BID DOCUMENTS FOR PROVIDING, SUPPLYING, INSTALLATION, TESTING & COMMISSIONING OF SITC OF 10, 15 & 20 HP SUBMERSIBLE PUMPSETS WITH NECESSARY COMPONENTS & ACCESSORIES AT VARIOUS WATER WORKS AT CHAKLASI NAGARPALIKA UNDER: 15TH FINANCE SCHEME.

SECTION-7 BILL OF QUANTITIES-285

Deduct _______ % below Rs. Rs.

Estimated Amount put to tender Rs.

Add _______ % above Rs. Rs.

Total Amount Rs.

Total Amount Rs.

*( Please strike out whichever is not applicable)

Note :1 All work shall be carried out as per Public Works Department Hand Book and other specifications of Division or as

Note :2 Rates quoted include clearance of site (prior commencement of work and its close) in all respects and hold good

for work under.

Note : 3 I/ We have read the conditions mentioned in this tender and agree to abide by the same.

Note : 4 In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.: PRC-

10/2017 Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C. items where

there is a change as per actual mix design the cost of difference of cement consumption have been deducted

from the rate of original item at the rate of input rate mentioned in all the tender.

Signature of Contractor Chief Officer

Chaklasi Nagarpalika

SECTION-7 BILL OF QUANTITIES-286

CHAKLASI MUNICIPALITY, CHAKLASI

S.I.T.C OF 15 HP SUBMERSIBLE PUMPING MACHINERY WITH ALL COMPONENTS & ACCESSORIES AT MAMO GOBRO AREA AT WARD 01 AT CHAKLASI.

Description of Items Qty. Unit Amount (Rs.)

Lifting of submersible motor pump set complete with required No .& size of casing pipes by means of proper chain pulley block and

pipe. wrenches. Job includes stacking of pipes chronologically after due checking of threads. Up to 60 mtrs. 1.00 Nos. 1711.95

S.I.T.C. submersible pump set for bore of 150 mm. dia. or, more having 3 phase motor capacity not more than 15 H.P. and discharge

2 capacity having, Lifting and Lowering taken extra. (8 stage) 695 to 492 L.P.M. at the head 48 to 73 mtrs suitable for 65/50 mm dia.

delivery pipe. Cat.III. 1.00 sets 49939.45

Lowering of submersible motor pump set at the depth of following, complete with required. Nos. and size of casing pipes erected by

3 means of proper chain pulley block & pipe wrenches after checking of threads of each pipe with coupling to take the load of the pump set

and pipe assembly filled up with water. Up to 60 mtrs. 1.00 Nos. 1711.95

Supplying & erecting approved make motor control cubical panel [Star delta] made from 16G CRCA sheet duly epoxy powder painted

inside and outside with hinged doors and locking with suitable size of ON - OFF isolator (AC 3 / 23 duty) main fuses. Digital volt and

current meter (in a single unit) with micro controller based control unit and current sensing single phasing preventer electronic overload

protection, over voltage (Programmable) protection and under voltage (Programmable) protection, prod less dry run protection

programming facility for setting of all parameter like overload current, high voltage limit, low voltage limit, dry run limit with digital indication

on seven segment LED display for any fault like over load, high voltage, low voltage, dry running single crimped, electronic star delta

timer, feather touch start / stop push buttons to be erected on angle iron frame. Grouted on wall the contactors will be of L& T, Siemens,

BCH make only). S/D up to 15 HP. 1.00 No 16053.95

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible Submersible copper cable approved make of following Size.

1 R x 3 Core x 4 Sq. mm. 80.00 Mtr. 146.45

1 R x 3 Core x 6 Sq. mm. 30.00 Mtr. 172.71

Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe Technology as

per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising, Inner

pipe dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded by highly

conductive compound with high charge dissipation suitable for following type of applications with chamber and heavy duty cover.

(A)(approved make OEM has to submit test certificate including value of earth resistance of installation duly stamped and signed by

agency and officer Incharge has to ensure the value of earthing resistane mentioned in test Certificate) & having back filling compound of

6 (B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no load &

dry form, Sulphar content:- <2%(C) Back fill Compound :- Earthing compound should be capable to retain moisture for long time

Necessary test report must be submitted by Agency. For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT panel board,

Motors etc. using proper clamp. 20.00 Kg. 97.00

SBD SECTION-7 BILL OF QUANTITIES-287

Description of Items Qty. Unit Amount (Rs.)

Providing & erecting motor protection circuit breaker with shock proof enclosure (IP 65) erected as per direction for following motor HP

phase 440V A.C. up to 15 HP 18 to 26 Amp. 1.00 No 5230.79

Providing Water proof straight Joint in PVC insulated flat flexible copper cable by using insulating material, water proofing material &

making the joint complete. Up to 10 Sq. mm. 4.00 No 189.88

10 Supplying of following size of HEAVY UPVC column pipe with coupler and wire lock. For 100mm. 30.50 Rmt. 1130.19

Providing and supplying in standard length ISI mark rigid unplasticised PVC pipes suitable for potable water with ring fit joint including cost

of rings, as per IS specification no. 4985/1988 including all local and central taxes, transportation, freight charges, octroi, inspection

11 charges, loading, unloading, conveyance to the departmental stores and including cost of jointing meterial etc. complete. Note : One

coupler / ring shall be provided with each full length pipe cost of which is included in rates below. Test Pressure 10 Kg/cm2. 110mm PVC

Pipes. 30.00 Rmt. 320.00

Lowering, laying, fixing and jointing PVC/uPVC/cPVC pipes and specials of following class and diameter including cost of conveyance

12 from stores to site of works including cost of labour, material, cement solvent, giving satisfactory hydraulic testing as per ISI code.

100/110mm Dia PVC Pipes 60.50 Rmt. 21.85

Supplying ISI Marked (Embossed) following size of Heavy duty “C” Class G.I. Pipe & erecting as directed by Engineer-in-charge with

necessary plumbing as desired. 100mm. 10.00 Rmt. 804.97

Providing and fixing flanged D.I.D.F. / Class K-9 pipes vertically for RCC. Reservoir incl. providing clamps at every 3 mt incl. jointing

materials such as nuts, bolts, rubber packing, hydraulic testing and necessary scaffolding etc. complete. 100mm. 30.00 Rmt. 2684.10

Supply of following size of TOP & BOTTOM accessories i.e. Adaptor set (CI) long, pump guard set, starter pipe Rubber ring for

submersible pump & UPVC column pipe as directed by Engineer - in - charge with necessary plumbing as desired. 100mm. 1.00 No 3872.34

16 Supplying & erecting G.l. bend for pipe connections suitable for 100mm. 1.00 No 548.43

Clamps made from MS plate with 3 holes on either side with nuts & bolts of standard make and suitable size. 450 mm X 65 mm X 10 mm

flat suitable to 100/125 mm dia. pipe. 1.00 No 693.94

Manufacture, Supply & Delivery of Ductile Iron Flange socket spigot bends, tees, reducers or any other specials as per BS-EN-545/1995

Class-A series K12 suitable for use with D.I. Pipes manufactured as per IS:8329/1994 delivery of specials is to be made to GWSSB store

18 or site of works any where in Gujarat including all taxes, loading, unloading, carting, stacking, insurance, inspection charges, octroi etc.

complete. With external bitumen & zinc coating & internal cement mortar lining. Socket & Spigot type. From 80 to 300mm Dia. Flange

Ended. 60.00 Kgs. 151.00

Supplying & erecting Mild Steel heavy duty Flanges with rubber packing and hardware materials for pipe connections suitable for 100mm.

SBD SECTION-7 BILL OF QUANTITIES-288

Description of Items Qty. Unit Amount (Rs.)

Providing and supplying at store or site of work incl. freight, loading, unloading, stacking, insaurance & all taxes etc. complete. P. V. C.

Tee (Moulded). 110 x 75 mm. 1.00 No 338.00

P. V. C. Reducer. 110 x 75 mm. 1.00 No 182.00

P. V. C. Bend 90° Moulded heavy. 110mm 1.00 No 519.00

Providing and Supplying ISI mark CI D/F Sluice valves, butterfly valves & Reflux valves of following class and diameter including all taxes,

insurance, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to departmental stores, stacking etc.

complete. Sluice valves as per IS - 780 & 2906 / 1984. Sluice Valve ISI Mark only. PN-1.6 With hand/wheel cap operated (Alt-1 type long

Excavation for pipe line trenches for water supply, sewerage line, manhole etc. all with shoring and struting if required as per required

22 gradient and line including safety provisions using site rails and stacking excavated stuff including up to all required lead cleaning the site

etc. complete for all lifts and strata as specified. In all sort of soil and soft murrum. Upto 1.50 Mt. Depth. 34.00 Cmt. 102.35

Lowering, laying and jointing in position following C. I. / D/F Reflux valves, Butterfly valves, Sluice valves and Air valves including cost of

all labour, jointing material, including nut bolts and giving satisfactory hydraulic testing, etc. complete. For 100mm Dia. 1.00 Nos 504.85

Construction of valves chambers in brick or bela stone masonry, locally available in C. M. 1:6. Foundation concrete 150 mm thick in C. C.

1:4:8 of trap metal size 25 mm to 40 mm thick, inside cement plaster in C. M. 1:3 and cement pointing outside in C. M. 1:3 and top cover

of precast RCC slab 100 mm thick (with key hole in two parts, each with handles or MS Bar etc. complete as given size) Upto 1 Mt. depth

24 from G. L. to pipe invert level incl. complete civil works but excl. cost of excavation and refilling, with cast in situ RCC slab in one single

piece with fixing of CI-MH Frame and cover (excl. cost of CI-MH Frame and cover) with 23 mm thick brick masonry wall in C.M.1:6. Size

of chamber 0.90 m x 0.90 m and 1.0 mt. deep. With precast slab in two parts 15 mm.

25 CI Frame & Cover For Valve Chamber 100.00 Kg. 58.00

Providing and casting in situ C.C. in grade M-20 (proportions as per mix design or as per table9 of IS456 2000 in masses by weigh

batching) using granite, quartzite trap metal of size 6 mm to 20 mm for RCC work, including scaffolding centering, formwork, needle

26 vibrated consolidation, curing complete up to 6 meter depth or height (excluding cost of reinforcement and neat finishing) with centering

and shuttering/deshuttering etc. complete for structure other than water retaining (Below G.L). For Thrust Block. With Form Work.

Refilling the pipeline trenches incl. ramming, watering, consolidating desposal of surplus stuff as directed within a radius of 3 km.

Supplying cutting, bending, binding and placing in position steel as per plan and design and as per ISS 2502 including cost of steel and

28 binding wire for reserviors/structures only including lift up to 6 meter height or depth below G.L. for all diameters. Do-Thermo mechanically

Treated (TMT) bars Fe-500 grade for all diameters. 20.00 Kgs 89.12

29 Compressor test of tube well by air compressor of 600 CFM / 150 PSI capacity in all districts. 2.00 Hour 3893.00

Labour charges for repairing leakage/ Jointing in CI/DI pipeline or Sluice Valve of following diameter at different places including

necessary excavation manually or by machinery, removing of mud, dewatering, cleaning of pipe, cutting of pipe, Jointing & repairing using

CID joints including CID joints, rubber rings, nut bolts, hiring excavator, Hydra/ Crane, dewatering machine, fuel, operator etc complete

(including cost of jointing material but excluding cost of pipe). 100mm. 2.00 No. 2068.85

SBD SECTION-7 BILL OF QUANTITIES-289

Description of Items Qty. Unit Amount (Rs.)

Labour charges for repairing of leakage/ Jointing in PVC pipeline of following dia meter at different places including necessary excavation

manually or by mechanise excavation, dewatering removing of mud, cleaning of pipe and leakage portion, cutting the pipeline & removing

piece of pipe from trench with inclusive of mechanical devices JCB, Hydra/Crain if necessary & labours required with providing material

such couplers, solution etc. comp. (incl. all material but Exclu. cost of pipe). 110mm. 2.00 No. 1124.70

Providing and fixing 50 cm wide M.S. Ladder fabricated from M.S. Flats 10 mm x 75mm with 20 mm dia steel bar steps in double rows, @

32 30 cm C/C. The include stays of 10 mm x 50 mm flats fixed at 3 meter C/C with welding anchoring and 3 coats anticorrosive paint.

Supply and installation of MS fabricated structure cabin @ site of work using 65 mm, 50 mm & 25 mm square pipes with cabin size

mtr x 1.5 mtr x 2.13 mtr including providing & fitting of (1) backalite sheet 3.5mm thick in sides, (2) 20 guage MS sheet outer side for side

walls, (3) backalite sheet 3.5 mm thick sheet for roof side, (4) 24 guage GI sheet out side with 15 mm plywood sandwitch fitting & flooring

33 with 19 mm water proof plywood sheet and (5) shock proof rubber mating. Job includes oil painting two coats, door locking handle

arrangement, providing proper air ventilation and fuse box. The meter & fuse box should be fitted on timber hold fast for holding screw or

nut bolts by semi skilled labour as per detailed technical specifications, drawings and instructions of the Engineer-in-charge.

Add 2% For Contengency Charges.

Add 1% For Labor Cess.

Total Project Cost Rs.

SBD SECTION-7 BILL OF QUANTITIES-290

CHAKLASI MUNICIPALITY, CHAKLASI

S.I.T.C OF 15 HP SUBMERSIBLE PUMPING MACHINERY WITH ALL COMPONENTS & ACCESSORIES AT SATODI NAKO HALU BHAGAT NO KUVO AT WARD 02 AT CHAKLASI.

Description of Items Qty. Unit Amount (Rs.)

Lifting of submersible motor pump set complete with required No .& size of casing pipes by means of proper chain pulley block and

pipe. wrenches. Job includes stacking of pipes chronologically after due checking of threads. Up to 60 mtrs. 1.00 Nos. 1711.95

S.I.T.C. submersible pump set for bore of 150 mm. dia. or, more having 3 phase motor capacity not more than 15 H.P. and discharge

2 capacity having, Lifting and Lowering taken extra. (8 stage) 695 to 492 L.P.M. at the head 48 to 73 mtrs suitable for 65/50 mm dia. delivery

pipe. Cat.III. 1.00 sets 49939.45

Lowering of submersible motor pump set at the depth of following, complete with required. Nos. and size of casing pipes erected by means

3 of proper chain pulley block & pipe wrenches after checking of threads of each pipe with coupling to take the load of the pump set and pipe

assembly filled up with water. Up to 60 mtrs. 1.00 Nos. 1711.95

Supplying & erecting approved make motor control cubical panel [Star delta] made from 16G CRCA sheet duly epoxy powder painted

inside and outside with hinged doors and locking with suitable size of ON - OFF isolator (AC 3 / 23 duty) main fuses. Digital volt and current

meter (in a single unit) with micro controller based control unit and current sensing single phasing preventer electronic overload protection,

over voltage (Programmable) protection and under voltage (Programmable) protection, prod less dry run protection programming facility for

setting of all parameter like overload current, high voltage limit, low voltage limit, dry run limit with digital indication on seven segment LED

display for any fault like over load, high voltage, low voltage, dry running single crimped, electronic star delta timer, feather touch start / stop

push buttons to be erected on angle iron frame. Grouted on wall the contactors will be of L& T, Siemens, BCH make only). S/D up to 15 HP.

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible Submersible copper cable approved make of following Size.

1 R x 3 Core x 4 Sq. mm. 80.00 Mtr. 146.45

1 R x 3 Core x 6 Sq. mm. 30.00 Mtr. 172.71

Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe Technology as

per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising, Inner

pipe dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded by highly

conductive compound with high charge dissipation suitable for following type of applications with chamber and heavy duty cover.

(A)(approved make OEM has to submit test certificate including value of earth resistance of installation duly stamped and signed by agency

and officer Incharge has to ensure the value of earthing resistane mentioned in test Certificate) & having back filling compound of (B) Inner

6 chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no load & dry form,

Sulphar content:- <2%(C) Back fill Compound :- Earthing compound should be capable to retain moisture for long time Necessary test

report must be submitted by Agency. For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT panel board, Motors

etc. using proper clamp. 20.00 Kg. 97.00

SBD SECTION-7 BILL OF QUANTITIES-291

Description of Items Qty. Unit Amount (Rs.)

Providing & erecting motor protection circuit breaker with shock proof enclosure (IP 65) erected as per direction for following motor HP

phase 440V A.C. up to 15 HP 18 to 26 Amp. 1.00 No 5230.79

Providing Water proof straight Joint in PVC insulated flat flexible copper cable by using insulating material, water proofing material & making

the joint complete. Up to 10 Sq. mm. 4.00 No 189.88

10 Supplying of following size of HEAVY UPVC column pipe with coupler and wire lock. For 100mm. 30.50 Rmt. 1130.19

Providing and supplying in standard length ISI mark rigid unplasticised PVC pipes suitable for potable water with ring fit joint including cost

of rings, as per IS specification no. 4985/1988 including all local and central taxes, transportation, freight charges, octroi, inspection

11 charges, loading, unloading, conveyance to the departmental stores and including cost of jointing meterial etc. complete. Note : One coupler

/ ring shall be provided with each full length pipe cost of which is included in rates below. Test Pressure 10 Kg/cm2. 110mm PVC Pipes.

Lowering, laying, fixing and jointing PVC/uPVC/cPVC pipes and specials of following class and diameter including cost of conveyance from

12 stores to site of works including cost of labour, material, cement solvent, giving satisfactory hydraulic testing as per ISI code. 100/110mm

Dia PVC Pipes 60.50 Rmt. 21.85

Supplying ISI Marked (Embossed) following size of Heavy duty “C” Class G.I. Pipe & erecting as directed by Engineer-in-charge with

necessary plumbing as desired. 100mm. 10.00 Rmt. 804.97

Providing and fixing flanged D.I.D.F. / Class K-9 pipes vertically for RCC. Reservoir incl. providing clamps at every 3 mt incl. jointing

materials such as nuts, bolts, rubber packing, hydraulic testing and necessary scaffolding etc. complete. 100mm. 30.00 Rmt. 2684.10

Supply of following size of TOP & BOTTOM accessories i.e. Adaptor set (CI) long, pump guard set, starter pipe Rubber ring for submersible

pump & UPVC column pipe as directed by Engineer - in - charge with necessary plumbing as desired. 100mm. 1.00 No 3872.34

16 Supplying & erecting G.l. bend for pipe connections suitable for 100mm. 1.00 No 548.43

Clamps made from MS plate with 3 holes on either side with nuts & bolts of standard make and suitable size. 450 mm X 65 mm X 10 mm

flat suitable to 100/125 mm dia. pipe. 1.00 No 693.94

Manufacture, Supply & Delivery of Ductile Iron Flange socket spigot bends, tees, reducers or any other specials as per BS-EN-545/1995

Class-A series K12 suitable for use with D.I. Pipes manufactured as per IS:8329/1994 delivery of specials is to be made to GWSSB store or

18 site of works any where in Gujarat including all taxes, loading, unloading, carting, stacking, insurance, inspection charges, octroi etc.

complete. With external bitumen & zinc coating & internal cement mortar lining. Socket & Spigot type. From 80 to 300mm Dia. Flange

Ended. 60.00 Kgs. 151.00

Supplying & erecting Mild Steel heavy duty Flanges with rubber packing and hardware materials for pipe connections suitable for 100mm.

SBD SECTION-7 BILL OF QUANTITIES-292

Description of Items Qty. Unit Amount (Rs.)

Providing and supplying at store or site of work incl. freight, loading, unloading, stacking, insaurance & all taxes etc. complete. P. V. C. Tee

(Moulded). 110 x 75 mm. 1.00 No 338.00

P. V. C. Reducer. 110 x 75 mm. 1.00 No 182.00

P. V. C. Bend 90° Moulded heavy. 110mm 1.00 No 519.00

Providing and Supplying ISI mark CI D/F Sluice valves, butterfly valves & Reflux valves of following class and diameter including all taxes,

insurance, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to departmental stores, stacking etc.

complete. Sluice valves as per IS - 780 & 2906 / 1984. Sluice Valve ISI Mark only. PN-1.6 With hand/wheel cap operated (Alt-1 type long

Excavation for pipe line trenches for water supply, sewerage line, manhole etc. all with shoring and struting if required as per required

22 gradient and line including safety provisions using site rails and stacking excavated stuff including up to all required lead cleaning the site

etc. complete for all lifts and strata as specified. In all sort of soil and soft murrum. Upto 1.50 Mt. Depth. 34.00 Cmt. 102.35

Lowering, laying and jointing in position following C. I. / D/F Reflux valves, Butterfly valves, Sluice valves and Air valves including cost of all

labour, jointing material, including nut bolts and giving satisfactory hydraulic testing, etc. complete. For 100mm Dia. 1.00 Nos 504.85

Construction of valves chambers in brick or bela stone masonry, locally available in C. M. 1:6. Foundation concrete 150 mm thick in C. C.

1:4:8 of trap metal size 25 mm to 40 mm thick, inside cement plaster in C. M. 1:3 and cement pointing outside in C. M. 1:3 and top cover of

precast RCC slab 100 mm thick (with key hole in two parts, each with handles or MS Bar etc. complete as given size) Upto 1 Mt. depth from

G. L. to pipe invert level incl. complete civil works but excl. cost of excavation and refilling, with cast in situ RCC slab in one single piece with

fixing of CI-MH Frame and cover (excl. cost of CI-MH Frame and cover) with 23 mm thick brick masonry wall in C.M.1:6. Size of chamber

0.90 m x 0.90 m and 1.0 mt. deep. With precast slab in two parts 15 mm. 1.00 Nos 8898.70

25 CI Frame & Cover For Valve Chamber 100.00 Kg. 58.00

Providing and casting in situ C.C. in grade M-20 (proportions as per mix design or as per table9 of IS456 2000 in masses by weigh

batching) using granite, quartzite trap metal of size 6 mm to 20 mm for RCC work, including scaffolding centering, formwork, needle

26 vibrated consolidation, curing complete up to 6 meter depth or height (excluding cost of reinforcement and neat finishing) with centering and

shuttering/deshuttering etc. complete for structure other than water retaining (Below G.L). For Thrust Block. With Form Work.

27 Refilling the pipeline trenches incl. ramming, watering, consolidating desposal of surplus stuff as directed within a radius of 3 km. 34.00 Cmt. 25.30

Supplying cutting, bending, binding and placing in position steel as per plan and design and as per ISS 2502 including cost of steel and

28 binding wire for reserviors/structures only including lift up to 6 meter height or depth below G.L. for all diameters. Do-Thermo mechanically

Treated (TMT) bars Fe-500 grade for all diameters. 20.00 Kgs 89.12

29 Compressor test of tube well by air compressor of 600 CFM / 150 PSI capacity in all districts. 2.00 Hour 3893.00

Labour charges for repairing leakage/ Jointing in CI/DI pipeline or Sluice Valve of following diameter at different places including necessary

excavation manually or by machinery, removing of mud, dewatering, cleaning of pipe, cutting of pipe, Jointing & repairing using CID joints

including CID joints, rubber rings, nut bolts, hiring excavator, Hydra/ Crane, dewatering machine, fuel, operator etc complete (including cost

of jointing material but excluding cost of pipe). 100mm. 2.00 No. 2068.85

SBD SECTION-7 BILL OF QUANTITIES-293

Description of Items Qty. Unit Amount (Rs.)

Labour charges for repairing of leakage/ Jointing in PVC pipeline of following dia meter at different places including necessary excavation

manually or by mechanise excavation, dewatering removing of mud, cleaning of pipe and leakage portion, cutting the pipeline & removing

piece of pipe from trench with inclusive of mechanical devices JCB, Hydra/Crain if necessary & labours required with providing material

such couplers, solution etc. comp. (incl. all material but Exclu. cost of pipe). 110mm. 2.00 No. 1124.70

Providing and fixing 50 cm wide M.S. Ladder fabricated from M.S. Flats 10 mm x 75mm with 20 mm dia steel bar steps in double rows, @

32 30 cm C/C. The include stays of 10 mm x 50 mm flats fixed at 3 meter C/C with welding anchoring and 3 coats anticorrosive paint.

Supply and installation of MS fabricated structure cabin @ site of work using 65 mm, 50 mm & 25 mm square pipes with cabin size 1.5 mtr

x 1.5 mtr x 2.13 mtr including providing & fitting of (1) backalite sheet 3.5mm thick in sides, (2) 20 guage MS sheet outer side for side walls,

(3) backalite sheet 3.5 mm thick sheet for roof side, (4) 24 guage GI sheet out side with 15 mm plywood sandwitch fitting & flooring with

33 mm water proof plywood sheet and (5) shock proof rubber mating. Job includes oil painting two coats, door locking handle arrangement,

providing proper air ventilation and fuse box. The meter & fuse box should be fitted on timber hold fast for holding screw or nut bolts by

semi skilled labour as per detailed technical specifications, drawings and instructions of the Engineer-in-charge.

(Electro. Mech SOR, Section A, It.No. 13, Pg. 22)

Add 2% For Contengency Charges.

Add 1% For Labor Cess.

Total Project Cost Rs.

SBD SECTION-7 BILL OF QUANTITIES-294

CHAKLASI MUNICIPALITY, CHAKLASI

S.I.T.C OF 15 HP SUBMERSIBLE PUMPING MACHINERY WITH ALL COMPONENTS & ACCESSORIES AT RAMPURA SATODIYA NAKU (TIKUBHAI) AT WARD 02 AT CHAKLASI.

Description of Items Qty. Unit Amount (Rs.)

Lifting of submersible motor pump set complete with required No .& size of casing pipes by means of proper chain pulley block and

pipe. wrenches. Job includes stacking of pipes chronologically after due checking of threads. Up to 60 mtrs. 1.00 Nos. 1711.95

S.I.T.C. submersible pump set for bore of 150 mm. dia. or, more having 3 phase motor capacity not more than 15 H.P. and discharge

2 capacity having, Lifting and Lowering taken extra. (8 stage) 695 to 492 L.P.M. at the head 48 to 73 mtrs suitable for 65/50 mm dia.

delivery pipe. Cat.III. 1.00 sets 49939.45

Lowering of submersible motor pump set at the depth of following, complete with required. Nos. and size of casing pipes erected by

3 means of proper chain pulley block & pipe wrenches after checking of threads of each pipe with coupling to take the load of the pump

set and pipe assembly filled up with water. Up to 60 mtrs. 1.00 Nos. 1711.95

Supplying & erecting approved make motor control cubical panel [Star delta] made from 16G CRCA sheet duly epoxy powder painted

inside and outside with hinged doors and locking with suitable size of ON - OFF isolator (AC 3 / 23 duty) main fuses. Digital volt and

current meter (in a single unit) with micro controller based control unit and current sensing single phasing preventer electronic overload

protection, over voltage (Programmable) protection and under voltage (Programmable) protection, prod less dry run protection

programming facility for setting of all parameter like overload current, high voltage limit, low voltage limit, dry run limit with digital

indication on seven segment LED display for any fault like over load, high voltage, low voltage, dry running single crimped, electronic

star delta timer, feather touch start / stop push buttons to be erected on angle iron frame. Grouted on wall the contactors will be of L&

T, Siemens, BCH make only). S/D up to 15 HP. 1.00 No 16053.95

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible Submersible copper cable approved make of following

1 R x 3 Core x 4 Sq. mm. 80.00 Mtr. 146.45

1 R x 3 Core x 6 Sq. mm. 30.00 Mtr. 172.71

Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe Technology

as per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising,

Inner pipe dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded

by highly conductive compound with high charge dissipation suitable for following type of applications with chamber and heavy duty

cover. (A)(approved make OEM has to submit test certificate including value of earth resistance of installation duly stamped and

signed by agency and officer Incharge has to ensure the value of earthing resistane mentioned in test Certificate) & having back filling

6 compound of (B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017, Voltage drop:- <

volt at no load & dry form, Sulphar content:- <2%(C) Back fill Compound :- Earthing compound should be capable to retain moisture for

long time Necessary test report must be submitted by Agency. For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

SBD SECTION-7 BILL OF QUANTITIES-295

Description of Items Qty. Unit Amount (Rs.)

Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT panel board,

Motors etc. using proper clamp. 20.00 Kg. 97.00

Providing & erecting motor protection circuit breaker with shock proof enclosure (IP 65) erected as per direction for following motor HP

3 phase 440V A.C. up to 15 HP 18 to 26 Amp. 1.00 No 5230.79

Providing Water proof straight Joint in PVC insulated flat flexible copper cable by using insulating material, water proofing material &

making the joint complete. Up to 10 Sq. mm. 4.00 No 189.88

10 Supplying of following size of HEAVY UPVC column pipe with coupler and wire lock. For 100mm. 30.50 Rmt. 1130.19

Lowering, laying, fixing and jointing PVC/uPVC/cPVC pipes and specials of following class and diameter including cost of conveyance

11 from stores to site of works including cost of labour, material, cement solvent, giving satisfactory hydraulic testing as per ISI code.

100/110mm Dia PVC Pipes. 30.50 Rmt. 21.85

Supplying ISI Marked (Embossed) following size of Heavy duty “C” Class G.I. Pipe & erecting as directed by Engineer-in-charge with

necessary plumbing as desired. 100mm. 10.00 Rmt. 804.97

Supply of following size of TOP & BOTTOM accessories i.e. Adaptor set (CI) long, pump guard set, starter pipe Rubber ring for

submersible pump & UPVC column pipe as directed by Engineer - in - charge with necessary plumbing as desired. 100mm. 1.00 No 3872.34

14 Supplying & erecting G.l. bend for pipe connections suitable for 100mm. 1.00 No 548.43

Clamps made from MS plate with 3 holes on either side with nuts & bolts of standard make and suitable size. 450 mm X 65 mm X

mm flat suitable to 100/125 mm dia. pipe. 1.00 No 693.94

Supplying & erecting Mild Steel heavy duty Flanges with rubber packing and hardware materials for pipe connections suitable for

Providing and supplying at store or site of work incl. freight, loading, unloading, stacking, insaurance & all taxes etc. complete. P. V. C.

Tee (Moulded). 110 x 75 mm. 1.00 No 338.00

P. V. C. Reducer. 110 x 75 mm. 1.00 No 182.00

P. V. C. Bend 90° Moulded heavy. 110mm 1.00 No 519.00

Providing and Supplying ISI mark CI D/F Sluice valves, butterfly valves & Reflux valves of following class and diameter including all

taxes, insurance, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to departmental stores,

stacking etc. complete. Sluice valves as per IS - 780 & 2906 / 1984. Sluice Valve ISI Mark only. PN-1.6 With hand/wheel cap operated

(Alt-1 type long body). 80mm. 1.00 Nos. 2946.00

Excavation for pipe line trenches for water supply, sewerage line, manhole etc. all with shoring and struting if required as per required

19 gradient and line including safety provisions using site rails and stacking excavated stuff including up to all required lead cleaning the

site etc. complete for all lifts and strata as specified. In all sort of soil and soft murrum. Upto 1.50 Mt. Depth. 10.00 Cmt. 102.35

Lowering, laying and jointing in position following C. I. / D/F Reflux valves, Butterfly valves, Sluice valves and Air valves including cost

20 of all labour, jointing material, including nut bolts and giving satisfactory hydraulic testing, etc. complete. For 80mm Dia.

SBD SECTION-7 BILL OF QUANTITIES-296

Description of Items Qty. Unit Amount (Rs.)

Providing and casting in situ C.C. in grade M-20 (proportions as per mix design or as per table9 of IS456 2000 in masses by weigh

batching) using granite, quartzite trap metal of size 6 mm to 20 mm for RCC work, including scaffolding centering, formwork, needle

21 vibrated consolidation, curing complete up to 6 meter depth or height (excluding cost of reinforcement and neat finishing) with

centering and shuttering/deshuttering etc. complete for structure other than water retaining (Below G.L). For Thrust Block. With Form

Work. 0.50 Cmt. 6348.00

Refilling the pipeline trenches incl. ramming, watering, consolidating desposal of surplus stuff as directed within a radius of 3 km.

Supplying cutting, bending, binding and placing in position steel as per plan and design and as per ISS 2502 including cost of steel and

23 binding wire for reserviors/structures only including lift up to 6 meter height or depth below G.L. for all diameters. Do-Thermo

mechanically Treated (TMT) bars Fe-500 grade for all diameters. 20.00 Kgs 89.12

24 Compressor test of tube well by air compressor of 600 CFM / 150 PSI capacity in all districts. 2.00 Hour 3893.00

Labour charges for repairing leakage/ Jointing in CI/DI pipeline or Sluice Valve of following diameter at different places including

necessary excavation manually or by machinery, removing of mud, dewatering, cleaning of pipe, cutting of pipe, Jointing & repairing

using CID joints including CID joints, rubber rings, nut bolts, hiring excavator, Hydra/ Crane, dewatering machine, fuel, operator etc

complete (including cost of jointing material but excluding cost of pipe). 75mm. 2.00 No. 1828.50

Supply and installation of MS fabricated structure cabin @ site of work using 65 mm, 50 mm & 25 mm square pipes with cabin size

mtr x 1.5 mtr x 2.13 mtr including providing & fitting of (1) backalite sheet 3.5mm thick in sides, (2) 20 guage MS sheet outer side for

side walls, (3) backalite sheet 3.5 mm thick sheet for roof side, (4) 24 guage GI sheet out side with 15 mm plywood sandwitch fitting &

26 flooring with 19 mm water proof plywood sheet and (5) shock proof rubber mating. Job includes oil painting two coats, door locking

handle arrangement, providing proper air ventilation and fuse box. The meter & fuse box should be fitted on timber hold fast for holding

screw or nut bolts by semi skilled labour as per detailed technical specifications, drawings and instructions of the Engineer-in-charge.

Add 2% For Contengency Charges.

Add 1% For Labor Cess.

Total Project Cost Rs.

SBD SECTION-7 BILL OF QUANTITIES-297

CHAKLASI MUNICIPALITY, CHAKLASI

S.I.T.C OF 15 HP SUBMERSIBLE PUMPING MACHINERY WITH ALL COMPONENTS & ACCESSORIES AT MOTAKUVA AT WARD 02 AT CHAKLASI.

Description of Items Qty. Unit Amount (Rs.)

Lifting of submersible motor pump set complete with required No .& size of casing pipes by means of proper chain pulley block and

pipe. wrenches. Job includes stacking of pipes chronologically after due checking of threads. Up to 60 mtrs. 1.00 Nos. 1711.95

S.I.T.C. submersible pump set for bore of 150 mm. dia. or, more having 3 phase motor capacity not more than 15 H.P. and discharge

2 capacity having, Lifting and Lowering taken extra. (8 stage) 695 to 492 L.P.M. at the head 48 to 73 mtrs suitable for 65/50 mm dia.

delivery pipe. Cat.III. 1.00 sets 49939.45

Lowering of submersible motor pump set at the depth of following, complete with required. Nos. and size of casing pipes erected by

3 means of proper chain pulley block & pipe wrenches after checking of threads of each pipe with coupling to take the load of the pump

set and pipe assembly filled up with water. Up to 60 mtrs. 1.00 Nos. 1711.95

Supplying & erecting approved make motor control cubical panel [Star delta] made from 16G CRCA sheet duly epoxy powder painted

inside and outside with hinged doors and locking with suitable size of ON - OFF isolator (AC 3 / 23 duty) main fuses. Digital volt and

current meter (in a single unit) with micro controller based control unit and current sensing single phasing preventer electronic overload

protection, over voltage (Programmable) protection and under voltage (Programmable) protection, prod less dry run protection

programming facility for setting of all parameter like overload current, high voltage limit, low voltage limit, dry run limit with digital

indication on seven segment LED display for any fault like over load, high voltage, low voltage, dry running single crimped, electronic

star delta timer, feather touch start / stop push buttons to be erected on angle iron frame. Grouted on wall the contactors will be of L& T,

Siemens, BCH make only). S/D up to 15 HP. 1.00 No 16053.95

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible Submersible copper cable approved make of following

1 R x 3 Core x 4 Sq. mm. 80.00 Mtr. 146.45

1 R x 3 Core x 6 Sq. mm. 30.00 Mtr. 172.71

Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe Technology

as per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising,

Inner pipe dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded by

highly conductive compound with high charge dissipation suitable for following type of applications with chamber and heavy duty cover.

(A)(approved make OEM has to submit test certificate including value of earth resistance of installation duly stamped and signed by

agency and officer Incharge has to ensure the value of earthing resistane mentioned in test Certificate) & having back filling compound

6 of (B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no load

& dry form, Sulphar content:- <2%(C) Back fill Compound :- Earthing compound should be capable to retain moisture for long time

Necessary test report must be submitted by Agency. For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT panel board,

Motors etc. using proper clamp. 20.00 Kg. 97.00

SBD SECTION-7 BILL OF QUANTITIES-299

Description of Items Qty. Unit Amount (Rs.)

Providing & erecting motor protection circuit breaker with shock proof enclosure (IP 65) erected as per direction for following motor HP

3 phase 440V A.C. up to 15 HP 18 to 26 Amp. 1.00 No 5230.79

Providing Water proof straight Joint in PVC insulated flat flexible copper cable by using insulating material, water proofing material &

making the joint complete. Up to 10 Sq. mm. 4.00 No 189.88

10 Supplying of following size of HEAVY UPVC column pipe with coupler and wire lock. For 100mm. 30.50 Rmt. 1130.19

Lowering, laying, fixing and jointing PVC/uPVC/cPVC pipes and specials of following class and diameter including cost of conveyance

11 from stores to site of works including cost of labour, material, cement solvent, giving satisfactory hydraulic testing as per ISI code.

100/110mm Dia PVC Pipes. 30.50 Rmt. 21.85

Supplying ISI Marked (Embossed) following size of Heavy duty “C” Class G.I. Pipe & erecting as directed by Engineer-in-charge with

necessary plumbing as desired. 100mm. 10.00 Rmt. 804.97

Supply of following size of TOP & BOTTOM accessories i.e. Adaptor set (CI) long, pump guard set, starter pipe Rubber ring for

submersible pump & UPVC column pipe as directed by Engineer - in - charge with necessary plumbing as desired. 100mm. 1.00 No 3872.34

14 Supplying & erecting G.l. bend for pipe connections suitable for 100mm. 1.00 No 548.43

Clamps made from MS plate with 3 holes on either side with nuts & bolts of standard make and suitable size. 450 mm X 65 mm X

mm flat suitable to 100/125 mm dia. pipe. 1.00 No 693.94

Supplying & erecting Mild Steel heavy duty Flanges with rubber packing and hardware materials for pipe connections suitable for

Providing and supplying at store or site of work incl. freight, loading, unloading, stacking, insaurance & all taxes etc. complete. P. V. C.

Tee (Moulded). 110 x 75 mm. 1.00 No 338.00

P. V. C. Reducer. 110 x 75 mm. 1.00 No 182.00

P. V. C. Bend 90° Moulded heavy. 110mm 1.00 No 519.00

Providing and Supplying ISI mark CI D/F Sluice valves, butterfly valves & Reflux valves of following class and diameter including all

taxes, insurance, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to departmental stores,

stacking etc. complete. Sluice valves as per IS - 780 & 2906 / 1984. Sluice Valve ISI Mark only. PN-1.6 With hand/wheel cap operated

(Alt-1 type long body). 80mm. 1.00 Nos. 2946.00

Excavation for pipe line trenches for water supply, sewerage line, manhole etc. all with shoring and struting if required as per required

19 gradient and line including safety provisions using site rails and stacking excavated stuff including up to all required lead cleaning the

site etc. complete for all lifts and strata as specified. In all sort of soil and soft murrum. Upto 1.50 Mt. Depth. 10.00 Cmt. 102.35

SBD SECTION-7 BILL OF QUANTITIES-300

Description of Items Qty. Unit Amount (Rs.)

Lowering, laying and jointing in position following C. I. / D/F Reflux valves, Butterfly valves, Sluice valves and Air valves including cost of

all labour, jointing material, including nut bolts and giving satisfactory hydraulic testing, etc. complete. For 80mm Dia. 1.00 Nos 460.00

Providing and casting in situ C.C. in grade M-20 (proportions as per mix design or as per table9 of IS456 2000 in masses by weigh

batching) using granite, quartzite trap metal of size 6 mm to 20 mm for RCC work, including scaffolding centering, formwork, needle

21 vibrated consolidation, curing complete up to 6 meter depth or height (excluding cost of reinforcement and neat finishing) with centering

and shuttering/deshuttering etc. complete for structure other than water retaining (Below G.L). For Thrust Block. With Form Work.

Refilling the pipeline trenches incl. ramming, watering, consolidating desposal of surplus stuff as directed within a radius of 3 km.

Supplying cutting, bending, binding and placing in position steel as per plan and design and as per ISS 2502 including cost of steel and

23 binding wire for reserviors/structures only including lift up to 6 meter height or depth below G.L. for all diameters. Do-Thermo

mechanically Treated (TMT) bars Fe-500 grade for all diameters. 20.00 Kgs 89.12

24 Compressor test of tube well by air compressor of 600 CFM / 150 PSI capacity in all districts. 2.00 Hour 3893.00

Labour charges for repairing leakage/ Jointing in CI/DI pipeline or Sluice Valve of following diameter at different places including

necessary excavation manually or by machinery, removing of mud, dewatering, cleaning of pipe, cutting of pipe, Jointing & repairing

using CID joints including CID joints, rubber rings, nut bolts, hiring excavator, Hydra/ Crane, dewatering machine, fuel, operator etc

complete (including cost of jointing material but excluding cost of pipe). 75mm. 2.00 No. 1828.50

Supply and installation of MS fabricated structure cabin @ site of work using 65 mm, 50 mm & 25 mm square pipes with cabin size

mtr x 1.5 mtr x 2.13 mtr including providing & fitting of (1) backalite sheet 3.5mm thick in sides, (2) 20 guage MS sheet outer side for

side walls, (3) backalite sheet 3.5 mm thick sheet for roof side, (4) 24 guage GI sheet out side with 15 mm plywood sandwitch fitting &

26 flooring with 19 mm water proof plywood sheet and (5) shock proof rubber mating. Job includes oil painting two coats, door locking

handle arrangement, providing proper air ventilation and fuse box. The meter & fuse box should be fitted on timber hold fast for holding

screw or nut bolts by semi skilled labour as per detailed technical specifications, drawings and instructions of the Engineer-in-charge.

Add 2% For Contengency Charges.

Add 1% For Labor Cess.

Total Project Cost Rs.

SBD SECTION-7 BILL OF QUANTITIES-301

CHAKLASI MUNICIPALITY, CHAKLASI

S.I.T.C OF 10 HP SUBMERSIBLE PUMPING MACHINERY WITH ALL COMPONENTS & ACCESSORIES AT MOTINAGAR AT WARD 03 AT CHAKLASI.

Description of Items Qty. Unit Amount (Rs.)

Lifting of submersible motor pump set complete with required No .& size of casing pipes by means of proper chain pulley block and

pipe. wrenches. Job includes stacking of pipes chronologically after due checking of threads. Up to 60 mtrs. 1.00 Nos. 1711.95

S.I.T.C. submersible pump set for bore of 150 mm. dia. or, more having 3 phase motor capacity not more than 10 H.P. and discharge

2 capacity having, Lifting and Lowering taken extra. 10 stage 575 to 480 LPM discharge at 60 to 70 mtr head for 65 mm dia delivery pipe.

Cat.III. 1.00 sets 39659.67

Lowering of submersible motor pump set at the depth of following, complete with required. Nos. and size of casing pipes erected by

3 means of proper chain pulley block & pipe wrenches after checking of threads of each pipe with coupling to take the load of the pump

set and pipe assembly filled up with water. Up to 60 mtrs. 1.00 Nos. 1711.95

Supplying & erecting approved make motor control cubical panel [Star delta] made from 16G CRCA sheet duly epoxy powder painted

inside and outside with hinged doors and locking with suitable size of ON - OFF isolator (AC 3 / 23 duty) main fuses. Digital volt and

current meter (in a single unit) with micro controller based control unit and current sensing single phasing preventer electronic overload

protection, over voltage (Programmable) protection and under voltage (Programmable) protection, prod less dry run protection

programming facility for setting of all parameter like overload current, high voltage limit, low voltage limit, dry run limit with digital

indication on seven segment LED display for any fault like over load, high voltage, low voltage, dry running single crimped, electronic

star delta timer, feather touch start / stop push buttons to be erected on angle iron frame. Grouted on wall the contactors will be of L& T,

Siemens, BCH make only). S/D up to 10 HP. 1.00 No 13794.58

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible Submersible copper cable approved make of following

1 R x 3 Core x 2.5 Sq. mm. 80.00 Mtr. 104.03

1 R x 3 Core x 4 Sq. mm. 30.00 Mtr. 146.45

Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe Technology

as per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising,

Inner pipe dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded by

highly conductive compound with high charge dissipation suitable for following type of applications with chamber and heavy duty cover.

(A)(approved make OEM has to submit test certificate including value of earth resistance of installation duly stamped and signed by

agency and officer Incharge has to ensure the value of earthing resistane mentioned in test Certificate) & having back filling compound

6 of (B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no load

& dry form, Sulphar content:- <2%(C) Back fill Compound :- Earthing compound should be capable to retain moisture for long time

Necessary test report must be submitted by Agency. For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT panel board,

Motors etc. using proper clamp. 20.00 Kg. 97.00

SBD SECTION-7 BILL OF QUANTITIES-302

Description of Items Qty. Unit Amount (Rs.)

Providing & erecting motor protection circuit breaker with shock proof enclosure (IP 65) erected as per direction for following motor HP

3 phase 440V A.C. up to 7.5 HP / 10 HP 12 to 18 Amp. 1.00 No 4803.56

Providing Water proof straight Joint in PVC insulated flat flexible copper cable by using insulating material, water proofing material &

making the joint complete. Up to 10 Sq. mm. 4.00 No 189.88

10 Supplying of following size of HEAVY UPVC column pipe with coupler and wire lock. For 80mm. 30.50 Rmt. 698.92

Providing and supplying in standard length ISI mark rigid unplasticised PVC pipes suitable for potable water with ring fit joint including

cost of rings, as per IS specification no. 4985/1988 including all local and central taxes, transportation, freight charges, octroi,

11 inspection charges, loading, unloading, conveyance to the departmental stores and including cost of jointing meterial etc. complete.

Note : One coupler / ring shall be provided with each full length pipe cost of which is included in rates below. Test Pressure 10 Kg/cm2

110mm PVC Pipes. 30.00 Rmt. 320.00

Lowering, laying, fixing and jointing PVC/uPVC/cPVC pipes and specials of following class and diameter including cost of conveyance

12 from stores to site of works including cost of labour, material, cement solvent, giving satisfactory hydraulic testing as per ISI code.

80/75mm Dia PVC Pipes 30.50 Rmt. 17.25

100/110mm Dia PVC Pipe 30.00 Rmt. 21.85

Supplying ISI Marked (Embossed) following size of Heavy duty “C” Class G.I. Pipe & erecting as directed by Engineer-in-charge with

necessary plumbing as desired. 100mm. 10.00 Rmt. 804.97

Supply of following size of TOP & BOTTOM accessories i.e. Adaptor set (CI) long, pump guard set, starter pipe Rubber ring for

submersible pump & UPVC column pipe as directed by Engineer - in - charge with necessary plumbing as desired. 80mm. 1.00 No 2681.55

15 Supplying & erecting G.l. bend for pipe connections suitable for 100mm. 1.00 No 548.43

Clamps made from MS plate with 3 holes on either side with nuts & bolts of standard make and suitable size. 450 mm X 65 mm X

mm flat suitable to 65/80 mm dia. pipe. 1.00 No 574.79

Manufacture, Supply & Delivery of Ductile Iron Flange socket spigot bends, tees, reducers or any other specials as per BS-EN-

545/1995 Class-A series K12 suitable for use with D.I. Pipes manufactured as per IS:8329/1994 delivery of specials is to be made to

17 GWSSB store or site of works any where in Gujarat including all taxes, loading, unloading, carting, stacking, insurance, inspection

charges, octroi etc. complete. With external bitumen & zinc coating & internal cement mortar lining. Socket & Spigot type. From 80 to

300mm Dia. Flange Ended. 30.00 Kgs. 151.00

Supplying & erecting Mild Steel heavy duty Flanges with rubber packing and hardware materials for pipe connections suitable for

Providing and supplying at store or site of work incl. freight, loading, unloading, stacking, insaurance & all taxes etc. complete. P. V. C.

Tee (Moulded). 110 x 75 mm. 1.00 No 338.00

P. V. C. Reducer. 110 x 75 mm. 1.00 No 182.00

P. V. C. Bend 90° Moulded heavy. 110mm 1.00 No 519.00

Providing and Supplying ISI mark CI D/F Sluice valves, butterfly valves & Reflux valves of following class and diameter including all

taxes, insurance, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to departmental stores,

stacking etc. complete. Sluice valves as per IS - 780 & 2906 / 1984. Sluice Valve ISI Mark only. PN-1.6 With hand/wheel cap operated

(Alt-1 type long body). 100mm. 1.00 Nos. 3902.00

SBD SECTION-7 BILL OF QUANTITIES-303

Description of Items Qty. Unit Amount (Rs.)

Excavation for pipe line trenches for water supply, sewerage line, manhole etc. all with shoring and struting if required as per required

21 gradient and line including safety provisions using site rails and stacking excavated stuff including up to all required lead cleaning the

site etc. complete for all lifts and strata as specified. In all sort of soil and soft murrum. Upto 1.50 Mt. Depth. 5.00 Cmt. 102.35

Lowering, laying and jointing in position following C. I. / D/F Reflux valves, Butterfly valves, Sluice valves and Air valves including cost of

22 all labour, jointing material, including nut bolts and giving satisfactory hydraulic testing, etc. complete. For 100mm Dia.

Construction of valves chambers in brick or bela stone masonry, locally available in C. M. 1:6. Foundation concrete 150 mm thick in C.

C. 1:4:8 of trap metal size 25 mm to 40 mm thick, inside cement plaster in C. M. 1:3 and cement pointing outside in C. M. 1:3 and top

cover of precast RCC slab 100 mm thick (with key hole in two parts, each with handles or MS Bar etc. complete as given size) Upto

23 Mt. depth from G. L. to pipe invert level incl. complete civil works but excl. cost of excavation and refilling, with cast in situ RCC slab in

one single piece with fixing of CI-MH Frame and cover (excl. cost of CI-MH Frame and cover) with 23 mm thick brick masonry wall in

C.M.1:6. Size of chamber 0.90 m x 0.90 m and 1.0 mt. deep. With precast slab in two parts 15 mm.

24 CI Frame & Cover For Valve Chamber 100.00 Kg. 58.00

Providing and casting in situ C.C. in grade M-20 (proportions as per mix design or as per table9 of IS456 2000 in masses by weigh

batching) using granite, quartzite trap metal of size 6 mm to 20 mm for RCC work, including scaffolding centering, formwork, needle

25 vibrated consolidation, curing complete up to 6 meter depth or height (excluding cost of reinforcement and neat finishing) with centering

and shuttering/deshuttering etc. complete for structure other than water retaining (Below G.L). For Thrust Block. With Form Work.

Refilling the pipeline trenches incl. ramming, watering, consolidating desposal of surplus stuff as directed within a radius of 3 km.

Supplying cutting, bending, binding and placing in position steel as per plan and design and as per ISS 2502 including cost of steel and

27 binding wire for reserviors/structures only including lift up to 6 meter height or depth below G.L. for all diameters. Do-Thermo

mechanically Treated (TMT) bars Fe-500 grade for all diameters. 20.00 Kgs 89.12

28 Compressor test of tube well by air compressor of 600 CFM / 150 PSI capacity in all districts. 2.00 Hour 3893.00

Labour charges for repairing leakage/ Jointing in CI/DI pipeline or Sluice Valve of following diameter at different places including

necessary excavation manually or by machinery, removing of mud, dewatering, cleaning of pipe, cutting of pipe, Jointing & repairing

using CID joints including CID joints, rubber rings, nut bolts, hiring excavator, Hydra/ Crane, dewatering machine, fuel, operator etc

complete (including cost of jointing material but excluding cost of pipe). 100mm. 2.00 No. 2068.85

Labour charges for repairing of leakage/ Jointing in PVC pipeline of following dia meter at different places including necessary

excavation manually or by mechanise excavation, dewatering removing of mud, cleaning of pipe and leakage portion, cutting the

pipeline & removing piece of pipe from trench with inclusive of mechanical devices JCB, Hydra/Crain if necessary & labours required

with providing material such couplers, solution etc. comp. (incl. all material but Exclu. cost of pipe). 110mm. 2.00 No. 1124.70

SBD SECTION-7 BILL OF QUANTITIES-304

Description of Items Qty. Unit Amount (Rs.)

Supply and installation of MS fabricated structure cabin @ site of work using 65 mm, 50 mm & 25 mm square pipes with cabin size

mtr x 1.5 mtr x 2.13 mtr including providing & fitting of (1) backalite sheet 3.5mm thick in sides, (2) 20 guage MS sheet outer side for

side walls, (3) backalite sheet 3.5 mm thick sheet for roof side, (4) 24 guage GI sheet out side with 15 mm plywood sandwitch fitting &

31 flooring with 19 mm water proof plywood sheet and (5) shock proof rubber mating. Job includes oil painting two coats, door locking

handle arrangement, providing proper air ventilation and fuse box. The meter & fuse box should be fitted on timber hold fast for holding

screw or nut bolts by semi skilled labour as per detailed technical specifications, drawings and instructions of the Engineer-in-charge.

Add 2% For Contengency Charges.

Add 1% For Labor Cess.

Total Project Cost Rs.

SBD SECTION-7 BILL OF QUANTITIES-305

CHAKLASI MUNICIPALITY, CHAKLASI

S.I.T.C OF 10 HP SUBMERSIBLE PUMPING MACHINERY WITH ALL COMPONENTS & ACCESSORIES AT DEVKAPURA AT WARD 03 AT CHAKLASI.

Description of Items Qty. Unit Amount (Rs.)

Lifting of submersible motor pump set complete with required No .& size of casing pipes by means of proper chain pulley block and

pipe. wrenches. Job includes stacking of pipes chronologically after due checking of threads. Up to 60 mtrs. 1.00 Nos. 1711.95

S.I.T.C. submersible pump set for bore of 150 mm. dia. or, more having 3 phase motor capacity not more than 10 H.P. and discharge

2 capacity having, Lifting and Lowering taken extra. 10 stage 575 to 480 LPM discharge at 60 to 70 mtr head for 65 mm dia delivery pipe.

Cat.III. 1.00 sets 39659.67

Lowering of submersible motor pump set at the depth of following, complete with required. Nos. and size of casing pipes erected by

3 means of proper chain pulley block & pipe wrenches after checking of threads of each pipe with coupling to take the load of the pump

set and pipe assembly filled up with water. Up to 60 mtrs. 1.00 Nos. 1711.95

Supplying & erecting approved make motor control cubical panel [Star delta] made from 16G CRCA sheet duly epoxy powder painted

inside and outside with hinged doors and locking with suitable size of ON - OFF isolator (AC 3 / 23 duty) main fuses. Digital volt and

current meter (in a single unit) with micro controller based control unit and current sensing single phasing preventer electronic overload

protection, over voltage (Programmable) protection and under voltage (Programmable) protection, prod less dry run protection

programming facility for setting of all parameter like overload current, high voltage limit, low voltage limit, dry run limit with digital

indication on seven segment LED display for any fault like over load, high voltage, low voltage, dry running single crimped, electronic

star delta timer, feather touch start / stop push buttons to be erected on angle iron frame. Grouted on wall the contactors will be of L& T,

Siemens, BCH make only). S/D up to 10 HP. 1.00 No 13794.58

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible Submersible copper cable approved make of following

1 R x 3 Core x 2.5 Sq. mm. 80.00 Mtr. 104.03

1 R x 3 Core x 4 Sq. mm. 50.00 Mtr. 146.45

Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe Technology

as per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising,

Inner pipe dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded by

highly conductive compound with high charge dissipation suitable for following type of applications with chamber and heavy duty cover.

(A)(approved make OEM has to submit test certificate including value of earth resistance of installation duly stamped and signed by

agency and officer Incharge has to ensure the value of earthing resistane mentioned in test Certificate) & having back filling compound

6 of (B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no load

& dry form, Sulphar content:- <2%(C) Back fill Compound :- Earthing compound should be capable to retain moisture for long time

Necessary test report must be submitted by Agency. For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT panel board,

Motors etc. using proper clamp. 20.00 Kg. 97.00

SBD SECTION-7 BILL OF QUANTITIES-306

Description of Items Qty. Unit Amount (Rs.)

Providing & erecting motor protection circuit breaker with shock proof enclosure (IP 65) erected as per direction for following motor HP

3 phase 440V A.C. up to 7.5 HP / 10 HP 12 to 18 Amp. 1.00 No 4803.56

Providing Water proof straight Joint in PVC insulated flat flexible copper cable by using insulating material, water proofing material &

making the joint complete. Up to 10 Sq. mm. 4.00 No 189.88

10 Supplying of following size of HEAVY UPVC column pipe with coupler and wire lock. For 80mm. 30.50 Rmt. 698.92

Providing and supplying in standard length ISI mark rigid unplasticised PVC pipes suitable for potable water with ring fit joint including

cost of rings, as per IS specification no. 4985/1988 including all local and central taxes, transportation, freight charges, octroi, inspection

11 charges, loading, unloading, conveyance to the departmental stores and including cost of jointing meterial etc. complete. Note : One

coupler / ring shall be provided with each full length pipe cost of which is included in rates below. Test Pressure 10 Kg/cm2. 110mm

PVC Pipes. 50.00 Rmt. 320.00

Lowering, laying, fixing and jointing PVC/uPVC/cPVC pipes and specials of following class and diameter including cost of conveyance

12 from stores to site of works including cost of labour, material, cement solvent, giving satisfactory hydraulic testing as per ISI code.

80/75mm Dia PVC Pipes 30.50 Rmt. 17.25

100/110mm Dia PVC Pipe 50.00 Rmt. 21.85

Supplying ISI Marked (Embossed) following size of Heavy duty “C” Class G.I. Pipe & erecting as directed by Engineer-in-charge with

necessary plumbing as desired. 100mm. 10.00 Rmt. 804.97

Supply of following size of TOP & BOTTOM accessories i.e. Adaptor set (CI) long, pump guard set, starter pipe Rubber ring for

submersible pump & UPVC column pipe as directed by Engineer - in - charge with necessary plumbing as desired. 80mm. 1.00 No 2681.55

15 Supplying & erecting G.l. bend for pipe connections suitable for 100mm. 1.00 No 548.43

Clamps made from MS plate with 3 holes on either side with nuts & bolts of standard make and suitable size. 450 mm X 65 mm X

mm flat suitable to 65/80 mm dia. pipe. 1.00 No 574.79

Manufacture, Supply & Delivery of Ductile Iron Flange socket spigot bends, tees, reducers or any other specials as per BS-EN-545/1995

Class-A series K12 suitable for use with D.I. Pipes manufactured as per IS:8329/1994 delivery of specials is to be made to GWSSB

17 store or site of works any where in Gujarat including all taxes, loading, unloading, carting, stacking, insurance, inspection charges, octroi

etc. complete. With external bitumen & zinc coating & internal cement mortar lining. Socket & Spigot type. From 80 to 300mm Dia.

Flange Ended. 30.00 Kgs. 151.00

Supplying & erecting Mild Steel heavy duty Flanges with rubber packing and hardware materials for pipe connections suitable for

Providing and supplying at store or site of work incl. freight, loading, unloading, stacking, insaurance & all taxes etc. complete. P. V. C.

Tee (Moulded). 110 x 75 mm. 1.00 No 338.00

P. V. C. Reducer. 110 x 75 mm. 1.00 No 182.00

P. V. C. Bend 90° Moulded heavy. 110mm 1.00 No 519.00

Providing and Supplying ISI mark CI D/F Sluice valves, butterfly valves & Reflux valves of following class and diameter including all

taxes, insurance, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to departmental stores,

stacking etc. complete. Sluice valves as per IS - 780 & 2906 / 1984. Sluice Valve ISI Mark only. PN-1.6 With hand/wheel cap operated

(Alt-1 type long body). 100mm. 1.00 Nos. 3902.00

SBD SECTION-7 BILL OF QUANTITIES-307

Description of Items Qty. Unit Amount (Rs.)

Excavation for pipe line trenches for water supply, sewerage line, manhole etc. all with shoring and struting if required as per required

21 gradient and line including safety provisions using site rails and stacking excavated stuff including up to all required lead cleaning the

site etc. complete for all lifts and strata as specified. In all sort of soil and soft murrum. Upto 1.50 Mt. Depth. 48.00 Cmt. 102.35

Lowering, laying and jointing in position following C. I. / D/F Reflux valves, Butterfly valves, Sluice valves and Air valves including cost of

22 all labour, jointing material, including nut bolts and giving satisfactory hydraulic testing, etc. complete. For 100mm Dia.

Construction of valves chambers in brick or bela stone masonry, locally available in C. M. 1:6. Foundation concrete 150 mm thick in C.

C. 1:4:8 of trap metal size 25 mm to 40 mm thick, inside cement plaster in C. M. 1:3 and cement pointing outside in C. M. 1:3 and top

cover of precast RCC slab 100 mm thick (with key hole in two parts, each with handles or MS Bar etc. complete as given size) Upto

23 Mt. depth from G. L. to pipe invert level incl. complete civil works but excl. cost of excavation and refilling, with cast in situ RCC slab in

one single piece with fixing of CI-MH Frame and cover (excl. cost of CI-MH Frame and cover) with 23 mm thick brick masonry wall in

C.M.1:6. Size of chamber 0.90 m x 0.90 m and 1.0 mt. deep. With precast slab in two parts 15 mm.

24 CI Frame & Cover For Valve Chamber 100.00 Kg. 58.00

Providing and casting in situ C.C. in grade M-20 (proportions as per mix design or as per table9 of IS456 2000 in masses by weigh

batching) using granite, quartzite trap metal of size 6 mm to 20 mm for RCC work, including scaffolding centering, formwork, needle

25 vibrated consolidation, curing complete up to 6 meter depth or height (excluding cost of reinforcement and neat finishing) with centering

and shuttering/deshuttering etc. complete for structure other than water retaining (Below G.L). For Thrust Block. With Form Work.

Refilling the pipeline trenches incl. ramming, watering, consolidating desposal of surplus stuff as directed within a radius of 3 km.

Supplying cutting, bending, binding and placing in position steel as per plan and design and as per ISS 2502 including cost of steel and

27 binding wire for reserviors/structures only including lift up to 6 meter height or depth below G.L. for all diameters. Do-Thermo

mechanically Treated (TMT) bars Fe-500 grade for all diameters. 20.00 Kgs 89.12

28 Compressor test of tube well by air compressor of 600 CFM / 150 PSI capacity in all districts. 2.00 Hour 3893.00

Labour charges for repairing leakage/ Jointing in CI/DI pipeline or Sluice Valve of following diameter at different places including

necessary excavation manually or by machinery, removing of mud, dewatering, cleaning of pipe, cutting of pipe, Jointing & repairing

using CID joints including CID joints, rubber rings, nut bolts, hiring excavator, Hydra/ Crane, dewatering machine, fuel, operator etc

complete (including cost of jointing material but excluding cost of pipe). 100mm. 2.00 No. 2068.85

Labour charges for repairing of leakage/ Jointing in PVC pipeline of following dia meter at different places including necessary

excavation manually or by mechanise excavation, dewatering removing of mud, cleaning of pipe and leakage portion, cutting the

pipeline & removing piece of pipe from trench with inclusive of mechanical devices JCB, Hydra/Crain if necessary & labours required

with providing material such couplers, solution etc. comp. (incl. all material but Exclu. cost of pipe). 110mm. 2.00 No. 1124.70

SBD SECTION-7 BILL OF QUANTITIES-308

Description of Items Qty. Unit Amount (Rs.)

Supply and installation of MS fabricated structure cabin @ site of work using 65 mm, 50 mm & 25 mm square pipes with cabin size

mtr x 1.5 mtr x 2.13 mtr including providing & fitting of (1) backalite sheet 3.5mm thick in sides, (2) 20 guage MS sheet outer side for

side walls, (3) backalite sheet 3.5 mm thick sheet for roof side, (4) 24 guage GI sheet out side with 15 mm plywood sandwitch fitting &

31 flooring with 19 mm water proof plywood sheet and (5) shock proof rubber mating. Job includes oil painting two coats, door locking

handle arrangement, providing proper air ventilation and fuse box. The meter & fuse box should be fitted on timber hold fast for holding

screw or nut bolts by semi skilled labour as per detailed technical specifications, drawings and instructions of the Engineer-in-charge.

Add 2% For Contengency Charges.

Add 1% For Labor Cess.

Total Project Cost Rs.

SBD SECTION-7 BILL OF QUANTITIES-309

CHAKLASI MUNICIPALITY, CHAKLASI

S.I.T.C OF 15 HP SUBMERSIBLE PUMPING MACHINERY WITH ALL COMPONENTS & ACCESSORIES AT JASPURA AT WARD 03 AT CHAKLASI.

Description of Items Qty. Unit Amount (Rs.)

Lifting of submersible motor pump set complete with required No .& size of casing pipes by means of proper chain pulley block and

pipe. wrenches. Job includes stacking of pipes chronologically after due checking of threads. Up to 60 mtrs. 1.00 Nos. 1711.95

S.I.T.C. submersible pump set for bore of 150 mm. dia. or, more having 3 phase motor capacity not more than 15 H.P. and discharge

2 capacity having, Lifting and Lowering taken extra. (8 stage) 695 to 492 L.P.M. at the head 48 to 73 mtrs suitable for 65/50 mm dia.

delivery pipe. Cat.III. 1.00 sets 49939.45

Lowering of submersible motor pump set at the depth of following, complete with required. Nos. and size of casing pipes erected by

3 means of proper chain pulley block & pipe wrenches after checking of threads of each pipe with coupling to take the load of the pump

set and pipe assembly filled up with water. Up to 60 mtrs. 1.00 Nos. 1711.95

Supplying & erecting approved make motor control cubical panel [Star delta] made from 16G CRCA sheet duly epoxy powder painted

inside and outside with hinged doors and locking with suitable size of ON - OFF isolator (AC 3 / 23 duty) main fuses. Digital volt and

current meter (in a single unit) with micro controller based control unit and current sensing single phasing preventer electronic overload

protection, over voltage (Programmable) protection and under voltage (Programmable) protection, prod less dry run protection

programming facility for setting of all parameter like overload current, high voltage limit, low voltage limit, dry run limit with digital

indication on seven segment LED display for any fault like over load, high voltage, low voltage, dry running single crimped, electronic

star delta timer, feather touch start / stop push buttons to be erected on angle iron frame. Grouted on wall the contactors will be of L& T,

Siemens, BCH make only). S/D up to 15 HP. 1.00 No 16053.95

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible Submersible copper cable approved make of following

1 R x 3 Core x 4 Sq. mm. 80.00 Mtr. 146.45

1 R x 3 Core x 6 Sq. mm. 30.00 Mtr. 172.71

Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe Technology

as per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising,

Inner pipe dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded by

highly conductive compound with high charge dissipation suitable for following type of applications with chamber and heavy duty cover.

(A)(approved make OEM has to submit test certificate including value of earth resistance of installation duly stamped and signed by

agency and officer Incharge has to ensure the value of earthing resistane mentioned in test Certificate) & having back filling compound

6 of (B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no load

& dry form, Sulphar content:- <2%(C) Back fill Compound :- Earthing compound should be capable to retain moisture for long time

Necessary test report must be submitted by Agency. For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT panel board,

Motors etc. using proper clamp. 20.00 Kg. 97.00

SBD SECTION-7 BILL OF QUANTITIES-310

Description of Items Qty. Unit Amount (Rs.)

Providing & erecting motor protection circuit breaker with shock proof enclosure (IP 65) erected as per direction for following motor HP

3 phase 440V A.C. up to 15 HP 18 to 26 Amp. 1.00 No 5230.79

Providing Water proof straight Joint in PVC insulated flat flexible copper cable by using insulating material, water proofing material &

making the joint complete. Up to 10 Sq. mm. 4.00 No 189.88

10 Supplying of following size of HEAVY UPVC column pipe with coupler and wire lock. For 100mm. 30.50 Rmt. 1130.19

Providing and supplying in standard length ISI mark rigid unplasticised PVC pipes suitable for potable water with ring fit joint including

cost of rings, as per IS specification no. 4985/1988 including all local and central taxes, transportation, freight charges, octroi,

11 inspection charges, loading, unloading, conveyance to the departmental stores and including cost of jointing meterial etc. complete.

Note : One coupler / ring shall be provided with each full length pipe cost of which is included in rates below. Test Pressure 10 Kg/cm2

110mm PVC Pipes. 30.00 Rmt. 320.00

Lowering, laying, fixing and jointing PVC/uPVC/cPVC pipes and specials of following class and diameter including cost of conveyance

12 from stores to site of works including cost of labour, material, cement solvent, giving satisfactory hydraulic testing as per ISI code.

100/110mm Dia PVC Pipes 60.50 Rmt. 21.85

Supplying ISI Marked (Embossed) following size of Heavy duty “C” Class G.I. Pipe & erecting as directed by Engineer-in-charge with

necessary plumbing as desired. 100mm. 10.00 Rmt. 804.97

Supply of following size of TOP & BOTTOM accessories i.e. Adaptor set (CI) long, pump guard set, starter pipe Rubber ring for

submersible pump & UPVC column pipe as directed by Engineer - in - charge with necessary plumbing as desired. 100mm. 1.00 No 3872.34

15 Supplying & erecting G.l. bend for pipe connections suitable for 100mm. 1.00 No 548.43

Clamps made from MS plate with 3 holes on either side with nuts & bolts of standard make and suitable size. 450 mm X 65 mm X

mm flat suitable to 100/125 mm dia. pipe. 1.00 No 693.94

Manufacture, Supply & Delivery of Ductile Iron Flange socket spigot bends, tees, reducers or any other specials as per BS-EN-

545/1995 Class-A series K12 suitable for use with D.I. Pipes manufactured as per IS:8329/1994 delivery of specials is to be made to

17 GWSSB store or site of works any where in Gujarat including all taxes, loading, unloading, carting, stacking, insurance, inspection

charges, octroi etc. complete. With external bitumen & zinc coating & internal cement mortar lining. Socket & Spigot type. From 80 to

300mm Dia. Flange Ended. 30.00 Kgs. 151.00

Supplying & erecting Mild Steel heavy duty Flanges with rubber packing and hardware materials for pipe connections suitable for

Providing and supplying at store or site of work incl. freight, loading, unloading, stacking, insaurance & all taxes etc. complete. P. V. C.

Tee (Moulded). 110 x 75 mm. 1.00 No 338.00

P. V. C. Reducer. 110 x 75 mm. 1.00 No 182.00

P. V. C. Bend 90° Moulded heavy. 110mm 1.00 No 519.00

Providing and Supplying ISI mark CI D/F Sluice valves, butterfly valves & Reflux valves of following class and diameter including all

taxes, insurance, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to departmental stores,

stacking etc. complete. Sluice valves as per IS - 780 & 2906 / 1984. Sluice Valve ISI Mark only. PN-1.6 With hand/wheel cap operated

(Alt-1 type long body). 100mm. 1.00 Nos. 3902.00

SBD SECTION-7 BILL OF QUANTITIES-311

Description of Items Qty. Unit Amount (Rs.)

Excavation for pipe line trenches for water supply, sewerage line, manhole etc. all with shoring and struting if required as per required

21 gradient and line including safety provisions using site rails and stacking excavated stuff including up to all required lead cleaning the

site etc. complete for all lifts and strata as specified. In all sort of soil and soft murrum. Upto 1.50 Mt. Depth. 5.00 Cmt. 102.35

Lowering, laying and jointing in position following C. I. / D/F Reflux valves, Butterfly valves, Sluice valves and Air valves including cost of

all labour, jointing material, including nut bolts and giving satisfactory hydraulic testing, etc. complete. For 100mm Dia. 1.00 Nos 504.85

Construction of valves chambers in brick or bela stone masonry, locally available in C. M. 1:6. Foundation concrete 150 mm thick in C.

C. 1:4:8 of trap metal size 25 mm to 40 mm thick, inside cement plaster in C. M. 1:3 and cement pointing outside in C. M. 1:3 and top

cover of precast RCC slab 100 mm thick (with key hole in two parts, each with handles or MS Bar etc. complete as given size) Upto

23 Mt. depth from G. L. to pipe invert level incl. complete civil works but excl. cost of excavation and refilling, with cast in situ RCC slab in

one single piece with fixing of CI-MH Frame and cover (excl. cost of CI-MH Frame and cover) with 23 mm thick brick masonry wall in

C.M.1:6. Size of chamber 0.90 m x 0.90 m and 1.0 mt. deep. With precast slab in two parts 15 mm.

24 CI Frame & Cover For Valve Chamber 100.00 Kg. 58.00

Providing and casting in situ C.C. in grade M-20 (proportions as per mix design or as per table9 of IS456 2000 in masses by weigh

batching) using granite, quartzite trap metal of size 6 mm to 20 mm for RCC work, including scaffolding centering, formwork, needle

25 vibrated consolidation, curing complete up to 6 meter depth or height (excluding cost of reinforcement and neat finishing) with centering

and shuttering/deshuttering etc. complete for structure other than water retaining (Below G.L). For Thrust Block. With Form Work.

Refilling the pipeline trenches incl. ramming, watering, consolidating desposal of surplus stuff as directed within a radius of 3 km.

Supplying cutting, bending, binding and placing in position steel as per plan and design and as per ISS 2502 including cost of steel and

27 binding wire for reserviors/structures only including lift up to 6 meter height or depth below G.L. for all diameters. Do-Thermo

mechanically Treated (TMT) bars Fe-500 grade for all diameters. 20.00 Kgs 89.12

28 Compressor test of tube well by air compressor of 600 CFM / 150 PSI capacity in all districts. 2.00 Hour 3893.00

Labour charges for repairing leakage/ Jointing in CI/DI pipeline or Sluice Valve of following diameter at different places including

necessary excavation manually or by machinery, removing of mud, dewatering, cleaning of pipe, cutting of pipe, Jointing & repairing

using CID joints including CID joints, rubber rings, nut bolts, hiring excavator, Hydra/ Crane, dewatering machine, fuel, operator etc

complete (including cost of jointing material but excluding cost of pipe). 80mm. 2.00 No. 1828.50

Labour charges for repairing of leakage/ Jointing in PVC pipeline of following dia meter at different places including necessary

excavation manually or by mechanise excavation, dewatering removing of mud, cleaning of pipe and leakage portion, cutting the

pipeline & removing piece of pipe from trench with inclusive of mechanical devices JCB, Hydra/Crain if necessary & labours required

with providing material such couplers, solution etc. comp. (incl. all material but Exclu. cost of pipe). 110mm. 2.00 No. 1124.70

Providing and fixing 50 cm wide M.S. Ladder fabricated from M.S. Flats 10 mm x 75mm with 20 mm dia steel bar steps in double rows,

31 @ 30 cm C/C. The include stays of 10 mm x 50 mm flats fixed at 3 meter C/C with welding anchoring and 3 coats anticorrosive paint.

SBD SECTION-7 BILL OF QUANTITIES-312

Description of Items Qty. Unit Amount (Rs.)

Supply and installation of MS fabricated structure cabin @ site of work using 65 mm, 50 mm & 25 mm square pipes with cabin size

mtr x 1.5 mtr x 2.13 mtr including providing & fitting of (1) backalite sheet 3.5mm thick in sides, (2) 20 guage MS sheet outer side for

side walls, (3) backalite sheet 3.5 mm thick sheet for roof side, (4) 24 guage GI sheet out side with 15 mm plywood sandwitch fitting &

32 flooring with 19 mm water proof plywood sheet and (5) shock proof rubber mating. Job includes oil painting two coats, door locking

handle arrangement, providing proper air ventilation and fuse box. The meter & fuse box should be fitted on timber hold fast for holding

screw or nut bolts by semi skilled labour as per detailed technical specifications, drawings and instructions of the Engineer-in-charge.

Add 2% For Contengency Charges.

Add 1% For Labor Cess.

Total Project Cost Rs.

SBD SECTION-7 BILL OF QUANTITIES-313

CHAKLASI MUNICIPALITY, CHAKLASI

S.I.T.C OF 10 HP SUBMERSIBLE PUMPING MACHINERY WITH ALL COMPONENTS & ACCESSORIES AT GULBHAI TEKRA AT WARD 05 AT CHAKLASI.

Description of Items Qty. Unit Amount (Rs.)

Lifting of submersible motor pump set complete with required No .& size of casing pipes by means of proper chain pulley block and

pipe. wrenches. Job includes stacking of pipes chronologically after due checking of threads. Up to 60 mtrs. 1.00 Nos. 1711.95

S.I.T.C. submersible pump set suitable for bore of 150 mm. dia. or more having three phase motor capacity not more than 7.5 H.P. with

2 following capacity. Lifting and Lowering taken extra. (8 stage) 390 to 350 LPM discharge at 62 to 70 mtrs. head respectively suitable for

50mm dia. delivery pipe. Cat.III. 1.00 sets 33557.25

Lowering of submersible motor pump set at the depth of following, complete with required. Nos. and size of casing pipes erected by means

3 of proper chain pulley block & pipe wrenches after checking of threads of each pipe with coupling to take the load of the pump set and pipe

assembly filled up with water. Up to 60 mtrs. 1.00 Nos. 1711.95

Supplying & erecting approved make motor control cubical panel [Star delta] made from 16G CRCA sheet duly epoxy powder painted

inside and outside with hinged doors and locking with suitable size of ON - OFF isolator (AC 3 / 23 duty) main fuses. Digital volt and current

meter (in a single unit) with micro controller based control unit and current sensing single phasing preventer electronic overload protection,

over voltage (Programmable) protection and under voltage (Programmable) protection, prod less dry run protection programming facility for

setting of all parameter like overload current, high voltage limit, low voltage limit, dry run limit with digital indication on seven segment LED

display for any fault like over load, high voltage, low voltage, dry running single crimped, electronic star delta timer, feather touch start / stop

push buttons to be erected on angle iron frame. Grouted on wall the contactors will be of L& T, Siemens, BCH make only). S/D up to

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible Submersible copper cable approved make of following Size.

1 R x 3 Core x 2.5 Sq. mm. 80.00 Mtr. 104.03

1 R x 3 Core x 4 Sq. mm. 50.00 Mtr. 146.45

Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe Technology as

per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising, Inner

pipe dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded by highly

conductive compound with high charge dissipation suitable for following type of applications with chamber and heavy duty cover.

(A)(approved make OEM has to submit test certificate including value of earth resistance of installation duly stamped and signed by agency

and officer Incharge has to ensure the value of earthing resistane mentioned in test Certificate) & having back filling compound of (B) Inner

6 chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no load & dry form,

Sulphar content:- <2%(C) Back fill Compound :- Earthing compound should be capable to retain moisture for long time Necessary test

report must be submitted by Agency. For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT panel board, Motors

etc. using proper clamp. 20.00 Kg. 97.00

SBD SECTION-7 BILL OF QUANTITIES-314

Description of Items Qty. Unit Amount (Rs.)

Providing & erecting motor protection circuit breaker with shock proof enclosure (IP 65) erected as per direction for following motor HP

phase 440V A.C. up to 7.5 HP / 10 HP 12 to 18 Amp. 1.00 No 4803.56

Providing Water proof straight Joint in PVC insulated flat flexible copper cable by using insulating material, water proofing material & making

the joint complete. Up to 10 Sq. mm. 4.00 No 189.88

10 Supplying of following size of HEAVY UPVC column pipe with coupler and wire lock. For 80mm. 30.50 Rmt. 698.92

Providing and supplying in standard length ISI mark rigid unplasticised PVC pipes suitable for potable water with ring fit joint including cost

of rings, as per IS specification no. 4985/1988 including all local and central taxes, transportation, freight charges, octroi, inspection

11 charges, loading, unloading, conveyance to the departmental stores and including cost of jointing meterial etc. complete. Note : One coupler

/ ring shall be provided with each full length pipe cost of which is included in rates below. Test Pressure 10 Kg/cm2. 110mm PVC Pipes.

Lowering, laying, fixing and jointing PVC/uPVC/cPVC pipes and specials of following class and diameter including cost of conveyance from

12 stores to site of works including cost of labour, material, cement solvent, giving satisfactory hydraulic testing as per ISI code. 80/75mm Dia

PVC Pipes 30.50 Rmt. 17.25

100/110mm Dia PVC Pipe 50.00 Rmt. 21.85

Supplying ISI Marked (Embossed) following size of Heavy duty “C” Class G.I. Pipe & erecting as directed by Engineer-in-charge with

necessary plumbing as desired. 100mm. 10.00 Rmt. 804.97

Supply of following size of TOP & BOTTOM accessories i.e. Adaptor set (CI) long, pump guard set, starter pipe Rubber ring for submersible

pump & UPVC column pipe as directed by Engineer - in - charge with necessary plumbing as desired. 80mm. 1.00 No 2681.55

15 Supplying & erecting G.l. bend for pipe connections suitable for 100mm. 1.00 No 548.43

Clamps made from MS plate with 3 holes on either side with nuts & bolts of standard make and suitable size. 450 mm X 65 mm X 10 mm

flat suitable to 65/80 mm dia. pipe. 1.00 No 574.79

Manufacture, Supply & Delivery of Ductile Iron Flange socket spigot bends, tees, reducers or any other specials as per BS-EN-545/1995

Class-A series K12 suitable for use with D.I. Pipes manufactured as per IS:8329/1994 delivery of specials is to be made to GWSSB store or

17 site of works any where in Gujarat including all taxes, loading, unloading, carting, stacking, insurance, inspection charges, octroi etc.

complete. With external bitumen & zinc coating & internal cement mortar lining. Socket & Spigot type. From 80 to 300mm Dia. Flange

Ended. 30.00 Kgs. 151.00

Supplying & erecting Mild Steel heavy duty Flanges with rubber packing and hardware materials for pipe connections suitable for 100mm.

Providing and supplying at store or site of work incl. freight, loading, unloading, stacking, insaurance & all taxes etc. complete. P. V. C. Tee

(Moulded). 110 x 75 mm. 1.00 No 338.00

P. V. C. Reducer. 110 x 75 mm. 1.00 No 182.00

P. V. C. Bend 90° Moulded heavy. 110mm 1.00 No 519.00

SBD SECTION-7 BILL OF QUANTITIES-315

Description of Items Qty. Unit Amount (Rs.)

Providing and Supplying ISI mark CI D/F Sluice valves, butterfly valves & Reflux valves of following class and diameter including all taxes,

insurance, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to departmental stores, stacking etc.

complete. Sluice valves as per IS - 780 & 2906 / 1984. Sluice Valve ISI Mark only. PN-1.6 With hand/wheel cap operated (Alt-1 type long

Excavation for pipe line trenches for water supply, sewerage line, manhole etc. all with shoring and struting if required as per required

21 gradient and line including safety provisions using site rails and stacking excavated stuff including up to all required lead cleaning the site

etc. complete for all lifts and strata as specified. In all sort of soil and soft murrum. Upto 1.50 Mt. Depth. 48.00 Cmt. 102.35

Lowering, laying and jointing in position following C. I. / D/F Reflux valves, Butterfly valves, Sluice valves and Air valves including cost of all

labour, jointing material, including nut bolts and giving satisfactory hydraulic testing, etc. complete. For 100mm Dia. 1.00 Nos 504.85

Construction of valves chambers in brick or bela stone masonry, locally available in C. M. 1:6. Foundation concrete 150 mm thick in C. C.

1:4:8 of trap metal size 25 mm to 40 mm thick, inside cement plaster in C. M. 1:3 and cement pointing outside in C. M. 1:3 and top cover of

precast RCC slab 100 mm thick (with key hole in two parts, each with handles or MS Bar etc. complete as given size) Upto 1 Mt. depth from

G. L. to pipe invert level incl. complete civil works but excl. cost of excavation and refilling, with cast in situ RCC slab in one single piece with

fixing of CI-MH Frame and cover (excl. cost of CI-MH Frame and cover) with 23 mm thick brick masonry wall in C.M.1:6. Size of chamber

0.90 m x 0.90 m and 1.0 mt. deep. With precast slab in two parts 15 mm. 1.00 Nos 8898.70

24 CI Frame & Cover For Valve Chamber 100.00 Kg. 58.00

Providing and casting in situ C.C. in grade M-20 (proportions as per mix design or as per table9 of IS456 2000 in masses by weigh

batching) using granite, quartzite trap metal of size 6 mm to 20 mm for RCC work, including scaffolding centering, formwork, needle

25 vibrated consolidation, curing complete up to 6 meter depth or height (excluding cost of reinforcement and neat finishing) with centering and

shuttering/deshuttering etc. complete for structure other than water retaining (Below G.L). For Thrust Block. With Form Work.

26 Refilling the pipeline trenches incl. ramming, watering, consolidating desposal of surplus stuff as directed within a radius of 3 km. 48.00 Cmt. 25.30

Supplying cutting, bending, binding and placing in position steel as per plan and design and as per ISS 2502 including cost of steel and

27 binding wire for reserviors/structures only including lift up to 6 meter height or depth below G.L. for all diameters. Do-Thermo mechanically

Treated (TMT) bars Fe-500 grade for all diameters. 20.00 Kgs 89.12

28 Compressor test of tube well by air compressor of 600 CFM / 150 PSI capacity in all districts. 2.00 Hour 3893.00

Labour charges for repairing leakage/ Jointing in CI/DI pipeline or Sluice Valve of following diameter at different places including necessary

excavation manually or by machinery, removing of mud, dewatering, cleaning of pipe, cutting of pipe, Jointing & repairing using CID joints

including CID joints, rubber rings, nut bolts, hiring excavator, Hydra/ Crane, dewatering machine, fuel, operator etc complete (including cost

of jointing material but excluding cost of pipe). 100mm. 2.00 No. 2068.85

Labour charges for repairing of leakage/ Jointing in PVC pipeline of following dia meter at different places including necessary excavation

manually or by mechanise excavation, dewatering removing of mud, cleaning of pipe and leakage portion, cutting the pipeline & removing

piece of pipe from trench with inclusive of mechanical devices JCB, Hydra/Crain if necessary & labours required with providing material

such couplers, solution etc. comp. (incl. all material but Exclu. cost of pipe). 110mm. 2.00 No. 1124.70

SBD SECTION-7 BILL OF QUANTITIES-316

Description of Items Qty. Unit Amount (Rs.)

Supply and installation of MS fabricated structure cabin @ site of work using 65 mm, 50 mm & 25 mm square pipes with cabin size 1.5 mtr

x 1.5 mtr x 2.13 mtr including providing & fitting of (1) backalite sheet 3.5mm thick in sides, (2) 20 guage MS sheet outer side for side walls,

(3) backalite sheet 3.5 mm thick sheet for roof side, (4) 24 guage GI sheet out side with 15 mm plywood sandwitch fitting & flooring with

31 mm water proof plywood sheet and (5) shock proof rubber mating. Job includes oil painting two coats, door locking handle arrangement,

providing proper air ventilation and fuse box. The meter & fuse box should be fitted on timber hold fast for holding screw or nut bolts by semi

skilled labour as per detailed technical specifications, drawings and instructions of the Engineer-in-charge.

Add 2% For Contengency Charges.

Add 1% For Labor Cess.

Total Project Cost Rs.

SBD SECTION-7 BILL OF QUANTITIES-317

CHAKLASI MUNICIPALITY, CHAKLASI

S.I.T.C OF 15 HP SUBMERSIBLE PUMPING MACHINERY WITH ALL COMPONENTS & ACCESSORIES AT VANIPURA KHADHAN VISTAR AT WARD 05 AT CHAKLASI.

Description of Items Qty. Unit Material + Amount (Rs.)

Lifting of submersible motor pump set complete with required No .& size of casing pipes by means of proper chain pulley block and pipe.

wrenches. Job includes stacking of pipes chronologically after due checking of threads. Up to 60 mtrs. 1.00 Nos. 1711.95

S.I.T.C. submersible pump set for bore of 150 mm. dia. or, more having 3 phase motor capacity not more than 15 H.P. and discharge

2 capacity having, Lifting and Lowering taken extra. (8 stage) 695 to 492 L.P.M. at the head 48 to 73 mtrs suitable for 65/50 mm dia. delivery

pipe. Cat.III. 1.00 sets 49939.45

Lowering of submersible motor pump set at the depth of following, complete with required. Nos. and size of casing pipes erected by means

3 of proper chain pulley block & pipe wrenches after checking of threads of each pipe with coupling to take the load of the pump set and pipe

assembly filled up with water. Up to 60 mtrs. 1.00 Nos. 1711.95

Supplying & erecting approved make motor control cubical panel [Star delta] made from 16G CRCA sheet duly epoxy powder painted inside

and outside with hinged doors and locking with suitable size of ON - OFF isolator (AC 3 / 23 duty) main fuses. Digital volt and current meter

(in a single unit) with micro controller based control unit and current sensing single phasing preventer electronic overload protection, over

voltage (Programmable) protection and under voltage (Programmable) protection, prod less dry run protection programming facility for

setting of all parameter like overload current, high voltage limit, low voltage limit, dry run limit with digital indication on seven segment LED

display for any fault like over load, high voltage, low voltage, dry running single crimped, electronic star delta timer, feather touch start / stop

push buttons to be erected on angle iron frame. Grouted on wall the contactors will be of L& T, Siemens, BCH make only). S/D up to 15 HP.

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible Submersible copper cable approved make of following Size.

1 R x 3 Core x 4 Sq. mm. 80.00 Mtr. 146.45

1 R x 3 Core x 6 Sq. mm. 30.00 Mtr. 172.71

Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe Technology as

per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising, Inner pipe

dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded by highly

conductive compound with high charge dissipation suitable for following type of applications with chamber and heavy duty cover.

(A)(approved make OEM has to submit test certificate including value of earth resistance of installation duly stamped and signed by agency

and officer Incharge has to ensure the value of earthing resistane mentioned in test Certificate) & having back filling compound of (B) Inner

6 chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no load & dry form,

Sulphar content:- <2%(C) Back fill Compound :- Earthing compound should be capable to retain moisture for long time Necessary test

report must be submitted by Agency. For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT panel board, Motors

etc. using proper clamp. 20.00 Kg. 97.00

SBD SECTION-7 BILL OF QUANTITIES-318

Description of Items Qty. Unit Material + Amount (Rs.)

Providing & erecting motor protection circuit breaker with shock proof enclosure (IP 65) erected as per direction for following motor HP

phase 440V A.C. up to 15 HP 18 to 26 Amp. 1.00 No 5230.79

Providing Water proof straight Joint in PVC insulated flat flexible copper cable by using insulating material, water proofing material & making

the joint complete. Up to 10 Sq. mm. 4.00 No 189.88

10 Supplying of following size of HEAVY UPVC column pipe with coupler and wire lock. For 100mm. 30.50 Rmt. 1130.19

Lowering, laying, fixing and jointing PVC/uPVC/cPVC pipes and specials of following class and diameter including cost of conveyance from

11 stores to site of works including cost of labour, material, cement solvent, giving satisfactory hydraulic testing as per ISI code. 100/110mm

Supplying ISI Marked (Embossed) following size of Heavy duty “C” Class G.I. Pipe & erecting as directed by Engineer-in-charge with

necessary plumbing as desired. 100mm. 10.00 Rmt. 804.97

Supply of following size of TOP & BOTTOM accessories i.e. Adaptor set (CI) long, pump guard set, starter pipe Rubber ring for submersible

pump & UPVC column pipe as directed by Engineer - in - charge with necessary plumbing as desired. 100mm. 1.00 No 3872.34

14 Supplying & erecting G.l. bend for pipe connections suitable for 100mm. 1.00 No 548.43

Clamps made from MS plate with 3 holes on either side with nuts & bolts of standard make and suitable size. 450 mm X 65 mm X 10 mm

flat suitable to 100/125 mm dia. pipe. 1.00 No 693.94

Supplying & erecting Mild Steel heavy duty Flanges with rubber packing and hardware materials for pipe connections suitable for 100mm.

Providing and supplying at store or site of work incl. freight, loading, unloading, stacking, insaurance & all taxes etc. complete. P. V. C. Tee

(Moulded). 110 x 75 mm. 1.00 No 338.00

P. V. C. Reducer. 110 x 75 mm. 1.00 No 182.00

P. V. C. Bend 90° Moulded heavy. 110mm 1.00 No 519.00

Providing and Supplying ISI mark CI D/F Sluice valves, butterfly valves & Reflux valves of following class and diameter including all taxes,

insurance, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to departmental stores, stacking etc.

complete. Sluice valves as per IS - 780 & 2906 / 1984. Sluice Valve ISI Mark only. PN-1.6 With hand/wheel cap operated (Alt-1 type long

body). 80mm. 1.00 Nos. 2946.00

Excavation for pipe line trenches for water supply, sewerage line, manhole etc. all with shoring and struting if required as per required

19 gradient and line including safety provisions using site rails and stacking excavated stuff including up to all required lead cleaning the site

etc. complete for all lifts and strata as specified. In all sort of soil and soft murrum. Upto 1.50 Mt. Depth. 10.00 Cmt. 102.35

SBD SECTION-7 BILL OF QUANTITIES-319

Description of Items Qty. Unit Material + Amount (Rs.)

Lowering, laying and jointing in position following C. I. / D/F Reflux valves, Butterfly valves, Sluice valves and Air valves including cost of all

labour, jointing material, including nut bolts and giving satisfactory hydraulic testing, etc. complete. For 100mm Dia. 1.00 Nos 460.00

Providing and casting in situ C.C. in grade M-20 (proportions as per mix design or as per table9 of IS456 2000 in masses by weigh batching)

using granite, quartzite trap metal of size 6 mm to 20 mm for RCC work, including scaffolding centering, formwork, needle vibrated

21 consolidation, curing complete up to 6 meter depth or height (excluding cost of reinforcement and neat finishing) with centering and

shuttering/deshuttering etc. complete for structure other than water retaining (Below G.L). For Thrust Block. With Form Work.

22 Refilling the pipeline trenches incl. ramming, watering, consolidating desposal of surplus stuff as directed within a radius of 3 km. 10.00 Cmt. 25.30

Supplying cutting, bending, binding and placing in position steel as per plan and design and as per ISS 2502 including cost of steel and

23 binding wire for reserviors/structures only including lift up to 6 meter height or depth below G.L. for all diameters. Do-Thermo mechanically

Treated (TMT) bars Fe-500 grade for all diameters. 20.00 Kgs 89.12

24 Compressor test of tube well by air compressor of 600 CFM / 150 PSI capacity in all districts. 2.00 Hour 3893.00

Labour charges for repairing leakage/ Jointing in CI/DI pipeline or Sluice Valve of following diameter at different places including necessary

excavation manually or by machinery, removing of mud, dewatering, cleaning of pipe, cutting of pipe, Jointing & repairing using CID joints

including CID joints, rubber rings, nut bolts, hiring excavator, Hydra/ Crane, dewatering machine, fuel, operator etc complete (including cost

of jointing material but excluding cost of pipe). 75mm. 2.00 No. 1828.50

Add 2% For Contengency Charges.

Add 1% For Labor Cess.

Total Project Cost Rs.

SBD SECTION-7 BILL OF QUANTITIES-320

CHAKLASI MUNICIPALITY, CHAKLASI

S.I.T.C OF 15 HP SUBMERSIBLE PUMPING MACHINERY WITH ALL COMPONENTS & ACCESSORIES AT DARAKALI VISTAR AT WARD 05 AT CHAKLASI.

Description of Items Qty. Unit Material + Amount (Rs.)

Lifting of submersible motor pump set complete with required No .& size of casing pipes by means of proper chain pulley block

and pipe. wrenches. Job includes stacking of pipes chronologically after due checking of threads. Up to 60 mtrs. 1.00 Nos. 1711.95

S.I.T.C. submersible pump set for bore of 150 mm. dia. Or more having 3 phase motor capacity about 20 H.P and discharge capacity

2 having. Lifting and Lowering taken extra. (8 Stage) 1000 to 900 LPM discharge at head 59 to 64 mtrs suitable for 80 mm dia. delivery

pipe. Cat.III. 1.00 sets 58187.11

Lowering of submersible motor pump set at the depth of following, complete with required. Nos. and size of casing pipes erected by

3 means of proper chain pulley block & pipe wrenches after checking of threads of each pipe with coupling to take the load of the pump

set and pipe assembly filled up with water. Up to 60 mtrs. 1.00 Nos. 1711.95

Supplying & erecting approved make motor control cubical panel [Star delta] made from 16G CRCA sheet duly epoxy powder

painted inside and outside with hinged doors and locking with suitable size of ON - OFF isolator (AC 3 / 23 duty) main fuses. Digital

volt and current meter (in a single unit) with micro controller based control unit and current sensing single phasing preventer

electronic overload protection, over voltage (Programmable) protection and under voltage (Programmable) protection, prod less dry

run protection programming facility for setting of all parameter like overload current, high voltage limit, low voltage limit, dry run limit

with digital indication on seven segment LED display for any fault like over load, high voltage, low voltage, dry running single crimped,

electronic star delta timer, feather touch start / stop push buttons to be erected on angle iron frame. Grouted on wall the contactors

will be of L& T, Siemens, BCH make only). S/D up to 20 HP. 1.00 No 14688.43

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible Submersible copper cable approved make of following

1 R x 3 Core x 6 Sq. mm. 80.00 Mtr. 172.71

1 R x 3 Core x 10 Sq. mm. 30.00 Mtr. 295.93

Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron

galvanising, Inner pipe dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value

surrounded by highly conductive compound with high charge dissipation suitable for following type of applications with chamber and

heavy duty cover. (A)(approved make OEM has to submit test certificate including value of earth resistance of installation duly

stamped and signed by agency and officer Incharge has to ensure the value of earthing resistane mentioned in test Certificate) &

6 having back filling compound of (B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017,

Voltage drop:- < 1 volt at no load & dry form, Sulphar content:- <2%(C) Back fill Compound :- Earthing compound should be capable

to retain moisture for long time Necessary test report must be submitted by Agency. For Electrical Installation up to 440V in normal

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg. 1.00 No 4591.46

Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T., OCB/ ACB/ Transformer LT panel board,

Motors etc. using proper clamp. 20.00 Kg. 97.00

SBD SECTION-7 BILL OF QUANTITIES-321

Description of Items Qty. Unit Material + Amount (Rs.)

Providing & erecting motor protection circuit breaker with shock proof enclosure (IP 65) erected as per direction for following motor

HP 3 phase 440V A.C. up to 20 HP 24 to 36 Amp. 1.00 No 7080.10

Providing Water proof straight Joint in PVC insulated flat flexible copper cable by using insulating material, water proofing material &

making the joint complete. Up to 10 Sq. mm. 4.00 No 189.88

10 Supplying of following size of HEAVY UPVC column pipe with coupler and wire lock. For 100mm. 30.50 Rmt. 1130.19

Providing and supplying in standard length ISI mark rigid unplasticised PVC pipes suitable for potable water with ring fit joint including

cost of rings, as per IS specification no. 4985/1988 including all local and central taxes, transportation, freight charges, octroi,

11 inspection charges, loading, unloading, conveyance to the departmental stores and including cost of jointing meterial etc. complete.

Note : One coupler / ring shall be provided with each full length pipe cost of which is included in rates below. Test Pressure

Kg/cm2. 110mm PVC Pipes. 30.00 Rmt. 320.00

Lowering, laying, fixing and jointing PVC/uPVC/cPVC pipes and specials of following class and diameter including cost of conveyance

12 from stores to site of works including cost of labour, material, cement solvent, giving satisfactory hydraulic testing as per ISI code.

100/110mm Dia PVC Pipes 60.50 Rmt. 21.85

Supplying ISI Marked (Embossed) following size of Heavy duty “C” Class G.I. Pipe & erecting as directed by Engineer-in-charge with

necessary plumbing as desired. 100mm. 10.00 Rmt. 804.97

Providing and fixing flanged D.I.D.F. / Class K-9 pipes vertically for RCC. Reservoir incl. providing clamps at every 3 mt incl. jointing

materials such as nuts, bolts, rubber packing, hydraulic testing and necessary scaffolding etc. complete. 100mm. 30.00 Rmt. 2684.10

Supply of following size of TOP & BOTTOM accessories i.e. Adaptor set (CI) long, pump guard set, starter pipe Rubber ring for

15 submersible pump & UPVC column pipe as directed by Engineer - in - charge with necessary plumbing as desired. 100mm.

16 Supplying & erecting G.l. bend for pipe connections suitable for 100mm. 1.00 No 548.43

Clamps made from MS plate with 3 holes on either side with nuts & bolts of standard make and suitable size. 450 mm X 65 mm X

mm flat suitable to 100/125 mm dia. pipe. 1.00 No 693.94

Manufacture, Supply & Delivery of Ductile Iron Flange socket spigot bends, tees, reducers or any other specials as per BS-EN-

545/1995 Class-A series K12 suitable for use with D.I. Pipes manufactured as per IS:8329/1994 delivery of specials is to be made to

18 GWSSB store or site of works any where in Gujarat including all taxes, loading, unloading, carting, stacking, insurance, inspection

charges, octroi etc. complete. With external bitumen & zinc coating & internal cement mortar lining. Socket & Spigot type. From 80 to

300mm Dia. Flange Ended. 60.00 Kgs. 151.00

Supplying & erecting Mild Steel heavy duty Flanges with rubber packing and hardware materials for pipe connections suitable for

SBD SECTION-7 BILL OF QUANTITIES-322

Description of Items Qty. Unit Material + Amount (Rs.)

Providing and supplying at store or site of work incl. freight, loading, unloading, stacking, insaurance & all taxes etc. complete. P. V.

C. Tee (Moulded). 110 x 75 mm. 1.00 No 338.00

P. V. C. Reducer. 110 x 75 mm. 1.00 No 182.00

P. V. C. Bend 90° Moulded heavy. 110mm 1.00 No 519.00

Providing and Supplying ISI mark CI D/F Sluice valves, butterfly valves & Reflux valves of following class and diameter including all

taxes, insurance, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to departmental stores,

stacking etc. complete. Sluice valves as per IS - 780 & 2906 / 1984. Sluice Valve ISI Mark only. PN-1.6 With hand/wheel cap

operated (Alt-1 type long body). 100mm. 1.00 Nos. 3902.00

Excavation for pipe line trenches for water supply, sewerage line, manhole etc. all with shoring and struting if required as per required

gradient and line including safety provisions using site rails and stacking excavated stuff including up to all required lead cleaning the

site etc. complete for all lifts and strata as specified. In all sort of soil and soft murrum. Upto 1.50 Mt. Depth.

Lowering, laying and jointing in position following C. I. / D/F Reflux valves, Butterfly valves, Sluice valves and Air valves including cost

23 of all labour, jointing material, including nut bolts and giving satisfactory hydraulic testing, etc. complete. For 100mm Dia.

Providing and casting in situ C.C. in grade M-20 (proportions as per mix design or as per table9 of IS456 2000 in masses by weigh

batching) using granite, quartzite trap metal of size 6 mm to 20 mm for RCC work, including scaffolding centering, formwork, needle

24 vibrated consolidation, curing complete up to 6 meter depth or height (excluding cost of reinforcement and neat finishing) with

centering and shuttering/deshuttering etc. complete for structure other than water retaining (Below G.L). For Thrust Block. With Form

Work. 0.50 Cmt. 6348.00

Refilling the pipeline trenches incl. ramming, watering, consolidating desposal of surplus stuff as directed within a radius of 3 km.

Supplying cutting, bending, binding and placing in position steel as per plan and design and as per ISS 2502 including cost of steel

26 and binding wire for reserviors/structures only including lift up to 6 meter height or depth below G.L. for all diameters. Do-Thermo

mechanically Treated (TMT) bars Fe-500 grade for all diameters. 20.00 Kgs 89.12

27 Compressor test of tube well by air compressor of 600 CFM / 150 PSI capacity in all districts. 2.00 Hour 3893.00

Labour charges for repairing leakage/ Jointing in CI/DI pipeline or Sluice Valve of following diameter at different places including

necessary excavation manually or by machinery, removing of mud, dewatering, cleaning of pipe, cutting of pipe, Jointing & repairing

using CID joints including CID joints, rubber rings, nut bolts, hiring excavator, Hydra/ Crane, dewatering machine, fuel, operator etc

complete (including cost of jointing material but excluding cost of pipe). 100mm. 2.00 No. 2068.85

Labour charges for repairing of leakage/ Jointing in PVC pipeline of following dia meter at different places including necessary

excavation manually or by mechanise excavation, dewatering removing of mud, cleaning of pipe and leakage portion, cutting the

pipeline & removing piece of pipe from trench with inclusive of mechanical devices JCB, Hydra/Crain if necessary & labours required

with providing material such couplers, solution etc. comp. (incl. all material but Exclu. cost of pipe). 110mm. 2.00 No. 1124.70

SBD SECTION-7 BILL OF QUANTITIES-323

Description of Items Qty. Unit Material + Amount (Rs.)

Supply and installation of MS fabricated structure cabin @ site of work using 65 mm, 50 mm & 25 mm square pipes with cabin size

1.5 mtr x 1.5 mtr x 2.13 mtr including providing & fitting of (1) backalite sheet 3.5mm thick in sides, (2) 20 guage MS sheet outer side

for side walls, (3) backalite sheet 3.5 mm thick sheet for roof side, (4) 24 guage GI sheet out side with 15 mm plywood sandwitch

30 fitting & flooring with 19 mm water proof plywood sheet and (5) shock proof rubber mating. Job includes oil painting two coats, door

locking handle arrangement, providing proper air ventilation and fuse box. The meter & fuse box should be fitted on timber hold fast

for holding screw or nut bolts by semi skilled labour as per detailed technical specifications, drawings and instructions of the Engineer-

in-charge. 1.00 Job 69930.00

Add 2% For Contengency Charges.

Add 1% For Labor Cess.

Total Project Cost Rs.

SBD SECTION-7 BILL OF QUANTITIES-324

CHAKLASI MUNICIPALITY, CHAKLASI

S.I.T.C OF 10 HP SUBMERSIBLE PUMPING MACHINERY WITH ALL COMPONENTS & ACCESSORIES AT JADAVPURA SAMANYA TEKRI (VIRANYA) AT WARD 06 AT CHAKLASI.

Description of Items Qty. Unit Amount (Rs.)

Lifting of submersible motor pump set complete with required No .& size of casing pipes by means of proper chain pulley block and pipe.

wrenches. Job includes stacking of pipes chronologically after due checking of threads. Up to 60 mtrs. 1.00 Nos. 1711.95

S.I.T.C. submersible pump set for bore of 150 mm. dia. or, more having 3 phase motor capacity not more than 10 H.P. and discharge

2 capacity having, Lifting and Lowering taken extra. 10 stage 575 to 480 LPM discharge at 60 to 70 mtr head for 65 mm dia delivery pipe.

Cat.III. 1.00 sets 39659.67

Lowering of submersible motor pump set at the depth of following, complete with required. Nos. and size of casing pipes erected by means of

3 proper chain pulley block & pipe wrenches after checking of threads of each pipe with coupling to take the load of the pump set and pipe

assembly filled up with water. Up to 60 mtrs. 1.00 Nos. 1711.95

Supplying & erecting approved make motor control cubical panel [Star delta] made from 16G CRCA sheet duly epoxy powder painted inside

and outside with hinged doors and locking with suitable size of ON - OFF isolator (AC 3 / 23 duty) main fuses. Digital volt and current meter

(in a single unit) with micro controller based control unit and current sensing single phasing preventer electronic overload protection, over

voltage (Programmable) protection and under voltage (Programmable) protection, prod less dry run protection programming facility for setting

of all parameter like overload current, high voltage limit, low voltage limit, dry run limit with digital indication on seven segment LED display for

any fault like over load, high voltage, low voltage, dry running single crimped, electronic star delta timer, feather touch start / stop push

buttons to be erected on angle iron frame. Grouted on wall the contactors will be of L& T, Siemens, BCH make only). S/D up to 10 HP.

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible Submersible copper cable approved make of following Size.

1 R x 3 Core x 2.5 Sq. mm. 80.00 Mtr. 104.03

1 R x 3 Core x 4 Sq. mm. 50.00 Mtr. 146.45

Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe Technology as

per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising, Inner pipe

dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded by highly

conductive compound with high charge dissipation suitable for following type of applications with chamber and heavy duty cover.

(A)(approved make OEM has to submit test certificate including value of earth resistance of installation duly stamped and signed by agency

and officer Incharge has to ensure the value of earthing resistane mentioned in test Certificate) & having back filling compound of (B) Inner

6 chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no load & dry form,

Sulphar content:- <2%(C) Back fill Compound :- Earthing compound should be capable to retain moisture for long time Necessary test

report must be submitted by Agency. For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT panel board, Motors

etc. using proper clamp. 20.00 Kg. 97.00

SBD SECTION-7 BILL OF QUANTITIES-325

Description of Items Qty. Unit Amount (Rs.)

Providing & erecting motor protection circuit breaker with shock proof enclosure (IP 65) erected as per direction for following motor HP

phase 440V A.C. up to 7.5 HP / 10 HP 12 to 18 Amp. 1.00 No 4803.56

Providing Water proof straight Joint in PVC insulated flat flexible copper cable by using insulating material, water proofing material & making

the joint complete. Up to 10 Sq. mm. 4.00 No 189.88

10 Supplying of following size of HEAVY UPVC column pipe with coupler and wire lock. For 80mm. 30.50 Rmt. 698.92

Providing and supplying in standard length ISI mark rigid unplasticised PVC pipes suitable for potable water with ring fit joint including cost of

rings, as per IS specification no. 4985/1988 including all local and central taxes, transportation, freight charges, octroi, inspection charges,

11 loading, unloading, conveyance to the departmental stores and including cost of jointing meterial etc. complete. Note : One coupler / ring

shall be provided with each full length pipe cost of which is included in rates below. Test Pressure 10 Kg/cm2. 110mm PVC Pipes.

Lowering, laying, fixing and jointing PVC/uPVC/cPVC pipes and specials of following class and diameter including cost of conveyance from

12 stores to site of works including cost of labour, material, cement solvent, giving satisfactory hydraulic testing as per ISI code. 80/75mm Dia

PVC Pipes 30.50 Rmt. 17.25

100/110mm Dia PVC Pipe 50.00 Rmt. 21.85

Supplying ISI Marked (Embossed) following size of Heavy duty “C” Class G.I. Pipe & erecting as directed by Engineer-in-charge with

necessary plumbing as desired. 100mm. 10.00 Rmt. 804.97

Supply of following size of TOP & BOTTOM accessories i.e. Adaptor set (CI) long, pump guard set, starter pipe Rubber ring for submersible

pump & UPVC column pipe as directed by Engineer - in - charge with necessary plumbing as desired. 80mm. 1.00 No 2681.55

15 Supplying & erecting G.l. bend for pipe connections suitable for 100mm. 1.00 No 548.43

Clamps made from MS plate with 3 holes on either side with nuts & bolts of standard make and suitable size. 450 mm X 65 mm X 10 mm flat

suitable to 65/80 mm dia. pipe. 1.00 No 574.79

Manufacture, Supply & Delivery of Ductile Iron Flange socket spigot bends, tees, reducers or any other specials as per BS-EN-545/1995

Class-A series K12 suitable for use with D.I. Pipes manufactured as per IS:8329/1994 delivery of specials is to be made to GWSSB store or

17 site of works any where in Gujarat including all taxes, loading, unloading, carting, stacking, insurance, inspection charges, octroi etc.

complete. With external bitumen & zinc coating & internal cement mortar lining. Socket & Spigot type. From 80 to 300mm Dia. Flange Ended.

Supplying & erecting Mild Steel heavy duty Flanges with rubber packing and hardware materials for pipe connections suitable for 100mm.

Providing and supplying at store or site of work incl. freight, loading, unloading, stacking, insaurance & all taxes etc. complete. P. V. C. Tee

(Moulded). 110 x 75 mm. 1.00 No 338.00

P. V. C. Reducer. 110 x 75 mm. 1.00 No 182.00

P. V. C. Bend 90° Moulded heavy. 110mm 1.00 No 519.00

Providing and Supplying ISI mark CI D/F Sluice valves, butterfly valves & Reflux valves of following class and diameter including all taxes,

insurance, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to departmental stores, stacking etc.

complete. Sluice valves as per IS - 780 & 2906 / 1984. Sluice Valve ISI Mark only. PN-1.6 With hand/wheel cap operated (Alt-1 type long

SBD SECTION-7 BILL OF QUANTITIES-326

Description of Items Qty. Unit Amount (Rs.)

Excavation for pipe line trenches for water supply, sewerage line, manhole etc. all with shoring and struting if required as per required

21 gradient and line including safety provisions using site rails and stacking excavated stuff including up to all required lead cleaning the site etc.

complete for all lifts and strata as specified. In all sort of soil and soft murrum. Upto 1.50 Mt. Depth. 48.00 Cmt. 102.35

Lowering, laying and jointing in position following C. I. / D/F Reflux valves, Butterfly valves, Sluice valves and Air valves including cost of all

labour, jointing material, including nut bolts and giving satisfactory hydraulic testing, etc. complete. For 100mm Dia. 1.00 Nos 504.85

Construction of valves chambers in brick or bela stone masonry, locally available in C. M. 1:6. Foundation concrete 150 mm thick in C. C.

1:4:8 of trap metal size 25 mm to 40 mm thick, inside cement plaster in C. M. 1:3 and cement pointing outside in C. M. 1:3 and top cover of

precast RCC slab 100 mm thick (with key hole in two parts, each with handles or MS Bar etc. complete as given size) Upto 1 Mt. depth from

G. L. to pipe invert level incl. complete civil works but excl. cost of excavation and refilling, with cast in situ RCC slab in one single piece with

fixing of CI-MH Frame and cover (excl. cost of CI-MH Frame and cover) with 23 mm thick brick masonry wall in C.M.1:6. Size of chamber

0.90 m x 0.90 m and 1.0 mt. deep. With precast slab in two parts 15 mm. 1.00 Nos 8898.70

24 CI Frame & Cover For Valve Chamber 100.00 Kg. 58.00

Providing and casting in situ C.C. in grade M-20 (proportions as per mix design or as per table9 of IS456 2000 in masses by weigh batching)

using granite, quartzite trap metal of size 6 mm to 20 mm for RCC work, including scaffolding centering, formwork, needle vibrated

25 consolidation, curing complete up to 6 meter depth or height (excluding cost of reinforcement and neat finishing) with centering and

shuttering/deshuttering etc. complete for structure other than water retaining (Below G.L). For Thrust Block. With Form Work.

26 Refilling the pipeline trenches incl. ramming, watering, consolidating desposal of surplus stuff as directed within a radius of 3 km. 48.00 Cmt. 25.30

Supplying cutting, bending, binding and placing in position steel as per plan and design and as per ISS 2502 including cost of steel and

27 binding wire for reserviors/structures only including lift up to 6 meter height or depth below G.L. for all diameters. Do-Thermo mechanically

Treated (TMT) bars Fe-500 grade for all diameters. 20.00 Kgs 89.12

28 Compressor test of tube well by air compressor of 600 CFM / 150 PSI capacity in all districts. 2.00 Hour 3893.00

Labour charges for repairing leakage/ Jointing in CI/DI pipeline or Sluice Valve of following diameter at different places including necessary

excavation manually or by machinery, removing of mud, dewatering, cleaning of pipe, cutting of pipe, Jointing & repairing using CID joints

including CID joints, rubber rings, nut bolts, hiring excavator, Hydra/ Crane, dewatering machine, fuel, operator etc complete (including cost

of jointing material but excluding cost of pipe). 100mm. 2.00 No. 2068.85

Labour charges for repairing of leakage/ Jointing in PVC pipeline of following dia meter at different places including necessary excavation

manually or by mechanise excavation, dewatering removing of mud, cleaning of pipe and leakage portion, cutting the pipeline & removing

piece of pipe from trench with inclusive of mechanical devices JCB, Hydra/Crain if necessary & labours required with providing material such

couplers, solution etc. comp. (incl. all material but Exclu. cost of pipe). 110mm. 2.00 No. 1124.70

SBD SECTION-7 BILL OF QUANTITIES-327

Description of Items Qty. Unit Amount (Rs.)

Supply and installation of MS fabricated structure cabin @ site of work using 65 mm, 50 mm & 25 mm square pipes with cabin size 1.5 mtr x

1.5 mtr x 2.13 mtr including providing & fitting of (1) backalite sheet 3.5mm thick in sides, (2) 20 guage MS sheet outer side for side walls, (3)

backalite sheet 3.5 mm thick sheet for roof side, (4) 24 guage GI sheet out side with 15 mm plywood sandwitch fitting & flooring with 19 mm

31 water proof plywood sheet and (5) shock proof rubber mating. Job includes oil painting two coats, door locking handle arrangement, providing

proper air ventilation and fuse box. The meter & fuse box should be fitted on timber hold fast for holding screw or nut bolts by semi skilled

labour as per detailed technical specifications, drawings and instructions of the Engineer-in-charge. 1.00 Job 69930.00

Add 2% For Contengency Charges.

Add 1% For Labor Cess.

Total Project Cost Rs.

SBD SECTION-7 BILL OF QUANTITIES-328

CHAKLASI MUNICIPALITY, CHAKLASI

S.I.T.C OF 15 HP SUBMERSIBLE PUMPING MACHINERY WITH ALL COMPONENTS & ACCESSORIES AT JADAVPURA ASHRAM AT WARD 06 AT CHAKLASI.

Description of Items Qty. Unit Amount (Rs.)

Lifting of submersible motor pump set complete with required No .& size of casing pipes by means of proper chain pulley block

1 and pipe. wrenches. Job includes stacking of pipes chronologically after due checking of threads. Up to 60 mtrs.

S.I.T.C. submersible pump set for bore of 150 mm. dia. or, more having 3 phase motor capacity not more than 15 H.P. and

2 discharge capacity having, Lifting and Lowering taken extra. (8 stage) 695 to 492 L.P.M. at the head 48 to 73 mtrs suitable for 65/50

mm dia. delivery pipe. Cat.III. 1.00 sets 49939.45

Lowering of submersible motor pump set at the depth of following, complete with required. Nos. and size of casing pipes erected by

3 means of proper chain pulley block & pipe wrenches after checking of threads of each pipe with coupling to take the load of the

pump set and pipe assembly filled up with water. Up to 60 mtrs. 1.00 Nos. 1711.95

Supplying & erecting approved make motor control cubical panel [Star delta] made from 16G CRCA sheet duly epoxy powder

painted inside and outside with hinged doors and locking with suitable size of ON - OFF isolator (AC 3 / 23 duty) main fuses. Digital

volt and current meter (in a single unit) with micro controller based control unit and current sensing single phasing preventer

electronic overload protection, over voltage (Programmable) protection and under voltage (Programmable) protection, prod less dry

run protection programming facility for setting of all parameter like overload current, high voltage limit, low voltage limit, dry run limit

with digital indication on seven segment LED display for any fault like over load, high voltage, low voltage, dry running single

crimped, electronic star delta timer, feather touch start / stop push buttons to be erected on angle iron frame. Grouted on wall the

contactors will be of L& T, Siemens, BCH make only). S/D up to 15 HP. 1.00 No 16053.95

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible Submersible copper cable approved make of

following Size.

1 R x 3 Core x 4 Sq. mm. 80.00 Mtr. 146.45

1 R x 3 Core x 6 Sq. mm. 30.00 Mtr. 172.71

Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe

Technology as per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200

Micron galvanising, Inner pipe dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant

ohmic value surrounded by highly conductive compound with high charge dissipation suitable for following type of applications with

chamber and heavy duty cover. (A)(approved make OEM has to submit test certificate including value of earth resistance of

installation duly stamped and signed by agency and officer Incharge has to ensure the value of earthing resistane mentioned in test

6 Certificate) & having back filling compound of (B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC

62561-2017, Voltage drop :- < 1 volt at no load & dry form, Sulphar content:- <2% (C) Back fill Compound :- Earthing compound

should be capable to retain moisture for long time Necessary test report must be submitted by Agency. For Electrical Installation up

to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg. 1.00 No 4591.46

Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T., OCB/ ACB/ Transformer LT panel board,

Motors etc. using proper clamp. 20.00 Kg. 97.00

SBD SECTION-7 BILL OF QUANTITIES-329

Description of Items Qty. Unit Amount (Rs.)

Providing & erecting motor protection circuit breaker with shock proof enclosure (IP 65) erected as per direction for following motor

HP 3 phase 440V A.C. up to 15 HP 18 to 26 Amp. 1.00 No 5230.79

Providing Water proof straight Joint in PVC insulated flat flexible copper cable by using insulating material, water proofing material &

making the joint complete. Up to 10 Sq. mm. 4.00 No 189.88

10 Supplying of following size of HEAVY UPVC column pipe with coupler and wire lock. For 100mm. 30.50 Rmt. 1130.19

Providing and supplying in standard length ISI mark rigid unplasticised PVC pipes suitable for potable water with ring fit joint

including cost of rings, as per IS specification no. 4985/1988 including all local and central taxes, transportation, freight charges,

11 octroi, inspection charges, loading, unloading, conveyance to the departmental stores and including cost of jointing meterial etc.

complete. Note : One coupler / ring shall be provided with each full length pipe cost of which is included in rates below. Test

Pressure 10 Kg/cm2. 110mm PVC Pipes. 50.00 Rmt. 320.00

Lowering, laying, fixing and jointing PVC/uPVC/cPVC pipes and specials of following class and diameter including cost of

12 conveyance from stores to site of works including cost of labour, material, cement solvent, giving satisfactory hydraulic testing as

per ISI code. 100/110mm Dia PVC Pipes 80.50 Rmt. 21.85

Supplying ISI Marked (Embossed) following size of Heavy duty “C” Class G.I. Pipe & erecting as directed by Engineer-in-charge with

necessary plumbing as desired. 100mm. 10.00 Rmt. 804.97

Supply of following size of TOP & BOTTOM accessories i.e. Adaptor set (CI) long, pump guard set, starter pipe Rubber ring for

14 submersible pump & UPVC column pipe as directed by Engineer - in - charge with necessary plumbing as desired. 100mm.

15 Supplying & erecting G.l. bend for pipe connections suitable for 100mm. 1.00 No 548.43

Clamps made from MS plate with 3 holes on either side with nuts & bolts of standard make and suitable size. 450 mm X 65 mm X

10 mm flat suitable to 100/125 mm dia. pipe. 1.00 No 693.94

Supplying & erecting Mild Steel heavy duty Flanges with rubber packing and hardware materials for pipe connections suitable for

SBD SECTION-7 BILL OF QUANTITIES-330

Description of Items Qty. Unit Amount (Rs.)

Providing and supplying at store or site of work incl. freight, loading, unloading, stacking, insaurance & all taxes etc. complete. P. V.

C. Tee (Moulded). 110 x 110 mm. 1.00 No 407.00

P.V.C Reducer. 110x75mm 2.00 No 182.00

P. V. C. Bend 90° Moulded heavy. 110mm 2.00 No 519.00

Excavation for pipe line trenches for water supply, sewerage line, manhole etc. all with shoring and struting if required as per

required gradient and line including safety provisions using site rails and stacking excavated stuff including up to all required lead

cleaning the site etc. complete for all lifts and strata as specified. In all sort of soil and soft murrum. Upto 1.50 Mt. Depth.

Providing and casting in situ C.C. in grade M-20 (proportions as per mix design or as per table9 of IS456 2000 in masses by weigh

batching) using granite, quartzite trap metal of size 6 mm to 20 mm for RCC work, including scaffolding centering, formwork, needle

20 vibrated consolidation, curing complete up to 6 meter depth or height (excluding cost of reinforcement and neat finishing) with

centering and shuttering/deshuttering etc. complete for structure other than water retaining (Below G.L). For Thrust Block. With

Form Work. 0.50 Cmt. 6348.00

Refilling the pipeline trenches incl. ramming, watering, consolidating desposal of surplus stuff as directed within a radius of 3 km.

Supplying cutting, bending, binding and placing in position steel as per plan and design and as per ISS 2502 including cost of steel

22 and binding wire for reserviors/structures only including lift up to 6 meter height or depth below G.L. for all diameters. Do-Thermo

mechanically Treated (TMT) bars Fe-500 grade for all diameters. 20.00 Kgs 89.12

23 Compressor test of tube well by air compressor of 600 CFM / 150 PSI capacity in all districts. 2.00 Hour 3893.00

Labour charges for repairing leakage/ Jointing in CI/DI pipeline or Sluice Valve of following diameter at different places including

necessary excavation manually or by machinery, removing of mud, dewatering, cleaning of pipe, cutting of pipe, Jointing & repairing

using CID joints including CID joints, rubber rings, nut bolts, hiring excavator, Hydra/ Crane, dewatering machine, fuel, operator etc

complete (including cost of jointing material but excluding cost of pipe). 100mm. 2.00 No. 2068.85

Labour charges for repairing of leakage/ Jointing in PVC pipeline of following dia meter at different places including necessary

excavation manually or by mechanise excavation, dewatering removing of mud, cleaning of pipe and leakage portion, cutting the

25 pipeline & removing piece of pipe from trench with inclusive of mechanical devices JCB, Hydra/Crain if necessary & labours

required with providing material such couplers, solution etc. comp. (incl. all material but Exclu. cost of pipe). 110mm.

SBD SECTION-7 BILL OF QUANTITIES-331

Description of Items Qty. Unit Amount (Rs.)

Supply and installation of MS fabricated structure cabin @ site of work using 65 mm, 50 mm & 25 mm square pipes with cabin size

1.5 mtr x 1.5 mtr x 2.13 mtr including providing & fitting of (1) backalite sheet 3.5mm thick in sides, (2) 20 guage MS sheet outer

side for side walls, (3) backalite sheet 3.5 mm thick sheet for roof side, (4) 24 guage GI sheet out side with 15 mm plywood

26 sandwitch fitting & flooring with 19 mm water proof plywood sheet and (5) shock proof rubber mating. Job includes oil painting two

coats, door locking handle arrangement, providing proper air ventilation and fuse box. The meter & fuse box should be fitted on

timber hold fast for holding screw or nut bolts by semi skilled labour as per detailed technical specifications, drawings and

instructions of the Engineer-in-charge. 1.00 Job 69930.00

Add 2% For Contengency Charges.

Add 1% For Labor Cess.

Total Project Cost Rs.

SBD SECTION-7 BILL OF QUANTITIES-332

CHAKLASI MUNICIPALITY, CHAKLASI

S.I.T.C OF 15 HP SUBMERSIBLE PUMPING MACHINERY WITH ALL COMPONENTS & ACCESSORIES AT SADIPURA KHODIYAR MATA MANDIR AT WARD 07 AT CHAKLASI.

Description of Items Qty. Unit Amount (Rs.)

Lifting of submersible motor pump set complete with required No .& size of casing pipes by means of proper chain pulley block and

pipe. wrenches. Job includes stacking of pipes chronologically after due checking of threads. Up to 60 mtrs. 1.00 Nos. 1711.95

S.I.T.C. submersible pump set for bore of 150 mm. dia. or, more having 3 phase motor capacity not more than 15 H.P. and discharge

2 capacity having, Lifting and Lowering taken extra. (8 stage) 695 to 492 L.P.M. at the head 48 to 73 mtrs suitable for 65/50 mm dia.

delivery pipe. Cat.III. 1.00 sets 49939.45

Lowering of submersible motor pump set at the depth of following, complete with required. Nos. and size of casing pipes erected by

3 means of proper chain pulley block & pipe wrenches after checking of threads of each pipe with coupling to take the load of the pump set

and pipe assembly filled up with water. Up to 60 mtrs. 1.00 Nos. 1711.95

Supplying & erecting approved make motor control cubical panel [Star delta] made from 16G CRCA sheet duly epoxy powder painted

inside and outside with hinged doors and locking with suitable size of ON - OFF isolator (AC 3 / 23 duty) main fuses. Digital volt and

current meter (in a single unit) with micro controller based control unit and current sensing single phasing preventer electronic overload

protection, over voltage (Programmable) protection and under voltage (Programmable) protection, prod less dry run protection

programming facility for setting of all parameter like overload current, high voltage limit, low voltage limit, dry run limit with digital indication

on seven segment LED display for any fault like over load, high voltage, low voltage, dry running single crimped, electronic star delta

timer, feather touch start / stop push buttons to be erected on angle iron frame. Grouted on wall the contactors will be of L& T, Siemens,

BCH make only). S/D up to 15 HP. 1.00 No 16053.95

Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible Submersible copper cable approved make of following Size.

1 R x 3 Core x 4 Sq. mm. 80.00 Mtr. 146.45

1 R x 3 Core x 6 Sq. mm. 30.00 Mtr. 172.71

Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe Technology as

per IS 3043-1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising, Inner

pipe dia of 25 mm having 200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded by highly

conductive compound with high charge dissipation suitable for following type of applications with chamber and heavy duty cover.

(A)(approved make OEM has to submit test certificate including value of earth resistance of installation duly stamped and signed by

agency and officer Incharge has to ensure the value of earthing resistane mentioned in test Certificate) & having back filling compound of

6 (B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no load &

dry form, Sulphar content:- <2%(C) Back fill Compound :- Earthing compound should be capable to retain moisture for long time

Necessary test report must be submitted by Agency. For Electrical Installation up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT panel board,

Motors etc. using proper clamp. 20.00 Kg. 97.00

SBD SECTION-7 BILL OF QUANTITIES-333

Description of Items Qty. Unit Amount (Rs.)

Providing & erecting motor protection circuit breaker with shock proof enclosure (IP 65) erected as per direction for following motor HP

phase 440V A.C. up to 15 HP 18 to 26 Amp. 1.00 No 5230.79

Providing Water proof straight Joint in PVC insulated flat flexible copper cable by using insulating material, water proofing material &

making the joint complete. Up to 10 Sq. mm. 4.00 No 189.88

10 Supplying of following size of HEAVY UPVC column pipe with coupler and wire lock. For 100mm. 30.50 Rmt. 1130.19

Providing and supplying in standard length ISI mark rigid unplasticised PVC pipes suitable for potable water with ring fit joint including cost

of rings, as per IS specification no. 4985/1988 including all local and central taxes, transportation, freight charges, octroi, inspection

11 charges, loading, unloading, conveyance to the departmental stores and including cost of jointing meterial etc. complete. Note : One

coupler / ring shall be provided with each full length pipe cost of which is included in rates below. Test Pressure 10 Kg/cm2. 110mm PVC

Pipes. 30.00 Rmt. 320.00

Lowering, laying, fixing and jointing PVC/uPVC/cPVC pipes and specials of following class and diameter including cost of conveyance

12 from stores to site of works including cost of labour, material, cement solvent, giving satisfactory hydraulic testing as per ISI code.

100/110mm Dia PVC Pipes 60.50 Rmt. 21.85

Supplying ISI Marked (Embossed) following size of Heavy duty “C” Class G.I. Pipe & erecting as directed by Engineer-in-charge with

necessary plumbing as desired. 100mm. 10.00 Rmt. 804.97

Providing and fixing flanged D.I.D.F. / Class K-9 pipes vertically for RCC. Reservoir incl. providing clamps at every 3 mt incl. jointing

materials such as nuts, bolts, rubber packing, hydraulic testing and necessary scaffolding etc. complete. 100mm. 30.00 Rmt. 2684.10

Supply of following size of TOP & BOTTOM accessories i.e. Adaptor set (CI) long, pump guard set, starter pipe Rubber ring for

submersible pump & UPVC column pipe as directed by Engineer - in - charge with necessary plumbing as desired. 100mm. 1.00 No 3872.34

16 Supplying & erecting G.l. bend for pipe connections suitable for 100mm. 1.00 No 548.43

Clamps made from MS plate with 3 holes on either side with nuts & bolts of standard make and suitable size. 450 mm X 65 mm X 10 mm

flat suitable to 100/125 mm dia. pipe. 1.00 No 693.94

Manufacture, Supply & Delivery of Ductile Iron Flange socket spigot bends, tees, reducers or any other specials as per BS-EN-545/1995

Class-A series K12 suitable for use with D.I. Pipes manufactured as per IS:8329/1994 delivery of specials is to be made to GWSSB store

18 or site of works any where in Gujarat including all taxes, loading, unloading, carting, stacking, insurance, inspection charges, octroi etc.

complete. With external bitumen & zinc coating & internal cement mortar lining. Socket & Spigot type. From 80 to 300mm Dia. Flange

Ended. 60.00 Kgs. 151.00

Supplying & erecting Mild Steel heavy duty Flanges with rubber packing and hardware materials for pipe connections suitable for 100mm.

SBD SECTION-7 BILL OF QUANTITIES-334

Description of Items Qty. Unit Amount (Rs.)

Providing and supplying at store or site of work incl. freight, loading, unloading, stacking, insaurance & all taxes etc. complete. P. V. C.

Tee (Moulded). 110 x 75 mm. 1.00 No 338.00

P. V. C. Reducer. 110 x 75 mm. 1.00 No 182.00

P. V. C. Bend 90° Moulded heavy. 110mm 1.00 No 519.00

Providing and Supplying ISI mark CI D/F Sluice valves, butterfly valves & Reflux valves of following class and diameter including all taxes,

insurance, transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to departmental stores, stacking etc.

complete. Sluice valves as per IS - 780 & 2906 / 1984. Sluice Valve ISI Mark only. PN-1.6 With hand/wheel cap operated (Alt-1 type long

Excavation for pipe line trenches for water supply, sewerage line, manhole etc. all with shoring and struting if required as per required

22 gradient and line including safety provisions using site rails and stacking excavated stuff including up to all required lead cleaning the site

etc. complete for all lifts and strata as specified. In all sort of soil and soft murrum. Upto 1.50 Mt. Depth. 10.00 Cmt. 102.35

Lowering, laying and jointing in position following C. I. / D/F Reflux valves, Butterfly valves, Sluice valves and Air valves including cost of

all labour, jointing material, including nut bolts and giving satisfactory hydraulic testing, etc. complete. For 100mm Dia. 1.00 Nos 504.85

Construction of valves chambers in brick or bela stone masonry, locally available in C. M. 1:6. Foundation concrete 150 mm thick in C. C.

1:4:8 of trap metal size 25 mm to 40 mm thick, inside cement plaster in C. M. 1:3 and cement pointing outside in C. M. 1:3 and top cover

of precast RCC slab 100 mm thick (with key hole in two parts, each with handles or MS Bar etc. complete as given size) Upto 1 Mt. depth

24 from G. L. to pipe invert level incl. complete civil works but excl. cost of excavation and refilling, with cast in situ RCC slab in one single

piece with fixing of CI-MH Frame and cover (excl. cost of CI-MH Frame and cover) with 23 mm thick brick masonry wall in C.M.1:6. Size

of chamber 0.90 m x 0.90 m and 1.0 mt. deep. With precast slab in two parts 15 mm.

25 CI Frame & Cover For Valve Chamber 100.00 Kg. 58.00

Providing and casting in situ C.C. in grade M-20 (proportions as per mix design or as per table9 of IS456 2000 in masses by weigh

batching) using granite, quartzite trap metal of size 6 mm to 20 mm for RCC work, including scaffolding centering, formwork, needle

26 vibrated consolidation, curing complete up to 6 meter depth or height (excluding cost of reinforcement and neat finishing) with centering

and shuttering/deshuttering etc. complete for structure other than water retaining (Below G.L). For Thrust Block. With Form Work.

27 Refilling the pipeline trenches incl. ramming, watering, consolidating desposal of surplus stuff as directed within a radius of 3 km. 10.00 Cmt. 25.30

Supplying cutting, bending, binding and placing in position steel as per plan and design and as per ISS 2502 including cost of steel and

28 binding wire for reserviors/structures only including lift up to 6 meter height or depth below G.L. for all diameters. Do-Thermo mechanically

Treated (TMT) bars Fe-500 grade for all diameters. 20.00 Kgs 89.12

29 Compressor test of tube well by air compressor of 600 CFM / 150 PSI capacity in all districts. 2.00 Hour 3893.00

Labour charges for repairing leakage/ Jointing in CI/DI pipeline or Sluice Valve of following diameter at different places including

necessary excavation manually or by machinery, removing of mud, dewatering, cleaning of pipe, cutting of pipe, Jointing & repairing using

CID joints including CID joints, rubber rings, nut bolts, hiring excavator, Hydra/ Crane, dewatering machine, fuel, operator etc complete

(including cost of jointing material but excluding cost of pipe). 100mm. 2.00 No. 2068.85

SBD SECTION-7 BILL OF QUANTITIES-335

Description of Items Qty. Unit Amount (Rs.)

Labour charges for repairing of leakage/ Jointing in PVC pipeline of following dia meter at different places including necessary excavation

manually or by mechanise excavation, dewatering removing of mud, cleaning of pipe and leakage portion, cutting the pipeline & removing

piece of pipe from trench with inclusive of mechanical devices JCB, Hydra/Crain if necessary & labours required with providing material

such couplers, solution etc. comp. (incl. all material but Exclu. cost of pipe). 110mm. 2.00 No. 1124.70

Add 2% For Contengency Charges.

Add 1% For Labor Cess.

Total Project Cost Rs.

SBD SECTION-7 BILL OF QUANTITIES-336

CHAKLASI MUNICIPALITY, CHAKLASI

S.I.T.C OF 10 HP SUBMERSIBLE PUMPING MACHINERY WITH ALL COMPONENTS & ACCESSORIES AT BHAIJIPURA AT WARD 07 AT CHAKLASI.

Description of Items Qty. Unit Amount (Rs.)

Lifting of submersible motor pump set complete with required No .& size of casing pipes by means of proper chain pulley block and pipe.

wrenches. Job includes stacking of pipes chronologically after due checking of threads. Up to 60 mtrs. 1.00 Nos. 1711.95

S.I.T.C. submersible pump set for bore of 150 mm. dia. or, more having 3 phase motor capacity not more than 10 H.P. and discharge capacity

2 having, Lifting and Lowering taken extra. 10 stage 575 to 480 LPM discharge at 60 to 70 mtr head for 65 mm dia delivery pipe. Cat.III.

Lowering of submersible motor pump set at the depth of following, complete with required. Nos. and size of casing pipes erected by means of proper

3 chain pulley block & pipe wrenches after checking of threads of each pipe with coupling to take the load of the pump set and pipe assembly filled up

with water. Up to 60 mtrs. 1.00 Nos. 1711.95

Supplying & erecting approved make motor control cubical panel [Star delta] made from 16G CRCA sheet duly epoxy powder painted inside and

outside with hinged doors and locking with suitable size of ON - OFF isolator (AC 3 / 23 duty) main fuses. Digital volt and current meter (in a single

unit) with micro controller based control unit and current sensing single phasing preventer electronic overload protection, over voltage

4 (Programmable) protection and under voltage (Programmable) protection, prod less dry run protection programming facility for setting of all parameter

like overload current, high voltage limit, low voltage limit, dry run limit with digital indication on seven segment LED display for any fault like over load,

high voltage, low voltage, dry running single crimped, electronic star delta timer, feather touch start / stop push buttons to be erected on angle iron

frame. Grouted on wall the contactors will be of L& T, Siemens, BCH make only). S/D up to 10 HP.

5 Providing and erecting ISI marked PVC insulated PVC Sheathed Flat flexible Submersible copper cable approved make of following Size.

1 R x 3 Core x 2.5 Sq. mm. 80.00 Mtr. 104.03

1 R x 3 Core x 4 Sq. mm. 50.00 Mtr. 146.45

Supplying & erecting earth pit of minimum bore dia.150mm size approved make Earthing Electrode consisting Pipe-in-Pipe Technology as per IS

3043-1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of 50mm having 80-200 Micron galvanising, Inner pipe dia of 25 mm

having 200-250 Micron galvanising, connection terminal dia of 12mm with constant ohmic value surrounded by highly conductive compound with high

charge dissipation suitable for following type of applications with chamber and heavy duty cover. (A)(approved make OEM has to submit test

certificate including value of earth resistance of installation duly stamped and signed by agency and officer Incharge has to ensure the value of

6 earthing resistane mentioned in test Certificate) & having back filling compound of (B) Inner chemical (CCM Compound)- Resistivity:- 0.2 ohm / meter

testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no load & dry form, Sulphar content:- <2%(C) Back fill Compound :- Earthing compound

should be capable to retain moisture for long time Necessary test report must be submitted by Agency. For Electrical Installation up to 440V in

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Providing and erecting required size HOT deep Galvanised iron strip for earthing of H.T. , OCB/ ACB/ Transformer LT panel board, Motors etc. using

proper clamp. 20.00 Kg. 97.00

Providing & erecting motor protection circuit breaker with shock proof enclosure (IP 65) erected as per direction for following motor HP 3 phase 440V

A.C. up to 7.5 HP / 10 HP 12 to 18 Amp. 1.00 No 4803.56

SBD SECTION-7 BILL OF QUANTITIES-337

Description of Items Qty. Unit Amount (Rs.)

Providing Water proof straight Joint in PVC insulated flat flexible copper cable by using insulating material, water proofing material & making the joint

complete. Up to 10 Sq. mm. 4.00 No 189.88

10 Supplying of following size of HEAVY UPVC column pipe with coupler and wire lock. For 80mm. 30.50 Rmt. 698.92

Providing and supplying in standard length ISI mark rigid unplasticised PVC pipes suitable for potable water with ring fit joint including cost of rings, as

per IS specification no. 4985/1988 including all local and central taxes, transportation, freight charges, octroi, inspection charges, loading, unloading,

conveyance to the departmental stores and including cost of jointing meterial etc. complete. Note : One coupler / ring shall be provided with each full

length pipe cost of which is included in rates below. Test Pressure 10 Kg/cm2. 110mm PVC Pipes. 50.00 Rmt. 320.00

Lowering, laying, fixing and jointing PVC/uPVC/cPVC pipes and specials of following class and diameter including cost of conveyance from stores to

12 site of works including cost of labour, material, cement solvent, giving satisfactory hydraulic testing as per ISI code. 80/75mm Dia PVC Pipes

100/110mm Dia PVC Pipe 50.00 Rmt. 21.85

Supplying ISI Marked (Embossed) following size of Heavy duty “C” Class G.I. Pipe & erecting as directed by Engineer-in-charge with necessary

plumbing as desired. 100mm. 10.00 Rmt. 804.97

Supply of following size of TOP & BOTTOM accessories i.e. Adaptor set (CI) long, pump guard set, starter pipe Rubber ring for submersible pump &

UPVC column pipe as directed by Engineer - in - charge with necessary plumbing as desired. 80mm. 1.00 No 2681.55

15 Supplying & erecting G.l. bend for pipe connections suitable for 100mm. 1.00 No 548.43

Clamps made from MS plate with 3 holes on either side with nuts & bolts of standard make and suitable size. 450 mm X 65 mm X 10 mm flat suitable

to 65/80 mm dia. pipe. 1.00 No 574.79

Manufacture, Supply & Delivery of Ductile Iron Flange socket spigot bends, tees, reducers or any other specials as per BS-EN-545/1995 Class-A

series K12 suitable for use with D.I. Pipes manufactured as per IS:8329/1994 delivery of specials is to be made to GWSSB store or site of works any

17 where in Gujarat including all taxes, loading, unloading, carting, stacking, insurance, inspection charges, octroi etc. complete. With external bitumen &

zinc coating & internal cement mortar lining. Socket & Spigot type. From 80 to 300mm Dia. Flange Ended.

18 Supplying & erecting Mild Steel heavy duty Flanges with rubber packing and hardware materials for pipe connections suitable for 100mm. 4.00 No 212.10

Providing and supplying at store or site of work incl. freight, loading, unloading, stacking, insaurance & all taxes etc. complete. P. V. C. Tee

(Moulded). 110 x 75 mm. 1.00 No 338.00

P. V. C. Reducer. 110 x 75 mm. 1.00 No 182.00

P. V. C. Bend 90° Moulded heavy. 110mm 1.00 No 519.00

Providing and Supplying ISI mark CI D/F Sluice valves, butterfly valves & Reflux valves of following class and diameter including all taxes, insurance,

transportation, freight charges, octroi, inspection charges, loading, unloading, conveyance to departmental stores, stacking etc. complete. Sluice

valves as per IS - 780 & 2906 / 1984. Sluice Valve ISI Mark only. PN-1.6 With hand/wheel cap operated (Alt-1 type long body). 100mm.

Excavation for pipe line trenches for water supply, sewerage line, manhole etc. all with shoring and struting if required as per required gradient and

21 line including safety provisions using site rails and stacking excavated stuff including up to all required lead cleaning the site etc. complete for all lifts

and strata as specified. In all sort of soil and soft murrum. Upto 1.50 Mt. Depth. 48.00 Cmt. 102.35

SBD SECTION-7 BILL OF QUANTITIES-338

Description of Items Qty. Unit Amount (Rs.)

Lowering, laying and jointing in position following C. I. / D/F Reflux valves, Butterfly valves, Sluice valves and Air valves including cost of all labour,

jointing material, including nut bolts and giving satisfactory hydraulic testing, etc. complete. For 100mm Dia. 1.00 Nos 504.85

Construction of valves chambers in brick or bela stone masonry, locally available in C. M. 1:6. Foundation concrete 150 mm thick in C. C. 1:4:8 of trap

metal size 25 mm to 40 mm thick, inside cement plaster in C. M. 1:3 and cement pointing outside in C. M. 1:3 and top cover of precast RCC slab

mm thick (with key hole in two parts, each with handles or MS Bar etc. complete as given size) Upto 1 Mt. depth from G. L. to pipe invert level incl.

complete civil works but excl. cost of excavation and refilling, with cast in situ RCC slab in one single piece with fixing of CI-MH Frame and cover

(excl. cost of CI-MH Frame and cover) with 23 mm thick brick masonry wall in C.M.1:6. Size of chamber 0.90 m x 0.90 m and 1.0 mt. deep. With

precast slab in two parts 15 mm. 1.00 Nos 8898.70

24 CI Frame & Cover For Valve Chamber 100.00 Kg. 58.00

Providing and casting in situ C.C. in grade M-20 (proportions as per mix design or as per table9 of IS456 2000 in masses by weigh batching) using

granite, quartzite trap metal of size 6 mm to 20 mm for RCC work, including scaffolding centering, formwork, needle vibrated consolidation, curing

complete up to 6 meter depth or height (excluding cost of reinforcement and neat finishing) with centering and shuttering/deshuttering etc. complete

for structure other than water retaining (Below G.L). For Thrust Block. With Form Work. 0.50 Cmt. 6348.00

26 Refilling the pipeline trenches incl. ramming, watering, consolidating desposal of surplus stuff as directed within a radius of 3 km. 48.00 Cmt. 25.30

Supplying cutting, bending, binding and placing in position steel as per plan and design and as per ISS 2502 including cost of steel and binding wire

27 for reserviors/structures only including lift up to 6 meter height or depth below G.L. for all diameters. Do-Thermo mechanically Treated (TMT) bars Fe-

500 grade for all diameters. 20.00 Kgs 89.12

28 Compressor test of tube well by air compressor of 600 CFM / 150 PSI capacity in all districts. 2.00 Hour 3893.00

Labour charges for repairing leakage/ Jointing in CI/DI pipeline or Sluice Valve of following diameter at different places including necessary

excavation manually or by machinery, removing of mud, dewatering, cleaning of pipe, cutting of pipe, Jointing & repairing using CID joints including

CID joints, rubber rings, nut bolts, hiring excavator, Hydra/ Crane, dewatering machine, fuel, operator etc complete (including cost of jointing material

but excluding cost of pipe). 100mm. 2.00 No. 2068.85

Labour charges for repairing of leakage/ Jointing in PVC pipeline of following dia meter at different places including necessary excavation manually or

by mechanise excavation, dewatering removing of mud, cleaning of pipe and leakage portion, cutting the pipeline & removing piece of pipe from

trench with inclusive of mechanical devices JCB, Hydra/Crain if necessary & labours required with providing material such couplers, solution etc.

comp. (incl. all material but Exclu. cost of pipe). 110mm. 2.00 No. 1124.70

SBD SECTION-7 BILL OF QUANTITIES-339

Description of Items Qty. Unit Amount (Rs.)

Supply and installation of MS fabricated structure cabin @ site of work using 65 mm, 50 mm & 25 mm square pipes with cabin size 1.5 mtr x 1.5 mtr x

2.13 mtr including providing & fitting of (1) backalite sheet 3.5mm thick in sides, (2) 20 guage MS sheet outer side for side walls, (3) backalite sheet

3.5 mm thick sheet for roof side, (4) 24 guage GI sheet out side with 15 mm plywood sandwitch fitting & flooring with 19 mm water proof plywood

sheet and (5) shock proof rubber mating. Job includes oil painting two coats, door locking handle arrangement, providing proper air ventilation and

fuse box. The meter & fuse box should be fitted on timber hold fast for holding screw or nut bolts by semi skilled labour as per detailed technical

specifications, drawings and instructions of the Engineer-in-charge. 1.00 Job 69930.00

Add 2% For Contengency Charges.

Add 1% For Labor Cess.

Total Project Cost Rs.

SBD SECTION-7 BILL OF QUANTITIES-340