JJM -CWSS to Elavanchery Pallassana

Amount

Cost of Pipes

OD206046/2022-2023:Supplying ERW pipe - In situ fabrication of MS pipes of size 530mm (I.D) 10mm thick MS plate including cost and Conveyance charges of MS plate, all fabrication charges, charges of painting the steel work with two or more coat outer side coal tar epoxy paint to give an even shade over an under-coat of primer and Cement mortar lining with CM 1:2 , 15mm thick at 80% sand and 20% jelly of size less than 80mm for internal lining inner & paint etc complete Details of cost for 1m pipe . Length of pipe 100cm Internal Diameter of pipe 530mm Thickness of plate 10mm outer diameter of pipe 550mm average diameter of pipe 540mm weight of MS plate 78.50Kg/m2 Perimeter of pipe 1727mm Area of MS sheet 1.695m2 weight of sheet 133.10kg add 5% wastage 6.66Kg Total weight of MS plate 139.76Kg

OD206047/2022-2023:Supplying ERW pipe - In situ fabrication of MS pipes of size 330mm (I.D) 10mm thick MS plate including cost and Conveyance charges of MS plate, all fabrication charges, charges of painting the steel work with two or more coat out side coal tar epoxy surface paint to give an even shade over an under-coat of primer and Cement mortar lining with CM 1:2 , 15mm thick at 80% sand and 20% jelly of size less than 80mm for internal lining inner etc complete Details of cost for 1m pipe . Length of pipe 100cm Internal Diameter of pipe 330mm Thickness of plate 10mm outer diameter of pipe 350mm average diameter of pipe 340mm weight of MS plate 78.50Kg/m2 Perimeter of pipe 1099mm Area of MS sheet 1.067m2 weight of sheet 83.806kg add 5% wastage 4.19Kg Total weight of MS plate 87.996Kg

OD205817/2022-2023:In situ fabrication of MS pipes of size 1400mm (I.D) using 20mm thick MS plate including cost and conveyance charges of MS plate , all fabrication charges , charges of painting the steel work with two or more coat inner & outer coal tar epoxy paint to give an even shade over an under-coat of primer etc, complete. Details of cost for 1m pipe . Length of pipe 100cm Internal Diameter of pipe 1400mm Thickness of plate 20mm outer diameter of pipe 1440mm average diameter of pipe 1420mm weight of MS plate 157Kg/m2 Perimeter of pipe 4521.6mm Area of MS sheet 4.4588m2 weight of sheet 700.0316kg add 5% wastage 35.0015Kg Total weight of MS plate 735.03318Kg

OD281783/2022-2023:Supplying ERW pipe - In situ fabrication of MS pipes of size 200mm (I.D) 10mm thick MS plate including cost and Conveyance charges of MS plate, all fabrication charges, charges of painting the steel work with two or more coat out side coal tar epoxy surface paint to give an even shade over an under-coat of primer etc complete Details of cost for 1m pipe . Length of pipe 100cm Internal Diameter of pipe 200mm Thickness of plate 10mm outer diameter of pipe 220mm average diameter of pipe 210mm weight of MS plate 78.50Kg/m2 Perimeter of pipe 690.8mm Area of MS sheet 0.659m2 weight of sheet 51.73kg add 5% wastage 2.58Kg Total weight of MS plate 54.31Kg

100.98.123:Supply of DI K9 Pipe Conforming to IS 8329/2000, 500mm Dia.

100.98.119:Supply of DI K9 Pipe Conforming to IS 8329/2000, 300mm Dia.

100.98.118:Supply of DI K9 Pipe Conforming to IS 8329/2000, 250mm Dia.

100.98.174:Supply of HDPE Pipe PE 100 (IS 4984/1995), 12.5kg, 90mm Outer Dia.

18.12.8:Providing and fixing G.I. pipes complete with G.I fittings including trenching and refilling etc. External work80 mm dia nominal bore

100.98.451:Supply of CI Air Valve with Flanges, Conforming to IS 14845 - 2000, Kinetic Air Valve Type DS1, Size 100mm.

18.68.1:Providing and laying D.I specials of class K - 12 suitable for push - on jointing as per IS : 9523 :Upt 600 mm dia

OD206520/2022-2023:Supply of PE specials 3% cost of pipe

OD274600/2022-2023:Supply of PVC specials 3% cost of PVC pipe

OD207431/2022-2023:Supplying and fabricating MS Reducer 10mm thick size 550mmX500mm including cutting, Grinding, Welding charges

OD207474/2022-2023:Supplying fabricated MS Reducer 10mm thick size 350X300mm including cutting, grinding, welding charges

Working charges

100.1.1:Excavating trenches of required width for pipes, cables, etc., including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering, etc., and disposing of surplus excavated soil as directed, within a lead of 50m, in all kinds of soil.

100.1.6:Excavating trenches of required width for pipes, cables, etc., including excavation for sockets, and dressing of sides, ramming of bottoms, depth exceeding 1.5m but not exceeding 3m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering, etc., and disposing of surplus excavated soil as directed, within a lead of 50m, in Ordinary Rock.

100.8.1:Fencing one side of trenches, 1.50m height with two rows of 10cm plastic caution tape in vertical casuarina pole (girth 15cm to 24cm) fixed at 2m intervals.

100.9.8:Laying uPVC pipes of class 2 to class 6 and specials, lowering to the trenches already made, placing in position aligning the pipeline to the lines and levels and jointing the pipes and specials with solvent cement and testing the pipeline with water to the required test pressure (excluding cost of pipes and specials): 90 mm nominal outside diameter pipes.

100.10.1:Laying HDPE pipes (IS : 4984) on land portion including conveying within initial lead and aligning the pipes, electro-fusion welding using automatic or semi-automatic electrofusion machines, testing the pipeline thus fabricated to suit the hydraulic working pressure and after testing, aligning the pipeline, lowering the pipe in position into the trenches already made, testing the line to suitable pressure with potable water before back filling and levelling the trenches including all labour charge, hire for appliances etc., complete but excluding cost of pipe and fittings: 90mm Nominal Outer Diameter pipes.

100.14.4:Conveying and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS: 8329 excluding cost of pipes and specials: 250mm diameter Ductile Iron Class K-9 Pipes.

OD206194/2022-2023:Labour for cutting DI pipe with steel saw. - 250 diameter DI pipe

18.70.4:Providing push - on-joints to Centrifugally (Spun) Cast Iron Pipes or Ductile Iron Pipes including testing of joints and including the cost of rubber gasket:250 mm dia pipes

100.14.5:Conveying and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS: 8329 excluding cost of pipes and specials: 300mm diameter Ductile Iron Class K-9 Pipes.

18.70.5:Providing push - on-joints to Centrifugally (Spun) Cast Iron Pipes or Ductile Iron Pipes including testing of joints and including the cost of rubber gasket:300 mm dia pipe

OD206195/2022-2023:Labour for cutting DI pipe with steel saw - 300 mm Dia DI pipe

100.14.9:Conveying and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS: 8329 excluding cost of pipes and specials: 500mm diameter Ductile Iron Class K-9 Pipes.

OD206196/2022-2023:Labour for cutting DI pipe with steel saw 500mm dia DI pipe

18.70.9:Providing push - on-joints to Centrifugally (Spun) Cast Iron Pipes or Ductile Iron Pipes including testing of joints and including the cost of rubber gasket:500 mm dia pipes

100.32.5:Conveying and fixing C. I. Double Acting Air Valve of approved quality with bolts, nuts, rubber insertions etc., complete, but excluding the cost of air valve (tail pieces, if required, will be paid separately): 100mm Double Acting Air Valve.

100.35.4:Testing 250mm DI/CI pipeline with potable water to the required test pressure . 250 mm dia Observed Data derived from item no.1022 of PHED DATA

100.35.5:Testing 300mm DI/CI pipeline with potable water to the required test pressure. 300 mm dia Observed Data derived from item no.1023 of PHED DATA

100.35.9:Testing 500mm DI/CI pipeline with potable water to the required test pressure. 500 mm dia Observed Data derived from item no.1028 of PHED DATA

100.59.1:Cutting the bituminous / concrete roads with cutting machine for a minimum depth of 200mm along the sides of proposed alignment of the pipe to be laid without causing any damage to other utilities, including the charges for hire and conveyance of tools and plant, cost of consumables and charges for lighting, watching, ribbon fencing, caution boards, traffic diversion, and as per the direction of departmental officers etc. complete, before carrying out the demolition of bituminous / concrete road by mechanical means and carrying out the excavation.

5.1.2:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size

4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

16.78.3:Construction of granular sub- base by Providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, Carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in- Charge.With material conforming to Grade - III ( size range 26.5 mm to 0.075 mm) having CBR Value - 20

OD206201/2022-2023:Towards the charges for conveying Horizontal Drilling Devices after loading in to container truck from Kozhikkode/Ernakulam (the nearest place where the devices are available at presnt) to work site at Erimayur, unloading the device using moving crane with out making any damage to the machine as well as to any structures or establishment belonging to NH, making necessary temporary road at site for conveying and placing the device at exact location for drilling as directed by NH authorities, levelling site properly for setting the machine, conveying the pushing pulling device to the other side of road setting the pushing pulling device at the other end of the road up to which the casing pipe of MS 1400mm diameter pipe is to be pulled, starting the horizontal drilling work across the Erimayur-Kavassery Road after informing the NH authorities and doing the work in their presence so that no interruption in road traffic will occur during the course of work , Pulling the 1400mm diameter MS casing pipe (already welded joint and connected each other using bus hand conveyed to site ready for laying) carefully through the drilled hole in line and levels without causing any damage , cleaning the inside of the pipe for laying the 500,300mm ERW pipe through it easily, removing the machines after completing the work carefully restoring the site to original position, including the conveyance charges, loading and unloading charges, Labour engaged for clearing the site, earthwork excavation in hard soil, drilling charges, pushing and pulling charges , Cost of fuel and sundries required for the operation including cost of casing pipe etc. complete. - Maximum out turn of the work for 1400mm diameter pipe is 3m in a day

OD281815/2022-2023:Towards the charges for conveying Horizontal Drilling Devices after loading in to container truck from Kozhikkode/Ernakulam (the nearest place where the devices are available at presnt) to work site at Erimayur, unloading the device using moving crane with out making any damage to the machine as well as to any structures or establishment belonging to NH, making necessary temporary road at site for conveying and placing the device at exact location for drilling as directed by NH authorities, levelling site properly for setting the machine, conveying the pushing pulling device to the other side of road setting the pushing pulling device at the other end of the road up to which the casing pipe of MS 200mm diameter pipe is to be pulled, starting the horizontal drilling work in between Erattakkulam to Cheekkode Road (left side)after informing the NH authorities and doing the work in their presence so that no interruption in road traffic will occur during the course of work , Pulling the 200mm diameter MS casing pipe (already welded joint and connected each other using bus hand conveyed to site ready for laying) carefully through the drilled hole in line and levels without causing any damage , cleaning the inside of the pipe for laying the 90mm HDPE pipe through it easily, removing the machines after completing the work carefully restoring the site to original position, including the conveyance charges, loading and unloading charges, Labour engaged for clearing the site, earthwork excavation in hard soil, drilling charges, pushing and pulling charges , Cost of fuel and sundries required for the operation including cost of casing pipe etc. complete. - Maximum out turn of the work for 200mm diameter pipe is 10m in a day (Left side Ch. 230.000 to 230.420 and Right side ch. 229.450 to 229.500)

OD206202/2022-2023:Cutting 530mm MS pipe for making bends and other specials by gas cutting including cost of gas, all labour and hire charges of tools etc, complete for pipes fabricated with 10mm thick MS plates. Details of Cost For each Internal Diameter of Pipe 500.00 mm Thickness of Plate 10.00 mm Outer diameter of Pipe 520.00 mm Length of cutting 1633.63 mm

OD206203/2022-2023:Grinding cut and weld edges of 530mm (I.D.) M.S. pipes during fabrication work including all labour and hire charges of tools etc., complete: For pipes fabricated with 10mm thick M.S. plates. Details of Cost For each Internal Diameter of Pipe 530.00 mm Thickness of Plate 10.00 mm Outer diameter of Pipe 550.00 mm Length of grinding 1727 mm

OD206204/2022-2023:Welding 530mm (I.D.) M.S. pipes for making bends and other specials by gas/electric welding machine including cost of gas and welding rods, all labour and hire charges of tools etc., complete: For pipes fabricated with 10mm thick M.S. plates. Details of Cost For each Internal Diameter of Pipe 530.00 mm Thickness of Plate 10.00 mm Outer diameter of Pipe 550.00 mm Length of welding 1727 mm

OD206205/2022-2023:Cutting 330mm MS pipe for making bends and other specials by gas cutting including cost of gas, all labour and hire charges of tools etc, complete for pipes fabricated with 10mm thick MS plates. Details of Cost For each Internal Diameter of Pipe 330.00 mm Thickness of Plate 10.00 mm Outer diameter of Pipe 350.00 mm Length of cutting 1099 mm

OD206206/2022-2023:Grinding cut and weld edges of 330mm (I.D.) M.S. pipes during fabrication work including all labour and hire charges of tools etc., complete: For pipes fabricated with 10mm thick M.S. plates. Details of Cost For each Internal Diameter of Pipe 330.00 mm Thickness of Plate 10.00 mm Outer diameter of Pipe 350.00 mm Length of grinding 1099 mm

OD206207/2022-2023:Welding 330mm (I.D.) M.S. pipes for making bends and other specials by gas/electric welding machine including cost of gas and welding rods, all labour and hire charges of tools etc., complete: For pipes fabricated with 10mm thick M.S. plates. Details of Cost For each Internal Diameter of Pipe 330.00 mm Thickness of Plate 10.00 mm Outer diameter of Pipe 350.00 mm Length of welding 1099 mm

OD206912/2022-2023:Grinding cut and weld edges of 1400mm (I.D) MS pipes during fabrication work including all labour and hire charges of tools etc complete. For pipes fabricated with 20mm thick MS plates . Details of cost for each internal diameter of pipe 1400mm thickness of plate 20mm outer dia of pipe 1440mm length of grinding 4521.60mm

OD206913/2022-2023:Welding 1400mm (I.D) MS pipes for making bends and other specials by Gas /Electric welding machine including cost of gas, all labour and hire charges of tools etc complete for pipes fabricated with 20mm thick MS plates. Details of cost for each internal diameter of pipe 1400mm thickness of plates 20mm outer diameter of pipe 1440mm length of welding 4521.60mm

OD206914/2022-2023:Cutting 1400mm (I.D) MS pipes for making bends, and other specials by gas cutting including cost of gas , all labour and hire charges of tools etc,. complete for pipes fabricated with 20mm thick MS plates

OD282022/2022-2023:Welding 200mm (I.D) MS pipes for making bends and other specials by Gas /Electric welding machine including cost of gas, all labour and hire charges of tools etc complete for pipes fabricated with 10mm thick MS plates. Details of cost for each internal diameter of pipe 200mm thickness of plates 10mm outer diameter of pipe 220mm length of welding 690.8 mm

OD282023/2022-2023:Grinding cut and weld edges of 200mm (I.D) MS pipes during fabrication work including all labour and hire charges of tools etc complete. For pipes fabricated with 10mm thick MS plates . Details of cost for each internal diameter of pipe 200mm thickness of plate 10mm outer dia of pipe 220mm length of grinding 690.80mm

OD282025/2022-2023:Cutting 200mm (I.D) MS pipes for making bends, and other specials by gas cutting including cost of gas , all labour and hire charges of tools etc,. complete for pipes fabricated with 10mm thick MS plates

KEYEM INFRA PROJECT PRIVATE LIMITED

Bidder Name

Koya and Company Construction Limited

KEYEM INFRA PROJECT PRIVATE LIMITED