Detailed survey designing and drawing Construction of UGR, GSR, Supplying and laying Clear Water rising main and Distribution Main Compound wall Pump House Installation of Centrifugal pump motor with allied works etc under DW and S Division Ramgarh

Amount

Elevated Service Reservoir/ Ground Service Reservoir

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand Providing all labours and equipment for designing & construction of ESR all complete job. (Please refer to Section 5,Sl. 2.8 of SBD)

UGR - SUMP

2.00 Lakh Litre capacity

2.00 Lakh Litre capacity

CLEAR WATER PUMPING MACHINERY & ELECTRICAL WORKS AT OHT

Suply, installation, testing and commisssioning of horizontal casing centrifugal pumpsets with alied equipment as (Please refer to Section 5, Sl. 2.5 of SBD)

Supplying. installation and commissioning of Horizontal split casing/End Suction suitable centrifugal pump set of WPIL/ KIRLOSKAR / JYOTI / Mathar and Platt make capable for rated discharge against rated head and mounted of common base plate coupled with SPDP/TEFC squirrel cage suitable capacity induction motor by tyre coupling of KIRLOSKAR / ABB / JYOTI / SIEMENS / CROMPTON/MARATHON/ BHEL make operated on 415 volt ± 10%, 3 phase 50 Hz. A.C supply having suitable or 1480 rpm Including Cost of supplying fitting and fixing of all required accessories such as CI. D/F Sluice Valve, CI. D/F NR Valve, CI. D/F pipe ,foot valve ISI mark and CI D/F pipe of suitable size and length as required for suction and delivery main etc. all complete including cost of supplying, erecting and commissioning fully. Automatic star delta starter [ starter make - L&T/Jyoti/Siemens

/Schineder] of suitable size for required motors etc all comlete as per site requirement including foundation (P.C.C.) making. (Contractor will again check the design of pump & Motor and get approved by the Dept.)

Discharge 6.94 LPS, Head 160 M - (1 W + 1 S)

Supply, installation and commissioning of power control cum cubical panel board, (MCC) made of 2 mm thick MS, sheet of suitable size, dust and vermin proof consisting of following accessories.

a) Incoming feeder-TPN MCCB 250 Amp, thermal release, adjustable and breaking capacity With rotary operating mechanism handle operating mechanism handle (front drive) of L&T/SIEMENS/ Havells/HPL make-1No.

b) Out going feeder 415 V TP MCCB 32 & 63 Amp having thermal release range, and breaking capacity with rotary operating mechanism handle (front drive) of L&T/ SIEMENS ALSTOM/ Havells make- 2 Nos each (Total 4 nos.)

c) Bus bar - 4 pole 250 amp. Copper strip bus bar enclosed In MS sheets etc. all complete iob. - 1 No.

f) Indicating lamp LED -L&T/ SIEMENS make in Red, Yellow and Blue color. -1 set.

g) 32 amp MCB for light load & other loads of L&T/Havells / Alstom - 2 nos.

h) 63 A MCCB as spare of L&T/Havells / Alstom (For Pump sets ) - 1 Nos.

i) 32A MCCB as spare of L&T/Havells / Alstom (For WTP) - 1 Nos.

j) Single phase preventer - 4 Nos.

k) Panel should be duly painted with two coats super enameled paint of approved colour one coat of red oxide primer and internally wired with suitable size of copper wire etc. all complete. (Including their Control Cables and as shown in the attached Diagram) Capacitor or APFC Panel to be provided for desired p.f of 0.96, etc all complete. As per site requirement & IE rules. with lighting arrester for Pump House

Supplying fitting and commissioning of switch disconnecting isolator (TPN) rated current 250A-415V

Supplying triple spur gear type chain pulley block suitable for 3 tone lifting capacity with 6 m lift complete with load chain and hand chain suitable for above lift, tested to 50% of over load as per I.S.3832 carrying ISl mark etc. all complete.

Supplying, erection and Cost of earthing of installation as per I.E. Rules including the earth pit and 8 SWG copper wire in bunch of two and pipe all complete in all equipments (with Charcoal + Salt )

Suuplying & erection of Lightening arreaster of approved make for pump house.

Supplying XLPE/PVC insulated, armoured cable 1.1KV grade with ISI mark Three and half core, stranded aluminium conductor with 6 mm thick 25 mm width M.S. spacer with G.I. Earth wire 6 sq. mm, complete in an approved manner. (3.5 core x 185 Sq mm cable including laying on wall or on floor as and where required from LT line from transformer to Panel of Clear water pumping plant)

Supplying XLPE/PVC insulated, armoured cable 1.1 KV grade with ISI mark Three core, solid / stranded copper conductor with 6 mm thick 25 mm width M.S. spacer with G.I. Earth wire 6 sq. mm, complete in an approved manner. (3 core x 6 and 16 Sq mm cable including laying on wall or on floor as and where required (from Panel to Motor)

16 Sq mm cable

Supplying, erection and Cost of construction of s/s D P structure for required transformer noted below, supplying and erecting steel tabular/rail pole, top bracket channel, back clamp, 11 KV disc insulator with hardware, earthing set complete. MS nut and bolts, MS angle, GI wire, clamp for transformer base, top channel, AB switch, DO fuse ,HG fuse with angle, stay set complete, 11 KV lighting arrester, etc. complete as per the site requirement and as per the direction of E/I and IE rules. (all complete) for (for Power Transformer).

Pure Water Rising main.

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand Laying of Raw & clear water Rising Main (Please refer to Section 5,Sl. 3.0 of SBD)

Providing and supplying ISI mark centrifugally cast (spun) Ductile iron pressure pipes of 100mm and above all diameter for water works with socket and Spigot ends conforming to IS 8329/2000 in standard working lengths of 4.5, 5.5 & 6.0 M for classification K-9 suitable for push-on-joint (Rubber gasket D jointing ) with cement morter lining inside the pipes with outside Zinc and bituminous coating including all other taxes, insurance, and one no. gasket with each pipe, including inspection charges of DGS&D/SGS and sales tax all complete.

100 mm dia pipe -

A) Earth work in excavation (As per IS. 3114/1965) for laying of different types and sizes of pipes so as to give one meter average cover over the socket of pipe with disposal of excavated earth within initial lead and lift as per specification and direction of Engineer in charge (Classification soil item B)

B) E/W in excavation of cut off trenches as per design section in soft rock or ordinary rock (where blasting is not needed) (vide classification of soil item-C with disposal of spoil (beyond 50M away from the toe of dam in country sode) with initial lead of 150M and lift of 15M, including making the section in profile, dressing sides in proper slope and bed in proper grade etc. all complete as per specifictaion and direction of E/I.

Earth work in backfilling the trenches after lying of different types and sizes of pipes with earth removed during excavated within initial lead and lifts as per specification and direction of Engineer in charge.

Supplying labours, tools, tackles, lubricant etc. for laying and jointing D.I/C.I. S/S tyton pipes (class LA) trenches supplying without rubber gasket conforming to I.S.S - 5382-1969) and making gasket joint including providing night guard, barrier and red light to safe guard against accident, all complete ( pipe to be supplied departmentally free of cost and laying of pipe is to be done as per I.S.S 3114-1985 as per deisgn, specification and direction of E/I.

100 mm dia pipe -

Providing and supplying air valve as per IS-14845-2000 and MJP's standard specification of approved make & quality of following diameters including all taxes ( central and local), railway freight, insopection charges, unloading from railway wagons, loading into truck, transportation upto departmental stores / sites unloading and stacking etc. complete.depatmental.

40mm dia

Lowering, laying and fixing in proper alignment and position all type of C.I air valves as directed by engineer in charge including cost of conveyance from store to site of work, cost of all materials and giving satisfactory hydraulic testing etc. comlete. ( for all class of valves.)

40mm dia

Providing Double Flanged Sluice valve (Size 50mm to 1200mm) for scour, confirming to IS 2906/14846 including worn gear arrangements as per test pressure stainless steel spindle, caps including all transportation etc. all complete. [JH-DWSD-SOR- Chapter-1, Sl. No.- 119-C Without byepass arrangement PN 1.6 PN - 1.6

Supplyng labour and tools for fixing C.I sluice valve in trenches with a pair of C.I Tail pieces incluidng making lead caulked joints and flenged koints as per I.S specification , including supplying all jointing materials (Pig lead confirming to ISS 782-1978, yarn confirming to IS.S 6587-1972 and nuts and volts confirming to I.S.S 1364-1983) including drillig holes in flanges if required as per specification and direction of E/I. (Sluice valve and pieces to be supplied department free of cost.).

Supplying tools and tackles for testing of laid D.I pressure pipe up to 60 mm meter head of water all complete as per specification and direction of engeneer- in- charge. Water to supplied free of cost departmentally.

100 mm dia pipe -

Labour cost for one cutting of D.I /C.I Pipes & specials including supplying, necessary tools and plants, chipping or filling the surface finish as per spercification and direction of E/I.

100 mm dia pipe -

Providing and supplying ISI standard D.I specials & fitting with sealing rubber gasket of S.B.R complete with cast iron follower gland and M.S nut & bolts coated or otherwise protected from rusting and suitable for D.I pipes including ED, CST, all taxes, etc. complete as per I.S-9523 but excluding freight. [JH-DWSD-SOR-Chapter-1, Sl. No. 108-A(a)] Including C.P,

Supplying all labours, tool & equipments for cutting pucca or W.B.M road and restoring the same after laying & jointing of pipe lines.

i) Pucca Road cutting-

ii) W.B.M. Road cutting-

Dismentaling plain cement or lime concrete work including stacking servicable materials in countable stacks within 15 meter lead and sisposal of unservicable materials with all leads all complete as per direction of E/I.

Providing PCC M-150 in nominal mix of (1:2:4) in foundation with approved quality of stones chips 20 mm - 6mm size graded and clean coarse sand FM 2.5 to 3.0 including screening shuttering mixing cmenet concrete in mixer and placing in position vibrating striking curing taxes and royalty all complete as per building specification and direction of E/I.

Supplying all materials, labours tools for construction of brick massonary S.V. chamber of size 1.20 x 0.90 (I.D) & 1.50m deep as per standard specification.

Supply all materials & construction of Thurst Block where required.

DISTRIBUTION MAIN

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand Providing all labour, materials, equipment to procure and laying of DI class K-7 pipes with Cement Mortar Lining for distribution main (Please refer to Section 5,Sl. 3.0 of SBD)

Providing and supplying ISI mark centrifugally cast (spun) Ductile iron pressure pipes of 100mm and above all diameter for water works with socket and Spigot ends conforming to IS 8329/2000 in standard working lengths of 4.5, 5.5 & 6.0 M for classification K-7 suitable for push-on-joint (Rubber gasket D jointing ) with cement morter lining inside the pipes with outside Zinc and bituminous coating including all other taxes, insurance, and one no. gasket with each pipe, including inspection charges of DGS&D/SGS and sales tax all complete.

100 mm dia pipe -

A) Earth work in excavation (As per IS. 3114/1965) for laying of different types and sizes of pipes so as to give one meter average cover over the socket of pipe with disposal of excavated earth within initial lead and lift as per specification and direction of Engineer in charge (Classification soil item B) -

B) E/W in excavation of cut off trenches as per design section in soft rock or ordinary rock (where blasting is not needed) (vide classification of soil item-C with disposal of spoil (beyond 50M away from the toe of dam in country sode) with initial lead of 150M and lift of 15M, including making the section in profile, dressing sides in proper slope and bed in proper grade etc. all complete as per specifictaion and direction of E/I. - 30% of (91.88) excavated earth.

Earth work in backfilling the trenches after lying of different types and sizes of pipes with earth removed during excavated within initial lead and lifts as per specification and direction of Engineer in charge.

Supplying labours, tools, tackles, lubricant etc. for laying and jointing D.I/C.I. S/S tyton pipes (class LA) trenches supplying without rubber gasket conforming to I.S.S - 5382-1969) and making gasket joint including providing night guard, barrier and red light to safe guard against accident, all complete ( pipe to be supplied departmentally free of cost and laying of pipe is to be done as per I.S.S 3114-1985 as per deisgn, specification and direction of E/I.

100 mm dia pipe -

Providing Double Flanged Sluice valve (Size 50mm to 1200mm) for scour, confirming to IS 2906/14846 including worn gear arrangements as per test pressure stainless steel spindle, caps including all transportation etc. all complete. Without byepass arrangement PN 1.6

Supplyng labour and tools for fixing C.I sluice valve in trenches with a pair of C.I Tail pieces incluidng making lead caulked joints and flenged koints as per I.S specification , including supplying all jointing materials (Pig lead confirming to ISS 782-1978, yarn confirming to IS.S 6587-1972 and nuts and volts confirming to I.S.S 1364-1983) including drillig holes in flanges if required as per specification and direction of E/I. (Sluice valve and pieces to be supplied department free of cost.).

Supplying tools and tackles for testing of laid D.I pressure pipe up to 60 mm meter head of water all complete as per specification and direction of engeneer- in- charge. Water to supplied free of cost departmentally.

100 mm dia pipe -

Labour cost for one cutting of D.I /C.I Pipes & specials including supplying, necessary tools and plants, chipping or filling the surface finish as per spercification and direction of E/I.

100 mm dia pipe -

Providing and supplying ISI standard D.I specials & fitting with sealing rubber gasket of S.B.R complete with cast iron follower gland and M.S nut & bolts coated or otherwise protected from rusting and suitable for D.I pipes including ED, CST, all taxes, etc. complete as per I.S-9523 but excluding freight. Including C.P,

Supplying all labours, tool & equipments for cutting pucca or W.B.M road and restoring the same after laying & jointing of pipe lines.

i) Pucca Road cutting-

ii) W.B.M. Road cutting-

Dismentaling plain cement or lime concrete work including stacking servicable materials in countable stacks within 15 meter lead and sisposal of unservicable materials with all leads all complete as per direction of E/I.

Providing PCC M-150 in nominal mix of (1:2:4) in foundation with approved quality of stones chips 20 mm - 6mm size graded and clean coarse sand FM 2.5 to 3.0 including screening shuttering mixing cmenet concrete in mixer and placing in position vibrating striking curing taxes and royalty all complete as per building specification and direction of E/I.

Supplying all materials, labours tools for construction of brick massonary S.V. chamber of size 1.20 x 0.90 (I.D) & 1.50m deep as per standard specification.

Supply all materials & construction of Thurst Block where required.

Compound Wall/ Boundry Wall for WTP. (56.40 M Long)

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authority Construction of Compound wall. etc. all complete job.(Please refer to Section 5,Sl. 2.9 of SBD)

Earth work in excavation in foundation trenches in hard soil (Vide classification soil item B) and disposal of excavated earth as obtained to a distance up to 50 Mtr including all lifts, leveling, ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design, specification and direction of E/I

Providing coarse clean sand in filling in fundation trenches or in plinth including ramming and watering in layers not exceeding 15mm thick with all leads and lifts includiing cost of all materials, labour, royality and taxes all complete as per building specification and direction of E/I.

Providing designation of 75A one brick flat soling, joints filled with local sand including cost of watering, taxes royalty all complete as per building specification and direction of E/I.

Providing P.C.C M - 150 with nominal mix of (1:2:4) in foundation with approved quality of stone chips (20mm to 6mm size) clean course sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing R.C.C M - 200 with nominal mix of (1:1.5:3) in foundation with approved quality of stone chips (20mm to 6mm size) clean course sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I.

Centering & Shuttering

Providing RCC M-200 with nominal mix of (1:1.5:3) in stiffeners with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement) taxes and royalty, all complete as per building specification and direction of E/I.

Centering & Shuttering

Providing RCC M-200 with nominal mix of (1:1.5:3) in band at plinth level with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement) taxes and royalty, all complete as per building specification and direction of E/I. Top of Wall

Centering & Shuttering

Providing RCC M-200 with nominal mix of (1:1.5:3) in band at lintel level with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement) taxes and royalty, all complete as per building specification and direction of E/I. Top of Wall

Centering & Shuttering

Providing designation 75 A brick work in CM (1:6) in super structure with approved quality of clean coarse sand of FM 2 to 2.5 including, providing 10mm thick mortar joints cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing 12mm thick cement plaster (1:6) with clean coarse sand of FM 1.5 including screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per specification and direction of E/I.

Providing two coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper, scaffolding, curing and taxes all complete as per building specification & direction of E/I. Qnty. Same as Item no.13

Providing Tor steel reinforcement of 10 mm,12 mm, &16 mm dia Bars as per approved design and drawing excluding carriage of M.S bars to work site, cutting, bending and binding with annealed wire with cost of wire ,removal of rust, Placing the rods in position all complete as per building specification and direction of E/I.

Filling in foundation trenches and plinth in layers not exceeding dressed with earth obtained from excavation of foundation trenches with a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I.

Carriage of materials from divisional store or kiln site or quarry site to work site including contractor's profit, loading, unloading, transportation etc. all complete .

Cement 10 KM lead

Steel 10 KM lead

Sand 36 KM lead

Stone/Stone Chips 11 KM lead

Bricks 06 KM lead

Gate - 1 no.

Earth work in excavation in foundation trenches in hard soil (Vide classification soil item B) and disposal of excavated earth as obtained to a distance up to 50 Mtr including all lifts, leveling, ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design, specification and direction of E/I

Providing coarse clean sand in filling in fundation trenches or in plinth including ramming and watering in layers not exceeding 15mm thick with all leads and lifts includiing cost of all materials, labour, royality and taxes all complete as per building specification and direction of E/I.

Providing designation of 75A one brick flat soling, joints filled with local sand including cost of watering, taxes royalty all complete as per building specification and direction of E/I.

Providing P.C.C M - 150 with nominal mix of (1:2:4) in foundation with approved quality of stone chips (20mm to 6mm size) clean course sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing R.C.C M - 200 with nominal mix of (1:1.5:3) in foundation with approved quality of stone chips (20mm to 6mm size) clean course sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I.

Centering & Shuttering

Providing RCC M-200 with nominal mix of (1:1.5:3) in column with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement) taxes and royalty, all complete as per building specification and direction of E/I.

Centering & Shuttering

Providing RCC M-200 with nominal mix of (1:1.5:3) in band at plinth level with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement) taxes and royalty, all complete as per building specification and direction of E/I. Top of Wall

Centering & Shuttering

Providing Tor steel reinforcement of 10 mm ,12 mm , &16 mm dia Bars as per approved design and drawing excluding carriage of M.S bars to work site , cutting ,bending and binding with annealed wire with cost of wire ,removal of rust , Placing the rods in position all complete as per building specification and direction of E/I.

Filling in foundation trenches and plinth in layers not exceeding dressed with earth obtained from excavation of foundation trenches with a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I.

Supplying fitting & Fixing M.S. grill gate with M.S. grills made 20x6mm M.S. flat or 16mm M.S. square bars fitted 25x25x6 mm M.S. angle frame of size 60x60x6 mm including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C (1:2:4) blocks of required size, applying a priming red lead paint over steel work , taxes all complete as per drawing specification and direction of E/I.

Providing two coat of painting with ready mixed paint of approved shade and make over steel surface

Carriage of materials from divisional store or kiln site or quarry site to work site including contractor's profit, loading, unloading, transportation etc. all complete .

Cement 10 KM lead

Steel 10 KM lead

Sand 36 KM lead

Stone/Stone Chips 11 KM lead

Bricks 06 KM lead

Pump House

Earth work in excavation in foundation trenches in hard soil (Vide classification soil item B) and disposal of excavated earth as obtained to a distance up to 50 Mtr including all lifts, leveling, ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design, specification and direction of E/I For Stiffeners

Filling in foundation trenches and plinth in layers not exceeding 150 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M and lift 1.5 M all complete as per building specification and direction of E/I

Filling in foundation trenches and plinth in layers not exceeding 150 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M and lift 1.5 M all complete as per building specification and direction of E/I

Providing coarse clean sand in filling in fundation trenches or in plinth including ramming and watering in layers not exceeding 15mm thick with all leads and lifts includiing cost of all materials, labour, royality and taxes all complete as per building specification and direction of E/I.

Providing designation of 75A one brick flat soling, joints filled with local sand including cost of watering, taxes royalty all complete as per building specification and direction of E/I.

Providing P.C.C M - 150 with nominal mix of (1:2:4) in foundation with approved quality of stone chips (20mm to 6mm size) clean course sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing R.C.C M - 200 with nominal mix of (1:1.5:3) in foundation with approved quality of stone chips (20mm to 6mm size) clean course sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing RCC M-200 with nominal mix of (1:1.5:3) in band at plinth level with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement) taxes and royalty, all complete as per building specification and direction of E/I.

Providing RCC M-200 with nominal mix of (1:1.5:3) in Column with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement) taxes and royalty, all complete as per building specification and direction of E/I.

Providing RCC M-200 with nominal mix of (1:1.5:3) in band at lintel level with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement) taxes and royalty, all complete as per building specification and direction of E/I. For Door & Window

Providing RCC M-200 with nominal mix of (1:1.5:3) in all types of beam with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement) taxes and royalty, all complete as per building specification and direction of E/I.

Providing RCC M-200 with nominal mix of (1:1.5:3) in Roof slab with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement) taxes and royalty, all complete as per building specification and direction of E/I.

Providing designation 75 A brick work in CM (1:6) in foundation with approved quality of clean coarse sand of FM 2 to 2.5 including, providing 10mm thick mortar joints cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing 25 mm thick damp proof course with cement concrete M-150 with nominal mix of (1:2:4) with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering and mixing cement concrete in mixer with 5% cico or any other approved water proofing compound and placing in position, skirting, curing, taxes and royalty, all complete as per building specification and direction of E/I.

Providing designation 75 A brick work in CM (1:6) in super structure with approved quality of clean coarse sand of FM 2 to 2.5 including, providing 10mm thick mortar joints cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification

Providing av. 63 mm thick RCC M-200 with nominal mix of (1:1.5:3) in Chhajja with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement) taxes and royalty, all complete as per building specification and direction of E/I. For Door & Window

Providing 25 mm thick first class patent stone flooring (1:2:4) with stone chips in two layers, bottom layer 19mm thick (1:2:4) with 20mm to 6mm size graded stone chips and top layer 6mm thick (1:2) with 6mm down stone chips, in panels including cost of curing, finishing the surface smooth by rubbing with carborandum stone, taxes and royalty, all complete as per building specification and direction of E/I.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.

Supplying, fitting and fixing fully glazed steel door, windows or ventilations of standard rolled 'Z' and mullion steel sections and size as per IS - 1038 joints met and welded with 100x16x3 mm M.S. lugs fixed in cement concrete (1:2:4) blocks 15x10x10 cm, size including cost of oxidized iron fittings, with hinges, handle per steps, catch springs, 3 mm thick plain glass panes with Aluminium beads and inner frame fixed with lugs with 20 mm long 6.3 mm G. I. counter sunk machine screw and nuts and applying a coat of red lead paint carriage to work site hoisting and placing in position in all storys and taxes all complete as per building specification and direction of E/I.

Providing 12mm thick cement plaster (1:6) with clean coarse sand of FM 1.5 including screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per specification and direction of E/I.

Providing 6mm thick cement plaster in ceiling (1:4) with clean coarse sand of FM 1.5 including screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per specification and direction of E/I.

Providing 1.5mm cement punning including screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per specification and direction of E/I.

Providing two coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper, scaffolding, curing and taxes all complete as per building specification & direction of E/I. Qnty.

Providing Tor steel reinforcement of 10 mm ,12 mm , &16 mm dia Bars as per approved design and drawing excluding carriage of M.S bars to work site , cutting ,bending and binding with annealed wire with cost of wire ,removal of rust , Placing the rods in position all complete as per building specification and direction of E/I 1.25% of RCC work

Carriage of materials from divisional store or kiln site or quarry site to work site including contract profit, loading, unloading, transportation, etc. all complete .

Cement 10 KM lead

Steel 10 KM lead

Sand 36 KM lead

Bricks 06 KM lead

Stone/Stone Chips 11 KM lead

Add 18% GST

Add 1% Labour Cess

M/S UNIVERSAL TELECOM