GENERAL-Cheramangalam scheme-2023-24 Improvements to Sluice Shutters between 0/000km to 13/400km and Cheramangalam Anicut regulator shutter-.-General Mechanical Work

Amount

Providing rind bund, replacing of rubber seals and seal clamps and alignment correction of hoisting mechanism of Anicut shutters (2Nos)

OD35937/2023-2024:RING BUND -Putting up ring bund as per approved shape 2.5m bottom width, 1m top width using empty gunny/polythene bags filled with earth placed in 2 rows at 0.6m apart and filled in between with puddle clay to form bund for an average height 2.00m including labour dismantling the bund after completion of the work etc. complete.

OD35939/2023-2024:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

OD35938/2023-2024:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

OD35943/2023-2024:Fabrication and supply of Structural steel Canal shutters ( Up to 2tonne weight ) /Hoisting bridge / Platform and accessories etc. as per approved specifications, drawings and directions of deptl. officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied

85.116:Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the gates including cost of SS bolts and nut all labour and machinery and incidental and conveyance charges complete as per approved specification and drawing

85.118:Supplying and fixing in correct position with specified initial interface L-type / bulb nose rubber seal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour and machinery and incidental and conveyance charges complete as per approved specifications and drawings

OD35941/2023-2024:Over coat painting the regulator gates and embedded parts with two coats of epoxy tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns, after cleaning the surface using high pressure water jet including cost of materials, labour, charges, cost of testing all painting materials, incidental charges, hire of T&P etc. complete as per the direction of departmental officers at site.

OD35944/2023-2024:Erection of the Canal Shutter ( Up to 2Tonne weight ) / Hoisting bridge / Platform including hand rails, ladder etc. for the same including alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance, lead and lift charges etc. complete but excluding cost of materials already supplied

85.115:Cost of painting with 2 coats of enamel paint over 1 coat of zinchromate primer as per IS1477:1994 after hand and power tool cleaning including cost of all materials, labour charges, cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

OD38730/2023-2024:Trial running the Vertical lift gate manually including cost of all materials, labour charges etc. complete.

Providing new MS Shutters, Sill beam, SS C -groove, Hoisting girder and mechanism for Regulator shutters (2Nos) at 0/000km

OD35945/2023-2024:Taking out the mud debris and cleaning the bay, removing the plastic and bio waste and disposing at a suitable place 50m away from site

OD35946/2023-2024:Dismantling of the Canal Shutter ( Up to 2Tonne weight )/ Hoisting unit, Embedded parts, etc. of the same and stacking at a distance of 100metre including hire of machinery, labour etc. complete as directed by the departmental officer at site. (Weight of the unserviceable shutters and embedded parts may be calculated as 60% and unserviceable hoisting units as 80%)

15.2.1:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix)

OD35947/2023-2024:DRILLING and FASTENING with TMT rod in concrete/Stone including conveyance and labor charges complete excluding cost of materials already supplied.

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

4.1.2:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:1/2:3 (cement : 11/2 coarse sand : 3 graded stone aggregate 20 mm nominal size)

5.2.2:Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

OD35949/2023-2024:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges

OD35948/2023-2024:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges

OD35950/2023-2024:Supply of MS round bar including cost of conveyance charges

OD35951/2023-2024:Supply of MS BOLT and NUT up to 300mm Length including cost of conveyance.

OD35952/2023-2024:Fabrication and erection of Embedded parts of Canal shutters ( Up to 2 tonne weight ) and accessories as per approved specifications, drawings and directions of deptl. officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied

OD35953/2023-2024:Fabrication, Supply, erection and assembling in correct position and alignment by welding SS Embedded parts in 304L Grade like roller track, seal track, Seal seat etc. as per approved specifications, drawings and directions of deptl. officer at site including cost of all materials, labour, machinery for planing, welding, shearing, grinding etc., lead and lift, conveyance, incidental and handling etc. complete

OD35954/2023-2024:Fabrication and supply of Structural steel Canal shutters ( Up to 2tonne weight ) /Hoisting bridge / Platform and accessories etc. as per approved specifications, drawings and directions of deptl. officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied

85.116:Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the gates including cost of SS bolts and nut all labour and machinery and incidental and conveyance charges complete as per approved specification and drawing

85.118:Supplying and fixing in correct position with specified initial interface L-type / bulb nose rubber seal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour and machinery and incidental and conveyance charges complete as per approved specifications and drawings

OD35956/2023-2024:Providing EN-8 screw rod 7.50 tonne capacity 4.00 M lift screw hoist having one number of EN-8 screw shaft, worm gear units having a lifting speed of around 5.00 cm/min for 24 rpm of hand operation including cost of all materials, labour, hire charges and conveyance. 1m Screw rod, dia 67mm with single start square thread with head pitch of 12.7mm, root dia 62.3mm EN-8 shaft

OD35957/2023-2024:THREAD LESS portion of the screw rod (per metre rate)

OD35964/2023-2024:Providing of Double worm and pinion having a lifting speed of around 5.00 cm/min for hand operation/ manual operation including cost of all materials, labour, hire charges and conveyance.

85.114:Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

OD35955/2023-2024:Erection of the Canal Shutter ( Up to 2Tonne weight ) / Hoisting bridge / Platform including hand rails, ladder etc. for the same including alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance, lead and lift charges etc. complete but excluding cost of materials already supplied

OD35958/2023-2024:SUPPLYING and APPLYING GREASE on NEW SCREW ROD for CANAL GATE

Dismantling existing Shutters, Hoisting bridge, Demolishing Cement concrete manually, Form work and and Concreting for Canal sluice shutter from Ch:0/000km to 13/050km.

OD3916/2023-2024:Dismantling of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting unit / Embedded parts etc. of the same and stacking at a distance of 100 meter including hire of machinery, labour etc. complete as directed by the departmental officer at the site. (Weight of the unserviceable shutters and embedded parts may be calculated as 60 % and unserviceable hoisting unit as 80%).

15.3:Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material with in 50 metres lead as per direction of Engineer -in-Charge.

5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete

5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more

4.1.2:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:1/2:3 (cement : 11/2 coarse sand : 3 graded stone aggregate 20 mm nominal size)

5.2.2:Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

Supply, Fabrication, Painting and Erection of Embedded Parts, Shutters and Hoisting mechanism

OD3917/2023-2024:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges.

OD3918/2023-2024:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges.

OD3919/2023-2024:Supply of MS round bar including cost of conveyance charges.

OD3920/2023-2024:Supply of BOLT and NUT up to 300mm Length including cost of conveyance. (Data for 1Qtl)

OD3921/2023-2024:Providing EN-8 screw rod with one number of EN -8 scerw shaft, hand operation including cost of all materials, labour, hire charges and conveyance. (50 mm)

OD3922/2023-2024:THREAD LESS portion of the screw rod (per metre rate).

OD3923/2023-2024:Providing base and nut arrangement for hoisting the shutter including cost of all materials labour etc complete.

OD3924/2023-2024:Fabrication and erection of Embedded parts of Canal shutters ( Up to 2 tonne weight ) and accessories as per approved specifications, drawings and directions of deptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied.

OD35972/2023-2024:Fabrication, Supply, erection and assembling in correct position and alignment by welding SS Embedded parts in 304L Grade like roller track, seal track, Seal seat etc. as per approved specifications, drawings and directions of deptl. officer at site including cost of all materials, labour, machinery for planing, welding, shearing, grinding etc., lead and lift, conveyance, incidental and handling etc. complete

OD3925/2023-2024:Fabrication and supply of Structural steel canal gate ( Less than 2 tonne weight ) and accessories as per approved specifications, drawings and directions of deptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied.

85.114:Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site

OD3926/2023-2024:Erection of the Canal Shutter ( Up to 2 Tonne weight )/HOISTING BRIDGE/PLATFORM including handrails, ladder etc. for the same including alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance , lead and lift charges etc complete but excluding cost of materials already supplied.

OD3927/2023-2024:SUPPLYING and APPLYING GREASE on NEW SCREW ROD for CANAL GATE (Data for 1m)

MANAF V

Bidder Name

MOHAMMED MUSTHAFA V

MANAF V