GE AF/AMB-18/2020-21 REPAIRS TO PATHS, HARD STANDING, DRAINS, BOUNDARY WALLS, FENCING, SEWAGE LINES AND CAMOUFLAGE PAINTING AT SITE-III (BAKNAUR) UNDER GE (AF) AMBALA

Amount

Excavating in post holes (or similar holes) each not exceeding 0.5cum, returning, filling in, getting out in soft / loose soil and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm and removing surplus soil to a distance not exceeding 50m complete all as specified and as directed

Dismantling posts or struts (wood, steel or RCC) any section, including taking out embedded portion and making good disturbed ground complete all as specified and as directed

M&L for dismantling rusted / damaged fencing of any size / type and disposing off complete all as specified and as directed

Demolition of cement concrete of any description and in any position not otherwise specifically provided for and removal of debris and depositing where directed at a level not exceeding 1.5m above the starting point to low lying areas, including all cartage, etc. complete all as specified and as directed

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) as in cover slabs, removing debris from site and making good the disturbed surfaces / portions in existing specifications complete all as specified and as directed

Demolition of brickwork or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc but excluding ashlar facings, dressed stonework and precast concrete articles and disposing off complete all as specified and as directed

Demolition and breaking up 150mm bore drain pipes (salt glazed stoneware, AC or reinforced concrete) set in cement mortar and disposing off outside MD land including all cartage, etc. complete all as specified and as directed

Dismantling structural steel work including doors, gates but excluding framed trusses, etc. and disposing off complete all as specified and as directed

Taking down cement or cement lime plaster, any description on brick or stone walls, etc. including raking out joints, hacking for keys, scubbing down with water, etc. including all necessary scaffolding as required and rubbishing off the premises, etc. complete all as specified and as directed

M&L for cutting into existing manholes for connecting new drain pipes, 150mm bore, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and as directed

M&L for precast reinforced cement concrete 1:2:4 (type B-1) using 20mm graded stone aggregates as in fencing posts, straining or terminal posts, struts, etc. cross-sectional area not exceeding 100sqcm complete all as specified and as directed

M&L for plain cement concrete 1:4:8 (type D-2) using 40mm graded stone aggregate as in foundation filling, mass concrete, etc. complete all as specified and as directed

M&L for 75mm thick plain cement concrete 1:4:8 (type D-2) using 40mm graded stone aggregate as in sub-bases, pavings, etc. complete all as specified and as directed

M&L for plain cement concrete type B-1,1:2:4 (using 20mm graded stone aggregates) in locking of edges of inter-locking tiles, padding, PCC bed blocks and the like including weathering, slightly rounded or chamfered angles and throating, etc. complete all as specified and as directed

M&L for 100mm thick plain cement concrete type B-1,1:2:4 (using 20mm graded stone aggregates) as in floors, etc. finished to receive floor finishes, etc. complete all as specified and as directed

M&L for plain cement concrete type B-1,1:2:4 (using 20mm graded stone aggregates) as in coping, kerbs, throating, etc. including all necessary formwork, etc. complete all as specified and as directed

M&L for plain cement concrete type C-2,1:3:6 (using 40mm graded stone aggregates) as in foundations, bedding of manholes, surface channels, etc. complete all as specified and as directed

M&L for plain cement concrete 1:4:8 (type D-2) using 40mm graded stone aggregate for bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 150mm dia drain pipes complete all as specified and as directed

M&L for precast RCC 1:2:4 type B-1 using 20mm graded mechanically crushed stone aggregates as in cover slab for man holes, drains, soak wells, and similar articles, set in CM 1:4 with plain faces including necessary formwork and chamfering, weathering, throating, etc. complete all as specified and as directed

M&L for mild steel TMT bars grade Fe-500D, 10mm dia, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed

M&L for mild steel TMT bars grade Fe-500D, 5mm dia and over, upto and including 10mm dia, as in stirrups, spacers, etc. cut to length, bent to shape required including cranking, bending and binding with and including MS wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed

M&L for mild steel round bars 8 to 10mm dia and over, cut to length, bent to shape required and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as in supports to chain link fencing complete all as specified and as directed

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other or screwed at both ends, each screwed end to be fitted with washers and one hexagonal or square nut, not exceeding 5cm in length, dia of neck & shank 10mm complete all as specified and as directed

S&F angle iron posts & struts in fencing including cutting top to shape, drilling holes, notching for wire including all necessary drilling bolts or rivetting & similar works conforming to Fe-290 grade E-165 (for securing chain link fencing, etc.) complete all as specified and as directed

S&F MS flat iron fillets (for securing wire mesh, fencing, etc.) including all necessary drilling bolts or rivetting and similar works conforming to Fe-290 grade E-165 complete all as specified and as directed

M&L for framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc. drilled for fixing of steel sheeting or other covering, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging, also fastening and fixing conforming to Fe-410W grade E-250 quality -'B' complete all as specified and as directed

Supply only chain link MS galvanised fencing, any size or type complete all as specified and as directed

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provisioning of binding wire complete all as specified and as directed

M&L for brickwork with sub-class 'B' bricks, straight or curved on plan exceeding 6m mean radius built in CM (1:6) complete all as specified and as directed

--ditto-- all as per serial item No. 29 hereinabove but except bricks

M&L for brickwork with sub-class 'B' bricks, straight or curved on plan as in half brick thick walls built in CM (1:4) complete all as specified and as directed

M&L for continuous brick edging with burnt clay bricks, sub-class-B, with width equal to the length of the brick, laid dry on edge vertically complete all as specified and as directed

M&L rendering 15mm thick in cement mortar (1:4) on fair surfaces of PCC block / brick masonry wall / concrete surfaces, inner sides of drains, etc. finished even and smooth without using extra cement complete all as specified and as directed

M&L for rough cast plaster including 15mm thick rendering in CM 1:3 on brickwall or concrete surfaces complete all as specified in SSR Part-I clause 14.22 complete all as specified and as directed Note: Rough cast finish shall be made as under: (i) After applying the under coat of cement mortar 1:3 and while it is still in plasic state the rough cast mixture consisting of crushed stone or fine gravel / aggegates (of size between 6 to 12mm depending on the texture required) mixed with course sand and cement in the ratio of 1:1:1 shall be applied and finished even (ii) The mix of cement and sand shall be made slightly wetter than normal for rendering to ensure that larger aggregates are thoroughly covered

M&L for forming 12mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound grade ‘B’ for 100mm thick concrete slabs complete all as specified and as directed

M&L for preparing of new steel surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint (tint as approved) over a coat of red oxide zinc chrome primer complete all as specified and as directed

M&L preparation of new/old treated plastered / unplastered masonry / concrete wall surfaces, etc. and applying two coats of exterior acrylic anti-fungal paint (tint as approved by the GE) as per manufacturer's instructions with all staging as required complete all as specified and as directed

M&L preparation of old treated plastered / unplastered masonry / concrete wall surfaces, etc. and applying two coats of exterior acrylic anti-fungal paint (tint as approved by the GE) in camouflage pattern as per manufacturer's instructions with all staging, safety measures, etc. as required to work at heights complete all as specified and as directed

M&L preparation of old treated plastered / unplastered masonry / concrete wall surfaces, etc. and applying one coat of exterior acrylic anti-fungal paint (tint as approved by the GE) in camouflage pattern as per manufacturer's instructions with all staging, safety measures, etc. as required to work at heights complete all as specified and as directed

M&L preparation of new plastered / unplastered wall surfaces of any description and applying two coats of cement based paints (tint as approved by the GE) in camouflage pattern as per manufacturer's instructions with all staging as required complete all as specified and as directed

M&F for painting with spray gun to galvalume sheet roofs, etc. surfaces of any description over 10cm in width or girth not otherwise described with two coats of synthetic paint over a coat of primer in camouflage pattern including preparation of surfaces complete all as specified and as directed

M&F for painting with spray gun to asbestos cement sheet roofs, etc. surfaces of any description over 10cm in width or girth not otherwise described with two coats of acrylic emulsion anti-fungal paint over a coat of primer in camouflage pattern including preparation of surfaces complete all as specified and as directed

M&L for removing all loose / spalling out concrete from old surfaces of static water tanks, etc cleaning the exposed steel by sand blasting and providing and welding new reinforcement (if required and directed) to old steel and applying two coats of anti-corrosive zinc chromate paint (both on old and new steel), applying one coat of epoxy based adhesive over exposed surfaces to receive guniting, supplying and fixing MS welded wire mesh of size 100x100x3mm dia and binding with 22gauge binding wire with reinforcements and pressure guniting the surface with CM 1:3.5 with average thickness 30 to 50mm and then rendering the surface in 10mm thick CM 1:4, finishing the surface even and smooth without using extra cement, including all necessary scaffolding and staging and rubbishing off the premises complete all as specified and as directed

M&L for chequered cement concrete tiles 200x200x25mm thick, set, jointed and pointed in neat cement slurry in floors laid 20mm over bedding layer in CM 1:6 (cost shall be including) complete all as specified and as directed

M&L for laying pre-polished 80mm thick rubber moulded, double glossy, coloured, designer, interlocking tiles made of M-40 design mix concrete of approved design and shape with the crushing strength not less than 250kg/sqcm laid over and including 25mm thick (compacted thickness) sand bed (rate shall be inlcuded) complete all as specified and as directed

--ditto-- as per serial item No. 45 hereinabove but except inter-locking tiles

M&L for laying pre-polished 60mm thick rubber moulded, double glossy, coloured, designer, interlocking tiles made of M-40 design mix concrete of approved design and shape with the crushing strength not less than 250kg/sqcm laid over and including 25mm thick (compacted thickness) sand bed (rate shall be inlcuded) complete all as specified and as directed

S&F in repairs galvanised 2 strand, steel barbed wire 2.24mm dia, barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossings with and including provision of galvanised mild steel wire, staples or steel pins, etc. complete all as specified and as directed

Supply and laying slat glazed stone ware pipe, 150mm bore (internal dia), laid in trenches, jointed in cement mortar 1:2 including testing on laying / fixing complete all as specified and and directed

M&L for cleaning / de-sludging of sewer lines, upto 150mm bore, using mechanical pumps, diesel driven, with fuel, operator, etc. and all necessary tools / plants including loading and carting off the drawn sludge, waste material, scum, spoil water, etc. outside MD land through designated sludge carriers / bio tanks and flushing entire stretch with water to check functionality complete all as specified and as directed

M&L for cleaning / de-sludging of septic tanks / sewage sump wells of capacity 50 to 100 users, using mechanical pumps, diesel driven, with fuel, operator, etc. and all necessary tools / plants including loading and carting off the drawn sludge, waste material, scum, spoil water, etc. outside MD land through designated sludge carriers / bio tanks complete all as specified and as directed

Notes for serial item Nos. 50 & 51: (i) All necessary precautions and all safety measures as per Municipality rules / relevant regulatory guidelines shall be taken by the Contractor in employing his workmen in foul conditions to prevent any health hazards, etc. (ii) The Contractor shall be solely responsible for any mishap to any of labourer deployed and to equipment/machinery/plants/material, etc. brought at site for work and any lapses whatsoever during the execution, (iii) The work shall be executed under the supervision of highly skilled tradesman / supervisor, (iv) The rates quoted shall be deemed to be inclusive of the above aspects, and no claims whatsover shall be entertainable at later stages and or during execution

Swami Enterprises

s.v.builders

Bairagi Builders