 72.00 Each 7.00 RS: Seven only

angle iron frame.

100 Dismantling the existing ceiling fan / exhaust fan / cabin fan / bracket fan complete with 72.00 Each 9.00 RS: Nine only

accessories, G.I. down rod, frame etc. and making the site clear.

101 Dismantling the existing any type of indoor light fittings. 150.00 Each 5.00 RS: Five only

102 Providing and fixing of ABC Type Store Pressure Fire Extinguisher Having capacity 6 kg Filled with 2.00 Each 1991.00 RS: One Thousand

Mono Ammonium Phosphate Powder 50% confirms to IS 4308, Stored Pressure Type, UGTS Nine Hundred Ninty One

Pressure Gauge, Can Height 530 mm, Diameter 150 ± 10mm, Discharge Time 24 Sec, Controllable only

discharge mechanism, Jet Range 5 Meters, Average Discharge is 92%, applicable on Class A,B & C

and electrically started Fire, Fire Rating 4A:144B, Can Construction : Deep drawn & CO2 Mig welded,

EPDM(Ethylene Propylene Diene Monomer) Rubber Hose with both end Aluminum clamped,

Internal Coating - Epoxy Powder coating, External Coating - Pure Polyester Powder coating (UV

Resistant),Brass forged CE Marked valves with NRV & Auto Safety Release with safety Pin is of

SS material, Made up from 1.6mm thick sheet, Extinguishers confirmed to IS 15683:2018 and ISI

marked. Referance Weight:-Gross Weight 8.9 Kg, Empty Weight 2.9 Kg, 1. Necessary certificate &

and guarantee must be attached, 2. OEM has to provide wall mounting heavy duty bracket/clamp,

screw, hardware for installation. 3.Following printed marking Manufacturing Date and Expiry Date must

be mention on Extinguisher 4. Refilling period must be of 3 Years. Following Printed marking on

equipment must be required:- Model No, Capacity, Gross Weight, Content, Fire Rating, Batch No,

Serial no, Mfg Month, Refilling Due. [with necessary numbering / marking with oil paint by painter as

instructions given by G.S.P.H.C.L engineer] (Make: KANEX, MINIMAX, CEASEFIRE)

ITEM NO DESCRIPTION QUANTITY UNIT RATE IN WORD AMOUNT

103 Providing and fixing of CO2 type High Pressure Portable 4.5 kg Fire Extinguisher, filled with 2.00 Each 6526.00 RS: Six Thousand

Co2 Gas as per IS 15222, Control discharge mechanism fitted with 1 Meter Wire Braided Five Hundred Twenty Six

Hose & Electrical non-conductor Polyethylene Flat Horn with Diffuser Nozzle for dispersed only

discharge of CO2, Discharge Time 12 Sec, Average Discharge is 95%, Applicable on Class B, C

and electrically started Fire, Fire Rating 55B, Internal coating is not applicable & External

coating is of enamel spray painting, Powder Coated Handle, Valve Confirm to IS 3224 ISI

Marked, CO2 Cylinder construction: hot spinning by seamless pipes & bearing ISI mark, Body

confirms to IS 7285 and PESO ( Petroleum and Explosives Safety Organization)

APPROVED, Minimum Wall Thickness 4 to 4.2 mm, Extinguishers confirmed to IS

15683:2018 and ISI marked. Referance Weight:-Gross Weight 16.4, empty weight 11.9 Kg,

Necessary certificate & and guarantee must be attached, 2. OEM has to provide wall mounting

heavy duty bracket/clamp, screw, hardware for installation. 3.Following printed marking

Manufacturing Date and Expiry Date must be mention on Extinguisher 4. Refilling period must

be of 5 Years. Following Printed marking on equipment must be required:- Model No, Capacity,

Gross Weight, Content, Fire Rating, Batch No, Serial no, Mfg Month, Refilling Due. [with

necessary numbering / marking with oil paint by painter as instructions given by G.S.P.H.C.L

engineer] (Make: KANEX, MINIMAX,CEASEFIRE)

TOTAL ELECTRIFICATION WORK

TOTAL CIVIL & ELECTRIFICATION AMOUNT OF RS.

Signature of Contractor DY.Executive Engineer Executive Engineer

Ahmedabad. Ahmedabad.