GE/SMB/T-30/2021-22 SPL REPAIR BLDG NO P 15 AND PROVN OF COVERED PARKING TILING IN KITCHEN TOILET OF BLDG NO P 26 P 33 P 44 AND P 70 AND ADDITIONAL ENTRY GATE SYSTEM AT MIL STN SAMBA

Amount

Demolition of plain cement concrete in ground floors or paving n.exc 15 cm thickness (Below or above ground level) complete all as specified and directed.

Demolition of brick work or stone masonry, built in cement mortar incl all quoins, arches pillars etc complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for , complete all as specified and directed.

Taking down cement plaster/Dado(terrazzo) on brick/concrete or stone walls, ceiling, etc, including raking out joints, hacking for key, scrugbbing down with water etc, complete all as specified and directed.

Dismanting of floor hearth or wall tiling including cement mortar bedding , removing serviceable tiles to store and rubbish off the premises , complete all as specified and directed.

Brick work with sub class 'B' burnt bricks straight or curved on plan exc. 6 m mean radius built in CM 1:6 complete all as specified and directed.

Plain cement concrete type B1 1:2:4 in lintels upto 1.5m clear span ,cills ,steps;seismic and other similar bands ,plinth courses ,parapets and railings upto 60cm in height. complete all as specified and directed.

RCC M-25 (using 20 mm graded stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves, chajjas. etc complete all as specified and directed.

Mild steel TMT bars 6 to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, chajjjas, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) incl fair finished surface complete all as specified and directed.

PCC 1:2:4 Type B-1 ( using 20mm graded crushed stone aggregate) as in coping/bed blocks, kerb at junction of parapet wall & roof etc, complete all as specified and directed.

Rendering 15 mm thick on brick work or concrete surfaces in CM 1:6 and finished even and smooth without using extra cement, complete all as specified and directed.

Rendering 15mm thick cement plaster in cement mortar 1:4 on on brick work or concrete surfaces and finished even and smooth without using extra cement complete all as specified and directed.

Rendering 10mm thick on concrete surfaces in CM 1:3 in ceiling/chajja/roof projection and finished even smooth without using extra cement complete all as specified and directed.

Filleting as in repair not exc.25 sq cm in any position and to any shape in cement mortar 1:3 including all mitres ,stops,etc ,complete all as specified and directed.

Granite work ( any type) 20 mm thick ( table rubbed & polished) in steps,jambs, pillars, window cills, cooking plateform & like in cement mortar (1:4) including pointing into white cement (1:2) using marble dust with admixture of pigment to match shade of granite over and including 15 mm thick screed bed in CM 1:4, complete all as specified and directed.

Non skid coloured ceramic tiles (1st quality) 7 to 8mm thick(square/rectangular joint free) area of each tiles exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding layer of mortor 15mm thick in CM 1:6, complete all as specified and directed

Glazed coloured ceramic tiles (1st quality) joint free in vertical surfaces of wall of size 450x350x7mm/350 x250 x 7mm thick set & jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering in CM 1:4 on brick /concrete surfaces complete all as specified and directed .

Coloured ceramic tiles (1st quality) 8 to 10mm thick, joint free (square/rectangular joint free) area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding layer of mortor 15mm thick in CM 1:6, complete all as specified and directed.

Coloured ceramic tiles (1st quality) 8 to 10mm thick, joint free (square/rectangular joint free) in skirting, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4, complete all as specified and directed.

Machine cut kota stone slab flooring 20-25mm thick over and incl 20mm thick cement screed base in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Kota stone floor 18-20 mm thick and including 10mm thick CM 1:4, as in riser of steps, skirting, dado, set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area not exceeding 1.50 square metre each, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from frames) area exc 1.5 sqm but not exceeding 4 square metre each, complete all as specified and directed.

Pressed steel frames 125x60mm for doors made out of 1.25 mm thick sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and directed.

Pressed steel frames 105x60mm for doors made out of 1.25 mm thick sheet with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and directed.

Block boards 25 mm thick, grade 2 quality, interior grade, decorative type with decorative face veneer on both faces fixed with screws to timber frame-work, fixed in repairs complete all as specified and directed.

Prelaminated particle board 18/19 mm thick, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work in repairs, complete all as specified and directed.

Continuous (piano) hinges, mild steel, bright finish or electrogalvanised, Width of flaps (when open) 40mm, complete all as specified and directed.

Hasp and staple, 100mm size, safety type, aluminium anodised including bolt to hinge plate and fixed with screws, complete all as specified and directed.

Factory made PVC internal UPVC (rigid) door frame of the size 50mm x 95mm with a wall thickness of 5mm, made out of extruded 5mm thick, PVC sheet of density 600kgs/cbm manufactured by an ISO-9000 certified company, mitre cut at two corners and joined with 4 nos of 150mm long brackets of 15mm x15mm M.S. square tube of 19 guage through out the frame .The door frame shall be fixed to the wall using 65/100mm long M.S. screws through the frame by using anchor fasteners.A minimum of 4 nos .of screw to be provided for each vertical member & minimum 2 nos. for horizontal members etc. complete all as specified and directed.

Factory made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face, complete all as specified and directed.

35mm thick, IInd class H.W.Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated , complete all as specified and directed.

Glazed and skeleton shutters 35 mm thick, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); kiln seasoned and chemically pressure treated, complete all as specified and directed

2nd class hard wood 100mm thick frame with louvred frames 80 to 100mm with fixed louvres of 4mm thick frosted glass to frame put together , complete all as specified and directed.

Stainless steel wire cloth,0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed.

Stainless steel wire cloth,0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples fixed in repair ,complete all as specified and directed.

Aluminium alloy, anodised sliding door bolts(250mm long) with hasp,staples( bolt type) and fixing clip of sheet,cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed ,complete all as specified and directed.

Aluminium handle 150 mm long cast type anodised, complete all as specified and directed

Aluminium tower bolt 200 mm long, anodised barrel tower bolts of extruded section complete all as specified and directed.

Aluminium floor door stopper (150 mm long) of aluminium alloy body and tongue, anodised with hard drawn steel spring complete all as specified and directed

M.S. helical door spring (150 mm long) including roller and roller plate complete all as specified and directed

Butt hinges 100 mm medium weight stainless steel complete all as specified and directed

Sheet glass, ordinary quality 4.00 mm thick and glazing with oil putty in square not exceeding 0.5 sq m in each pain, fixed in repair, complete all as specified and directed.

Figured sheet glass , ordinary quality 4.00 mm thick and glazing with oil putty in square not exceeding 0.5 sq m in each pain complete all as specified and directed.

Taking down GI pipe 15mm bore steel tubing and connections including cleaning for refixing or removal from site complete all as specified and directed

Taking down GI pipe 20mm bore steel tubing and connections including cleaning for refixing or removal from site complete all as specified and directed

G.I. pipe 15mm bore tubing medium grade galvanised with all fitting fixed to wall, ceiling and laid in floors complete all as specified and directed

G.I. pipe 15mm bore tubing medium grade galvanised with all fitting fixed to wall, ceiling and laid in floors, except pipe complete all as specified and directed

G.I. pipe 20mm bore tubing medium grade galvanised with all fitting fixed to wall, ceiling and laid in floors complete all as specified and directed

G.I. pipe 20mm bore tubing medium grade galvanised with all fitting fixed to wall, ceiling and laid in floors , except pipe, complete all as specified and directed

Complete removel of existing old water proofing treatment from sunken portion surface and preparation of old concrete surface by picking, sweeping,cleaning and washing down with water, remove dust etc including provn of cement concrete 1:2:4 type B-0(using 12.5mm graded stone aggregate) as in sunken portion with application of WPT hepercrete ratio(1:1), water proofing treatment with fibre mesh jalli two components water proofing coating material applied in two coats to a thickness of 1mm,rendering 15mm thick CM 1:3 on fair faces of brick work or concrete and mix with water proofing compound and finished even & smooth complete all as specified and directed.

Cement concrete 1:7:12 type F-2 (using 40 mm graded stone aggregate) as in sunken filling , complete all as specified and directed

Vitreous china ,Squatting pan 'Orissa' pattern size 580x440mm white with integral foot rest including all joints and making good to the floor etc ,complete all as specified and directed.

Vitreous china WHB size 550x400mm including cutting or pinning inends of brackets or erecting incl32mm dia waste pipe complete all as specified and directed

PVC valveless, 10 ltrs, syphonic action type, dual type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, fixed in repair, complete all as specified and directed

C.P. Bib taps, long shank(Fancy type) 15mm bore cast copper alloy ,screwed down,screwed for iron pipe or brass ferrule complete all as specified and directed

C.P. pillar tap( fency type 15mm bore)cast copper alloy with capsten head CP screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screw shank and fly nuts screwed for iron pipe complete all as specified and directed.

C.P. Angle valve (fancy type) 15mm bore,cast copper alloy screwed down,high pressure, screwed both ends for iron pipe or unions complete all as specified and directed

C.P. stop cock valve(fancy type) 15mm bore,cast copper alloy screwed down,high pressure, screwed both ends for iron pipe or unions( concealed type)complete all as specified and directed

C.P. shower rose 125 mm size for 15 mm bore pipe, fixed in repair, complete all as specified and directed

Tubular towel rail 20 mm dia chromium plated, 60cm long between flanges complete all as specified and directed

20mm bore stop ball valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

PVC connection 15mm dia, 450mm long with brass nut complete all as specified and directed

Sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm, bowl size 410mm x 330mm x 160mm , complete all as specified and directed.

Steel kitchen plate rack of size 600x750x250 mm, complete all as specified and directed.

Rotational moulded polye- thylene water storage tanks of capacity 500 ltrs Three layered ISI marked, white colour (cylindrical vertical with closed top) hoisted and fixed in position including all necessary connections all as specified in SSR Part I including dismantling of existing water storage tank, complete all as specified and directed.

20mm bore ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. complete all as specified and directed.

Dismantling of PVC(SWR) drain pipes up to 110mm dia, jointed in cement mortar and taking out from trenches,if required complete all as specified and directed.

Taking down eaves gutters and PVC rainwater pipes (any size or pattern), including all fittings,heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed

PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed

PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed

PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed

PVC (SWR) floor trap, 75mm dia outlet, plain with grating including jointing with solvent cement complete all as specified and directed.

PVC (SWR) 110mm bore bends any radius, complete all as specified and directed.

PVC (SWR) 75mm bore bends any radius, complete all as specified and directed.

PVC (SWR) 110mm bore bends any radius with access door, complete all as specified and directed.

PVC (SWR) 75mm bore bends any radius with access door, complete all as specified and directed.

Cutting chases,pining in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landing steps, cills, sunshades ,shelves,lintels,etc.; and cutting chases for concealed water tubing or concealed conduit,wiring,etc,and making good cutting not exceeding 10 cm in girth brick walls. complete all as specified and directed.

Preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Preparation of old wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Preparation of old steel or iron surfaces of any description over 10 cm width or girth and applying one coats of synthetic enamel paint complete all as specified and directed.

Preparation of newly plastered surfaces of walls etc and applying two coats of cement based paint over one coat of primer , complete all as specified and directed.

Preparation of old surfaces of walls etc and applying one coat of cement based paint , complete all as specified and directed.

Complete removal of existing old treatment on wall surface all as specified and directed.

Preparation of plastered surfaces of walls and applying two coats of oil bound distemper over a coat of wall care putty , complete all as specified and directed.

Preparation of newly plastered surfaces of wall and applying three coats of white wash complete all as specified and directed

Preparation of old plastered surfaces of ceiling and applying two coats of white wash , complete all as specified and directed.

Preparation of new untreated plastered surfaces of wall and applying two coats of synthetic enamelled paint over a coat of wall care putty, complete all as specified and directed.

Preparation of new plastered surfaces of ceiling and applying two coats of white wash , complete all as specified and directed.

Cement concrete type D-2, 1:4:8(40mm graded crushed stone aggregate) as in foundations,filling and mass concrete, sub base floor, complete all as specified and directed.

Pre-polished chequered cement concrete tiles of size 30 cm x 30cm x 25 mm thick, set & jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 20 mm thick cement screed bed in CM 1:6 complete all as specified and as directed.

Machine pressed precast concrete interlocking paver block of any shape and size approved by EIC, ISI marked (IS:15658-2006) 60mm thick, M-35 grade (Medium Traffic), in paths and hardstanding,with grey cement and pigment, laid tightly over & including 25mm thick dry sand cushion (compacted) and joints filled with dry sand, colour and pattern as approved by GE, complete all as specified and directed.

PCC 1:3:6 type C-2(using 20 mm graded crushed stone aggregate), 75mm thick as in plinth protection finished even and smooth without using extra cement laid in bays not exc. 2.00m and joints filled with bitumen sand mastic with ratio (1:3 ) complete all as specified and directed.

PCC 1:3:6 type C-2 using 40mm graded stone aggregate as drains complete all as specified and directed.

20mm dia dropery curtain rod mild steel powder coated with suitable brackets and end caps fixed in repairs.complete all as specified and directed.

Excavating in post hole each not exc 0.5 cum, getting out, returning, filling in any type of soil and ramming earth or brocken rubble mixed with earth around in layers not exc. 25 cm, complete all as specified and directed.

Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in hard and dence soil, complete all as specified and directed.

PCC 1:3:6, 75 mm thick,Type C-2 (using 40mm graded crushed stone aggregates) as in sub base in floor, complete all as specified and directed.

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth: for foundation etc or for shafts,wells, cesspits, manholes, pier holes, etc n exc 10 sqm on plan and n exc 1.5m in depth and getting out in hard & dence soil, complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm, hard & dence soil, complete all as specified and directed.

Removng excavated material (soil) n exc 50m and depositing where directed at a level n exc 1.5m above the starting point,complete all as specified and directed.

Steel work in tubular trusses including special shaped washer etc, using ERW or induction butt welded tubes conforming to I.S. 1161-1979 grade St.-240, complete all as specified and directed.

Roof trusses (framed), trussed, purlins, rafters, crane gantries, rails and fastening and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats, MS plate, welding, bolts etc conforming to Fe-290 (Gde E-165). complete all as specified and directed.

Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws, complete all as specified and directed.

Formwork to sides of concrete foundation, footings bases of columns, rafts and raft beams, sides and soffits of plinth beams and similar works with rough finished flat surface of concrete, complete all as specified and directed.

Formwork to sides of Pillars, posts, fair finished surface of concrete, with rough finished flat surface of concrete, complete all as specified and directed.

Formwork to sides and soffits of roof beams and similar works with rough finished flat surface of concrete, complete all as specified and directed.

RCC M-25 (Desgin mix) as in foundation, footing, foundation beams, plinth beams, bases of columns etc complete all as specified and directed.

RCC M-25 (Desgin mix) as in Columns, pillars, piers, posts, struct etc complete all as specified and directed.

RCC M-25 (Design mix) as in beams, cantilevers etc complete all as specified and directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Mild steel TMT bars 5mm dia and over upto and including 10mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete drilled for fixing of steel sheeting or other covering. Doors etc to be prepared for hanging or sliding with and including either hooks and hings or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete, Fe-290 (Gde E-165) complete all as specified and directed.

Dismantling structural steel wk in cluding doors, gates but excluding framed truss etc.complete all as specified and directed.

Mild steel , plain, black sheet 1.6mm thick in walls,cladding, steel gates and similar works,cut to size,holes punched:including round headed screws,clout nails or rivets and fixed to wood or steel framing with plain 40mm lap joints with riveted or wilded seams,including bending or turning up,mitred angles etc as required complete all as specified and directed.

MS work as in posts and struts in fencing including cutting tops to shape as directed, drilling holes notching for wire, etc: flat iron fillets(for securing wire mesh) including all neccesarry drilling, bolting or riveting etc and similar works conforming to Fe-290 (Gde E-165) complete all as specified and directed.

Galvansied 2 strand, steel Barbed wire with 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining & fixing to any type of standard rails strain-ing bolts including securing or tying at cossing with and provn of galvanised mild steel wire, staples or steel pins, etc complete all as specified and directed.

Concertina coil having dia 600mm with blade thickness 0.47mm and core wire diameter 2.5mm with minimum zinc coating on wire minimum 275 GSM wt 14.63kg each coil. complete all as specified and directed.

Taking down and refixing C.P. Bib taps, long shank(Fancy type) 15mm bore cast copper alloy ,screwed down,screwed for iron pipe or brass ferrule complete all as specified and directed

Taking down old unserviceable aluminium point wiring (light, fan, socket , power socket and bulk head fittings) from PVC/metallic conduit,on surface wiring, on wooden batten/casings & caping complete, including fixture and fittings such as switches, ceiling roses,pendents holder, regulators, sockets and defective main switch/DB/MCB/Metal plug etc. by unscrewing carefully from boards etc complete all as specfied and directed.

Point wiring for light / fan controlled by one switch with 1.5 sq mm single core PVC insulated unsheathed multistranded copper conductor FRLS with in and including PVC concealed conduit having thickness not less than 1.8 mm with all fittings including anodised pressed steel sunken box having thickness not less than 2mm with 3mm thick ISI marked bakelite laminated sheet fixed with cadmium plated screws and washers for switches and sockets, including 1.5 sqmm single core PVC insulated unsheathed multistranded copper conductor FRLS as earth continuity conductor connected to common earth dolly including, cutting chiseling for concealed piping including insulation test of point wiring and making good disturbed surfaces area and white wash/colour wash to matching with the existing colour and point wiring connection will be tapped from nearest point and complete all as specified and directed. Note: (a) Insulation test of point wiring (b) Colour coding is to be maintained .(Ph-Red, N-Black, Half -Yellow, Earth- Green)

All as per srl item No 125 above but for One light point controlled by two way switch complete all as specified and directed.

All as per srl item No 125 above but for Call bell point , complete all as specified and directed.

All as per srl item No 125 above but for 3 pin 5 amps independent board complete all as specified and directed.

All as per srl item No 125 above but for 3 pin 5 amps same board complete all as specified and directed.

Point wiring with 2.5 sqmm single core PVC insulated unsheathed multistranded copper conductor (FRLS) with in and including PVC casing & caping with all fittings including anodised pressed steel sunken box having thickness not less than 2mm with 3mm bakelite laminated sheet ISI marked suitable for 5 pin 15 amps socket outlet ,including 2.5 sqmm single core PVC insulated unsheathed multistranded copper conductor (FRLS) as earth continuity conductor connected to comman earth dolly including cutting chiseling for concealed piping and making good disturbed surface area and white wash /colour wash to matching with the existing colour complete all as specified and directed.Note: (a) Insulation test of point wiring (b) Colour coding is to be maintained .(Ph-Red, N-Black,Earth- Green)

Switch piano flush type single pole, 5 Amp, one way, AC 230 volts etc complete, all as specified and directed.

Switch piano flush type single pole, 10 Amp, two way, AC 230 volts etc complete, all as specified and directed.

Switch piano flush type single pole, 15 Amp, one way, AC 230 volts complete, all as specified and directed.

Socket outlet 3 pin 5 amps flush type complete all as specified and directed.

Socket outlet multipurpose 2 in 1, 6 pin 6 and 16 amps controlled by one switch flush type universal .

Bell push flush type with indicator 6 Amps complete all as specified and directed.

Electronic bell ding-dong AC 230 Volts single pole complete all as specified and diercted.

Ceiling rose 65 x 50mm three terminals complete all as specified and directed.

Ceiling fan regulator electronic type 5 stage speed variation,socket type is size, ISI marked complete all as specified and directed.

Lamp holder/batton holder/angle holder insulated body(Metal ring) with back bakelite plate suitable for batten fittings.

LED tube light fitting 20 watt, 230 volt,box type complete bipin holders, connector,mounted on PVC block and retro LED rod of 20 watt with aluminium heat sink & polycarbonate diffuser having high efficacy (single side connection) complete with all accessories internally pre wired batten(single side connection) and including connecting up with three core twisted flexible copper conductor cable with suitable size complete all as specified and directed,LED tube rod ,make :Havells ,cat part no:REGALBATTENT5UPTO1X22WSSBSWH and LED tube light batten ,make :Havells , Cat Part No :PHOTONULTRAE2.01213T8SSTL20WLED865SPC or technocommerically equivalant make of Crompton/Philips Note: (i) Contractor shall produce LM 79 & LM 80 test report form OEM owned NABL accredited laboraory. (ii) Contractor shall give gurantee of complete fitting/ fixtures for minimum of 5 years form the date of completion. (iii) Contractor shall conduct the inspection of company representative at site before installation of fittings/fixtures at no extra cost. (iv) Contractor shall arrange 70 % material at site for approval of GE before incorporation in the work.

Environmental friendly, ultra modern, energy saving, surface mounted, decorative hexagon Bulk head 10 watt back-lit LED luminaire comprissing of high brightness LEDs Cat Part No HEXAFT10WLED857SSYMBOPC of Havells or technocommerically equivalent to Philips/Syska/Crompton.

Sheet metal enclosures distribution boards, double door ,VTPN, 415 volts 4 ways (one incoming three phase & twelve out goings single phase )for MCCB & MCB,s comprising three phase four wire copper strip bus bar of appropriate capacity complete all as specified and directed and comprising of the following a) MCCB FOUR POLE 100 AMPS AC 415 VOLTS 25 KA=01 NO (for incoming ) (b) MCB SP 06- 40 amps = 4 Nos (for outgoings) . ( Note :- (i)The DB shall be VTPN series of Make : Schneider ,Cat Part no: A9HVD04L or equivalent make of L&T/ ABB . (ii) The DB shall be flush fixed and making good the disturbed surface matching with existing specifications shall be part of job at no extra cost.(iii)connection of the MCCBs/ MCBs with cable shall be made through appropriate size pin /bottle type thimble properly crimped.(iv) All the vacant holes of the DB shall be provided with blank plates of appropriate size. (v) Double continuous earth wire shall be provided for each three phase DB from earthing mains dolly. (vi) cutting chasing shall be part of job at no extra cost .

Sheet metal enclousre for DBs when MCB to be used double door powder coated factory made flush fixed complete with 200 amps rated bus bar 240 volts single phase 08 ways complete all as specified and directed.

MCB SP 6-32 amps 240 Volt 'B' series complete all as specified and as directed.

MCB SPN 32 amps 240 Volt 'B' series complete all as specified and as directed.

Taking down the unservicable /brunt sub main wiring from wooden batten and provisioning of submain wiring in and including PVC conduit 1.8 mm thick ,20 mm dia with two run of PVC insulated, unsheathed multistranded copper conductor of 4 sqmm(FRLS) and one run of PVC insulated,unsheathed multistranded copper conductor 4 sqmm (green in colour) for earth continuity conductor and connected to common earth dolly with thimble etc, complete all as specified and directed. (Two run of 4 sqmm plus one run 4 sqmm of earth wire will be measured as 1RM) Note: (a) Insulation test of point wiring (b) Colour coding is to be maintained .(Ph-Red, N-Black,Earth- Green)

Earthing complete with galvanised steel earth plate electrode, 600mm x 600mm x 6mm thick, buried directly in the ground (earth pit not less than 2.25m deep below normal (ground level) with top edge of the plate not less than 1.50m below ground level connected to galvanized iron wire 4mm dia as earth lead by means of bolts, nuts and washers of GI up to test point, GI tubing 15mm bore light grade protection pipe, GI watering pipe 20mm bore medium grade with funnel and wire mesh, charcoal and salt, 40mm thick pre-cast RCC (1:2:4) type B-0 (Nominal mix) cover reinforced with XPM (weighing n.less than 4 Kg/Sqm) with suitable steel handle, and angle iron 40X40X3mm frame and chamber of PCC (1:3:6) type C-0 (including earth work in any type of soil, removal of surplus soil to a distance n.exc.50m) and connecting, testing on completion, all as shown on electric plate No. 03 of SSR-2009 Part-I, complete all as specified and directed. Notes: 1. Earth lead & protection pipes length upto & including 7.50 metre is included in the quoted rate. 2. Soil should be free from stone, boulders, aggregate, gravels etc.

Note:- The contract sum arrived after deduction of amount of Sch of credit as listed in tender Documents.

M/S RAJESH SHARMA & CO.

M/S BAWA TRADING CO

s k construction co

M/S SURINDER KUMAR

THAKUR BUILDERS AND CO

NARESH KUMAR AND COMPANY

M/S NAGAR BUILDERS